Related
I am running:
SPL-2.40.Olipro
3.35 radio
dcd 3.0.1 rom
I have the verizon xv6800.
I have lost connectivity between PC to phone via USB. Verizon is sending me a replacement.
Is there a way to get it back to stock using a micro SD card (bootloader, radio, rom)?
If not I plan on sending "as is" once I get me replacement--don't really want to do this.
Thanks in advance
hens4th said:
I am running:
SPL-2.40.Olipro
3.35 radio
dcd 3.0.1 rom
I have the verizon xv6800.
I have lost connectivity between PC to phone via USB. Verizon is sending me a replacement.
Is there a way to get it back to stock using a micro SD card (bootloader, radio, rom)?
If not I plan on sending "as is" once I get me replacement--don't really want to do this.
Thanks in advance
Click to expand...
Click to collapse
Have you simply lost connectivity to Activesync? Have you tried another PC? Do you not hear the 'add new hardware' chime when connecting your device? Can you boot into the OS? Can you not flash your phone via the SDcard method to another 2.40 bootloader using ROM? Have you failed in attempting the Wiki Downgrading instructions -- particularly using the Titan relocker?
hens4th said:
I am running:
SPL-2.40.Olipro
3.35 radio
dcd 3.0.1 rom
I have the verizon xv6800.
I have lost connectivity between PC to phone via USB. Verizon is sending me a replacement.
Is there a way to get it back to stock using a micro SD card (bootloader, radio, rom)?
If not I plan on sending "as is" once I get me replacement--don't really want to do this.
Thanks in advance
Click to expand...
Click to collapse
Here is the answer:
1. Format your MicroSD card to FAT32
2. Extract the .NBH you desire to flash (use winrar) from the exe or zip and put it on the microsd card, rename it from RUU_signed.nbh to TITAIMG.nbh
3. Put the MicroSD card in your phone reboot to the BOOTLOADER screen (camer+power+reset) it should then start updating with the .NBH on the SD card and the procedure should begin automatically.
-Sayajin
I think if he uses the sd card method above he will have problems. my understanding is that the stock rom will freak out with olipro 2.40. What he really needs to find out is if it is possible to relock without his USB port functioning. then the sd card method will work to flash a stock rom.
on a related question to the one asked by the OP, can a whole ROM be flashed using an SD card, including the radio? I think I read in the past that flashing radio firmware via SD was very difficult and troublesome...
Like maccaberry mentions, will the stock rom "freak out with olipro 2.40?" Is is possible to flash stock rom and relock from micro SD card?
I have tried several USB cables/PCs and it is just not activesync--troubleshooted with Verizon for 2 hours, the problem appears to be hardware related.
After creating this thread I did read up a bit on the wiki, and was going to try using instructions there, but the part about "the stock rom will freak out with olipro 2.40" has me a bit hesitant to flash stock. If I don't get a solution to update bootloader from micro SD, once I get my replacement and activate it I might try flashing to stock even with olipro 2.40--I am sending it back so if it does get messed up I just have to hope verizon does not come back knocking on my door.
hens4th said:
I have tried several USB cables/PCs and it is just not activesync--troubleshooted with Verizon for 2 hours, the problem appears to be hardware related.
Click to expand...
Click to collapse
You still haven't stated whether or not you hear a chime and/or see a change in the hardware devices list on your PC when your OS is loaded on your phone if you and you plug it into your PC.
hens4th said:
After creating this thread I did read up a bit on the wiki, and was going to try using instructions there, but the part about "the stock rom will freak out with olipro 2.40" has me a bit hesitant to flash stock.
Click to expand...
Click to collapse
Via the SDcard method, try to flash your device to another 2.40 bootloader using ROM. So that you don't need to be concerned over radio incompatbilities (if you do have the correct 3.35 radio installed for your DCD 3.0.1 ROM) you can try to reflash again with a build from DCD or a ROM with my kitchen. Or you can try one of the older OS/3.16 radio ROMs which also use 2.40. Each of the OS and radio ROMs can be flashed from the SDcard.
I'm sorry, but I wasn't clear in my first post that you do need an active USB connection to change the bootloader and that is why I asked if you could boot into the OS, heard your PC chiming on new hardware connected, or had attempted to reflash your phone to another ROM (or same ROM again) via the SDcard. Also, have you tried a hard reset on your phone?
The issue may be hardware but more than likely it is a software problem on your device or PC.
miguelfp1 said:
on a related question to the one asked by the OP, can a whole ROM be flashed using an SD card, including the radio?
Click to expand...
Click to collapse
Yes, any ROM portion should be able to be flashed via that method. On multiple times I have flashed a separate radio ROM without issue.
Keystone said:
You still haven't stated whether or not you hear a chime and/or see a change in the hardware devices list on your PC when your OS is loaded on your phone if you and you plug it into your PC. Via the SDcard method, try to flash your device to another 2.40 bootloader using ROM. So that you don't need to be concerned over radio incompatbilities (if you do have the correct 3.35 radio installed for your DCD 3.0.1 ROM) you can try to reflash again with a build from DCD or a ROM with my kitchen. Or you can try one of the older OS/3.16 radio ROMs which also use 2.40. Each of the OS and radio ROMs can be flashed from the SDcard.
I'm sorry, but I wasn't clear in my first post that you do need an active USB connection to change the bootloader and that is why I asked if you could boot into the OS, heard your PC chiming on new hardware connected, or had attempted to reflash your phone to another ROM (or same ROM again) via the SDcard. Also, have you tried a hard reset on your phone?
The issue may be hardware but more than likely it is a software problem on your device or PC.Yes, any ROM portion should be able to be flashed via that method. On multiple times I have flashed a separate radio ROM without issue.
Click to expand...
Click to collapse
Keystone thanks for you help...I did do the Device manager check...nothing. Several hard resets were done (memory card in/memory card out). I will try you suggestion about trying a different ROM (or same ROM again) that is made for 2.40. My radio is 3.35.04.
Is it a true statement that the Verizon stock rom/radio will NOT work with 2.40?--I could try this but like I said before I am a little nervous since I know I can't fail over to using USB to PC to help my situation.
You need to flash via the SD card as they say. Put whatever version ROM that goes along with your current radio version. Then once you get it up and running you should be able to connect via activesync and run Titan Relocker to get the 1.30 SPL loaded and 2.40 removed. Then you have a choice to leave it stuck there and return it like I done with one once, or you can flash the stock ROM and radio. There is a chance you can do that from the SD aswell incase your pc fails to pick it up again while in bootloader mode. You'll have to get someone elses input on if that part will work or not.
By the way, the stock ROM isn't your real worry. It's the 2.40 bootloader that will get everyones attention. So you really need to go ahead and properly flash and hope activesync will connect.
Is it a true statement that the Verizon stock rom/radio will NOT work with 2.40?--I could try this but like I said before I am a little nervous since I know I can't fail over to using USB to PC to help my situation.
Click to expand...
Click to collapse
You CANNOT flash a stock (verizon signed) rom with 2.40 period. You must relock the phone back to the stock bootloader, and only then can you flash the verizon signed roms.
Key,
You seem to be the expert with SD flashing. Maybe you know a mehtod he can use to get the bootloader on without USB. What I fear is that his USB hardware is fried. In that case, even a flash of a olipro 2.40 compatible rom is still leave him stuck where getting back to stock is concerned. I notice that the bootloader uses a similar software as the roms for loading onto the device. Is is possible to get a bootloader loaded via sd card. I have a feeling it is not possible because the olipro's all use a two step process.. 1st they load a soft (temporary) SPL and then 2nd they load the hard SPL. I have read elsewhere (by ImCoKeMan) that you should not try to run the unlocker via RUU so I assume SD flash version would also not work.
Hens,
If Key cant help us here you might want to pm ImCoKeMan over at ppcgeeks and ask him if the relocker can be loaded via SD card.
Do you have insurance? The device might have an accident with a drop from a 3 storey building that will erase the bootloader altogether..
Finally, you could donate the device to Madman34. He is looking for bricked phones for JTAG experimentation. http://forum.xda-developers.com/showthread.php?p=2019937#post2019937
I was looking into that before I posted my other reply. The one concerning thing about that is when I decompile the titanrelocker.exe file there was a relocker.nb and a 1.30 spl nbh file. I'm pretty sure both are needed, then again I could be way off base. The cool thing would be to get that relocker.exe to run on our mobile device. If that would work it would be easy to set up the SD card to autorun it once WM booted up.
Three story drop huh.... I was thinking Popcorn bout 10 seconds and
how long should this method take mine has been loading for 20min
OK I received a brand new xv6800 from Verizon today. Haven't even activated it yet. Wanted to update it first. So i downloaded Hard-SPL-MFG.exe and ran it. I get to the boot loader screen and it reads 2.40. Then the directions state disconnect cable and reconnect. I do that and the boot loader shows that it is connected via USB, however I cannot get a new activesync connection unless i restart. But when i restart lose the 2.40 bootloader. and the update errors out. I have tried the titan exitbl file but it cannot find the usb connection.
What am I missing?? Do I need to go the SD card route (dont have one yet)
My bootloader is 1.04
Any help would be appreciated
Don't worry about activesync after you replug it in. Just keep following the instructions. As long as when you plug it back in, it says USB at the bottom, just keep going.
Ok that sort of worked. Now im stuck at the 2.4 bootloader screen Fun stuff
You can run the fix from here.
The same fix is probably posted here too I just don't know where.
Thanks ran that again and it worked so I am back in business. Since you happen to be here any suggestion on which kitchen and radio to install
See this post. It worked for me.
Im working on radio and got it from your link but there is no link in the post to a kitchen i was going to downlod the latest one fromt eh lifesnotgood link which is called "dcd_titan_kitchen_3.2.2.rar" that should work right?
I have never used DCD. I use ppckitchen.org. You may want to consider just loading a custom ROM first unless you know how to install and use a Kitchen already. Sometimes it is easier to flash a prebuilt custom and get your phone working, then start cooking and flashing your own.
With the ppckitchen you don't have to do carrier cabs, you just select your carrier in the kitchen.
OK i really appreciate all the help and I know i sound like a total noob but went to ppckitchen and everything i see is a kitchen i dont see a full rom, what am i missing
They only have the kitchen to make a ROM. belive DCD has some custom ROMS.
Thanks for all your help all installed and running, now just need to activiate with verizon
'Have a li'l question about updating to Olipro myself...
I could've swore that b4 I'd upgraded to Sprint OEM ROM v3.56.651.0, I could update to Olipro v2.40 via SD. Now, however, I'd had to do so via USB. Am I mistaken? Can you not use the .nbh file in the .exe pkg? I like bein' free of HAVING to use a desktop to accomplish PPC tasks.
Thanks, Everyone.
Just download DCD's 3.2.2 ROM on the 1st page of his post. He has a kitchen AND a ROM.... http://forum.xda-developers.com/showthread.php?t=407376
As for using NueSPL 2.47, DO NOT use it until No2chem has finished his research on downgrading XV6800's.... While it has distinct advantages over olli 2.4, he's not sure about downgrading the bootloader to 1.X versions..... That is if you ever have to take your phone into verizon for service....
Before I start I did searches and looked at all the posts that apply to this situation and could not find anything. After spending many hours searching decided to try posting.
Situation:
I have a Verizon xv6800 that I am trying to update so I can have GPS. The first thing I did was to flash the OLIPRO 2.4 ROM. After the flash was complete everthing seemed OK but the power button no longer worked to turn the phone on. Also if you called the phone it would not ring.
The next thing I tried was to use an SD card to load nuespl 2.47. Again everything seemed OK but the power button still did not work.
Then I loaded OLIPRO 1.2 ROM and now everything seems work perfectly including the power button.
The boot screen verifies that the OLIPRO 1.2 is loaded.
Now I am confused as to which radio I should be using since the "Step by Step tutorial for unlocking your device and cooking your own ROM!!! " post said not to use OLIPRO 1.2.
Can any body tell me the next steps I should do to get an upgraded radio?
Please make it simple since obviously I can't figure it out myself.
Thanks for any assistance.
karter said:
Before I start I did searches and looked at all the posts that apply to this situation and could not find anything. After spending many hours searching decided to try posting.
Situation:
I have a Verizon xv6800 that I am trying to update so I can have GPS. The first thing I did was to flash the OLIPRO 2.4 ROM. After the flash was complete everthing seemed OK but the power button no longer worked to turn the phone on. Also if you called the phone it would not ring.
The next thing I tried was to use an SD card to load nuespl 2.47. Again everything seemed OK but the power button still did not work.
Then I loaded OLIPRO 1.2 ROM and now everything seems work perfectly including the power button.
The boot screen verifies that the OLIPRO 1.2 is loaded.
Now I am confused as to which radio I should be using since the "Step by Step tutorial for unlocking your device and cooking your own ROM!!! " post said not to use OLIPRO 1.2.
Can any body tell me the next steps I should do to get an upgraded radio?
Please make it simple since obviously I can't figure it out myself.
Thanks for any assistance.
Click to expand...
Click to collapse
Ok no worries about the newbie thing. We all were newbies at one time!
First it sounds like the 2.40 flash did not completely go well. So since you are back to 1.20 I would upgrade in this order:
1) First update your radio to 3.42.50. This is the latest radio and seems to help with phone service issues. At least that is what I have seen. You will need the RUU install files so I attaching RUU.zip for this. Unzip this and then when you download the upgraded radio drop that file into this directory and then flash. If successful your phone should display 3.42.50 at boot time.
2) Next upgrade to 2.40 of the unlocker. I am attaching the install I use, so unzip the file and then run it to install/upgrade your phone. If successful your phone should show 2.40 when done.
3) Now you are ready to persue a ROM or kitchen that is GPS capable. There are many of them. I am currently using DCD's 3.26 kitchen but No2Chem also has a 5067 kitchen that is very stable. If you have questions about this process do not hesitate to email me at [email protected].
Steve
I did step one and everything seemed OK. Took several minutes with progress bar and exited normally. The boot screen indicates 3.42.50 as per instructions. But now the phone gets stuck at the white verizon screen. Should I proceed to step 2?
Thanks
Ken
karter said:
I did step one and everything seemed OK. Took several minutes with progress bar and exited normally. The boot screen indicates 3.42.50 as per instructions. But now the phone gets stuck at the white verizon screen. Should I proceed to step 2?
Thanks
Ken
Click to expand...
Click to collapse
Take the battery out and then put it back in. It should boot then. Go to step 2 then.
Steve
Took battery out waited 1 minute and replaced battery. Still stuck at white screen.
Ken
karter said:
Took battery out waited 1 minute and replaced battery. Still stuck at white screen.
Ken
Click to expand...
Click to collapse
Move on to step 2. Quick question...is the current ROM the stock VZW ROM or one from XDA?
Steve
Actually he gave you the instructions backwards. (Tho his method may work, it's just not what the Wiki says to do) You always update the bootloader first, then the radio, then the rom. The new radio requires a new bootloader (hence why it's locking up), go ahead and reinstall BL2.4, if that doesn't work, see if you can find an older non-gps radio, and flash it via the SD card. Once you get back to either an old bootloader and old radio, or a new bootloader and a new radio, then you will have better success getting the rom flashed.
You were fine actually with your original 2.40 install, it will boot once normally, however as soon as it goes to sleep or you turn it off it won't turn back on, a soft reset will get it back up, but it will keep crashing. So at that point you can flash the radio and ROM from the Bootloader screen.
If you can get 2.40 (actually get 2.47 if you can, worse case use 2.40 and upgrade the radio and rom to the new version, then run 2.47 from the pocketpc and it will update you to 2.47 (I just did this yesterday).
So reflash to 2.40 if you can, otherwise do some searching for an old radio (non-gps) and flash it.
Then go back and re-read the wiki, it tells you that you have to flash the bootloader, then the radio, then the rom. It's always in that order for a first time flash. Once thats all done, any future updates should only require a single flash (for radio or rom).
BTC
BillThyCat said:
Actually he gave you the instructions backwards. (Tho his method may work, it's just not what the Wiki says to do) You always update the bootloader first, then the radio, then the rom. The new radio requires a new bootloader (hence why it's locking up), go ahead and reinstall BL2.4, if that doesn't work, see if you can find an older non-gps radio, and flash it via the SD card. Once you get back to either an old bootloader and old radio, or a new bootloader and a new radio, then you will have better success getting the rom flashed.
You were fine actually with your original 2.40 install, it will boot once normally, however as soon as it goes to sleep or you turn it off it won't turn back on, a soft reset will get it back up, but it will keep crashing. So at that point you can flash the radio and ROM from the Bootloader screen.
If you can get 2.40 (actually get 2.47 if you can, worse case use 2.40 and upgrade the radio and rom to the new version, then run 2.47 from the pocketpc and it will update you to 2.47 (I just did this yesterday).
So reflash to 2.40 if you can, otherwise do some searching for an old radio (non-gps) and flash it.
Then go back and re-read the wiki, it tells you that you have to flash the bootloader, then the radio, then the rom. It's always in that order for a first time flash. Once thats all done, any future updates should only require a single flash (for radio or rom).
BTC
Click to expand...
Click to collapse
The issue with reversing steps 1 and 2 is that the Olipro 2.40 does not allow the ability to update the radio ROM. You have to back down to 1.20 and then do the radio. That has been the case for the last two radios I have upgraded to. So that is why I put it in the order I did.
Steve
Ah ok, well, I had 2.40 installed for over a month and have updated my radio 3 times (tho I did it via SD card), I assume you meant it doesn't work via USB (and I remember now seeing posts that talked about that)
I stand corrected. His way should work. Just the phone will not boot properly until all 3 items are updated to GPS compatible files, BL 2.40+ Radio 3.42+, Rom 3.x. Prior to all 3 being updated tho, you should be able to flash from the bootloader, so boot into it and flash from there until all 3 are updated.
Once all 3 are flashed, your phone should work normally.
BTC
BillThyCat said:
Ah ok, well, I had 2.40 installed for over a month and have updated my radio 3 times (tho I did it via SD card), I assume you meant it doesn't work via USB (and I remember now seeing posts that talked about that)
I stand corrected. His way should work. Just the phone will not boot properly until all 3 items are updated to GPS compatible files, BL 2.40+ Radio 3.42+, Rom 3.x. Prior to all 3 being updated tho, you should be able to flash from the bootloader, so boot into it and flash from there until all 3 are updated.
Once all 3 are flashed, your phone should work normally.
BTC
Click to expand...
Click to collapse
Yes via USB since SDHC cards are not supported and I do not have a regular SD card. I really should buy one...they are cheap now.
Steve
I reloaded the original radio using a sd card and now the phone works again. Can I load OLIPRO 2.40 using a SD card? If so how.
Thanks
Ken
Not that I am aware of (tho I don't know everything....), I flashed 2.4 from my PC via activesync, let it reboot, and then had to run out and get a flash card and flash card reader (in order to format it correctly) then was able to flash the radio, and then flashed the rom via Activesync. (I just remembered that I had to flash my radio from SD card, I had completely forgotten until I stopped to remember why I bought the memory card reader)
If you have it working with your old rom, then I would copy 2.47 BL over to your phone in windows and run it, it will flash the bootloader for you (tho it requires a preformatted SD card (not SDHC)). It will offer to format it for you if you can't get it formatted correctly yourself. If it's already in the right format, it doesn't have to be empty as it will just copy the file, reboot, and delete the file automatically. If it's not in the right format and you have stuff on it already, copy it off to your harddrive, then put it back in and it will format it for you. Once it's formatted correctly, it will still work normally in the phone and on your PC, so it's worth it to get the SD card into the right format.
Once 2.47 is installed, boot into BL mode (camera, power and reset button), and then do the rest of the flashing over USB. It will auto-reboot after each flash, so keep going back into BL mode until after you get the rom flashed. Then let it boot normally, LET IT RUN CUSTOMIZATION (pending you are installing DCD's rom) If you are installing another carrier's rom, then never let customization run (unless it's your carrier). Once customization is done running, install your carrier's cab file, this is pretty important or the phone won't properly work, I would do one more soft reset and at that point your phone is all ready to go and you can set it up, and install your programs.
BTC
Billy the Cat
I wish I had known that the power button wouldn't work untill all three steps were complete. Because of that I got concerned that I may have screwed up the phone and started trying all sorts of things to fix it (probably making it worse in the process).
Now that I know how to get back to the original ROM & Radio if something happens I will try again to get the GPS working.
Thanks Billy the Cat and stevefxp
Ken
No problem. I was like you the first time I started to flash my phone, I had just gotten the BL installed and then had to leave, my phone wouldn't stay running so my wife got extremely mad at me because she would call and since the phone wouldn't turn on it would go to VM. It took me a while to get her to appreciate my phone again, til then it was "A huge waste of money" in her opinion.
Since then tho, I have shown her the great features of being able to search for an item on ebay when we are at an auction to get an idea of a item's value before bidding, been able to take pictures and email them to her at no cost (old phone was $.25 per message), and having the GPS makes it much easier to find some of these remote auction locations we go to.
So after all that, shes not screaming at me for buying the phone anymore, tho she still isn't happy I spent the money. Oh well, she fritters more money away than I do, so I don't have a problem buying something that will last me for 2 years with the amount that shes frittered away in a week many times.
BTC
I am still having the same problem with the white Verizon screen. These are the steps I took.
1. Reloaded the original radio 1.30.60 using the SD card approach
phone worked
2. Reloaded the original ROM 1.6.7
phone worked
3. Loaded nueSPL-2.47 using the sd card
Red/Blue/Green screen had:
TITA100
SPL-2.47No2Chem TITAN SPL EVT
CPLD - 9
4. Loaded radio 3.42.50 using the SD card
Verizon white screen has
M 09 P DCAAXOM - 4350
H3B60775B R 3.42.50
D 2.17
The phone now still hangs at the white Verizon screen. I really thought I knew the process but clearly I still do not understand something.
Any help??
every thing is ok, load a gps compatible phone rom like dcd 3.2.6 using the cd card method and it will work after that
I have the 3.2.6 kitchen downloaded from DCD1182 but I can't find the nbh file unless it is the RUU_signed.nbh file and I just have to rename it to TITAIMG.nbh
If that's not it where can I download the 3.2.6 nbh file.
Thanks
Ken
karter said:
I have the 3.2.6 kitchen downloaded from DCD1182 but I can't find the nbh file unless it is the RUU_signed.nbh file and I just have to rename it to TITAIMG.nbh
If that's not it where can I download the 3.2.6 nbh file.
Thanks
Ken
Click to expand...
Click to collapse
That is it.....
You guys are great. The phone is working again and has radio 3.42.50 and ROM 3.2.6 on the white screen so I guess everthing is correct now.
I also loaded the Verizon CAB to get internet and reprogrammed the phone with *228
I have one last question. What happened to the battery indicator in the upper right hand corner?
I really appreciate all the help you guys gave me. I read all the instructions but knowing nothing about what I was doing there is some information that would have been very helpfull if I had only known.
1. If you get in troubble you can reload the original radio and ROM to get the phone working again.
2. You really need to complete all the steps before you can expect the phone to work properly. I kept trying to test the phone at each step to make sure that it still worked. This approach got me in all kinds of trouble.
3. Don't panic if something doesn't seen right just ask the experts on this board. They have a wealth of knowledge on how to get out of trouble.
4. Make sure you have a micro SD card on hand before you start.
5. While it didn't answer all my questions read the WIKI flashing documentation completely before you start.
Again - thank you everyone for helping me to get my phone upgraded.
Ken
you can get the battery by changing the registry.
hklm/software/microsoft/shell/showtitlebarclock.
not sure what all the setting do. mine is set to 0 and i have the battery icon.
alternatively you can use htc home customizer to change the value for you.
All,
I downloaded the original Cingular/ATT Rom, just in case, and bought Sprite and backed up my settings. I downloaded SDA_ApplicationUnlock.exe and ran it (from my PC, is this correct?). SDA_ApplicationUnlock.exe seemed to run okay, and gave me the message "SDA Successfully unlocked, Please Reboot SDA Now!". I rebooted my phone and did not notice a change (I assume I should?) I ran the Rom update for WM6.1 Standard, which opened up a DOS-looking box that stayed there forever and did not indicate it was doing anything. After just over an hour I disconnected my phone and rebooted it, no change.
My questions:
1) Do I run SDA_ApplicationUnlock.exe from my PC or from the WM phone itself?
2) Any suggestions as to what I may be doing wrong?
3) What does CID Unlock do, and do I need it?
Just to review, I have a Cingular 3125 with WM5, and I want to go to WM6.1 Standard.
Please help! Thanks!
Frank
geekzilla65
You were supposed to run Jump SPL on your phone which puts it into a special bootloader then run the update utility should run correctly. I personally prefer the MicroSD flash method myself.
Jump SPL?
icecube57 said:
You were supposed to run Jump SPL on your phone which puts it into a special bootloader then run the update utility should run correctly. I personally prefer the MicroSD flash method myself.
Click to expand...
Click to collapse
Thanks icecube57!
I know that SPL files were copied to my phone automatically when I ran Rom updater, but I don't think it ever launched. I am really confused about the CID unlock. I read one post where it says I have to do this, and another that says for Cingular Roms you don't need to.
Also, you mention the MicroSD flash method - is there a post here that explains how to do that? I would not mind trying it if you think it works better. Please help!
Frank
geekzilla65
If i dont say it someone else will. Please use the search function.
If the utility didnt automatically launch the Jump Spl program then navigate to the root of your phone using file explorer start it manually from your phone and it will put the phone into bootloader then try running the utility again. Thats how i had to do it with my phone
Thanks
icecube57 said:
If i dont say it someone else will. Please use the search function.
If the utility didnt automatically launch the Jump Spl program then navigate to the root of your phone using file explorer start it manually from your phone and it will put the phone into bootloader then try running the utility again. Thats how i had to do it with my phone
Click to expand...
Click to collapse
Okay, that's fair, thanks. Can I get an answer on one more thing? I did look in the forums, in the Wiki ,etc. on this - I am still confused on what CID unlock is. I really don't want to brick my phone. When this worked for you, was this on a Cingular 3125? Did you have to CID unlock?
Frank
geekzilla65
What you are talking about permenantly CID unlocks the phone which allows you to flash any rom. Instead of being stuck with carrier specific roms. What the JUMP SPL does is loads a specially modified bootloader that temporarily fakes the Update Utility into thinking your phone is CID unlocked that way you can flash any rom without going through that long complicated process in making it permenantly CID unlocked. I have a 3125 myself and flashes all the roms in this forum fine with the Jumps SPL Bootloader method.
MicroSD Flashing
Im feeling nice. Here is the MicroSD Flashing Method
http://forum.xda-developers.com/showthread.php?t=311232
Thanks!
icecube57 said:
What you are talking about permenantly CID unlocks the phone which allows you to flash any rom. Instead of being stuck with carrier specific roms. What the JUMP SPL does is loads a specially modified bootloader that temporarily fakes the Update Utility into thinking your phone is CID unlocked that way you can flash any rom without going through that long complicated process in making it permenantly CID unlocked. I have a 3125 myself and flashes all the roms in this forum fine with the Jumps SPL Bootloader method.
Click to expand...
Click to collapse
Thanks icecube57!!! I really appreciate the answers! You rock!
Frank
geekzilla65
Thanks!
icecube57 said:
Im feeling nice. Here is the MicroSD Flashing Method
http://forum.xda-developers.com/showthread.php?t=311232
Click to expand...
Click to collapse
Thanks for this one too! Awesome!
Frank
geekzilla65
So
My problem is i cant use RUU because it gaves me Device ID Fail error. i have downgraded my G2 Touch from 2.73.116.61 (special hungarian t-mobile rom ) to 2.73.405.5 with Goldcard & RUU. Then, i've put a rooted rom(2.73.405.38), and the newest radio rom (*.09.26) with Cyanogen's recovery image. I'd like to know how could i put back the 2.73.405.5 rom with RUU, or any other rom with RUU, to make it stock HTC Hero? My T-Mobile havent came out with any update for the phone, so i cant try out that RUU
My point is when the Android 2.1 will come out for HTC Hero, then i'd like to upgrade too. Thanks for help!
btw: i've been searching for solutions for lot of days, so dont say "use google" if u cant give me specific solution, thanks
Alrighty,
If it was me, I would use the goldcard to RUU back to the earliest ROM possible (1.73). Then install a custom recovery like AmonRA, and use an update.zip to give you the stock Hero rom. (once you downgrade the ROM to 1.73, you can use fastboot to load the recovery image, so you don't even have to flash the recovery. This is as close to stock as you'll get.)
For the update.zip file for the stock hero, see http://android.modaco.com/content/htc-hero-hero-modaco-com/291942/gsm-24-11-hero-roms-radios-in-update-zip-format/. The one you are after is the second one down under 'shipping ROMs'
An alternative way to do this is to use the goldcard to install the exe (RUU) for the version you want. It's up to you.
So in short, use the goldcard again to RUU to what you want.
Goldcard is in the phone all the time, im using the stock memory card. If i do the goldcard it will be goldcard forever, atleast others said that. I've tried formatting the card, no luck
people have said that gold card method wont work on stock memory card so you have to go buy like a 4gb or 8gb card then put gold card on there and it should work fine.
I have stock memory card, and successfully made the goldcard, and downgraded my g2 touch, as the topic's name states it. i checked my goldcard stock memorycard with HxD, with i previously made my goldcard, and realised the first 17 line is zero, as the stock values were i think. i checked if i put the goldcard values back there, its different, so, is it possible the RUU made the goldcard stock? When the new android 2.1 ruu come out for hero i'll make the memorycard goldcard again, and check if its workin.
IIRC, it should NOT all be zeroes for the first 17 lines. I would make the goldcard again (you could even do it now so you have it working and ready for use). It shouldn't take too long since you've done it before, and will possibly have the tools needed downloaded to your PC already.
HTH
solved
at last i've done the goldcard procedure again, and it stood the same, i put the newest rom, working like a charm