I have a cingular wizard with WM6 TNT 1933 (Build 18533.0.7.0) w/ TouchFlo. My battery recently died (thought it was bricked for a while, then tested the battery and bought a new one). My wizard won't connect to activesync through a usb cable(I have the advanced network checked OFF), and I don't have a bluetooth adaptor on this laptop. I have wifi here. First off I want a different OS because this one is too loaded and there isn't enough free memory, a bunch of apps I don't need. Also I'm wondering if a new OS will let me connect to activesync. Is there anyway to load one onto there, or am I just F'd?
is the phone operational now?
im sure that sktools had a repair activesync option then you can flash whatever
Bluetooth
You can use bluetooth to connect with activesync
invictus09 said:
I have a cingular wizard with WM6 TNT 1933 (Build 18533.0.7.0) w/ TouchFlo. My battery recently died (thought it was bricked for a while, then tested the battery and bought a new one). My wizard won't connect to activesync through a usb cable(I have the advanced network checked OFF), and I don't have a bluetooth adaptor on this laptop. I have wifi here. First off I want a different OS because this one is too loaded and there isn't enough free memory, a bunch of apps I don't need. Also I'm wondering if a new OS will let me connect to activesync. Is there anyway to load one onto there, or am I just F'd?
Click to expand...
Click to collapse
gmendezg said:
You can use bluetooth to connect with activesync
Click to expand...
Click to collapse
However ROM flashing must be done by direct USB connection, you didn't read the question carefully.
If you start RUU and plug the USB to your computer, the RUU screen on your wizard should display USB. If this is the case, you can run RUU directly.
If that doesn't work, try it on a different computer.
what about flashing a new rom via bootloader? have u tried that?
Htc fuze (raphael)
I know this is an old thread, but it came up when I searched this problem. I didn't find a lot of info easily, so I just tried a few things.
Problem: Cannot connect to ActiveSync because phone boots into Windows 6.5 beta and is locked at the screen saying the trial is over. When connecting it to the computer, the computer detected a device but ActiveSync could not connect.
Solution: Remove battery from phone and re-insert. Turn on while holding Volume Down button to get into serial mode. When you plug the phone into the computer in this mode, it should switch to USB mode. This allowed me to run RaphaelWrapper and then repeat the Volume Down boot once complete and reconnect to load the RUU for the AT&T stock OS.
If your phone does not switch from Serial Mode to USB Mode when connecting via USB, there is most likely a problem with the phone's USB port or a more serious problem than described above.
I hope this helps someone else! =)
Hi every body I have I-mate k-jam G3 wizard can I upgrade it to windows 6 ?
Thanks 4 all people will help me......
Related
So I recently downloaded the "RUU_Hermes_CINGULAR_WWE_2_1_[1].15.502.3_6275_1.40.30.00_108_Ship" ROM for my 8525, in hopes that it will provide me with a more stable pda/phone enviroment so that I may do the work I need to without having to hard reset every other day or so.
When I try to run the ROM install, I follow all the insturctions but when the update starts to run, it shuts my activesync connection off so the update can't run and throws back an error that it lost connection with the device.
Any Help Here? Thanks
PS: I love the idea of being able to use my 8525 for all my work and play needs, but if this update doesn't help make the device more stable, I will have to sell it for something that doesn't crash this much.
hey..iv got same problem.. i think it maybe cause we are using windows vista (thats the only information i can find about it).. i wanted to update ma rom aswell
I'm using XP Pro.
try running it on another system...if available...
anyone know the solution to this?!
OK, have you installed HardSPL ??
Check my SAFE WM5 upgrade guide, if you follow the procedures in there you should be fine.
Yeah, as far as stability goes most the wm5 roms out of the box aren't going to be the best. with any rom i use sktools to tune it up for performance/stability settings. It does this automatically so you don't have to find various registry keys. So don't think just because you are going to another rom everything will be okay.
Read the wiki, search the threads, you will find answers to all your problems.
As far as you not being able to connect what is your spl number? Also, have you tried hard reseting then connecting or trying another computer. I had the same problem when downgrading a black 2.5 with hard spl 2.1 ( i had to downgrade to send it back to cingular). I ended up just downgrading to the highest version of cingular rom which is branded AT&T. It looked like a pretty good rom but I did not play with it.
he does not need hardSPL(at least i dont think so) he is just runnning an update for another cingular ROM, its still the same CID...try running it on another system, i had this same problem and it worked on another system....
Malik05 said:
he does not need hardSPL(at least i dont think so) he is just runnning an update for another cingular ROM, its still the same CID...try running it on another system, i had this same problem and it worked on another system....
Click to expand...
Click to collapse
HardSPL will protect him against a faulty SPL flash if it occurs, a newer SPL is likely to be in the ROM update aswell as a newer radio possibly. Having the same CID doesnt matter because if the radio or SPL flashing procedure messes up it can create a bricked device VERY easily (corrupt SPL or even a corrupted CID/Radio BL). Besides if he already has HardSPL that would explain why the RUU doesnt reconnect when the device is in bootloader mode.
mrvanx said:
HardSPL will protect him against a faulty SPL flash if it occurs, a newer SPL is likely to be in the ROM update aswell as a newer radio possibly. Having the same CID doesnt matter because if the radio or SPL flashing procedure messes up it can create a bricked device VERY easily (corrupt SPL or even a corrupted CID/Radio BL). Besides if he already has HardSPL that would explain why the RUU doesnt reconnect when the device is in bootloader mode.
Click to expand...
Click to collapse
point well taken...=)
you mention, since he has already gotten HardSPL, why would that mean his device doesnt reconnect in bootloader?
put it in bootloader first and then run the update...
make sure you disable usb connections with active sync put your phone in bootloader and run the update might as well go with WM6 its a lot more stable than any WM5 rom i have played with .
OS crash
I run ROM install then computer shuts itself now my 8525 show hi true color with red/blue/white i tried to hard reset to solve but till hi true color what should i do?
trgrapsonu said:
I run ROM install then computer shuts itself now my 8525 show hi true color with red/blue/white i tried to hard reset to solve but till hi true color what should i do?
Click to expand...
Click to collapse
I've run there updates on my 8525. If the computer is shutting itself down, try another computer. This sounds odd. More of a computer problem then a Tytn Problem.
Malik05 said:
try running it on another system...if available...
Click to expand...
Click to collapse
=) have you even tried it?
I'm having a problem connecting ActiveSync over USB. When I first got the phone I was able to use that connection. Then I set up BT ActiveSync. I believe at the time I could use either USB or BT, but it has been a while. BT sync was so much more convenient for me that I haven't used my USB connection except for charging the phone.
Today I tried to get set up to upgrade the ROM, but ActiveSync doesn't seem to work over USB anymore. I turned off BT on the phone. When I plug it into my laptop's USB port the laptop makes a sound indicating it sees the connection. It makes a different sound when I unplug it. I also see the orange charge light come on on the phone. I usually charge the phone this way when I am on the road since I don't carry the wall charger with me.
I think at one point I installed a river that I fdound here to access the phone in bootloader moder. Other than veryfying the phone connected this way, I never did anything with the driver. IT has been so long that I don't remember the details. Could that be affecting the connection for ActiveSync?
I have made sure my firewall is inactive. In Windows XP Device Manager I see an HTC USB Sync device under Windows CE devices. Would it be safe to remove that device?
Any ideas how I can get USB ActiveSync to work again?
Is it totally crazy to try the ROM upgrade over the BT connection?
emuyshondt said:
I'm having a problem connecting ActiveSync over USB. When I first got the phone I was able to use that connection. Then I set up BT ActiveSync. I believe at the time I could use either USB or BT, but it has been a while. BT sync was so much more convenient for me that I haven't used my USB connection except for charging the phone.
Today I tried to get set up to upgrade the ROM, but ActiveSync doesn't seem to work over USB anymore. I turned off BT on the phone. When I plug it into my laptop's USB port the laptop makes a sound indicating it sees the connection. It makes a different sound when I unplug it. I also see the orange charge light come on on the phone. I usually charge the phone this way when I am on the road since I don't carry the wall charger with me.
I think at one point I installed a river that I fdound here to access the phone in bootloader moder. Other than veryfying the phone connected this way, I never did anything with the driver. IT has been so long that I don't remember the details. Could that be affecting the connection for ActiveSync?
I have made sure my firewall is inactive. In Windows XP Device Manager I see an HTC USB Sync device under Windows CE devices. Would it be safe to remove that device?
Any ideas how I can get USB ActiveSync to work again?
Is it totally crazy to try the ROM upgrade over the BT connection?
Click to expand...
Click to collapse
have you tried changing the setting on your phone "USB to PC"? I would try this first before digging to deep
slavetolustnyc said:
So I recently downloaded the "RUU_Hermes_CINGULAR_WWE_2_1_[1].15.502.3_6275_1.40.30.00_108_Ship" ROM for my 8525, in hopes that it will provide me with a more stable . . . When I try to run the ROM install, I follow all the insturctions but when the update starts to run, it shuts my activesync connection off so . . .
Click to expand...
Click to collapse
You may want to try using the Hard SPL v7 and then install your ROM. I did that and all went smooth as silk - six times now. I have been browsing ROMs to see which one suited my needs an personality, and it has been fun. You can find that on my FTP site at ftp://xda:[email protected]/xda_dlz/
This is a dynamic IP Address from a cable modem so two things are true
1. It is subject to change at any time.
2. It is not as fast as some of these speedy servers
But, I do know where it is.
shogunmark said:
have you tried changing the setting on your phone "USB to PC"? I would try this first before digging to deep
Click to expand...
Click to collapse
I had tried this yesterday and checked the Enable advanced network functionality box. Today I unchecked it and suddenly the PC saw a new USB device (HTC Sync USB, I think). It still wouldn't sync automatically so I manually executed /windows/repllog.exe. This time it connected.
Some observations:
- After the connection was established the the name of my 8525 was changed to something different (something like WM_ComputerName1, Where ComputerName is my computer's host name). I changed the name back and was able to re-invoke repllog.exe and sync with the old name.
- If I disconnect the USB cable from the phone and plug it in again ActiveSync doesn't connect until I manually run repllog.exe. It does work when I run the exe on the phone manually.
I went ahead and started the upgrade process after connecting by running repllog.
Executing the RUU file from the HTC site first put SPL 1.11 on the phone and left the phone in bootloader mode (with the tricolor screen). I left the phone with bootloader screen and followed the instructions (although by now ActiveSync had shut down so the part about the AS connection that the installer asked for was not true). The progress bars appeared on both the phone and the PC. It took a few minutes to complete, but the update was successful.
After the upgrade I was able to sync over USB without any problems. I am now syncing my contact from Lotus Notes and setting things up to my liking. Once I got over the USB connection problem everything worked fine!
Hi.
I am a bit embarrassed about writing this, I never thought I would make a brick of my Prophet during “upgrades”...
But here I am, with a phone that don't want to sync with any computer after I accidentally pressed cancel on an active sync dialog box asking for setup with a new device, during upgrade to the latest Touch VIII. Have upgraded several times with several different ROM’s before, but this time things went wrong.
If I choose to start my device normally, it goes trough the HTC screen and stops after the Qtek (HTC in Norway) screen listing the different versions of the hardware…
When I restart to boot loader (Cam button + reset) the 3 colours turn up ok, but when I put an USB cable in the device and the lower, left part of the screen shows USB, active sync will not recognise any new device no matter what I do.
I can still find the Prophet when I go to properties on the computer, but somehow active sync does not care about that.
Are there any way to use a program at the host computer to sync properly with the Prophet?
I would really appreciate any help that could rectify this problem.
Regards, Lars Norway
I believe the " WM6 Upgrade Guide" thread has the info you needed.
panda88 said:
I believe the " WM6 Upgrade Guide" thread has the info you needed.
Click to expand...
Click to collapse
Tried the info there without success...
The guide assumes that you have connection with ActiveSync, but I can not seem to get connection.
So, I really need some advice about how to make a connection to the computer I will make the programming from, when ActiveSync is not working properly.
Have tried to restart both the device and the host computer, have reinstalled ActiveSync, have tried to start the different roms without having a connection to A.S., but no luck...
Have realized my mistake and bought a new Prophet, but would still like to get the old one working again.
it has nothing to do with activesync.
Not sure u really understand the below statement from the thread I mentioned.
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
in case you can't NVID roms, you can still use those step1 roms mentioned by ROM gurus here.
panda88 said:
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
Click to expand...
Click to collapse
Well, the problem is that I am not able to connect...
As far as I understand, the only way to connect is by using ActiveSync?
Regards
connect = the cable between prophet and your pc. after that just run the rom update utility. just dun bother the activesync (does it sound logical to u to establish activesync in bootloader mode?)
OK, I have tried it, but will try on some different computers also.
Posting in a couple of hours.
Thanks for your help so far!
then wish u good luck. happy un-bricking.
OK, same as before.
Depending on which ROM I try, the following messages are the result:
Error [300]: Invalid update tool.
Error [274]: Connection (The update utillity cannot connect to your PDA phone.)
If I try the Touch VIII direct, it stops in Initializing for a while, and then a message appears with the text: Cannot connect to device, Would I like to try again?
Besides, in the welcome screen during the "ROMUpdateUtility_NV_G4.exe" in the Prophet_PV_Temp program, step nr. 2. asks me to ""Establish an ActiceSync connection with your PDA phone."
So, no change from yesterday yet...
are you using windows vistA???
Have only been using computer with XP Pro installed.
Anybody of the opinion that the connection tools built into Vista might do a better job?
hifiasylum said:
Have only been using computer with XP Pro installed.
Anybody of the opinion that the connection tools built into Vista might do a better job?
Click to expand...
Click to collapse
No, on the contrary. The best change you have is XP. Zeroed asked about Vista because it could be the reason of your troubles.
What I should do is just one detail different of what you have already tried:
Put the prophet in bootloader.
DISable "allow USB conection" in the conection-setting panel of ActiveSync
Connect your prophet with the USB cable
Run the NVID RUU again
If that is succesfull, you can upgrade to the WM6 ROM you like.
OK, will do.
Tried Vista just now, same errors and no luck.
Be posting in a minute...
OK, now I'm back.
Made a restart of the host computer, changed settings in ActiveSync, startet my device in Bootloader...
But unfortunately, no more success this time either.
Feel that the device must be more seriously defective/broken than others, this mishap happend at the end of the programming, when the 3 partitions were being written in the device. I was loading Touch VIII...
Anybody know if there is any more combination of buttons or reset methodes I could try?
Next step is to start opening the Prophet...
hifiasylum said:
OK, now I'm back.
Made a restart of the host computer, changed settings in ActiveSync, startet my device in Bootloader...
But unfortunately, no more success this time either.
Feel that the device must be more seriously defective/broken than others, this mishap happend at the end of the programming, when the 3 partitions were being written in the device. I was loading Touch VIII...
Anybody know if there is any more combination of buttons or reset methodes I could try?
Next step is to start opening the Prophet...
Click to expand...
Click to collapse
Sorry, I'm out of options...
OK.
Thanks again for all help and support.
Really appreciated!
Regards, Lars
hifiasylum said:
OK.
Thanks again for all help and support.
Really appreciated!
Regards, Lars
Click to expand...
Click to collapse
Just wondering if your computer detects prophet as a device at all? Does the normal plug device sound comes on when you plug in? Just a long shot, stick in a SD card and try with windows media player to see if it can sync or put files onto SD card. if so, get rom refreshed via SD card...
try few hard resets before you try this.
Not quite sure I understood what you suggested. I can get the device up in the host computers machine properties, but there is no way to get it up in any other program - like the Windows explorer.
Or are you saying that there is a way to boot the Prophet directly from a SD card? That would impress me!!!
hifiasylum said:
Not quite sure I understood what you suggested. I can get the device up in the host computers machine properties, but there is no way to get it up in any other program - like the Windows explorer.
Or are you saying that there is a way to boot the Prophet directly from a SD card? That would impress me!!!
Click to expand...
Click to collapse
This sounds dumb, but try restarting your PC, closing all apps running in background (including firewalls), restarting Prophet (with stylus in reset hole). DO NOT TRY TO USE ACTIVE SYNC. Boot into bootloader (Three colours screen), connect USB cable and flash QTEK lastest official, or Jesterz AKU 3.3 (I have found this ROM to have magical powers of unbricking.)
Good luck!
hifiasylum said:
OK.
Thanks again for all help and support.
Really appreciated!
Regards, Lars
Click to expand...
Click to collapse
Hmm this is wierd.I ran into problem earlier this month trying to flash a ROM but got stuck somewhere. So I followed the steps given in the sticky thread. Everything work smoothly. I am using XP SP2 and mine is a G3.
Let's make the assumption that your PDA is not faulty. Maybe you can try the steps again but this time :-
1. Change to another USB cable (or you may test the existing cable by connecting to a working pda)
2. Change to another USB port
3. Make sure you are not running any program that hogs the USB resource
4. If you are using USB hub, please don't connect using it. Make a direct connection to your computer.
that's all I can offer now...hope it helps.
Dear all,
I recently bought a HTC Touch Pro (MDA Vario 4) from T-Mobile.
Although the phone is nice, I do not like the interface T-Mobile has.
So, I decided to install a new ROM (Romeos beta 1.12 looks really nice).
I downloaded this ROM + Hard SPL 1.90, also I installed ActiveSync 4.5 (newest version for XP pro).
Hard SPL cannot find my phone when it is connected via USB, this is why:
When I connect my phone to my computer (via USB), the computer finds the phone (and adds a virtual harddrive) this is all working as intended. ActiveSync also detects the phone and tries to connect, it DOES connect but only as a guest...as such I cannot use Hard SPL, cannot install the new ROM, cannot sync Outlook contacts etc etc.
Being a guest on ActiveSync I can still look inside my phone (via added virtual harddrive) but that is it.
I am kinda new to a smartphone like interface, but it is damn frustrating this wont work.
When I google for help, all I see is that people (when they connect for the first time) get a activesync wizard who helps them make an account for it...I dont get that at all.
i reinstalled activesync several times, but with no success, I still get connected as guest instantly.
I would love to know how to resolve this.
if anyone got ideas? Please let me know.
With regards,
David
When you connect there are three settings that will show in your MDA Vario:
- connect to ActiveSync
- connect as hard drive
- connect as modem
Choose connect to active sync. If your MDA Vario is connecting directly in ActiveSync (and no wizard pops out) then it connected to it before. You could go to active sync and go to File->Mobile Device and verify if your MDA Vario exists in there. If yes, delete it then connect your MDA to start the wizard.
Hello,
Thanks for the reply.
I forgot to mention, that I always choose Activesync when connecting.
But my options in Activeync 4.5 are down to a minimum, I cannot recall being able to go to file->Mobile Device, will check tonight though.
Thx,
Regards,
pfcsabre said:
When you connect there are three settings that will show in your MDA Vario:
- connect to ActiveSync
- connect as hard drive
- connect as modem
Choose connect to active sync. If your MDA Vario is connecting directly in ActiveSync (and no wizard pops out) then it connected to it before. You could go to active sync and go to File->Mobile Device and verify if your MDA Vario exists in there. If yes, delete it then connect your MDA to start the wizard.
Click to expand...
Click to collapse
Manetho said:
So, I decided to install a new ROM (Romeos beta 1.12 looks really nice).
I downloaded this ROM + Hard SPL 1.90, also I installed ActiveSync 4.5 (newest version for XP pro).
Hard SPL cannot find my phone when it is connected via USB, this is why:
When I connect my phone to my computer (via USB), the computer finds the phone (and adds a virtual harddrive) this is all working as intended. ActiveSync also detects the phone and tries to connect, it DOES connect but only as a guest...as such I cannot use Hard SPL, cannot install the new ROM, cannot sync Outlook contacts etc etc.
Click to expand...
Click to collapse
You sure can flash the rom and spl even as a guest, i've done it several times and can confirm it working. Have you tried just executing RaphaelCustomRUU.exe?
Also, did you chose ActiveSync in the phone's usb connect popup?
there's also a way of flashing by booting the phone straight into bootloader mode and then executing the flasher. Dunno if it works for stock SPL though.
Couldn't hurt trying;
1. Remove the battery
2. Re-insert battery
3. press vol down and power button to turn the phone on
4. Connect usb and flash with RaphaelCustomRUU.exe like usual.
Hi,
I have had my 8125 for about 2 1/2 years now, love it!. Just the other day, it started locking up and giving me the white screen of death.
I tried to flash it with a rom, and it got to 99% and then lost connection. Tried to do the recovery, but that failed too.
I have found alot of good information from the smart and wonderful people on this forum and tried a bunch of stuff.. but I am now stuck.
Now, I can always boot into the bootloader, and it says USB over the left softkey, but no apps can connect to the phone.
I tried to use other RUU roms, HardSPL, SoftSPL, etc...I tried to unlock my CID using the thread in this forum, but SoftSPL couldnt connect to the phone via USB.
All apps error with "error unable to connect to device."
I have read the forum about having a bad mimi-USB port, but I dont think thats my case.
Please help! I am pretty close
Dell D620 CoreDuo 1.8Ghz; WinXP SP2
ActiveSync 4.5
IPL 2.25.0001
SPL 2.25.0001
end123 said:
Hi,
I have had my 8125 for about 2 1/2 years now, love it!. Just the other day, it started locking up and giving me the white screen of death.
I tried to flash it with a rom, and it got to 99% and then lost connection. Tried to do the recovery, but that failed too.
I have found alot of good information from the smart and wonderful people on this forum and tried a bunch of stuff.. but I am now stuck.
Now, I can always boot into the bootloader, and it says USB over the left softkey, but no apps can connect to the phone.
I tried to use other RUU roms, HardSPL, SoftSPL, etc...I tried to unlock my CID using the thread in this forum, but SoftSPL couldnt connect to the phone via USB.
All apps error with "error unable to connect to device."
I have read the forum about having a bad mimi-USB port, but I dont think thats my case.
Please help! I am pretty close
Dell D620 CoreDuo 1.8Ghz; WinXP SP2
ActiveSync 4.5
IPL 2.25.0001
SPL 2.25.0001
Click to expand...
Click to collapse
Ok,first,no other custom build rom will flash on it,except official stock rom of the carrieror,however, you can try wizard_love rom,as it has patched IPL/SPL (Bootloaders),so don't try to flash any other custom build,as its a G4,custom rom can only be flashed through SoftSPL or HardSPL.
Download official carrier's stock rom and wizard_love rom.
Secondly,
1.Disable activesync or rather uninstal it altogether,as its not needed during flashing a rom.
2.End process 'wcescomm.exe' in the 'windows Task Manager.
3.Clear and delete the 'Temp Folder' files
4.Run 'Disk Cleaner'
5.Disable all Anti Virus and Firewall.
6.Try to stop/disable all running programs in the background via 'Task Manager'
7. Get the battery fully charged,as many comm errors are due to weak or discharged battery.
After doing all this,get the phone in Bootloaders before connecting with pc via usb cable,there shudn't be any usb at the bottom of the Bootloaders,now connect with pc and check if usb appears at the bottom,if its there than,its establishing connection,go ahead and run official stock or wizard_love rom.Don't use the pc or play games or check emails,don't even do any word,excell or any office application.Check if any application/program interferes with the flash,either disable or remove that program.
Does the battery get charged through usb cable ? verify it.
If after getting the phone into bootloaders and connecting through usb cable,small usb doesn't appear,it means there's a connectivity problem,replace the usb cable and verify it again.Even try with another pc with winXP or change the usb input port of the pc ,put the usb cable in some other usb port on the pc.
Apart from all these,I don't find any reason for not getting the flash completed
Hi,
Thanks for the help.. I tried the wizzard_love rom, and then went to the NBD_v8.3 /w TouchFlo rom and thats awesome!
my biggest issue was not able to connect to the device although it looked like it should have.
on another thread someone said to leave the battery out for 5 mins. I did that and all of a sudden it started to connect consistantly.
After that I did the HardSPL and started flashing and all is well..
Thanks for your help!!!!
Hi everybody, I recently got myself a Mac I love it but there is one problem. No WinMo Device Center. So to work around this I decided to buy Paralells (for MS Office and WinZip as well)... Anyway, after setting up WindowsXP SP3 and ActiveSync in Windows, all seems well. Well when I connect My HD2 to my Mac via USB (select to connect to Windows) it installs proper drivers and I can use ActiveSync normally.
But here's my problem: When I try to flash, it goes to the bootloader, takes a while but installs the drivers to connect to USB in bootloader, and on my HD2 it even says "USB" but whenever I try to continue the CustomRUU past that point I get the connection error. So I restart, this time going to bootloader first, says it's connected to USB on my device again, but again I get the connection error.
I know you may be saying "Why not just flash via SD card?" and that's what I normally do but I haven't found a way to Task29 this way, and I always do Task29 before switching ROMs. So if anyone either has a solution or a workaround, please help a brotha out! Thnx