Hi, Excuse me if this has been answered already but I couldn't find it if it has!
I'm trying to upgrade my M3100 to WM6 - Schaps 4.31. I've unlocked the phone and installed Hard SPL v7. When it goes through the Schaps upgrade, I get to the final 'next' button, press it and then the progress bar appears. The M3100 screen goes blank, activesync closes and then the upgrade hangs. Then a Error 260 conection message comes up and, after a few minutes, the M3100 bursts into life.
I've tried resetting the PC and the M3100 with no sucess. I am using Activesync 4.5 & Windows XP SP2
Any help is appreciated. Thanks.
Phil
Try disabling all firewalls, it may be worth trying to flash using the SDCard method. This is a very common issue I'm sure if you search the forum for 260 you will find loads of entries.
Also have a read of this which should help you.
http://forum.xda-developers.com/showthread.php?t=299462
The official Orange M3100 ROM (and probably most official ROMs) comes with a doc which explains all of the error numbers and what to do.
My suggestion would be to do the following as you'll be told to try this before looking further into it:
instead of connecting to ActiveSync and running the update .exe file, do this:
Disconnect device from desktop PC altogether;
Open ActiveSync;
Go into File > Connection Settings and UNcheck the 'allow USB' option - odd as that may seem;
Put your Hermes into bootloader mode (press and hold left-side 'ok' button and right-side 'power' button whilst soft-resetting with stylus), seeing tri-colour screen and the word 'Serial';
When in tri-colour screen, with 'Serial' displayed, THEN connect device to desktop PC via USB cable, even though you've disabled USB connections;
'Serial' will change to 'USB' on the tri-colour screen;
Run the update from Schap's or whoever.
Hopefully that will have worked. Good luck, mon ami.
Chunkymonkey, Progress I think....
Bootloader screen comes up but now I get 1% progress on the update and then Error 244 Invalid Model ID.
For info - bootloader screen reads:-
IPL-1.04
SPL-2.10 Olipro
Thanks
pbunn said:
Chunkymonkey, Progress I think....
Bootloader screen comes up but now I get 1% progress on the update and then Error 244 Invalid Model ID.
For info - bootloader screen reads:-
IPL-1.04
SPL-2.10 Olipro
Thanks
Click to expand...
Click to collapse
Invalid Model ID?
Although you have Olipro's clever rework of SPL on (good), have you also Super-CIDed your M3100?
chunkymonkey said:
Invalid Model ID?
Although you have Olipro's clever rework of SPL on (good), have you also Super-CIDed your M3100?
Click to expand...
Click to collapse
I thought I had - I tried a Vodafone SIM card in it and it worked. I'll do it again to be sure.
Phil
Chunkeymonkey,
Used HTC Hermes SIM & CID Unlock - v3a to Super-CID - I still get the error 244 Invalid ID....
Phil
are you connecting thru a usb hub/multi port,if so dont,,,,,, only connect thru a direct usb connection
pbunn said:
Chunkeymonkey,
Used HTC Hermes SIM & CID Unlock - v3a to Super-CID - I still get the error 244 Invalid ID....
Phil
Click to expand...
Click to collapse
Odd. Should only do that when the Hermes believes the ROM you're using isn't meant for it.
Can't remember if the Super-CID happens automatically with the SIM-unlock using that tool or if it is optional. If it was optional, might want to make sure it actually IS super-CID as you might just be sim-unlocked maybe.
To check CID status use mtty.exe. Put your phone into bootloader, disable USB connections in ActiveSync on desktop PC (File > Connections > Disable USB connections) and then plug Hermes to PC. Run mtty and type task 32. Response "Level=0xFF" means it's NOT Super-CID. Response "Level=0" means it IS Super-CID.
Came back with "level=0" but still no joy flashing the rom.
I'm trying to upgrade my M3100 to WM6 - Schaps 4.31. I've unlocked the phone and installed Hard SPL v7. When it goes through the Schaps upgrade, I get to the final 'next' button, press it and then the progress bar appears. The M3100 screen goes blank, activesync closes and then the upgrade hangs. Then a Error 260 conection message comes up and, after a few minutes, the M3100 bursts into life.
I've tried resetting the PC and the M3100 with no sucess. I am using Activesync 4.5 & Windows XP SP2
Click to expand...
Click to collapse
I had exactley the same problem with my M3100.
Try using a different USB port on your PC. Don't what the difference was but it worked for me.
Re downloaded Schaps_WM6Pro_Hermes_4.30_WWE_Full.exe and all seems to work OK. Not sure if there was an issue in the original download but it all looks cool now.
pbunn said:
Re downloaded Schaps_WM6Pro_Hermes_4.30_WWE_Full.exe and all seems to work OK. Not sure if there was an issue in the original download but it all looks cool now.
Click to expand...
Click to collapse
probably would have been worth loading 4.31 WWE. Very stable and fast.
pbunn said:
Re downloaded Schaps_WM6Pro_Hermes_4.30_WWE_Full.exe and all seems to work OK. Not sure if there was an issue in the original download but it all looks cool now.
Click to expand...
Click to collapse
Nice one mate
Now gone to version 4.31 and the phone skin has gone back to the old style.
Do you know where I can get the updated one from? Is there a cab file available?
if you go to --> Start > Settings > Today it should show a list of themes you can apply. just select one and press 'ok'. sorry if this isnt what u mean
raggers said:
if you go to --> Start > Settings > Today it should show a list of themes you can apply. just select one and press 'ok'. sorry if this isnt what u mean
Click to expand...
Click to collapse
Raggers,
No that's not what I mean. In version 4.30 there was a different phone pad tothe one I have with version 4.31 - it has gone back to a wm5 type. Also - there is no 'Airplane' mode in connection manager that allows me to turn everthing off in one hit.
Related
Apparently, I'm pretty stupid.
I just got the Cingular 8525; I have spent two hours on this site.
Things I've noticed:
One page says go into bootloader; one page says not to allow usb connections.
I do not know if I am supposed to have my non-Cingular SIM card already in the phone when attempting to do anything.
I have seen connect via USB and use mtty (with what settings do I use when I click on USB from the dropdown menu (if any) and do I connect with mtty via USB in bootloader or when the phone has booted into Windows 5.0 and again what about the non-Cingular SIM card?).
I have flashed my computers BIOS several times but I do not understand how to flash this phone based on the myriad of instructions all over this site (and RFTW did not help which is why I am here with 40000000 questions).
The steps to go from SPL 1.06 to an unlocked SIM/CID phone are?
Things I do understand:
I have SPL 1.06 (I know this from bootloader).
I must downgrade to 1.04 from 1.06 then run the upgrade to 1.06 from the Hermes Upgrade wiki page (I already downloaded all of the Cingular files).
Thanks in advance for any clarification.
I unlocked my 8525 last week, I had bootloader 1.06 so I downgraded to a ROM with boetloader 1.04(you can find it here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades ).. then just follow the instructions in the zip file you downloaded(i used HERM_Unlock_v2a), which are:
1. Enter bootloader mode on your Phone. To do this, simultaneously hold side OK and POWER buttons together and reset with stylus.
[You should see SPL-1.04 on the top of the tri-color screen, if you see SPL-1.06 this unlocker will not work, please wait for the next version]
2. Connect your phone to your computer using the USB lead.
3. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with a patched radio ROM required to unlock.
4. Wait patiently.
5. Once the MaUpgradeUt_noID.exe upgrade completes, it will end up saying "Upgrade Error 114", but the patched radio ROM will be flashed anyway, dont worry about that error!
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
7. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the HERM_Unlock_v2a.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
8. Run HERM_Unlock_v2a.exe on your phone. Wait about 1 minute.
9. You should see a "SUCCESS!" message from HERM_Unlock_v2a.exe, after that soft reset your phone.
10. Process is (hopefully) complete!
11. If the phone requests unlock code when you put a locked SIM, the code is: 22051978
I assume I want go to 1.04 for Cingular which is 1.30.502.1.
What about my SIM card? Is it supposed to be in phone when I run this file? (it's a t-mobile sim).
I assume the activesync connection via usb is okay? I cannot get it to connect (even though the phone is on and booted into Windows 5.0); is this because I have not inserted the SIM card into the phone? Note: after I unplugged the device, setting allow USB connections on the device in the ActiveSync settings, then plugging it back in, it connected via USB in ActiveSync (4.2). However, I just got a box saying the version of ActiveSync is not compatible with this mobile device. This occured after I started the installer and it showing Verifying the information on your PDA phone.
I received an update error 260 since it thinks the phone is not connected via USB (and I noticed the ActiveSync icon in the system tray is gone).
I went to check the M$ page to see if there is a later download; there is not. Then, the AS icon return (trying to update outlook, install nero mobile) so I decided to run the installer again and now sees my current version 1.34.502.1 and I have the option to upgrade ROM
MilanoRex said:
I unlocked my 8525 last week, I had bootloader 1.06 so I downgraded to a ROM with boetloader 1.04(you can find it here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades ).. then just follow the instructions in the zip file you downloaded(i used HERM_Unlock_v2a), which are:
1. Enter bootloader mode on your Phone. To do this, simultaneously hold side OK and POWER buttons together and reset with stylus.
[You should see SPL-1.04 on the top of the tri-color screen, if you see SPL-1.06 this unlocker will not work, please wait for the next version]
2. Connect your phone to your computer using the USB lead.
3. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with a patched radio ROM required to unlock.
4. Wait patiently.
5. Once the MaUpgradeUt_noID.exe upgrade completes, it will end up saying "Upgrade Error 114", but the patched radio ROM will be flashed anyway, dont worry about that error!
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
7. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the HERM_Unlock_v2a.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
8. Run HERM_Unlock_v2a.exe on your phone. Wait about 1 minute.
9. You should see a "SUCCESS!" message from HERM_Unlock_v2a.exe, after that soft reset your phone.
10. Process is (hopefully) complete!
11. If the phone requests unlock code when you put a locked SIM, the code is: 22051978
Click to expand...
Click to collapse
crazyut said:
I assume I want go to 1.04 for Cingular which is 1.30.502.1.
Click to expand...
Click to collapse
right
crazyut said:
What about my SIM card? Is it supposed to be in phone when I run this file? (it's a t-mobile sim).
Click to expand...
Click to collapse
doesn't matter
crazyut said:
I assume the activesync connection via usb is okay?
Click to expand...
Click to collapse
It is ok, but generally it causes more problems than it helps. Best is to disable the checkbox that says "enable usb connections" on activesync settings and you'll see the icon on the system tray turn gray with a red "X". Then you need to start the RUU when the device is in bootloader mode (tri-color screen). After you have upgrded the rom (or radio rom) you can reenable activesync again if you want.
crazyut said:
I cannot get it to connect (even though the phone is on and booted into Windows 5.0); is this because I have not inserted the SIM card into the phone?
Click to expand...
Click to collapse
SIM card and activesync have nothing to do.
crazyut said:
I received an update error 260 since it thinks the phone is not connected via USB (and I noticed the ActiveSync icon in the system tray is gone).
Click to expand...
Click to collapse
Icon was gone because RUU checks your current rom version using activesync and then kills it an put device in bootloaer mode. If RUU cannot kill activesync correctly errors happen:
You will avoid the 260 error if you disable usb connections on desktop activesync as I told you, and start the upgrade in bootloader mode... only difference you'll notice is that RUU will not report your current rom version.
Hey. I left the RUU software running (the 25+ minute variety) while I went to buy a case and care charger. I came back and evidently, the phone had rebooted because, it is at the Windows Mobile screen to setup the Windows Mobile device. I assume it is safe to do the 2a software. After that, am I able to update the RUU back to 1.06?
Thanks for your help, Milan and pof!
I rebooted into bootloader to confirm successful downgrade to 1.04 from 1.06 and it was. The RUU software from the upgrade page for Cingular appears to have been successful.
I am now going to attempt the 2a software.
Yes, now follow all the instructions on sim&cid unlocker v2a, and when finished, flash the cingular 1.34 rom again.
pof said:
Yes, now follow all the instructions on sim&cid unlocker v2a, and when finished, flash the cingular 1.34 rom again.
Click to expand...
Click to collapse
It's now on the upgrade screen to Radio 1.16.00.69 but it does not show the previous version. Is this normal? I have not pressed upgrade yet. I have the splitter with the AC and USB cables into the phone (currently in bootloader mode at SPL-1.04).
yes, it is normal... i told you before:
pof said:
RUU checks your current rom version using activesync
[...]
start the upgrade in bootloader mode... only difference you'll notice is that RUU will not report your current rom version.
Click to expand...
Click to collapse
pof said:
yes, it is normal... i told you before:
Click to expand...
Click to collapse
I got the 114 error as promised in the readme. I exited the program using the EXIT button.
The next step:
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
On the phone display, it still shows Upgrade Radio Stack Please Wait..
The soft reset is the simultaneous OK and Power?
I just took the battery out and reset; it appeared to go okay. I copied the exe file to the phone and was able to run the file as in the readme. I then reset the phone, put in the t-mobile sim and it works.
Thanks much to POF and Milan for their straightforward approach. You can use this thread as a tutorial!
Is there any reason I should add the 1.06 file back to the unlocked 8525?
SPL 1.06 to SPL 1.04 back to SPL 1.06?
Hi:
I followed pof's (with pof's help) tutorial on how to unlock the Cingular 8525. I am currently at SPL 1.04 (downgraded form SPL 1.06) and had run the v2a software to unlock. It works great with T-mobile (I was a Cingular customer but made the switch).
My questions are:
Is there any reason to go back SPL 1.06?
If I do go back to SPL 1.06, it does not affect the unlock status of the SIM or CID?
I still am confused about the Radio and what that does in relation to the CID, SIM, or phone. I assume the Radio is affected the SPL version that you have?
I have tried to peruse through various pages regarding downgrading (the 13 page thread for example) to see if that question is answered.
The radio ROM controls the GSM/GPRS/UMTS hardware in your hermes. You cannot independently upgrade it unless you are running SPL 1.04. There is no reason IMO to go to any other bootloader version.
Sleuth255 said:
The radio ROM controls the GSM/GPRS/UMTS hardware in your hermes. You cannot independently upgrade it unless you are running SPL 1.04. There is no reason IMO to go to any other bootloader version.
Click to expand...
Click to collapse
Oh okay, that clears up yet something else I did not understand
Thanks for the tip on the bootloader version; I will leave it at SPL 1.04.
That being said, I am currently in the middle of the Radio 1.20 thread; I have not finished reading it yet (I can only do so much at work before people wonder what I am doing). Have you upgraded to Radio 1.20? If not, what radio are you running and what do you think of its stability and/or functionality?
Thanks!
I'm running the 1.20 radio. It and the 1.35 TyTN ROM are the best combination I've used so far.
Ok, I've been trying to update my 8525 for hours...here is my problem. First, I tried to HardSPL-v7 but I kept getting an "Error [240] File open". I think this is preventing me from doing any ROM update. When I try to run the Cingular ROM update activesync shuts down and I get a connection error, I think it is "error [260]". I have wiped or cleaned out my 8525 so that I am back to day one. I have tried both ROM updates on 2 separate computers and I get same error messages on both computers. I have searched the Wiki's but have found nothing, so please help. As you can tell, I am a virgin to ROM updates so please go gently.
I should add, my present ver. ROM AKU 2.3 (1.34.502.7018.01H) SPL 1.06 IPL 1.01. Radio is 1.16.
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
mrvanx said:
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
Click to expand...
Click to collapse
I have, I have even tried the mtty "fix" but I had problems with that as well. I get a modem connection screen but there is nothing about a USB connection.
Bit more info would be nice, which ROM are downloading, and where from??
Also what procedure are you doing to update?? EXACT info please.
mrvanx said:
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
Click to expand...
Click to collapse
Ok, I just tried it 2 more times, Hard-SPL. It flashes to the 8525 and goes into bootloader and shows the following "HERM100 IPL-SSPL by Des HERM100 SPL-1.09.ds" at this point activesync 4.5 shuts down the 8525 is stuck in bootloader (it never reboots) and after a few minutes I get "Error [260] Upated Error". Hard SPL shuts down and the 8525 is stuck in bootloader mode. At this point I have been disconnecting the USB cable and doing a soft reset, once the phone is on, I go into bootloader and the old info shows up SPL 1.06 and IPL 1.01.
Let me have a think, firstly do you have the latest versions of the .net framework installed?
I was able to finally run HardSPLv7, I had to do it on another computer. Now, I would like to update to RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe. I assume I should use the same computer that I used to successfully run HardSPL. Do I need to rebuild the rom file with RUUWrapper.exe (CustomRUU by olipro) & Dutty's Good NBH Tool, before running the RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe update?
mrvanx said:
Let me have a think, firstly do you have the latest versions of the .net framework installed?
Click to expand...
Click to collapse
I have .Net 1 thru 3.5 (pre-release) installed on the computer that I can not get to run any ROM updates.
9
compudds said:
I was able to finally run HardSPLv7, I had to do it on another computer. Now, I would like to update to RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe. I assume I should use the same computer that I used to successfully run HardSPL. Do I need to rebuild the rom file with RUUWrapper.exe (CustomRUU by olipro) & Dutty's Good NBH Tool, before running the RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe update?
Click to expand...
Click to collapse
Yes if you carry on the guide past flashing hardspl you will get the radio updated aswell.
Can i ask, what is different on the computer you used???
mrvanx said:
Yes if you carry on the guide past flashing hardspl you will get the radio updated aswell.
Can i ask, what is different on the computer you used???
Click to expand...
Click to collapse
Off hand, the major difference would be Intel (worked) vs. AMD (failed) but I doubt that is the problem, you would be flooded with questions due to so many computers that have AMD chips. The USB cable was the same as well. I'll have to think about that...
Definatly check your "failed" computer is up to date with .net and everything else, most likely a software problem.
I have this problem as well..
AT&T 8525 windows moble 6 trying to install the hardspl v7.
v3.5 and 3.0 .net framework.
the RUUwrapper program gets to the 'verifiying info' screen then give me an erroe 240 message. 'the update utility can not open the requested file.'
any help would be great. Looking to add the touch it interface.
thanks,
Mike
Read the post Hard SPL at the top of this forum and go to page 116 ( I believe its post #1160) and use the sd card method. You don't need to use the pc at all. I generally flasah ALL os's using the sd card method as it seems to be safer then using the usb method. No "sync errors" to deal with.
Cheers...
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
blackphnx said:
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
Click to expand...
Click to collapse
I loaded it thru the sd card just as the post above suggested. It loaded the hardspl just fine. My PPC seems to run faster as well.
Thanks for the help! it is much appreciated.
blackphnx said:
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
Click to expand...
Click to collapse
One thing that i have learned from flashing my 8525 is to remove any USB device except the 8525. This has worked for me.
swimmy said:
One thing that i have learned from flashing my 8525 is to remove any USB device except the 8525. This has worked for me.
Click to expand...
Click to collapse
But my mouse is on USB. I might try on different computer and post back the results.
UPDATE
I tried using my friend's laptop and it installed without a problem. I think the issue is with the .NET framework. I installed the latest one before flashing and it worked fine. Hmmm.. Im not sure about this tho.
Hello.... Try the sd card method. You don't need the computer...
Sorry if I sound condescending, but, I seem to find a lot of people saying that they have sync problems. Solution, Take the pc out of the equation (except to load files onto sd card). It is SOOO much safer then using the pc, no "sync" problems, no chance of usb being disconnected, reset button being hit or , worst case scenario, power failure...
You have to either have little or no battery power or MANUALLY hit the reset button with the stylus to stop the flash...
And thats my 2 cents....
Refer to post #13 to find out how to use sd card method to flash hard spl...
Cheers...
sd card method???
how?
Ok...I have been through all the posts about upgrading etc. I still have a problem and I'm sure that I'm overlooking something....but I can't figure it out on my own. Here is what is happening (it does the same thing with every RUU that I've used...the DST fix...upgrading to WM6....etc)
1. I run the RUU and let it go through its routine (extract files, verify info on pc, etc.)
2. I check the box that says I have read the readme and click next
3. The next screen appears and it has the following steps:
Connect to the USB cable (check)
Establish an ActiveSync Connection (check)
Disable standby and hibernation on PC (check)
Make sure batter is > 50% (check)
Then I check the box and click next
4. I pick the update and click on the update button
5. I verify that I want to upgrade my phone from ROM verion x.xx.xxx to x.xx.xxx and click next
6. The program tells me that I am finally ready to update...and if I am sure I want to proceed to click next...so I click next
7. As soon as I click next...the progress bar comes up on my pc and my phone goes into standby mode (no bootloader...just standby). The progress bar never moves.
8. After a minute or two the RUU give me the ERROR [260]: Connection
9. I reboot my device and repeat steps 1-8
10. I reboot my device and my computer and repeat steps 1 - 8.
Now if I leave my device connected to the usb and close out the RUU after it gives me the ERROR [260], and then run the RUU again...when it is first verifying the information on my pc (before it asks any questions and before it tells me to connect my device) it will throw the device into bootloader mode. If I try to keep running the RUU while the device is in bootloader mode it give me the error that my device is not connected. I have tried and tried...maybe one of ya'll can help me. Thanks in advance
Chris
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
gerald_s said:
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
Click to expand...
Click to collapse
XP
No firewall
I tried to flash the WM6 from AT&T I assume its beta
and no did not install the Olipros bootloader
Ok...I think I found out how to do this...Ya'll can tell me if I'm screwing something up.
I go through all the steps listed above until it gets to the progress screen. When it gets there I manually put the the device in bootloader mode (Power, side ok, and reset). Once I do this...the progress bar starts moving. I will let you know if this works...
Hmmmm
Its not the way it should work but if it works its ok
You should have installed Olipros HardSPL first and then try to flash an official rom. If its working then something with your download is wrong.
What ROM is on there now?
Has the phone been CID unlocked?
Oli's CustomRUU is better, you may want to unpack the ROM and put the NBH in a folder with Oli's RUU and then do the upgrade.
BTW, gerald_s is right, you should not have to do that... what you may want to do is put the phone in Bootloader mode manually (while not connected to the PC), then plug in the USB, then start the RUU. That helps some people with 260 error.
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
You may be trying to flash a rom that includes the radio rom. What is your device? Is it possible that your device is a new x01ht with radio 1.14 and radio bootloader 0182? If yes, then you will get this error when you try to flash a rom with this method because during the flash it will be disconnected by the radio bootloader because it is not overwriteable. If you flash using the NBH file on the microSD, it will skip past radio and radio boot and just flash the other parts of the file.
mikebraeuer said:
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
Click to expand...
Click to collapse
If you are running windows XP, just connect the card to the computer, open MY COMPUTER, right-click the removable disk that is your microSD and then click format. Default in windows xp is to format using FAT32 filesystem which is perfect.
The thing is... if you dont know how to format a drive in Windows, should you be flashing your device yourself?
Which Solution???
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Wantoknow said:
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Click to expand...
Click to collapse
Have you tried flashing with your microSD?
Kevbodian said:
Have you tried flashing with your microSD?
Click to expand...
Click to collapse
I forgot to tell that, I had flashed through extra memory card yet, and could be done!
But I wanna flash ROM against CustomRUU through MS Active Sync as I had used before. Can you help me
i have a problem very similar to Chris. when i check the box "yes activesync is syncronised", and then the progressbar shows up and the phone goes into standby.
i've turned standby of in powermanagement options.
my os is XP
i use active sync v4.5
and this is first time i try this.
i've read something about this bootloader, i can get there but then i cannot sync with active sync. so i kinda stuck.
have been searching the forums and this was the same problem as mine but i don't understand your solutions.
//KufrA
--Problem solved--
i did all things without activesync,
1. start phone in bootloader
2. do the install
3. wait 0% to 100%, and done.
is there a problem with active sync or why do i have to do anything with it at all?
Hi does anyone know if there are WM6 ROMs for the SPV C550 if not are there any good WM5 ones?
look topic about wm5 for hurricane, there are also links to wm6 for hurricane device
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Has anybody tried this ROM?
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Ideal thanks
So is the 566.zip the WM5 or WM6 rom and has it been tested?
Whats the new SPL?
hI ALL, can u tell me the mini guide how to install this rom? I did it once to my sda but I dont remember now, where is the nbfupdatetool and RUU and patched RUU..???
when I type l c:\wm6.bin it give me this:
clean up the image temp buffer at 0x8C080000 Length 0x01B00000 MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
cmd>
maybe damaged rom, or any idea?
Gang: Make sure you're CID unlocked. (Eg, when you issue "info 2", it says HTCSuperCID).
How can do that cid unlock? give me some working link to download that tool or something. thx
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
hmm, thx for guide, I believe it will work, but I have little problem : now I cant even connect to activesync so I cant do cid unlock, any idea how to fix that
lazaj007 said:
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
Click to expand...
Click to collapse
Thanks for helping out!
A few questions?
1. This link "http//www.spv-developers.com/content/SPV-Services.zip" takes me to Wikipedia.
2. Where can I find the patched ruu to update the spl. It wasn't in the zip file?
Thanks in advance!
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
gangstaunitg said:
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
Click to expand...
Click to collapse
DoH! I didn't notice the missing ":"
Cheers!
Anybody have idea why I cant connect to activesync after spl upgrade ? Before spl upgrade it all goes well. Can I do something with it?
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
I did it !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THank u all, thankS
This rom is amazing, everything work perfect, and it looks beautiful,
one more time thank you. jUUHHHUUUUUUUUU
lazaj007 said:
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
Click to expand...
Click to collapse
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
MrMiyagi said:
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
Click to expand...
Click to collapse
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
MrMiyagi said:
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
Click to expand...
Click to collapse
Heh heh ... seems I'm posting to myself ... that's cool I like my own company ... So I reflashed the SPL and some of the problems have gone away.
Phone will boot OK now ... but it will still "go to blank screen" and require plugging into the USB cable to "wake it up"
I'm out of ideas now ...
I cant seem to get hSPL working
The executable runs, i get the G3/G4 button, press it, after a while the screen dissapears, 1 flash of what seems to be a cmd-prompt but thats it
The device looks not affected in the whole process.(no white screen/flashes or any other indication of a tranfer of any data)
Bootloader check confirmes the problem by still showing IPL/SPL: 2.18.0001
Its a non-branded QTEK-9100. So no Simlock. Anyone can supply a way to get hSPL on the device?
Galaphile said:
I cant seem to get hSPL working
The executable runs, i get the G3/G4 button, press it, after a while the screen dissapears, 1 flash of what seems to be a cmd-prompt but thats it
The device looks not affected in the whole process.(no white screen/flashes or any other indication of a tranfer of any data)
Bootloader check confirmes the problem by still showing IPL/SPL: 2.18.0001
Its a non-branded QTEK-9100. So no Simlock. Anyone can supply a way to get hSPL on the device?
Click to expand...
Click to collapse
You could try to use another PC, another USB connection.
You could also try to enable Rapi manually (or by using mestrini's WST).
I would try on an other PC though, I have seen troubles with certain stripped/corrupted XP versions and Hard/soft SPL before.
Well Add to your list of not working Os-es WinFLP (strange because just earlier i completed an Trinity HardSpl)
But on my normal XP station the screen does not turn white.
The display is corrupted I see my radio signal status Icon and the Battery Icon in a Black bar,
Below the Date/time
and the rest of the screen is Black with in small green charakters the 'error'
"Unable to open log file ...
Tiny_console_init Done ."
EDIT: Second time it went white... And spl from olipro installed like a charm....
Help me to resolve
Every time i switch on device
IPL 2.17.0001
...
...
SPL 1.01
what is this? how can i resovle it, all questions i will answer, help.
I answered your question in the other thread.
-MyHTC- said:
I answered your question in the other thread.
Click to expand...
Click to collapse
where? please send me url
This is what you have:
IPL 2.17.0001 = G4
SPL 1.01 = G3
Your phone is bricked.
I don’t know of anyone who has recovered from this.