hey guys,
please don't get angry with me.
I am just a newbie about upgrading PPC roms. (I was using PalmOS devşces for 6 years until last month)
On my Imate Jasjam I just made a "radio rom update" ; it works fine...
But when it comes to OS updates I am total newbie.
Now I plan to upgrade to WM6 rom but I am too excited. I don't know if I am "ok" to do it.
Do you think the WM6 rom for HTC Hermes works fine on Imate Jasjam ?
(as it is only OS update it should be, but just to be sure)
Any problems that may occur with my Jasjam ?
One other question is:
I know that I have to hard reset before the update. But then, can I restore from my "SK tools" backup over the WM6 OS ?
And last one:
I see on the Radio ROM page that there is a newer radio rom which has "GPS enabled" mark. Also, I see in some of the member's signatures :
"RADIO ROM: 1.35.00.11 (Trinity GPS enabled)"
What does that mean ? Is there really a GPS in all Hermes devices ? Should I only upgrade to that rom to be able to use it ?
Btw, I am sure that most of this is already discussed in one of those very long threads but I am very excited and I wanted to ask it directly.
So please don't flame me...
Thanks for your help.
Hey, there's almost a tacit rule that you have to do a certain amount of reading to be a bona fide member of XDA! Some of your questions indicate that you have done very little... where do you get the idea that you have to hard reset before doing an update!? Start at the WIKI!!
I'll give you this one though... it's an extremely bad idea to retore from a backup after updating the ROM.
Wam7 said:
Hey, there's almost a tacit rule that you have to do a certain amount of reading to be a bona fide member of XDA! Some of your questions indicate that you have done very little... where do you get the idea that you have to hard reset before doing an update!? Start at the WIKI!!
I'll give you this one though... it's an extremely bad idea to retore from a backup after updating the ROM.
Click to expand...
Click to collapse
thank you.
however, I don't understand why it's a bad idea.
I have many apps installed.
To install them from scratch would be too difficult.
I don't think the places in the registry would be different in new rom.
am I wrong ?
my word of advice, If you're not willing to spend time, then upgrade the ROM is NOT for you.
btw, spend a day or 2 to read the WIKI & some of the stickies.
mrmrmrmr said:
thank you.
however, I don't understand why it's a bad idea.
I have many apps installed.
To install them from scratch would be too difficult.
I don't think the places in the registry would be different in new rom.
am I wrong ?
Click to expand...
Click to collapse
You are wrong. As others have said, do some reading before you take the plunge. You'll be glad you did.
And if you keep CAB files on your external storage card, reinstalling apps isn't all that difficult. Trust me, I reflash ALL THE TIME and getting up and running after a flash only takes me about 10 mins. Of course, I don't use half the crap everyone else uses; I mainly stick to a few utils and my corporate email.
Thanks for all of your replies...
Mostly they are discouraging ((
I have read many threads about the upgrade process and I couldn't understand why "upgrade the ROM is NOT for me"
It seems simple as running the exe on the PC.
is there something I missed ?
because if you run the wrong exe file from your pc you will end up with a really expensive paper weight
And you've indicated that you're too lazt to reinstall your favorite apps unless you can simply restore from a back-up.
Hint, experiment... I know which apps will work from my storage card without need a fresh install after Rom upgrade or hard reset.
concur: changing ROMs is like crack... once you start, you're hooked
Best to get proficient with the reloading process since eventually you'll wind up being able to do it in your sleep. I actually reloaded from a cold reset while working out at the Gymn once.... (capital G in geek here...)
thank you for all of your replies.
then I will wait some more to see if a more stable wm6 rom is available.
maybe kyphur can release one which is even better than his forst one
then I will hard reset my hermes (as I will need space on it for the update)
and then run the exe from my computer.
then I will have to install all of my apps from beginning.
I hope I don't lose data
Related
Hey there, I've been anxious to flash my xv6800. I've been reading and searching extensively in the forums and FAQs and the Wiki (I don't usually post until my frustration is out of control). I've found some useful info here:
How-to for Wizard
http://forum.xda-developers.com/showthread.php?t=298613
but didn't see the G3/G4 designation on my splash screen (dead end)
How do I go about flashing to a DCD rom (or any custom rom for that matter)? Is there software I need to install on my comp and are there any steps specific to the xv6800 verizon firmware?
I would really appreciate any help. Thanks
I'm in a similar situation to you. I found this helpful guide the wiki here and it got me started. I also posted a similar plea on the DCD's Titan Rom thread so see if a response turns up there. Good luck and PM me if you find anything helpful. The title of your thread makes it a good place to post for the likes of us.
edit: I bet if this was made a sticky and some informed people posted some helpful info, us noobs would stay out of other threads asking for answers. (sound of kitten stuck in tree)
i need help too
well i got impatient and just downloaded dcd 1.6.10 and just clicked on the .exe without doing anything else. its currently doing its thing, hope it works!
You so crazy! I hope that works, but I have my doubts. The version you're referring to, 1.6.10, is for DCD's Titan kitchen. AFAIK, the kitchen's for cooking your own rom. Cooking is different from flashing as far as I can tell. I think you'll now find that you're ready to make your own rom on your PC, but that still leaves us unsure of how to prepare for and execute the actual rom replacement on the Titan. Right, wrong, Bueller?
it didnt work. it was stuck at 0% forever and then gave an error. i took the battery out and back in and am back to how i was before. no brick
i think i need some sort of bootloader. "re-locker" ? i cant find this when searching.
i thought dcd 1.6.10 is a rom for everyone, and kitchen is for those who want to make their own roms? im so confused.
http://forum.ppcgeeks.com/showthread.php?t=9927
excellent. Thanks!
fusQer said:
it didnt work. it was stuck at 0% forever and then gave an error. i took the battery out and back in and am back to how i was before. no brick
i think i need some sort of bootloader. "re-locker" ? i cant find this when searching.
i thought dcd 1.6.10 is a rom for everyone, and kitchen is for those who want to make their own roms? im so confused.
Click to expand...
Click to collapse
I tried to load dcd's and the official rom and the same thing happens to me, stuck at 0% then connection error.
Been trying to get some info from ppcgeeks.com but the forum has been down since yesterday.
What are we doing wrong?
Throw you a bone
OK, you guys sound real clueless (actually only a little more clueless than me!) so I'll help out. The ROM by itself is all ready to flash to your phone, like reinstalling a new operating system on your PC. The kitchen can be used to customize your own ROM, but I'd suggest you guys read up a bit more before going here. The garden variety ROMs that DCD and others provide is fine for now.
There are utilities on this forum to get you out of the bootloader screen if you get stuck (heppened to me last night). Search around a bit, and certainly read up a bit before flashing. These things are real complicated, but it takes a bit of understanding because the steps MUST be done in the right order, and many impatient folks dive in and get screwed, then complaign to the folks who gave them the files to begin with!
jorge_culv
Maybe ur misunderstanding what's happening.
Whenever I try to flash the device Windows Mobile Device Center closes both the screen on my Mogul and the window on the host pc never moves from 0%
Hope that helps
OK - I'm new to this also but have a question. I know data is lost so does that mean I need to re-establish all my email accounts and contact lists? I installed the cab to allow you-tube and bluetooth data to my tomtom. Also the Touch commander. Is all that gone and I have to redo that as well? Is there a suggested utility to back up as much as possible to restore? I sync with my company email via exchage. Right now everything is basically working fine so hate to take a chance.
Regards... Steve
I ran at a post in the forums that explained why it's important to flash original ROM every time you upgrade to custom 6.1 and outlined proper 6.1 burning steps - flash the original AT&T ROM, ... do something that I forgot, flash radio you want, flash 6.1 ROM...
I don't seem to be able to find it anymore, I've spent over 2 hours searching XDA now... I may be just blind...
Anyone can point me in the right direction?
Thank you in advance.
sergeb said:
I ran at a post in the forums that explained why it's important to flash original ROM every time you upgrade to custom 6.1 and outlined proper 6.1 burning steps - flash the original AT&T ROM, ... do something that I forgot, flash radio you want, flash 6.1 ROM...
I don't seem to be able to find it anymore, I've spent over 2 hours searching XDA now... I may be just blind...
Anyone can point me in the right direction?
Thank you in advance.
Click to expand...
Click to collapse
Its not really necessary, a minority of members have reported issues with WM6.1 ROMs but nearly every user I have chatted with has NOT been able to reproduce the problem.
I have flashed MANY MANY times with WM6.1 and have NEVER once found any issues with hard resets or crashes.
All I can say is use good practice, save any stuff you need to keep....use an exchange (activesync) account to backup your contacts and messages etc....DONT use a backup program (PIMBackup is ok) since moving between builds can cause issues when you restore the backup.
Thank you.
Do you, though, know where I can find them?
They did help me - flashing ROM and following the steps exactly fixed my nasty and long time SMS sending and missed calls problems...
And I forgot to bookmark it ...
Don't know if this is the exact one you want but - http://forum.xda-developers.com/showpost.php?p=1990320&postcount=6
Cheers....
You are the best! That's exactly the post and instructions I have followed in the past. I bookmarked it now and won't lose
Thank you!
Just a thought, when I find something I seriously DON'T want to loose again, I have a file on my pc for all the info I need. I download the links and copy the info into a word doc so even if I have to re-install windows (loosing my bookmarks in the process) I still have the info I wanted to keep with all the necessary cabs and things I need....
Cheers...
PS - That file is now something like 25 gig.....
Thanks for the tip I used to use del.icio.us and then moved to ma.gnolia for my bookmarks.
Hi there everyone.
I have just bought a new HTC Cingular 8525 but it is running windows mobile 5. I would like to upgrade but I cannot find any downloads or instructions on how to do so. I do not want to brick up my new phone. Does anybody know a download link to upgrade to the latest windows mobile version that will work on my phone. Its an american bought phone which is unlocked and I am using it in the UK on Three. It used to be locked to at&t and I am pretty sure much of the at&t rubbish is slowing my memory and speed of the unit. If I were to upgrade will the phone still be unlocked?
Rom version is 2.15.502.3
Rom date is 04/09/07
Radio version is 1.40.30.00
Protocol version is 32.73.7020.16H
Operating system is (build 15706.3.5.2)
I am all new to this and would appreciate any advice idiot proof I have flashed many PSPs and other things but nothing like this.
As I have just got the phone I am still trying to work out how to use it so I have no idea how to do a Hard or Soft reset and have no idea about the roms
Sorry to waste your time
Please help
Rob
You should read through the Hermes wiki: http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
Make sure you install hardspl! If you install the "official" AT&T WM6 install hardspl again, your phone will stay unlocked, even with custom roms. If you flash one of the big storage roms, then go to try another, flash the "official" rom before flashing another custom rom.
Read the wiki: http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
I would also suggest making sure your phone is "super cid" before flashing custom roms, you'll also be able to flash from an sd card if you are super cid.
Read a bunch before flashing any radio roms!!!
Read, read, and re-read before you flash, and you should be fine. They have made the process fairly straight forward, but you can never be too sure. I have never "bricked" my phone, and I jumped in with both feet!
Mustn't flash a lot then because if you did you will end up with a brick sometime... I've always been able to recover my Hermes but there is STILL the possibility it won't.... one day...
ultramag69 said:
Mustn't flash a lot then because if you did you will end up with a brick sometime... I've always been able to recover my Hermes but there is STILL the possibility it won't.... one day...
Click to expand...
Click to collapse
I guess I have been lucky, but I'm sure I haven't flashed as much as others on here. But, I tried to follow the wiki, and tried to learn from others mistakes before I made some of my own. So, I figure if I can flash my Hermes, others should be able to do the same. And I have read up on the issues for when you "brick it", just in case.
I flashed several roms from the beginning (when I got my hermes), and learned a bunch. Then found what I needed/wanted in a rom, and spent days and days and days reading through many threads to find ones that fit me. I actually tried not to flash too much, but that can be a hard temptation to overcome.
So, just trying to pass on what has worked for me, to avoid the hard resets and such.
I would like to attempt cooking my own rom, and have read through tons of info on it, and played with some kitchens. Still working on learning that stuff, it'll give you a good appreciation of what the chefs around here do.
Whenever i get to the update part of the software my htc turns itself off and disconnects?
I then get the error 260?
robiscool said:
Whenever i get to the update part of the software my htc turns itself off and disconnects?
I then get the error 260?
Click to expand...
Click to collapse
I haven't ran into that one, but I went to the top of the page, clicked search, and typed in "error 260" (without the quotes). And got this http://www.google.com/cse?cx=000825...r+260&sa=Search&cof=FORID:0&ie=utf-8&oe=utf-8
hopefully one of those will help you....google is your friend
I found out that its because I'm running vista. I tried to view Mr. Vanx's guide but its no longer there at this link..
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
So I am a bit stuck as I tried to do the following on here..
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners
With no avail. It wont even let me install the HARD-SPL as it just gets stuck in bootloader mode with the error 260.
I have no idea what to do now. This process needs to be simplified more
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26
Now make sure your device is on and activesync (or for vista users the WMDC) is running on your PC
Click to expand...
Click to collapse
I don't have anything running vista.
I still got the same error
thanks for your help though!
Go to post 1160 on page 116 of this thread - http://forum.xda-developers.com/showthread.php?t=296722
It tells you how to Hard SPL your Hermes with the sd card method. It also gives you ALL the apps needed.
After you Hard SPL your phone you can use the sd card method to flash a new OS. Flashing a new OS though requires you to drop steps 5 & 6 (you don't need sspl.exe once you have Hard SPL). Just remember though that the bootloader won't recognize any sd card bigger than 2gb...
Cheers...
Thanks for that. Its just now I have a problem where my phone is stuck on the Tri-Colour screen
Did you format the sd card fat32 (they are default format FAT) and rename the .nbh file to "hermimg.nbh"?
Is the sd card 2Gb or less?
You're on bootloader, is your SPL 1.09 des? If yes then insert the sd card and reset.
Cheers...
it might be an issue with activesync
i read somewhere before that activesync 6.1 won't sync with WM6 on vista machines.
I had to downgrade mine to ActiveSync 6.0 to get mine working again.
just an idea that might work
Hello,
i just want to ask if maybe one of the admins could contact the developers of HSPL, because there are many who bricked their devices because of SPL 3.03. Or maybe one of the developers themselves will read this. HSPL is the last way out in most cases (or finding somebody with a ORT JTAG Tool).
I know that you better should not update a device without collecting information before it. Indeed!
My last phone was a iPhone, so I know what I´m talking ´bout, but sometimes it just happens that you might have skipped any important information or hint.
So please help :/
You bricked your device? wow!
May be you are just stick on the boot screen where it says SPL 3.03, because you tryed to flash a ROM from the SD card that is not for your operator?
Well, if this is the case just flash an older official ROM for your operator, again from the SD card. Than you can use the actual HSPL and flash a custom ROM. That fixed it for me.
idimdim said:
You bricked your device? wow!
May be you are just stick on the boot screen where it says SPL 3.03, because you tryed to flash a ROM from the SD card that is not for your operator?
Well, if this is the case just flash an older official ROM for your operator, again from the SD card. Than you can use the actual HSPL and flash a custom ROM. That fixed it for me.
Click to expand...
Click to collapse
of course i already tried that, does not work.
You are not clear.
Can you get your device to boot loader?
If yes, then you can try Gold card method from there.
yes that still works, but i tried goldcard method today (1 time with the rom which bricked my device und with a custom rom and the original orange rom [my hd2 has a orange branding]) and it was not the solution for my problem :/
edit: oh and if it´s of interest: when trying to flash with goldcard method the rom which bricked it, i get the white screen with "Loading..." in the middle and then it says "Not allow" also on a white screen and "0028002" written in red, then gets back to bootscreen.
well since u can get to ur bootloader consider urself lucky it aint bricked..
Do one thing, get the newest stock rom from htc (same spl 3.03) and make sure its the right one for your device(when you enter your serial no. it should accept and give u a download link).
then try flashing that rom..
It should get you up and running.
After that you can start worrying about getting back to the old spl and/or hardspl
New HSPL
I am stuck with the same thing.
If i could only geat a new HSPL for spl 3.03.0000
[email protected] said:
I am stuck with the same thing.
If i could only geat a new HSPL for spl 3.03.0000
Click to expand...
Click to collapse
Try flashing an older stock Rom one that is covered by hspl via SD card method. Then whenever you like to install that latest 3. 14 Rom do it via usb method.
jjblaster3 said:
Do one thing, get the newest stock rom from htc (same spl 3.03) and make sure its the right one for your device(when you enter your serial no. it should accept and give u a download link).
then try flashing that rom..
Click to expand...
Click to collapse
that´s exactly where my problem is...
my HD2 has a orange branding and is from france. i downloaded a rom from a link somewhere in xda threads, but it´s a really old rom version. the idiots of orange support posted me a link to the touch hd rom^^, so i even don´t know if there is a rom out there.
dunno if it would help posting my serial here...
i tried to decrypt it for finding information about my model, but the only information i can get is the day of production by the first few numbers and letters :/
OlDirty89 said:
that´s exactly where my problem is...
my HD2 has a orange branding and is from france. i downloaded a rom from a link somewhere in xda threads, but it´s a really old rom version. the idiots of orange support posted me a link to the touch hd rom^^, so i even don´t know if there is a rom out there.
dunno if it would help posting my serial here...
i tried to decrypt it for finding information about my model, but the only information i can get is the day of production by the first few numbers and letters :/
Click to expand...
Click to collapse
You might want to look into the download.. if it's an MFG SPL you're stuck with it
Can you provide the link please?
So from what I understand, OlDirty89 failed to read the fine print and is now in possession of an un-usable phone.
I remember when XDA was actually a community where users like this could actually get help when faced with a situation like this...
EX> I was a noob once. My first PPC was a WM5 HTC Wizard/aka/T-Mobile MDA. I actually stumbled across this forum by accident looking for cool new apps for my phone since lets face it.. WM5 is very bland. I saw what I thought was the coolest thing I'd ever seen - a complete OS replacement loaded with new features I'd never seen on a phone before and sure enough, without reading, I downloaded and attempted to flash the ROM. Naturally, it failed and I panicked. I had paid just over $300 for the phone after all.. I came back to this site, opened a new thread titled "PLEASE HELP ME!!" and within an hour, the more seasoned users on this site helped me restore my phone to the factory state and guided me in the right direction, teaching me everything I could have ever wanted to know about WM and how to customize it. I did eventually get that cool custom ROM on my Wizard and became an established member of the community.
^^^^ This is why I absolutely CANNOT STAND flamers... Flaming a user for being less knowledgeable than you is just plain pathetic... Shows what you're like on the other end of the keyboard too... You know it was really funny because I stumbled across a statistic once that stated that 60% of users who join these forums and flame other users are overweight virgins living with their parents... Just thought that was a funny statistic worth mentioning...
Now with all of that being said.. Let's help this guy. He clearly needs it else he wouldn't have posted this thread asking for it. I'm not saying that someone should write a step-by-step tutorial right here in this thread telling him exactly how to undo what he's done, just guide him in the right direction...
This speech really reminds me of a movie I saw not too long ago...
"Pay it forward..."
Just my 2 cents...
dharvey4651 said:
So from what I understand, OlDirty89 failed to read the fine print and is now in possession of an un-usable phone.
I remember when XDA was actually a community where users like this could actually get help when faced with a situation like this...
EX> I was a noob once. My first PPC was a WM5 HTC Wizard/aka/T-Mobile MDA. I actually stumbled across this forum by accident looking for cool new apps for my phone since lets face it.. WM5 is very bland. I saw what I thought was the coolest thing I'd ever seen - a complete OS replacement loaded with new features I'd never seen on a phone before and sure enough, without reading, I downloaded and attempted to flash the ROM. Naturally, it failed and I panicked. I had paid just over $300 for the phone after all.. I came back to this site, opened a new thread titled "PLEASE HELP ME!!" and within an hour, the more seasoned users on this site helped me restore my phone to the factory state and guided me in the right direction, teaching me everything I could have ever wanted to know about WM and how to customize it. I did eventually get that cool custom ROM on my Wizard and became an established member of the community.
^^^^ This is why I absolutely CANNOT STAND flamers... Flaming a user for being less knowledgeable than you is just plain pathetic... Shows what you're like on the other end of the keyboard too... You know it was really funny because I stumbled across a statistic once that stated that 60% of users who join these forums and flame other users are overweight virgins living with their parents... Just thought that was a funny statistic worth mentioning...
Now with all of that being said.. Let's help this guy. He clearly needs it else he wouldn't have posted this thread asking for it. I'm not saying that someone should write a step-by-step tutorial right here in this thread telling him exactly how to undo what he's done, just guide him in the right direction...
This speech really reminds me of a movie I saw not too long ago...
"Pay it forward..."
Just my 2 cents...
Click to expand...
Click to collapse
Great post
But I hate to say, unless we can get some powerful brainstorming goin on and figure out how to drop an engineering SPL (MFG) with mtty I don't think we can help..
I started a thread a little while back -- Stuck with SPL 2.02.0000 - Test ROM? that you might wanna read through to understand your situation a little better.
And just fyi, you can play/flash between 2.02 and 2.03 without problems, just DON'T try flashing 2.01 from those two.. left me with a lovely little brick.
(this is only if you flashed the 2.03 from this thread)
OlDirty89 said:
that´s exactly where my problem is...
my HD2 has a orange branding and is from france. i downloaded a rom from a link somewhere in xda threads, but it´s a really old rom version. the idiots of orange support posted me a link to the touch hd rom^^, so i even don´t know if there is a rom out there.
dunno if it would help posting my serial here...
i tried to decrypt it for finding information about my model, but the only information i can get is the day of production by the first few numbers and letters :/
Click to expand...
Click to collapse
Use SSPL and it will install your Custom or Stock ROM without any problem.
Download from here http://forum.xda-developers.com/attachment.php?attachmentid=260802&d=1261873816
OlDirty89 said:
of course i already tried that, does not work.
Click to expand...
Click to collapse
IT WORKS! I am also with Orange France and had no issue in reverting back by flashing the latest Orange FR original rom from the SD card.
You can get it here:
http://www.megaupload.com/?d=B9HDHTMW
Then open with winrar or other archiver and extract the ruu_signed.nbh. Rename it to LEOIMG.nbh, and flash it from the SD card.
Scabes24 said:
You might want to look into the download.. if it's an MFG SPL you're stuck with it
Can you provide the link please?
Click to expand...
Click to collapse
http://www.megaupload.com/?d=BC4FGYH4
it´s 1.43
dharvey4651 said:
So from what I understand, OlDirty89 failed to read the fine print and is now in possession of an un-usable phone.
I remember when XDA was actually a community where users like this could actually get help when faced with a situation like this...
EX> I was a noob once. My first PPC was a WM5 HTC Wizard/aka/T-Mobile MDA. I actually stumbled across this forum by accident looking for cool new apps for my phone since lets face it.. WM5 is very bland. I saw what I thought was the coolest thing I'd ever seen - a complete OS replacement loaded with new features I'd never seen on a phone before and sure enough, without reading, I downloaded and attempted to flash the ROM. Naturally, it failed and I panicked. I had paid just over $300 for the phone after all.. I came back to this site, opened a new thread titled "PLEASE HELP ME!!" and within an hour, the more seasoned users on this site helped me restore my phone to the factory state and guided me in the right direction, teaching me everything I could have ever wanted to know about WM and how to customize it. I did eventually get that cool custom ROM on my Wizard and became an established member of the community.
^^^^ This is why I absolutely CANNOT STAND flamers... Flaming a user for being less knowledgeable than you is just plain pathetic... Shows what you're like on the other end of the keyboard too... You know it was really funny because I stumbled across a statistic once that stated that 60% of users who join these forums and flame other users are overweight virgins living with their parents... Just thought that was a funny statistic worth mentioning...
Now with all of that being said.. Let's help this guy. He clearly needs it else he wouldn't have posted this thread asking for it. I'm not saying that someone should write a step-by-step tutorial right here in this thread telling him exactly how to undo what he's done, just guide him in the right direction...
This speech really reminds me of a movie I saw not too long ago...
"Pay it forward..."
Just my 2 cents...
Click to expand...
Click to collapse
thanks for that. we could not be a specialist in everything
netvpn7 said:
Use SSPL and it will install your Custom or Stock ROM without any problem.
Download from here http://forum.xda-developers.com/attachment.php?attachmentid=260802&d=1261873816
Click to expand...
Click to collapse
SSPL does not work on my device at the moment.
idimdim said:
IT WORKS! I am also with Orange France and had no issue in reverting back by flashing the latest Orange FR original rom from the SD card.
You can get it here:
http://www.megaupload.com/?d=B9HDHTMW
Then open with winrar or other archiver and extract the ruu_signed.nbh. Rename it to LEOIMG.nbh, and flash it from the SD card.
Click to expand...
Click to collapse
i´m trying that right now (download is active)
idimdim said:
IT WORKS! I am also with Orange France and had no issue in reverting back by flashing the latest Orange FR original rom from the SD card.
You can get it here:
http://www.megaupload.com/?d=B9HDHTMW
Then open with winrar or other archiver and extract the ruu_signed.nbh. Rename it to LEOIMG.nbh, and flash it from the SD card.
Click to expand...
Click to collapse
Downloading ...
looks like I am also stuck on bootloader with SPl 3.03,nothing I did helped so far,I had HSPL3,my stock Rom was 166.707.
any help is greatly appreciated.
OlDirty89 said:
Hello,
i just want to ask if maybe one of the admins could contact the developers of HSPL, because there are many who bricked their devices because of SPL 3.03. Or maybe one of the developers themselves will read this. HSPL is the last way out in most cases (or finding somebody with a ORT JTAG Tool).
I know that you better should not update a device without collecting information before it. Indeed!
My last phone was a iPhone, so I know what I´m talking ´bout, but sometimes it just happens that you might have skipped any important information or hint.
So please help :/
Click to expand...
Click to collapse
I experienced same things after return my phone for screen problem. Orange france gave me a new one and then my problem began. I made all the needed steps to flash a new radio and Artemis ROM and my phone became crazy. Radio failed at 99%, random soft reset etc... By chance there is a new version (1.72) on the website of orange. With HSPL2 i managed to downgrade the SPL to 1.66 version and flash with the last official orange ROM.
Frequently, my phone continue to soft reset itself and became crazy. Can't use it on a whole day, without soft reset 10 times. I decided to return it to Orange (SPL, ROM and Radio where the good ones). Received a new one, immediatly flash my phone with artemis V36 and radio 2.10.50_28 and all is ok with this last phone.
Probably problems come from the phone and not the way you try to revert back...
idimdim said:
IT WORKS! I am also with Orange France and had no issue in reverting back by flashing the latest Orange FR original rom from the SD card.
You can get it here:
http://www.megaupload.com/?d=B9HDHTMW
Then open with winrar or other archiver and extract the ruu_signed.nbh. Rename it to LEOIMG.nbh, and flash it from the SD card.
Click to expand...
Click to collapse
omg....great. it worked! i love u guys
i knew i will get help here
jovanoti
Hi, I've got the same problem with my Orange HD2.
I can not find any original older ROM to flash with HSPL.
No any chance to install any different rom than my "French language" ROM which is my exact problem I wanna WWE.
Sorry if this is in the wrong section.
My Dad has a network unlocked HD2 with win 6.5 on it, ever since he's had it he's complained that is been unstable, so i decided to look for an updated rom and found 3.14 on the HTC site. Well what a mistake that was! the device is now more unstable than on the previous rom.
The device has crashed and rebooted its self about 7 or 8 times, and frozen completely about 10 times, since i flashed it on tuesday.
A) is this a common problem?
b) other than switch to android is there anything i can do to make the device more stable? (android would be an option but my dad uses the device for work and has bespoke win mo only software on the device.
C) are there any "standard" win mo 6.5 roms that will work on this device?
Thanks
Read this thread
http://forum.xda-developers.com/showthread.php?t=621930
Russ
Does the device have HSPL installed on it?
putting 3.14 over HSPL will be a nightmare, what you need to do is flash task29 then flash 3.14 from SD (not from RUU), that should get you straight.
Thanks both for your prompt replies.
orangekid said:
Does the device have HSPL installed on it?
putting 3.14 over HSPL will be a nightmare, what you need to do is flash task29 then flash 3.14 from SD (not from RUU), that should get you straight.
Click to expand...
Click to collapse
I dont think so orangekid, when i say "network unlocked" he bought it from expansys or somewhere similar, rather than on a contract. its how HTC intended the device to be - god help us!
russpattaya said:
Read this thread
http://forum.xda-developers.com/showthread.php?t=621930
Russ
Click to expand...
Click to collapse
Thanks Russ, i'll have a butchers at that thread, it looks really detailed so hopefully i can sort something for him.
I personally don't hold much belief in this bit of advice, but I've seen it on here so many times that it's probably worth a mention.
After flashing a new ROM, it is recommended by many people that you immediately do a hard reset. It's worth a try anyway!
the ROM is imilkas_vision_sense_v2.1. I used MGRLDR 1.1. As I say it seemed that the phone fully discharged and it wont come back on and boot