i've installed diamond black 3.1 rom and tonight i changed registry with advanced config tool(its in this rom-i have changed system cache)....after soft reset device freeze at boot screen. hard reset doesn't work..."format failed"-this message only appers.i have entered bootloader and installed wizard love rom...didn't help. i think that registry messed up everything...how can i get back to old registry when i cannot make a hard reset?? my device is SPV M3000 G4 its CID unlocked.It's strange cause device is charging battery and i can enter the bootloader so i dont have a brick...but problems with hard reset and even wizard love rom couldnt help....can someone had this problem too??
looking for ur advice
thanks
when you say you installed wizard love did it go through install all ok but still no boot?
yeah it went all good...i have instakked it without a problem 100% finished and as usual soft reset...but still freeze at boot screen...it drives me mad, i have tried almost everything and i dont know whats happening
stilll not workin'
i have tried everything...have installed 2 difrent wizard love roms and my htc wizard still freeze at boot screen...i can enter the bootloader and install roms but they are all stuck at bootscreen...my problem started when i changed system cache in my registry using advanced tool configuration ( BD 3.1). first after soft reset Wizard was frozen at windows screen, after hard reset it was hanging at touch screen config...i tried to hard reset again but i can only see info that "format failed"....what can i do now?? pleeeeaseeee help....
does your operator have a stock rom you can download?
i was looking for it...i need polish Orange ROM SPL 2.22.1.1 maybe..its my 2nd night fighting with that freezy bastard...do u know where to find one??i have seen some SPL's but they are for NL orange...do u thnk that original rom from orange will help??
kayzerrr said:
i was looking for it...i need polish Orange ROM SPL 2.22.1.1 maybe..its my 2nd night fighting with that freezy bastard...do u know where to find one??i have seen some SPL's but they are for NL orange...do u thnk that original rom from orange will help??
Click to expand...
Click to collapse
Polish SPL= the same as Dutch SPL.
Orange SPL = t-mobile SPL etc..
Only the version changes..
Operators cannot edit the SPL's, they have to use HTC's SPL's.
What only differs is the CID block, which will not be overwritten when flashing either IPL or SPL.
sooo...i tried to remove the HARDspl but i couldnt get into my wm cause device freeze at bootscreen so i have downloaded the spl nk.nbf for orange and flashed this file with RUU...i have now 2.18.0001 SPL but Dutch rom cannot be installed it shows some error INVALID ID or something like that...I dont think that polish and dutch roms are the same because i cannot flash this dutch rom...have u got any idea what i should do next?? its really annoying cause ive tried almost everything and still no progress....and i still dont know if i removed hardSPL with this method that i described...in order to flash an original rom do i have to go back to CID lock??
i tried to install NL Orange rom but its not working...i can only get message " INVALID VENDER ID" with other roms like T-MOBILE i get message "UPDATE ONLY" --try to get newer nk.nbf file...what should i do now??
Related
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
nstefanelli said:
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
Click to expand...
Click to collapse
Check your PM's
bwesty said:
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
Click to expand...
Click to collapse
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
jUST DO WHAT I SAY
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
samy.3660 said:
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
Click to expand...
Click to collapse
I cannot do that because the Carrier ROMs that I have aren't for G4, so they arent working. I have three different carrier ROMs for my phone.. and none of them work.
-Stefanelli-
nstefanelli said:
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
Click to expand...
Click to collapse
Check your email, I downloaded and zip works fine here.
i'm facing this problem right now , i will solve it with the original rom .
the problem started when i used shelltool to upgrade my G4 CID Locked to windows mobile 6 crossbow underground edition .
i will give it another try when i get my device alive again ,
any suggestions for the WM6 underground to make it work using shelltool on my wiza 200 ??
--------------------- Edit -----------------------
Finally i solved the problem and installed Crossbow WM6 underground edition .
all i did is to install the original rom from provider and then used shelltool to install WM6 .
i want to mention that my wiza200 is G4 and its CID Locked .
Huge thanx to mUn , you are da man
Mmm
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
lobiik said:
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
Click to expand...
Click to collapse
whats your device and is it G3 or G4 ?
try to do as i did and it worked for me , install the provider flash , then try shelltool to flash WM6 underground .
WBR
a-h-t1 said:
whats your device and is it G3 or G4 ?
Click to expand...
Click to collapse
Mine is G4, dunno if cid is locked or not. I've flashed it as I said with wizard love rom and working without problems. I've tried that again this morning, to flash from love rom, but the same. At 96% it hangs, error 302 Communication error, then starts recovery process, phone goes to bootloader mode. Then is possible to flash it with love rom again with no problem
g4
i have a g4 wizard using the shell tool i have chaged my rom on my phone sometimes 3 times a week just to test them out
the shell tool works if you cant download from the forum here is the link for it
http://rapidshare.com/files/17787647/ShellTool_bugfixed.zip
G4
yes, but when I run shelltool, and press get rom info, all fields states N/A
info from phone is:
ROM Version: 2.26.10.2 WWE
Radio: 2.25.11
ExtROM: 2.26.10.105
IPL/SPL: 2.17.0001
And anyway, dunno exactly which rom for WM6 I can put in (I've just 5.underground_edition_Crossbow_ROM.exe which stucks at 96% with 302 error)
well, I'm dumb, mislooked one stupid thing. Everything passed without errors, Windows Mobile 6 is up and running
happy to know that , the problem was installing rapi ha ??
WBR
No, not really, rapi and that second cab was in device, it was restarted, but I did a mistake - i didn't copied that desired rom into updater directory - that was why were all fields N/A... did that, flashed on first try, without problem
I had the same problem, orginal rom from the provider, and I can reflash it again.....
THX for the info......
ROM verion and link location
Hi lobiik,
which ROM did you use for your device, as you comments above:
"i didn't copied that desired rom into updater directory "
can you please point me to location where i can get the ROM, also proper steps to install the same.
Thanks,
Ajay
HELP!!!!!!!!
I tried flash my G3 with shelltools the program said it worked well i did hard reset then i turned it on it is stuck on 1st front screen bootloader mode is stuck i dont know what is is my device bricked
---------------------edit--------------------------
im a newbie
Hi All,
I tried flash by wizard following http://forum.xda-developers.com/showthread.php?t=298967
Every thing went well but I was not able to HARD RESET. So instead I removed the battery and started it again. It starts up but got struck at screen which says
IPL 2.21.0001
SPL 2.21.0001
GSM 02.19.11
OS 2.18.00
Could some help me what to do now. I read some threads to go to Boot loader screen by pressing "Camera" + "Reset" button and got USB at bottom left and tried RUU with some thing available on forum but every thing failed saying "connection not established"
Please guide me to solve this problem.
if ur device is CID LOCKED "G4" u need to flash the official rom 1st then flash with any G4 safe rom available >>
USING :
ShellTool
http://forum.xda-developers.com/showthread.php?t=293480
or
SoftSPL
http://forum.xda-developers.com/showthread.php?t=329147
Thats the only way for G4 "CID LOCKED"
No...
If OS is not boot up correctly, both ways doesn't work because all of them requires to do in a working OS.
You should find your stock ROM or Wizard Love ROM, use the bundled RUU to flash it so you get the device working again, then use SoftSPL/flash HardSPL and use RUU to flash OS-only WM6 ROMs.
Yes starkwong you are right. I bought my device back working by flashing it with "wizard love" now its up and running. I would proceed with Soft SPL/Hard SPL and then try to flash it with WM6.
hey, im new but have read many of the pages here. i have burnt roms to my first wiz (G3) unlocked it and everything went well. i came about a wiz (G4) last week wm5 bland rom locked and want to get wm6 on it so after my research i went to the IMEI unlock site and purchased the unlock for the g4
the unlock seemed to go well the first time but, it won't come out of boot loader mode
i ran hornet o.10 for g4 it runs and completed to 100 % and then on reboot it comes up with the boot screen again
IPL 2.21.0001
SPL 2.21
i ran the tnt 1933 rom this morning and it completed 100% but still i have a boot screen
i know im missing something the battery power is fine .
i downloaded the stock rom for cingular but it won't load it has error "(294) INVALID VENDOR"
any suggestions ...
thanks in advance for your input
Airborne_Pathogen said:
hey, im new but have read many of the pages here. i have burnt roms to my first wiz (G3) unlocked it and everything went well. i came about a wiz (G4) last week wm5 bland rom locked and want to get wm6 on it so after my research i went to the IMEI unlock site and purchased the unlock for the g4
the unlock seemed to go well the first time but, it won't come out of boot loader mode
i ran hornet o.10 for g4 it runs and completed to 100 % and then on reboot it comes up with the boot screen again
IPL 2.21.0001
SPL 2.21
i ran the tnt 1933 rom this morning and it completed 100% but still i have a boot screen
i know im missing something the battery power is fine .
i downloaded the stock rom for cingular but it won't load it has error "wrong update utility"
any suggestions ...
thanks in advance for your input
Click to expand...
Click to collapse
Are you sure SPL is 2.21 and not 2.21.0001 as IPL 2.21.0001 ?
Well,if its 2.21 only,the phone's got mixed Bootloaders (IPL/SPL),IPL 2.21.0001 are G4 and SPL 2.21 is G3,I don't know how you got it,but your phone is 'Bricked'
mmm it figures
so it appears there could be a problem with the imei program,
as i said it never came out of boot mode after the unlock
and no errors were shown ...
i could get another and replaced the main board, this one is in new condition
except for the custom bricked rom . in the future i will not play with a g4
thanks for the diagnosis, no way to flash a new spl / ipl ... i did read that if
it booted you could get it back in some chance cases .. i am curious as to how this happened (others not doing this for a hobby could brick there only phone)
step 1 - ran imei unlock
never came out of boot mode after
2- flashing the to above roms said to be G4 safe
i never look to see what the ipl / spl were before
i looked with the wizard tool but didn't save it
well you live and learn, it's good for parts now off to ebay for another crack at it ...
thanks everyone ... the best thing about this phone is everything you can do to it
with help from those who know ...
I recommend trying to flash back to original service provider ROM, then unlock again and try another. As long as you can get to bootloader (tri-color screen), there's still hope for your phone. When it's in this mode, and you plug in the USB, does it say USB at the bottom of the phone screen? If so, you are not dead yet.
Custom build wm6 roms like TNT etc... never Brick a G4 phone as no IPL/SPL is included in them,they are completely safe for G4 devices.What I can gather,it must be the wrong imei unlock code perhaps.
Well,like Myrddin Wyllt said,there's no harm in trying,so if it gets into Bootloaders,try to flash the official rom and if there's an error "wrong update utility" ,replace the RUU in the rom with this RUU and run this RUU,hope it might work.
Myrddin Wyllt said:
I recommend trying to flash back to original service provider ROM, then unlock again and try another. As long as you can get to bootloader (tri-color screen), there's still hope for your phone. When it's in this mode, and you plug in the USB, does it say USB at the bottom of the phone screen? If so, you are not dead yet.
Click to expand...
Click to collapse
yes sir i can talk to the phone from xp pro ..
USB does come up
so i can swap the RRU with the nbf file i need ...
no file name change required on the xxx.nbf file
thanks alot for the(schooling) advise ... i was going to need to brick another to make some book ends... this could save me that
stuck
Airborne_Pathogen said:
yes sir i can talk to the phone from xp pro ..
USB does come up
so i can swap the RRU with the nbf file i need ...
no file name change required on the xxx.nbf file
thanks alot for the(schooling) advise ... i was going to need to brick another to make some book ends... this could save me that
Click to expand...
Click to collapse
ok, i swapped out every RUU i could find i get errors from
read file
invalid vendor id
wrong update utility
im too new to figure this out ..can you extract a ipl / spl from an
official rom and then flash that to get the boot loader's back in sync
i found the att 8125 ipl /spl nbf when i flash, it runs to 100% reboots but no changes
anyone have a link to flashing just the ipl / spl on the g4
i am most thankful for any advise ..
try running the hardspl on phone, it might just work to revert it back to a G4 spl.
Link to HardSPL : http://forum.xda-developers.com/showthread.php?t=332320
and G4 ipl and spl here : http://forum.xda-developers.com/showthread.php?t=342744
Also I paid to the IMEI Check and I had to change the plate because the PDA died as yours. E had not returned to the money of the IMEI Check only reply to me was that it had to change of plate ..... It had the unblocked CID?
bastards
yes they won't return my money ... somehow they bricked my phone
i would use the hard /spl and not the imei those guys are assholes
Hi,
i flashed a rom 2 weeks ago, everything went well. yesterday i wanted to flash another os but before i could flash it, it seemed to get bricked. It stucks on the "HTC Splash" (not the WM6 Splash). I read a lot of threads and wiki threads but i don't unterstand anything! What i've to do to unbrick my phone? I tried to flash another rom but after 0% of flashing a error appears.... flashing with sd card doesn't work, too it changes to bootloader after the "Loading..." screen
i havent got hardspl or something...
please help!
UPDATE: i got the sd flashing to work... same thing but: now it stucks at the WM splash, not the t-mobile/htc one...
You need to find out what SPL you have (I'm guessing 2.03 but if you have 2.10 olipro then its got Hard SPl on it) and then do a search for "bricked SPL x.xx". You will probably find a HEAP of posts. However, some advice that seems to recover a small minority (sometimes with the "No GSM" error) -
1st thing to do is do a hard reset. Both softkeys and reset with stylus. Hold in all buttons until it asks if you want to reset to factory. Press "R" on the slideout keyboard and the "Space".
Hopefully this will fix. If it doesn't, Put it in bootloader, connect to pc (make sure "Allow USB Connection" Active Sync settings have been unticked) and run the SHIPPED STOCK ROM. This is the rom the Hermes came with originally. This MAY fix it otherwise you're in for some major reading and hair pulling.
If you should fix this then PLEASE, for the love of god, Hard SPL your Hermes before going into the wide world of flashing.....
Good Luck...
thanks i'll try it. hard reset causes kinda... nothing^^
i hope i can fix it otherwise i'll buy a touch pro
...but i think it doesn't work, because i flashed a shipped rom via sd card yesterday and the problem is still there... isn't there any way to put hard spl on my device, yet?
Try re-installing the stock rom again using sd card (if thatys how you did it last time), it could've been a bad flash. I've had those a couple of times myself. Just remember to install Hard SPL if you're successful as it makes it SOOOO much easier to recover from bad flashes.
Last thing to check would be if you have "bad blocks" using MTTY. If the boot sector has been stuffed up this may cause this problem. Do a search through the wiki, its been covered extensively...
Cheers...
okay i think my problem is solved: t-mobile replaced my device
first thing i'll do with my new device: HardSPL^^
anyhow thanks!
Upgrade successful but now stuck
I have a Three (au) Dopod 838 pro, which I upgraded from the original Windows Mobile 5 to the Three Windows Mobile 6.0 ROM. Unfortunately I didn't read up on this site first, I thought it would be straightforward since it was a ROM from the manufacturer and all, so I haven't Hard SSPL.
The upgrade reported as successful and my PC disconnected but the phone won't boot, it sticks at the Dopod screen with some numbers at the bottom. They are:
M 05 R 1.47.30.10
S 04 G 32.80.7020.20H
B 07 D 3.54
I have tried hard resetting, and returning the phone to bootloader and reflashing the same new ROM image, always with the same result.
On the bootloader, it says
HERM100
IPL-1.04
HERM100
SPL-2.03
Is there anything which can be done or is it a trip to the service centre (wherever that is)?
Just checking - Hard reset = both soft keys above the dialler closest to the lcd and reset with stylus. Hold in until it asks if you want to reset to factory. Press r on slideout keyboard then space.
This is a hard reset, not just using the stylus.
Otherwise, you have a LOT of reading material to go through with (maybe) no actual solution.
Cheers...
tried that
Thanks, but yes, I had tried that, a number of times. I think the phone will be going to a service centre today.
I want to help someone on this please , bcs HTC SPV M3100 when i'm trying to switch on phone was stuck on HTC logo and nothing more , i have try to put on boatloader mode and phone was going on bootloader mode three color screen and show this:
HERM100
IPL-1.04
HERM100
SPL-2.03
i'm trying with hard spl from Pof soft but error getting.
Can someone find a time to help me?
hallooo
experts please!
Hello haveri,
what ROM are you trying to start? I was stuck on HTC logo too, when I tried to start a ROM without installing Striped ROM first, which was highly needed. So I done hard reset(three color screen), and flashed again.
For starters, put in bootloader, connect to PC (1st untick "Allow USB Connections" in activesync) and run Hard SPL V7. Install it on your Herms and hope it works because otherwise you are in for a whole heap of hairpulling frustration...
If you get Hard SPL onto your Hermes then use the sd card method to flash a new rom...
You could have avoided this by doing a little research instead of going full pelt into flashing, you Hard SPL BEFORE you get into trouble, NOT AFTER....
Hi guys,
I have a similar problem with a T-Mobile branded TyTn from a friend of mine who thought flashing ROMs without putting device into HardSPL would be clever.
The devices has also IPL-1.04 and SPL-2.03 and from the bootscreen it looks like WM5 should have been installed. I also get the "NO GSM" message and I REALLY tried every fking method but without success.
I even created a Goldcard (and verified on another device it's working, level 0 instead FF) and tried to flash several ROMs (also Cingular WM5 ROM and original german T-Mobile ROM) but no luck.
I also tried to run HardSPL V7 but as far as I remember it just said it cannot connect.
Funny thing: HardSPL V9 DOES start flashing and on the PDA and the PC the bar shows 100% but some moments later it says "Could not update" (or something like that).
I even tried different mtty methods from several posts from the forum (erasing the NAND on different ways, qtek loader method with erasing the first blocks) but I'm really really frustrated now and I believe there is no solution here?! (device has no guarentee)
So, if someone has ANY hint or useful information write it down or send me a PM.
I gladly appreciate your help and hope for a solution!
Cheers
P.S.: I couldn't find any information saying Goldcard method works (or even exists) for Hermes. Can someone confirm it does really work?