Hi guys,
I need your help. You'd make me amazingly happy if you could solve my problem.
I have an Orange SPV C100 (french one) and I keep trying to flash wm6.1 (the one Blackdragon_860 has released).
My problem is : I can't flash that rom. The updating process crash at 4% and I get an error saying that the ROM is corrupted.
Do you have any ideas to help me ?
Here are some additional information taken from the Hard-SPL And Soft-Spl walktrough :
1. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device
Click to expand...
Click to collapse
I've done that alright
, hold camera and launch spl.lnk -
Click to expand...
Click to collapse
I've done that too.
you`ll see the white screen
Click to expand...
Click to collapse
I have no white screen. Instead a file named JumpSPL.txt is generated... Here is what is inside :
-----------------------
Comandline is: 0x10000000 \SPL.nb
SPL File: \SPL.nb
Jump Address: 0x10000000
kmode is 0
SPL file size: 524288 bytes
3. From the flasher folder run ROMUpdateUtility.exe and follow instructions to flash the Hard-SPL if needed. or you can flash *ANY* oxygen rom
Click to expand...
Click to collapse
I've done that too. I put RUU_Signed.nbh from wm61OxygenUpdate1.rar in the same directory than ROMUpdateUtility.exe
Before the flashing process itself, ROMUpdateUtility.exe tell me I going to flash the image version from 1.7.74.1 to : 1.01
Then I have a rainbow screen which says :
ONBL : 1.07.0000
SPL : 1.07.0000
Oxygen : IU
The flashing process start, then crash and 4%... Saying that image file corrupted.
One last information :
I got the same error with other ROMS. Here the list of what I already tried :
Blackdragon_860's rom, released the 11-05-2008
Standard rom, the one that comes with Soft and Hard SPL (weight about 641Ko)
A Russian rom, taken today from zfree (here)
I didn't tried the chinese one. But as edgeofthestring has eventually the same problem than mine, I not will go for this rom.
I tried to be as complete as possible... I truely need some help.
Plz plz plz hrlp.
Thx
Guigoui
Try first flashing this rom:
http://www.megaupload.com/nl/?d=6B0FDY24
After this hard-spl and than flash any rom you like
Always use rom loader from hard-spl and before flashing rename rom to RUU_Signed.nbh
i also tried to flash the file posted by you but after 4 % the phone reboots and the setup gives me the: " invaliv vendor id " message
Default
ok. may it works when you do it like this:
1. restart your phone
2. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device
3. restart phone, don't connect to your PC!
4. open total commander, hold camera button and launch spl.lnk
5. Do you see a white screen? if yes proceed if not it has no
point proceeding, flashing will fail anyway!
6. Now connect your phone to your pc using the usb cable
7. From the flasher folder run ROMUpdateUtility.exe and follow
instructions to flash the Hard-SPL
8. After flashing Hard-Spl, to avoid reflashing, use always use
flasher from hard spl and rename the desired rom to flash to
RUU_signed.nbh
Hope this will finaly work for you!
i have tried it, i have the wm6.1 chinese version rom and the hard spl is not working at all in this rom, i have tried it with total commander and after the white screen appears and i connect the phone to the pc it is nor recognized by the pc...
thx nemphis for helping me... but it just don't work.
Believe me I'm not numb. I can read and use my little brain... I think I tried everything (including throwing my device to the other side of my room). There is something that keep my device from displaying this f*****g white screen.
Just for the record, I repeat, I have a french blocked orange C100...
If someone has got in the same problem and finally sorted it out, plz share how.
Nemphis, thx again but I doubt I will ever have wm6.1... Anyway I give up, so I guess I will never have wm6.1...
By the way, I also tried the rom you advised but as you so rightly said "if not it has no point proceeding, flashing will fail anyway!".
Thx you all...
c u...
by by
Is your phone sim unlocked also?
When reading through these forums there also are people saying you still need this: http://www.imei-check.co.uk/
Or ask your operator for the sim unlock code, they should give it when your phone is more than 1 year old.....
Phone simunlocked today... gonna try again tonight... Hope it will eventually work this time... Last hope anyway...
guigoui said:
Phone simunlocked today... gonna try again tonight... Hope it will eventually work this time... Last hope anyway...
Click to expand...
Click to collapse
Was your phone "app unlocked" before begining ? I would assume it is necessary, but won't pretend I'm a guru...
Christophe - Lyon - France
@guigoui :
I had this same, white screen didnt appeared .. but after unlocking using this way: http://rapidshare.com/files/105133496/Unlock_HTC.rar.html you'll see it (after runing SPL.lnk with camera button pressed) all is working !!!
I've WM6.1 !!!
Thanks!
This sounds pretty good vovakk... I'll test your file tonight (because I had no white screen after having my device simunlocked)
I can't to stand waiting until tonight...
It WORKED !!!! Now I have WM6.1 !!!
Ok so here are some additional information that could be useful.
Be sure you have .net framework 2.0 or newer before starting the unlocking process (the file shared shared by vovakk) otherwise you would be stuck at the second step.
When at step 5, I'm not sure which profile is required but, for me, it worked with "No security".
Once you've done step 5, you'll get THE white screen when laucnhing SPL.Ink (I confirm). You can start flashing.
I've flashed several rom as nemphis told me to, and it worked. Here is the list in the right order, with some notes :
1. http://www.megaupload.com/nl/?d=6B0FDY24 (given by nemhpis) : takes about 2-3 minutes, when done, I believed that my device was dead because it took a while before the PIN screen showed. Don't panic, just wait.
2. http://rapidshare.com/files/65732449/hspl.7z.html (the original Hard-Soft SPL - created by sp3dev) : extract, don't change anything, just launch RomUpdateUtility.exe. Flashing process takes less than 1 second
3. http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar (THE Windows Mobile 6.1) : In the RomUpdateUtility.exe folder, just replace the original NUU_signed.nbh by the one inside wm61OxygenUpdate1.rar. Launch RomUpdateUtility.exe. Eveything else is like 1. except that my device rebooted fast without being stuck a while on the windows mobile logo screen. The device reboot, you enter your PIN and then welcome to WM6.1 !
Hope someone would find interesting to read my so long posts...
I thank you all for your patience and help... I wouldn't be able to do it by myself.
C you
hey GuiGoui can you upload this file here or Rapidshare please. Megaupload is way tooooo slow. RUU_OxygenWM5_1.5.401.2_R3_4.1.13.28_02.67.90_HTC_EUR_Test.exe
thanks
I can't.... 8Mo limited...
guigoui said:
It WORKED !!!! Now I have WM6.1 !!!
Ok so here are some additional information that could be useful.
Be sure you have .net framework 2.0 or newer before starting the unlocking process (the file shared shared by vovakk) otherwise you would be stuck at the second step.
When at step 5, I'm not sure which profile is required but, for me, it worked with "No security".
Once you've done step 5, you'll get THE white screen when laucnhing SPL.Ink (I confirm). You can start flashing.
I've flashed several rom as nemphis told me to, and it worked. Here is the list in the right order, with some notes :
1. http://www.megaupload.com/nl/?d=6B0FDY24 (given by nemhpis) : takes about 2-3 minutes, when done, I believed that my device was dead because it took a while before the PIN screen showed. Don't panic, just wait.
2. http://rapidshare.com/files/65732449/hspl.7z.html (the original Hard-Soft SPL - created by sp3dev) : extract, don't change anything, just launch RomUpdateUtility.exe. Flashing process takes less than 1 second
3. http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar (THE Windows Mobile 6.1) : In the RomUpdateUtility.exe folder, just replace the original NUU_signed.nbh by the one inside wm61OxygenUpdate1.rar. Launch RomUpdateUtility.exe. Eveything else is like 1. except that my device rebooted fast without being stuck a while on the windows mobile logo screen. The device reboot, you enter your PIN and then welcome to WM6.1 !
Hope someone would find interesting to read my so long posts...
I thank you all for your patience and help... I wouldn't be able to do it by myself.
C you
Click to expand...
Click to collapse
How did it work............ i ended up lockin my phone it was unlocked before... now no application works... anymore it say this application is not have signed certificates..... PLZ ANY1 HELP I DONT EVEN KNOW HOW TO HARD BOOT THIS HANDSET..... I NEED URGENT HELP PLZZZZZZZZZZZZZ...
Related
hey))) as promised, the Soft-SPL and Hard-SPL
1. Soft SPL - loaded to ram temporarily, erased after reboot, use it to flash HardSPL or tested working roms.
2. Hard SPL - A version which is flashed to rom.
So, what`s this?
1. Based on oxygen spl, but
1. Doesn`t check CID
2. KeyCard security is reset
3. Allows to flash unsigned (custom) nbh files.
http://rapidshare.com/files/65732449/hspl.7z.html
Instructions:
1. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen
2. Connect USB to pc
3. From the flasher folder run ROMUpdateUtility.exe and follow instructions to flash the Hard-SPL if needed. or you can flash *ANY* oxygen rom
4. After flashing Hard-Spl, to avoid reflashing, use
nbhextract ruu_signed.nbh
with any official update.it will dump the nbh. you`ll see some file like 00_OS.nb0 or 04_OS.nb0, any *_OS.nb0
use Htc Rom Tool (can be found on forum) and go to build rom, select OXYGEN, use 1.0.000.0 version, and go to system box, and press "..."
Load your os.nb0 and press build rom. then you can use this nbh to flash os. just replace original nbh file within updater directory.
p.s. sorry, have problems with wm6 - no info when i`ll finish it
Good Jobs :d
THANX SPV3DEV foor tool . WM6 for tis device ?
THANK YOU GREAT JOB. not tested yet. but thanks for the efforts.
how is WM6 comming as you promised?
sp3dev,
Thanks I have CID unlocked my phone.
Please I need to SIM unlock it.
how I can do it?
Please help.
Doesn't work for me.
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
quell said:
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
Click to expand...
Click to collapse
You passed in boot mode? Long push camera and short power.
No...I didn't pass. Phone has white screen, when I run RomUpdateutility.exe before flashing shows me error.
Have ideo when your WM6 rom will be finish ?
Thx for the tool , great job .
wm6
HI. Please Guide coking rom for Htc S310? Thanx
quell said:
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
Click to expand...
Click to collapse
I've this problem too. Running windows vista aswell. Anyone found a solution?
RUU on vista
the solution is here:
http://www.modaco.com/content/Windo...U-on-Vista-It-can-be-done-the-ultimate-guide/
Hello all
my phone is fully unlocked
i soft-spl my orange c100(htc 310) and when i tried to hard-spl it just crashed wile writing the new spl
now i am stuck at tri-color boot screen
Does somebody have orange c100 romania rom?
Thanks
Maybe you will help me...
sp3dev said:
4. After flashing Hard-Spl, to avoid reflashing, use
nbhextract ruu_signed.nbh
with any official update.it will dump the nbh. you`ll see some file like 00_OS.nb0 or 04_OS.nb0, any *_OS.nb0
use Htc Rom Tool (can be found on forum) and go to build rom, select OXYGEN, use 1.0.000.0 version, and go to system box, and press "..."
Load your os.nb0 and press build rom. then you can use this nbh to flash os. just replace original nbh file within updater directory.
[/QUOTE=sp3dev]
Hello!
Maybe you Sir have an official Oxygene ROM image? Maybe you dumped it for yourself before all thos updates? I am extremally looking for it Please let me know if you could send it or upload somewhere.
Best greetings,
RA
Click to expand...
Click to collapse
Hi,
Where do I place hard spl?
When pressing this I first press camera and then open spl.ink ? Or is there another way I should do this?
i am from romania and i have spv c100.
if you could tell me how to back-up my rom i will help you.
hi SP3DEV
in step 1. "Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen" how do I do this? I copied the 3 mentioned files to root directory but how do I hold the camera and launch spl.lnk at the same time. Please explain this thoroughly. I just bought an HTC S310 and want to upgrade my toy. Thank you much
charlietruong said:
in step 1. "Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen" how do I do this? I copied the 3 mentioned files to root directory but how do I hold the camera and launch spl.lnk at the same time. Please explain this thoroughly. I just bought an HTC S310 and want to upgrade my toy. Thank you much
Click to expand...
Click to collapse
same problem.. any solution?
Cease & Desist!
Hard-SPL is *MY* trademark, I never said you could use it.
PSYCHE!
just kidding, but tell me sp3dev, when you disasm the SPL; are you actually rebasing the file, or just going at it by trial and error... because it shouldn't take more than 5 minutes to hack up a Hard-SPL and SSPL.
Also... really you should only call it Hard-SPL if it prevents itself from being overwritten, otherwise it's just a USPL... not that I particularly mind.
Ive got a "bricked" S200 G4 (I think)
Text in rainbow screen is
"ILP 2.20.0001
SLP 2.10.0001"
I dont know if the difference here matters.
Tried to upgrade with different ROMs, but no luck, upgrade stops in the process, different % every time.
But the latest Speedking 2 ROM I managed to install. Hopefully I softbooted and got the same rainbow screen.
Any advice?
Why didn't you hardspl your prophet ??
I did, but maybe wrong hardSPL? It is a jungle here, hard to find the right info I need because its so much.
hpn said:
I did, but maybe wrong hardSPL? It is a jungle here, hard to find the right info I need because its so much.
Click to expand...
Click to collapse
1. not 100% of our Prophet can be hardspl done ( like mine )
2. if so, just go straight ahean with my lazt_tool, too easy though....
3. hardspl is just a flashing process but only spend a couple of minutes unlike rom flashing, (from 5 - 10 minute.)
all you have to read in the sticky post on the top pf this forum
I recommend youto read post 1 of this thread....
http://forum.xda-developers.com/showthread.php?t=353547 as follow....
20080601added:
[size=+2]Lazy_Tool (thks YOUZII) is for flashing all nk.nbf, in win-xp PCs, ........[/size]
WANNA GO OLDER ROMS? READ THIS POST THOROUGHLY ^_^ )
P.S. You can just change / replace the nk.nbf inside the Lazy_Tool folder if you wish to flash other roms....
20080529 added:
Cloudyfa's 19213 clean rom + Lazy_Tool, simple, fast, error free, a new upgrade tool.
[size=+3] Additional RECOVERY steps for 3 colors screen boot-up after flashing...[/size]
a. Force Bootloader Mode MANUALLY (see below Point 4 for How To ), Then flash PVtemp or NVID for prophet( P.S. the boot up screen will be changed to Qtek...),
b. ( Optional) Use Lazy_Tool to upgrade to WM6.1 (default rom is Cloudyfa's 19213-clean, you may change if you want...)....^_^,
Click to expand...
Click to collapse
20080423 added: Alternative "Lazy_Tool"
some hints ~~
if error persists while upgrading with this tool,
Please ask yourself...
I. did I softreset yet? did I make the Prophet recovery? (remove battery and sim card),
II. will the USB port of my PC currently too heavy loaded?
III. did I restart my PC yet?
IV. any connection related software other than activesync is running?
V. did I try the rear panel USB ports?
V.I is my PC currently too busy?
VI. did I try other USB cable yet?
VII. did I try the force bootloader manually before upgrade?
VIII. Did I hardreset my prophet after new flash(if everything had done but no help~~~~ ) ^_^
**************************************
2008-02-18 added ***
NVID for prophet,
Click to expand...
Click to collapse
HARDspl
(OLD method is at the bottom of this post)
1: "DON'T PANIC",
2: 99.9999% CAN BE RECOVERED BY
DOWNGRADE TO WM5 WITH entering BOOT_LOADER MODE + flashing the PVtemp (old method step 1).
3: IF USB CONNECTION ERRORS, TRY REMOVE BATTERY FOR 1 MINUTE and try again.
4: FORCE BOOTLOADER MODE MANUALLY HOW TO = ....
4a. keep pressing the Commgr button and
4b. in the same time keep picking/sticking the bottom softreset button with stylus for one second,
4c. [size=+2][highlight] THEN ONLY ONLY RELEASE THE STYLUS[/highlight][/size] and wait for the screen
TO CHANGE to the three color screen (bootloader mode),
4d. then release all and go to step 10 below..... !!!
Click to expand...
Click to collapse
(remember to download and prepare all files you needed first, or you may have errors while in the upgrade process)
Click to expand...
Click to collapse
5. Execute the Rom Upgrade Utility (ROMUpdateUtility_NV_G3.exe ( or G4), in the
HardSPL folder that you had downloaded, all activities will only take 2-3 minutes to go and
nothing will be seen in the Prophet screen.
(P.S. if connection Error, NO PANIC, soft reset OR remove battery for half a minute and try again. )
6. after the flash completed, it will restart automatically.
7. done!! in your prophet, nothing will be changed VISIBLY EXCEPT the digits IN the reboot screen !!!!!
and while booting now YOU MUSTBE ABLE TO SEE information like: 2.G3.4PDA (FOR G3 PROPHET) or 2.G4.4PDA (FOR G4 PROPHET)
Prophet Hard SPL isn't yet completed until the SPL shows
"2.G3.4PDA" or "2.G4.4PDA". ^_^ !!!
Alternate way to Flashing / upgrading your Prophet to WM6,
a. ENTER BOOTLOADER (see how to at the upper part of this post) [size=+2]OR [/size]
b. DO THE JUMPSPL...(step 8-9 BELOW) [size=+2](you can force to bootloader mode instead of step 8 to 9)[/size]
8. copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,
9. Execute the SPL.lnk IN THE DEVICE (using the Total Commander is recommended), then you see Prophet in all bright or white screen,
10. Plug back to the USB port ( connect to rear USB panel of the computer - recommended) to the device,
11. Execute the Rom Upgrade Utility to upgrade to your chosen rom
(or put your NK.NBF to the unzipped WM6_Update_Utility folder), all activities will
only take 3-5 minutes, nothing will be seen in the Prophet screen.
12. Finally, after 100%, be patient, just wait, and Prophet will reboot automatically.
13. OF COURSE, after it auto-restart, [size=+2]better one more time HARD-RESET[/size],
ALL will be OKOKOK !!!
[size=+3]Tradition (OLD) method[/size].... (for ROM with OS.nb ),
1. Connect to PC, activesync now OK, Flash with [size=+2]PVtemp[/size] or NVID for prophet for step 1
WHEN FINISH,
2. TOUCH NOTHING, HANDS-UP !!! leave it alone, just don't touch your prophet...... ( WM5 wwe flashing now finished)
3. [size=+2]ACTIVE SYNC WILL POPS UP soon, JUST DON'T TOUCH IT (disregard it) [/size],
4. THEN RUN UPGRADE.BAT from PC to flash to WM6 (should be included in your old ROM package with OS.nb )
5. follow the on screen steps and YOU WILL GET WHAT YOU HAD EXPECTED THEN~~~~~
[size=+2]PLEASE REPLY IF YOU THINK HELPFUL ABOUT THIS MESSAGE !! ^_^ [/size]
Click to expand...
Click to collapse
I`m running Mac, with XP under Parallels. Upgrading Trinity is no problem on his config. But your reciepe include running command window. I cannot connect to the prophet from command window.
Trying to solve this somehow. Thanks for the link.
Hi guys, I've just tried to unlock my ameo and am stuck at the bootloader screen. I have a wm6 rom downloaded and am trying to put it on however, I cannot work out how to do it. I cannot get a RUU to access my ameo as it isn't active sync'd. can anyone tell me which program to use to get the rom on the machine?
thanks
If all its correct the bootloader should say "SPL1.20 olipro"
at the bottom of the page it should say "serial"when you plug athena in the pc USB port it changes to "USB"
Just download a rom appropriate for SPL1.20 unpack it in a folder in your desktop and click in the installer.
Remember that any memory card you may use has to be taken off the athena before you do anything.
also if bootloader do not say SPL1.20 a rom for SPL1.20 wont work.
Hi PBL, thanks for the response.
I have 1.20 listed and usb at the bottom.
I have downloaded the wm6 file but that is all there is, when you say click on the installer, I don't know what you mean, windows asks what to open the file with. Could you give me a link for a wm6 rom with a downloader?
Cheers for any help, I know how annoying noobie questions can be.
Phil
Have you found it out already or do you still need help?
Help still required!
After using AthenaUnlocker for the first time, your bootloader has been updated to Olinex 1.20 (appearing on your screen), however you still might have no ROM installed. => black screen after resetting your Ameo.
Additionally, your Ameo is still locked for other ROMs (as it was with mine), so no unofficial ROM here might work at first. In your case you need an official Ameo WM6.0 ROM found here , if you already have it, the better.
- (Download the ROM onto your PC),
- be sure that your Ameo is turned on and connected to the PC.
- start the romupdateutility.exe (admin rights on the PC, no SIM-card or mini-disk inserted into the Ameo), accept the warnings and click next, it will tell you your current ROM version and the one to upload, hit next and so on, finally click on update, after a while the status screen on the PC screen will also appear on your Ameo.
- wait until it is done and the Ameo has rebooted and installed
- restart the Athena unlocker and repeat steps 1 to 3
No matter what you do: NEVER disconnect the device from the PC during upload!
Hey will, Just done that, all went well, 100% upload, screen went black, comp says no connection, now I have a red light round the joystick and cannot turn on or get to bootloader!!!!!!!!!!!!!!!
Any ideas?
Have you updated the T-Mobile-ROM? Did you press the camera-button AND reset button? The Olinex-bootloader screen should appear.
Updated the rom, then it went blank and the red light appeared, now I cannot get the bootloader screen up
wait a minute!!!!!!!!!!!!
SHE LIVES!!!!!!!!!!
Am i right in thinking I now need to do all 3 steps in the unlocker again?
I forgot to tell you the most import rule: Dont panic!
Yes, repeat steps 1-3 from the Unlocker, start with step 1, I will wait for you.
JUST a second: Your device is showing Olinex v1.20 when in bootloader mode AND/OR your 6.0 ROM is starting now, correct??
Cheers Will, The battery is as flat as a fart at the mo, so gonna leave it till the morning. Thanks for your help and I'll post here tomorrow to let you know how I go.
Thanks agin, you're a life saver!
Phil
Glad your Ameo didn't break.
Loading the battery to 90+% is essential as it might break your device during upload.
Remember: after each ROM update (Radio update also etc.) the device will perform a hard-reset, so you have to wait each time until your Ameo has finished installation and has resynced with your PC.
IF AND ONLY IF the ROM itself has been loaded without problems and your Ameo has synced with your PC, then
- proceed with Athena unlocker, repeat step1 => wait for full installation and resync (don't close Athena unlocker) => hit finish-button on PC
- do step 2 (update), then WAIT for reset, full installation, and resync BEFORE proceeding on the PC because
- as for step2 the unlock-program will be copied and started onto the Ameo itself (that is why you have to wait)
- hit OK on the PC (the screen will inform you about the unlock process on the PDA, hit ok if the device is synced and ready), on the PDA you have to accept the installation of the program, hit install?/yes? there and unlock BOTH SIM and CID (=ROM unlocker), so you can use any phone-provider and any unofficial ROM
- finish the installation on your Ameo (hit unlock and afterwards OK etc. somewhere on the screen, I can't remember if it will hard reset again), then
- do step 3 on the PC, the same upload and hard reset and waiting procedure as before.
Done! Now you should be able to use any SIM-card and update any unofficial ROM (v1.2 versions ONLY for the moment, BEWARE!).
Hope this helps for the start.
Sorry I lost track on you pthechemist but will seems to be doing a great job here, as long as you have spl1.20 already installed and follow the procedure, you are pretty safe although it can be a bit scary.
Good luck
Cheers for the help and support guys.
All is now running PERFECTLY!
Just in the process of finding some decent games to put on and get tomtom setup
Oh, while I think about it...
The guy who I bought the phone from had a customized home screen which I cannot seem to replicate, any chance it was a downloaded theme? if so, any recommendations?
Good work!
Ad TomTom: lookout for post#1 in this thread, the settings there did definately work with my TomTom7.
Ad skin (remember: 1.2 only with Olinex v1.20): I've been using MichyPrima's R5.1 for a while now, there is the big HTC home screen (black_vga) with this big watch (aka x7510). Another one is the Diamond skin. Just look around, there are multiple skins for tryout.
Hey Will,
Thanks for the info, will have a look around for skins
Hey Will,
Thanks for the info, will have a look around for skins
Hello Everyone!
This is a step by step guide for unlocking the SPL of your HTC P3400 or P3400i.Please read and follow everything given here carefully and you will have your phone unlocked within 15 minutes.
This is a step taken in order to minimize the accidental bricking scenerios happening almost everyday here.
The Guide is divided into 2 Parts, A FAQ section and the Unlocking Guide Section. I request you to please read all of this before doing any furthur steps. ROM Flashing can be very dangerous if not done properly.
Enjoy!
Frequently Asked Questions
FAQ (Frequently Asked Question) Read Carefully Please
Q1. What is the basic information about my phone that i would need to get started with this process or for troubleshooting?
Ans. The basic information that you need is displayed on the white htc splash screen that shows up when you start your phone. This inludes:
ONBL version, SPL version, GSM or Radio version and OS version.
Apart from that, you will also need the serial number of your device. This can be found behind the battery on your device or on one side of the packaging box in which your device came.
An optional thing that may come handy is the version number of your ROM which can be found by going to Start > Settings > System > Device Information. Look for the ROM Version there.
Q2. What is SPL, Why it needs patching, and what are the things i need to keep in mind?
Ans. SPL or Second Program Loader is a part of your phone's firmware. Its responsible for both loading of operating system and it is also used by operating system for some low level tasks. By Default, HTC and Other Manufacturers too, design it in such a way that it does not allows custom ROMs to be flashed in the phone. It does no by checking for the Digital Signature of HTC on roms. So it need to be patched in order to flash custom ROMs made by chefs in this forum.
There are two SPLs available right now for P3400 and P3400i. One is Olipro's SPL for Old Gene and Second is Orefkov's SPL for New Gene. These should be used according to the device they are meant for. Using wrong SPL can make your device dead.
One more thing is, SPL is needed to be updated just once. Only one of the given SPLs will work for you and you will never need to patch it again. This is true for those situations too when you flash a rom and your phone does not boots past the White HTC splash screen. In that case too, As you have just flashed an incompatible ROM, you just need to use another, compatible ROM to get your phone back. NEVER UPDATE YOUR SPL ONCE IT IS PATCHED BY EITHER OF THE METHODS
Q3. How can i be sure which version i need to use, i am not sure whether i have an old gene or new gene?
Ans. Earlier it was being thought that one can differentiate between New Gene and Old Gene on the basis of Onbl and Serial Nos. But this has not found to be true as evident from many cases of bricking.
One of the possible checks for knowing that is if your phone originally came with Windows Mobile 5, its probably an old gene, and If it came with Windows Mobile 6, its probably an New Gene. However, this is also not a concrete basis to decide the version of SPL.
So i recommend to follow these steps, These should work for any Gene without problem.
1. Use the Olipro method first. It will work properly if your device is an old gene.
2. If it fails and your phone becomes dead, just follow the instructions for using Gene Unbricker for new gene and your phone will be back again. This way, your new gene will be flashed with Orefkov's method.
Q4. Are there any precautions that i need to take when selecting a ROM for flashing to my device?
Ans. Yes, there are indeed some things that you need to keep in mind before making mind to flash a ROM.
1. Make sure your SPL is patched, ie. On boot screen it should have either SPL 1.10.Olip displayed in case of an old gene OR SPL 1.07.Oref in case of a new gene. If it is not, patch it using the Guide given below. If it is, dont ever try to patch it again.
2. After patching your SPL you will become sure that whether your phone is a new gene or old, because of knowing the version of SPL that worked for you. Now, never choose a ROM which is not built for your phone. Only use ROMs appropriate for you phone. And if you ever accidently flash a ROM of wrong version, dont panic. Just flash another ROM for your version and your phone will be back.
3. In general, never try to downgrade your ROM. Means if your original ROM was WM 5 and you upgraded to WM 6 or 6.1 Dont try to downgrade to WM5. This is specially true for WM 5 because of reasons i'll explain later.
Q5. Why is it not recommended to downgrade the OS version, ie. moving to a previous ROM version?
Ans. There is no problem actually in doing so. But there are some situations that needs to be taken care of. What happens is, Somtimes, the previous version of Original ROMs from htc, contain the older version of SPL that is very specifically made for that version of ROM.So if you flash this ROM, your SPL will again become locked. This is specially true for original WM 5 ROMs
In case your phone came with WM5 originally, and the version of ROM exactly with the one that was originally on your device, It wont give any problem. But if this ROM is not exactly the version your phone originally came with, this will brick your device and you'll have to take it to service center. No homemade solutions works then.
Even bigger problem arises when your phone came with Wm 6 originally and you try to downgrade it to WM 5. This will certainly brick your device and force you to take it to service center. SO DONT EVER TRY TO DOWNGRADE A GENE TO WM5 IF IT ORIGINALLY CAME WITH WM 6.
ROMs created by users here do not contain the ONBL, SPL and GSM parts (dont worry about the names). These only contain the OS part which is safe to use.
Q6. What are the things i can try if i get a problem while this process?
Ans. You shouldn't get any trouble if you take all the precautions, but even if you do, you can try :
1. If your gene is bricked by Olipro SPL, use the gene unbricker for new gene by Orefkov.
2. If you flashed your phone with a ROM made by some user on this forum and it doesn't works, just flash another version of the ROM or some other compatible ROM. NO need to touch anything else.
3. If you downgraded/Upgraded using any of the Original HTC ROMs and your phone is bricked, try the JTAG Method by Orefkov. Search for it, you'll easily find it. If even that doesn't helps, Take your device to service center.
Q7. What is bootloader mode, and how do i enter it?
Ans. Bootloader mode is a special mode which is use to flash ROMs. Bootloader is the part of your phone's firmware that kicks in even before SPL and initializes it. You may need to enter this mode while patching your SPL or sometimes while flashing a ROM. To do that, Shutdown your phone, Press and Hold the Camera Button and press the power button or the soft reset key using your stylus. This will take you to a 3 colored screen with your Onbl and SPL version displayed on it. This is called the Bootloader mode.
Q8. What is Hard Reset and Soft Reset and how to do it?
Ans. Soft reset is a second name for restarting your phone. It can be done using power button too but sometimes, when the phone is hanged, it needs to be done by pressing the soft reset key, situated in a small hole near the mini usb port you use for charging and headfone, using your stylus. Your phone will restart immediately without any harm. But if you have any unsaved data, like an open, edited word file or a text message half written and not saved, they will be lost. But all your saved data is safe.
Hard reset is something that needs to be done when there is some problem with the phone that is not being solved using any standard method or restarting the phone. This method erases all the files and data in phone memory (not SD card) and makes your phone as it came new from factory or just after a fresh ROM upgrade. You'll loose all your emails, calender items, Todo list, sms, contacts etc. But most of the problems get solved using this. So before using this, backup your PIM data using utilities like PIM Backup by dotfred etc.
To do a hard reset, shutdown your phone, Press and hold the two soft keys (the keys above the call accept and call reject keys) and press the reset button using stylus. A black screen will appear warning you about the consequesnces. Press the Green key (call accept key) to start the process.
The Step By Step Guide
The Step By Step Guide
CAUTION: DO NOT UPDATE ROM OF A PHONE THAT IS SIM LOCKED. THE RESULTS ARE UNKNOWN BUT MOST OF THE TIMES IT PREVENTS YOU FROM USING THE PHONE ANY FURTHUR!!
If you like to backup your existing rom first, follow this guide by Ankit360 to do it : http://forum.xda-developers.com/showpost.php?p=3215838&postcount=20
Step 1: Download the Tools
-------------------------------
Download the tools zip file from here:
http://www.4shared.com/file/81084740/fa599d63/SPL_Unlocking_Tools.html
Its a self extracting file, just start it and give a path and it will unzip all the files in your chosen folder. Inside the extracted folder you will find these things:
1. SPL Updater : Inside it there are 2 folders, Olipro and Orefkov. These contain the two SPL patchers that we need to use.
2. ROM Update Utility : This contains the ROM update utility we will need to flash a ROM. Unzip it into a folder.
3. USBDriver4ActiveSyncVista : This contains a special driver for Windows Mobile Device Center in Vista that you need to use to successfully update your ROM. Unzip it in a folder too.
4. Download a ROM appropriate for your device: Which one is appropriate, you'll only know after updating your SPL. So do this step after that. But in any case, here is a link to a good ROM, created by me, which is available for both new and old gene:
Sumit's Pro Users ROM (WM 6.1, for new and old gene)
http://forum.xda-developers.com/showthread.php?t=467796
Step 2: Preparing your phone
--------------------------------
1. Copy the file gene_hspl.exe from the SPL Updater\Olipro folder that you got in step 1 to the phone memory.
2. First, on your phone, Go to Start > Settings > Connections > USB to PC. Here, uncheck the checkbox : enable advance nerwork functionality. Click OK. Disconnect and Reconnect the USB cable to your pc.
Step 3: Prepare your Computer (Please pay attention, this is crucial!)
--------------------------------
XP Users
----------
There is not much you need to do. Just open task manager and kill the Active Sync executable from the processes tab. Its named as wcescomm.exe.
Vista/Windows 7 Users
-------------
You need to take these steps :
1. Go to desktop, right click Computer, and select Manage. Go to Device Manager. Now under the section Mobile Devices, Double Click : Smartphone USB Sync.
2. On the Drivers tab, click "Update Driver..." button. On next screen click : "Browse my computer for driver software".
3. Click : "Let me pick from a list of device drivers on my computers". Click "Have Disk.." on next screen. Click "Browse..." and go to the folder extracted in step 1. There, go to USBDriverforActiveSyncVista folder. Here select the file "wceusbsh.inf" and click OK.
4. Click Next and finish the wizard.
NOte : YOU NEED TO DO THIS TO SEE THE "USB" BUTTON IN MTTY WINDOW IN LATER STEPS. DONT SKIP IT!
Step 4: Use the Olipro method first.
-----------------------------------------
Open File manager on your phone. Go to the location on phone memory where you saved gene_hspl.exe. Tap on it to run it. Your phone will restart after a short pause.
Now there are two chances :
a) If its done alright, you'll see SPL 1.10.Olip on your boot screen and your phone will boot just fine. And it confirms that you have an old gene. You do not need to do Step5. Proceed to Step 6.
b) If it doesn't boots, and only green and red keys blink, Don't worry. Your phone is bricked but you'll get it back using orefkov's method in a minute. Proceed to next step. And this confirms that you have a new gene.
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
Step 7 : Set your PC and Phone back to normal
------------------------------------------------
This step is only needed in case you are using Vista.
The driver we updated in Vista will not work for normal active sync operation. So you'll need to set it back to the original version. There are two ways to do that. Either, uninstall and reinstall the Windows Mobile Device Center Or Follow the same procedure gicen in Step 3 but instead on clicking the "Have Disk button", choose the driver from the list already given.
The driver that you need to install can be identified by have a newer version given in front of its name. Also, the newer driver's name includes "Microsoft Corporation" while the older one has only "Microsoft".
You can Put back your SD card now.
On your phone, again go to the Start > Settings > Connections > USB and check the checkbox there and click OK.
That's it! You are Done.
Credits
Thanks to these people whom work helped me greatly in writing this Tutorial:
Ankit360 for writing the original tutorial.
Olipro for providing the SPL for old gene.
Orefkov for providing the Gene Unbricker for New GENE.
Nevermind_me for sharing his real experience as an end user and help in updating the guide.
NEW BEE
The info being provided is very informative,there is no way i can go wrong with these steps.hope it helps unbricking my phone.thanks to the people involved for making it happen.you guys rock.gonna try these steps will let you know if i got it rite.
your fellow new bee
I TRIED THE SUMMITS STEP B STEP GUIDE AT THE POINT WHER MMTTY PROG SUPPOSE TO MAKE SCREEN ON PHONE GO WHITE IT GIVES ERROR MESSAGE SOMETHING ABOUT CAN'T DOWNLOAD IMAGE,OR SOMETHNG
My P3400i SR8XX is OLD or NEW?
Hi! Crazy & Ankit,
I am from Delhi and having P3400i with SR. HT8XXXX, onbl-1.17.000,spl-1.17.000,os-1.8.00.
In the past I have flashed several times of cooked rom by chayn & lomlom without changing to permanent HSPL. It was done by temporary CID unlock method as running jumpsp.exe while pressing and holding Camera+VoiceReco button and flashing. Presently we are using Vista Design build 20270 by Chayn and and still my onbl& spl displays 1.17.000.
Today I tried to flash Ankit M2D rom using previous method, flash completed successfully, device restarted but stuck on boot loader. Then i restore my Gene by RUU_Gene_hTC_Asia_India_1.17.720.1_4.1.13.34_02.79.90_Ship and then flashed Chayn Vista Design 20270 which is working fine.
Please confirm whether my Gene is NEW or OLD as if it were NEW then Ankit's ROM Should work. Sorry for my bad english.
Thanks..........
Yours is an old gene i guess. Using Serial No, ONBL and SPL versions for recognizing your phone as a new or old gene is not reliable. chyan and lomlom's both have provided some excellent roms for both new and old gene so i cant say about that also. But ya, if Ankit's ROM is not working then yours is an old gene, i am 99% sure.
Thanks for your quick response to our query. Further, could you please advise me better ROM for me to Flash.
Also, I have created 1% increment battery dll and tested on my gene which is working fine. Is it possible to include it in your ROM.
@krazy
Oh Boy! Now we have an old Gene (3400i) with 8 series number and 1.17 onbl. Great going HTC !
Guess you have some really busy time coming up.
BTW:
Do you know typing? Better learn it soon .
What to say brother, HTC is just making things difficult, i guess they want to sell the higher end mobiles too. But i dont understand, apart from WinMo 6.1, their higher end mobiles have faster and greater hardware. So how come flashing a gene with WM 6.1 and Manilla 2D can affect their sales? I wont go for a P3400i if i had the money to buy a diamond even if both of them can/already have WM 6.1.
I know typing very well, you might have got some idea from the amount of text i post when i post a new rom I am ready, give it to me baby! Yeah! LOL!
qasidakbar said:
Thanks for your quick response to our query. Further, could you please advise me better ROM for me to Flash.
Also, I have created 1% increment battery dll and tested on my gene which is working fine. Is it possible to include it in your ROM.
Click to expand...
Click to collapse
Hey man, its really nice! Love it. Will include it in ROM is some more users gave positive responses, as you know that the ROM is not for somebody alone, its for the community. So will have to take some feedback before including. I'll post it in recommended downloads section in both of my roms. Thanks for it mate
krazy_about_technology said:
Yours is an old gene i guess. Using Serial No, ONBL and SPL versions for recognizing your phone as a new or old gene is not reliable. chyan and lomlom's both have provided some excellent roms for both new and old gene so i cant say about that also. But ya, if Ankit's ROM is not working then yours is an old gene, i am 99% sure.
Click to expand...
Click to collapse
You are 100% right, my gene is absolutely OLD. I have downloaded and flashed your OLD Gene 1.04 rom and it is working fantastic. Thanks again your are really the Crazy Sumit.
Yeh, I know I am Krazy, but Krazy with a K not C! Got it
Rom in PTG
Hello staff of the forum can be a rom in PT to Gene 100 HTC P3400?
thanks
Phone Info:
S/N:SZ71xxxx TMN ONBL: 1.07.0000 SPL: 1.07.0000 OS:1.7.0.0
puto116 said:
Hello staff of the forum can be a rom in PT to Gene 100 HTC P3400?
thanks
Click to expand...
Click to collapse
There are no 'staffs' in this forum, we all are members just like you . Please elaborate your phone details (the details your device shows when you switch on), then someone will be able to help you out.
@qasid: The battery bar did not show up in my Gene in the top bar . Using a manilla2D version. any ideas?
@shaunak! Have you tried sdkcerts patch, I think it will solve the issue.
qasidakbar said:
@shaunak! Have you tried sdkcerts patch, I think it will solve the issue.
Click to expand...
Click to collapse
Yup! its already installed, since I am using color icons. Can you please post a screen shot ?
Rom in PTG
sorry
Hello staff of the forum can be a rom in PT to Gene 100 HTC P3400?
thanks
Phone Info:
S/N:SZ71xxxx TMN ONBL: 1.07.0000 SPL: 1.07.0000 OS:1.7.0.0
Addicted2xda said:
Yup! its already installed, since I am using color icons. Can you please post a screen shot ?
Click to expand...
Click to collapse
Please see post#8 for screen shot.
backup orignal rom
to bauckup orinal rom orefkov created small programm for it.
Programm dump_gene_os_extrom.exe do dump os and extrom from Gene to memory card. Created files are identical os.nb and extrom.nb, extracted from official RUU_Signed.nbh, and allow rom coocking with it.
Usage:
Copy dump_gene_os_extrom.exe on your device. Insert SD-card with at least 70 MB free on it. Run copied program. After some time you will see message - Dump complit. On SD-card will be files os.nb and extrom.nb.
how to flash ?
use htc rom tool
click on build tab
device = gene
u see firmware contain on right
give path Ext. ROM to extrom.nb
OS to os.nb
click on build u get new file called ruu_signed.nbh
First of all, Hi!
Now, how do I clear my nike to the point where it has nothing on it?
I need to do this because I got stuck in the process of flashing it with HARDSPL 1.22 that I need in order to flash a new rom!
I tried everything, I followed the guide on how to do HardSpl, but got stuck at step 8 of the tutorial, the process bar is constantly at 0%, and followed by recovery steps!
I do not need them because everything works just fine, only with the original rom still on!
So I want to flash a rom, but am unable to!
Please help me!
Even if my solution is deleting everything ( I do not mean a Hard Reset- Did that 10 times ) and starting from 0!
But this is one thing I never did, and do not know where to start or what to do!
So any good soul out there willing to help, please do so!
Thanks in advance!
Ok let's try to help, can you tell us more details about your phone, model 16 or 20 keys, rom and radio.
If this is not clear just send me a pm
Regards Rataplan
Thanks, mine is a 16 key version.
Radio 1.65.28.25
Rom: 2.09.405.1
Rom date: 30.08.2008.
Protocol version: 25.98.40.07H
And I did the first few steps of flashing the HardSpl
and now it says SPL 1.22
and further more, on start up screen it says "TEST ONLY NOT FOR SALE"
BTW: I was looking of flashing your ROM but as I said, no can do!
HELP
Ok from what I see it looks to me that you already flashed a rom, just one question is it telling SPL 1.22 or SPL 1.22 Hard
just SPL
That is my problem!
Any solution!?
You need to start all over again, do you have a Niki, you can see that under the battery
Okay just read your post in the other thread, that cleared a lot of things, just do it all over again and use 1.15 instead of 1.22 maybe that will work for you, btw from what I can see you didn't do anything wrong, I also flashed directly the 1.22 and from me that works.
Just keep me informed how it goes.
Regards
The phone is niki100
There is no simlock!
What do I need to do?
Refer me to a tutorial, or just tell me everything here?
And thank you for the help so far!
Edit:
OK, I did what you said, and so far works!
But, could you please explain to me a couple of things!
1. download the attached files DONE
2. REMOVE SIM and SD CARDS !! DONE
3. connect usb cable DONE
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!) DONE
5. after a few seconds "USB" appears on the display DONE
6. unplug and replug the usb cable DONE
(OPTIONAL, better to skip it! step 7. if you only want to test the sspl try flashing the attached splash screen by running ROMUpdateUtility.exe from flash-splash-niki) SKIPPED
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki
AND NOW here is my question, in the file FLASH-USPL-NIKI there is a uspl-1.16-nike.nbh file, but here in this step it says to flesh the 1.15mfg(wich I downloaded), so do
i have to delete the 1.16 and replace it with the 1.15mfg or what?
9. after installing the hardspl you can flash any rom (rom cook project here)
Okay I think I kow what you mean, you must flash the 1.15mfg, do not copy it to your phone, you don't have to delete the 1.16.
EUREKA, it worked!
Flashed your F01-10 rom!
Now I only did the 1.15 HARD Spl
Please suggest to me a radio?
I tried flashing the Radio_1.71.09.01_25.75.40.02K and it got to 100% and then said FLASH WRITE ERROR, so I was stuck wit the old radio!
AND OMG, THE ROM IS WONDERFUL
Thank you so very very much!
I need help, i have flashed a rom but now my niki stops at the radio details. It doesn't boot to windows mobile.
How do i reflash a working rom now?
How long have you waited before taking out the battery?
It takes a while to load!
It takes a while to load yes, but 5-10 minutes is to long for it to start to boot.
It has passed 1 hour now.
Anyone knows how can i fix my niki?
2 die 4 said:
EUREKA, it worked!
Flashed your F01-10 rom!
Now I only did the 1.15 HARD Spl
Please suggest to me a radio?
I tried flashing the Radio_1.71.09.01_25.75.40.02K and it got to 100% and then said FLASH WRITE ERROR, so I was stuck wit the old radio!
AND OMG, THE ROM IS WONDERFUL
Thank you so very very much!
Click to expand...
Click to collapse
You're welcome for the rom, about the radio if you want to try the 1.71 radio you have to go back to an older radio before you flash the 1.71.
I suggest to use a 1.5.. radio, that will do the trick.
For now you can always put Hardspl 1.22 on your phone, some people are recommended that if you flash a wm 6.5 rom, personally I don't see any difference.
Btw The radio I use is 1.65.29.22
Regards
masterxiter said:
It has passed 1 hour now.
Anyone knows how can i fix my niki?
Click to expand...
Click to collapse
Hmm, that's a long time without a phone , did you already try a hardreset, just turn the phone off, and turn it on by pressing the power and the send and end key on the dame time, I think that will do it.
Just keep me informed.
Regards
Rataplan said:
Hmm, that's a long time without a phone , did you already try a hardreset, just turn the phone off, and turn it on by pressing the power and the send and end key on the dame time, I think that will do it.
Just keep me informed.
Regards
Click to expand...
Click to collapse
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
masterxiter said:
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
Click to expand...
Click to collapse
Hmm, okay this will be diffucult, I've read you flashed a rom and after that you get this issue, just a few questions did you cid unlock your phone, and is the bootloader still there. (that is the 4 coloured screen with the spl info)
masterxiter said:
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
Click to expand...
Click to collapse
hey dude
y dont u flash the original rom of htc nike once and then retry?
Rataplan said:
Hmm, okay this will be diffucult, I've read you flashed a rom and after that you get this issue, just a few questions did you cid unlock your phone, and is the bootloader still there. (that is the 4 coloured screen with the spl info)
Click to expand...
Click to collapse
Yes i have both.
I allready change those 4 colors for an image, lol but ok i have the spl info:
M 04
B 04
R 1.65.28.25
G 25.98.40.07W
D 2.12
What happened was, i had an working cooked rom flashed in my phone. I was working with it for about a month.
yesterday i flashed with another one. It got me 100% rebooted and voilla doesn't pass the spl boot.
masterxiter said:
Yes i have both.
I allready change those 4 colors for an image, lol but ok i have the spl info:
M 04 R 1.65.28.25
B 04 G 25.98.40.07W
D 2.12
Click to expand...
Click to collapse
Ha ha yeah that would be nice if we could replace that for an image.
Okay, connect it to your computer when you're on the 4 coloured screen and see if it connect then, in the phone you see serial changing in usb, if yes just flash your original rom.