Bricked Hermes Whiles upgrading to Imate telstra WM6 rom - helppppppppppp - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

I have a jasjam
i was upgrading it using the telstra WM6 rom.
during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
it the first splash screen it shows no gsm
it only shows the bootloader menu
IPL 1.04
SPL 2.03
i read the wiki on how to unbrick a bricked hermes but there is no sulotion
plzzzzzzzz
anyone can help me??????

koorosh_bsboys said:
I have a jasjam
i was upgrading it using the telstra WM6 rom.
during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
it the first splash screen it shows no gsm
it only shows the bootloader menu
IPL 1.04
SPL 2.03
i read the wiki on how to unbrick a bricked hermes but there is no sulotion
plzzzzzzzz
anyone can help me??????
Click to expand...
Click to collapse
Did you also read the wiki to see how to install hardspl to protect your device BEFORE flashing ?(here: http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27 )? Are you using Olipro hardspl?
Try to use the SDCARD method (Format a sdcard in FAT32. Copy the nbh file on it and rename it HERMIMG.NBH. Insert the card and HR : OK/POWER/Soft reset. Follow the instructions)

i tested that but didn't help
does anybody have any suggestion??

Try solution to reeboot ( sometimes helps)
1. get out SIM and SD card
get mtty http://forum.xda-developers.com/download.php?id=9864
2. Make BL mode on Hermes
2a on PC ActiveSync - coonection properties untick allow to connect by USB
3. start mtty on PC , choose USB and enter.
4. next enter.
5. type set 14 and enter
6. type task 8 and enter
OS have to boot if no go to 7
7. enter
8 type set 16 and enter
9. type task 8 and enter
Hope that will boot

http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Pretty much all the info on unbricking is in this table by Pof. If this doesn't sort you out then you're have to send it off to imeicheck etc for repair.

The history so far
I have bricked my jasjam while updating to telstra wm6
I have not super CID my device before upgrading to telstra wm6
Now my device freezed at second splash screen
IPL 1.04
SPL 2.03
NO GSM
when i used the info 6 command on mtty it says NO CID
i can not upgrade my device from SD CARD (memory stick)
i used these command on MTTY.exe but no improvement
set 14
task 8
set 16
task 8
when i tried to rom upgrade using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
any suggestions????

I hope you understand this, Basically if
1. You have a "No GSM"
2. Your CID is corrupted
3. Your OS has no KITL mode
4. You didn't use HARDSPL...
Then your phone is screwed, and you need to buy a new one or send it to repair.
Hope you have better luck with your next phone. (you seem to be collecting bricked phones!)

Wam7 said:
4. You didn't use HARDSPL...
Click to expand...
Click to collapse
That's the BIGGEST mistake u ever made with ur Jasjam, bro
try to send to repair centre, if repair cost is too much. Than u have to decide try but new gadget. Kaiser looks flirt to me

yep im glad i waited to upgrade from the proper wm5 to the proper wm6

st3v3 said:
yep im glad i waited to upgrade from the proper wm5 to the proper wm6
Click to expand...
Click to collapse
Did u mean, u stay at proper WM5 or already Flash to WM6 ?
I think everything is save IF we read carefully the disclaimer from the author

ermenzegna said:
Did u mean, u stay at proper WM5 or already Flash to WM6 ?
I think everything is save IF we read carefully the disclaimer from the author
Click to expand...
Click to collapse
The offical I-mate telstra Jasjam rom for WM6 came out recently previous to that i just kept the original WM5 rom that it came with much to the dismay of my peers, actually considered it a few times but decided against it till the official rom came out.
yeah if you follow the instructions for the WM6 rom you use it should be ok however the "Murphys law" of programming tends to suggest there will always be an error that they dont allow for.

st3v3 said:
The offical I-mate telstra Jasjam rom for WM6 came out recently previous to that i just kept the original WM5 rom that it came with much to the dismay of my peers, actually considered it a few times but decided against it till the official rom came out.
yeah if you follow the instructions for the WM6 rom you use it should be ok however the "Murphys law" of programming tends to suggest there will always be an error that they dont allow for.
Click to expand...
Click to collapse
This has NOTHING to do with only using official Roms! One has pretty much the same chance of bricking their phone evening using an official WM6 as a cooked variant from Schaps et al..
Simply put if you don't use HardSPL then you're asking for trouble no matter what the ROM. You should also use the MicroSD wherever possible as it is much more reliable.

imei check use jtag to fix this
imei check use jtag to fix this ,CAn we use jtag to fix this in hermes. need help to resovle spl 2.03 cid locked no gsm.

Related

WM6 Upgrade Guide

How to upgrade from WM5 TO WM6
To upgrade your prophet to WM6 I recommend that you first of all downgrade to the NVID version of WM5 AKU2.2 and get the latest Active Sync:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe YOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com
3. Install active sync, you might need to reboot
4. When your computer has rebooted, run the file from step No 1 . Follow the steps, remember that it can take some time and seem to stuck at 80% and higher, but just wait.
5. When you have done this, your pda will reboot. After it comes with the welcome to windows mobile screen,"Tap Here To Begin",JUST LEAVE IT. In fact don't touch your device before the next steps are finished.
6. Now download one of the WM6 versions( http://forum.xda-developers.com/showpost.php?p=1279985&postcount=1 )
7. Now find a file named Upgrade.bat,and run it.(you don't have to run Step1 of PdaMobiz or PDAViet Temp,as you have already downgraded to AKU2.2)
8. Wait until the upgrade finishes(usually takes 12-15minutes)..WAIT WAIT WAIT
9. A message will be displayed in the dos box,and it will say that the upgrade is finished etc....etc...,now you HAVE to HARD RESET,to finish the upgrade and enjoy you new WM6!
How to downgrade from WM6 TO WM5
The downgrade process from WM6 to WM5 is pretty simple. All you have to do is to downgrade to WM5 NVID and after that upgrade to the WM5 you want:
1. Download the NVID(no vendor) AKU 2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exeYOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com.. Simply search for "Active Sync"
3. Install active sync, you might need to reboot
4. When your PC is ready run the NVID file you downloaded in step1 and follow the guide, remember that it can take some time and seem to stuck at 80% and higher, but just wait
5. When its done downgrading to the NVID WM5 rom, you prophet will reset and you can upgrade to the version of WM5 you want.
NOTICE
If you use a different AKU 2.2 ROM(like PDAViet Temp),you may have two EXEs in the folder you extracted.Be careful and use the one that is made for your device:
FILENAME G3.EXE
is for G3 devices:IPL x.xx.0000, SPL x.xx.000.0 (this is shown when you reset)
FILENAME G4.EXE
is for G4 devices:IPL x.xx.0001, SPL x.xx.000.1 (this is shown when you reset)
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
How to switch or upgrade/downgrade between WM6 versions(for example PDAViet->Trueneytral)
1. First you have to downgrade to WM5 AKU2.2 using the WM6->WM5 guide(some say that you don't have to do that,but i believe that it's better to downgrade first rather than making a simple overwrite)
2. Now follow STEP 5 of the WM5->WM6 guide
Device doesn't connect to PC after flash
If your device doesn't connect to your PC after flash,just enter bootloader(press camera button+while pressing soft reset and hold,until a tri-color screen shows up),and flash the NoVendor WM5 Rom: http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe .Then repeat the whole process...
----------------------------------------------------------
KEEP IN MIND:
UPGRADING CAN BE DANGEROUS,YOU ARE RESPONSIBLE FOR THE DAMAGE TO YOUR PHONE
DO NOT RESTORE BACKUPS FROM ANY ROM OTHER THAN THE ONE IT WAS CREATED ON
THERE IS NO "BEST WM6 ROM",THE BEST IS THE ONE THAT WORKS BEST FOR YOU
(part of the guide is taken from Da9L's guide,in the WM6 Rom Collection)
I will edit/update this post soon and clean it up, ask questions in another thread, and by god please read the wiki first, 90% of the questions asked are answered in the wiki....
WM6 Upgrade Guide...reply
great info sir! thanks so much! downloading...i'll be happy to send feedbacks on this WM6 ROM! thanks again!
Thanx a lot tonydeli7 , very very good guide and a lot of ppl really needed it
Great
Thanks to you all. I have Qtek S200 and trobuled with WM6 it wonderfull guide for me thank you very much.
I need to downgrade to WM5, 'couse I cannot boot anymore. After running the setup I get an error that the device cannot be found. I have connected the S200 with the boot loader running.
Edit: Now it works on an "old" WinXP machine.
Huge Problem!!
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
dharvey4651 said:
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
Click to expand...
Click to collapse
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
I followed the instructions carefully, and my phone (Qtek S200) seemed to boot with WM6.0
However, after aligning screen, it tried to initialize the phone with some extended roms, a procedure which failed, and I had to soft reset.
After reboot, it seems to work fine.
Is it?
EDIT: Another thing I noticed is that keyboard is in THAI !!! How can I make US the default? Olso, I have Resco keyboard GR edition. Will this work with WM6?
tonydeli7 said:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Click to expand...
Click to collapse
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
yoda_143 said:
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
Click to expand...
Click to collapse
i don't know mate.i believe you can use pdaviet's temp instead of aku2.2 nvid...
Another thing I noticed, is that it looses pairing with my bt handsfree...
I am making the pairing, and works fine. However, when at night I am shutting off my hf in order to save battery, the next morning the pairing is gone.
Any solution to this?
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
dufchan said:
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
Click to expand...
Click to collapse
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
I-mate Jamin
hello evrybody
i just wanted to know if i can upgrate my WM5 to WM6 on my I-mate JAMin?
rondol1 said:
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
Click to expand...
Click to collapse
thank u very much!!now my dopod working fine!!thanks a lot!!
thanx for the guide
help me please..
P4k1t0 said:
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
Click to expand...
Click to collapse
how to do that?
thx..
Choice of ROM
Hello guys, tanks for a so nice job !
I would like to have more information about the choice of ROM.
I don't want any special feature, just the row wm6.
no programs added, no tweaky today, no bugs, no battery problem, etc etc
which one would fit that the best ?
thanks
Thnx for this man, much appreciated!

Please help.. a little girl waits :(

Heh apologoies for title but im really stuck and desperate for any help!!
I have been trying to unlock my Cingular 8525 for many hours now without any luck.
I bought it off ebay knowing it was locked because I had seen these forums and knew it wasnt too harder job. I live in NZ we have a compatible 3G network here (they sell these phones branded as JasJams).
Anyway I dont have a cingular sim card, only a Vodafone NZ simcard. I dont know if that is a problem for me or not...
My problem is that I get part way through the update process and the connection between pc and phone gets cut everytime at the same place.
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
It then gives me the button to select the Update button (Update the radio and bootloader)
So I click that, it gives the next screen, click next, tells you its going to take 10 minutes etc, so click next,
It then instantly disconnects the active sync connection and about a minute later I get an error screen saying the unlocker encountered communications errors.
I have been through this whole proccess 6 times now with no joy
Someone pleeeeeeeeease help me
Thanks
im willing to pay for a code all i want is a unlocked sim phone none of this radio stuff etc
try Wiki
http://wiki.xda-developers.com/
or alternatively
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
Thanks but not really helpful, I have read the wiki through and through. I have tried that flashing HardSPL v7 and i get exactly the same problem.
PLEASE somebody help me
The only piece that is confusing is what to do once your done. The instructions say that you will be replacing your radio with a tweaked one to allow the unlock. After the entire process is done I assume you will need to have your favorite radio (1.40.3 in my case) handy to flash back onto your Hermes?
I also assume that flashing your favorite radio back to the Hermes won't lock it back again.
To be honest, I'd suggest going back to basics. You could try quite a few workarounds and end up doing this anyway..:
Reflash the original ROM your phone came with. Should be found easily via wiki.
Then you can start upgrading again.
If that's difficult, try flashing from your MicroSD card, which I've found never fails, having bricked my Hermes quite a few times now with my own cockamayme (sp) versions of ROMs that I've cobbled together from bits of code and chewing-gum.
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
amet said:
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
Click to expand...
Click to collapse
She want's to SIM-Unlock, not to CID-Unlock.
Do you use Vista? I encountered a similar problem with Windows Vista. Try a PC with Windows XP for the unlocking process.
ok my bad....
I've seen this issue with v1.4 Olipro. Upgrade bootloader to the latest Olipro 2.1 version then re-attempt.
ok thanks everyone for your advice but i am still screwed.
im not running vista.
i can not upgrade to olipro 2.1 because the upgrade utility always gets error 260 (update error) the update utility cannot connect to your PDA Phone.
I have now tried on 3 computers, my own, my parents and my work all resulting in the same thing.
I think now I will try and flash a WM6 rom onto my phone just using the olipro 1.4 and the custom RUU updater and see how I go but I dont have much hope
ok im currently updating the rom to wm6 as posted on the forums and oh my gosh i have a progress bar for the first time ever!! woot~~
um ok. now i have WM6 dopod version and fkn still sim locked someone help me before i throw my phone at the wall lol im going on holiday tomorrow and will have no phone for a week if i dont fix this in the next 3 hrs
Sim Unlock
http://forum.xda-developers.com/showthread.php?t=293665
laurasaur said:
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
Click to expand...
Click to collapse
Do *NOT* soft reset your phone here, it is normal that activesync disconnects while the pda is in bootloader mode (activesync only works while OS is running). Just click "next, next, next" in the RUU and it will go fine.
woooa i think i love you Pof, I seriously do. Im not sure how I became such a noob at reading instructions but im sorry and thank you so much I now have progress bar
if you're short on time avoid any radio updates, they seem a bit hit and miss - its not worth upgrading then going away to find you've got a tossy signal!!!!
hope it worked out!

MTTY's "wdata" cmd unlocked on SPL 2.03!Can it Unbrick the bricked ones w SPL 2.03??

MTTY's "wdata" cmd unlocked on SPL 2.03!Can it Unbrick the bricked ones w SPL 2.03??
I have found a way to unlock "wdata" command in bootloader 2.03!
summary:
In bricked hermeses with SPL 2.03 - NO GSM - KITL disabled, the wdata command is locked. I am not good at programing but I want to know if it possible to change the SPL(bootloader) of bricked hermeses with this command in mtty.exe??!!
How to:
1.Use the trinity splxploit -windows by pof (unbrick.bat). Let the program run for some seconds and then just close that.
2.Do not unplug the usb or soft reset the device.
3.Run mtty.exe and type "wdata" the command is unlocked!
I wanna know can we erase just the CID by erase command and write a CID value using wdata command?
If it can be done then we can unbrick our hermeses!
Yes it enable wdata, you don't need to change CID, if you can load OS.nb, then from Windows use SSPL. But real problem is how to load OS.nb via wdata
need Hermes splxploit -windows ??
i many time write in this forum who can unbrick hermes with spl 2.03 cid locked,no kitl,can not boot,stack in bootloader....only solution is that pof
or good man create Hermes splxploit -windows this will jump spl address and temporaly cid unlock Hermes then we can flash any rom.
I unbrick many Trinity bat wait solution for Hermes???
Bat wait ........and wait.
Zemo znas li ti kako da sredis brikovan hermes cid zakljucan spl 2.03...itd.
Yes, we need pof help, it will be very good to have spl exploit for hermes.
Bas nas dosta ima na XDA, mozes samo preko JTAG koliko je meni poznato ali neznam nikog ko to moze da uradi. Odakle si?
Yes, we need pof help. It will be very nice to have SPL exploit.
Mislim da moze preko JTAG, ali neznam ko to moze da uradi, odakle si?
Bad news people,
The memory layout on hermes is different than on trinity, i already looked
into this and is not possible to exploit it in the same way as I did in
trinity.
I am sorry but I have no time to invest on this now
Best Regards,
pof
Click to expand...
Click to collapse
We can wait for pof, and pray
So, we will wait.......!
I'm a prayer too
So, we will wait.......!
I'm a prayer too
Reply With Quote
Click to expand...
Click to collapse
MY HERMES IS BOOTED OS TODAY!!!
It was half dopod and half T-Mobile...
T Mobile Customanisation: Instalig Dopod stuff???
I soft reset it and it stuck again.
Booted OS
Today my hermes booted os, after soft reset it stuck again. But there is hope, right?
Can you solve No GSM with SD Card Flash?
Then Copy Hardspl V7 to the sd card and when your mobile booted into os just run that from your device.
Yes, I know that.
If you have similar problem:
1.Leave Hermes without battery for some time, hour or so.
2. DO NOT turn it on, do a HARD RESET*
*If don't work try several times
hardspl v7 or any other after 100% message image corupted
koorosh_bsboys said:
Then Copy Hardspl V7 to the sd card and when your mobile booted into os just run that from your device.
Click to expand...
Click to collapse
Yes i know this bat this will not work if hermes cid locked and stack in bootloader no kitl and gsm.Can not boot os this only work in hermes cid unlocked device then sd card work...bat what i can do when device cid locked and can not connect in activsync and everytime when try to use hardspl v7 or any other after 100% message image corupted only solution is that pof create jumpspl pach that work from dos without activesync this can help me and many other i will donate with paypal if somebody can creat this that work in hermes......
............again harmes how to unbrick 2.03
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
If somebody else create solution before me please sent me message to know??
Do not post any solution from this site i try all and not work(SD card will not work when cid locked,hard spl-not work always 100% then message image corrupted,No kitl.....so please only original solution not from xda-developers..etc.
thanks for all.
Pozdrav zemljacima iz Srbije.
Pozdrav,
Ima nas prilicno sa SPL 2.03...
Igor
gsmhackerns said:
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
....
Click to expand...
Click to collapse
Glad to hear that.
I am sure that the sulotion for spl 2.03 exists, but we don't know where to find it.
BTW, where is POF & olipro????
I made some progress, it stuck at OS screen now. It booted os several times today, it is strange that it can boot OS it is IPL 1.04 SPL 2.03. Stil NoGSM
koorosh_bsboys can you hermes boot OS?
Can NoGSM problem be solved with Flashing from SD Card?
igord said:
I made some progress, it stuck at OS screen now. It booted os several times today, it is strange that it can boot OS it is IPL 1.04 SPL 2.03. Stil NoGSM
koorosh_bsboys can you hermes boot OS?
Can NoGSM problem be solved with Flashing from SD Card?
Click to expand...
Click to collapse
My hermes can't boot into OS. It has stucked on 2nd splash screen (Imate telstra logo) not the OS logo!
How can u boot into OS?
If you find something new then share it with us.
My HERMES sometimes stuck at second boot scree and sometimes at windows screen, but few times it booted os. Than I put SSPL at microSD, becouse it stuck after few sec when it is on USB. OS is working ok - then I killed it again to SPL 2.03 and today get it back to working OS, No GSM.
What I did to get working OS???
1. Get battery out for about a day.
2. Put the battery in, DON'T POWER ON!!!
3. Do a HARD RESET.
If it don't work try several times.

Qtek s200 IPL/SPL

Hi
I have qtek s200 never locked on any network
I have downloaded ROMUpdateUtility_NV_G3 and G4
But after i done to see 3 colors i have doubt i what G3 or G4 update rom to use
IPL 2.09
SPL 2.09.0000
gsm 02.07.20
os 2.9.7.24
My question is which Rom to user G3 or G4, or i have to do something more before runing RomUpdate
tnx in advance
By this link
http://wiki.xda-developers.com/index.php?pagename=prophet_g3g4_how
It might be G3
but not sure because my IPL 2.09 without anythin after that .09
but with 4 zeros after.09 in SPL
that is normal "fake boot", freezed screen because you didn't make the HardSPL,
yes, its a G3,
read my thread..... read man, read post 1 is ok
enjoy
dioxda2 said:
that is normal "fake boot", freezed screen because you didn't make the HardSPL,
yes, its a G3,
read my thread..... read man, read post 1 is ok
enjoy
Click to expand...
Click to collapse
That's the case
I didn't do anything. This is factory setup
This is never locked on any network Qtek . it works 100%.
I just want to upgread it to WM6
Bakudan said:
That's the case
I didn't do anything. This is factory setup
This is never locked on any network Qtek . it works 100%.
I just want to upgread it to WM6
Click to expand...
Click to collapse
1. "old method" for "old roms"
= Flash PVtemp (everytime), then upgrade wm6 (must follow my steps.......in my post),
2. "new method" for "new roms"
= Flash HardSPL (only needed once), then upgrade to wm6 or 6.1
ok now?
Bakudan said:
That's the case
I didn't do anything. This is factory setup
This is never locked on any network Qtek . it works 100%.
I just want to upgread it to WM6
Click to expand...
Click to collapse
That iS the point! You HAVE to prepare your S200 first before you can upgrade to WM6. With only factory defaults you are NOT able to succeed.
So I second dioxda2's advice:
read all the guides, WIKI's and other relevant information here before you dive into the deep... But hee, afterall its your phone....
rondol1 said:
That iS the point! You HAVE to prepare your S200 first before you can upgrade to WM6. With only factory defaults you are NOT able to succeed.
So I second dioxda2's advice:
read all the guides, WIKI's and other relevant information here before you dive into the deep... But hee, afterall its your phone....
Click to expand...
Click to collapse
So if i download gullum ROM Prophet XB
First to do ROMUpdateUtility_NV_G3.exe
and after that Upgrade_ROM.bat
if i get it correctly
i did hardspl
and after i'm trying to install touchXB i get
Copying C:\DOCUME~1\MARKO~1.TEK\Desktop\QTEK\PROPHE~2\itsutils.dll to WCE:\windows\ItsUtils.dll
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart activesync
tryed restarting device and ms sync
i get the same stuff
Bakudan said:
i did hardspl
and after i'm trying to install touchXB i get
Copying C:\DOCUME~1\MARKO~1.TEK\Desktop\QTEK\PROPHE~2\itsutils.dll to WCE:\windows\ItsUtils.dll
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart activesync
tryed restarting device and ms sync
i get the same stuff
Click to expand...
Click to collapse
this is a common error when the pathname is to long. Copy the Folder to your rootdirectory (C:\) of your PC and run upgrade.bat from that location.
tnx
this time everything went OK
i enters setup set up password and now is not ok..
it wont accept it
Bakudan said:
tnx
this time everything went OK
i enters setup set up password and now is not ok..
it wont accept it
Click to expand...
Click to collapse
That too is a common problem, with this version of WM6 password just don't "stick". The problem is with all WM6 ROM's of that generation, not only the one you flashed. There is no solution, just don't use a password. The newest ROM's seem to have solved this issue, but I can't confirm that because I don't use a password anyway.
So, now you are stuck. Do a Hard Reset and configure your device again.

for all dead prophets

i saw lot of people have dead prophet problem, so i am here now to make a new thread to all this people and i hope to make it useful.
now we start
** FIRST : lets know names of prophet :
I mate Jamin, O2 XDA Neo, Qtek S200, Dopod 818 pro, Dopod 830, SPV M600, VPA Compact S.
** SECOND : we must know that before we trying to do any updating or change roms on my prophet i just need to do which called unlock for the prophet and then we after that been able to change any rom on my ( jamin ) and of course u need to be careful about Your device is it G4 or G3 ,
# and how we know its G4 Or G3 ?
# when u start Your Device u will see some numbers on left,
---------------------
IPL: 1.00.000
SPL: 2.20.000
GSM: 02.61.21
OS: 3.0.0.0
--------------------
and may be changed and that goes to the rom which You have, now we look for the last number on ( IPL and SPL ) , if we found it ( 0 ) it means You r G3 and if it ( 1 ) so You r G4 .
** THIRD : lets go to unlock , i will put programs in this thread it will help u in unlock.
-- Sync your device with computer and open the file u download it called HardSpl you will find two files one one foe G3 and G4 open your kind then you'll find a file called (( hardspl.bat )) okay, be sure your device is connected to computer then open the file and follow instruction and it will reset your device ,
now u ready to change rom.
TO BE CONTINUED
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
if any one can help please contact me.
hello
my device is jamin g4
it stopsat the boot loader and dono thing
can u help me please?
my e-mail is [email protected]
and suddenly after trying to update the spl been 1.01
please help me
can i fix it?
waiting for ur help
What is the IPL and SPL?
If the wiki where up, I'd suggest looking at that, but as it is I'll explain it now...
What ROM where you attempting to upgrade to?
To get the device back, I would say "Read the wiki" but it's down!!!
Download this ROM.
In ActiveSync, disable "connect through USB" (File->Connection Settings).
Put the device into bootloader (the three coloured screen) and connect it to the computer using the USB cable.
Run the file you downloaded earlier. This should then install a new ROM.
From there, just wait for it to finish.
Now, it should work!
From there, you could re install the Orange WM5 ROM, or try upgrading to WM6. Make sure you read all the relevant guides first!
thanks alot i did as u said but it stops at 80% or 88%
then show this message (error 326 invalid command )
please help me
i'm feeling bad
my mail is [email protected]
What brand the device? Has it been SIM unlocked?
hi again brothers, pal zerocool. first u must unlock ur device to be able to accept any rom after that and solve pproblems.
first flash this rom its offecial and it solve dead prophet problems.
then make hard spl by program open file called hardspl.bat.
make hard reset.
flash ur rom u want.
make hard reset again.
then enjoy.
i uploaded the hardspl program but i couldnt upload the rom its so big so u can look in ur mail u will find the solution.
u can extract file by any program for zip.and tell me the news
dont forget to look to ur mail. see all of u later
Dead prophet
Hi guys,
I have been using a sh... Nokia sine I broke my prophet G4 in december by upgrading the OS.
I had downgraded first to NVID and then I tried to upgrade and it fails at 95%.
Sine this day, my prophet seem totally dead, no light when plug on both charger or computer, windows do not recognize at all the device because it is turned off. And it really do not seem to charge...
I am living in China now and a guy told me I had to change the PB board...The ost is 100Euros, but I am almost sure I an find another solution...
The weird thing is I cannot charge it at all ( I mean no lights but does it charge a little?).
The guy tested my prophet with another battery and in that ase, it is stuck on the bootloader.
We tried several roms and it always fails at 95% and the error is 200 something, maybe 245 or 243, I do not remember sorry...
Is my phone hardware is dead? or it is just a software problem and I did not see the right guy?
Do I need to buy a new battery? I have read that sometimes the device is not able to recognize it even if it the offiial one and even if it is working on another device...
PLease help me I don't want to loose this phone that I've been using for almost 3 years...
Otherwise I will switch to an iphone but I am not sure to be as happy than I was with my prophet.
Xie Xie for your advice and answers.
Guilh1
Can it enter bootloader at all?
If yes, what are the IPL and SPL?
If not, it will be a hardware problem (may just be connectors to the battery but may be something more).
the only way of recovery is using jtag
but 1st we must discover the location of jtag pins on motherboard
I just do not know because with my actual battery, anything is possible....
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
I may be right about the battery onnectors though, but the problems seem to be from the phone connectors or the battery it self???
Thank you anyway for your very quick reply
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
Click to expand...
Click to collapse
If it can enter bootloader, it is almost certainly your battery at fault!
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/B] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
Click to expand...
Click to collapse
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/b] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Click to expand...
Click to collapse
Please look at this if you want more help, post here...
thanks alot dear samuraititio
but i can't flash it
it writes (no vender id)
help me please i tried another tool with the same nbf file it stops at 80%
and it automatically enter the boot loader
and i can't do ant thing
its information
jamin/g4
ipl 2.13.0001
spl 1.01
i think my problem is in the spl coz it was 2.13.0001
and now it's 1.01
how can i fix it please i still starter in this way so i'm trying;
help soon please
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
l3v5y said:
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
Please look at this if you want more help, post here...
Click to expand...
Click to collapse
hello pal i3v5y
i have the same problem
idid what u said the flashing stops at 80%
i need ur help please
i'm online at the moment and u too help me soon if u can please
my e-mail is [email protected]
waiting for u i don't have any other device to use and i need it
l3v5y said:
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
Click to expand...
Click to collapse
now i flashed the official rom of jamin but it stopped at 80%

Categories

Resources