hey there been a member for sometime and have tried to search for a solution to my problem and am abit confused.
and sorry if its such a newb question (dont burn me for it)
i have an o2 atom exec (using RC3 rom with touchflo) and yesterday i /soft reseted/ the phone because it was acting funny, after the reset it would be stuck at the startup screen and would not load past that the whole day, so i waited and re-tried in the evening.. the same thing occured... i was at the time able to load into bootloader (MN2) but then could do nothing else.. so i searched throughout the forums and found a post by 'chartreux' http://forum.xda-developers.com/showthread.php?p=1684559&highlight=EBOOT.NB0 but had not read the entire post and proceeded to load (mn1) onto my phone via mini sd card and it worked, my phone was working again, it performed a hard reset and restored it to factory settings (ie: calendar, msgs, contacts, software all gone) and phone is working normally again... since it has done this i wanted to update to 'wm6.1 atom exec rom' just to be up-to-date and have synced it via activesync and have run "DSUU" but my phone just restarts and loads the current rom i have installed! and just repeats everytime i have tried (have tried atleast 50 times)
so my main question.. is my bootloader dead? i know my phones not bricked since its still working perfectly im just not able to upgrade my ROM but can still do everything else (such as browse through files, run programs, make calls)
and last of all.. can anybody please help?! as i am at the point running the phone over with my car!
and once again am sorry for the stupid question.. =/ and thanks for hearing me out!
cheers!
stylistik said:
hey there been a member for sometime and have tried to search for a solution to my problem and am abit confused.
and sorry if its such a newb question (dont burn me for it)
i have an o2 atom exec (using RC3 rom with touchflo) and yesterday i /soft reseted/ the phone because it was acting funny, after the reset it would be stuck at the startup screen and would not load past that the whole day, so i waited and re-tried in the evening.. the same thing occured... i was at the time able to load into bootloader (MN2) but then could do nothing else.. so i searched throughout the forums and found a post by 'chartreux' http://forum.xda-developers.com/showthread.php?p=1684559&highlight=EBOOT.NB0 but had not read the entire post and proceeded to load (mn1) onto my phone via mini sd card and it worked, my phone was working again, it performed a hard reset and restored it to factory settings (ie: calendar, msgs, contacts, software all gone) and phone is working normally again... since it has done this i wanted to update to 'wm6.1 atom exec rom' just to be up-to-date and have synced it via activesync and have run "DSUU" but my phone just restarts and loads the current rom i have installed! and just repeats everytime i have tried (have tried atleast 50 times)
so my main question.. is my bootloader dead? i know my phones not bricked since its still working perfectly im just not able to upgrade my ROM but can still do everything else (such as browse through files, run programs, make calls)
and last of all.. can anybody please help?! as i am at the point running the phone over with my car!
and once again am sorry for the stupid question.. =/ and thanks for hearing me out!
cheers!
Click to expand...
Click to collapse
what version of your bootloader now? MN2 or MN1? if still MN1 please read again the thread to update your bootloader to MN2 (since your device is ATOM EXEC).
and after done, please check when you run DSUU, see on the left bottom whether have a drop down box or not? if yes then choose "ALL"
hope this can help to solve your problem.
hey! thanks for the reply mate!
but im not sure i cant check the version of my bootloader...
wont let me get into it by pressing camera+SR or camera+off button..
just boots straight into the operating system.
and, as for the DSUU it just restarts the phone after i choose all, and goes through to the today screen on the phone, and as for the DSUU update its stays at the screen which shows "The current software is now being updated from your device."
followed by an error appearing after a few minutes showing " No download target was found!!" even though my atomexec is synced
which is then followed by the "connection error" screen.
please help.. this is seriously pissing me off...
stylistik said:
hey! thanks for the reply mate!
but im not sure i cant check the version of my bootloader...
wont let me get into it by pressing camera+SR or camera+off button..
just boots straight into the operating system.
and, as for the DSUU it just restarts the phone after i choose all, and goes through to the today screen on the phone, and as for the DSUU update its stays at the screen which shows "The current software is now being updated from your device."
followed by an error appearing after a few minutes showing " No download target was found!!" even though my atomexec is synced
which is then followed by the "connection error" screen.
please help.. this is seriously pissing me off...
Click to expand...
Click to collapse
try to downgrade again your bootloader to MN1 (please do it step by step). as long you can secure your bootloader, hopefully you can resolved your problem.
remember to upgrade again to MN2 once you able to downgrade to MN1 before try flashing to wm6.1.
good luck.
still cant access bootloader.. even when trying DSUU it just boots straight into the operating system, when trying to update and also i tried the MN1 bootloader again and tried to get into it... still nothing.. it just resets, i tried it with my 4GB mini sd, 2gb msd, and a 64mb mini sd.. could not get into it... sigh...
Ok try a deep breath and read all the posts on dead boatloaders and other upgrading problem posts through and through. Then try to change ur USB cable and what system are u using i.e XP or Vista????
thankyou kindly, for the suggestions i have been reading through alot of posts and tried alot but.. nothing so far.. i guess its not too bad since its stuck on windows mobile 6 with abusalzas rom..
im just annoyed i cannot upgrade to the latest 'rom' and since my phone 'had' to perform a hard reset why not update so yeh.. and i am using windows xp for my computers os.
Did u change the USB cable mate, once I had to do it and the interesting thing is that the same USB cable was working perfectly for other things but causing problems when connecting to my Atom Exec.
yeh tried it with my old v3 cable didnt work has the same outcomes.. sigh.. i might try that dead bootloader hardware and software recovery from this post by Alex_Beda & 1stMASTER
http://forum.xda-developers.com/showthread.php?t=336278
what you think?
although my phone doesn't resemble there symptoms list.. as it still works and everything just cant get into the damn bootloader.. :/ when done manually and when trying to upgrade..
Did u read this mate ?????
http://forum.xda-developers.com/showthread.php?t=358442
You just try the DSUU with upgrade "OS" only and not "ALL".
alright cheers buddy! ill try it out and i hope it works!!
bahh.. didnt work =( just restarted my phone and gave me a connection error screen on my computer....
Actually i have the same problem, i tried to get into the bootloader by press and hold camera + reset button it just restart and load the WM
Dead atom exec
My atom exec having problem ( dead ), so after press camera reset sw my atom can booting normaly but touch screen function only for entering password and then touch screen not response anymore. I check the system information by touch the button (manualy) but IMEI not ready and Radio not ready.
Pls someone can help us.
o2 atom bootloader
hello
my o2 atom bootloader screen mn1 dignostic manger screen remains after rom flashing .i tried flashig orginl rom and pedvit rom but bootloader screen comes again .not starting my mobile please help
Related
well i did the silly thing and did a flash upgrade on my atom exec to WM6 v7
it went 100% restarted fine
but now!!!!! im stuck on the align screen it doesnt listen to my taps, if i move my fingers all over the screen it eventually pick it up but it isnt accurate enough so keeps restarting the test align session... HELP PLEASE i have meetings comming up and need this phone
i can get into boot loader mode but when i connect phone to laptop it doesnt connect active sync while in bootloader mode...
can i skip this screen align somehow
You are not suppose to upgrade the EXEC with the ROM .
Check out the WIKIPEDIA ATOM solutions page for assistance.
I think therz a way to get back to the ORIGINAL ROM , ask a SENIOR for help also search the forums for older posts , i remember someone with ths same problem as yours
really? i just ran the utility here:
http://forum.xda-developers.com/showthread.php?t=333165
without making any changes to it
how do i go back to original pleaseeee help someone... if i got in boot loader mode and run the same upgrade utility (as linked above) it lets me click upgrade but then quickly says connection failed and then my bootroom reads:
"please use DSUU in OS mode and sync with PC first!!!
where do i get original and how do i do it please... maybe there should be a sticky for stuff ups like this
wow no one is kind enough to help... ive tried this:
http://forum.xda-developers.com/showthread.php?t=331818&page=1
but it freezes on 6% and i took the advise read in the wiki to hard reboot then run DSUU , and it does the same thing (stuck at 6%)
well now i have the wm5 starting but its stuck again on the tap the screen? ignoring my taps...
could it be my screen is stuffed? although it worked before the flash
okay !!! progress!!!! ....'
ive finally called o2 and put their rom and it works to a certain point, the align screen detects my taps but it just keeps repeating over n over n over asking me to keep taping around the screen???
Hard Reset
I think hard reseting it once should solve the issue...........if it doesn't try reflashing it once again.....worked for me............brute force is needed sometime
no i figured its screwed my digitzer somehow so im asking for calibration data in other post
Obviously I'm a n00b I just got my 8525 yesterday, right away I upgraded to WM6 went all day today with it working fine, I installed a PockMSN and Windows Live anyways to keep it short I FIGURED I WOULD just RE-INSTALL Windows Mobile 6 to get a fresh phone (didnt know hard reset did the same) Actually it was the 3rd time I flashed the OS and RE-UPGRADED to WM6 to get a fresh phone!!!!
~heres the trouble~
In the middle of the reinstalling WM6 I accidentally reset my computer, didnt realize it right away and, got ERROR 260 I believe, anyways I followed the directions, took out the battery and reset, plugged the USB back and RAN the Offical WM6 Rom of HTC site again and it keeps getting stuck EVERYTIME at 11%, I have tried it like 10 times and it gets stuck at 11%, and I get the same ERROR. Says Communication error 260. I have tried everything I know reset the computer, changed USB cords, and Nothing, everytime it gets stuck at 11%!!!!!!
Any Ideas about how to get my 2 day old Hermes back??
(I know i did a n00bish thing and I am sorry)
same place everytime!!
I tried to reinstall Active Sync, changed USB cables, switched USB ports, nothing!! I keep getting ERROR 262 (thought it was 260 at 1st) and wont get past 11% says no connection. I do notice everytime i try this process, Active Sync isnt connected, but the Hermes is connected to the computer! Cause if it cant read the hermes it wouldnt be able to even start the update process. But 11% everytime its stops
nicknowsky said:
I tried to reinstall Active Sync, changed USB cables, switched USB ports, nothing!! I keep getting ERROR 262 (thought it was 260 at 1st) and wont get past 11% says no connection. I do notice everytime i try this process, Active Sync isnt connected, but the Hermes is connected to the computer! Cause if it cant read the hermes it wouldnt be able to even start the update process. But 11% everytime its stops
Click to expand...
Click to collapse
Perhaps you could try to flash using the sdcard method. So you would not be connected to a pc anymore. Who knows, it could solve your problem. I know one case where installing an official rom cured also a similar problem.
Quick summary of the sdcard method:
Use an empty sdcard formatted in FAT32
Copy the RUU_Signed.nbh file containing the OS to the card and rename it: hermimg.nbh
Enter bootloader mode (OK + POWER + Softreset). Normally, after the 3colors screen, you will get "Loading" followed by a description of what is on the card.
When ready, press power and... wait...
Good luck (The phone is NOT connected to the pc)
sounds good but I dont have a MicroSD card reader to do that. And I am using an Offical HTC WM6 ROM, thats all I ever used was the offical WM6 Rom from the AT&T site. Like I said, I was able to install WM6 already, but me being a complete idiot was Flashing the upgrade ROM to get the Hermes back to fresh phone factory settings. But I accidentally reset the computer in the middle of Flshing and since then I have never been able to get it to install again, everytime I turn on the phone I am stuck at the Tri-Color Screen, I am able to restart the upgrade process, but it stops at 11% says ERROR 262 and no connectivity!!
please anybody knows anything, this is the only thing I got, my mom got it for me! We cant afford to get a new one, or even fix it, it was a special present!
nicknowsky said:
please anybody knows anything, this is the only thing I got, my mom got it for me! We cant afford to get a new one, or even fix it, it was a special present!
Click to expand...
Click to collapse
Ok. I am a bit annoyed if you cannot try the sdflash method (BTW you can ask somebody having a PC to prepare the card for you.)
There are different things you can flash on your hermes. Radio, OS, Splash screens, Extended Rom,.... The most tricky thing is the radio rom as a failure there has a higher probability to brick your pda.
This is why i believe it is very dangerous to flash right away without some readings and understanding about what you do. i hope you had some experience here.
Did you first install hardspl (olipro 2.10 )? This is not mandatory but is a very good protection against bricking. (here the excellent guide of mrvanx: http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27 )
Did you flash also a radio rom? (Was it included in the "package" you wanted to flash?) If yes, i am a bit anxious that a stop at 11% is a problem... BUT, if you flashed a radio rom, it goes very, very, very... slowly. And gives the feeling that it freezes. For the "radio" part it is normal . I hope you did not stop the process too soon.
Once again, try the sdcard method. Or try to flash an official rom (most of the time containing a radio part...) and be patient. Can take till 25 minutes.
If this does not work, do not panic yet. Others had also problems before you: go there and start reading : http://forum.xda-developers.com/showthread.php?t=286755 and here http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
There is a hope to solve your problem. Good luck
Try to flash a radio ROM, turn the device on and if it stays at the bootloader screen (the tri colour screen) make a note of the version displayed. Hook up the device with USB cable, dont worry about activesync.
Download and unzip a radio ROM upgrade (try this one), run the exe, select your bootloader version on the screen....follow the screens through and see if it works.....radio roms take ages to flash so DO NOT disconnect your device.....if it doesnt work you most likely have a corrupted radio bootloader.............which is likely since the radio flash takes the longest ammount of time the reset probably occurred halfway through this.................unlucky
Give it a try though.
The lesson to learn here is to READ THRICE and flash once.....never ever disconnect your device out of impatience (which i suspect has happened many times on a radio flash) and be carefull these devices are expensive
mrvanx said:
The lesson to learn here is to READ THRICE and flash once.....never ever disconnect your device out of impatience (which i suspect has happened many times on a radio flash) and be carefull these devices are expensive
Click to expand...
Click to collapse
I could not say better
I know, the MicroSD method is nice, but when I got the phone the guy gave me a MicroSD card, but not the regular SD card to read it on computers ( i do have a card reader) Guys a super appreciate the replies> I am gonna try everything rite now, but real quick is my Hermes FUCT??? or is this error fixable??? It is just losing communication everytime at the exact same place, it just seems like something is fixable, but my sorry luck i cant get over the hump!! I will let ya'll know ASAP
okay, here is the thing, Every Hermes ROM update utility I have downloaded wont work, i start it and the VERIFY INFO ON HERMS windows appears about 2 minutes late I get ERROR 260 and it exits! Now when I use the OFFICAL WM6 upgrade ROM from the ATT/HTC site it seems to read the HERMES and wanna start the upgrade process, but thats where it ends at 11% No other RUU I have used or tried has even gotten that far, I just get ERROR 260 before it starts and I have to exit.
What it looks like is I cant communicate with my HERMES at ALL!! Active Sync wont see, only when I reset my computer and reset the HERMES and I plug it in a different USB port, it says Installing New Hardware and HTC USB something and then Hardware has installed and is now ready to use. But Active Sync wont recogniZe it
I'm sorry to tell you that but i think you ****ed up your phone and it is as useless as my ****ing jasjam.
please give us some detailed info s about your hermes like IPL SPL GSM STATUS....
When I am in Tri Color Mode I see.......
HERM100
IPL-1.04
HERM100
SPL-2.03
and SERIAL at bottom, then USB when I plug it in to my computer
I had upgraded to WM6 before on it, but me being a impulsive FOOL, i flashed it again to get me back to Factory Setting (didnt know HARD RESET did the same) and I accidentally RESET my computer in the middle of ROM Upgrading and ever since I cant get past 11% when I try to do it again (using the OFFICAL WM6 ROM from HTC)
and I cant get any communication with mtty although I dont know much about that app, I get a CANT load screen appear
is your phone KITL enabled.
hold the COMM manager button + POWER button + OK button (the one on the left side under the jog wheel) and reset with stylus.
if you see KITL dialogue then it is KITL enabled (MY bricked jasjam is KITL disabled)
if it is KITL enabled then read : http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES and your phone will be just fine.
if it is not then your phone is ****ed up just like mine
HA HA, me and my phone guy (well the guy who I bought my Hermes from) HAVE FOUND A FIX to get the phone outta Bootloader Mode and back into OS!! in my case WM6!! I have to do it 1 more time to fully confirm the method!!!!!!!! My friend is calling "SHOCKING THE PHONE" but not really shocking anything!! I am reluctant to share the method, but this site needs more people to actually HELP out others
nicknowsky said:
HA HA, me and my phone guy (well the guy who I bought my Hermes from) HAVE FOUND A FIX to get the phone outta Bootloader Mode and back into OS!! in my case WM6!! I have to do it 1 more time to fully confirm the method!!!!!!!! My friend is calling "SHOCKING THE PHONE" but not really shocking anything!! I am reluctant to share the method, but this site needs more people to actually HELP out others
Click to expand...
Click to collapse
Hey dude!
Would you kindly provide me the sulotion.
I would appreciate it.
nicknowsky said:
HA HA, me and my phone guy (well the guy who I bought my Hermes from) HAVE FOUND A FIX to get the phone outta Bootloader Mode and back into OS!! in my case WM6!! I have to do it 1 more time to fully confirm the method!!!!!!!! My friend is calling "SHOCKING THE PHONE" but not really shocking anything!! I am reluctant to share the method, but this site needs more people to actually HELP out others
Click to expand...
Click to collapse
Mmm... do i understand correctly your post? Are you hesitating to help others because your method is risky, or because you express some exasperation about people on this site? In this case, do not forget that all people here are exchanging ideas, questions etc on a totally free base without any obligation. In the limits of there knowledge. Encountering a problem after flashing a device is the only responsability of the user. We just try to help. But i prefer to believe that you found a method, still risky, that you need still to test
That said, it seems that there are an increasing number of hermes encountering a problem with the radio part. It seems that stopping a flash at 11% is a symptom of that. See some consolidation of those problems here: http://forum.xda-developers.com/showthread.php?t=349461
I hope you will find a solution for your problem and moreover i hope that none of you bought a hermes second hand with an already radio part problem. If so try always to get your money back...
I AM trying to confirm my method BEFORE i share it, because it might work on mine, and I dont wanna screw anyones hermes up more
nicknowsky said:
I AM trying to confirm my method BEFORE i share it, because it might work on mine, and I dont wanna screw anyones hermes up more
Click to expand...
Click to collapse
Why don't you answer my PMs????
Please tell me your sulotion and let me try that if you have any
Hi, I`m having some serious issues when trying to flash my HERMES. As far as I can tell, it is SIM Unlocked, but not sure if it`s CID unlocked. it`s SPL-1.06, and I can't seem to get it to install HARDSPL. I have tried, and tried and tried and tried. I've tried flashing VIA SD-CARD, but it just says "LOADING" and displays a number at the top, then goes back to the bootloader screen.
When I am flashing via the wizard, it'll go into the bootloader screen, and the wizard will fail saying it cannot connect "CONNECTION ERROR"...
I am at my wits ends, and cannot figure this out for the life of me. I have had 3 TYTN's now, and this one has gotten the better of me. I was able to flash both of my other TYTN's, but unfortunately I got the WSD, and cannot repair them, they are both beyond my technical knowledge of repairs...
PLEASE PLEASE PLEASE PLEASE PLEASE help....
Trying so hard to get this done...
Copied the .nbh (ren to hermimg.nbh) to my SDCARD and reset into bootloader, as I said, it just came up "LOADING" then back to bootloader....
I'd rip my hair out if I had any..
any help would be appreciated..
***UPDATE - I don't know what the hell happened, but suddenly, this bugger is letting me flash VIA SD. It's a damned miracle!
Just out of the blue, it asked me to flash via SD in the bootloader. Thank goodness! After 3 hours, I finally got it working..
Cheers all!
if you need more info, just ask, I will provide all I can....
need help ,during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
IPL 1.01
SPL 2.03
my device freezed at loading screen .
Now ,when i tried to rom upgrade in bootloader mode , using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
Edit/Delete Message
TVincent0621 said:
need help ,during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
IPL 1.01
SPL 2.03
my device freezed at loading screen .
Now ,when i tried to rom upgrade in bootloader mode , using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
Edit/Delete Message
Click to expand...
Click to collapse
Okay, when you're in the "bootloader" method, have you renamed the file that you're trying to flash "HERMIMG.NBH".
also, try to use the "stripped" AT&T ROM first, see if that'll help correct the issue.
Did you flash that first before you attempted to flash a different ROM on your Hermes? I've read in many different posts that it is highly suggested to flash that first then flash your ROM to your Hermes.
Should always flash via SD-Card, not recommending flashing via USB Wizard.
Try the "stripped" rom first, on a formatted (FAT32) microSD card, and see if that helps.
Cheers
i have download the "stripped" AT&T ROM ,it also the same ,when using USB method ,it stuck at 1% and my devide reboot .
when using SD card method ,it show (loading ...) about 2 second ,then it will back to tri-color mode there .
TVincent0621 said:
i have download the "stripped" AT&T ROM ,it also the same ,when using USB method ,it stuck at 1% and my devide reboot .
when using SD card method ,it show (loading ...) about 2 second ,then it will back to tri-color mode there .
Click to expand...
Click to collapse
I had that exact same problem.
I noticed that I hadn't named the file properly.
It's HERMIMG.NBH I kept putting in HERMING.NBH. It's kind of funny, but it's an easy mistake. When you boot with the "HERMIMG.NBH" it should flash. I used the HARDSPL V7, which can be downloaded at http://forum.xda-developers.com/showthread.php?t=296722, which is a "sticky" for this forum. Try flashing that one. Also, double check your .nbh file, make sure it's HERM IMG not HERM ING
That was the problem I was having too, it would just show "LOADING" and a bunch of numbers then drop to the bootloader... Then all of a sudden... "POOF" it worked, after I double checked the file and noticed my spelling error.
Now, if you have that fixed and still getting the error, it might be something else. I'm not sure how to exactly fix that, but as I said, mine was just a minor spelling error.. The exact spelling that I have, don't know if it is case sensitive, is "HERMIMG.nbh"
if it is case sensitive, that could also be a minor issue.
try it, if it works, then bingo, you're back in business, if not, then I'm not sure how else to fix it.
Cheers!
>.< ,now i type correct word "HERMIMG" ,it shown loading ... and (00068002) on the top of loading ... ,now it ,have better improvement ,it show loading ... for about 5 second only jump back to tri-color there ,izit this is the normal procedure ?
TVincent0621 said:
>.< ,now i type correct word "HERMIMG" ,it shown loading ... and (00068002) on the top of loading ... ,now it ,have better improvement ,it show loading ... for about 5 second only jump back to tri-color there ,izit this is the normal procedure ?
Click to expand...
Click to collapse
Okay, we're getting there. But still a long way off from it working as it should.
Okay, do you know if your phone is HARDSPL?
If you haven't already HARDSPL your phone, you should download that and try to flash that onto your phone.
Also sounds like it isn't SUPERCID. You'll have to CID unlock your phone, which is a good possibility as to why it isn't accepting other ROMS.
If your phone responds to the flash wizard when you download a ROM then get the SUPERCID and try to flash that one first, then move on to the HARDSPL.
For the SUPERCID, and my previous post has the HARDSPL.
At least the situation is improving, and your phone is starting to respond.
We'll get it working!
The HARDSPL you have to follow most of the "manual" installation instructions, and copy, then rename the "HermesUnlocker_v3a.nbh" file.
Try to flash that file, and we'll see if we can get it going.
Cheers
i think my phone not yet HARDSPL ,can you guide me to do this ?
i search the web ,it show me to here "http://forum.xda-developers.com/showthread.php?t=296722" izit correct ?
and also superCiD:
1. Unrar RUU_HERM_Unlock_v3a.exe
2. Unrar RUU_Inside.exe
3. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer
or format it from your computer using a card reader (in some cases format doesn't work).
4. Rename HermesUnlocker_v3a.nbh to HERMIMG.nbh and copy it to the FAT32 formatted microSD card.
5. Insert microSD card on your phone
6. Transfer SSPL/SSPL-HERM.exe to your phone and run it
7. Confirm flashing on screen by pressing the power button.
how i wana do the step 6 ,my phone is stuck now ,i cant log in at all >< ,but i try step 1-5 ,it also shown the 00068002
TVincent0621 said:
i think my phone not yet HARDSPL ,can you guide me to do this ?
i search the web ,it show me to here "http://forum.xda-developers.com/showthread.php?t=296722" izit correct ?
and also superCiD:
1. Unrar RUU_HERM_Unlock_v3a.exe
2. Unrar RUU_Inside.exe
3. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer
or format it from your computer using a card reader (in some cases format doesn't work).
4. Rename HermesUnlocker_v3a.nbh to HERMIMG.nbh and copy it to the FAT32 formatted microSD card.
5. Insert microSD card on your phone
6. Transfer SSPL/SSPL-HERM.exe to your phone and run it
7. Confirm flashing on screen by pressing the power button.
how i wana do the step 6 ,my phone is stuck now ,i cant log in at all >< ,but i try step 1-5 ,it also shown the 00068002
Click to expand...
Click to collapse
Attached is the HARDSPL file, already named "HERMIMG.nbh, which you just need to copy onto your SD-CARD.
When those are successful you will be able to flash any rom you want (provided it is as Hermes ROM)....
But as of right now, your phone is NOT bricked. It just currently has no ROM on it.
Have you tried to HARD-RESET your phone?
That's the two soft keys at the bottom of the phone, above the SEND and about the END keys.
Press and hold BOTH of those, then press the "RESET" button on the bottom of the phone. That'll hard-reset the phone.
I'm not saying to do that, just asking if you've tried that option yet.
Good luck, let me know how it's going.
Cheers!
my problem has solve now ,i try to install original rom for the phone ,it work ^^ ,thank for your help ,nice to meet you my friend from oversea .
Now i afraid to change any new rom >.<,can you guide me the best way to upgrade the rom ?so that i wont face the same problem and also brick my phone .
TVincent0621 said:
my problem has solve now ,i try to install original rom for the phone ,it work ^^ ,thank for your help ,nice to meet you my friend from oversea .
Now i afraid to change any new rom >.<,can you guide me the best way to upgrade the rom ?so that i wont face the same problem and also brick my phone .
Click to expand...
Click to collapse
Glad the problem was solved, and very happy to help!
Absolutely I can.
First thing is first, we have to SUPERCID unlock your phone, and we have to HARDSPL your phone.
Run the HARDSPL first, because the wizard will actually temporarily superCID your phone, so that you can install the HARDSPL, which will help prevent you from ever bricking your phone.
with your phone plugged in for activesync, you have to run the "autounlocker.bat" file in the SUPERCID. What this will do is make your phone accept other custom ROMS, whether it is from another carrier, or one of the ROMS that someone has developed on here.
After this, I would highly suggest, that if you ever flash your phone again with another ROM, do it the "SD-CARD" way. I'd only use the wizard to flash the HARDSPL and the SUPERCID.
Let me know how it goes.
Cheers!
Hehe ,My friend ,i had flash my phone with WM6.5 rom ,my device was Dopod838pro ,it is old device ,for my opinion WM6.5 not so suitable for my device ,but WM6.5 look amazing >.<
heh! Nice! Well sounds like your phone is now back amongst the living! That's good news! Hope you have many years of enjoyment with your phone!
Glad to have been of help for you!
Cheers
heh! Nice! Well sounds like your phone is now back amongst the living! That's good news! Hope you have many years of enjoyment with your phone!
Glad to have been of help for you!
Cheers
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
TVincent0621 said:
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
Click to expand...
Click to collapse
Unfortunately, no, I don't. You'd have to get a Vanilla, or a "lite/ultralite" rom. That's about the best I can suggest, unfortunately with the hermes, it does have a smaller ROM size, and limited RAM compared to the new, more up-to-date modern phones, like the 8925(Kaiser), or the new Tilt 2..
Cheers
TVincent0621 said:
Do you have any must have application suggest me to install it ?
the memory for this new rom is low ,it decrease so fast ,with HTC clean ram i use ,it also the same ,it just save less then 1MB of ram ><
Click to expand...
Click to collapse
Unfortunately, no, I don't. You'd have to get a Vanilla, or a "lite/ultralite" rom. That's about the best I can suggest, unfortunately with the hermes, it does have a smaller ROM size, and limited RAM compared to the new, more up-to-date modern phones, like the 8925(Kaiser), or the new Tilt 2..
Cheers
use the [Easy Hard-Spl v7 beta v0.1] by qwasde2
it,s really usefull i tryed it,s by me
it,s for win XP and vista and se7en users
i,am not joking here is the link
http://forum.xda-developers.com/showthread.php?p=5136858#post5136858
Hope you dont mind me reviving this thread as I also need your help
I tried flashing the MrDSL's WM6.5 ROM to my Hermes. Of course I followed the direction, I have Hard SPL (ever since Schaps rom) and stripped ATT flashed first.
However when I started flashing this rom, when I reached about 5% on the progress bar, I keep on getting Error. I followed the Recovery Steps and luckily I get the Tri-color mode and the process says Recovery successful. I then proceeded with the flashing but still getting errors, then recovery, then continue, then error again. Its been 10th try now.
Finally I canceled the update but I can only get the tri-color screen. Tried to Softreset as well as Hardreset but no go....my screen only gives me the Tri-color mode.
Any advice please....
thank you very much...
EDIT.....
problem solved sorry for that post.
what I did was:
1. flashed again the stripped ATT ROM....success!
2. flashed again MrDSL's WM6.5 titanium ROM (titanium)....success!
Dopod 838 Pro working again!
thanks again!!!
Bootloader shows but phone won't flash
Hey everyone,
I'm not new to
flashing my Hermes.
I'm just having an
issue I've never ran
into and can't figure
out. I would
appreciate some
assistance.
The strangest thing
is happening to me
while attempting to
flash from my
storage card. I put
the phone in
bootloader mode
and it takes
(IPL-1.04 /
SPL-2.10.olipro).
Then on the bottom
Serial shows and it
never goes to the
next step and ask
me do I want to
flash the new image.
I put the att original
on the 2gb storage
card over and over
and over and
renamed it
HERMIMG.nbh over
and over and over
and just am
flabbergasted. The
phone is not bricked,
it just refuses to
flash again.
Does anyone here
have any solutions
or suggestions?
PS - I have
formatted the card
to fat32 and I have
checked it for errors.
The HERMIMG.nbh
file is on the root of
the storage card.
Hello!
It's insane, here is the description.
The android booted up just in safe mode.
The winmo had faults, so I've decided to change the whole system, with task 29.
At first I've changed my radio to the 2_12_50_02_2 version.
Than I've started the task29, the one what do not needs the radio.
Thats all I've done, and now I cannot reach the boot loader, or anything else.
The vol up and start trick is not working.
Please give me a solution, I need this phone working, I need a solution, and I appreciate every tip.
Thank You in advance!!!!
its volume down, not up.
same problem for me here
i did task29 and it was all fine, 100% reached and then the HD2 did a reboot, stopping at the black screen with the white HTC logo.
then as always i removed the battery and put it in again, holding vol down und clicking power-up once.
nothing happend... the phone vibrated once and got back to the HTC logo.
NO bootloader!
please do not tell me i'm too dumb to enter bootloader, i've been flashing custom roms for 6 months now!
my latest rom was Goatrip 6.0 and HSLP is 2.08
yesterday when goa6 was still "alive" the volume-down button worked fine, so the problem cant be some dust or dirt beneath the buttons.
edit: i've also tried flashing via SD card (clean FAT32 formatted 2gb card) the original stock rom 3.14 and a custom rom,
none of them is working either
every single hint of how i could solve this issue would be great!
hope to here from u guys
Remove the SD card and try again to go into BootLoader mode.
i have tried all methods and variations but i cant enter bootloader...
now i have found this thread:
--eeeeek cant post links --
its referring to the TP2 but i thought i would give it a try!
i've done this sketchy voldown+power+usbcable+batteryplugin thing but no result, even after 10 attempts :-(
Since you removed the battery, are all the pins straight?
those 5 (2 1 2) pins are in good shape
i cant post a link yet, ill send it to u via PM
posting links enabled:
http://forum.ppcgeeks.com/htc-touch-pro-2/122134-task29-didnt-complete-cant-enter-bootloader.html
i got it!
my stepfather owns a HD2, too.
i plug mine into his docking station while i was on the phone with htc support... just because i was bored waiting in the queue.
after the phone call i tried once again to enter bootloader e voila => boooom 3 colour screen!
i dont know whats the reason for, but i flashed my custom rom as fast as i could and it works fine.
but even now i cant enter bootloader properly...for 10 times trying 2 times actually work!
in the WM Os its no problem, Vol-Down functionality is 100%
cant explain that to me,
i think u need some luck to get this issue solved
___EDIT___
now with my customrom i could easily enter the bootloader via software command
and therefore i downgraded HSPL to stock spl1.42.000.
after this i flashed 2.08.hspl again and NOW my bootloader is working as intended!
u see, once u can get into bootloader again, all your problems can be fixed.
without him, you're f*cked
greetings
Hey all, I am having trouble booting anything onto my HD2 everytime i boot the phone i get stuck on the (tri colour screen) "Hardspl" i think..
I am able to install original HTC roms and custom roms via USB and Serial but after i install them and it says installation complete when the phone restarts it just gets stuck on the "Hardspl" screen again??
Any help is appreciated thanks
Here are some images to help
http://img29.imageshack.us/g/dsc0007riq.jpg/
(UPDATED)
How do i remove hspl ive tried installing an offical rom from the SD card but i still boot into this screen ????
Try this........
Power off the phone (make sure your battery is over 50%)
Turn on while holding the vol. down button.
You should be at bootloader (three colour screen)
If you have HSPL installed you should see "cotulla" and "HSPL" on the bootloader somewhere.
If youve been flashing official roms though this may have uninstalled HSPL.
I couldnt get the screenshots you linked to...
You can attach image files using the "manage attachments" button down under the text entry area.. (i think)
Id suggest trying to flash a stock/official rom just now until you get up and running.
With the phone at bootloader you should see the word "serial" at the bottom of the screen....
Connect via USB and wait for "serial" to change to "USB", this could take a few minutes.......
When you see "usb" flash the ROM from your pc......
You should make sure that you have the correct ROM for your phone, go to the HTC site and pump in your serial number.
If you still have problems after this then post back here with any error messages you might get...
Hope that helps.....
Thanks for the reply, for the link you need to add (http ://) sorry i should have mentioned that
but i just finished doing what you told be and it finished installing. it had the HTC logo on phone with loading bar as on PC screen no errors :S but im still stuck on the tri colour screen
I originally had android booted onto this mobile but the 3G was not working so i tried installing the HTC wm 6.5 rom that I downloaded from the HTC website but it would not get out of the tri colour screen after i installed it.
So i though it may have been the hardspl its self so i updated the SLP from 2.05 to the 3.03 one im currently on but it does the same thing
Hmm ok...
So the flash finished all the wasy to 100% and there were no error messages..
then the phone rebooted and went to bootloader (3 colours)...??
Restarting the phone just keeps returning you to bootloader??
Try turning off then back on while holding down both volume buttons and see what happens.
Which model of HD2 do you have and which ROM did you flash??
Yes thats correct.
When i turn the device on wile holding vol up-down i get a grey screen to
"This operation will delete all your personal data, and reset all settings to manufacturer default. press vol up to restore or press any other keys to cancel"
and im not sure what HTC HD2 i have..
Model: T8585 ?
I flashed the latest rom from the HTC website using the S/N
"RUU_Leo_S_HKCSL_WWE_3.14.831.3_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship"
Okay, get to that screen and press volume up to continue, this will perform a hard reset which is recommended after a flash, your device should then boot up, may take a few minutes as its the first time..........
ok, It finished in like less then 10sec but there was not skips did from 1% - 100% smoothly and says "Restore....Completed Press VolUp to boot"
So i pressed volume up and once again stuck on the tri colour screen
any more suggestions or is my phone dead?
Hmmm
Phones not bricked because 95% of the time if you can get to bootloader the problem can be fixed........
I have the feeling this is something obvious that Im not picking up on.
Chances are someone else will see this and point out the obvious but at the minute I cant think why it might be doing that......
You could try flashing the ROM from SD card.
Rename the file on your PC to "leoimg.nbh" and put it on a 2gb/4gb sd card, turn the phone off, put the card in, turn on and it should flash........
Like I said, i dont think your phone is dead, I think Im missing something obvious....
its weird because i can install roms, hardspl's and all that stuff it knows the phone is there and installs them but for some reason it never gets passes the hardspl stage.. on each boot.
it accually boots into the tri colour screen in a split second of turning the phone on
Its a longshot but is there any possibility that your volume down button is stuck in the pressed position.........
yeah i have installed off the SD card already. that took awhile but it says everything is ok and installsion has completed.
same problem though once i restart tri-coloured screen pops up.
Im afraid Im not sure about this one...........
I'll keep thinking and let you know if anything occurs to me.....
Im sure someone else will chip in at some point and point out the issue though.
alright no worries thanks for the help and time hopefully someone knows what the problem is.
Maybe if i uninstall the Hardspl? might totally wreck it and 100% brick my phone if it fails but I think its the only option ill have left soon
uninstalling hspl shouldnt cause any harm........
I didnt realise you had HSPL installed, I take it you instaled that after flashing the stock rom??
If you have HSPL installed......
Try to install a custom rom, ie an energy rom, just as an experiment........
dunno if youve seen the images yet conan, but unless its changed since, the OP has 3.03.0000
also, if he has magldr installed ( i didnt see it mentioned, but..) when you hard reset it takes just a few seconds, because it is only hard resetting magldr (at least thats my understanding, and would offer a reason why hard reset is so quick)
I suspect incorrect 3,14 flash, which didnt complete so its returning to bootloader,
so, OP, bootloader - hspl4 - 3.03.hspl - flash your 3.13 rom again, over usb.
ok thanks ill try that right now, also yes magldr was installed for android but i thought I got rid of it once i rebooted the offical HTC rom.
If this works im donating $20 to you right away no joke .. ive been trying to fix for 13hours straight
Australian icon said:
ok thanks ill try that right now, also yes magldr was installed for android but i thought I got rid of it once i rebooted the offical HTC rom.
Click to expand...
Click to collapse
sd card flash, right?
Step 1 of the flash is the spl gets overwritten by the one in the leoing.nbh rom (3.03.0000 in this case) and then the phone reboots, and starts to flash , , splashscreen (where magldr is), radio, rom.
BUT, the phone wont allow the flash to start because hspl is now gone, so it fails CID checks and stops, so doesn't remove magldr, radio, rom, nothing, it just stops. Further attempts at flashing fail because you teh user haven't notived the spl change, you assume the whole flash failed, and that hspl is still there.
You shouldnt be able to get that far normaly, it would fail before it even starts, on a stock spl, except that hspl was there, so the flash was allowed to begin.
Ok, so its on SPL-3.03.HSPL now then I installed the latest HTC offical rom with USB but still no go
also if it is resetting magldr how come it doesent load up like it used to after a reset