After flashing my XDA2 to WM5 3.5a, i've tried merging storage & extended rom to gain memory by following a thread on Airfagev. After doing a hard reset, i found out that my phone is not responding and all i can see are black horizontal lines on the screen w/out backlight. I tried soft resetting it but still it stays the same.
Though i can still put it on bootloader mode, it also wont finish reflashing and an error message appears that goes like this:
ERROR 100: Model ID Error
The ROM image you are trying to use is not designed to work with your Pocket PC.
Is there any way for me to fix this problem? I really need help from anybody who's knowledgeable enough in solving this problem coz' i am new in this field.
Pls. help.
Thanks in advance!
Yoo can use NOID utility for flashing
HimaUpgradeUt_noID.exe
bootloader
Thank you. I can now reflash my device to WM2003 but not to WM5.I think it's because of the bootloader which is v 1.06.Is there any way to change this to v 1.03?
Help pls.
Related
Dear friends
I was tring to upgrade my iMate Pocket PC also know as Himalaya with windows2003 SE , while upgrading I faced problems, the upgarde failed and now I am just getting no display and OS too. The only message displayed is
Serial
v1.03
nothing is working please help
bye with regrads,
your unit is still okay; even better that the usb version is showing on the screen. it's simply stuck on bootloader mode. what kind of problems did you encounter resulting in the failed upgrade?
one suggestion i can give before you downgrade is to try and proceed with the upgrade to se. put your unit back on the cradle but don't expect activesync to "recognize" the device. just put it back on the cradle and rerun the upgrade to se.
same thing happened when i upgraded but to wm2005. the screen showed error and the only thing on the screen was the usb version. i simply cradled back the unit and ran the upgrade. worked.
cheers
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
oh, it appears that you have the "wrong country" id issue. i'm not entirely sure as to how to avoid this but i believe it has something to do with the correct rom version (guys, correct me if i'm wrong). where did you get the rom you used for upgrading to se? downgrading might be the only trick if there is no rom for saudi-based users...but if any chaps presently living there and were successful in upgrading their units perhaps you could share the rom version/s you used?
cheers
yasirirfan said:
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
Click to expand...
Click to collapse
To overcome the Country ID Error, first you need to install this tool...
ftp://xda:[email protected]/Tools/ER2003Edit_1_4_26.zip
Open the ROM file you want to upgrade, then change the appropriate 'Operator ID' code, after this click 'Save ROM image'.
Upgrade ur device. You will no longer face the error message.
I need help, after upgrading to XDA Live Rom i decided to downgrade the radio. The flashing got interrupted cause of MSN and the device got bricked, It stops at HTC splash screen after saying NO GSM. I have tried every method imaginable to recover my poor PDA..
All I can get is to the bootloader where i got IPL-1.01 and SPL-1.09.
I've tried the microSD card thing with the .nbh file named HERMIMG, screen goes white, says loading and then checking and then back to the Tri-colour screen.. nothing done :/
Obviously i cannot get an active sync connection so some thing which i could have tried doing weren't possible to achieve.
I tried using the RomUpgradeUT but i get a porblem with vendor ID with all the ROMS and get an error 262 Update Error, I try to do the recovery thing but the PDA always boots in the HTC splash screen and gets stuck there..
Can anyone help??
can you mtty into the device?
yes.. i can.. tried following instruction and installing as in forums but no results. tried loading the .nb files but never made effect
what happens when you reflash radio rom manually ??
if you didn't have the mfg bootloader you have to use the exe files...
maybe just flash the 1.04 loader and then use the 1.27 radio updater (t-mobile)...
after that reflash the 1.01 mfg and you can flash manually ágain
could you guide me in doing that?? tell me what to download an d how to get the nb files for the radio??? plus i didn't get the hang of the mtty yet... thanks for everything
use this thread for bricked devices:
http://forum.xda-developers.com/showthread.php?t=286755
Please do not open new threads, closing that one.
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
Hello, I am a rookie in equipment from HTC, as well buy a HTC X7500, and then tried to put a 6.1 ROM, however some unknown parameters with the SPL, and tried to install a ROM with SPL 3.5, not anything wrong with the equipment when they turn opens a black screen with white and blue list and some red letters ....
Then I tried to access the bootloader, and everything well, he accessed without problems, but when I try to install a ROM it comes to 1% and equipment shuts down, already researched and I am very tired of trying things and nothing result, someone can help me?
When the ROM update process shuts down at 1%, you should be receiving an error message, either an Invalid Device ID error or a communications error. It is possible that your device is not yet properly SIM/CID unlocked. In any event, try to download and install a original OEM ROM (not a custom ROM) and you should be able to recover your device.
If you want to try again to unlock and load custom ROMs, a bit more reading is recommended.
Thanks but managed to solve my problem with this post:
http://forum.xda-developers.com/showthread.php?t=405814
who has the same problem that you can do this work.
I want to help someone on this please , bcs HTC SPV M3100 when i'm trying to switch on phone was stuck on HTC logo and nothing more , i have try to put on boatloader mode and phone was going on bootloader mode three color screen and show this:
HERM100
IPL-1.04
HERM100
SPL-2.03
i'm trying with hard spl from Pof soft but error getting.
Can someone find a time to help me?
hallooo
experts please!
Hello haveri,
what ROM are you trying to start? I was stuck on HTC logo too, when I tried to start a ROM without installing Striped ROM first, which was highly needed. So I done hard reset(three color screen), and flashed again.
For starters, put in bootloader, connect to PC (1st untick "Allow USB Connections" in activesync) and run Hard SPL V7. Install it on your Herms and hope it works because otherwise you are in for a whole heap of hairpulling frustration...
If you get Hard SPL onto your Hermes then use the sd card method to flash a new rom...
You could have avoided this by doing a little research instead of going full pelt into flashing, you Hard SPL BEFORE you get into trouble, NOT AFTER....
Hi guys,
I have a similar problem with a T-Mobile branded TyTn from a friend of mine who thought flashing ROMs without putting device into HardSPL would be clever.
The devices has also IPL-1.04 and SPL-2.03 and from the bootscreen it looks like WM5 should have been installed. I also get the "NO GSM" message and I REALLY tried every fking method but without success.
I even created a Goldcard (and verified on another device it's working, level 0 instead FF) and tried to flash several ROMs (also Cingular WM5 ROM and original german T-Mobile ROM) but no luck.
I also tried to run HardSPL V7 but as far as I remember it just said it cannot connect.
Funny thing: HardSPL V9 DOES start flashing and on the PDA and the PC the bar shows 100% but some moments later it says "Could not update" (or something like that).
I even tried different mtty methods from several posts from the forum (erasing the NAND on different ways, qtek loader method with erasing the first blocks) but I'm really really frustrated now and I believe there is no solution here?! (device has no guarentee)
So, if someone has ANY hint or useful information write it down or send me a PM.
I gladly appreciate your help and hope for a solution!
Cheers
P.S.: I couldn't find any information saying Goldcard method works (or even exists) for Hermes. Can someone confirm it does really work?