Can anybody show how to sync via bluetooth? Thank you.
You need to set up a sync relationship first (using the cable),
On your computer, go to the bluetooth settings. (I have a link in my task bar, but should be in Control Panel).
Go to the "COM Ports" tab.
Click add, and pick a number between 1 and 18 (ActiveSync won't work with comports above 18, not sure about device centre). And make it an incoming port.
In ActiveSync goto "connection settings" and check the box "allow connections to one of the following" and select the comm port you created earlier.
Next, in the "bluetooth settings" (this time in the 'devices' tab) add a connection, and set up the connection to your device (you will need a pin for this, "1111" will do_. On the devices screen, after the partnership has been created, there will be an "advanced" button (left softkey). Press it, and check the "ActiveSync" box.
Related
Hi.
I have already download the new w2k5 to my XDAII and now I can´t wyncronize it via USB with the new ActiveSync 4.0
I have tried via infrared and it works, but when i put my XDA II in the credle, and I try to do it via USB it doesn´t works... Any idea?¿
Thanks
are u sure the File/Connection settings/allow USB connection is checked??!!! :wink:....... otherwise,u cannot synchronise via USB...
RAGO :lol:
Yes, everything it´s ok
I don´t know what could it be... Maybe reinstalling activesync 4.0...
thanks 4 all.
The problem with the USB conection of my xda II and activesync 4.0 still kickin´...
I have read something abaut the same problem in another post? Or it´s just a dream?
Thanks.
It's kinda strange what's happening with u... :?
Now am not sure,but try the following:
*u must have service pack 2 installed(it's a prerequisite)
1-on ur mobile:go to active sync/menu/connections check synchronize all PCs using this connection,and in the window tab below choose USB.
2-try changing the USB port on ur PC.
3-try restarting ur PC,and ur mobile as well...
4-make sure the File/Connection settings/allow USB connection is checked
5-make sure ur cable is functionning well(try another device if u can,or another cradle if possible)
Good luck....
RAGO :lol:
I´m trying to synchronize in a IBM T21 Laptop... Maybe USB 2.0 not soported? Does anybody knows if ActiveSync 4.0 and wm2k5 only works with USB 2.0 ?
Many Thanks
spend some time today to make it work.
first check on device manager if under network adapters exist "windows mobile-based device" and is ok (not with ! sign),
then go to control panel at network and internet connection > network connection.if you have network card there will be one local area connection (or maybe much depend how many network cards have in pc).when conected pocketpc (wm2005) will create another local area conection,connect and disconect to see what number have ex. local area connection 2.right click properties then better tick on show icon on notification area to see what is about connection.go to advanced windows firewall >settings.at general tab turn off,at advanced tab unmark this area connection only,( I want to say to unmark local area connection 2 or what number have this connection between pocketpc and pc) leave marked other local area conection (if is present) to keep protect your pc from outside.press ok in that window,now you are back in properties page check at general tab >tcp/ip protocol > properties to be selected obtain an ip address automatically press ok ok again. now in pocketpc go to start > settings > connections > network cards here select connect to "work" and adapter remote-ndis host select "use server assigned ip address" ok ok again.dissconect and connect pocketpc to pc.look at taskbar right-down corner of monitor,near clock,you should see appear network connection icon.first time at every connection between two little monitor will be a red dot going from one to another,in this time computere search for dhcp server to receive ip address,in short time (4-5-6 seconds) link will be active icon will be clear not fading like previous and the two monitors will blink.if this is not happened check on control panel > Performance and Maintenance > Administrative Tools > services if dhcp client is started,if not start it manual and change startup type to automatic.if until now everything is ok disconnect pocket pc, dezinstall old version of active sync install version 4.0 build 4343 restart pc.after pc started up connect pocketpc to pc,it should work.if still not work dezinstall active sync and from control panel uninstall windows mobile-based device disconect pocketpc restart pc install active sync and connect pocketpc,in this way windows reinstall networ driver and now must work ok.
btw I forgot to tel to check at active sync allow usb connection.
good luck.
Thank you very much for everything gabiz_ro.
Ok, I´m going to tell you what I have realized trying to follow your instructions.
Firstable I don´t have that you call:"windows mobile-based device" Or I didn´t find it... I have looked at Lan or Internet connection.
Then, I have tried to find out the conection that you talk abaut that it must be created when I connect my PPC, but I didn´t find it too. I tried to find it conecting the XDA II via USB and via Infrareds (remember that via IRDA does works)
Finally I changed at my PPC what you say abaut remote ndis host, I saved it, and disconnected and connected again, but it didn´t appear anything at taskbar right-down corner of monitor...
I don´t know what to do... And I´m sure that the problem is hosted the new activesync 5.0 or in wm2k5, cause one hour ago, when I came back to w2003se, I synchronized the ppc correctly with the credle via USB...
I´m feeling very weird with it, cause when I put the PPC in the credle (with wm2k5 and actvesync 4.0) the normal sound of the PC when you connect something reconigzed, don´t sounds... what I hear is the double "tun tun" that sounds when you connect something not recognized.
Many thanks
wm2003 is identified by windows as usb device.
but wm2005 like a network connection.
first
right click on "my computer" > properties > hardware > device manager.expand network adapters,and here when conected pocketpc to usb you'll see "windows mobile-based device"
second
local area conection 2 (or other number,in raport with how many network cards are installed on pc) you''l find in start > control panel > network and internet conection > network connection.but appear only when xda is connected if xda is disconected that "local area connection" dissapear too,and xda must be identified and driver installed (windows mobile-based device show without any ! symbol in control panel).infrared connection will not work here.on that local area network who represent connexion between pc and xda right click > properties and mark show icon on notification area.....
if you hear other sound like you say,maybe xda is not identified or windows didn't install corect driver.take a look to see in control panel what is wrong.expand universal serial bus to see if ther is some unknow device or something wrong.
there is control panel print-screen and taskbar area prinscreen.
Ok!
I think that finally thanks to you we have discovered the problem...
I don´t have everything you talk abaut in the device list...
But what I have is this: Generic RNDIS (PROTOTYPE- Remembber to change id Vendor)
It is with the yellow alert icon.
But what could I do to put it right?
thanks
YEEEEEEEEEEES!
Problem FIXED!
That was the problem... It was not recognized, and with alert yellow icon... Thank you very much gabiz_ro, if you´ll didn´t helped me, now I would be changing back to w2003se
Thank you very much again
ok.
glad to can help.
Problem with sync on WM 5.0
Hi, All. Anyone HELP ME pls.
When I finished upgrade my device to WM2005, my Active Sync (4.0) not working, on USB mode.
Only it's working with Bluethooth.
And I saw on PC Device Manager -> Unknown Windows Mobile Device.(Generic RNDIS (PROTOTYPE--Remember to change idVendor)
How can I fix this Problem? :?:
re-install drivers for this device
Pleun,
Hoe installeer je de drivers opnieuw. Volgens mij heb ik die niet
Groetjes
Frenske :lol:
Yes, everything what you need to do, is to click on update drivers, and everything will be fixed
Best Regards
click Update!!!
Windows cannot find this driver...
But I fixed this problem, whereas after than my device is dead. (not working radio, calendar, bluetooth etc...)
Now WM2005 is not good working on XDA II.
try deleting the device, restart pc and have windows find it again.
prototype
Ive got the same problem, where can I get the drivers to fix this???
Thanks Peter
Drivers
IIve got my MDA PRO for afew days now.
I coudnt sync with active sync 4.
I did a rom update and de beta version of active sync 4.2
:lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol:
http://t-mobile.iris-global.com/mdas.html
This PDA is like the world in my hand.
Greetings pocket pc freaks
Just got a TomTom5 kit with Bluetooth GPS receiver from PDAMods.com.
Followed the instructions to set everything up, but TomTom still says "No GPS device!".
The XDA seems to connect via BT to the device OK, and the BT active light comes on on the receiver, so I think its maybe connection params.
The only step in setting up the receiver that I couldn't perform was changing the outbound COM port to port 8 in BT Settings as specified in the receiver manual.
I go into Bluetooth Settings.
Select the Services tab.
Select 'Serial Port'' as instructed.
Make sure Enable service is checked, authoriszation required isn't, and Authentication passkey required isn't.
Then I go into the Advanced options to set the ports and I can't edit them...
Any ideas? I need to use this this afternoon - in about and hour and 10 minutes, and have been struggling for 2 hours to get the thing to recognise the receiver...
I've already had to do a hard reset, and lost a load of other stuff off the device, because the Bluetooth setting seemed to get corrupted and i started getting a message about Bluetooth license having expired. That bit is OK now after the hard rest, but the receiver is still not recognised.
In the TomTom prefs I have gone into GPS status and hit the configure button. Selected 'Other Bluetooth GPS'., and hit the ''Bluetooth Serial Port 5" line (which is what the inbound COM port connection is set to).
According to Bluetooth settings my Inbound COM port is 5 and my outbound is 6. The receiver setups says these should be Inbound 5 and outbound 8.
Please please point me in the right direction.
Thanks,
FM
try using cable
In TomTom try using the Other NMEA cable device (or somthing similar) - select the com port and set the baud rate (mine uses 9600 but you may need to try a few settings). I also ensure that I connect the device in Bluetooth manager before starting TomTom.
Hope this helps.
Denver
TomTom 5. & BT GPS
Don't tell me you haven't used the "outbound" com port setting .
The inbound/outbound name is nothign to do with data flow, it's whi instigates the connection.... the XDA does, so it's an Outbound connection you need to use.
Try Com6 (or com 8 .... whatever it was)
Once again, xda-dv forums members are stars!
That sorted it..
9600 and selecting the inbound com port (i think it was that one) made the thing spring to life..
now i know where i am going..
cheers cgrillo,
FM
hi
try to make 38000 bps , and remeber to choose com6 on other cable select...
i try it and he cames like a ferrari....eheheh
cu
Is there a quick way to have TOM TOM connect to the GPS Mouse when TOM TOM is started? Currently I have to start blue tooth manager and connect to GPSlim236 manually.
Then run TOMTOM.
Also, in my blue tooth manager my blue device is listed as:
Holux GPSlim236: SPP Slave.
is SPP Slave correct?
same problem as above! but i lose the conecction after about 10 seconds! any ideas? ive searched the whole forum and this is the closest ive come
Hi, my xda mini s only has bluetoth COM ports on port 6 + 7, however tomtom5 only recognises the IR, serial, and COM ports 0, 2, 3, and 9. I have tried the 'Other cable...' thingy, changed the BAUD rate, and generally messed around with it. Any ideas?
btw, i use a globalstat BT-359 receiver (bluetooth)
Hi
I am new to this forum. I have an XDA trion and am attempting to set it up with a Nikkai (from Maplin) GPS reciever. All software has been installed, however the software doesn't seem to pick up the signal from the reciever.
Any suggestions?
Phill
What software are you trying to use it with?
Have you paired the device and set a serial port?
Have you configured the software to use the same serial port?
Tell us more...
I am using Tom Tom software.
I have been through the bluetooth connection wizzard and it offers a serial port connection, which has been selected.
On the GPS reciever, I had assumed it would connect automatically, how would I find out which port it needs to use on the device?
Phill
Need to do two things:
First with tomtom 5x or 6:
1. You need to pair your bluetooth device (this means adding the device to your bluetooth device list)
comm mgr > start bluetooth > bluetooth settings > add device > provide passcode for pairing > select serial port > done!
2. Now you need to add a outgoing port:
bluetooth settings > add port > select your paired device > add a port that is suitable (I use com port 09) > optionally check secure connection> done !
Turn bluetooth off !!! Tomtom usually controls bluetooth so it will turn on and off automatically.
Now start Tomtom choose preferences and go to GPS setting:
Select bluetooth GPS and then configure to use port (09 in my case) which you created. Then you should start seeing signals....
Hope this helps. Good-luck!
Hi There,
I have upgraded my Atom Life to WM6 (latest version from O2 site). Everything works well. But I have problems with syn via bluetooth and IrDA. Please see my problem below:
Before syn with bluetooth or IR, I can syn with USB well.
* For IrDA:
+ When I choose syn with IR from activesyn menu on Pocket PC it shows "Attention required" then I click on this it shows "Connection Not valid: cannot open the connection 'infrared port'. This connection does not exist or no longer support. Select a difference connection or try again"
+ I am sure that: IR in range and I can do this many time on WM5 as well as send and receive file between my Atom life and My Laptop.
* For Bluetooth:
+ When I choose syn with Bluetooth from activesyn menu on PPC it show "Cannot find an existing Bluetooth partnership with a PC that supports ActiveSyn Would you like to set up Partnership now?"
+ I am sure that: Bluetooth in rang and pair with my laptop, I can send and receive file between my Atom life and Laprop. I can syn via bluetooth with WM5 many times.
If anyboby know what are the problems and solutions for these please let me know. If you can point me some document that would be great.
Thanks in advance
I dont own Atom Life, however sounds like you havent got the COM Ports configured properly...with MS generic bt drivers add (Incoming connection) port (usually COM3 is selected by default) after adding the port go to Connection settings in Activesync and under (allow connection to one of the following) select COM3. Assuming you have already paired your device now go to bt connection settings in device and tap your PC name then tap refresh, wait until it discovers A/S, tick the box then add a com port on your device too. I usually select COM6 but I do not believe it matters. good luck if that doesnt work then you should ask O2.
PS...if you already have an existing partnership and its not syncing, then delete partnership from PC and device and start again.
Thanks for your information but I still not work. I did check carefully incoming connection port and I also configured allowing connect wireless on ActiveSync to connect this port. Every step, I think correctly because I configured and sync with WM5 in the day before I update WM6. I don't know why It happens when I upgrade to WM6 then I could not syn with Bluetooth and IrDA. Maybe, I should get help from O2 support centre.
I have an mpman mp824 tablet (same as Coby Kyros MID8125), preloaded with Android 2.3.3. I want to use a VPN, but when I go to the Settings - Wireless and Networks screen, there is no VPN setup item as I would expect. I'm not an expert, but I assume this may be because a) the VPN applet is there somewhere, but has not started, or b) it is not there for some reason.
Can anyone help, plus is there a way I can overcome this? I have tried the supplier, but they are not replying
Thanks in advance for any advice.
Try these steps. It will surely help you!
1-Tap the ‘Menu’ button on your smartphone to open the resulting window.
2-Open the ‘Wireless and Network Settings’ window as you enter the new window and tap the concerned icon.
3-You will notice the option for ‘VPN Settings‘ along with many other options depending on the interface of the respective android vpn phone.
4-After tapping the VPN settings option, you will get the choice to connect to one of the many protocols available. From these, choose ‘Add PPTP VPN’.
5-In the next window, you will be asked to set VPN Name, VPN Server, Enable encryption, and DNS search domains, depending on your handheld devices.
6-Provide VPN Name and other information accordingly, click OK to complete the VPN configuration.
7-Navigate back to the VPN listings window and tap the VPN network that you have created just now to establish the connection.
8-The connection will be notified by a key icon in the notification area of the smartphone.
9-To disconnect the VPN, all you need is to move to the location of the connection and tap the current VPN connection.