I have full flash HP6828, but still stop step 5,(Radio)
I have disconnect USB cable from PC, after 6828 still black screen, can not power on, and tried more method, but fail...
I have reference following manual, but I don't know JTAG point on my 6828,
who can help me?? will big thanks!!!!!
I've had a hung flash yesterday and here's how I resolved mine. Try it and see if it works for you.
1. Unplug from PC
2. restart PC
3. Take out phone battery
4. Wait for about 1-2 mins
5. Press and hold the two - buttons, and insert the battery (keep holding on to the buttons).
6. After 2-3 secs of placing back the battery, release the buttons.
7. At this time, if the phone dun boot, go to boat loader mode by press & hold the two - buttons again and poke the soft reset hole with the stylus
8. It should load to boat loader (white screen).
9. Connect to PC and run the HP rom v1.01.
knave said:
I've had a hung flash yesterday and here's how I resolved mine. Try it and see if it works for you.
1. Unplug from PC
2. restart PC
3. Take out phone battery
4. Wait for about 1-2 mins
5. Press and hold the two - buttons, and insert the battery (keep holding on to the buttons).
6. After 2-3 secs of placing back the battery, release the buttons.
7. At this time, if the phone dun boot, go to boat loader mode by press & hold the two - buttons again and poke the soft reset hole with the stylus
8. It should load to boat loader (white screen).
9. Connect to PC and run the HP rom v1.01.
Click to expand...
Click to collapse
Thank you very much, Now I have use JTAG method to fix, and if I were successful, I will post method share with everybody.
My 6828 is death
tangjunhu said:
Thank you very much, Now I have use JTAG method to fix, and if I were successful, I will post method share with everybody.
Click to expand...
Click to collapse
Could you please share you method. My HP6828 is dead too. There is still black screen and little vibrate (sound like operating fan) when press 2 "-" and reset.
I can't....
my device is HP Ipaq rw6828.... i have this problems twice, but ican solve it, now i had a same problem.... now i can't resolve it....
now my device still (dead) only LED indicator when i charge it...... i use anything method, but it's not work.... except JTAG, cz i can't use this method.... please, any other way except JTAG mode????????? many big thanks.................. if u have an opinion, email me, [email protected]
Related
Hi..I am unable to switch on my o2 xda stealth. This happened after the battery was fully exhusted. After that I fully charged the battery and now it is showing green. But still I cannot switch on this.
Anyone having the same experience and any solutions for this.
I tried to soft reset, and hard reset ( flag + ok + power button )..but none of these are working.
I would be really glad if someone helps me in this regard
Thanks
Sasank
xda repair
dear
u press three button togatther
1 (windows) 2 (ok) 3 (camera) button
and hold three button and press power button
if on select boot menu
now working
if not
u go to repair centre
Hi, i'd like to share a tips to HARD RESET O2 Stealth.
Days ago, i just bough a Stealth since my O2 IIi bricked (not by software/hardware accident), but my toddlers (daughter and son) likes to play my O2 IIi like a bumpy toy and throwed it to the wall and floor like a toy car/doll (i love my children more than my O2 IIi
its a new challenge for me to play with it, and started to browse xda-developers to find any upgrade (but unfortunately i still cant find it.. anyone found an OS upgrade for Stealth?)
And googled some tricks for this stealth, and for Hard Reset i found many different instructions (d**n), and its make me confuse and failed to hard reset this device.
then, just by trial error i found the right steps to hard reset my O2 Stealth.
I post it in my website, pls see the steps here www.padusi.com
pls use search feature in that website if the instruction page disappears from the main page.
Nice Try and Good Luck.
Very simple.
Hold down the power key until you see 'goodbye'.
Hold down windows & OK keys and the press power key....keep all three keys pressed down till you see 'welcome'.
Wait for the process to begin...don't panic if you see any clcourful screens.
Just follw the instructions like screen align etc ....and Voila..DONE.
bye.
kalya said:
Hold down the power key until you see 'goodbye'.
Hold down windows & OK keys and the press power key....keep all three keys pressed down till you see 'welcome'.
Wait for the process to begin...don't panic if you see any clcourful screens.
Just follw the instructions like screen align etc ....and Voila..DONE.
bye.
Click to expand...
Click to collapse
after some minutes white screen and nothing happend after that
If you cant hard reset then try the engineering mode
this is from yuc
The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engineering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
MY HP6815 IS DIED.
I was flashing with the good wm5 rom of NHOCBANME when the phone fell to the ground and has detached the battery!!!
My hp 6815 is off and doesn't turn on.
I tried to flash by ordinary mode but the phone is always off.
Only battery led is on if the phone is charging.
I think it is permanently damaged.
Can someone help me?
Test:
1 - Remove the batery...wait some secounds
2 - Put the batery back on it
3 - Press POWER
4 - Press RESET with stylus and press the 2 softkeys (the keys that are on top of the red and green buttons)
5 - The phone will enter flash mode
6 - Use software to re-flash or use SD card to do it(SD card option: card must be inside when you do this!)
The same thing happened to me... but i lifted the cell and there was no cover in the battery...
hope this helps...
Dead boot ?
Hello,
I have a same problem after flashing. No life in my 6815.
The LED used to blink orange when charging or usb connected but now it flashes orange-green. Does anyone know how i need to fix my boot with jtag or other fix?
Many thanks
A free TUROK game[Newest turok game out last year] for whoever helps me fix my bootup. Game is boxed, manual etc.
Thanks to GraeFNZ (and helloworld1)...This is the correct procedure:
" How to recover from semi-brick state:
1. Prepare a sd card with proper diskimg.nb0.
2. Pull out the batter for a few minutes.
3. Press and hold two "-" button and at the same time, put the battery in.
4. Wait a few second and release the button, then after a while, the device will be in bootloader mode. "
I have the same problem with 6815
Hello, I'm new to this forum I have problem with 6815, it's completly dead after trying to put wm 6.5 on it. I have tried to pull out battery, to put it back, to press "-" keys, to reset... but no succes. It's dead. Battery is fully charged. It's showing charging status when I conect it to the charger or USB PC port. Anyone, please help, doing it for a 2 days, my head and stomach are ruin...
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
lisah456 said:
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
Click to expand...
Click to collapse
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
after task29,when your device reboot
press botton "volume down" and will go in bootloader mode
now if you have your device stuck in white screen,remove battery cover
press red botton for softrest and press "Volume down" botton
bobsbbq said:
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
Click to expand...
Click to collapse
opsss..sorry bob
i have look now your post
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
kikimax said:
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
Click to expand...
Click to collapse
It won't because you're in the bootloader. Does it say USB at the bottom of the bootloader screen? As long as it says USB when the phone is plugged into your computer, flash a ROM and be happy
Hello!
And what if my hd2 not entering into the boot loader?
Thanx in advance
There is only one way to get into the bootloader.
Hold down volume and keep it down....
After that press the start button and your phone will boot up.
Now you will see the tree colored screen and you're in the bootloader.
Goodluck.
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
When you are in the bootloader screen, connect the phone to the computer /with the usb cable/ on the same bootloader screen it will change to USB - look at the bottom of the screen:
Open the folder - on your computer - where the ROM you want to flash is:
find the "RomUpdate*.exe" or "Install.exe" /if Android it will most likely say "DAF.exe" - run it as Administrator/ file and run it. Do as it says on the screen.
Do not disconnect the cable, do not touch the device. When it is finnished it will restart the device, disconnect the cable and enjoy your new OS.
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
use a <4gb or preferably <2gb sd card - class 4 or 2 with LEOIMG.nbh.
HSPL3_pkg after that - make sure .nbh (as above on sd root) is your stock and you CLEAN-reinstall bootloader.
ps:
Then hspl, then radio, then magldr, then windows 7, the hacks, then call M$= LIVE!
Hi guys i have a similar problem. After task 29 i went into the bootloader but can't install any rom whatsoever. I have SPL 3.03 on my devide, mind no not hard spl but SPL. Can anyone please help me solve this issue? I also tried to flash using sd card but it doesn't work. Please help me save my hd2. Thanks in advance.
tmo-hd2 wont go into bootloader after task29
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/show...count=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india..
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
gdsbalaji said:
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
Click to expand...
Click to collapse
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
lms1407 said:
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
Click to expand...
Click to collapse
I hvnt even instaled MGALDR yet....task29 and hd2 went into trouble...need to get to bootloader to save it now
Tried this as well before posting....hv a 2gb sd card>formatted to fat 32> stock rrunbh to leoimg.nbh > moved to root of sd card....but this can only work if bootloader can be initiated right? i cant get to boot loader
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
SOLVED {bootloader dont load}
checkout the solution for my problem here....might help u as well.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
______________________________
if you feel this helped...thank me
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
DeAdMaNwa said:
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
Click to expand...
Click to collapse
Man, did you say blackstone? You should go into Blackstone forum
To go into bootloader, turn off the phone. Press volume down button and the POWER ON button (not start button) at the same time until the screen appear. It works on both Leo and Black Stone
Goodluck
I was putting the new update on and Odin was doing its thing. it went black now I got the stupid screen of a phone pic a yellow triangle and a computer. I know my phone is hardware locked what can I do? I rooted it with the one click root but no rom was installed.
Do you have adb running? You do know there was a fix for hardware locked vibrants, right?
If you have adb running & your phone can be seen by your pc it might be possible to get the sbl file pushed in to flash. Not sure it would work this way but it might be worth a shot. Not to sure what commands you would need either.
All~G1 said:
Do you have adb running? You do know there was a fix for hardware locked vibrants, right?
If you have adb running & your phone can be seen by your pc it might be possible to get the sbl file pushed in to flash. Not sure it would work this way but it might be worth a shot. Not to sure what commands you would need either.
Click to expand...
Click to collapse
no computer does not see the phone. I used terminal to get into download mode.
What is the fix for the hardware lock?
nomadrider123 said:
no computer does not see the phone. I used terminal to get into download mode.
What is the fix for the hardware lock?
Click to expand...
Click to collapse
Do you not know how to search? God...
http://forum.xda-developers.com/showthread.php?t=804305
Master™ said:
Do you not know how to search? God...
http://forum.xda-developers.com/showthread.php?t=804305
Click to expand...
Click to collapse
I did search and search on hardware locked and bricked phones. My first post was about all I see is the phone, yellow triangle and the computer icons. I pulled the battery hold the volume up and down both put the battery in plugged in the usb cord and It goes right to the symbols of the phone, yellow triangle and the computer. Odin does not see my phone sorry but I have studied for hours how to root and do several things to my vibrant by myself. This has me stumped and looking for help.
nomadrider123 said:
I was putting the new update on and Odin was doing its thing. it went black now I got the stupid screen of a phone pic a yellow triangle and a computer. I know my phone is hardware locked what can I do? I rooted it with the one click root but no rom was installed.
Click to expand...
Click to collapse
I know my phone is hardware locked what can I do?
Nothing. The 3-button fix should have been applied prior to flashing anything! You need a new phone, unless somehow, magically, after searching these forums and trying the (at least) 20+ ways people claim to get into download mode work.
None have worked on mine.
im not asking if ODIN can see your phone. I was asking if ADB sees your phone...
Do you have ADB setup? if so, what happens when you type:
adb remount
If you do have adb setup and nothing happens then you are in the same boat as southplatte.
get the samsung captivate back to download mode
I have similar problem like that. When i use Odin3 one click flash the ROM. It stuck in the middle of flash. I take off the usb cable out ,try to reboot the phone. Oop .. the screen show the sign of the phone--- yellow triangle with exclamation sign in the middle---computer icon. Can do nothing with it, because the computer now can not connect with the phone.
In my case, I take the USB off the phone but still connect with the computer. Hold the volume button + power until the phone flash in black screen .This moment happen very quick ,it will go back to the unconnected sign again. When the screen turn black just release power button but still press volume button (otherwise it not working) hook the USB back in your phone right on that moment. The Phone go back to download mode. If not work try couple time ,important is timing right on the moment the flash to black screen .
Now ,you can use the odin3 flash the ROM again. It works for me ,and i try again same situation couple times. it really works.
hopefully, this will help for who got the same problem.
get the samsung captivate back to download mode
I have similar problem like that. When i use Odin3 one click flash the ROM. It stuck in the middle of flash. I take off the usb cable out ,try to reboot the phone. Oop .. the screen show the sign of the phone--- yellow triangle with exclamation sign in the middle---computer icon. Can do nothing with it, because the computer now can not connect with the phone.
In my case, I take the USB off the phone but still connect with the computer. Hold the volume button + power until the phone flash in black screen .This moment happen very quick ,it will go back to the unconnected sign again. When the screen turn black just release power button but still press volume button (otherwise it not working) hook the USB back in your phone right on that moment. The Phone go back to download mode. If not work try couple time ,important is timing right on the moment the flash to black screen .
Now ,you can use the odin3 flash the ROM again. It works for me ,and i try again same situation couple times. it really works.
hopefully, this will help for who got the same problem.
Thank you Tudo525..... That worked. Appreciate it. I have been stuck here for hours.
hello tudo
just can not do what you describe
when I have the phone-yellow exclam-computer picture, i press volume up and power, wait for 3-4 seconds, screen turns black and I release the power button and plug the usb?
JayJayaa said:
hello tudo
just can not do what you describe
when I have the phone-yellow exclam-computer picture, i press volume up and power, wait for 3-4 seconds, screen turns black and I release the power button and plug the usb?
Click to expand...
Click to collapse
No no! Hold vol up/down, not power...
Sent from my SGH-T959 using XDA App
Pull the battery, sim, memory card. Plug the usb. Hold volume up and down and while holding those two buttons put the battery back and it should get you in downloading.
Sent from my SGH-T959 using Tapatalk
Alex9090 said:
Pull the battery, sim, memory card. Plug the usb. Hold volume up and down and while holding those two buttons put the battery back and it should get you in downloading.
Sent from my SGH-T959 using Tapatalk
Click to expand...
Click to collapse
Omg Thank You! you just saved me 2hrs. Try this method if you guys get the triangle sign. It works!
Same issue...
Galaxy S 4g Tmobile - tried pulling all cards and battery and 3-button trick but to no avail. Never enters downloading mode. How can I tell if I'm fully bricked?
Dharra, youre in the wrong forum altogether
OP, try a jig. If that doesnt get you into download.mode, listen very carefully: youre ****ed.
Your only remaining options will be to send it to someone with a riff box (pm connexions2005 or go to mobiletechvideos.com) or do the unbrickable mod and run the unbricking app.
If you do fix your phone, do the hw lock fix right ****ing away!!
Sent from a cell tower to the XDA server to you.
tudo525 said:
I have similar problem like that. When i use Odin3 one click flash the ROM. It stuck in the middle of flash. I take off the usb cable out ,try to reboot the phone. Oop .. the screen show the sign of the phone--- yellow triangle with exclamation sign in the middle---computer icon. Can do nothing with it, because the computer now can not connect with the phone.
In my case, I take the USB off the phone but still connect with the computer. Hold the volume button + power until the phone flash in black screen .This moment happen very quick ,it will go back to the unconnected sign again. When the screen turn black just release power button but still press volume button (otherwise it not working) hook the USB back in your phone right on that moment. The Phone go back to download mode. If not work try couple time ,important is timing right on the moment the flash to black screen .
Now ,you can use the odin3 flash the ROM again. It works for me ,and i try again same situation couple times. it really works.
hopefully, this will help for who got the same problem.
Click to expand...
Click to collapse
Oh thank you thank you thank you Tudo525!!! You've saved my phone!! I was trying to upgrade my brand new Galaxy S2 HD LTE through Kies and it froze just like your problem. I did what you suggested and it worked perfectly!! Now I have my phone back!! Thank you!!!!!!!!!!!!!!!!!
The Same Happened I Did what u said with ODIN 3 ... but my phone Continuously restarts with in a minute interval ... Please Hep !!!
The PDA I used is CF-Root-XW_OXX_JV1-v1.3-BusyBox-1.17.1.tar.
Samsung Galaxy S ... 2.3.3 DDJV6
...
Seenu AndhraPradesh !
...
Thanks In Advance !
---------- Post added 11th February 2012 at 12:33 AM ---------- Previous post was 10th February 2012 at 11:56 PM ----------
The Restarts Too Stopped The Same I Did With CF-Root-XX_OXA_JVO-v3.2-CWM3RFS
Thanks Everyone ..!
Everyone Smiles When The Problem Comes To An End !!!
...
i9000 2.3.3 DDJV6
Seenu , AndhraPradesh
...
hello,
need help,
i also have display on my screen (cellphone)...(!)...(PC).
i tried the battery pull and plug in the usb and holding the vol- vol + buttons. still get the same thing. i also tried the holding the all 3 buttons (power) untill the screen went blank then release and plugged in the usb. no change.
i do get a chime on my windows xp that usb is connected but nothing shows up
also odin does shoes connected (comm XXX) but every time i try to re flash it just sits there on the "initialization"
what can i do?
What bootloader do you have? If GB press vol down and power together then plug in USB.
I've tried to install Cyanogenmod 9 on my Xperia Sola, I've unlocked bootloader official way, flashed kernel from this forum specialy made for sola (http://forum.xda-developers.com/showthread.php?p=28957468&postcount=412 This One), then boot.img of cyanogenmod 9 (FXP203) and...
When I want to do anything with phone, it just flashes my red led. I mean, that led is still on, when I press Power it just turn off. And when I try to connect my phone in fastboot mode, It don't react at all. Can I already throw it away through window?
I put it under a charger to see if it's just off energy, but i've noticed, that after a while, red led just turns off and that's all.
My god, help me or I'll be back on Nokia 3310
You've used the S kernel, not the Sola.
Download the FXP for Sola (Pepper) here;
http://forum.xda-developers.com/showthread.php?t=1876929
Flash boot.img via fastboot. To get in, hold vol up + power. Wait for 3 vibrations.
Hold vol up. Then jam the USB cable in. You should be in fastboot.
Alternatively, flash the stock sola ftf via flashboot.
Problem is, my phone does not react, it does not vibrate, just that red led is on or off. Nothing else. I've tried all of those combinations. I can't get to fastboot mode or anything else.
MelaPL said:
Problem is, my phone does not react, it does not vibrate, just that red led is on or off. Nothing else. I've tried all of those combinations. I can't get to fastboot mode or anything else.
Click to expand...
Click to collapse
Happened to me (I use Xperia GO). What I did is (as mentioned above) - Hold the power button and Volume Up button for sometime (it vibrates once after a few seconds, do not leave the buttons - continue to do so and after a few more seconds until 3 vibrations) and then the phone switches off. Now, hold the Volume Up button and plug in the USB cable - you'd be able to get in the fastboot mode. Flash a stock kernal and that should help.
If your phone is completely down (no charge at all), then above won't help. Plugin the charger and and wait for a few mins (before the red light goes off - you should now have a good knowledge on when the light goes off!) and try then try the above step. Once the 3 vibration comes, remove the charger and go ahead with the flash mode.
Hope this helps!
Thanks,
B.
Edit: By the way, I had my SIM Card and Memory card inserted in the phone when the phone was completely down without any charge. I don't know how, but it makes a difference with you try so (atleast in my case) with them.
If it does not vibrate, then it's a hard brick =\ You need the phone to be at least partially responsive to get into fastboot/flashboot.
Keep holding down. It should vibrate after 25 seconds or so.
Otherwise, you have to bring it to Sony and tell them their phone died on you.
Right now It dosen't even blink with Led. It's totaly down. I cant lock fbootloader, so I'm doomned. Hope that won't cost much...
Install Sony Update Service (SUS) and try to recover your phone from there.
Last shot here, but here's to hoping that the PC at least detects your phone.
Otherwise.... Yeah =\
If you unlocked your bootloader Pc companion will be useless for you cause it will not detect your phone,.,,
i think other way is to flash the stock ftf for you device using flashtool.... that wuld be the best shot for you...
please respond if this fix your problem
No, SUS will detect, but will refuse to flash. It will say "Phone has been modified".
Need to see whether it's a hard brick. If even SUS does not recognise, then bring it to Sony =\
None of the above works. It's just dead and sometimes flashes red light. PC Companion says that there's no phone connected. Hope I will be able to gain a varranty or I'll be on Nokia 3310. But I'm not verry cheerful about that...
Flashtool does not react when I plug in my phone in fastboot or flash.
Hey bro,
Its highly unlikely for hardbrick to happen to Sony phones by flashing a differnt Kernel when Flashtool is there Pretty sure that it ought to work, follow the steps below (Note that the order of usb cable connection is the most important thing as doing it wrong will not allow Flashtool to connect to the phone when its bricked ! )
First, try plugging it in to charger for a while to ensure that there's some charge. Follow up with the Vol and power Button to make sure its turned off. Then after that follow this procedure *exactly*
1) Prepare Flashtool and select the FTF. (Flashmode )
2) When flashtool asks yo to connect the phone, connect the USB cable to PC
3) Then, holding down ONLY the Vol Down button (No Power button, Note that ) connect the phone to the USB cable and in a few seconds, Flashtool will start flashing
I know you tried many variations but missing out on one or the other detail during your previous tries might have caused the lack of success Just try it and let us know what happens
Best of luck and hope you dont have to go to Nokia World !
Cheers
Nope, it's still not working. It just dosent detect phone. I'm pluging in, holding only volume key and I'm waiting 5 minutes - nothing happend.
Nokia 5530 for now, but come one...
Hi,
I am currently having the same problem (I have bricked my sola by flashing with fxp boot.img). After digging the internet I found out that you can start fastboot by:
1. holding all 3 buttons (power on, volume +, volume -)
2. the phone will vibrate
3. the phone will vibrate 3 times
4. release the buttons
5. hold the volume + button and plug in the cable
6. you should be in fastboot now (blue light on)
If fastboot does not work then do 1-4 3x. Good luck! Hopefully we will unbrick our phones
Br,
Wermesz
wermesz said:
Hi,
I am currently having the same problem (I have bricked my sola by flashing with fxp boot.img). After digging the internet I found out that you can start fastboot by:
1. holding all 3 buttons (power on, volume +, volume -)
2. the phone will vibrate
3. the phone will vibrate 3 times
4. release the buttons
5. hold the volume + button and plug in the cable
6. you should be in fastboot now (blue light on)
If fastboot does not work then do 1-4 3x. Good luck! Hopefully we will unbrick our phones
Br,
Wermesz
Click to expand...
Click to collapse
Lol things u get on the internet!!!
First there is no such key combination to start fastboot k so just dun break ur buttons in an attempt to start it ...
Steps 1,2&3 are steps to get ur device force restart and force shutdown and let me tell you one thing
step 1 is wrong it power button and volume + button. That's it first the phone will vibrate once for force restart and if u keep pressing it will bypass over to force shutdown which is indicated by 3 vibrations..
Sent from my Xperia Sola using xda premium
could work
I have a Xperia U and triying to port JB to it I briked two or three times.
I hold power botom and it vibrate and doesnt happen anything ok.?¿
The possible solution could be this(for my works)
Charge the phone like 1 hour for my doesnt charge with the animation but its for security.
With the nest steps you are going to lose all CWM and tweaks and apks but personal data still there.
You have two options:
Flash a new rom with flashtool, but when you pluged with volum - you hold it for allmost all process becose for my i conect to PC and its goes quikly so i cant do annything.
If the phone is not recognised by Flashtool:
You have to repair it with PC Companion or Bridge for Mac, and also the same hold volum - almost all process.
For my it works, tell my if for you works:cyclops::cyclops::cyclops:
Hi,
it worked !
after doing the steps I have posted earlier I managed to flash my xperia sola with the right boot.img (the one from fxp pepper) and install fxp via CWM. Should work for you too.
One tip: you have to remove the assert from fxp installation script.
Br,
Wermesz
@op, your battery is dead and isn't accepting any external charge. Try replacing your battery with a charged one. That is if sola supports user replaceable batteries.
Sent from my ST25i using xda app-developers app