Please help! Problem with G4 hard SPL on Wizard O2 miniS - G4

just to be straight to the point. I have a Wizard O2 mini S and have upgraded to hard SPL successfully and managed to use WM6 for a while. few days ago, My brother accidentally run an orriginal wizard rom upgrade pack (contained IPL/SPL) and now my device doesn't work and my PC couldnot detect this wizard device in any mode (normal boot mode or USB - bootloader mode). However it still can enter the 2 bellow modes...
2. At normal boot: just only display and stuck at bellow message/info
_ IPL 2.21.0001
_ SPL 2.21.olip
_ GSM 02.19.11
_ OS 6.1.0.0
1. Bootloader: tri-color trip and indicating in USB status with following info but also could not detect by PC too.
_ IPL 2.21.0001
_ SPL 2.21.olip
I have read some info in the forum saying that you will bricked it if you run a rom upgrade contain SPL/IPL on an Olip (hard SPL) device. So i think this is my case but i don't know if there is any expert or user have found a solution to work over this case at this state... or any useful suggestion from you all might help me!! I definitely don't want an expensive paperweight...
Any suggestion of you all will be very much gratefull.

lavituyen said:
just to be straight to the point. I have a Wizard O2 mini S and have upgraded to hard SPL successfully and managed to use WM6 for a while. few days ago, My brother accidentally run an orriginal wizard rom upgrade pack (contained IPL/SPL) and now my device doesn't work and my PC couldnot detect this wizard device in any mode (normal boot mode or USB - bootloader mode). However it still can enter the 2 bellow modes...
2. At normal boot: just only display and stuck at bellow message/info
_ IPL 2.21.0001
_ SPL 2.21.olip
_ GSM 02.19.11
_ OS 6.1.0.0
1. Bootloader: tri-color trip and indicating in USB status with following info but also could not detect by PC too.
_ IPL 2.21.0001
_ SPL 2.21.olip
I have read some info in the forum saying that you will bricked it if you run a rom upgrade contain SPL/IPL on an Olip (hard SPL) device. So i think this is my case but i don't know if there is any expert or user have found a solution to work over this case at this state... or any useful suggestion from you all might help me!! I definitely don't want an expensive paperweight...
Any suggestion of you all will be very much gratefull.
Click to expand...
Click to collapse
If it gets into Bootloaders(Tricolor) and detects usb,it means its connecting with the pc.Try to flash any wm6 rom and see if it boots up normal,coz a Bricked phone won't either Power On,charge or get into Bootloaders,you might be in luck there.

hi zabardast, thank you very much for your prompt reply... i will try to do as u say... As you said... the phone is still able to charge itself when i conect it to the USB... Hope it will work when i flash with a new rom...
Will keep u all updated with the process. Thanks again

Try the Love Rom if WM6 roms fail. The RUU is compatible with a G4

XL3N7 said:
Try the Love Rom if WM6 roms fail. The RUU is compatible with a G4
Click to expand...
Click to collapse
similar problem faced,i install ampv1 rom on my kjam & wrking well but i tried to ensure that battery is "some how" 100% as my phone wont boot....but now working well.
1stly it failed (and i lose my hope)
but
i was trying to buy nokia n95 but can get it so tried once again....
hey it works (i think that it worked becoz i took out batter for 2days and possibily date went back to 2006)
so u can try this.

As long as you can see the 3 color ( bootoader) there is still hope
you can fix it just have to have a little courage... anyway there is nothing to loose anymore its either claim it as it is ... brick( I am telling you it is not bricked... you can still see the 3 colors right?) or go on the flashing part... more excitement
flash wizard love first and choose any rom here I think every rom has its own advantages and disadvantages... with that said ... happy ROM hunting

Good news...Prolem Fix
Good news, I've managed to get my wizard fixed... and now I would like to share with you all how i do it...
1. get a rom without IPL/SPL/Extended rom . In my case i got a slim version of WM6.1 (Slim-v3.0a) from pdaviet http://pdaviet.com/showthread.php?t=24923.
2. You also need to pay attention at the RUUResource.dll file which newromupdateutility_wizard_noid.exe pack will need to run your upgrade (I get it by extracting from the original ship rom pack for your device). If you receive an error message when u run the wizard_noid saying that it can not detect the RUU dll then just rename the RUUResource.dll to whatever it say.
3. get your phone to boat loader-USB mode and upgrade it with newromupdateutility_wizard_noid.exe (but remember some other version might not work, in my case i tried with several as i have quite number versions of them). If you like u can get the one i used.
Note: If you fail in running the wizard (because the usb connection is lost even if you see the USB status on it), remove the battery of your device, place it back then get to bootloader-USB connection mode and run the process again.
4. when the process finish, make a hard reset.
special thanks to the owners of the lovely tools and the rom I used.

Related

G4 WM6 BRICKED! please help ASAP!!!!

I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
nstefanelli said:
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
Click to expand...
Click to collapse
Check your PM's
bwesty said:
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
Click to expand...
Click to collapse
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
jUST DO WHAT I SAY
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
samy.3660 said:
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
Click to expand...
Click to collapse
I cannot do that because the Carrier ROMs that I have aren't for G4, so they arent working. I have three different carrier ROMs for my phone.. and none of them work.
-Stefanelli-
nstefanelli said:
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
Click to expand...
Click to collapse
Check your email, I downloaded and zip works fine here.
i'm facing this problem right now , i will solve it with the original rom .
the problem started when i used shelltool to upgrade my G4 CID Locked to windows mobile 6 crossbow underground edition .
i will give it another try when i get my device alive again ,
any suggestions for the WM6 underground to make it work using shelltool on my wiza 200 ??
--------------------- Edit -----------------------
Finally i solved the problem and installed Crossbow WM6 underground edition .
all i did is to install the original rom from provider and then used shelltool to install WM6 .
i want to mention that my wiza200 is G4 and its CID Locked .
Huge thanx to mUn , you are da man
Mmm
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
lobiik said:
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
Click to expand...
Click to collapse
whats your device and is it G3 or G4 ?
try to do as i did and it worked for me , install the provider flash , then try shelltool to flash WM6 underground .
WBR
a-h-t1 said:
whats your device and is it G3 or G4 ?
Click to expand...
Click to collapse
Mine is G4, dunno if cid is locked or not. I've flashed it as I said with wizard love rom and working without problems. I've tried that again this morning, to flash from love rom, but the same. At 96% it hangs, error 302 Communication error, then starts recovery process, phone goes to bootloader mode. Then is possible to flash it with love rom again with no problem
g4
i have a g4 wizard using the shell tool i have chaged my rom on my phone sometimes 3 times a week just to test them out
the shell tool works if you cant download from the forum here is the link for it
http://rapidshare.com/files/17787647/ShellTool_bugfixed.zip
G4
yes, but when I run shelltool, and press get rom info, all fields states N/A
info from phone is:
ROM Version: 2.26.10.2 WWE
Radio: 2.25.11
ExtROM: 2.26.10.105
IPL/SPL: 2.17.0001
And anyway, dunno exactly which rom for WM6 I can put in (I've just 5.underground_edition_Crossbow_ROM.exe which stucks at 96% with 302 error)
well, I'm dumb, mislooked one stupid thing. Everything passed without errors, Windows Mobile 6 is up and running
happy to know that , the problem was installing rapi ha ??
WBR
No, not really, rapi and that second cab was in device, it was restarted, but I did a mistake - i didn't copied that desired rom into updater directory - that was why were all fields N/A... did that, flashed on first try, without problem
I had the same problem, orginal rom from the provider, and I can reflash it again.....
THX for the info......
ROM verion and link location
Hi lobiik,
which ROM did you use for your device, as you comments above:
"i didn't copied that desired rom into updater directory "
can you please point me to location where i can get the ROM, also proper steps to install the same.
Thanks,
Ajay
HELP!!!!!!!!
I tried flash my G3 with shelltools the program said it worked well i did hard reset then i turned it on it is stuck on 1st front screen bootloader mode is stuck i dont know what is is my device bricked
---------------------edit--------------------------
im a newbie

UnBrick the Bricked Hermes with "SPL 2.03 - IPL 1.04 - NO GSM - KITL Disabled"

UnBrick the Bricked Hermes with "SPL 2.03 - IPL 1.04 - NO GSM - KITL Disabled"
There are many people have this kind of brick but still no solution for it.
I want to ask the mods to make this thread sticky so if anyone find a sulotion for this type of brick would post it Here.
Summary :
IPL: 1.04
SPL: 2.03
CID: NO CID (Request timeout on mtty.exe)
NO GSM
KITL Disabled
I have tested all the possible sulotions available in the wiki but none of the could help me unbrick my hermes.
P.S. : Please just post your sulotions here NOT your comments like "you should superCID your device first", "It's your fault to use telstra wm6",....
Has anyone found a sulotion for this???
You Pm-ed me asking what to do and i pointed you in the correct direction so why have you started this thread?!
Hermes Unbricking Thread
and
Wiki page: How to unbrick your bricked hermes
EVERYTHING you need is there, you just have to read.
Maybe You do not read my Pm!
I have read all the wiki and thread concerning my problem several times!
The simple truth is that some phones are unrecoverable and have to be sent off for repair. Yours is one of these situations and I very much doubt that this will change. More and more of the pioneering technical guys will have updated their Hermes to another phone and the much admired POF has not been seen since he was accused of stealing...
The tacit feeling is that there is enough information and utilities to prevent people bricking their phones (i.e HardSPL and Update from MicroSD card) so if you do find yourself in this unfortunate position and can not recover your phone then you have to bite the bullet, and be better informed the next time.
POF accused of stealing !!!!????
What's that all about?
I dunno if I have a the same problem, but a similar issue, and trust me I am "PC guys, AMD fanboy, A+ tech:"whatever you wanna call i, I am expanding my horizons and I got into the mobile PC world. Trust me I am NOT Google lazy, i have read and read and read and researched and cross-checked and tried literally everything. I am stuck, I know what is wrong with my Hermes, I know where it messes up, and I DO see threads in other sites with 99.9% the same problem I have and I see NO soultion or anyone who knows or Really wants to help, I feel for Koorosh we need help, I have come to terms if have to send it away to repair. That bugs me I got it Literally 3 days ago, and ONLY used the OFFICAL AT&T WM6 Rom to upgrade
on my bootloader all I see is this........
IPL: 1.04
SPL: 2.03
I have too see in my display
IPL: 1.04
SPL: 2.03
when i can flash radio 1% and restart device!
try it
i also had the same problem.i have resolved using rom update through memory card.look for it in wike section.all the best.try it with original rom that came with the phone.
this will not work in this site again no solution for bricked spl2.03 cid locked
biswajitghosh said:
i also had the same problem.i have resolved using rom update through memory card.look for it in wike section.all the best.try it with original rom that came with the phone.
Click to expand...
Click to collapse
Do you know to read micro sd flash not work when device is not superCID!!!
I maybe have the same issue.
From the HTC ROM I flashed my device to Shannix Grass rom, a few days later I flashed to Satin Black rom, so far so good. After that I want to flash back to Shannix Grass and my deviced crashed. While booting he stuck at the HTC screen.
I tried to hard reset, flash another rom (stuck and reset at 1%), flash the bootloader (stuck and reset at 7%). After the failed ROM flashing I get error 270 image is corrupted.
In mtty I tried to format the NAND, and tried the erase command, nothing worked.
How can I diagnose the problem further. Is it possible to see why the ROM update failed or why the OS won't boot? I did some monitoring with USB monitor but I didn't get results where I get some conclusions of.
---
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
(My device is Herm200)
wow , i have the problem too. i almost live in phoneless .
.
SOLVED !!!!!!!! my phone now works
If your device became inoperable like mine, because i had a failed ROM upgrade,and the device failed to power up i have good news for ya.
MY DEVICE info is as below.
Problem:
Phone does not boot up, and looks like a red brick.
IPL: 1.04
SPL: 2.03
(it always gave an error 206 at 1% of any ROM update i tried)
Solution:
I downloaded the official WM6 ROM from the HTC's website below,
http://www.america.htc.com/support/8525/software-downloads.html
Then reset my device to the bootloader screen.
(holding the 'ok' button and the 'power' button and then using my stylus to push the 'reset' button close to the USB port.
i then disconnect the USB cable from my phone, and the display showed 'serial'.
i then ran the downloaded file, and waited till the collecting information from phone window came up, then i connected the usb cable back to the phone.
it connected, and VOALLA!!!... it started the update.
at least its better to have a working phone(without all the custom stuff), than none.
I hope this was not booring( with all the detail and all), but i hope it will help anyone out there who's device wont bootup.
wow , congraution!
i will take the method. but i wonder should i have to get the "connecting time" in the right point, or the computer can't find my phone??
( hope u know what i mean?)
Um.... i cant say for sure
weyun0513 said:
wow , congraution!
i will take the method. but i wonder should i have to get the "connecting time" in the right point, or the computer can't find my phone??
( hope u know what i mean?)
Click to expand...
Click to collapse
Well.. i can't say you should wait 1 or 2 seconds, but just plug it in as soon as you get that screen. i hope it works for you tooo.
what was ur exact situation beforeu can unbrick ur phone???
IPL?
SPL?
KITL??
NO GSM ERROR?
what was the rom that has bricked ur device??
where did it stuck during the brick phase?
is that 1st splash,2nd splash,...??
This method did not work for me!!!!!
Try the Official Cingular ROM
koorosh_bsboys said:
This method did not work for me!!!!!
Click to expand...
Click to collapse
My Hermes "red hot brick" happened when i tried upgrading to aCRCs_PHKv12r8, from a Schaps_WM6Pro_Hermes_4.31_WWE_Full ROM.
My device is a Cingulat 8525.
The upgrade went to the tricolor screen, and after 1% , my phone magically went off. I tried powering on, but it went to the tricolor screen again showing
IPL 1.04
SPL 2.03
and underneath showed "serial".
me too i'm having the same problem....any experts out there that could help us?

Need help stuck at tricolor screen

Hey guys I'm a newbie... I was playing around and trying to flash a new rom onto my wizard/8125. The program stopped responding on my PC so I had to restart it. Now my phone is stuck in the tricolor boot screen. It says USB is connected but activesync won't recognize it.
IPL. 2.21.0001
SPL 2.21.01ip
Please help me I just go the phone working yesterday..
The reason activesync won't recognize it is because the activesync program isn't installed on your device, provided the windows mobile can't start. At the boot screen, you can still flash the device. However, I wouldn't play around with flashing your 8125 unless you know what you're doing; there's a chance that you could turn your phone into a brick.
Try flashing it with the Wizard Love rom found here.
You might need the English Update Utility files found here.
Then, if your phone is CID locked, you can use the G4 SoftSPL from this post to flash it with the G4 safe rom of your choice. My 8125 would often freeze at 99% in the update process, but flashing first with Wizard Love would do the trick.
I got it. Thanks for you're help though. I just flashed it with a new ROM program and seemed to work just fine. Thanks again
I have exactly the same problem I am also stuck and I am also showing the IPL. 2.21.0001
SPL 2.21.01ip
How did you Supa solve your problem?
I reached this stage after sucessfully installing hardspl and CID_unlocking and then tried to upgade to WM6 and failed to do a hard reset instead remove battery ( I know very stupid )
MDA3 Blue Angel
MDA Artemis
MDA Touch
He All, I managed to resolve by reflashing using ROM 1.1 CID-locked edition by ppctuning.org by simply running it-
Thank you for allowing me to do a lot of reading fro this useful forum
stuck in tri color screen
im also having this tri color screen problem... and mine the screen says..
---------------------------------
| RUU |
|IPL 2.21.0001 |
| |
| |
|SPL 2.21.0001 |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| USB |
---------------------------------
thats all.. every time when it reaches 99% it goes stuck for 2 minutes
and says
ERROR [302] : UPDATE ERROR
The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the errors so you can continue the the update.
and done the recovery as the guided.
this has happend for 3 times...
help me ...
You have a G4, and its CID Locked. You'll need to flash the Wizard_Love rom - it will install sucessfully on G4 Cid Locked - and then cid unlock it, before trying to install any other ROM. You need to be carefull not to flash rom's with IPL/SPL information, that includes official ones from T-Mobile!
My ELF (Soft Black) is also stuck in the tri-color screen after trying to flash it.
IPL 1.15.0002
SPL 1.15.0000
Please HELP!!!!
First of all, thanks to all the uber-smart people in the forum that make new toys for my Wizard!
Rabbid, if yours is a Wizard G4, install the Wizard Love ROM as dferreira suggested. If you don't know, check sticky posts on how to ID your phone.
I had the same problem, stuck at the loader screen, because I forgot to soft-unlock my phone.
That's the last time I reflash my phone at 2 AM, after being up since 6AM the previous day
Wizard Love was useful for me!
I had the same problem (tricolor screen), but I flashed my Qtek A9100 and it came again! (I´m so happy)
the rom that I used was Wizard_Love_2.26.10.2.
I hope it be useful for all you, guys!
I have a question. If I was wrong flashed G4 Hard-SPL unlocked device, can I fix the problem using RUU? Usually, I used soft-SPL.
Thanks for the responses on this thread! lol
I used the Wizard love and I do have a g4 phone I checked a million times.
I used the process to Hardspl my T-mobile Wizard and when I turn the phone completely off and on it is the Love Wizard. I got the steps from the XDA Developers Wiki Site.
I wanted to use the Slim Edition of WM6.1 and I have downloaded the zip( or rar) but what do I need to do next. I thought I knew about the flash process because I had experience flashing with GBA and SP but apparently I know nothing.
What I originally did was run the hard-spl G4 program but when the screen popped up to install a ruu ( or the os i gussed) I closed out of it and instead opened the boot loader program that was located in the Slim Edition Folder. I lost connection to my g4 at the white screen...naturally panicked for 30 mins and then realized the soft reset button and did the manual boot loader screen. I then read this forum about the love wizard so just installed it out of fear to try the slim version again.
Also, the XDA Developer process says that the HardSPl process unlocks both SIM and CID is that incorrect? And do I need to be concerned with downloading Radios for my g4 model? Any help or flame would be appreciated at this point. Thanks.
All I want to do is use the T-mobile Wizard (g4) with WM6 or MW6.1 and for it to be unlocked.
Again, Thanks for your time
wafrea said:
Thanks for the responses on this thread! lol
I used the Wizard love and I do have a g4 phone I checked a million times.
I used the process to Hardspl my T-mobile Wizard and when I turn the phone completely off and on it is the Love Wizard. I got the steps from the XDA Developers Wiki Site.
I wanted to use the Slim Edition of WM6.1 and I have downloaded the zip( or rar) but what do I need to do next. I thought I knew about the flash process because I had experience flashing with GBA and SP but apparently I know nothing.
What I originally did was run the hard-spl G4 program but when the screen popped up to install a ruu ( or the os i gussed) I closed out of it and instead opened the boot loader program that was located in the Slim Edition Folder. I lost connection to my g4 at the white screen...naturally panicked for 30 mins and then realized the soft reset button and did the manual boot loader screen. I then read this forum about the love wizard so just installed it out of fear to try the slim version again.
Also, the XDA Developer process says that the HardSPl process unlocks both SIM and CID is that incorrect? And do I need to be concerned with downloading Radios for my g4 model? Any help or flame would be appreciated at this point. Thanks.
All I want to do is use the T-mobile Wizard (g4) with WM6 or MW6.1 and for it to be unlocked.
Again, Thanks for your time
Click to expand...
Click to collapse
Well,as you mentioned,its a G4 phone,it cannot be CID unlocked completely like a G3 device,however,it can be upgraded to wm6 with 'SoftSPL' or 'HardSPL',if you apply "hardSPL' it'll semi CID unlock the phone by flashing a patched IPL/SPL to the phone to trick it to think its CID unlocked temporarily,but it'll stay CID unlocked and "HardSPL' as long as you intentionally don't remove it and you can flash any wm6 or wm6.1 Rom on it. But always be warned that don't ever flash any Rom which have IPL/SPL included in it,it'll 'Brick' the phone.
Did you apply 'HardSPL' successfully ? what IPL/SPL... ? it displays at present.
Secondly,if you didn't have any signal quality or call missing problem with your present Radio Rom installed,then there's no need to upgrade.Some custom build wm6 or 6.1 Roms,do already include updated Radio Roms,which get flashed durinf Rom (OS) upgrade.
Thanks so much for responding.
I don't know what all happened to be honest. When I was using the Hardlsp G4 program after I got the white screen I thought I would cancel the rom that it wanted to install and install the Slim Edition. I was thinking that it was installing an OS and I wanted to substitute it for WM6.1 Slim edition I didn't know that I was cancelling out of the WM6 rom softspl . So to be honest I though I just Hardslp it but I didn't use the softslp which comes with the temporary CID unlock? Maybe that sounds right lol.
Regardless, Now I'm tring to figure out what to do obviously this phone works with T-mobile only and so I thought I could CID Unlock it and SIM unlock it with that program and now I'm thinking i'm screwed lol.
If I followed the HARDSLP directions again to the letter would I get the phone temerporarly CID & SIM unlocked so I can use it or have I messed it up to much? Oh, and the phone seems to be getting a signal although I can't call anyone but the bars are showing beside the indicator.
I did get an issue were when my phone went white it dissconected from activesync and so I had to manual get to the bootloader screen anyway.
Thanks zabardast_1
IPL/SLP 2.25.0001
GSM 2.25.11
OS 2.26.10.2
wafrea said:
Thanks so much for responding.
I don't know what all happened to be honest. When I was using the Hardlsp G4 program after I got the white screen I thought I would cancel the rom that it wanted to install and install the Slim Edition. I was thinking that it was installing an OS and I wanted to substitute it for WM6.1 Slim edition I didn't know that I was cancelling out of the WM6 rom softspl . So to be honest I though I just Hardslp it but I didn't use the softslp which comes with the temporary CID unlock? Maybe that sounds right lol.
Regardless, Now I'm tring to figure out what to do obviously this phone works with T-mobile only and so I thought I could CID Unlock it and SIM unlock it with that program and now I'm thinking i'm screwed lol.
If I followed the HARDSLP directions again to the letter would I get the phone temerporarly CID & SIM unlocked so I can use it or have I messed it up to much? Oh, and the phone seems to be getting a signal although I can't call anyone but the bars are showing beside the indicator.
I did get an issue were when my phone went white it dissconected from activesync and so I had to manual get to the bootloader screen anyway.
Thanks zabardast_1
IPL/SLP 2.25.0001
GSM 2.25.11
OS 2.26.10.2
Click to expand...
Click to collapse
Well, with your present IPL/SPL 2.25.0001,its not HardSPL,as you say it didn't complete and you closed it,therefore,its still with its original official bootloaders (IPL/SPL),no harm is done yet.
Now,if you wish to upgrade the phone to wm6,either you can do it with SoftSPL, which'll just temporarily trick the phone into CID unlock and flash the rom,but it'll revert back to CID locked status after the reboot of the phone and if you wish to replace the rom,you'll again have to apply SoftSPL again.Every time you want to change roms,you'll have to apply SoftSPL,but if you apply HardSPL once,it'll remain HardSPL and temporarily tricked into CID unlocked status till you don't remove it.You don't have to apply HardSPL again and again to flash roms,its possible to flash roms easily.but never flash a rom which contains IPL/SPL in it even the official Rom in HardSPL status.If ever you wish to revert back to official rom,first remove the HardSPL and flash the official Bootloaders (IPL/SPL) and then flash the official Rom.
Ahh Thanks a Million.
Zabardast_1. I know it sucks explaining that stuff a million times but it really helped me.
So, If I was wanting to get the Slim Edition WM6.1 I could just
Run HardSLP Program and complete the stepes provided
Then hook the phone up to the computer while its in windows os and then click the bootloader app for Slim Edition? Thus Installing Slim Edition
Then use the the lolwoz03 program to unlock my sim?
Or would the last step not be needed because of hardslp?
I do have Love Wizard on here so when I start the phone up those isp/lsp is what i got.
I think thats the last of my questions and then i'll leave you all alone lol
wafrea said:
Ahh Thanks a Million.
Zabardast_1. I know it sucks explaining that stuff a million times but it really helped me.
So, If I was wanting to get the Slim Edition WM6.1 I could just
Run HardSLP Program and complete the stepes provided
Then hook the phone up to the computer while its in windows os and then click the bootloader app for Slim Edition? Thus Installing Slim Edition
Then use the the lolwoz03 program to unlock my sim?
Or would the last step not be needed because of hardslp?
I think thats the last of my questions and then i'll leave you all alone lol
Click to expand...
Click to collapse
Yup! First apply 'HardSPL' correctly,read the HardSPL thread carefully understand the method and do it correctly and let it complete,the screen will certainly go white,don't be afraid,its the essential part, it'll only take a minute or so,if it doesn't go white,then consider something is not correct ,after successful application of HardSPL,the phone will reboot and IPL will be 2.21.0001 and the SPL is 2.21.olip,it confirms the successful application of HardSPL.Now its ready to flash any wm6 or 6.1 rom,just hook up the phone and run the RUU in the rom,it'll start to upgrade
Well,regarding SIM unlock with lokiwiz03,you shud do it before HardSPL its much recommended.HardSPL will only flash the patched IPL/SPL which let your device think it has SuperCID (aka CID unlocked) but doesn't SIM unlock,for SIM unlock you have to use lokiwiz03 and generate a SIM unlocking code which you'll insert when using another SIM.
Well, Thanks again
All I know is when I run Lokiwiz it says it can't copy files and it might be inuse. So if there is a better way of unlocking or a way of unlocking the sim after i do the hardslp i'm up for it haha whatever works the best. I think it says it can't find the C:/windows/itsutils.dll and then it says it can't save a certian bat file because it doesn't exsit.
Okay I fixed it by copying the files Cert_SPCS and EnableRapi to folder Lokiwiz03 was in on my computer.
Well, I ran the SlimEditon romupdate utility and it took my phone to tri color screen then activesync discconected and it says it can't connect to my phone now. So did I click on the wrong program?
Thanks a million + Zar
I read something like If I take the .nbf file and transfer it into the muns ruu folder and run muns ruu that it should fix it but it says something about an aku and far when i start the program so I'm hesitent. Also I'm stuck in the Bootloader screen? Should I use the wizard love rom again and then when it finishes use the slimedition with muns ruu?
Well I did that from the bootloader screen (tricolor Screen) and slimedition works the only thing that sucks is that it still shows the wizard love pic when displaying my ipl slp and gsm info...
wafrea said:
Well, Thanks again
All I know is when I run Lokiwiz it says it can't copy files and it might be inuse. So if there is a better way of unlocking or a way of unlocking the sim after i do the hardslp i'm up for it haha whatever works the best. I think it says it can't find the C:/windows/itsutils.dll and then it says it can't save a certian bat file because it doesn't exsit.
Okay I fixed it by copying the files Cert_SPCS and EnableRapi to folder Lokiwiz03 was in on my computer.
Well, I ran the SlimEditon romupdate utility and it took my phone to tri color screen then activesync discconected and it says it can't connect to my phone now. So did I click on the wrong program?
Thanks a million + Zar
I read something like If I take the .nbf file and transfer it into the muns ruu folder and run muns ruu that it should fix it but it says something about an aku and far when i start the program so I'm hesitent. Also I'm stuck in the Bootloader screen? Should I use the wizard love rom again and then when it finishes use the slimedition with muns ruu?
Well I did that from the bootloader screen (tricolor Screen) and slimedition works the only thing that sucks is that it still shows the wizard love pic when displaying my ipl slp and gsm info...
Click to expand...
Click to collapse
Your phone is still running wizard_love_rom,it didn't upgrade to slimEdition,perhaps its still not correctly with HardSPL patched IPL/SPL,did you get it HardSPL ?
Well, everything else works fine. I think I soft flashed my phone back when I messed up and so it reset the loader screen with the ipl spl info and then when I hard Slp over top of it the hardslp just didn't remove the screen. It says all the information that it should it just has that love picture on it that is kinda emberresing but I'll live with it to have a working phone and not a shinny brick.
Thanks for everything again and again Zar, Unless you can tell me how to show the battery life correctly on the main screen in Slim Edition I finally don't have anymore questions for you . lol
Thanks

for all dead prophets

i saw lot of people have dead prophet problem, so i am here now to make a new thread to all this people and i hope to make it useful.
now we start
** FIRST : lets know names of prophet :
I mate Jamin, O2 XDA Neo, Qtek S200, Dopod 818 pro, Dopod 830, SPV M600, VPA Compact S.
** SECOND : we must know that before we trying to do any updating or change roms on my prophet i just need to do which called unlock for the prophet and then we after that been able to change any rom on my ( jamin ) and of course u need to be careful about Your device is it G4 or G3 ,
# and how we know its G4 Or G3 ?
# when u start Your Device u will see some numbers on left,
---------------------
IPL: 1.00.000
SPL: 2.20.000
GSM: 02.61.21
OS: 3.0.0.0
--------------------
and may be changed and that goes to the rom which You have, now we look for the last number on ( IPL and SPL ) , if we found it ( 0 ) it means You r G3 and if it ( 1 ) so You r G4 .
** THIRD : lets go to unlock , i will put programs in this thread it will help u in unlock.
-- Sync your device with computer and open the file u download it called HardSpl you will find two files one one foe G3 and G4 open your kind then you'll find a file called (( hardspl.bat )) okay, be sure your device is connected to computer then open the file and follow instruction and it will reset your device ,
now u ready to change rom.
TO BE CONTINUED
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
if any one can help please contact me.
hello
my device is jamin g4
it stopsat the boot loader and dono thing
can u help me please?
my e-mail is [email protected]
and suddenly after trying to update the spl been 1.01
please help me
can i fix it?
waiting for ur help
What is the IPL and SPL?
If the wiki where up, I'd suggest looking at that, but as it is I'll explain it now...
What ROM where you attempting to upgrade to?
To get the device back, I would say "Read the wiki" but it's down!!!
Download this ROM.
In ActiveSync, disable "connect through USB" (File->Connection Settings).
Put the device into bootloader (the three coloured screen) and connect it to the computer using the USB cable.
Run the file you downloaded earlier. This should then install a new ROM.
From there, just wait for it to finish.
Now, it should work!
From there, you could re install the Orange WM5 ROM, or try upgrading to WM6. Make sure you read all the relevant guides first!
thanks alot i did as u said but it stops at 80% or 88%
then show this message (error 326 invalid command )
please help me
i'm feeling bad
my mail is [email protected]
What brand the device? Has it been SIM unlocked?
hi again brothers, pal zerocool. first u must unlock ur device to be able to accept any rom after that and solve pproblems.
first flash this rom its offecial and it solve dead prophet problems.
then make hard spl by program open file called hardspl.bat.
make hard reset.
flash ur rom u want.
make hard reset again.
then enjoy.
i uploaded the hardspl program but i couldnt upload the rom its so big so u can look in ur mail u will find the solution.
u can extract file by any program for zip.and tell me the news
dont forget to look to ur mail. see all of u later
Dead prophet
Hi guys,
I have been using a sh... Nokia sine I broke my prophet G4 in december by upgrading the OS.
I had downgraded first to NVID and then I tried to upgrade and it fails at 95%.
Sine this day, my prophet seem totally dead, no light when plug on both charger or computer, windows do not recognize at all the device because it is turned off. And it really do not seem to charge...
I am living in China now and a guy told me I had to change the PB board...The ost is 100Euros, but I am almost sure I an find another solution...
The weird thing is I cannot charge it at all ( I mean no lights but does it charge a little?).
The guy tested my prophet with another battery and in that ase, it is stuck on the bootloader.
We tried several roms and it always fails at 95% and the error is 200 something, maybe 245 or 243, I do not remember sorry...
Is my phone hardware is dead? or it is just a software problem and I did not see the right guy?
Do I need to buy a new battery? I have read that sometimes the device is not able to recognize it even if it the offiial one and even if it is working on another device...
PLease help me I don't want to loose this phone that I've been using for almost 3 years...
Otherwise I will switch to an iphone but I am not sure to be as happy than I was with my prophet.
Xie Xie for your advice and answers.
Guilh1
Can it enter bootloader at all?
If yes, what are the IPL and SPL?
If not, it will be a hardware problem (may just be connectors to the battery but may be something more).
the only way of recovery is using jtag
but 1st we must discover the location of jtag pins on motherboard
I just do not know because with my actual battery, anything is possible....
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
I may be right about the battery onnectors though, but the problems seem to be from the phone connectors or the battery it self???
Thank you anyway for your very quick reply
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
Click to expand...
Click to collapse
If it can enter bootloader, it is almost certainly your battery at fault!
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/B] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
Click to expand...
Click to collapse
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/b] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Click to expand...
Click to collapse
Please look at this if you want more help, post here...
thanks alot dear samuraititio
but i can't flash it
it writes (no vender id)
help me please i tried another tool with the same nbf file it stops at 80%
and it automatically enter the boot loader
and i can't do ant thing
its information
jamin/g4
ipl 2.13.0001
spl 1.01
i think my problem is in the spl coz it was 2.13.0001
and now it's 1.01
how can i fix it please i still starter in this way so i'm trying;
help soon please
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
l3v5y said:
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
Please look at this if you want more help, post here...
Click to expand...
Click to collapse
hello pal i3v5y
i have the same problem
idid what u said the flashing stops at 80%
i need ur help please
i'm online at the moment and u too help me soon if u can please
my e-mail is [email protected]
waiting for u i don't have any other device to use and i need it
l3v5y said:
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
Click to expand...
Click to collapse
now i flashed the official rom of jamin but it stopped at 80%

HTC 8125 Bricked or NOT? What next?

Hi guys I need some help. I have a Cingular HTC 8125, I was trying to upgrade the rom on it to a new WM6 and here is what happened.
I have been researching the topic for about 3 weeks.
Its a G4 Device being upgraded with VISTA w/ Moded drivers for Ative SYNC
IPL 2.25.0001
SPL 2.25.0001
I used the shell tool to install one of the roms waited about 2 hrs and finally noticed that the window was NOT RESPONDING so I had to shut down and start over. The phone got to the second screen but froze there now showing
IPL 2.25.0001
SPL 2.25.0001
GSM 02.25.11
OS 10.1.0.811
On the Cingualr Background, I can still enter the Bootloader screen but nothing else?
Nothing else happens I cant connect the phone to the PC to do anything else.
Is it bricked or not is my question and what can I do to flash OEM rom or something that will work.
I tried OEM Cingular rom but I get ERROR 260 No connection to the phone?
Any help will be greatly appreciated!
Bricked phone
You should had firstly either hardspl or soft spl the phone b4 trying to load any rom
It's not bricked as long as you can see the RGB screen (Colors red, green and blue)showing the same IPL/SPL such as yours; IPL: 2.25.0001 and SPL: 2.25.0001. AND PLEASE BE CAREFUL WITH YOUR DEVICE CAUSE ITS G4 MEANING YOU CAN NOT JUST INTALL/FLASH ROM. Make sure that the Rom you flash not contain G3 IPL and SPL which is 2.xx.001. If so, then you will bricked your device.
Desiji is right, you should install rom with softSPL or hardSPL.
Try to flash the Official Cingular Rom or Wizard Love Rom. If success, then you can install other Rom using what desiji said. Just make sure that its a G4 safe rom. And another thing, try to charge battery using wallcharger not in the device. U need enough battery to perform rom flashing.
Hope this help revive your Wizard.
esdee007
WOW !
grrrrr8,you are a quick learner
CateraMV6
Yeah ! I certainly agree with esdee007 and desiji
Thanks
Hey guys thanks, thats what I thought but I think my main problem is the VISTA I need to get a hold of XP and try all that because the Vista is having issues with connecting to the phone at the moment, I can not get it to show it as a device. It does make a beep noise when you connect/disconnect it so its doing something but Vista is just too much of a pain in the rear to deal with.
Its a good news that its not bicked so all hope is not lost.
What is the opinion on Tmobile WING!? any reviews should I get that phone instead?
BTW where do I find these G4 Safe ROMS? and how do I tell if they have the IPL/SPL in them? Do I need to hack them to tell?
And is Soft or Hard recommended?
YUP ! sure vista is still not compatible for flashing,WinXP is highly recommended and trouble free.
All official stock roms are safe to flash both the devices G3 or G4,secondly,all the latest custom build wm6 or wm6.1 are safe for both the devices,as they don't include any IPL/SPL in them.
If you plan to flash many roms,than 'HardSPL' is recommended,coz its done only once and the device remains semi_Cid unlock untill you personally remove HardSPL,but with SoftSPL,its done everytime you want to flash a new rom,choice is all yours,how you want to go about it.

Categories

Resources