Related
How to upgrade from WM5 TO WM6
To upgrade your prophet to WM6 I recommend that you first of all downgrade to the NVID version of WM5 AKU2.2 and get the latest Active Sync:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe YOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com
3. Install active sync, you might need to reboot
4. When your computer has rebooted, run the file from step No 1 . Follow the steps, remember that it can take some time and seem to stuck at 80% and higher, but just wait.
5. When you have done this, your pda will reboot. After it comes with the welcome to windows mobile screen,"Tap Here To Begin",JUST LEAVE IT. In fact don't touch your device before the next steps are finished.
6. Now download one of the WM6 versions( http://forum.xda-developers.com/showpost.php?p=1279985&postcount=1 )
7. Now find a file named Upgrade.bat,and run it.(you don't have to run Step1 of PdaMobiz or PDAViet Temp,as you have already downgraded to AKU2.2)
8. Wait until the upgrade finishes(usually takes 12-15minutes)..WAIT WAIT WAIT
9. A message will be displayed in the dos box,and it will say that the upgrade is finished etc....etc...,now you HAVE to HARD RESET,to finish the upgrade and enjoy you new WM6!
How to downgrade from WM6 TO WM5
The downgrade process from WM6 to WM5 is pretty simple. All you have to do is to downgrade to WM5 NVID and after that upgrade to the WM5 you want:
1. Download the NVID(no vendor) AKU 2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exeYOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com.. Simply search for "Active Sync"
3. Install active sync, you might need to reboot
4. When your PC is ready run the NVID file you downloaded in step1 and follow the guide, remember that it can take some time and seem to stuck at 80% and higher, but just wait
5. When its done downgrading to the NVID WM5 rom, you prophet will reset and you can upgrade to the version of WM5 you want.
NOTICE
If you use a different AKU 2.2 ROM(like PDAViet Temp),you may have two EXEs in the folder you extracted.Be careful and use the one that is made for your device:
FILENAME G3.EXE
is for G3 devices:IPL x.xx.0000, SPL x.xx.000.0 (this is shown when you reset)
FILENAME G4.EXE
is for G4 devices:IPL x.xx.0001, SPL x.xx.000.1 (this is shown when you reset)
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
How to switch or upgrade/downgrade between WM6 versions(for example PDAViet->Trueneytral)
1. First you have to downgrade to WM5 AKU2.2 using the WM6->WM5 guide(some say that you don't have to do that,but i believe that it's better to downgrade first rather than making a simple overwrite)
2. Now follow STEP 5 of the WM5->WM6 guide
Device doesn't connect to PC after flash
If your device doesn't connect to your PC after flash,just enter bootloader(press camera button+while pressing soft reset and hold,until a tri-color screen shows up),and flash the NoVendor WM5 Rom: http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe .Then repeat the whole process...
----------------------------------------------------------
KEEP IN MIND:
UPGRADING CAN BE DANGEROUS,YOU ARE RESPONSIBLE FOR THE DAMAGE TO YOUR PHONE
DO NOT RESTORE BACKUPS FROM ANY ROM OTHER THAN THE ONE IT WAS CREATED ON
THERE IS NO "BEST WM6 ROM",THE BEST IS THE ONE THAT WORKS BEST FOR YOU
(part of the guide is taken from Da9L's guide,in the WM6 Rom Collection)
I will edit/update this post soon and clean it up, ask questions in another thread, and by god please read the wiki first, 90% of the questions asked are answered in the wiki....
WM6 Upgrade Guide...reply
great info sir! thanks so much! downloading...i'll be happy to send feedbacks on this WM6 ROM! thanks again!
Thanx a lot tonydeli7 , very very good guide and a lot of ppl really needed it
Great
Thanks to you all. I have Qtek S200 and trobuled with WM6 it wonderfull guide for me thank you very much.
I need to downgrade to WM5, 'couse I cannot boot anymore. After running the setup I get an error that the device cannot be found. I have connected the S200 with the boot loader running.
Edit: Now it works on an "old" WinXP machine.
Huge Problem!!
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
dharvey4651 said:
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
Click to expand...
Click to collapse
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
I followed the instructions carefully, and my phone (Qtek S200) seemed to boot with WM6.0
However, after aligning screen, it tried to initialize the phone with some extended roms, a procedure which failed, and I had to soft reset.
After reboot, it seems to work fine.
Is it?
EDIT: Another thing I noticed is that keyboard is in THAI !!! How can I make US the default? Olso, I have Resco keyboard GR edition. Will this work with WM6?
tonydeli7 said:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Click to expand...
Click to collapse
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
yoda_143 said:
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
Click to expand...
Click to collapse
i don't know mate.i believe you can use pdaviet's temp instead of aku2.2 nvid...
Another thing I noticed, is that it looses pairing with my bt handsfree...
I am making the pairing, and works fine. However, when at night I am shutting off my hf in order to save battery, the next morning the pairing is gone.
Any solution to this?
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
dufchan said:
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
Click to expand...
Click to collapse
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
I-mate Jamin
hello evrybody
i just wanted to know if i can upgrate my WM5 to WM6 on my I-mate JAMin?
rondol1 said:
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
Click to expand...
Click to collapse
thank u very much!!now my dopod working fine!!thanks a lot!!
thanx for the guide
help me please..
P4k1t0 said:
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
Click to expand...
Click to collapse
how to do that?
thx..
Choice of ROM
Hello guys, tanks for a so nice job !
I would like to have more information about the choice of ROM.
I don't want any special feature, just the row wm6.
no programs added, no tweaky today, no bugs, no battery problem, etc etc
which one would fit that the best ?
thanks
Thnx for this man, much appreciated!
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
joesa said:
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
Click to expand...
Click to collapse
Don't know for sure that it will help, but when you want to connect to your PC in USB mode (bootloader) you should first disable "Allow USB CONNECTION" in the conections settingpanel of Active Sync.
thanks i'll give it a try
joesa said:
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
Click to expand...
Click to collapse
Try to search the new ROM update utility and try to reflash using it.
pda is dead
hey friends..!!
i have a problem with my neo..
got new update of wm 6. 4..0.0.0.1 version..
phone gets switched off by itself.. sometimes..
when sms comes or i recieve a call..
i fear it has become a black brick..
plz help me out..!!
and..
one more thing..
is there any was to restore my contact.. i had a backup in wm 5..
the back up file when restored in w m 6..
contacts don t open.. then again i hjave to hard reset it..
lost my contacts and documents.. but i stii have that back up file..
plz help me out..
replies awaited..!!
dj00912 said:
hey friends..!!
i have a problem with my neo..
got new update of wm 6. 4..0.0.0.1 version..
phone gets switched off by itself.. sometimes..
when sms comes or i recieve a call..
i fear it has become a black brick..
plz help me out..!!
and..
one more thing..
is there any was to restore my contact.. i had a backup in wm 5..
the back up file when restored in w m 6..
contacts don t open.. then again i hjave to hard reset it..
lost my contacts and documents.. but i stii have that back up file..
plz help me out..
replies awaited..!!
Click to expand...
Click to collapse
For the WM6, try Gullum V6 Touch...
Now for the contacts problem - flash WM5 back, restore your contacts and back up them with PIM backup 2.5 (use search you will find it in the forum somewhere).After reflashing the WM6 you will be able to restore them again. The other option is to use Outlook to synchronize.
chavdar said:
For the WM6, try Gullum V6 Touch...
Now for the contacts problem - flash WM5 back, restore your contacts and back up them with PIM backup 2.5 (use search you will find it in the forum somewhere).After reflashing the WM6 you will be able to restore them again. The other option is to use Outlook to synchronize.
Click to expand...
Click to collapse
It's beter NOT to use any backup software when you migrate from WM5 to WM6 or the other way around. Sync first with your desktop ans sync back after upgrading. The standard location are not the same, so it is messy when you replace the files to their original positions.
Hi all,
I have tried the bootloader recovery but when I try and install the NVID rom while on the bootloader screen, it says error (260) the update utility cannot connect to your pda/phone. However on my vista machine the device manager recognises a HTC 'pocket pc usbsync device' while my prophet is connected on bootloader.
I did upgrade from PT VII to Crystal 2 (no error messages) without downgrading to WM5 NVID first. I only did this because I had an error that seemed to not let me downgrade to the NVID rom, so then I got lazy. My bootloader still comes on and if I reset normally it just gets stuck on Qtek screen showing OS 6.0.0.1 - is there still hope?
Just if anyone has a suggestion + thanks for the great work on these wm6 roms.
shreddo said:
Hi all,
I have tried the bootloader recovery but when I try and install the NVID rom while on the bootloader screen, it says error (260) the update utility cannot connect to your pda/phone. However on my vista machine the device manager recognises a HTC 'pocket pc usbsync device' while my prophet is connected on bootloader.
I did upgrade from PT VII to Crystal 2 (no error messages) without downgrading to WM5 NVID first. I only did this because I had an error that seemed to not let me downgrade to the NVID rom, so then I got lazy. My bootloader still comes on and if I reset normally it just gets stuck on Qtek screen showing OS 6.0.0.1 - is there still hope?
Just if anyone has a suggestion + thanks for the great work on these wm6 roms.
Click to expand...
Click to collapse
you have to go to bootloader mode .. press camera button and hold it then reset your phone , then keep holding the camera until you get to bootloader. then connect your ppc to you pc. don't care about activsync. just run the wm5 downgrade. you should be able to upgrade after you downgrade to wm5.
Success! - it appears that it was my PC running Windows Vista which is not initially compatible with running the RUU rom update files whilst in bootloader.
http://www.modaco.com/RUU-Vista-done-u-t252977.html
I have a problem:
I flashed my hd2 from a stocked rom 1.42 dutch version, with hspl 1.42. I installed a custom rom from: HTC HD2 Laurentius WWE 21891UltimatePOWER.
it worked fine for 2 or 3 days and then it stocked, i reseted the phone and
When i turn on my HD2, i get a white screen. and it doest go away. Even after softreset (volume button down in bootloader)
When i go in to bootloader i see this screen:
Pb81100 hx-bc
Spl-1.42.hspl xe
0x05
Cotullahspl 0x30
Click to expand...
Click to collapse
When i try to instal a rom by going in to bootloader en then start in win xp the update wont start, it stocked at 0 %
Then i tried to flash a orginal romt by sd:
it stocked at 7 % and i get this screen:
_______________________RUUNBH
PB81100___HX-BC
SPL-1.42.__hspl___XD
________________0x05
CotullaHSPL______0x30
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
- Then i tried to flash a radio rom by activesync, in xp it wont start,
- i tried flashing by sd and it stocked on 98%
- I tried different to install a rom and radio rom by vista, but also no succes
- I tried task 29 (by the Attached Task29 into a single exe.) to erease all data from the phone, but in windows by activesync it wont start
i tried al the above from windows 7.
Is there anyone that can help me, please i getting very desperate.
VERY VERY IMPORTANT! Try and read 2-3 times what is written here http://forum.xda-developers.com/showthread.php?t=609477
Only afterwards proceed to the following :
First of all....try and use Windows Vista or Windows 7.
Second of all....do not try to use task 29 because its a bit more complicated and it involves some drivers and so on!
Use this little thing here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 and after its completed....flash a proper radio something like 2.08.50.xx which you can find on Radio dedicated section here http://forum.xda-developers.com/showthread.php?t=611787
After all these....flash a custom ROM but be careful to be one suited with your radio! Which is a radio appliable for most of custom ROMS BUT be VERY careful!
Another thing.....do not flash from SD Card....Use the CustomRUU tool and flash it via ActiveSync!
Do you get any particular error message? When in bootloader mode, does "usb" show at the bttom of the screen? If so, try moving to a different usb port, preferably at the rear of the pc, or try different cable or even different pc. If still no luck, try uninstalling and then re-installing the latest version of Activesync.
The White Screen issue sounds like the incorrect radio version for the rom. I'm not familar with the details of the particular rom, but there are certain rom/radio combinations that will do that if they do not match eg running a 2.10 based rom with a x.xx.51.xx radio. The phone works intially until a reset and then hangs.
viperd said:
VERY VERY IMPORTANT! Try and read 2-3 times what is written here ......
Click to expand...
Click to collapse
Thanks for the replay
I tried, flashing by activesync. i flashed it the first time by hspl (the tread you link to) and then by activesync. But like i said, the hd2 stops at a white screen, so i tried by every possible way i could think of. Also i tried task 39 by the tool you mention, but it still does not work.
But i will correct my ts.
@clydeb1
I tryd to flash different radioroms, but if it try by activesync it wont start and by sd-flash it stocks at 98%, but i will try a different active sync
Okay,
I tried the following options:
- I installed a newest activesync and tried to instal an new rom under windows xp. The update stocked at 0% and i tried to install radio rom, with the same results
- I installed the windows mobile on windows 7, and tried the same as in windows xp, and still the same results.
Then i tried flashing every rom from the site by the sd-method (after every bad flash i formatted the sd-card with fat32)
With the sd method the phone stocked at 99% and then gives the next images:
00018003
LEOIMG.nbh - Fail
Radio_V2Fail
Update terminate
update fail
Click to expand...
Click to collapse
IS there any one how has a solution for this problem
Ok....try from the beginning!
1.Get from here http://forum.xda-developers.com/showthread.php?t=611433 HSPL2_RUN.zip (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....http://forum.xda-developers.com/show...3&postcount=19
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
viperd said:
Ok....try from the beginning!
1.Get from here (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
Click to expand...
Click to collapse
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Give the phone to someone who can get it to work??
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
korenbloem said:
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Click to expand...
Click to collapse
Thanks mate, if my suggestion doesn't work hopefully you can help him.
xmoo said:
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Click to expand...
Click to collapse
@Korenbloem,
A simple hardreset would have fixed your issue as well.
Instead of all kind of panic experiments like mtty/ flashing radios/roms from sd you could have come to me and I would have helped you.
You flashed a very old rom from the rom archive but never the less that rom is intensivily tested by me and the beta team.
I have no idea what kind of software you installed/tweaks you did or anything else but also with installing the wrong software it could cause the rom not to boot anymore.
Sorry to tell you but these 'bricking' stories are mostly caused by unexperiened users and it
making me sad to see more people are opening threads like this blaming a rom and causing a panic reaction in public destroying our work.
I realy hope you fix your device and I will try to help you but this isn't a rom issue.
Leo
Laurentius26 said:
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
Click to expand...
Click to collapse
Thanks for the adivse, but i already tried that with an orginal rom, but i will try it again, mabey there is a difference with a shipped rom.
The first thing i did was a hard reset, but that did't worked. (the phone is in this shape for 1 month now).
Second. I am not blaming you or anyone. I flashed the wrong radio rom i think (cant remember witch one) And that is my own fault. I never wanna make the suggestion that it is because of youre rom.
I took a risk by flashing my phone. and i is my responsibility.
Edit: I tried a shipping rom nld. But it gives the same error as always, only after 7%. But thanks for the advise
@ Xmoo, First of al thank you that you want to help with a sollution. But what does that mean a goldcard and what are the consequences of using it.
Laurentius26 helped me with fixing my device.
The problem was the radio. and by flashing a factory rom from t-mobile, the hspl was reset to spl 2.00. After that he flashed a orginal shipped rom (the orignal one from my device). And the rom is fixed again SPL 1.66 is now on the device.
Laurentius thanks for al the help!!!!!
HD2 bricked?
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
vanbasten88 said:
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
Click to expand...
Click to collapse
Do you have a branded Leo? If so, enter bootloader (remove battery, press volume down, insert battery), connect via usb (maybe you have to wait for driver installation), start the latest *.exe from your operator/carrier...
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
andreftx said:
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
Click to expand...
Click to collapse
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
silverwind said:
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
Click to expand...
Click to collapse
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
andreftx said:
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
Click to expand...
Click to collapse
The 1.66 ROM you posted above has radio version 2.06.51.07 with it. So have you considered trying to flash that radio version and then flash the ROM. I know if you get the ROM to flash it will flash that radio anyway. But you seem to think you flashed a wrong radio so just thinking out loud here.
unable to flash 3.27 rom on my htc hd2 ........its a t mobile product but unlocked as i use it in india so i tried to flash asia version but it start and completes only 8% thn nothing happens and gives error [262]:which says
UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode
Its goes to the tri color screen where it says upgrade ROM code error Please try again.
Plz help
in download mode it says:
PB81110 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
your device is CID locked which stops none t-mobile roms flashing.
First thing you MUST DO is check what version HD2 you have:
if it has green & red, call/end keys it is the t-mobile USA version (TMOUS) & flashing the wrong radio on that model will result in a bricked device.
if you have standard model with white icons on keys then you will need install HSPL prior to flashing the ROM update, HSPL will bypass CID fixing 262 error ...
HSPL & ROM links for all models including ROM direct download links for TMOUS HD2 can be found in HD2 wiki.
Go look & read it all & be sure you know what you doing before proceeding to flash ...
can u tell me how to unlock cid and can this screen tell me about the rom whether it is 512 or 1024.....
I see you have HSPL already.
are you flashing from computer or trying sd card flash ?
I would also assume it is 512 EU version from details above
try the latest HTC Generic WWE ROM from Wiki section & perhaps try HSPL4 to reflash HSPL as maybe corrupted nand issue. Also do flash from PC via USB cable & make sure PC has activesync or WMDC installed (all can be found in HD2 Wiki)
i m flashing it from my pc as my phone doesnt start when i switch on it stuck on screen saying SOFTWARE UPDATE FAILED PLZ TRY AGAIN......
i tried to flash HSPL4 but it gave me error http://prntscr.com/1stcv1 ......
n also i have WMDC but i doesnt show up my phone but in tri color screen mode it shows usb....
yes it hav 512 rom
Sounds like corrupted nand & model id is perhaps corrupted too.
Try resetting via reset button.
Have a look at these thread:
http://forum.xda-developers.com/showthread.php?t=1001452
http://forum.xda-developers.com/showthread.php?t=1182215&page=2
thanx a lot......just performed task29 and got htc white screen and now can u tell me which rom to flash n can i make it converted to android:good::good::good::good:
First get it fully working on a WM6.5 ROM & test it for 2 or 3 days, then if good look at the Android nand section & look for a Android build you like & has good feedback & current support.
Post 4 above has a link to an HD2 HTC generic WM6.5 ROM but you can choose something else if needed by looking at the ROM links in the HD2 Wiki
xdriver said:
thanx a lot......just performed task29 and got htc white screen and now can u tell me which rom to flash n can i make it converted to android:good::good::good::good:
Click to expand...
Click to collapse
Hello xdriver,
if you want Android on yor phone you mighr opt for installing via NativeSD method, giving you the advantage of trying out different builds and choosing the one that suits your needs at best. Also, if somwthing goes wrong you always have WM fully functional on NAND. But consider buying a decent SD card first, meaning one with exceptional good random r/w access speed. You'll find tutorials in the SD section.
Have fun!
Best regards
Getrid…
Sent from my HTC HD2 using xda app-developers app
thnx 4 the info frnds but after doing task29 thn also it stuck at 8% and give same error stated in post #1 and now my phone doesnt start up when i switch it on it vibrates for 3-4 secs n nothing happen after i tried to flash wwe asia india ROM ............... maybe it is battery problem now i charging it to check the prob...........
its getting into the bootloader mode now i m download a lower version of ROM .......Hope it works