Radio Upgrade Help - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Hi I know its been asked for number of times but I can't find the correct answer for this.
I wish to upgrade my radio version to ATT latest radio (HERM_Radinly_1.54.07.00). I have it downloaded from wiki and trying to follow the instruction.
1. Extracted HERM_Radinly_1.54.07.00_CustomRUU.rar.
2. Disabled Active Sync.
3. Entered in Bootloader. Phone connected to machine. Its in USB mode now.
4. Now when I run RUUWrapper.exe, I get a screen where I have to make some selection. And here I need some help. There are following options,
a.SPL 1.01 MFG Bootloader
b.SPL 1.04/1.10 SPL 1.09 Bootloader
c.SPL 1.11/1.13/1/30/1.35/1.40 Bootloader
d.SPL 2.02/2.10 New Bootloader
b. Force Using SSPL
Check Box for Is HardSPL?
Now if some one can help me to find out correct option in the list, I can move further. My current SPL and IPL are in my signature. As far as I remember I have HardSPL done too.
Any help will be really appreciated.
Thanks -nbhor

nbhor said:
Hi I know its been asked for number of times but I can't find the correct answer for this.
I wish to upgrade my radio version to ATT latest radio (HERM_Radinly_1.54.07.00). I have it downloaded from wiki and trying to follow the instruction.
1. Extracted HERM_Radinly_1.54.07.00_CustomRUU.rar.
2. Disabled Active Sync.
3. Entered in Bootloader. Phone connected to machine. Its in USB mode now.
4. Now when I run RUUWrapper.exe, I get a screen where I have to make some selection. And here I need some help. There are following options,
a.SPL 1.01 MFG Bootloader
b.SPL 1.04/1.10 SPL 1.09 Bootloader
c.SPL 1.11/1.13/1/30/1.35/1.40 Bootloader
d.SPL 2.02/2.10 New Bootloader
b. Force Using SSPL
Check Box for Is HardSPL?
Now if some one can help me to find out correct option in the list, I can move further. My current SPL and IPL are in my signature. As far as I remember I have HardSPL done too.
Any help will be really appreciated.
Thanks -nbhor
Click to expand...
Click to collapse
You are right, this has been asked a number of time... . May i suggest another method to load your rom?: SD card. You do not need to use a USB connection (no risk to loose it) nor a PC and it works perfectly.
1> format a sdcard in FAT32 (use a card of max 2GB)
2> copy the .nbh file to it (Preferably the only file on the card)
3> rename the file: HERMIMG.NBH
4> insert the card and push: OK-POWER-SOFT RESET (to go to the 3 colors screen). It will detect your hermimg file (says "loading" in blue) and describe the content
5> follow instructions on screen.
And that's it ! Just note that flashing a radio rom is slow. This means that you will have the impression that it stops time to time. Just be patient
Oh... by the way, having tried nearly all radios available, 1.47 is for me the best compromize between battery drain and performances (at least in my area). But, once again, this is a matter of taste. Make your religion

Thanks a lot. Actually I have followed the same process while upgrading from WM5 to vp 3G's WM6. But I was not aware that I can use same process to upgrade the radio only. And to my surprise it worked like a charm. Appreciate your help in this matter. I will update you with my experience on this radio version.
Thanks -nbhor

Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?

terminatermule said:
Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?
Click to expand...
Click to collapse
As far as you can still flash, the method explained above should work

terminatermule said:
Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?
Click to expand...
Click to collapse
Hi Glenn this happened with me for couple of times too. Didn't ask anything in boot loader.Then I went back to board and did as this thread says http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing and this helped. May be this will help you too. All the best.
Thanks -nbhor

Hi nbhor,
Thanks for that, I had read that thread but not stressed much about preparing the cards, a format and error check (which ti my amazment found bad sectors on two brand new transflash cards sorted it and it now tries to flash but still fails unfortunately. Oh well looks like no radio for me again :-(
Cheers Glenn

Related

HTC HERMES (M3100) - fatal crash, PLEASE HELP!

Hi,
I recently had a power cut (yes, a lights off power cut!) that killed my PC half wat through installing the Cingular English CWS__001 1.34.502.1 09/21/06 ?? 1.16.00.00 32.53.7018.01H 14955.2.3.0 ROM onto my SPV 3100.
Now SPV 3100 will boot to the ROM I was running prior to the upgrade but I can't use the telephone. I'm also not able to rerun the upgrade as it got far enough through the process to upgrade my bootloader to 1.06 - therefor rendering me unable to load another ROM.
Before the crash I was using the Imate ROM as below and M3100 was sim unlocked and running on o2 3G
i-mate English CDL__001 1.20.305.3 07/21/06 1.20.305.104 1.07.03.10 32.41.7010.02H 14955.2.3.0 1.04
Please help.
Thanks
If your device is still working ok as a PDA then hopefully it just screwed up the radio update of your device.
Try reflashing the Radio only
Look Here
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Post back with results
Regards
S.K
EDIT: Sorry only works on 1.04 bootloader only. Afraid your gonna have to wait for Pof to come up with a 1.06-1.04 workaround
Hi S.K,
Thanks for the info. I have now tried installing the HERM_1.20.31.10_type2_radio_fixed upgrade but unfortunately the radio upgarde crashes also. It all seams to go well, (after using MaUpgradeUt_noID.exe twice) the phone says "Upgrade Radio Stack Please wait" and the progress bar appears on the PC but then after 10 mins I get an ERROR 114: RADIO ROM UPDATE ERROR.
Do you think this might be becuase the last upgarde partly installed bootloader 1.06?
Any other suggestions - I'm desperate to get the hpone on M3100 working again.
Thanks
Read here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Please post USB monitor capture, otherwise can't help u.
Hi Pof,
Thanks for the offer, I will sort out the usb software on Monday. Are there specific actions that I should try, obvioosly I will usb monior everthing I do but I want to keep it to the point and not waist yr time trailing through huge log files.
Cheers
BTW - I have tried all options of recovery, such as attempting to install the latest radio and trying to install the new rom from an sd card, trying several roms and using imei unlocker - all without any joy.
I think the problem is that I have partially installed radio and bootloader 1.06 so I can't fix the problem.
Thanks again.
@wotthefok:
For me is faster to look at the usb log file, then I exactly know why the upgrade fails, otherwise I have to decode it from your feedback and I can't be really sure. Check the "upgrading problems" page on the wiki, if none of the steps there seems to fix your problem, post USB monitor log please.
Log Files as requested
Hi,
I have captured information using usb monitor and attached the zipped log files for your attention.
The first is called USB_monitor_log_Herm_120Radio_twice. This log details attempting to install the HERM_1.20.31.10_type2_radio_fixed upgrade, and running it twice - just in case.
The USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_twice.zip details attempting to install the RUU_HER_Cingular_1.34.502.1_1.16.00.00_wwe_cws_ship upgrade, simply using the standard ROMUpgradeUt.exe method. This generates the expected Vendor ID error.
My primary focus is to install the radio upgare or download my bootloader to 1.04. The PDA part of my m3100 does now freeze occasionally but at least functions whereas the phone is completely dead.
Thanks in advance.
Please attach capture in *ANSI TEXT FORMAT*, the .lgs file you zipped is totally unuseful
Edit -> Export and Save as type "ANSI Text files".
Also make sure you export in "COMPLETE" view, see the wiki for more details.
OK, Spot the novice.... I have now created a txt log file that captures activity of me running the 120 Radio upgarde - but only once this time. I still had to zip the file due to it's size. Hope this is OK.
I'll send the other logs within the next couple of hours. Please let me know if the output I have sent so far is acceptable?
Thanks
wotthefok said:
Please let me know if the output I have sent so far is acceptable?
Click to expand...
Click to collapse
No, it's a "basic" capture, you have to export a "complete" capture:
Start USBMonitor.
File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
In the upper part there are two tabs: basic and complete. Click on "Complete".
Right, Try again (duh!) OK, I've tried to keep the log files names as self-explanitory as possible... USB_monitor_log_Herm_120Radio_run1.zip is the r20 radio upgrade, 1st run and USB_monitor_log_Herm_120Radio_run2.zip the second run - without disconneting or resetting the device.
USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_ran_twice.zip is the Cingular upgrade run via the ROMUpgradeUt.exe, again run twice without disconneting the device.
Hope I got it right this time.....Please let me know if there is anything else I can do.
Thanks.
This time you got the captures right
- You're on bootloader 1.06: You don't have 'rtask' command, you won't be able to do any radio upgrade only.
- Your device is not CID unlocked (Security level=FF, unprivileged)
- The bad flash caused the CID area to corrupt (CID: Wait interpreter timeout)
- When flashing a full ROM you get a CID not allow (255) this is because your corrupted CID doesn't match the CID on the ROM.
The radio part is screwed, you could have fixed this if you where in bootloader 1.04 by flashing a full ROM, but as you are in 1.06 you can't because of CID checking. But you're lucky because the OS ROM is intact and you can boot the OS, you should be able to downgrade to bootloader 1.04 from OS and flash a full ROM after, which will hopefully fix your radio.
Just wait until a solution to downgrade bootloader is available (I'm working on it).
Hi,
As I suspected.... Suppose it's not all bad news though - just means that I have to be patient and use my communicator once more. Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
I have already got a IMEI-CHECK sim unlock from where I originally got the M3100 unlocked from Orange to work on o2. That said, I have run either unlocker 2 or 3 with the .unl that I know worked I now get
HTC HERMES v3c unlock
Starting communication.........
Checking device..............ERROR
The device you try to unlock is not supported.
Please contact your supplier site.
Device is rebooting
Press any key to quit this application.
I'm currently chatting to the guys at IMEI-CHECK re this problem.
Anything else I can do to assist you in anyway??
Cheers
wotthefok said:
Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
Click to expand...
Click to collapse
They have it (M3100v3cUnlock.exe), but it will not work on your device because your IMEI is corrupted and their unlocker will not be able to read it and to check/compare with the .unl key file.
Hi,
Just a quick update. The guys at MIGsofT LTD have VERY VERY generously said they'll have a look at the problem for me so my phone will be winging it's way to them today.
Thanks for your assistance and helping me be certain of the problem and to better understand the root cause.
Hope this information will prove useful to others.
Another quick update...
The guys at IMEI-CHECK (MIGsofT LTD) have rectified problems with my handset and managing to reinstall bootloader 1.04 in the process!!
They also turned my phone around in under three days and only charged me the cost of postage! I had previously been a customer of theirs but it was still a very generous and helpful offer and I would certainly pay for the service than have a duff handset - after all £250 + for a paperweight is rather excessive....
If you're experiencing a problem like mine why not get in touch with them and offer them money to have a look at your handset? No Guarantees but it seemed like my last chance, for a while anyway.
Praise to IMEI-CHECK for a brilliant service - they are King of the day !!

Wierd Issue

Ok I have searched the forums pretty hard the last couple of days, and I have not found anyone that has the same issue as mine. It's not too big of a deal as everything operates but it is an issue all the same. This is all of course after I have succesfully ran HARD SPL v7 and upgraded to Black 3.0.1. Basically I decided to use POF's SuperCid Unlocker 3a (yes I know if I had HARD SPL 7 then why go through the trouble of Unlocking my CID, let's call it a need to mess with things) and everything went succesful. Then after the fact I read that it is still good even if you have SuperCID to upgrade the SPL to 2.10 and have read some peoples signatures and it appears that they have succesfully done this. Here is my issue;
When I run the CustomRUU it autodetects my SPL no problems, HARD-SPL? is checked, everything seems to go fine until it gets to the boot loader, once it is there, the progress bar pops up, zings to 100% and then reboots, cool? no because it didn't actually upgrade anything everything is still the same. Ok, so I tried the format SD card and rename *.nbh file to HERMIMG.nbh and put only it on the card, when I go to bootloader it does a quick flash to the screen like it recognizes the image but then goes to boot loader and nothing changes (the flash is so quick I can't even read whatever message it may be showing). I have tried pretty much every flashing method I can come across. MTTY wont recognize that I even have a USB port so I have been unable to try that method. So two questions:
I have SuperCID, so should I continue to even bother to get to 2.10?
If so, is there anything else I can try? Or do I need to get MTTY to work and try that as that is really the only thing left?
Thanks for any and all help anyone can provide.
PuckX said:
Ok I have searched the forums pretty hard the last couple of days, and I have not found anyone that has the same issue as mine. It's not too big of a deal as everything operates but it is an issue all the same. This is all of course after I have succesfully ran HARD SPL v7 and upgraded to Black 3.0.1. Basically I decided to use POF's SuperCid Unlocker 3a (yes I know if I had HARD SPL 7 then why go through the trouble of Unlocking my CID, let's call it a need to mess with things) and everything went succesful. Then after the fact I read that it is still good even if you have SuperCID to upgrade the SPL to 2.10 and have read some peoples signatures and it appears that they have succesfully done this. Here is my issue;
When I run the CustomRUU it autodetects my SPL no problems, HARD-SPL? is checked, everything seems to go fine until it gets to the boot loader, once it is there, the progress bar pops up, zings to 100% and then reboots, cool? no because it didn't actually upgrade anything everything is still the same. Ok, so I tried the format SD card and rename *.nbh file to HERMIMG.nbh and put only it on the card, when I go to bootloader it does a quick flash to the screen like it recognizes the image but then goes to boot loader and nothing changes (the flash is so quick I can't even read whatever message it may be showing). I have tried pretty much every flashing method I can come across. MTTY wont recognize that I even have a USB port so I have been unable to try that method. So two questions:
I have SuperCID, so should I continue to even bother to get to 2.10?
If so, is there anything else I can try? Or do I need to get MTTY to work and try that as that is really the only thing left?
Thanks for any and all help anyone can provide.
Click to expand...
Click to collapse
Did you look on the bootloader screen to see if your SPL changed? To my knowledge the only place you can see it is in the bootloader screen (tri-color screen) And flashing Olipro's Hard SPL only takes a couple seconds so it sounds to me like it is working as designed.
Or are you trying to flash a different rom? If so then try deleting everything you have in the directory you are using and re-downloading. You might have over-written the file you want to flash with the HardSPL one. You shouldn't be using the hard spl wrapper to flash a rom in any case, i believe that is mentioned in bold at the top of the Hard SPL thread.
Ok nevermind I was able to get it to work and MTTY was the answer. This is the 2 steps I had to follow:
From the thread: http://forum.xda-developers.com/showthread.php?t=291723
sp3dev said:
Hi. I`ve finally found the way to connect mtty and run rom update utility in Vista. tested on rtm 6000.
First of all, connect your device when it`s in bootloader.
next, open Windows Mobile Device Center and in connection settings uncheck Allou USB Connections.
next, goto contol panel-administrative tools-services and start windows mobile device connectivity and windows mobile device 2003 connectivity
next, goto device manager and find your device and update the driver to the one from AS 4, i attached it, wceusbsh.inf.
then, kill wmdc.exe with any taskmanager
You are Ready. run ruu or connect MTTY. I guess that vista default driver uses another port, not WCEUSBSH001, that`s why we have to use the old driver.
Click to expand...
Click to collapse
Then Do This:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootloaderMFG
Flashing SPL-1.01 MFG instructions
Put hermes in bootloader mode (side ok + power button + softreset)
Connect Hermes to computer using USB cable.
Open mtty.exe, select "USB" from the dialog box, then hit Ok.
Hit enter twice and you'll see the "USB>" prompt.
Then type these commands: (note the use of 'lnb*s*')
USB>task 32
Level = 0
USB> lnbs SPL-1.01.nbs 50020000
USB> task 8
Device will reboot after this, with bootloader 1.01-MFG on it.
Once I was able to do all this I was succesfully at 1.01 at which point I ran the Custom RUU and upgrade to 2.10 without issue. Once again all right there in the forums, just had to be pieced together to find a solution.
Thank you all for all your dedication to these projects, you make owning a PDA more fun than I am sure was originally intended. I love messing with things.
I have also attached the necessary files from the original posts to perform this for anyone else facing this issue.
PuckX said:
Ok nevermind I was able to get it to work and MTTY was the answer.
Click to expand...
Click to collapse
Cool, glad you got it working

So Hopelessly Lost!

Even after reading this forum all nite, I am still soooo confused, maybe too much new info in m'head. At any rate, I am trying to UG from WM5 to WM6 and am having a heck of a rough time. Everything goes good until it actually starts the process, at which time I get the 260 Connection Error. After plenty of research on here, I decided to try to "flash" the ROM, to no avail, for nothing happened. I can get into bootloader mode but then nothing else happens (perhaps I'm not waiting long enough? How long should I wait?) and I never see the screen pictured here - http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing - so I just give up and reset. I am currently downloading the HardSPL utility so I can try flashing after the IPL and SPL ugrades. But I do have some questions still --
(1) Does my phone need to be "unlocked" to do this and how can I tell if it is or isn't?
(2) Can I just use the ROM that I downloaded from the HTC site or must I use one found somewhere on this forum?
Any other advice? All will be appreciated. Thanx.
Oh, yeah -- I'm working with a Cingular 8525 Hermes [HERM100 model number] Pocket PC. It's specs are:
ROM version 2.15.502.3
ROM date 04/09/07
Radio version 1.40.30.00
IPL 1.03
SPL 1.11
Have you read this http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners ?
Re:
Yes, I have, plus all the links branched from there. After about 3 hours of reading, I felt ready to try flashing, but it didn't work. The HardSPL utility is done downloading, so when I get home I'll try that and hope I finally get a successful upgrade. If not, I'll be back to the forums. Thanx!
What ROM are you upgrading to? The official AT&T ROM? I'd try that first if you're not already.
BDsBabyGirl said:
Even after reading this forum all nite, I am still soooo confused, maybe too much new info in m'head. At any rate, I am trying to UG from WM5 to WM6 and am having a heck of a rough time. Everything goes good until it actually starts the process, at which time I get the 260 Connection Error. After plenty of research on here, I decided to try to "flash" the ROM, to no avail, for nothing happened. I can get into bootloader mode but then nothing else happens (perhaps I'm not waiting long enough? How long should I wait?) and I never see the screen pictured here - http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing - so I just give up and reset. I am currently downloading the HardSPL utility so I can try flashing after the IPL and SPL ugrades. But I do have some questions still --
(1) Does my phone need to be "unlocked" to do this and how can I tell if it is or isn't?
(2) Can I just use the ROM that I downloaded from the HTC site or must I use one found somewhere on this forum?
Any other advice? All will be appreciated. Thanx.
Oh, yeah -- I'm working with a Cingular 8525 Hermes [HERM100 model number] Pocket PC. It's specs are:
ROM version 2.15.502.3
ROM date 04/09/07
Radio version 1.40.30.00
IPL 1.03
SPL 1.11
Click to expand...
Click to collapse
What operating system are you using? If its Vista you MUST use Mr. Vanx's guide to get past the connection problem. The standard Vista HTC driver is wrong when we want to flash rom's in bootloader mode and vista WMDC. Get it here:
MR VANX's VISTA GUIDE
Hard SPL is great after that. Just remember you warranty may be void if you have to go to AT&T for repairs and the see that bootloader. You shouldn't need Hard SPL to flash the standard AT&T rom or VP3G's or other AT&T based ROM's, but better safe than sorry.
Be sure to close EVERYTHING in the taskbar! Don't start any programs, allow any updates to mess around with the computer while its flashing..In fact, I disable my AV program and internet connection totally when I flash ROMS. (My Kaspersky started updating and virus scanning during my 1st flash..sucker froze and freaked me out!)
Once I dealt with unlocking and connection issues, I flashed the standard AT&T ROM, performed a hard reset immediately and then connected via WMDC and synced everything. I tested it for a few hours then decided to flash VP3G's excellent AT&T based ROM v3.62.3..I like to do a hard reset immediately after flashing to burn everything in...I've seen others in this forum do the same.
Another ROM I've found fun is S64's(Starbase64) 3.62 WWE v9 - It's not AT&T based but you can get WPBEAR's Config files to set your Medianet and proxy. There are other At&T settings CABs out there like Dr. Puttinghams. S64 ROM also includes Advanced Config 1.1 to set your keyboard to Cingular mapping.
Good Luck!
re:
My desktop PC is running Windows XP...
After trying the HardSPL method - which upgraded perfectly - I continue to have the above-mentioned problems; 260 Connection Error and inability to move beyond the tri-color screen to the one pictured on the page which instructs how to flash via SD card.
Thanx for the list of ROMs I can try. For the record, I have been using the "official" one I downloaded from the HTC website. *sigh* I guess I'll next look for the tutorial I saw somewhere around here on how to upgrade from the tricolor screen [or something like that, I think it was], as well as your advice.
But I do have another question -- how do I format the SD card? The tutorial I used on flashing with it mentioned formatting so I'll retry it with the card newly formatted (I didn't because it said I could just delete everything off the card OR format it).
I'll let you know how it goes...
Ahhh...Sorry for your troubles...I didn't have luck catching an upgrade from the SD Card method on my 8525 either.
I know it seems a bit much but, is your active sync working correctly? Upgraded to 4.5 and all that? Can you sync and Backup all your data then try uninstal, reboot, re-installing AS?
I wonder what would happen if one tried Mr Vanx's instructions on a Win XP box?
I also had heard somewhere about messing around with when Active sync is started. Also as a last ditch, maybe try this from the HTC Wiki:
http://www.htcwiki.com/thread/667087/ActiveSync+and+Rom+8525?t=anon
Good luck
BDsBabyGirl said:
My desktop PC is running Windows XP...
After trying the HardSPL method - which upgraded perfectly - I continue to have the above-mentioned problems; 260 Connection Error and inability to move beyond the tri-color screen to the one pictured on the page which instructs how to flash via SD card.
Thanx for the list of ROMs I can try. For the record, I have been using the "official" one I downloaded from the HTC website. *sigh* I guess I'll next look for the tutorial I saw somewhere around here on how to upgrade from the tricolor screen [or something like that, I think it was], as well as your advice.
But I do have another question -- how do I format the SD card? The tutorial I used on flashing with it mentioned formatting so I'll retry it with the card newly formatted (I didn't because it said I could just delete everything off the card OR format it).
I'll let you know how it goes...
Click to expand...
Click to collapse
Just another tip... Try a different usb port. I've found that sometimes certain usb ports behave differently during the upgrade procedures. So, far I've upgraded three 8525's on Win XP and only one gave me the problem you've described and connecting the sync cable in another port corrected the problem.
Re: my Post
shihayadreamer said:
...I also had heard somewhere about messing around with when Active sync is started. Also as a last ditch, maybe try this from the HTC Wiki:
http://www.htcwiki.com/thread/667087/ActiveSync+and+Rom+8525?t=anon
Good luck
Click to expand...
Click to collapse
OMG! SHIHAYADREAMER! That was JUST the TICKET! I read it and realized that I'd been doing it right all along, I just didn't realize I was! THIS time, I hooked up my cable at the very beginning and let it go. Before, I'd started waiting to hook it up until the instructions asked if I had because I'd gotten to the tricolored screen (the bootloader?) the 1st time and figured I did something wrong. Thanx to that forum, I returned to what I did the very first time and got victory! *falls down sobbing and weeping with joy* I wasted 25 hours because of fear! OMG! *dances around, singing* I've got WM6! I've got WM6!
I know that being reminded to turn off my firewall and stop all the programs in the taskbar played a big role, as well. But I just give a big "Thanx" (on Thanksgiving! *LOL*) to everyone who answered this board because you all helped me so very very much.

HardSPL won't succeed

Hi All,
I'm new to the PDA-world and the Hermes. I'm trying to Hard SPL my Hermes, but it fails everytime.
When I run 2.10 - Hard-SPL-V7, it kills activesync and my connection is lost and I get always the message "error 260, Update error".
I have the latest framework edition and tried it on 3 pc's (1 Vista, 2 XP)...
What am I doing wrong?
Hope somebody can help me....
Kind Regards,
Micha
1). dont connect to active sync. open active sync and untick "allow usb connections".
2). put hermes into bootloader and connect to usb.
3). run ruu_wrapper.exe
should update to hard spl....
dont forget to tick "allow usb connections" again or you wnot be able to sync..
error 260 is an open port error.
if you wish to flash new os would advise to use sd card method. its safer than using the computer. just make sure you have greater than 50% battery power. happy flashing
Thnx, will give it a try.
First I have to flash HardSPL before I can flash a new OS, don't I?
yep, sorry, should have said run the ruu_wrapper for hard spl. My bad...
im having the same problem. I also tried the way ultramag recommended but i also received the same ending. After time i try i get the Error 260 Update error. Im running SPL 2.04 and the HTC WM6 rom from the HTC website. Does any one know what the problem is?
ultramag69 said:
2). put hermes into bootloader and connect to usb.
Click to expand...
Click to collapse
NOOOOO, that won't work, you need the SSPL to deploy to the phone, if you're running stock HTC bootloader this won't work at all, otherwise we'd have no need for Hard-SPL
hey olipro, then how would i fix this. Im running the stock rom from the HTC website with no hacks. Im trying to load PDA Corners V9 rom. Any ideas on how to fix? thanks!
Take a peek at the guide i wrote about updating the hardspl. Theres some explanation about why we need to use SSPL and the procedures.
http://www.mrvanx.org/hermes_guide/hardspl
thats the guide i used. it still gives me the error. I even unchecked "allow connections" cause i read somewhere that that would help.
i did this two days ago on my phone, im running windows vista on my home laptop and got any number of errors and problems trying to do it via sync with the phone (even after reading the vista troubleshooter, with the drivers etc)
What i ended up using was the memory card upgrade, dump the file onto the memory card and go into bootloader with the card installed.
worked fine doing that way, maybe less risky as there is no chance of the usb cable coming out.
just make sure you have a good battery charge on the phone.
Help Help Help w bricked 8525
I got into this position trying to upgrade WM5 to WM6 from HTC site.
Process got to 20% and just stayed there.
I reconnected usb cable and got a vendor id error
Then I get the Error [260]: CONNECTION
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
I believe this is the bootloader? I have downloaded RUU_signed.nbh, renamed it to hermimg.nbh, installed on root of my SD card and held OK, soft reset and power button:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
All post indicate that the device can be reflashed and have the OS reinstalled. I can't get there from here.
Can anyone please help?
blackdog9692 said:
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
Click to expand...
Click to collapse
How big is your SD card? Flashing only works with cards <2GB. Also, sometimes certain cards just don't work for flashing, and just swapping to a different card fixes the problem.
I assume you searched the wiki, and found the relevant pages on the Hermes (including SD Card Flashing and other things about flashing/upgrading) there?
Still Lost
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen. When i attempt to flash the rom via PC to WM5 or WM6 i get the Error 260, i also get a vendor ID error sometimes.
How can i find the key 8525 thread that i am told has the answer to my delima? I keep picking up bits and pieces but am missing some key steps and tips.
blackdog9692 said:
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen.
Click to expand...
Click to collapse
That sounds like the SD card is formatted incorrectly. Make sure it's formatted using fat32, nothing else will work.
Still not there from here
Thanks for your help. Before I formatted the SD FAT32, nothing would happen doing the bootloader reset. OK/ON/reset button.
After format and only the hermimg.nbh file renamed as indicated, I then get what looks like the loading process but back to the bootloader screen.
Q1: This is an AT&T 8525, it was perfectly fine before failure from WM5 to WM6 (process froze at 20%), what is the RUU file that I need to put on SD??
Q2: After "Loading ..." I try the WM5 PC upgrade of ROM via USB cable, I get the load process to appear to work but it gets to 1% and the phone reboots and the PC reports error [294]: Invalid vendor ID. If I do this again I will get the Error [260]. Ive repeated the process several times.
Is this the normal course to take or should the "SD Method" (with the WM5 or WM6 RUU.. file) complete the process to a working OS?
Q3: Is my situation hopeless? ATT will take my out of warrantee 8525 and reflash for $129. Reading the threads it seems that like me this can be done by me, this is my desire.
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
The newbe guide has been off line. I will look again. Is there a single place to read about "radio PDAs and the 8525 and understand the software build and custom options?
Sy for the long post. But still want to fix if possible or I will be force to mail in for ATT repair.
Thank you all.
blackdog9692 said:
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
Click to expand...
Click to collapse
Oh boy, you haven't installed HardSPL? You are walking a bit of a line there mate...
HardSPL is a custom boot loader that makes bricking your phone when flashing much harder to do, and helps large amounts in the recovery process if you phone does brick.
Does the phone boot at this point? If so, do not try flashing the phone again. Go get a copy of HardSPL and install it, then try flashing from the SD.
I still wonder why people didn't read before bricking...
Anyway, you should start reading now and wiki is your friend. Your SPL is 2.03, so look at the bottom of the page (there is only one solution till now, so good luck with that):
Code:
1. Boot OS using KITL+PB
2. Do no disconnect your HERMES till the end of the step 6
3. Download SSPL on HERMES by wifi from ie explorer
4. Launch SSPL then flash Hard-SPL from your computer
5. Put your hermes in bootloader mode
6. Flash any radio in NBH format from your computer
Still researching and working this bricked 8525
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
I then put it on an SD card and held the keys and reset. The device displayed a white screen and "Loading..." appeared. Afterward the 8525 returned to the stipped boat loader screen and that is where I am now.
Some of the help i receive and read on wiki threads has me confused with what to do next and how "exactly" to do it.
It does seem that I am not alone and people have fixed their phones and the process to do this is on the forum. I'm just still missing something.
Help me further if u can.
Thank you.
blackdog9692 said:
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
Click to expand...
Click to collapse
FYI: bad form to PM someone and post the same thing here. Keep it in the thread so others can be helped as well.
As I replied in the PM, if I'm understanding your post correctly, the phone boots to the tri-colour screen?
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
jdc said:
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
Click to expand...
Click to collapse
We already know that the phone is without HardSPL, according:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
Click to expand...
Click to collapse
There is small chance (read my previous post) to unbrick device with SPL2.03 so better try to get this back from where you take it.
And please, change topic, because this brick isn't HardSPL fault at all.
Edit: oh dear, it's even not your topic ...good game, I'm off

[Q] How to "unbrick" HD2?

Hello,
at first I like to say, that I've read lots of threads concerning freezes, false flashed roms, etc. but I don't found a thread which deals with my problem. In fact of this I opended a new thread.
What is the problem?
- The HD2 hangs up with a white screen while booting.
What things are still working?
- I'm able to go into bootloader mode (Vol-Down + Power)
- I'm able to get a USB Connection through the bootloader mode
The self analyzed main problem
- I've got a broken Radio Rom
- I've got SPL 1.42 (no HSPL)
What I've tried
- I tried to flash a Rom due to CustomRUU (Cooked & Ship Rom)
-- Effect: No success. Hang's up at 0% (I think due to SPL)
- I tried to flash a ROM by SD-Card over bottloader.
-- Effect: It load's the setup. Trys to install, but fails with the Radio part. (Radio Update failed)
- I'm able to get in MTTY an do a "Task 29". And try to flash again.
-- Effect: Task 29 works well. But flashing still fails at RadioROM Update.
- I've tried to get a connection to the WMDC and try to flash over UpdateUtility
-- Effect: The WMDC doesn't recognize my HD2. (Even if the bootloader menu shows up a USB connection.)
- I tried to get HSPL (1.42, 1.66, 2.08). I tried all versions. HSPL, HSPL2 & HSPL 3.
-- Effect: HSPL finds my HTC. I can select the version. But while flashing HSPL it stop with an critical error. (Flow: 00000006 Errorcode: 00000014)
So is there anybody how knows a way to restore my RadioROM? I tried lots of things but now I really don't know what to do.
I hope you can understand me (incause of my english skills) and that you'll have some more ideas.
With best regards,
Raffi
Lets wait for the pro's advice!
But if u can access bootloader, not all is lost.. and HD2 is not bricked
I had nearly the same Problem. The only difference was that i could install HSPL.
Something you can try: disconnect the battery for some hours and then flash from SD-Card. After some tries i got mine back to work
netblognet said:
- I've tried to get a connection to the WMDC and try to flash over UpdateUtility
-- Effect: The WMDC doesn't recognize my HD2. (Even if the bootloader menu shows up a USB connection.
Click to expand...
Click to collapse
that's correct, it doesn't need to connect to wmdc, when they say to get an activesync connection, they only mean a usb connection. if you start the update whilst it IS connected to wmdc, the first thing it does is disconnect and then put the phone into bootloader. you are helping things along by entering bootloader yourself. a little confusing.
that being said, i suspect it won't work. i've seen a few threads where the radio prevents anything flashing, and they never seem to conclude to anyone's satisfaction.
i would probably go for the goldcard method, but you might need a working winmo phone to get the sd cid. an eveningsreading ahead of ya.
Esquilax said:
Something you can try: disconnect the battery for some hours and then flash from SD-Card. After some tries i got mine back to work
Click to expand...
Click to collapse
I'll try that. And tell you what happens.
samsamuel said:
i would probably go for the goldcard method, but you might need a working winmo phone to get the sd cid. an eveningsreading ahead of ya.
Click to expand...
Click to collapse
I really don't know, but I think I've got a goldcard. So I've 2 micro-SDs. With the first I'm unable to flash anything. The second I made goldcard some flashs ago. I really thought Goldcard would be only work for one flash. But with the second sd-card, which I made goldcard once ago, I'm able to initiate a flash. (But it stops at the Radio-Update.)
Question 1:
How to proof if it's a Goldcard.
Question 2:
I've heard about "JTAG". A saw that it's a piece of hardware. Are there any reports, at this moment, about successful repairs of HD2s with JTAG?
1 no idea, but i do know it stays gold until you format it.
2 there are a few threads about it, look in the tmous section, there are one or two in there too.
i thought it might not help.
have a browse through previous posts by xmoo, he has helped some situations regarding a stuck radio, though no promises.
netblognet said:
Hello,
at first I like to say, that I've read lots of threads concerning freezes, false flashed roms, etc. but I don't found a thread which deals with my problem. In fact of this I opended a new thread.
What is the problem?
- The HD2 hangs up with a white screen while booting.
What things are still working?
- I'm able to go into bootloader mode (Vol-Down + Power)
- I'm able to get a USB Connection through the bootloader mode
The self analyzed main problem
- I've got a broken Radio Rom
- I've got SPL 1.42 (no HSPL)
What I've tried
- I tried to flash a Rom due to CustomRUU (Cooked & Ship Rom)
-- Effect: No success. Hang's up at 0% (I think due to SPL)
- I tried to flash a ROM by SD-Card over bottloader.
-- Effect: It load's the setup. Trys to install, but fails with the Radio part. (Radio Update failed)
- I'm able to get in MTTY an do a "Task 29". And try to flash again.
-- Effect: Task 29 works well. But flashing still fails at RadioROM Update.
- I've tried to get a connection to the WMDC and try to flash over UpdateUtility
-- Effect: The WMDC doesn't recognize my HD2. (Even if the bootloader menu shows up a USB connection.)
- I tried to get HSPL (1.42, 1.66, 2.08). I tried all versions. HSPL, HSPL2 & HSPL 3.
-- Effect: HSPL finds my HTC. I can select the version. But while flashing HSPL it stop with an critical error. (Flow: 00000006 Errorcode: 00000014)
So is there anybody how knows a way to restore my RadioROM? I tried lots of things but now I really don't know what to do.
I hope you can understand me (incause of my english skills) and that you'll have some more ideas.
With best regards,
Raffi
Click to expand...
Click to collapse
Flash through usb your mama rom, I mean the rom which had the phone originally from factory.
Esquilax said:
I had nearly the same Problem. The only difference was that i could install HSPL.
Something you can try: disconnect the battery for some hours and then flash from SD-Card. After some tries i got mine back to work
Click to expand...
Click to collapse
I've tried it. No difference to before.
samsamuel said:
1 no idea, but i do know it stays gold until you format it.
Click to expand...
Click to collapse
I've formatted the card, but then there the question why I'm able to start a flash with these ex-gold-card and why I'm unable to flash with the other card. Both are 2GB and both are fresh formatted.
NIKOSXRI said:
Flash through usb your mama rom, I mean the rom which had the phone originally from factory.
Click to expand...
Click to collapse
Nice tip, but to my detriment i don't know which version exactly was the shipped one. I received one of the first HD2 in germany from tmob. I think it was something 'bout 1.43.But I really don't know. And you're sure that the original ROM will refresh the broken Radio?
is one sd card bigger than 4gb? 8 and especially 16gb cards are not much use for flashing.
netblognet said:
... Both are 2GB and both are fresh formatted...
Click to expand...
Click to collapse
Like already said, both are 2GB SD-cards.
I think the problem arised because you tried to flash a custom ROM without HSPLing (or Gold Carding or SSPLing) first.
You don't need the origional shipped ROM, all you need is to go to HTC Germany's site and download a T-Mobile ROM. You can either put your phone into Bootloader Mode, connect to your computer and run the ROM exe file or use the SD Card method.
It should flash properly and you should have the T-Mobile Germany ROM, RADIO and SPL.
In future if you want to flash a ROM, then read the chef's instructions. If you are sure you want to flash that ROM, then read the instructions again.
Nice tip, but to my detriment i don't know which version exactly was the shipped one. I received one of the first HD2 in germany from tmob. I think it was something 'bout 1.43.But I really don't know. And you're sure that the original ROM will refresh the broken Radio?
Click to expand...
Click to collapse
This is a solution for sure, I had the same problem.
Search in tmobile site or ask them for their first german rom.
Ok, I downloaded a Original Tmo-Germany ROM from HTC. But same errors. Over Update-Utility >> Error 262 at 0% after some minutes. Over SD-card: Update starts. Progressbar runs. And then >> Radio_ failed.
netblognet said:
Ok, I downloaded a Original Tmo-Germany ROM from HTC. But same errors. Over Update-Utility >> Error 262 at 0% after some minutes. Over SD-card: Update starts. Progressbar runs. And then >> Radio_ failed.
Click to expand...
Click to collapse
You must try the old-first tmo german rom that they loaded in the phone.Not just a tmo german rom!
When I had the same problem and I flashed a current rom, the problem remained until I flashed the first old rom.
Ok, I got the first and original rom. But it also fails at the Radio Update. But i found a friend of my friend who's got a HD2, too. So i'll try it with the goldcard method...

Categories

Resources