I flashed my locked g4 with faria's shelltool that installed wm6, my phone now wont make it past the ipl/spl screen. at this point i found the sd card backup method and unlocked my g4 through the website. when running through this method i find that the utility is unable to copy the extrom.. it seems to be the last hitch, my phone as of now is a brick and i am hoping for that to change. any help please?
Im not so sure its a brick, I think I read in other posts that if it makes it to the IPL/SPL screen there is still hope.. if it was a brick, I dont think it would do ANYTHING.
You might want to look into that though, I may be wrong, but I am pretty certain there is hope for u.
Hi there.
Turn off the phone, remove battery if necessary. Then press and hold camera button and then press the power button, your phone will enter in boot mode, now flash with the operatorĀ“s rom.
Cheers
sorry for the delayed response here. the phone (even in boot mode ) will not be found by active sync so i cannot get the thing to flash with the t-mo rom. since this issue i contacted customer care and am having the phone replaced under warranty.
the phone will NOT be recognized by activesync.. you just need to start the ROM update and it will go along fine. you need the original carrier ROM, and unless your device is CID unlocked, you need to use ShellTool to flash the WM6 ROM. good luck
-Nstefanelli-
Related
first off let me start off by saying, yes, i'm a noob. i started out by reading all the posts in every thread i could. i have a x10ht that i bought at the local asian mall, not knowing that there were so many problems unlocking it
this is the second failed attempt at flashing a new rom onto my phone. i must say, i am not impressed. it froze the last time, i'm not sure where, and this time at 47%. kinda annoying when u think about it. i took the precautions and followed instructions, but to no avail
can anyone help? i'll give all the details i can...
bl 1.09
radio 1.14
old rom was 1.35
What state is it in now?
if i plug it in to the pc, it goes into bl 1.09
so, i was able to flash the old softbank rom onto it, but now i'm stuck with a japanese device with a sim lock on it(i think). i can't even set up activesync to try to update again. any ideas guys?
I don't have much xp with the ideosyncracies of the Softbank X01ht, but you should be able to build a sspl RUU featuring the os.nb of your choice. I believe you don't want to try flashing the radio ROM area but an os.nb only flash should restore the english version of your choice.
I'd look for confirmation on the above conjecture however, before trying these steps:
download the ruu of your choice and extract the signed nbh file using winrar or equivalent (the exe is an executable rar file)
use nbhextract or nbhdump to extract all the files
use Olipro's RUU builder to create a sspl RUU with only os.nb (use the 06_os.nb extracted from step 2)
flash this onto your device
This procedure should raise a lot of questions for you to research the answers to. The answers are all here I assure you. In researching, you will learn about the techniques of custom flashing for Hermes and whether they can really be used safely on your device.
Flashing the japanese ROM shouldn't have SIM locked you again. However, if it is you can research your free solution on this thread or you can purchase unlock from here.
Also: please explain what you mean by "Can't set up Activesync"
the only problem is right now i can't even access my device... there appears to be some sort of lock on it, something to do with usim and i have no clue what it says. but i can't do anything with it
Its probably saying the SIM is incorrect. You may well be SIMLocked....
You need to get it to the today screen to do sspl flashing. Try resetting with no SIM installed. the first thing you should see after the WM splash is the phone dialer saying "The SIM is missing" in japanese. Hit the cancel button which on my TyTN is the first labeled button above the green button to return to the today screen (you may have to experiment to find the right button).
i do get that, but after a few seconds, it goes to a screen where you can put in a code and there is writing on the left soft button, but you can't select it, i assume until a suitable length code is input, and it has no ok button, so i can't even get out of it... help!!!
and by can't set up activesync i mean that i can only get into the today screen for a very limited time, and activesync doesn't seem to connect fast enough, so i'm kind of stuck.
This happens when there's no SIM installed?
yes, it does. but i may have found out something. i can connect to my hermes through activesync on my work computer... hmmm... let me see here...
wow, that was an experience
so i think i'm good, i'll update you guys as teh day goes on, but i may have fixed this myself, and i feel so releived.
yes, the same usim message was coming up regardless of the way i started it up, but i had about 20 seconds of pda usage before it would come up. i got activesync working via the work laptop on the usim screen, and was able to copy sspl over, i restarted and quickly ran sspl, which got me into des's bootloader. from there, it was just a matter of running the ruu i wanted to run in the first place, WM6 .2, and voila, we seem to be back in business... but i don't ever want to do that again, so i think i'm going to flash that hard sspl... but first to test the radio's and and other features.... wow. last time the flash ****ed up on me, i had to pay this guy $30 to fix it, and tho he did, he never wanted me to know how so i could do it myself next time. screw him!!!!
thanks to everyone and their hard work on the forums here. without you, i'd be styling with a razr rather than hacking this thing apart like it was an xbox or psp....
Hey everyone,
i am so upset and lost; words cannot describe it.
So i installed WM6 black shadow and everything was working except for SMS and MMS. So i am like ok i can live with that for a day till custel' rom will come out. SO i decided to upgrade the radio to 1.43 and boom here is where the problem started, No GSM on boot up. Phone doesn't boot up. I tried install 1.40 over again, still nothing. No i tried upgrade the the rom itself, i tired custel 2.5 and nothing and i tried the new Cingular rom, still same problem. the roms flash all the way. I read the wiki, and saw the mtty.exe thing but that doesn't work for me either. I am really lost and don't know what to do.
Specs
cingular 8525
hardspl v7 cid and sim unlocked.
PLEASE HELP
4.13?? 4.10??
Where did you download these radios from??
or do you mean 1.41 or 1.43??
Yeah thats what i meant, 1.40 and 1.43 sorry. You can see how upset i am.
Thanks Again
Well, if your phone turnes on .. it's not a brick.. lol .. it IS fixable... When you turn the phone on does it go RIGHT to the 3 colored screen?
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
If you are superCID I don't see how flashing a radio could have messed up your phone.. that's weird.
mrvanx said:
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
Click to expand...
Click to collapse
I read everything there and nothing seems to be working for me. I woudnt post for nothing. i dont want to be annoying.
OK im going to repost what ive said on 4wm:
We need to check if your Radio BL is functional, firstly leave HardSPL v7 on there and connect to the bootloader via mtty (il assume you know how to do this).
Issue the following commands and tell us the results please:
1) checkimage (this shows the CRC checksums of each component...id expect the radio image to show a timeout....
2) info 2 (This will verify that your CID is intact)
3) info 8 (does a bad block check)
Once youve done this, flash SPL 1.10.oli to the device and once again connect up to mtty.
4) 'rtask a' this will enter the radio bootloader you will see "Enter Radio Bootloader" or something to that effect
from now on when you type the text does NOT appear on the mtty screen.
5) 'rversion' this should return your radio bootloader version...now unfortunatly if you see nothing...you radio BL is dead and sorry your device is royally bricked. If you get something returned back onto the screen (most probably containing the text '0108') then your radio BL is fine.
Click to expand...
Click to collapse
do as instructed in that text, post your results here.
I cant falsh spl 1.10 oli. it gives me the 260 error.
the 260 error is not connected via USB right? .. weird... have you tried taking your battery out for a couple minutes, then booting into BL mode? sounds weird but this worked for me when I didnt flash hardSPL firsl..
hey mrvanx's
I can't downgrade the hardspl to 1.10, anyhelp.
I cant active sync, the phone doesnt boot up.
Is there anyway to aviod having to respond on the phone.
hey,
i can get the phone to boot up into windows and then it freezes within a couple min. what should i do. Still no gsm message and no phone. thanks
Dan
OK, so let's try and get you to a working state - I've bricked mine a couple of times and it can be quite heart-stopping, eh?
The first thing I would do is re-download radio 1.43, just incase your current one is damaged somehow.
Secondly, download Black Shadow - I know it's not the ROM you ultimately want but the aim here is to get you working again and we can move forward from there.
First, boot up into BootLoader mode (hold down the OK button on the left side of the phone and the power button and then press the reset button on the bottom, just in case you didn't know
You should come to the three colour screen and it should be reading IPL-1.04 and SPL-2.10.Olipro. If it isn't, stop here and post what it does say.
If it everything is OK at this point, when you plug your phone into your computer, it should change to USB at the bottom. Just wait for the Found New Hardware prompts to clear on your PC and then flash the black rom - choose the hardspl option in the flash program.
Once that has finished and it is at the "tap screen to set up windows..." bit, put it back into bootloader mode as above and flash the radio.
This should hopefully give you a running phone again as I know this combination works OK as I am currently using it.
Fingers crossed, don't panic, and let us know what the results are
Cheers,
Smiffy.
Nothing is working, can some please help me. Is there anyt way i can restore the spl to the original one so i can send the phone back, i just got it like 2 weeks ago. thanks
Also i have a bad block thats what i think makes the phone freeze after i boot it up.
How can i get around this, thats seems to be the biggest problem.
Hey everyone, let me give you more info.
I can fully flash any rom and and radio,
phone will boot up like 1 out of 10 times and then freezes and thats it.
i have a bad block number 6. I have hard spl v7 installed before the phone got screwed up. I cant downgrader the spl to a lower one to check if radio stack is screwed up. Can someone please help me, if you need to ask me more info feel free.
I have a 8125 G4 sim unlocked w lokiwiz and a flashed WMSE5_rev4 with soft spl, well the problem that i have now is that i recentley tried to flash a new wm6 rom without hard spl ( yeah i know stupid) And now i am stuck on tri color boatloader screen no matter if i turn it off or not still goes back to the same thing. and yes the rom that i was flashing was g safe, i think were i messed up is not CID unlocking it with hard spl?when i tried to flash the new rom it went all the way to 100% and then gave error after that. NO activesync connection right now
questions
1- DID I BRICK IT
2- is there a way to recover this device
unlock it again. (CID) i had the same thing on my wiz g4. and no. is not bricked.
ok thank you and i will let u know what happens so i should use hardspl right?
ok thank you and i will let u know what happens so i should use hardspl right?
still lost
Ok this is where im at i have tried to flash other roms, NOTHING. the phone is cycling between charging(when on charger) and bootloader every few seconds then i pull it off and nothing. i cant get hard spl to recognize the phone nor will activesync. i understand that i need to CID unlock the phone but i cant even get that far?
any suggestions? please walk me through it im not stupid but HTC's are a whole new ball game for me. im used to motorolas(by the way they suck!)
thanks in advance
Get the original stock ROM for your Wizard version and flash it to get your OS back, then you can HardSPL or SoftSPL.
p.s. G4 Wizard does not have free solutions to actually "CID unlock". Either HardSPL and SoftSPL are hacks that tricks the RUU to allow flashing, you will still see your device as Locked in WST(Wizard Service Tool).
go to activesycn settings turn OFF allow usb connections and retry
I read it here in another thread after I returned My P4300 to cincinati bell in exactly the same condition you described.
Good Luck
Hey, my phone is an At&t 8525 and after finally fixing the white screen problem and flashing hard-spl v7 and a couple of roms I bricked the phone when flashing the last touch flo rom. During the flash the ruu wrapper stopped and indicated there was an error. I did the recovery and it supposedly completed succesfully if I can remember right. When it reboot it would not get past boot loader. And thats where I am now, the phone will not get past boot loader.
I've tried every method on these forum I could found
SD card flashing dosent work, I get the 002..... error in red.
Flashing the factory an at&t rom dosent work either, gets the same error
\
As for as I know the MTTY method dosent work, I don't know how to type in commands into bootloader and when I type in 14 0 in MTTY nothing happens
KITL is not enabled
IPL-1.04
SPL-2.03
The phone does not boot into bootloader when I hit the power button, I have to hold the comm button, power button, and soft reset in order to bring up bootloader.
When bootloader is up and the phone is connected to the computer via usb bootloader displays usb on the screen and windows detects the device as an HTC device.
Again i've spent about a week and a half trying to fix this phone and I don't know what to do anymore, i've tried more methods than listed above I can't remember though. If anyone can give me a hint on what to do I would highly appreciate it. Thanks
P.S Can someone please tell me how you type commands in bootloader or MTTY
You DON'T have Hard SPL V7 installed..... Otherwise your SPL would be 2.10.
Connect the Hermes to the pc, make sure active sync has benn disabled - got to settings, untick connect by USB. It should register on the pc. Go to bootloader then run the .nbh file for your stock rom... Make sure its the carrier rom that it was shipped with. It doesn't have to be WM05 but it DOES have to be your ORIGINAL carrier rom. Let it run through, you may gewt lucky.....
If it works, INSTALL HARD SPL V7....... Makes it so much easier to fix then...
Good luck...
Thanks for the reply, much appreciated
I tried downloading and sd card flashing a stock rom from a list of factory roms of all Hermes that I found here on xda. It gave me the same error though. I'm not exactly sure which exact rom to download from that list either. Any more help would be appreciated, thx
Wow I feel retarded, I used the wrong factory rom. After I used the right one it worked perfectly, I now have my 8525 back! Thx so much man, ur the friggin man!
Congrats bro you got it atlast. good luck & take care your baby in future. try to help others with your experience.
Glad you fixed it mate, but if I were you I'd also make sure you have Hard SPL V7 installed. It is the safety net to help when things go wrong... Never gonna be 100% safe but better odds with Hard SPL V7...
SPL - 2.10 oli
Cheers...
Ok... Rejoining the 8525 Clan
Is this Forum still alive???
Been a while guys, figured I would break out the 8525... charge it up and see what kind of things are new in this community. Unfortunately, it looks as if the radio is bricked on it. Seems like it will install ROM's that the radio is not included on. NO GSM is on the boot display, which is strange as I was using this phone until I got the Tilt about 1 1/2-2 yrs ago. I was a hardcore flasher back then... every other day it seemed, so I know it has (or had) everything it needed like the Oli 2.10 SPL... but it seems like I cannot recover this radio issue.
I am messing with the different original OEM and Carrier ROMs hoping I can get passed the 11-12% mark, and I will let you know if something changes. Any idea if un-installing SPL 2.10 Oli, and then trying to walk back through the old SPL steps could help? I am just trying to figure out another way to get around this radio issue... or basically I have a PDA, no phone Damn phone hasn't been touched in like 2 years, you think it would be just as fine as it was when I took the SIM out.
Cheers
Can u plz tell me how do you fix the white screen problem ?????
kashifmehmood said:
Can u plz tell me how do you fix the white screen problem ?????
Click to expand...
Click to collapse
Please try searching before posting.
Your answer lies within
Thread closed
Hello
I try to upgrade my second HTC Fuze, as same the first one I follow step by step the upgrade process for using TAEL ROM
ROM your trying to flash
TAEL ROM v3.23518
Is the device HardSPL'ed
Yes
Is the device unlocked
Yes
Flashing via USB or SD-Card
SD Card
Phone freezes on the splash boot image, with no option to enter to the bootloader mode.
How can I revive?
Pull the battery for a bit, then put it back in and either soft reset or go into bootloader. The phone should be fine IF you do have hard spl on it (1.90 Olinex, not some other hard spl. If it's another one, the phone is dead.). Then just flash another rom, or re-download Tael's rom. Weird stuff happens if you flash enough. I've had my phone do something sort of similar before, where I couldn't get into bootloader. You may need to soft reset, then let it boot to the alignment screen, then put it in bootloader. Don't worry, it will be ok, hard spl is your parachute.
Thanks you Ted...3 minutes ago I press low volume and power it..and the tri color appeared again....I'm downloading the last rom,
Thanks again
Great my phone is alive again...with the last TAEL ROM
You are right the HARD SPL is the parachute!
Thread close ?!
Thread closed ... another Fuze saved.