Related
How to upgrade from WM5 TO WM6
To upgrade your prophet to WM6 I recommend that you first of all downgrade to the NVID version of WM5 AKU2.2 and get the latest Active Sync:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe YOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com
3. Install active sync, you might need to reboot
4. When your computer has rebooted, run the file from step No 1 . Follow the steps, remember that it can take some time and seem to stuck at 80% and higher, but just wait.
5. When you have done this, your pda will reboot. After it comes with the welcome to windows mobile screen,"Tap Here To Begin",JUST LEAVE IT. In fact don't touch your device before the next steps are finished.
6. Now download one of the WM6 versions( http://forum.xda-developers.com/showpost.php?p=1279985&postcount=1 )
7. Now find a file named Upgrade.bat,and run it.(you don't have to run Step1 of PdaMobiz or PDAViet Temp,as you have already downgraded to AKU2.2)
8. Wait until the upgrade finishes(usually takes 12-15minutes)..WAIT WAIT WAIT
9. A message will be displayed in the dos box,and it will say that the upgrade is finished etc....etc...,now you HAVE to HARD RESET,to finish the upgrade and enjoy you new WM6!
How to downgrade from WM6 TO WM5
The downgrade process from WM6 to WM5 is pretty simple. All you have to do is to downgrade to WM5 NVID and after that upgrade to the WM5 you want:
1. Download the NVID(no vendor) AKU 2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exeYOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com.. Simply search for "Active Sync"
3. Install active sync, you might need to reboot
4. When your PC is ready run the NVID file you downloaded in step1 and follow the guide, remember that it can take some time and seem to stuck at 80% and higher, but just wait
5. When its done downgrading to the NVID WM5 rom, you prophet will reset and you can upgrade to the version of WM5 you want.
NOTICE
If you use a different AKU 2.2 ROM(like PDAViet Temp),you may have two EXEs in the folder you extracted.Be careful and use the one that is made for your device:
FILENAME G3.EXE
is for G3 devices:IPL x.xx.0000, SPL x.xx.000.0 (this is shown when you reset)
FILENAME G4.EXE
is for G4 devices:IPL x.xx.0001, SPL x.xx.000.1 (this is shown when you reset)
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
How to switch or upgrade/downgrade between WM6 versions(for example PDAViet->Trueneytral)
1. First you have to downgrade to WM5 AKU2.2 using the WM6->WM5 guide(some say that you don't have to do that,but i believe that it's better to downgrade first rather than making a simple overwrite)
2. Now follow STEP 5 of the WM5->WM6 guide
Device doesn't connect to PC after flash
If your device doesn't connect to your PC after flash,just enter bootloader(press camera button+while pressing soft reset and hold,until a tri-color screen shows up),and flash the NoVendor WM5 Rom: http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe .Then repeat the whole process...
----------------------------------------------------------
KEEP IN MIND:
UPGRADING CAN BE DANGEROUS,YOU ARE RESPONSIBLE FOR THE DAMAGE TO YOUR PHONE
DO NOT RESTORE BACKUPS FROM ANY ROM OTHER THAN THE ONE IT WAS CREATED ON
THERE IS NO "BEST WM6 ROM",THE BEST IS THE ONE THAT WORKS BEST FOR YOU
(part of the guide is taken from Da9L's guide,in the WM6 Rom Collection)
I will edit/update this post soon and clean it up, ask questions in another thread, and by god please read the wiki first, 90% of the questions asked are answered in the wiki....
WM6 Upgrade Guide...reply
great info sir! thanks so much! downloading...i'll be happy to send feedbacks on this WM6 ROM! thanks again!
Thanx a lot tonydeli7 , very very good guide and a lot of ppl really needed it
Great
Thanks to you all. I have Qtek S200 and trobuled with WM6 it wonderfull guide for me thank you very much.
I need to downgrade to WM5, 'couse I cannot boot anymore. After running the setup I get an error that the device cannot be found. I have connected the S200 with the boot loader running.
Edit: Now it works on an "old" WinXP machine.
Huge Problem!!
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
dharvey4651 said:
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
Click to expand...
Click to collapse
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
I followed the instructions carefully, and my phone (Qtek S200) seemed to boot with WM6.0
However, after aligning screen, it tried to initialize the phone with some extended roms, a procedure which failed, and I had to soft reset.
After reboot, it seems to work fine.
Is it?
EDIT: Another thing I noticed is that keyboard is in THAI !!! How can I make US the default? Olso, I have Resco keyboard GR edition. Will this work with WM6?
tonydeli7 said:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Click to expand...
Click to collapse
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
yoda_143 said:
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
Click to expand...
Click to collapse
i don't know mate.i believe you can use pdaviet's temp instead of aku2.2 nvid...
Another thing I noticed, is that it looses pairing with my bt handsfree...
I am making the pairing, and works fine. However, when at night I am shutting off my hf in order to save battery, the next morning the pairing is gone.
Any solution to this?
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
dufchan said:
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
Click to expand...
Click to collapse
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
I-mate Jamin
hello evrybody
i just wanted to know if i can upgrate my WM5 to WM6 on my I-mate JAMin?
rondol1 said:
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
Click to expand...
Click to collapse
thank u very much!!now my dopod working fine!!thanks a lot!!
thanx for the guide
help me please..
P4k1t0 said:
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
Click to expand...
Click to collapse
how to do that?
thx..
Choice of ROM
Hello guys, tanks for a so nice job !
I would like to have more information about the choice of ROM.
I don't want any special feature, just the row wm6.
no programs added, no tweaky today, no bugs, no battery problem, etc etc
which one would fit that the best ?
thanks
Thnx for this man, much appreciated!
hey))) as promised, the Soft-SPL and Hard-SPL
1. Soft SPL - loaded to ram temporarily, erased after reboot, use it to flash HardSPL or tested working roms.
2. Hard SPL - A version which is flashed to rom.
So, what`s this?
1. Based on oxygen spl, but
1. Doesn`t check CID
2. KeyCard security is reset
3. Allows to flash unsigned (custom) nbh files.
http://rapidshare.com/files/65732449/hspl.7z.html
Instructions:
1. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen
2. Connect USB to pc
3. From the flasher folder run ROMUpdateUtility.exe and follow instructions to flash the Hard-SPL if needed. or you can flash *ANY* oxygen rom
4. After flashing Hard-Spl, to avoid reflashing, use
nbhextract ruu_signed.nbh
with any official update.it will dump the nbh. you`ll see some file like 00_OS.nb0 or 04_OS.nb0, any *_OS.nb0
use Htc Rom Tool (can be found on forum) and go to build rom, select OXYGEN, use 1.0.000.0 version, and go to system box, and press "..."
Load your os.nb0 and press build rom. then you can use this nbh to flash os. just replace original nbh file within updater directory.
p.s. sorry, have problems with wm6 - no info when i`ll finish it
Good Jobs :d
THANX SPV3DEV foor tool . WM6 for tis device ?
THANK YOU GREAT JOB. not tested yet. but thanks for the efforts.
how is WM6 comming as you promised?
sp3dev,
Thanks I have CID unlocked my phone.
Please I need to SIM unlock it.
how I can do it?
Please help.
Doesn't work for me.
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
quell said:
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
Click to expand...
Click to collapse
You passed in boot mode? Long push camera and short power.
No...I didn't pass. Phone has white screen, when I run RomUpdateutility.exe before flashing shows me error.
Have ideo when your WM6 rom will be finish ?
Thx for the tool , great job .
wm6
HI. Please Guide coking rom for Htc S310? Thanx
quell said:
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
Click to expand...
Click to collapse
I've this problem too. Running windows vista aswell. Anyone found a solution?
RUU on vista
the solution is here:
http://www.modaco.com/content/Windo...U-on-Vista-It-can-be-done-the-ultimate-guide/
Hello all
my phone is fully unlocked
i soft-spl my orange c100(htc 310) and when i tried to hard-spl it just crashed wile writing the new spl
now i am stuck at tri-color boot screen
Does somebody have orange c100 romania rom?
Thanks
Maybe you will help me...
sp3dev said:
4. After flashing Hard-Spl, to avoid reflashing, use
nbhextract ruu_signed.nbh
with any official update.it will dump the nbh. you`ll see some file like 00_OS.nb0 or 04_OS.nb0, any *_OS.nb0
use Htc Rom Tool (can be found on forum) and go to build rom, select OXYGEN, use 1.0.000.0 version, and go to system box, and press "..."
Load your os.nb0 and press build rom. then you can use this nbh to flash os. just replace original nbh file within updater directory.
[/QUOTE=sp3dev]
Hello!
Maybe you Sir have an official Oxygene ROM image? Maybe you dumped it for yourself before all thos updates? I am extremally looking for it Please let me know if you could send it or upload somewhere.
Best greetings,
RA
Click to expand...
Click to collapse
Hi,
Where do I place hard spl?
When pressing this I first press camera and then open spl.ink ? Or is there another way I should do this?
i am from romania and i have spv c100.
if you could tell me how to back-up my rom i will help you.
hi SP3DEV
in step 1. "Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen" how do I do this? I copied the 3 mentioned files to root directory but how do I hold the camera and launch spl.lnk at the same time. Please explain this thoroughly. I just bought an HTC S310 and want to upgrade my toy. Thank you much
charlietruong said:
in step 1. "Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen" how do I do this? I copied the 3 mentioned files to root directory but how do I hold the camera and launch spl.lnk at the same time. Please explain this thoroughly. I just bought an HTC S310 and want to upgrade my toy. Thank you much
Click to expand...
Click to collapse
same problem.. any solution?
Cease & Desist!
Hard-SPL is *MY* trademark, I never said you could use it.
PSYCHE!
just kidding, but tell me sp3dev, when you disasm the SPL; are you actually rebasing the file, or just going at it by trial and error... because it shouldn't take more than 5 minutes to hack up a Hard-SPL and SSPL.
Also... really you should only call it Hard-SPL if it prevents itself from being overwritten, otherwise it's just a USPL... not that I particularly mind.
I was trying to make upgrade from wm5 to wm6,and was looking in tutorial xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide. First,I found a Upgrade_HardSPL_G4.rar, and did what was said in tutorial,copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,Execute the SPL.lnk IN THE DEVICE, then you see Prophet in all bright or white screen,Execute the ROMUpdateUtility_NV_G4 (I have a g4 device) to upgrade hardspl. I got message that my update utility was old and that I need new. Then I restarted device,just run ROMUpdateUtility_NV_G4 from the hardspl folder and instalation went smooth,pda restarted and worked well. Then I went back on xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide,found this sentence: ''Step 3 and 4 are necessary only if the WM6 rom you have downloaded instead of nk.nbf has os.nb file and the ExtROM folder'', and as I downloaded wm61_korand_3_1.rar that contains only nk.nbf file,I put it in Update_Package\Update Utilities,and run ROMUpdateUtility_NV_G4 fron that folder. The instalation finished and pda booted in bootloader. After that I tried flashing Shadow My Edition 2,no DualSIM,and followed the instructions to recover pda from wiki/ prophet recovery(downloaded PDAMobiz_Prophet_WM6_V1.00_Step1),everything was the same,always bootloader. Is there a help for my prophet? Could someone give me a step by step istruction how to bring it to life? Any help is welcome. Thanks
What is the IPL/SPL displayed?
Are you sure your device is a G4?
Try a hard reset.
Try this again: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
IPL 2.58.0001
SPL 2.58.0001
I'm sure that my device is g4. Did a hard reset and it went to bootloader again. Is there a hope? I will try http://wiki.xda-developers.com/index...ophet_recovery, but I noticed that when I run RUU and after verificatio informations on my pda it shows image version :_____________(blank),,then I click update,and then it shows
From:
image version :
To:
image version :
there is no numbers.
If you can enter bootloader, the device is recoverable.
HardSPL???
nikolah said:
I was trying to make upgrade from wm5 to wm6,and was looking in tutorial xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide. First,I found a Upgrade_HardSPL_G4.rar, and did what was said in tutorial,copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,Execute the SPL.lnk IN THE DEVICE, then you see Prophet in all bright or white screen,Execute the ROMUpdateUtility_NV_G4 (I have a g4 device) to upgrade hardspl. I got message that my update utility was old and that I need new. Then I restarted device,just run ROMUpdateUtility_NV_G4 from the hardspl folder and instalation went smooth,pda restarted and worked well. Then I went back on xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide,found this sentence: ''Step 3 and 4 are necessary only if the WM6 rom you have downloaded instead of nk.nbf has os.nb file and the ExtROM folder'', and as I downloaded wm61_korand_3_1.rar that contains only nk.nbf file,I put it in Update_Package\Update Utilities,and run ROMUpdateUtility_NV_G4 fron that folder. The instalation finished and pda booted in bootloader. After that I tried flashing Shadow My Edition 2,no DualSIM,and followed the instructions to recover pda from wiki/ prophet recovery(downloaded PDAMobiz_Prophet_WM6_V1.00_Step1),everything was the same,always bootloader. Is there a help for my prophet? Could someone give me a step by step istruction how to bring it to life? Any help is welcome. Thanks
Click to expand...
Click to collapse
would you mind to read me thread?
dioxda2,I read your thread. and I will now try a other hardspl that you linked there. Was that the remark you wanted me to come to my notice?
Same Issue
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
georgexavier said:
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
Click to expand...
Click to collapse
there are sucessful cases , please read my post or.... are you using Vista?
If so, you need other solution. (not with me ... sorry ~~ )
georgexavier said:
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
Click to expand...
Click to collapse
What is the SPL of your device?
When recovering to WM5 you better NOT use the Mobis step 1. Any other step 1 or NVID will be fine. The Mobis ROM is too manipulated for flashing their own WM6 ROM. It will give all kinds of problems when it is used for other purposes.
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
nikolah said:
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
Click to expand...
Click to collapse
see my thread la~~~~
dioxda2,I have read your thread. This is what I know at the moment,and what I think it should be done (correct me if I make any mistake):
-my pda boots in bootloader mode
-it shows on screen IPL:2.58.0001, SPL:2.58.0001
-it's G4 model
-it has no hardspl on it
First one wild shot:
1. Download this jumpspl http://forum.xda-developers.com/showthread.php?t=329147
2.follow the instructions,and instead nk.nbf file from desired rom I put a nk.nbf file found in hardspl rar archive to the SoftSPL folder ,and hopefully flash hrdspl.
3.from bootloader flash any desired wm6 rom with RUU
Second solution:
1.download PVTemp
2.try to flash it from bootloader
3.if it's ok,then on to the next step like on your page one for old method.
Is there something else,diferent way to do this from bootloader?
Thanks for all help
In bootloader, try to flash this: ftp://xda:[email protected]/RUU_Prophet_220734_2207114_024721_NVID.exe
nikolah said:
dioxda2,I have read your thread. This is what I know at the moment,and what I think it should be done (correct me if I make any mistake):
-my pda boots in bootloader mode
-it shows on screen IPL:2.58.0001, SPL:2.58.0001
-it's G4 model
-it has no hardspl on it
First one wild shot:
1. Download this jumpspl http://forum.xda-developers.com/showthread.php?t=329147
2.follow the instructions,and instead nk.nbf file from desired rom I put a nk.nbf file found in hardspl rar archive to the SoftSPL folder ,and hopefully flash hrdspl.
3.from bootloader flash any desired wm6 rom with RUU
Second solution:
1.download PVTemp
2.try to flash it from bootloader
3.if it's ok,then on to the next step like on your page one for old method.
Is there something else,diferent way to do this from bootloader?
Thanks for all help
Click to expand...
Click to collapse
Hi there ~~~~ tell you what~~ ^_^
1. there are 2 ways to upgrade
a. " New " Method.
b. " Old" method.
2. for more update rom flashing.... better have you device hardSPL.
then you can go by 3 means to flash....
1. straight upgrade that is: connect to PC via activesync, activate RUU right ahead ( I don't like this method as sometimes will stuck @ bootloader,
2. copy the 3 files from the jumpspl to the prophet's root directory then activate manually...
3. force bootloader ( by manually buttons combination and not reboot in 3 color hang )...
then 2 and 3 is fine, ( 3 is more convenience though), you should see " USB " at the bottom prophet screen if you did things right. ^_^,
then flash...... ^_^
This is my [size=+2]little handmade tool [/size], a combination tool with Taiwan Cook - YouZii and XDA cook - Korand,
just unzip, execute the " UPGRADE.cmd " , the some on screen clicks, wait and done. !!!
Don't forget to hardSPL before so. OK?
Enjoy ~~~
A Batch flashing tool and Korands clean rom 3.1... Check it out ! ^_^
P.S. Connection Error? Please try again ~~ ^_^
nikolah said:
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
Click to expand...
Click to collapse
You will find it here:
ftp://ftp.xda-developers.com/Uploads/Prophet/Prophet-roms/
Hello did somebody know from where i can download original WM 6 or 6.1 ROM for HP IPAQrw6815-not modified?
thanks
Teodor
[email protected]
hp doesn't come out with WM6 or WM6.1 for ipaq 6815.... there's only custom roms which are modified to work with ipaq 6815... you can choose from a variety of them in here.... have fun!...
thaks for this
Help with My ipaq 6815
Nhocbanme hi,
i've read thru many of the replies in this forum. i'm a newbie and don't knw much abt roms. i tried upgrading or if u call it flashing my ipaq via PC and later SD. the PC flash did not work. i had to wait almost the whole day becos it said it was reading configuration from the phone. i later tried the flash via a transcend 1GB miniSD and till today the phone has gone off. i tried to power it on even with th e battery fully charged. my sis has the same phone i tried swapping batteries but it still didn't come on. i really need to upgrade to windows mobile 6.1 i formerly had WM 5.0, today itried again and it still stays on the boot screen.(white background with the HP logo and the Pbl 1.05 at the botton of the screen .
please i need help ASAP.
Downlgrade your bootloader to 1.01
Hi,
You have to downgrade your bootloader from 1.05 to 1.01. Find in the following the instructions how to do it. I did it and it's working.
Be careful when you do downgrade, because you can end up without phone
Quote:
How to flash from PC with Windows XP (It is ok to run it in vmware)
Thanks Knave and rcperez for posting their detailed experience so I can write this section. Also thanks jimmyspa for improving the addheader's performance greatly.
1. Check your Boat loader version
(do a soft reset, and check the value printed at the bottom during the HP logo screen)
2. If you noticed that the last line states BL 1.00.05, it means you have boat loader 1.05 installed. You will need to download and flash your phone back to 1.01 via ftp://ftp.hp.com/pub/softpaq/sp34001-34500/sp34053.exe (VERY DANGEROUS, FLASHING VIA SD IS MUCH SAFER!)
3. After successfully downgraded your phone's boatloader, or your version was already v1.01, you can proceed to flash your phone to the rom.
With the check done, proceed with the required files.
1. Go to download section to download the rom file. -- The rom that you downloaded, e.g (diskimg.nbo)
2. Download the file pcupdate.zip attached in this thread and unzip the contents to the same folder you used in step 1.
3. Download the latest Rom file and extract to the same folder
4. Run BuffereAddHeader.bat. It will take seconds to generate a diskimage_Ver.nb0. (You should have Java Runtime > 1.50 installed, http://www.java.com/en/download/manual.jsp)
5. Move your phone to boatloader mode ( press the two - keys, follow by a poke at the soft reset hole with your stylus )
6. Connect the phone to the PC
7. Execute the Device Utility Update program and wait till it verifies the state. Click on Update Item "All" use cursor keys to change it to "OS ONLY" then hit next **** SELECT "OS ONLY", if you cant change it to "OS ONLY" DONT PROCEED!!! It should detect your device as Model 0 etc.
8. Press Next to begin flashing.
9. Once completed, the phone will reset by itself. Wait for a while for it to startup.
REMEMBER SELECT OS ONLY BY PRESSING DOWN IN THE SELECTION BOX
Here are the notes & files provided by hochengsoon with README for flashing via Windows XP
PC flashing using BL1.0.1 must be done from C:\Windows\Temp, so why not start everthing from this folder ie PCUpdate + ROM + missing file(s).
PCUpdate1.rar - http://www.mediafire.com/file/k5jumzzg1mm/PCUpdate1.rar
How to downgrade to WM5 using PC
1. download wm5 rom from http://h20000.www2.hp.com/bizsupport...pappid=NextGen
2. run it and after entering the updating screen cancel it.
3. replace the hpRUU.exe in c:\IPAQ(default install) with the attached file hpRUU.exe in archive hpRUU.zip
4. Connect device to PC, then press and hold two "-" button and reset.
5. Run hpRUU.exe and do a normal update.
Note: you may delete eboot*.nbf to prevent bricking the device.
bootloader missing
well i m using HP rw 6815, n last night i had flashed a 6.5 rom , later i was unsatisfied with tat rom,
so i went 2 change it, n during tat process, my phone turned off, n now it doesnt switch on, 1ce i managed 2 go 2 boot screen thr i cud see hp logo n bl-0.0.0 can ne1 help me out with it, how do i put bootloader in phone.. neither my pc detects the phone... help appriciated
HI i had same problem on hp rw6815
No bootloade aparantly but bootloader hp logo loaded but insted o o.0.o i had a ff.ff.ff bootloader. i dunno what that meant. i inserted a eboot.nb0 on sd reseted in bl (v1.0.5 from this forum).... bootloader updated oki.. but my phone transformed in a hp rw6828, and i can install 6828 rom working and bootin fine in rw6815, the rw6815 rom install via sd but restarts on boot screenn .. this appeard when i tried a downgrade from wm6.5 to wm5 when i try to upgrade via hpruu it looks tat i have a no language hpipaq model.. My model info is "€ R 0 6 0 8 2 2 N _ M N 1 A R C _ R S 0 0 0 5 2" i dont know how to interpret this file sysyinfo.txt with that data. my question is how can i downgrade to wm5 and original bl of hp rw6815? i have all files in nbf form. The onli soluton to the problem if ur phone restarts after rom upgrade downgrade on witn wm 6.5 an 1.01 bl is the atrached rom.. workin 6815-camera-patched-R3.zip is the only rom... located here http://forum.xda-developers.com/showthread.php?t=360664 second post under orher roms
6815 camera patch may work version r2: http://www.mediafire.com/?lihy0vcvnxd
6815 camera patched version R3: http://www.mediafire.com/?2mjhtgjox0x
This roms get ur phone alive after this bug... or the restar bug... they work with both 1.0.1 bl and 1.0.5 bl more stable with 1.0.1... and i thing the developer of the rom did not change the indentifier of the rw6828 rof for 6815... i think it;s hybrid rom between... it works.
Plese help me to downgrade to original state... hp rw6815 bl 1.0.5 rom wm5. or help me solve the hpruu problem... not patched for model and lang beacouse it says the same incopatible thing.. the picture is the same result in patched and original ruu.. .
me too
i got that same problem i dont know wahta to do help guys
bootloader missing after Upgrading to wm 6.5
Hi Dear, i had the same problem but the solution is so funny.
1. Remove Battery from your mobile.
2. Remove SIM card too.
3. Wait around 5 min. & put them back again.
4. Everything should be OK
I hope Problem solve like me , But realy i don't know why ??? .
Best regards, Jalal
I tried to flash the 6815 is here and I have put my diskimg.nb0 on 2gb memory card. Press the 2 buttons with the "-" and give it to reset with a stick ... I get into the bootloader and returns to the screen while windows. It might be because the bootloader has the pda is 1.0.5??
The problem is that trying to change the bootloader 1.0.1 is here and not working because my pda is Spanish.
How can I reduce it?
Dear SHKUMBIN,
I am very grateful for the clear and beautiful explanation, which indicates that a great effort and considerable experience and also " NHOCBANME " and " ARIEY " for the great job they do to bring those custom rom's.
Accept my greetings.
karamzak
Hello Everyone!
This is a step by step guide for unlocking the SPL of your HTC P3400 or P3400i.Please read and follow everything given here carefully and you will have your phone unlocked within 15 minutes.
This is a step taken in order to minimize the accidental bricking scenerios happening almost everyday here.
The Guide is divided into 2 Parts, A FAQ section and the Unlocking Guide Section. I request you to please read all of this before doing any furthur steps. ROM Flashing can be very dangerous if not done properly.
Enjoy!
Frequently Asked Questions
FAQ (Frequently Asked Question) Read Carefully Please
Q1. What is the basic information about my phone that i would need to get started with this process or for troubleshooting?
Ans. The basic information that you need is displayed on the white htc splash screen that shows up when you start your phone. This inludes:
ONBL version, SPL version, GSM or Radio version and OS version.
Apart from that, you will also need the serial number of your device. This can be found behind the battery on your device or on one side of the packaging box in which your device came.
An optional thing that may come handy is the version number of your ROM which can be found by going to Start > Settings > System > Device Information. Look for the ROM Version there.
Q2. What is SPL, Why it needs patching, and what are the things i need to keep in mind?
Ans. SPL or Second Program Loader is a part of your phone's firmware. Its responsible for both loading of operating system and it is also used by operating system for some low level tasks. By Default, HTC and Other Manufacturers too, design it in such a way that it does not allows custom ROMs to be flashed in the phone. It does no by checking for the Digital Signature of HTC on roms. So it need to be patched in order to flash custom ROMs made by chefs in this forum.
There are two SPLs available right now for P3400 and P3400i. One is Olipro's SPL for Old Gene and Second is Orefkov's SPL for New Gene. These should be used according to the device they are meant for. Using wrong SPL can make your device dead.
One more thing is, SPL is needed to be updated just once. Only one of the given SPLs will work for you and you will never need to patch it again. This is true for those situations too when you flash a rom and your phone does not boots past the White HTC splash screen. In that case too, As you have just flashed an incompatible ROM, you just need to use another, compatible ROM to get your phone back. NEVER UPDATE YOUR SPL ONCE IT IS PATCHED BY EITHER OF THE METHODS
Q3. How can i be sure which version i need to use, i am not sure whether i have an old gene or new gene?
Ans. Earlier it was being thought that one can differentiate between New Gene and Old Gene on the basis of Onbl and Serial Nos. But this has not found to be true as evident from many cases of bricking.
One of the possible checks for knowing that is if your phone originally came with Windows Mobile 5, its probably an old gene, and If it came with Windows Mobile 6, its probably an New Gene. However, this is also not a concrete basis to decide the version of SPL.
So i recommend to follow these steps, These should work for any Gene without problem.
1. Use the Olipro method first. It will work properly if your device is an old gene.
2. If it fails and your phone becomes dead, just follow the instructions for using Gene Unbricker for new gene and your phone will be back again. This way, your new gene will be flashed with Orefkov's method.
Q4. Are there any precautions that i need to take when selecting a ROM for flashing to my device?
Ans. Yes, there are indeed some things that you need to keep in mind before making mind to flash a ROM.
1. Make sure your SPL is patched, ie. On boot screen it should have either SPL 1.10.Olip displayed in case of an old gene OR SPL 1.07.Oref in case of a new gene. If it is not, patch it using the Guide given below. If it is, dont ever try to patch it again.
2. After patching your SPL you will become sure that whether your phone is a new gene or old, because of knowing the version of SPL that worked for you. Now, never choose a ROM which is not built for your phone. Only use ROMs appropriate for you phone. And if you ever accidently flash a ROM of wrong version, dont panic. Just flash another ROM for your version and your phone will be back.
3. In general, never try to downgrade your ROM. Means if your original ROM was WM 5 and you upgraded to WM 6 or 6.1 Dont try to downgrade to WM5. This is specially true for WM 5 because of reasons i'll explain later.
Q5. Why is it not recommended to downgrade the OS version, ie. moving to a previous ROM version?
Ans. There is no problem actually in doing so. But there are some situations that needs to be taken care of. What happens is, Somtimes, the previous version of Original ROMs from htc, contain the older version of SPL that is very specifically made for that version of ROM.So if you flash this ROM, your SPL will again become locked. This is specially true for original WM 5 ROMs
In case your phone came with WM5 originally, and the version of ROM exactly with the one that was originally on your device, It wont give any problem. But if this ROM is not exactly the version your phone originally came with, this will brick your device and you'll have to take it to service center. No homemade solutions works then.
Even bigger problem arises when your phone came with Wm 6 originally and you try to downgrade it to WM 5. This will certainly brick your device and force you to take it to service center. SO DONT EVER TRY TO DOWNGRADE A GENE TO WM5 IF IT ORIGINALLY CAME WITH WM 6.
ROMs created by users here do not contain the ONBL, SPL and GSM parts (dont worry about the names). These only contain the OS part which is safe to use.
Q6. What are the things i can try if i get a problem while this process?
Ans. You shouldn't get any trouble if you take all the precautions, but even if you do, you can try :
1. If your gene is bricked by Olipro SPL, use the gene unbricker for new gene by Orefkov.
2. If you flashed your phone with a ROM made by some user on this forum and it doesn't works, just flash another version of the ROM or some other compatible ROM. NO need to touch anything else.
3. If you downgraded/Upgraded using any of the Original HTC ROMs and your phone is bricked, try the JTAG Method by Orefkov. Search for it, you'll easily find it. If even that doesn't helps, Take your device to service center.
Q7. What is bootloader mode, and how do i enter it?
Ans. Bootloader mode is a special mode which is use to flash ROMs. Bootloader is the part of your phone's firmware that kicks in even before SPL and initializes it. You may need to enter this mode while patching your SPL or sometimes while flashing a ROM. To do that, Shutdown your phone, Press and Hold the Camera Button and press the power button or the soft reset key using your stylus. This will take you to a 3 colored screen with your Onbl and SPL version displayed on it. This is called the Bootloader mode.
Q8. What is Hard Reset and Soft Reset and how to do it?
Ans. Soft reset is a second name for restarting your phone. It can be done using power button too but sometimes, when the phone is hanged, it needs to be done by pressing the soft reset key, situated in a small hole near the mini usb port you use for charging and headfone, using your stylus. Your phone will restart immediately without any harm. But if you have any unsaved data, like an open, edited word file or a text message half written and not saved, they will be lost. But all your saved data is safe.
Hard reset is something that needs to be done when there is some problem with the phone that is not being solved using any standard method or restarting the phone. This method erases all the files and data in phone memory (not SD card) and makes your phone as it came new from factory or just after a fresh ROM upgrade. You'll loose all your emails, calender items, Todo list, sms, contacts etc. But most of the problems get solved using this. So before using this, backup your PIM data using utilities like PIM Backup by dotfred etc.
To do a hard reset, shutdown your phone, Press and hold the two soft keys (the keys above the call accept and call reject keys) and press the reset button using stylus. A black screen will appear warning you about the consequesnces. Press the Green key (call accept key) to start the process.
The Step By Step Guide
The Step By Step Guide
CAUTION: DO NOT UPDATE ROM OF A PHONE THAT IS SIM LOCKED. THE RESULTS ARE UNKNOWN BUT MOST OF THE TIMES IT PREVENTS YOU FROM USING THE PHONE ANY FURTHUR!!
If you like to backup your existing rom first, follow this guide by Ankit360 to do it : http://forum.xda-developers.com/showpost.php?p=3215838&postcount=20
Step 1: Download the Tools
-------------------------------
Download the tools zip file from here:
http://www.4shared.com/file/81084740/fa599d63/SPL_Unlocking_Tools.html
Its a self extracting file, just start it and give a path and it will unzip all the files in your chosen folder. Inside the extracted folder you will find these things:
1. SPL Updater : Inside it there are 2 folders, Olipro and Orefkov. These contain the two SPL patchers that we need to use.
2. ROM Update Utility : This contains the ROM update utility we will need to flash a ROM. Unzip it into a folder.
3. USBDriver4ActiveSyncVista : This contains a special driver for Windows Mobile Device Center in Vista that you need to use to successfully update your ROM. Unzip it in a folder too.
4. Download a ROM appropriate for your device: Which one is appropriate, you'll only know after updating your SPL. So do this step after that. But in any case, here is a link to a good ROM, created by me, which is available for both new and old gene:
Sumit's Pro Users ROM (WM 6.1, for new and old gene)
http://forum.xda-developers.com/showthread.php?t=467796
Step 2: Preparing your phone
--------------------------------
1. Copy the file gene_hspl.exe from the SPL Updater\Olipro folder that you got in step 1 to the phone memory.
2. First, on your phone, Go to Start > Settings > Connections > USB to PC. Here, uncheck the checkbox : enable advance nerwork functionality. Click OK. Disconnect and Reconnect the USB cable to your pc.
Step 3: Prepare your Computer (Please pay attention, this is crucial!)
--------------------------------
XP Users
----------
There is not much you need to do. Just open task manager and kill the Active Sync executable from the processes tab. Its named as wcescomm.exe.
Vista/Windows 7 Users
-------------
You need to take these steps :
1. Go to desktop, right click Computer, and select Manage. Go to Device Manager. Now under the section Mobile Devices, Double Click : Smartphone USB Sync.
2. On the Drivers tab, click "Update Driver..." button. On next screen click : "Browse my computer for driver software".
3. Click : "Let me pick from a list of device drivers on my computers". Click "Have Disk.." on next screen. Click "Browse..." and go to the folder extracted in step 1. There, go to USBDriverforActiveSyncVista folder. Here select the file "wceusbsh.inf" and click OK.
4. Click Next and finish the wizard.
NOte : YOU NEED TO DO THIS TO SEE THE "USB" BUTTON IN MTTY WINDOW IN LATER STEPS. DONT SKIP IT!
Step 4: Use the Olipro method first.
-----------------------------------------
Open File manager on your phone. Go to the location on phone memory where you saved gene_hspl.exe. Tap on it to run it. Your phone will restart after a short pause.
Now there are two chances :
a) If its done alright, you'll see SPL 1.10.Olip on your boot screen and your phone will boot just fine. And it confirms that you have an old gene. You do not need to do Step5. Proceed to Step 6.
b) If it doesn't boots, and only green and red keys blink, Don't worry. Your phone is bricked but you'll get it back using orefkov's method in a minute. Proceed to next step. And this confirms that you have a new gene.
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
Step 7 : Set your PC and Phone back to normal
------------------------------------------------
This step is only needed in case you are using Vista.
The driver we updated in Vista will not work for normal active sync operation. So you'll need to set it back to the original version. There are two ways to do that. Either, uninstall and reinstall the Windows Mobile Device Center Or Follow the same procedure gicen in Step 3 but instead on clicking the "Have Disk button", choose the driver from the list already given.
The driver that you need to install can be identified by have a newer version given in front of its name. Also, the newer driver's name includes "Microsoft Corporation" while the older one has only "Microsoft".
You can Put back your SD card now.
On your phone, again go to the Start > Settings > Connections > USB and check the checkbox there and click OK.
That's it! You are Done.
Credits
Thanks to these people whom work helped me greatly in writing this Tutorial:
Ankit360 for writing the original tutorial.
Olipro for providing the SPL for old gene.
Orefkov for providing the Gene Unbricker for New GENE.
Nevermind_me for sharing his real experience as an end user and help in updating the guide.
NEW BEE
The info being provided is very informative,there is no way i can go wrong with these steps.hope it helps unbricking my phone.thanks to the people involved for making it happen.you guys rock.gonna try these steps will let you know if i got it rite.
your fellow new bee
I TRIED THE SUMMITS STEP B STEP GUIDE AT THE POINT WHER MMTTY PROG SUPPOSE TO MAKE SCREEN ON PHONE GO WHITE IT GIVES ERROR MESSAGE SOMETHING ABOUT CAN'T DOWNLOAD IMAGE,OR SOMETHNG
My P3400i SR8XX is OLD or NEW?
Hi! Crazy & Ankit,
I am from Delhi and having P3400i with SR. HT8XXXX, onbl-1.17.000,spl-1.17.000,os-1.8.00.
In the past I have flashed several times of cooked rom by chayn & lomlom without changing to permanent HSPL. It was done by temporary CID unlock method as running jumpsp.exe while pressing and holding Camera+VoiceReco button and flashing. Presently we are using Vista Design build 20270 by Chayn and and still my onbl& spl displays 1.17.000.
Today I tried to flash Ankit M2D rom using previous method, flash completed successfully, device restarted but stuck on boot loader. Then i restore my Gene by RUU_Gene_hTC_Asia_India_1.17.720.1_4.1.13.34_02.79.90_Ship and then flashed Chayn Vista Design 20270 which is working fine.
Please confirm whether my Gene is NEW or OLD as if it were NEW then Ankit's ROM Should work. Sorry for my bad english.
Thanks..........
Yours is an old gene i guess. Using Serial No, ONBL and SPL versions for recognizing your phone as a new or old gene is not reliable. chyan and lomlom's both have provided some excellent roms for both new and old gene so i cant say about that also. But ya, if Ankit's ROM is not working then yours is an old gene, i am 99% sure.
Thanks for your quick response to our query. Further, could you please advise me better ROM for me to Flash.
Also, I have created 1% increment battery dll and tested on my gene which is working fine. Is it possible to include it in your ROM.
@krazy
Oh Boy! Now we have an old Gene (3400i) with 8 series number and 1.17 onbl. Great going HTC !
Guess you have some really busy time coming up.
BTW:
Do you know typing? Better learn it soon .
What to say brother, HTC is just making things difficult, i guess they want to sell the higher end mobiles too. But i dont understand, apart from WinMo 6.1, their higher end mobiles have faster and greater hardware. So how come flashing a gene with WM 6.1 and Manilla 2D can affect their sales? I wont go for a P3400i if i had the money to buy a diamond even if both of them can/already have WM 6.1.
I know typing very well, you might have got some idea from the amount of text i post when i post a new rom I am ready, give it to me baby! Yeah! LOL!
qasidakbar said:
Thanks for your quick response to our query. Further, could you please advise me better ROM for me to Flash.
Also, I have created 1% increment battery dll and tested on my gene which is working fine. Is it possible to include it in your ROM.
Click to expand...
Click to collapse
Hey man, its really nice! Love it. Will include it in ROM is some more users gave positive responses, as you know that the ROM is not for somebody alone, its for the community. So will have to take some feedback before including. I'll post it in recommended downloads section in both of my roms. Thanks for it mate
krazy_about_technology said:
Yours is an old gene i guess. Using Serial No, ONBL and SPL versions for recognizing your phone as a new or old gene is not reliable. chyan and lomlom's both have provided some excellent roms for both new and old gene so i cant say about that also. But ya, if Ankit's ROM is not working then yours is an old gene, i am 99% sure.
Click to expand...
Click to collapse
You are 100% right, my gene is absolutely OLD. I have downloaded and flashed your OLD Gene 1.04 rom and it is working fantastic. Thanks again your are really the Crazy Sumit.
Yeh, I know I am Krazy, but Krazy with a K not C! Got it
Rom in PTG
Hello staff of the forum can be a rom in PT to Gene 100 HTC P3400?
thanks
Phone Info:
S/N:SZ71xxxx TMN ONBL: 1.07.0000 SPL: 1.07.0000 OS:1.7.0.0
puto116 said:
Hello staff of the forum can be a rom in PT to Gene 100 HTC P3400?
thanks
Click to expand...
Click to collapse
There are no 'staffs' in this forum, we all are members just like you . Please elaborate your phone details (the details your device shows when you switch on), then someone will be able to help you out.
@qasid: The battery bar did not show up in my Gene in the top bar . Using a manilla2D version. any ideas?
@shaunak! Have you tried sdkcerts patch, I think it will solve the issue.
qasidakbar said:
@shaunak! Have you tried sdkcerts patch, I think it will solve the issue.
Click to expand...
Click to collapse
Yup! its already installed, since I am using color icons. Can you please post a screen shot ?
Rom in PTG
sorry
Hello staff of the forum can be a rom in PT to Gene 100 HTC P3400?
thanks
Phone Info:
S/N:SZ71xxxx TMN ONBL: 1.07.0000 SPL: 1.07.0000 OS:1.7.0.0
Addicted2xda said:
Yup! its already installed, since I am using color icons. Can you please post a screen shot ?
Click to expand...
Click to collapse
Please see post#8 for screen shot.
backup orignal rom
to bauckup orinal rom orefkov created small programm for it.
Programm dump_gene_os_extrom.exe do dump os and extrom from Gene to memory card. Created files are identical os.nb and extrom.nb, extracted from official RUU_Signed.nbh, and allow rom coocking with it.
Usage:
Copy dump_gene_os_extrom.exe on your device. Insert SD-card with at least 70 MB free on it. Run copied program. After some time you will see message - Dump complit. On SD-card will be files os.nb and extrom.nb.
how to flash ?
use htc rom tool
click on build tab
device = gene
u see firmware contain on right
give path Ext. ROM to extrom.nb
OS to os.nb
click on build u get new file called ruu_signed.nbh