Related
The Problem Is...
Every time i restart my phone via any type of reset....
(soft reset, hard reset, battery out of the phone, powerbutton turn off, a programs phone restart)
... the phone turns straight to the bootloader screen. It does not do the normal viberate and restart.
To get the phone to restart I have to go through a long process of removing the battery, plugging it into the charger, pressing all the buttons with a million resets.
Then eventually it will start up like normal.
Titan_exitbl.exe does not do anything... It sends the code and goes straight back to bootloader screen with any of the bootloaders stock or olipro customs
What I Have Tried:
installing and reinstalling the 3.39, 3.35, 1.30 stock radio
installing and reinstalling correct combinations of roms for the above radios. (including stock)
installing all bootloaders (including relocking)
each with their corresponding roms and radios
What I Think
Because of not being able to hard reset something is wrong there.
i'm open to suggestions
Where exactly are you right now?
What bootloader, ROM, and radio do you have installed? Are you able to boot into Windows Mobile?
right now completely stock i'm in windows mobile
i have now done a hard reset via settings->system-> clear storage
EDIT more exactly
verizon rom 2.09
radio 1.30.60
bootloader 1.06
Ok...do you have a microsd card to flash with?
not right now however,
let me know what you're thinking i might go grab one.!
I've got the same thing happening to me... I was running the test "sprint" radio on my alltel 6800 along with no2chem's latest rom... it started happening, so I decided to install the newest stock alltel rom... didn't fix it at all. What sucks now is I can't even get activesync working witht eh alltel rom now...
Also, I can get it to boot if I do one thing. If I connect up a usb cord (to a computer, or my usb headphone adapter) and hit soft reset, it'll boot fine.
However, soon as I hit that soft reset button on the bottom again, back to bootloader it goes.
This happened to me once before a long time ago, I fixed it by relocking the device and installing a stock Alltel rom... however I've read that's a bad idea with the newer GPS enabled roms and can kill the phone.
any ideas?
Just a quick update... after messing around I had an idea... I connected the USB headphones so I could actually do a soft reset that works... But this time, instead I held down the power/cam when I did it so it would load the boot loader... my thinking was that it might trick it into not loading it. Sure enough, it worked. Now when I hit soft reset, it does just that. No more boot loader unless I hold down those buttons.
Very strange... like the phone got tricked into thinking the buttons were always pressed down on restart.
Anyways, hopefully this will help others that might come across this issue.
spoke too soon... now its is doing it again after flashing the sprint rom back on and then no2chem's latest.
argh...
First off, I've been flashing my phone for almost a year now. So I don't consider myself too big of a noob. I loaded scrosler's round 4 rom. Worked great! Until I did a soft reset. It put the phone in bootloader mode and I can't boot up at all.
Here's what I have:
Olipro SPL 2.40
Radio 3.42.50
Here's what I've tried to get it out of bootloader:
mtty1.42.exe
titan_exitbl.exe
No success. I'm able to install a ROM, but as soon as it reboots after 100%, it goes right back into bootloader.
Someone please tell me it's not bricked
Try reflashing your radio.
BTC
kill the active sync processes via the task manager, then put the phone back into the usb cradle, run the titan exit bootloader and it should work.
josh77b said:
First off, I've been flashing my phone for almost a year now. So I don't consider myself too big of a noob. I loaded scrosler's round 4 rom. Worked great! Until I did a soft reset. It put the phone in bootloader mode and I can't boot up at all.
Here's what I have:
Olipro SPL 2.40
Radio 3.42.50
Here's what I've tried to get it out of bootloader:
mtty1.42.exe
titan_exitbl.exe
No success. I'm able to install a ROM, but as soon as it reboots after 100%, it goes right back into bootloader.
Someone please tell me it's not bricked
Click to expand...
Click to collapse
If no other suggestion works this will... But it sucks.... Flash a stock rom. I garuntee that will fix the problem. then just flash back. You don't have to flash a VZW ROM and I recommend against it. My new recommended ROM for unlocking and flashing is the Alltel ROM. Its got the latest radio in it (which you already have). Good luck and let us know how it turns out.
thanks for all the suggestions. i'm not sure what exactly went wrong, but i spent about a day and a half just to get it working again. it's somewhat stable now.
after flashing an older dcd rom, i was somehow able to get the OS to boot up, even after the auto soft reset. immediately i wanted to upgrade the bootloader to 2.47 since i've only found it in an exe(only can run from windows mobile) version. I then was able to flash the OEM MR1. Which automatically downgraded my radio. it was definitely the most stable thing i've flashed since the phone got all screwed up. i could soft reset as much as i wanted and didn't get the blue screen of death aka bootloader.
but of course, i couldn't be satisfied with no gps and no internet sharing. i use internet sharing more since i use it when i commute to work on BART (bay area's version of the subway) 50 min each way.
so now i'm on DCD's 3.2.6 ROM with 3.42.50 radio. so far it's somewhat stable. if i soft reset, i get the bootloader sometimes. but a couple solutions to the get the OS to boot back up is
1.) take the battery out for 20-30 seconds and power up
or
2.) take the battery out, plug in the computer usb or power usb with the battery still out. somehow resets the phone? i have no idea.
but i read somewhere that ROM's were causing people to have to take their battery out for 30 seconds to boot up. I doubt it was DCD's ROM's. But who knows, maybe i ran a bad radio file, ROM, or bootloader upgrade, that really caused the initial issues.
My only issue now other than getting the bootloader once in a while is that GPS isn't working. Not that big of a deal for now since I have the Pioneer AVIC F90BT in my car now. but would be nice to have it on my phone (tomtom & google maps) for that one time that might come up when i really need it and i'm not in my car.
again thanks for your help in trying to help a brotha out.
Verizon xv6800 bootloader and startup issues
My issues are, I cant get into the bootloader screen no matter what I try(power, camera and reset). Most times my phone will only go to the verizon screen and then just go white, other times, it may show the WM 6.5 startup screen and the freeze there. This all came from me trying to install WM 6,5 Beta 5 21159 rom from WM 6.1. On another not, my pc will not see my phone. So am I completely screwed? Is there any hope? Thanks in advance for any help.
So, overall, am I screwed?
Anybody have any suggestions?
Thanks
Can anyone help? my phone will not let me into bootloader mode or even startup past the verizon splash screen. I am desperately hoping that its not bricked. Also, the pc to phone usb connection will not see eachother.
My phone will charge via the usb cable to pc. When the wifi switch is turned on, the led on opposite side of the power led will do it green blinking.
Is there anyone that has time and is willing to work with me?
Thanks in advanced.
I have taken the phone apart so that I could push the internal buttons (power, camera and reset) to see if the outer shell buttons were the problem. They werent. I also still can't get past the verizon splash screen. Anyone have any ideas?
Thanks
I you cant get into bootloader you dont have any options.
For those of you who also read PPC Geeks, this is the same problem. I am just trying to cover more area and hopefully stumble across somebody that has a solution to my problem.
The current situation is that the phone will not boot at all. I can hard reset it, I can enter into the bootloader (which is no2Chem 2.47) and I can flash ROMs to it. However, when I try to boot the phone, the black HTC logo flashes for about half a second and then I get a black screen.
I have tried flashing the Sprint ROM available on HTC's website (RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_TITAN_3.42.02_ SPCS2.04_PPST_0718_Ship.exe) and this one: RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4 350H_SPCS_AM_Ship.exe.
I've hard resetted, soft resetted, taken the battery etc. Anybody have any idea what I should do or why this is happening? Thanks for the help!
Try some things here.
Follow section B. Usb Downgrade, I believe..
http://wiki.xda-developers.com/index.php?pagename=TitanStockHome
let me know if I helped ya out.
Ryan
I wasn't able to do any of that since I cannot create an Activesync connection between my phone and pc.
I think you may have messed up your bootloader, try and get another one installed on it. I recommed olipro 2.40 and radio 3.35 but you can use a higher radio. Dude you dont need an active sync connection, read the wiki article further. At most you would need the WMmodem drivers installed on your computer. Just put the phone in bootloader (power, camera, reset) and run the tools on the wiki site i linked to you. You can run RUU Rom Update Utility from your Home computer while phone is in bootloader mode, you do not need to have the phone fully booted into windows mobile and synced, or even connected to active sync. Hope this helps I could be wrong though, just try some things and read.
I tried running the TITAN_RELOCKER.EXE, but it wouldn't do it since it didn't have an ActiveSync connection. I have tried the RUU with multiple NBH files. Trying to flash the radio, rom, and/or spl. I will try the bootloader stuff again. Thanks.
EDIT:
Found a new symptom. When I don't have the power cable in I can use the power button to turn on the device and the top right light is green. When I plug it in the light flashes red and won't let me use the power button to turn it on, but will do the same "flash the HTC boot screen" if I soft reset.
Try renaming the .nbh file to TITAIMG.nbh and put it in a 1GB or less microsd card and then press the power button + the camera Button together and hold, and then press the reset button that is located next to your usb charging/syncing slot
good luck
I will give that a try. Does anyone have the nueSpl NBH or any other bootloader for that matter? I can only find the exe to run on the phone and I can't do that.
Hmm it says flash a boot screen? Sounds like you may need to do just that. I have never heard of the blinking red light other than low battery. You can try using PPC Geeks kitchen to build your own rom (temporarily) and you can choose which bootscreens you want to use. If you get the bootscreens to succesfully flash you can either test the ROM and see if you like it or flash the ROM of your choice and it will not overwrite your bootscreens, some overwrite the windows 6.1 screen but most of them do not.
PPCGeeks.com How to unlock device and cook your own rom
Read through that thread and download the PPC Kitchen, now dont open the kitchen run the kitchen updater, pick titan files, and the newest build 20931 and get started after that.
Dont pick an animation just splash, sub splash, and the Windows 6.1 splash. Now run it let it do its thing just make sure you are in bootloader before plugging in to computer. If the flash still doesnt work then you can try the MicroSD card method. Format the card to FAT32 and make sure its totally empty(not even a folder). Now navigate on your computer to mydocuments/buildOS RUU, then look for the RUU_Signed.nbh and copy and paste it to the Memory card and Rename to TITAIMG.nbh now put the card in your phone and then into bootloader mode(power camera reset same time) and let it try flashing. If you still cant get it to work and you have tried starting from scratch then the phone may be a brick. Hard to tell now try some more things.
Ryan
Hey all, I am having trouble booting anything onto my HD2 everytime i boot the phone i get stuck on the (tri colour screen) "Hardspl" i think..
I am able to install original HTC roms and custom roms via USB and Serial but after i install them and it says installation complete when the phone restarts it just gets stuck on the "Hardspl" screen again??
Any help is appreciated thanks
Here are some images to help
http://img29.imageshack.us/g/dsc0007riq.jpg/
(UPDATED)
How do i remove hspl ive tried installing an offical rom from the SD card but i still boot into this screen ????
Try this........
Power off the phone (make sure your battery is over 50%)
Turn on while holding the vol. down button.
You should be at bootloader (three colour screen)
If you have HSPL installed you should see "cotulla" and "HSPL" on the bootloader somewhere.
If youve been flashing official roms though this may have uninstalled HSPL.
I couldnt get the screenshots you linked to...
You can attach image files using the "manage attachments" button down under the text entry area.. (i think)
Id suggest trying to flash a stock/official rom just now until you get up and running.
With the phone at bootloader you should see the word "serial" at the bottom of the screen....
Connect via USB and wait for "serial" to change to "USB", this could take a few minutes.......
When you see "usb" flash the ROM from your pc......
You should make sure that you have the correct ROM for your phone, go to the HTC site and pump in your serial number.
If you still have problems after this then post back here with any error messages you might get...
Hope that helps.....
Thanks for the reply, for the link you need to add (http ://) sorry i should have mentioned that
but i just finished doing what you told be and it finished installing. it had the HTC logo on phone with loading bar as on PC screen no errors :S but im still stuck on the tri colour screen
I originally had android booted onto this mobile but the 3G was not working so i tried installing the HTC wm 6.5 rom that I downloaded from the HTC website but it would not get out of the tri colour screen after i installed it.
So i though it may have been the hardspl its self so i updated the SLP from 2.05 to the 3.03 one im currently on but it does the same thing
Hmm ok...
So the flash finished all the wasy to 100% and there were no error messages..
then the phone rebooted and went to bootloader (3 colours)...??
Restarting the phone just keeps returning you to bootloader??
Try turning off then back on while holding down both volume buttons and see what happens.
Which model of HD2 do you have and which ROM did you flash??
Yes thats correct.
When i turn the device on wile holding vol up-down i get a grey screen to
"This operation will delete all your personal data, and reset all settings to manufacturer default. press vol up to restore or press any other keys to cancel"
and im not sure what HTC HD2 i have..
Model: T8585 ?
I flashed the latest rom from the HTC website using the S/N
"RUU_Leo_S_HKCSL_WWE_3.14.831.3_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship"
Okay, get to that screen and press volume up to continue, this will perform a hard reset which is recommended after a flash, your device should then boot up, may take a few minutes as its the first time..........
ok, It finished in like less then 10sec but there was not skips did from 1% - 100% smoothly and says "Restore....Completed Press VolUp to boot"
So i pressed volume up and once again stuck on the tri colour screen
any more suggestions or is my phone dead?
Hmmm
Phones not bricked because 95% of the time if you can get to bootloader the problem can be fixed........
I have the feeling this is something obvious that Im not picking up on.
Chances are someone else will see this and point out the obvious but at the minute I cant think why it might be doing that......
You could try flashing the ROM from SD card.
Rename the file on your PC to "leoimg.nbh" and put it on a 2gb/4gb sd card, turn the phone off, put the card in, turn on and it should flash........
Like I said, i dont think your phone is dead, I think Im missing something obvious....
its weird because i can install roms, hardspl's and all that stuff it knows the phone is there and installs them but for some reason it never gets passes the hardspl stage.. on each boot.
it accually boots into the tri colour screen in a split second of turning the phone on
Its a longshot but is there any possibility that your volume down button is stuck in the pressed position.........
yeah i have installed off the SD card already. that took awhile but it says everything is ok and installsion has completed.
same problem though once i restart tri-coloured screen pops up.
Im afraid Im not sure about this one...........
I'll keep thinking and let you know if anything occurs to me.....
Im sure someone else will chip in at some point and point out the issue though.
alright no worries thanks for the help and time hopefully someone knows what the problem is.
Maybe if i uninstall the Hardspl? might totally wreck it and 100% brick my phone if it fails but I think its the only option ill have left soon
uninstalling hspl shouldnt cause any harm........
I didnt realise you had HSPL installed, I take it you instaled that after flashing the stock rom??
If you have HSPL installed......
Try to install a custom rom, ie an energy rom, just as an experiment........
dunno if youve seen the images yet conan, but unless its changed since, the OP has 3.03.0000
also, if he has magldr installed ( i didnt see it mentioned, but..) when you hard reset it takes just a few seconds, because it is only hard resetting magldr (at least thats my understanding, and would offer a reason why hard reset is so quick)
I suspect incorrect 3,14 flash, which didnt complete so its returning to bootloader,
so, OP, bootloader - hspl4 - 3.03.hspl - flash your 3.13 rom again, over usb.
ok thanks ill try that right now, also yes magldr was installed for android but i thought I got rid of it once i rebooted the offical HTC rom.
If this works im donating $20 to you right away no joke .. ive been trying to fix for 13hours straight
Australian icon said:
ok thanks ill try that right now, also yes magldr was installed for android but i thought I got rid of it once i rebooted the offical HTC rom.
Click to expand...
Click to collapse
sd card flash, right?
Step 1 of the flash is the spl gets overwritten by the one in the leoing.nbh rom (3.03.0000 in this case) and then the phone reboots, and starts to flash , , splashscreen (where magldr is), radio, rom.
BUT, the phone wont allow the flash to start because hspl is now gone, so it fails CID checks and stops, so doesn't remove magldr, radio, rom, nothing, it just stops. Further attempts at flashing fail because you teh user haven't notived the spl change, you assume the whole flash failed, and that hspl is still there.
You shouldnt be able to get that far normaly, it would fail before it even starts, on a stock spl, except that hspl was there, so the flash was allowed to begin.
Ok, so its on SPL-3.03.HSPL now then I installed the latest HTC offical rom with USB but still no go
also if it is resetting magldr how come it doesent load up like it used to after a reset
Hello,
this will be a pretty extensive post, but I want to give you as much info as I can so you can help me
I got a second had EU HD2 with a stock bootloader, radio, rom, ect.
Bootloader: 1.42.0000
Rom: 1.66.479.2 (76641) WWE
Radio: 2.07.51.22_2
Protocol: 15.32.50.07U
I read the forum for a couple of years now and I'm pretty familiar with all the procedures for flashing (I own a couple more htcs,
flashed in every possible way)
The problem is that the battery life is very poor: after a hard reset, so no previously installed apps, not using gps, BT, WiFi, or
anything (even phone in airplane mode), I get 6-7 hrs battery life. Even in standby the battery drains at almost the same rate.
SpoonCharge says -140ma - -150ma with no app or anything in airplane mode. I tried 2 more batteries known to go over 2 days with other
hd2s.
So, I decide the problem might be in the rom and go ahead to flash to a new one:
I chose the Artemis v.65 - http://forum.xda-developers.com/showthread.php?t=612580
I read all the instructions and all other linked to them threads. Started flashing to the stock LEO-S 3.14 with the instructions here -
http://forum.xda-developers.com/showpost.php?p=8776196&postcount=26465
Flashed to SPL 1.66.0000, as said in step 2.
Tried to enter bootloader with VolDown and PowerOn, but it just starts the OS. From inside the OS I can enter bootloader with the EndKey
from johcos but ONLY that way! I tried another bootloader, 1.66HSPL, 2.08 SPL and HSPL, 3.03 SPL - nothing - I cant enter bootloader
manually - only through the EndKey with booted OS.
SO - why the hell??
I can go into bootloader through the EndKey, but I fear flashing because if something happens and the flashing doesn't go as expected I
wont be able to enter bootloader and fix things, no matter with USB sync or SD!
At one (brave) point I tried to flash the RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship from here -
http://forum.xda-developers.com/showthread.php?t=623283 - but it got to 1% and displayed an error: "Update utility not compatible with
device" or something similar.
So, bottom line after this long read:
1. Why/How can't/can I get into bootloader manually?
2. Why at the first place the batt life is so poor with all processes around 0%?
Thank you for the time spent reading my story!
and
Thanks in advance for any help!
here's some "hepl"
1- post in the corect section. The general forum is for these questions you know. it's quite odd for someone who've read the forums for years to make such mistake.
2- Since it's a second hand device, god knows what the previous owner did to it.
3- Does the volume down hardware key work when WinMo is running?
4- Do you turn on the device while holding down the volume down key, or do you press it after it starts, or release it before it starts?
5- I'm pretty sure the artemis build you're trying to get needs SPL 3.03 which you can get here: http://forum.xda-developers.com/showpost.php?p=11499585&postcount=3
6- try your device with SD removed. And make sure you haven't installed any program that runs in the background on the SD.
that's all I can help with
I'm very sorry for the wrong section. I was late and I was frustrated with many hours of struggling with the hd2. Please someone move it where it belongs.
@Dr.Move - thanks for trying to help!
I got it from a friend of mine and can assure I has handled well and it's never been to any kind of repair. It was never even flashed.
All keys work in WinMo.
I hold the VolDown key before pressing the PowerOn key. Tried also holding both keys together, holding VolDown and reseting with the reset button. Manual hard reset with VolUp and VolDown and PowerOn also doesn't work.
Artemis does need SPL3.03, but the flashing instructions say flashing SPL 1.66.0000, than stock 3.14-S which flashes to SPL 3.03.0000 and radio 2.15 .50.14, than Artemis. But that doesn't really matter right now, as it has nothing to do with me not being able to manually enter bootloader or hard reset.
Tried with SD in and out, formatted it (not quick) - all the same.
A thing I forgot to mention. My friend said the hard buttons didn't work, before I got the device. It happened a year ago, when we had no htc service in our country (Bulgaria) and the device had to be sent abroad, so he ditched it and got a new one. He couldn't remember what was wrong with the buttons, but it surely wasn't not being able to enter bootloader, as he doesn't even know what that is.
When I power up the device all the buttons worked and still work. (He was surprised and said "Well - good for you ).
So I'm starting to think the problem might be in the VolDown button, but the PowerOn obviously works. How can it be the buttons work in the OS and not before it boots up??
Ok, update.
I know what you're going to say, I did probably the dummest thing I could. I know now...
I did task 29, wiped the NAND. VolDown + PowerOn still doesnt work.
So empty nand and cant enter bootloader.
Is there anything I can try, what can be the reason the VolDown doesn't work (the button itself DID work in WinMo).
Can something be done or i got myself a shiny black brick?
damn
Sorry for that bro, I think you should move to the general forum now and ask there.
make sure you state your problem in the title clearly, much like you did here.
I'm sorry I can't help you any further as I'm not a developer/electrician. but seems I don't need to tell you that you shouldn't have done that before making sure the buttons worked.