Related
first off let me start off by saying, yes, i'm a noob. i started out by reading all the posts in every thread i could. i have a x10ht that i bought at the local asian mall, not knowing that there were so many problems unlocking it
this is the second failed attempt at flashing a new rom onto my phone. i must say, i am not impressed. it froze the last time, i'm not sure where, and this time at 47%. kinda annoying when u think about it. i took the precautions and followed instructions, but to no avail
can anyone help? i'll give all the details i can...
bl 1.09
radio 1.14
old rom was 1.35
What state is it in now?
if i plug it in to the pc, it goes into bl 1.09
so, i was able to flash the old softbank rom onto it, but now i'm stuck with a japanese device with a sim lock on it(i think). i can't even set up activesync to try to update again. any ideas guys?
I don't have much xp with the ideosyncracies of the Softbank X01ht, but you should be able to build a sspl RUU featuring the os.nb of your choice. I believe you don't want to try flashing the radio ROM area but an os.nb only flash should restore the english version of your choice.
I'd look for confirmation on the above conjecture however, before trying these steps:
download the ruu of your choice and extract the signed nbh file using winrar or equivalent (the exe is an executable rar file)
use nbhextract or nbhdump to extract all the files
use Olipro's RUU builder to create a sspl RUU with only os.nb (use the 06_os.nb extracted from step 2)
flash this onto your device
This procedure should raise a lot of questions for you to research the answers to. The answers are all here I assure you. In researching, you will learn about the techniques of custom flashing for Hermes and whether they can really be used safely on your device.
Flashing the japanese ROM shouldn't have SIM locked you again. However, if it is you can research your free solution on this thread or you can purchase unlock from here.
Also: please explain what you mean by "Can't set up Activesync"
the only problem is right now i can't even access my device... there appears to be some sort of lock on it, something to do with usim and i have no clue what it says. but i can't do anything with it
Its probably saying the SIM is incorrect. You may well be SIMLocked....
You need to get it to the today screen to do sspl flashing. Try resetting with no SIM installed. the first thing you should see after the WM splash is the phone dialer saying "The SIM is missing" in japanese. Hit the cancel button which on my TyTN is the first labeled button above the green button to return to the today screen (you may have to experiment to find the right button).
i do get that, but after a few seconds, it goes to a screen where you can put in a code and there is writing on the left soft button, but you can't select it, i assume until a suitable length code is input, and it has no ok button, so i can't even get out of it... help!!!
and by can't set up activesync i mean that i can only get into the today screen for a very limited time, and activesync doesn't seem to connect fast enough, so i'm kind of stuck.
This happens when there's no SIM installed?
yes, it does. but i may have found out something. i can connect to my hermes through activesync on my work computer... hmmm... let me see here...
wow, that was an experience
so i think i'm good, i'll update you guys as teh day goes on, but i may have fixed this myself, and i feel so releived.
yes, the same usim message was coming up regardless of the way i started it up, but i had about 20 seconds of pda usage before it would come up. i got activesync working via the work laptop on the usim screen, and was able to copy sspl over, i restarted and quickly ran sspl, which got me into des's bootloader. from there, it was just a matter of running the ruu i wanted to run in the first place, WM6 .2, and voila, we seem to be back in business... but i don't ever want to do that again, so i think i'm going to flash that hard sspl... but first to test the radio's and and other features.... wow. last time the flash ****ed up on me, i had to pay this guy $30 to fix it, and tho he did, he never wanted me to know how so i could do it myself next time. screw him!!!!
thanks to everyone and their hard work on the forums here. without you, i'd be styling with a razr rather than hacking this thing apart like it was an xbox or psp....
well, so I found out how to fully automate the process. sorry for the waiting, I was busy with life & some diamond and shift stuff
you can now just run an EXE that does all the downgrading and the modelid/wifi restore. no manual lnbs needed.
Description:
this uses a special SSPL, should be also OK in place of the original AthenaWrapper (or Unlocker Step 1), but I recommend you only use it for downgrade purposes.
this package includes:
- NBH to flash back to HardSPL 1.20.Olipro. can be replaced with other SPL NBH's but only with ones that are older than SPL 3.xx are recommended. this is only designed for SPL flash however, do not try other NBH types.
- SSPL which automates the restoring of wifi and modelid, which otherwise would always get corrupt when downgrading from SPL 3.xx. do not try to use another SSPL or you will corrupt your modelid and wifi and you will have to use manual tools (the Athena MAC BIN generator that I wrote & posted earlier) to restore them.
- RUU tailored to these needs. do not try to use another RUU for this purpose. also do not try using this RUU for anything else.
- BIG WARNING: do not even try to run this for any device other than Athena (not even the x7510). (I had to remove all modelid checking.) I do not take responsibility for such moronity (or any other kind of moron actions).
STEP BY STEP:
0. flash AP3newSPL OS image in preparation: http://htc-hackers.com/uploads/ap3newspl.zip
1. make sure Athena is running WM and synced with Activesync. do not try entering bootloader mode manually at this point! the way the Downgrader works relies on this.
2. extract the downloaded zip from Attachment to this post, you'll find an SPLDowngrader.EXE inside. run that EXE on your PC, now Athena should go to tricolour screen saying OliNex SSPL.
3. let the RUU flash.
3-TroubleShooting: if the RUU won't see device, uncheck the advanced functionalities in usb-to-pc settings in settings on the Athena.
4. it will reboot and also will hard reset your device. you will need to flash an OS compatible with old SPL now. if you are not sure how to do that, see "Extra help" below. after that, job is done.
5. +1: you should verify the modelid and SPL version is correct (ATHE100 and 1.20.Olipro). see "Extra help" below on how to enter bootloader mode to check.
Extra help: steps to help with flashing an OS if someone never flashed from bootloader before:
0. do not freak out if the OS isn't booting after downgrade. depends on what OS was on it before. maybe you will only get black screen but do not worry, read further:
1. you should manually enter SPL, by holding camera key (ALL THE WAY IN!!) while resetting. hold it until tricolour screen appears.
2. then use some other RUU / ROM package to flash an OS compatible with old SPL. job done.
NOTE 1: if the exe doesn't run then download and install .net framework from microsoft.com.
NOTE 2: if you just want to restore stock SPL, you must do it this way:
1. flash with this downgrader, with unchanged package.
2. flash OS compatible with old SPL 1.20.Olipro. this can be a stock OS.
3. use usual methods to restore stock SPL. this must be the last step, run only after you've restored stock OS!!!
Planned:
- dedicated stock SPL downgrade package
- dedicated SPL 3.50 upgrade package
these are all available already, just need userfriendly EXE package.
Tested and working great. Excellent Job as usual.
Thank you
Dear god thank you. Does this mean that our lords and lady of ROM cooking will be gracing us with an AP5 ROM sometime soonish?
Perfect!
Now i can try different ROM´s and be sure, i can downgrade to an other, when i dont like a WM6.1 ROM.
Thx!
Awesome Cmonex - Thanks!
Many thanks, cmonex!
Just for clarification on step 4 above,
Do I enter boatloader manullay after this step?....or once this RUU is flashed and I see the black screen, do I just go ahead and flash my desired OS without entering manual boatloader?
Thank you cmonex for this downgrader!!!!!
Kenjari said:
Just for clarification on step 4 above,
Do I enter boatloader manullay after this step?....or once this RUU is flashed and I see the black screen, do I just go ahead and flash my desired OS without entering manual boatloader?
Thank you cmonex for this downgrader!!!!!
Click to expand...
Click to collapse
I edited step 4 to make it more clear - hopefully now you will see what is needed. let me know if still not clear enough.
(P.S: just to give background, RUU without manual bootloader entering will only work if WM is running because the RUU pushes enterbootloader.exe to the device which then puts the Athena in bootloader mode for flash without the user having to do anything. the exe will of course only run if there is an OS running under it.)
Hi Cmonex,
Excellent piece of work as usual, Its pretty clear as it is, You worry to much! Although
sticking with 3.5 for now, we have HTC stock, Ameo WM6 stock, and pawel's good work, and Irus's roms. Why swap?
NOW, have you got XP ROM onto Athena yet, if not why not
regards
Jay
Thanks cmonex, I get it now!
Sorry for the inconvienence!!!!
Thank you for everything ...
Is it possible once made the downgrade back to SPL 3.xx?
If this is so ... How do I do?
Montecristo said:
Thank you for everything ...
Is it possible once made the downgrade back to SPL 3.xx?
If this is so ... How do I do?
Click to expand...
Click to collapse
Just reflash with AP 4.0 again, you will have to go through all the upgrade again to get SPL 3.5 back on. Keep in mind if Pawel comes up with a new rom it may well need SPL 3.5 on to use it. I personaly think its worth waiting.
Regards
Jay
responderman said:
Just reflash with AP 4.0 again, you will have to go through all the upgrade again to get SPL 3.5 back on. Keep in mind if Pawel comes up with a new rom it may well need SPL 3.5 on to use it. I personaly think its worth waiting.
Regards
Jay
Click to expand...
Click to collapse
Same here, I do believe it woth waiting. We just need Pawel and AP team to give us an update on their next complete version.
Cheers
Black screen, Someone can help me!
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
When you were in boatloader ..... I thought you were just only suppose to hit soft reset without the camera button.
Try that!
EDIT: I'm sorry panvita I read your post wrong. I thought you already flashed after the downgrade and you were only just checking to make sure you downgraded successfully by going to the boatloader screen. oops!
panvita said:
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
Click to expand...
Click to collapse
You need to finish the rest of step 4 (or goto the extra help) and flash a 1.2 Rom
Extra help:
Click to expand...
Click to collapse
steps to help with flashing an OS if someone never flashed from bootloader before:
0. do not freak out if the OS isn't booting after downgrade. depends on what OS was on it before. maybe you will only get black screen but do not worry, read further:
1. you should manually enter SPL, by holding camera key (ALL THE WAY IN!!) while resetting. hold it until tricolour screen appears.
2. then use some other RUU / ROM package to flash an OS compatible with old SPL. job done.
Click to expand...
Click to collapse
yes please, why can't people read the instructions? :O
thanks to eagle for answering.
[OT]Women secrets...
How to have a REAL secret diary (and hide it to all males): leave it on the living room table and write in RED on the cover "Instructions Manual" [/OT]
My humble observation for AP4 under SPL 1.2.
panvita said:
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
Click to expand...
Click to collapse
Before I pressed volume bottom and soft reset hole, I was able to see the program menu, and it is still AP4 program. I moved up by my finger, and htc flotouch still worked. I thought that I have had a AP4 under spl1.2, what a wonderful supprise. But after I pressed volume bottom and soft reset hole, what I could do is to go to AP3, and then to AP4, after that, go to downgrader. Finally, I went back to AP4 under spl 1.2. But strange things happened. Each time I soft reset the device, it went to customazation and calibration again. In orther words, I could not restore my backup file which eventually asked for a reset. Finally, I get a conclusion that AP4 cannot be used under spl 1.2 at least the present time. Because I got accustomed with AP4, then I upgraded to AP3 and then AP4 under spl 3.5. Just because my little curiosity, I have travelled around the world twice.
panvita said:
Before I pressed volume bottom and soft reset hole, I was able to see the program menu, and it is still AP4 program. I moved up by my finger, and htc flotouch still worked. I thought that I have had a AP4 under spl1.2, what a wonderful supprise. But after I pressed volume bottom and soft reset hole, what I could do is to go to AP3, and then to AP4, after that, go to downgrader. Finally, I went back to AP4 under spl 1.2. But strange things happened. Each time I soft reset the device, it went to customazation and calibration again. In orther words, I could not restore my backup file which eventually asked for a reset. Finally, I get a conclusion that AP4 cannot be used under spl 1.2 at least the present time. Because I got accustomed with AP4, then I upgraded to AP3 and then AP4 under spl 3.5. Just because my little curiosity, I have travelled around the world twice.
Click to expand...
Click to collapse
wish you had read the forum more times
it is well known that depending on the SPL version you have to get the correct rom version or you will get reset loop. AP4 is only for the newer SPL for now.
Hi guys, for donations:
EDIT: see Raphael Elite Project ROM thread here: http://forum.xda-developers.com/showthread.php?p=2565341 also, donations list will continue there.
UPDATE 2: [SIZE=+2]Hard-SPL released![/SIZE]
[size=+2]NOTE: This is NOT a SIM unlocker - it also doesn't unlock Security for other radios. if you need that, GO HERE[/size]
thanks to Chainfire, martinitime and many others for testing!
Instructions:
1) download Hard-SPL package from attachment, extract to an empty folder. make sure it's launched from a local drive (not through network drive, etc.)
2) you must Have Phone Synced with PC in Windows Mobile!
3) run RaphaelHardSPL-Unsigned_190_1_3.exe,
4) follow steps in the RUU, check device for prompts after PC shows loading bar.
5) it should go to black screen now.
6) SPL flashes, device automatically reboots, job done.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 1.90.OliNex.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned on, press and hold the volume down button, then press the reset button with the stylus tip, then release the volume down button when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from second attachment to the device and run it. then once the screen is black, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
NOTE 3: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, we will soon post a stock SPL downgrade package.
NOTE 4: do not use this RUU for anything other than SPL flashing (i.e. hardspl or stock spl restore)!!! if you want to flash some other rom, then use customruu from: http://forum.xda-developers.com/showthread.php?t=410761
---------
UPDATE: STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
1. download the stock spl package from this post.
2. also download the original hardspl from the attachments in this post.
3. run the hardspl exe but do not click anything in RUU yet. just let the hardspl EXE extract the files for flashing.
4. the SPL you want to revert to is a .NBH file, put the NBH in the extracted hardspl package, overwriting the original NBH file in it!
5. continue with the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to black screen), it goes to 100%, reboots, done.
+6. to verify, volume down + reset, see version number on tricolour screen, should now just say 1.90.0000.
that's it.
will hopefull get one in a week or so as my contract is up for renewal on saturday but stocks are non existent at moment or so ive heard they sold out.
spzero said:
will hopefull get one in a week or so as my contract is up for renewal on saturday but stocks are non existent at moment or so ive heard they sold out.
Click to expand...
Click to collapse
is raphael out on tmobile uk?
still waiting for its release, once i get it lets test the spl
sumitescp said:
is raphael out on tmobile uk?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=2440132&postcount=23
And the next few threads...
Ta
Dave
uhhh.. its a stupid question but how u can say "We have HARD-SPL ready" if u dont have one to test??
I dont know... Its like go to the lions without protection
Of course we dont expect dead devices, but... How is that about "hard-spl" ready?
tramuyo said:
uhhh.. its a stupid question but how u can say "We have HARD-SPL ready" if u dont have one to test??
I dont know... Its like go to the lions without protection
Of course we dont expect dead devices, but... How is that about "hard-spl" ready?
Click to expand...
Click to collapse
yeah, exactly this is why we need testing. it will most probably need extra tweaking, otherwise we would have just posted the file
Ok cmonex! I will inform you when I have a Raphael for testing, just as Diamond
Sat with one in my hand Right now.
What you need me to do?
so we have on person with raphael, how is it going with unsigned hardspl?
What does Hard-SPL stand for?
I wanttt, I wanttttttt... This is the only missing piece of software for my future Raphael, already have the AT&T ROM and Raphael ROM kitchen.
well I had a dedicated tester... he disappeared
rhedgehog: I'll get back to you on this
but it would all be so much easier with a device physically available here...
cmonex said:
well I had a dedicated tester... he disappeared
Click to expand...
Click to collapse
I say we chase after him with torches and pitchforks, the angry mob WILL get that Raphael!!!
happy to help.
may not have it for much longer, but i'll do what i can.....
Olipro, Cmonex,
I 'should' have 3 Raphael's (Voda) for testing around the 27th. If you have not had anyone help test with pre-release units by then count me in. I am pushing for them a little earlier but we shall see.
John
I've got one device my friend. Should be able to test Monday if you want me to.
Cheers
testers
anyone who got the raphael please send me MSN contact info.
djwillis: really appreciate that
hi,
i have brand new raphael.
my icq 3255560
kamma said:
hi,
i have brand new raphael.
my icq XXXXXX
Click to expand...
Click to collapse
added you on ICQ. please accept my auth request and add me too
Before you start, backup anything on your phone you might want to keep after the new Rom has been flashed as all contacts, emails, texts, notes, Internet BookMarks/ ect. WILL be lost!!
PimBackup is good and free (copy any mms attachments to your storage card or computer seperately)
[FONT="]***THIS TUTORIAL IS FOR THE GSM RAPHAEL'S ONLY!!! DO NOT USE WITH CDMA VERSIONS***[/FONT]
[FONT="]If your phone has a SIM Card Slot then its a GSM Model. Carry on reading.[/FONT]
[FONT="]If it has no SIM Card then its CDMA and you should not use this procedure.[/FONT]
[FONT="]**USE THE WIKI FOR EVERYTHING YOU WANT TO KNOW ABOUT YOUR RAPHAEL**[/FONT]
[FONT="]*ONCE YOU HAVE FLASHED A HARDSPL ITS PERMANENT. YOU DONT NEED TO DO IT AGAIN WHEN FLASHING NEW ROMS OR RADIOS*[/FONT]
[FONT="]*DO NOT start another process while the flashing process is taking place*[/FONT]
[FONT="]*DO NOT click off of the status bar... Let it stay in the foreground* [/FONT]
[FONT="]*DO NOT let the Screensaver activate*[/FONT]
[FONT="](any of these can lead to a bad flash and possibly brick your phone)[/FONT]
*FLASH HARDSPL BEFORE FLASHING ANY CUSTOM ROMS*
[FONT="]1. YOUR DEVICE MUST HAVE AT LEAST 50% BATTERY POWER FIRST BEFORE ATTEMPTING EACH STAGE[/FONT]
[FONT="]2. FLASH HARDSPL[/FONT]
Before flashing make sure you have installed Microsoft .NET Framework 3.5 on your PC
[FONT="]Flashing via ActiveSync with USB Lead (thanks to [/FONT][FONT="]OliNex)[/FONT]
1. Download Hard-SPL package and unzip it to your Hard Drive. Make sure it's launched from a local drive (not through network drive, etc.)
2. REMOVE SIM and SD CARDS!!
3. Turn phone back on and let it boot back into your operating system
4. Connect your phone to PC with a USB cable and wait until it syncs with your PC
5. Run RaphaelHardSPL-Unsigned_190_1_3.exe
6. Follow steps in the RUU (Rom Update Utility), check device for prompts after PC shows loading bar
7. It should go to a black screen now
8. SPL flashes, device automatically reboots, job done
9. To confirm you installed it correctly, go into bootloader mode (tricolour screen!) and verify the screen shows 1.90.OliNex
[FONT="]**To enter Bootloader and check HardSPL version; with the device turned OFF, press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears**[/FONT]
[FONT="]NOTE 1: You will not see the SPL version during normal boot, that is the OS version, not SPL![/FONT]
[FONT="]NOTE 2: Anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the download to the device and run it. Once the screen is black, run RUU manually from the PC.[/FONT]
[FONT="]NOTE 3: This is an unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. Also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, go *HERE*[/FONT]
[FONT="]NOTE 4: DO NOT use this RUU for anything other than SPL flashing (i.e. hardspl or stock spl restore)!!! If you want to flash some other rom, then use customruu from *HERE* [/FONT]
[FONT="]3. SIM AND CID UNLOCK [/FONT][FONT="](OPTIONAL)[/FONT][FONT="].[/FONT]
[FONT="]Note: You do not need to SIM or CID Unlock your phone to flash a new Rom.[/FONT]
[FONT="]If, however you want to flash Diamond/ Blacksone Radios OR use your phone on a different Network then you MUST Unlock your phone.[/FONT]
[FONT="]To Unlock your phone go *HERE*[/FONT]
[FONT="]4. DOWNLOAD AND FLASH YOUR PREFERED ROM.[/FONT]
[FONT="]Flashing Via ActiveSync[/FONT]
[FONT="]1. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]2. REMOVE SIM and microSD CARDS!![/FONT]
[FONT="]3. Turn phone back on and wait until it syncs with your PC[/FONT]
[FONT="]4. Run the Raphael_RUU.exe (or [/FONT]RaphaelWrapper.exe if thats included instead) [FONT="]from the Roms Folder[/FONT]
[FONT="]5. Once phone finishes flashing and gets to the screen where it configures the stylus, HARD RESET[/FONT]
[FONT="](hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)[/FONT]
[FONT="]6. Follow onscreen instructions to set up your New Rom[/FONT]
[FONT="]7. Once phone has gone through the customisation procedure then replace Sim and microSD Cards[/FONT]
[FONT="]8. Turn phone back on and set up as required[/FONT]
[FONT="]Flashing Via MicroSD Card[/FONT]
[FONT="]1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)[/FONT]
[FONT="]2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh[/FONT]
[FONT="]4. Copy the RAPHIMG.nbh file to the root of your microSD Card[/FONT]
[FONT="]5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone[/FONT]
[FONT="]7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears[/FONT]
[FONT="]8. Follow the onscreen instructions to start flashing[/FONT]
9. Once phone finishes flashing and says Update Complete, reset with the stylus
[FONT="]10. When it gets to the screen where it configures the stylus, HARD RESET[/FONT]
[FONT="](hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)[/FONT]
[FONT="]11. Follow onscreen instructions to set up your New Rom[/FONT]
[FONT="]5. FLASH PREFERED RADIO IF DESIRED (OPTIONAL).[/FONT]
[FONT="]For more information about different compatible Radios that you can use go *HERE*[/FONT]
[FONT="]**If you want to Flash a Non Raphael Radio then your phone MUST be Security Unlocked** [/FONT]
[FONT="]Flashing Via ActiveSync[/FONT]
[FONT="]Sync your phone with the PC, Run the Raphael_RUU.exe from the Radio's Folder and follow the instructions.[/FONT]
[FONT="]Flashing via MicroSD Card[/FONT]
[FONT="]1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)[/FONT]
[FONT="]2. Download your prefered Radio from the Raphael Rom Develpoment Page and unzip/unrar it to your computer[/FONT]
[FONT="]3. Goto the Radios Folder and rename the .nbh file to RAPHIMG.nbh[/FONT]
[FONT="]4. Copy the RAPHIMG.nbh file to the root of your microSD Card[/FONT]
[FONT="]5. Plug the microSD Card into the phone[/FONT]
[FONT="]6. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears[/FONT]
[FONT="]7. Follow the onscreen instructions to start flashing[/FONT]
[FONT="]8. After the flash finishes press the reset button with the stylus to reset the device[/FONT]
[FONT="]6. JOB DONE[/FONT][FONT="]. Well Done YOU DID IT!![/FONT]
[FONT="]I have attached all the files needed so you dont need to hunt around for anything. Good Luck.[/FONT]
[FONT="]*DISCLAIMER*[/FONT]
[FONT="]I take no responsibility for any fault or damage caused by any procedures within this guide. No warranties of any kind are given.[/FONT]
** FREQUENTLY ASKED QUESTIONS AND HELP WHEN FLASHING **
1. What the benifits are of flashing a new rom?
Flashing a New Rom basically gets rid of all the garbage thats included on Stock Roms and Flashes a Clean, Optimized, Fully loaded Rom that will squeeze every ounce of speed and stability from your phone. Chefs usually include all the programs you are ever likely to need and because the Rom has been cleaned out you are left with more memory to play around with.
2. What are the different types of Unlock? (answer by DaveShaw)
The three stages of unlock are:
SIM: Allows you to use SIM's from another carrier. Can be done using codes or unlocker programs on xda-devs.
Security: Allows you to flash radios from another device (i.e. Raphael) - It does other stuff, but this is all the casual user will use it for
CID: CID unlocking is an old concept, nowadays you flash Hard SPL instead. This lets you flash any ROM, Splash or Radio (depending on sec unlock) to your device. N.B. the CID is the carrier ID (e.g. HTC__001). The stock SPL's only let you flash ROM's that match the CID in the ROM image with the CID on your device.
Also, SuperCID is an even older concept no longer valid on newer devices.
Wow, Great job Mskip!
Just wat i was looking for.
A couple questions though...
1. These instructions will also work on the Fuze, right?
2. Once the phone is done flashing and it is booting up, we are sopposed to HARD RESET when we get to the Stylus Config part?...I didnt know that...ive read some other tutorials, and this step isnt included? ?
Fuze, yes. Sprint, no. There's no Hard-SPL for CDMA phones yet I believe.
Thanks a lot! just what I was looking for (the bit about not needing CID unlock to flash roms.. just hardspl).
gj, mskip, but shouldn't you be clear that your instructions and links are only for GSM Raphaels???? As of the past few weeks the flood gates are now open among 5 North American carriers for the CDMA version of the Raphael. No sense in encouraging confusion and hassles from those less in the know.
There is a release for an unlocker for the CDMA phones, but after a quick search some may mistakenly find themselves to your links and info here.
Keystone said:
gj, mskip, but shouldn't you be clear that your instructions and links are only for GSM Raphaels???? As of the past few weeks the flood gates are now open among 5 North American carriers for the CDMA version of the Raphael. No sense in encouraging confusion and hassles from those less in the know.
There is a release for an unlocker for the CDMA phones, but after a quick search some may mistakenly find themselves to your links and info here.
Click to expand...
Click to collapse
Thanks for the info its been noted in the tutorial. I was only asked to write it last night so any information or changes needed are welcomed
Which button is the "action button"?
mhumphrey said:
Which button is the "action button"?
Click to expand...
Click to collapse
Its the ENTER (center) Button. I have amended the instructions to make that part easier to understand.
might sound stupid, but I think you should say what RUU means and what it is...
first time I flashed hardSPL I couldnt find what this RUU means (while reading steps before flashing).
I started flashing without knowing what it was, when I opened the .exe its title was self-explaining, but its hard to know before starting... because the .exe name is not RUU or something like that
Sorry for bad english!
respider said:
might sound stupid, but I think you should say what RUU means and what it is...
first time I flashed hardSPL I couldnt find what this RUU means (while reading steps before flashing).
I started flashing without knowing what it was, when I opened the .exe its title was self-explaining, but its hard to know before starting... because the .exe name is not RUU or something like that
Sorry for bad english!
Click to expand...
Click to collapse
Done. Thanks for the input
Thanks great guide!
Wish i had this my 1st time flashing i was confused as ever
Thanks for taking the time to write this guide for all of the noobs (like me ). I'm still unsure whether I'm willing to gamble right away with my Fuze next month, but I've made sure this thread is bookmarked in case I decide to take the plunge!
What should one do if using the MicroSD card method and the Olinex HardSPL says Loading... No Image File!
Coromoto said:
What should one do if using the MicroSD card method and the Olinex HardSPL says Loading... No Image File!
Click to expand...
Click to collapse
you cant flash HardSPL via microSD Card
Bricked Fuze?
I was using OliPro Rapheal Unlocker and seemed to have bricked myself. (my fault, I understand the risk) I'm not a total newbee, but first time I ran into this. Any ideas how to get past a Upgrade ROM code error? Updated from 8525 to Fuze.
lmeyers said:
I was using OliPro Rapheal Unlocker and seemed to have bricked myself. (my fault, I understand the risk) I'm not a total newbee, but first time I ran into this. Any ideas how to get past a Upgrade ROM code error? Updated from 8525 to Fuze.
Click to expand...
Click to collapse
I dont recognize the SPL version in your signature is it from Oli's Sim/CID Unlocker?
Can you explain exactly what you have done to your phone and when you bricked it please. Also can you load your Rom up or does it get stuck.
Have you tried flashing the HardSPL from Step1?
lmeyers said:
I was using OliPro Rapheal Unlocker and seemed to have bricked myself. (my fault, I understand the risk) I'm not a total newbee, but first time I ran into this. Any ideas how to get past a Upgrade ROM code error? Updated from 8525 to Fuze.
Click to expand...
Click to collapse
If you flashed the hardspl, then you should be fine and should not have done any lasting damage. You didn't read the part of the instructions that tell you that you must first flash a 1.01 version of the att radio. You can get that here:
http://www.rapidspread.com/file.jsp?id=v3q7csfizy
If you don't then you get the rom upgrade error. Just put your phone into bootloader (tri-color screen), and flash that radio. Also, as always, questions about specific roms, apps, etc should be posted in the thread they came from. That is where all the people most knowledgable about the subject are most likely to read it.
@Mskip, i think that SPL is for his 8525 not his fuze.
scotchua said:
If you flashed the hardspl, then you should be fine and should not have done any lasting damage. You didn't read the part of the instructions that tell you that you must first flash a 1.01 version of the att radio. You can get that here:
http://www.rapidspread.com/file.jsp?id=v3q7csfizy
If you don't then you get the rom upgrade error. Just put your phone into bootloader (tri-color screen), and flash that radio. Also, as always, questions about specific roms, apps, etc should be posted in the thread they came from. That is where all the people most knowledgable about the subject are most likely to read it.
@Mskip, i think that SPL is for his 8525 not his fuze.
Click to expand...
Click to collapse
oh ok lol thanks for the input scot
mskip said:
you cant flash HardSPL via microSD Card
Click to expand...
Click to collapse
I did know and realize that, and your walkthrough doesn't give instructions for that either, but rather for flashing a ROM using the mSD method.
I was referring to flashing a new ROM from the MicroSD card and getting this error message in the HardSPL Bootloader screen. The ROM image has the proper name (RAPHIMG.nbh) but isn't seen by the OliNex bootloader.
Hi guys,
Mods - first time post and im not a regular user so if im breaking the rules i apologise. I have spent hours already trawling the forums, but i am now admitting defeat and I need your help!
My Problem:
I have an x7501 SPL 1.06 0000, WM 5.0, GERMAN OS
I want to upgrade this to WM6.1 ENGLISH
I dont care what the SPL is, as long as it works, is reliable, and wont disable any standard WM functionality
I am not interested in tweaks, hulks, or other (non standard) tricks, i just want to get the device running a stock WM 6.1 rom
That said - if you guys think that going to 6.5 is the best (non beta, no risk) option, then im quite happy to go that route.
$50 reward to the first person who provides the following info IN A FORMAT THAT I CAN UNDERSTAND. im good with computers for a non pro (and can follow instructions , but this is just over my head!
I Need:
1) Link to an unlocker and instructions how to use, that will give me the required SPL (note my SPL is 1.06 - will this require two SPL flash steps??)
2) Link to a stable ROM that retains all windows functionality, and instructions how to use it.
If i find that i used two or more peoples help i will split the reward accordingly!
thanks in advance and keep up the good work!
Alan K
First you need to download the unlocker from this thread and follow instructions... http://forum.xda-developers.com/showthread.php?t=315831
This will give you SPL 1.2
Here is a handy thread with step by step instructions on upgrading your roms you should read through before beginning to flash...http://forum.xda-developers.com/showthread.php?t=429013
Unfortunately, the stock-like wm6.5 roms made by michy-prima that ran on spl1.2 are no longer hosted on any sites anymore. I can try to contact him for you and see if I can get a copy directly from him. I will see if I can do that.
Otherwise, you can change your spl to 3.5, which you might as well do anyways, as there are more roms for that spl and even the stock-like michy-prima roms were made in spl3.5 also, so if I can get those, I will get the spl 3.5 versions.
So to then change your spl to 3.5, you must have first used unlocker to make spl 1.2, then the only way that was made to change spl to 3.5 was to flash the Athena Project 4 rom, so go to this thread... http://forum.xda-developers.com/showthread.php?t=387409 and download the AP ROM V.4, unzip it, and run the flasher while your phone is connected with active-sync to your computer. This will install the spl3.5 and the AP4 Rom.
Now that that is done, you can choose any SPL3.5 ROM to flash... (make sure to only flash SPL3.5 Roms now... if need be, there is a way to go back to SPL1.2 if you need to, but there really is no reason you would need to.)
Probably the most modern rom with the most features would be the AGB Version 3.00 ROM, The Hulk one (I know you said you didn't want that, but it is the most current rom, and you can easily change the theme and wallpaper on it. This is the ROM I have on my Athena... its a nice ROM.) Here is the thread for that ROM... http://forum.xda-developers.com/showthread.php?t=614158
Just unzip the rom after you download it, and like before, hook phone up to computer and let it sync, then run the installer. You can also use the ealier AGB roms, too, if they look better to you, or any rom you come across as long as it is a spl3.5 rom.
And I will try to contact michy-prima to see if I can get one of his old clean wm6.5 roms or his stock wm6.1 roms, but I wouldn't count on me being able to get one from him. Personally I think the newer AGB ROMs are alot better and more recent and updated and would recommend using them.
Also, here is a convenient thread I just found that has links to many different builds and useful tools and guides... http://forum.xda-developers.com/showthread.php?t=397518 ... so if you want to try out a couple wm6.1 while you have spl1.2 or even after flashing spl3.5, as a lot of roms are made for both spls. Just make sure you only flash roms made for the spl that you have on your phone.
I hope this helps... if you have any more questions, feel free to pm me and I'll be glad to help. Happy flashing!
Hi Zarathustrax,
Thanks for the extensive instructions. I will be checking it this week so hopefully ill be sending you some greenbacks by Friday!
Thanks again!
Al
bigalk said:
Hi Zarathustrax,
Thanks for the extensive instructions. I will be checking it this week so hopefully ill be sending you some greenbacks by Friday!
Thanks again!
Al
Click to expand...
Click to collapse
Like I said, if you have any more questions or problems, feel free to ask here or pm me.
Sent from my HTC HD2 using XDA App
Also, if you prefer to have a winmo 6.1 ROM over the 6.5 ROM I suggested, there are links to many 6.1 ROMs in that last thread I linked. Here's the link again... http://forum.xda-developers.com/showthread.php?t=397518
MichyPrima's roms are no longer hosted, but I have heard good things about Taxists and Sogarths ROMs. You can easily try a rom and then flash another if you don't like it. Just remember, make sure to flash roms for the spl that you have. If you have SPL3.5 and want a spl1.2 rom, there are links to the tool to change back to spl1.2. The only way to go from spl 1.2 to spl 3.5 is to flash the Athena Project 4 ROM, then after that you can flash any spl3.5 you want. Let me know if you have any other questions or concerns.
Hi Zarathustrax,
just to let you know - i still havent managed to allocate time to this yet.
I havent forgotten about you, and im not pulling a fast one!
thanks again for your time and effort!
Al
Hi Zarathustrax,
In the very first step (unlocker link) Olipro says "follow the steps...."
I cant see the steps he mentions anywhere? This is one of the reasons for my original post
any ideas?
Al
Forget my last question - unlocker has the steps!
Hi Zarathustrax,
tried twice and i keep getting error 202 - "check cables....... cannot connect to phone"
I have:
1) connected and synced via active sync
2) set active sync not to sync any items except for files
any ideas?
thanks
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
bigalk said:
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
Click to expand...
Click to collapse
Hmmm... might be. I'll look into this and see if I can figure anything out.
Oh, by the way, sorry I missed your messages until now. I don't check these forums daily, so if you need to contact me quicker, send a private message to me.
bigalk said:
Hi Zarathustrax,
tried twice and i keep getting error 202 - "check cables....... cannot connect to phone"
I have:
1) connected and synced via active sync
2) set active sync not to sync any items except for files
any ideas?
thanks
Click to expand...
Click to collapse
I've been reading through the forums trying to find an answer... at what point does it show this error? Is it right away? Does the x7501 change screen at all or do anything? I think I remember having problems like this when I unlocked it years ago... but can't remember exactly what I did. Does the x7501 go to it's tricolored bootloader screen at all? It maybe is having problems installing usb drivers while it's in bootloader mode if it changes into bootloader mode when you get that error. Let me know asap so we can get this solved. Also, have you tried using another cable at all?
Putting phone in usb Mode
Try installing Enablerapi.cab before using the olipro unlocker.
Are you still on this
When you run the unlocker there are 3 steps - these are three separate buttons that appear on the flasher each time.
Can you indicate at which step you get this error? Go to this link
http://forum.xda-developers.com/showthread.php?t=378216
...IT IS IN GERMAN...but it gives very nice pics of the process...using google translate you can get some idea. BUT if you can indicate which step you were able to complete.....we can help better !
Also, what windows operating system?
bigalk said:
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
Click to expand...
Click to collapse
chappatti said:
When you run the unlocker there are 3 steps - these are three separate buttons that appear on the flasher each time.
Can you indicate at which step you get this error? Go to this link
http://forum.xda-developers.com/showthread.php?t=378216
...IT IS IN GERMAN...but it gives very nice pics of the process...using google translate you can get some idea. BUT if you can indicate which step you were able to complete.....we can help better !
Also, what windows operating system?
Click to expand...
Click to collapse
I'm kinda thinking he gave up or something.... I've pm'ed him and have been trying to get more info on his problem for a couple weeks. I think he was having the problem on the first step... and the enablerapi will probably solve his problem.
But doing all this reading and trying to solve this problem has got me to pull out my old athena and start playing with it again... it's been a couple years since I've used it... I'm on the HD2 now, dualbooting WP7 and android.... but I've gotten an interest in getting my athena set-up and working again. The athena was way ahead of it's time.... if we could get devs interested in it again and get a good android build ported over, it would make an awesome tablet/phone. I think I'm gonna try to play around with getting android booting on it, but my knowledge of linux and low-level kernel work is limited to none. The best I can do is try to put together a build with what kernels/tools are already out and working on the athena, which isn't much. I think they had it booting and got touch screen working, but not much past that.
Hi zarathustrax,
no i havent given up . was checking in regularly to see if i had any response from you but never even looked at the pms. sorry.
i have a few hours to crack into this now so ive set up on a new machine (different av and firewall) and im going to have a go.
will report back - thanks for all the additional info my man!
al
ok - so i unlocked successfully but i think i may have fcked up. when i read olipros unlocker thread its says that only step 1 is necessary, ("but if you do step 2 you must also do step 3")
as i was trying to get to spl 3.5 i presumed that i didnt need to do step 2 or 3. this might have been a bad choice.
heres what happened:
ran unlocker step 1, it worked, phone rebooted. i finished there as i wasnt sure if i needed step 2 or 3
loaded bootloader screen to check spl. spl said olipro 1.2. i though cool - rebooted phone and now its a black screen. i can get into the bootloader screen whish says:
ATHE100
IPL-V1.00
ATHE100
SPL-V1.20. Olipro
have been reading up on next steps, or how to get rid of blackscreen but no conclusive answer.
its friday so im off home - battle lost but the war aint over!
Well. I'm not an expert (my Ameo was unlocked as I bought it) but if I understand, the black screen is because the ROM on your device dont match the new SPL you have. Try to flash a new ROM (SPL 1.2, right?) should help.
bigalk said:
ok - so i unlocked successfully but i think i may have fcked up. when i read olipros unlocker thread its says that only step 1 is necessary, ("but if you do step 2 you must also do step 3")
as i was trying to get to spl 3.5 i presumed that i didnt need to do step 2 or 3. this might have been a bad choice.
heres what happened:
ran unlocker step 1, it worked, phone rebooted. i finished there as i wasnt sure if i needed step 2 or 3
loaded bootloader screen to check spl. spl said olipro 1.2. i though cool - rebooted phone and now its a black screen. i can get into the bootloader screen whish says:
ATHE100
IPL-V1.00
ATHE100
SPL-V1.20. Olipro
have been reading up on next steps, or how to get rid of blackscreen but no conclusive answer.
its friday so im off home - battle lost but the war aint over!
Click to expand...
Click to collapse
Just replied to your pm before checking this thread, so I see that you can still get to SPL bootloader screen. So, what you should be able to do now is get your phone to bootloader screen and hook it up to pc like that. Then let any drivers that are installing finish, and where it says "serial" at the bottom should change to "USB".
At this point, you can now run a custom rom installer and flash a new rom. Since you want to change to SPL3.5, you should install the Athena Project 4 ROM.
Or if you want to leave it at this SPL for a while and test out a couple WM6.1 ROMS that use this SPL, just flash one of these. Here's a good thread that lists almost every ROM available with links and says what SPL they're for... http://forum.xda-developers.com/showthread.php?t=397518
I'll do a little more research also about the screen not coming on to make sure it's not some other problem, but it probably is just the current rom isn't compatible with the new SPL.
I'm sending this post to your pm too.
Also, make sure you have the SD card and sim card removed when doing flashing. And check what radio you have on your phone... you must have atleast radio 1.50 or higher to use Athena Project 4 or most WM6.1 or WM6.5 ROMS.