Prophet Tools Light: Just the flash! - JAMin, XDA Neo, S200 ROM Development

I've seen lots of threads around asking for what to do etc... Read this thread if you're clueless (or stuck)!
Starting
To upgrade your devices ROM, you first need to prepare the SPL (Secondary Program Loader) to allow the new ROM to boot.
This can be done through JumpSPL/SoftSPL (temporary) or HardSPL (permanent). And can be undone by flashing a WM5 Official ROM from here.
Before you upgrade anything, you need to know whether your device is a G3 or a G4. To find out, read this
JumpSPL/SoftSPL
The idea behind "JumpSPL" is to temporarily make the bootloader load a new ROM/RUU. JumpSPL is not permanent, and will not damage the device if it goes wrong.
To use JumpSPL, download the "ProphetSPLTool" attached below, select the device you have (G3/G4) and click "JumpSPL". After that has run (your Prophet will have a white screen), you need to start the RUU for your ROM.
HardSPL
The idea behind "HardSPL" is to permanently make the bootloader load a new ROM/RUU. HardSPL is permanent, and will damage the device if it goes wrong.
To use HardSPL, download the "ProphetSPLTool" attached below, select the device you have (G3/G4) and click "HardSPL". After that has run (your Prophet will have restart), you need to start the RUU for your ROM.
The Flash!
Once you have prepared your devices SPL, you need to charge the battery to more than 50% (for safety!)
Using "ProphetToolsLight", the same functions as above will be applied, with the addition of the ROM flash being carried out.
You'll need to copy the ROM file (*.nbf) into \Utils\Flash, and then do Hard/Soft SPL as per above. Once that has done, another RUU will open up and flash the ROM! Simply hard reset after that, and you're done!
Recovery
If at any stage your Prophet fails to start properly or can only enter bootloader follow this:
Download and install the latest version of ActiveSync (Google for it)
Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from [here | ftp://xda:[email protected]/RUU_Prophet_220734_2207114_024721_NVID.exe] or [here | http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs]
Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
Plug the Prophet in via USB
Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder. If there is only one RUU, use that.
When it has finished: disconnect the Prophet, and then re-enable the connect through USB in actyivesync before reconnecting the device.
Your Prophet should now work!
Notes:
* It doesn't matter if you can't sync files, so long as when you plug the device in it says "USB" in the bottom right hand corner of the screen.
* XP must be used if your device is a G4 (Vista may work for G3 devices but I'm not sure).
Download
ProphetSPLTool.zip - 4.77 Mb
ProphetToolsLight.zip - 3.16 Mb

Screen Shots:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

this should be sticky too...
l3v5y: you're always encouraging,cooperative and helpful at this forum, special thanks from me...

Danke
vielen Dank

This is realy usefull!!
My compliments for the efford, I agree on your contribution to this community.

rondol1 said:
This is realy usefull!!
My compliments for the efford, I agree on your contribution to this community.
Click to expand...
Click to collapse
Thanks!

HardSPL problem, stuck in boot loader with fail hardSPL
hey guys,, I did a foolish thing and now i'm stuck!!!
I did the HardSPL thing(apparently wrong!!)
and then i started using RUU flashig the new rom
so now from my SPL on the boot screen i get that the hardSPL didn’t function, and its stuck in boot loader with old SPL
and now that i've flashed the new rom, i cant hardSPL again,,,,
I'm so stuck,
i guess i can flash AKU 2.2 and then hardSPL again,
does it gonna work?
is there anyyyything i can do?
plzzzzzzz help :
IPL 2.20.0001
SPL 2.20.0001

STOP POSTING EVERYWHERE MAN~~~~~
(server problem, dupl. posted )

thom_yorke said:
hey guys,, I did a foolish thing and now i'm stuck!!!
I did the HardSPL thing(apparently wrong!!)
and then i started using RUU flashig the new rom
so now from my SPL on the boot screen i get that the hardSPL didn’t function, and its stuck in boot loader with old SPL
and now that i've flashed the new rom, i cant hardSPL again,,,,
I'm so stuck,
i guess i can flash AKU 2.2 and then hardSPL again,
does it gonna work?
is there anyyyything i can do?
plzzzzzzz help
IPL 2.20.0001
SPL 2.20.0001
Click to expand...
Click to collapse
........
STOP POSTING EVERYWHERE MAN~~~~~
( I do hope that yours is not a G3)

soryy,
no it's G4,
Im just a little freaked OUT!!!
its not hardSPL yet right?
i spend a week reading these articles, and yet i ,,,, !
what can i do?!
sorry again 4 that,

...mkay, regardless of which version of prophet tools i'm using (normal or lite), its my understanding that i have to place the .nbf file into the "\Utils\Flash" directory... But where exactly is that? on my local disk, desktop, prophet tools installation folder...?
I've tried installing a number of ROMs, all of which have failed except a Crossbow PDAViet ROM which is only slightly better than the standard i was running before (no WM6 gui...) Any ideas why that is?
Please advise, and thanks in advance.
G4 Prophet
Dopod 818pro
PDAViet 4.0.0.0.5 Crossbow ROM
(not what i expected!lol)

i also noticed that with the Crossbow ROM, my prophet isn't detected on my vista machine where it was before the slight upgrade. Does this mean that all "new" roms will require me to use xp after a prophet upgrade...?

AZUbius said:
...mkay, regardless of which version of prophet tools i'm using (normal or lite), its my understanding that i have to place the .nbf file into the "\Utils\Flash" directory... But where exactly is that? on my local disk, desktop, prophet tools installation folder...?
I've tried installing a number of ROMs, all of which have failed except a Crossbow PDAViet ROM which is only slightly better than the standard i was running before (no WM6 gui...) Any ideas why that is?
Please advise, and thanks in advance.
G4 Prophet
Dopod 818pro
PDAViet 4.0.0.0.5 Crossbow ROM
(not what i expected!lol)
Click to expand...
Click to collapse
If you unzip the file to somewhere (desktop may be simplest) you'll need to copy the *.nbf to %INSTALLDIR%\Utils\Flash.

AZUbius said:
i also noticed that with the Crossbow ROM, my prophet isn't detected on my vista machine where it was before the slight upgrade. Does this mean that all "new" roms will require me to use xp after a prophet upgrade...?
Click to expand...
Click to collapse
New ROMs should be detected under Vista, but flashing must be done under XP.

Flashing to WM6
Hi guys,
I am a Newbie who has just bought an M600 off ebay last night (so I don't know if its a G3 or G4 yet) and I am thinking about upgrading to WM6. I would like to follow this guide as it looks simple and I think that I could follow it.
However I have a few questions:
1)You mention using the SPL tool to prepare the SPL using SoftSPL or HardSPL but this seems to be the first thing that prophet tools light does. So can I perform the entire operation via Prophet tools light or do I need to use ProphetSPLTool first and then after the SPL is done switch to ProphetToolsLight? If I can why did is ProphetSPLTool mentioned in the guide.
2) How likely is it that I brick my M600 by doing this, as I would really really hate to brick it? Could it just randomly brick or would I need to do something very stupid to induce it? And is there anything not in this guide that you should tell me about?
3) Can I use this same tool to change the WM6 rom that I am using (i.e go from a WM6 platform to another WM6 platform)? and if I decide that I dont like WM6 can I use this same tool to restore it to the original orange WM5 rom (i.e WM6 to WM5). I I need a differant tool please could you point me in the right direction.
4) I will either be using Cloudyfa's '[WM6.1] Prophet ShadoW 2.0 TE' or the 'Prophet S4V.19701.01 (UC)' ROM. I assume these are compatible with this tool.
5) Also two very small things. Firstly some ROMs claim to be UC compatible what does this actually mean.
Thank you for your patience with a newbie and any help is appreciated.
-josh

Not a valid Win32 app
I tried the softSPL.exe for my G4 S200 and got the "Not a valid Win32 application" warning. Any suggestions as to what to do next?
Thanks, Ron M.

josh92176 said:
Hi guys,
I am a Newbie who has just bought an M600 off ebay last night (so I don't know if its a G3 or G4 yet) and I am thinking about upgrading to WM6. I would like to follow this guide as it looks simple and I think that I could follow it.
However I have a few questions:
1)You mention using the SPL tool to prepare the SPL using SoftSPL or HardSPL but this seems to be the first thing that prophet tools light does. So can I perform the entire operation via Prophet tools light or do I need to use ProphetSPLTool first and then after the SPL is done switch to ProphetToolsLight? If I can why did is ProphetSPLTool mentioned in the guide.
2) How likely is it that I brick my M600 by doing this, as I would really really hate to brick it? Could it just randomly brick or would I need to do something very stupid to induce it? And is there anything not in this guide that you should tell me about?
3) Can I use this same tool to change the WM6 rom that I am using (i.e go from a WM6 platform to another WM6 platform)? and if I decide that I dont like WM6 can I use this same tool to restore it to the original orange WM5 rom (i.e WM6 to WM5). I I need a differant tool please could you point me in the right direction.
4) I will either be using Cloudyfa's '[WM6.1] Prophet ShadoW 2.0 TE' or the 'Prophet S4V.19701.01 (UC)' ROM. I assume these are compatible with this tool.
5) Also two very small things. Firstly some ROMs claim to be UC compatible what does this actually mean.
Thank you for your patience with a newbie and any help is appreciated.
-josh
Click to expand...
Click to collapse
Just use Prophet Tools Light, and use the "SoftSPL" option. This cannot brick your device unless the ROM contains an SPL (which cloudyfas do not), Hard SPL can brick your device if you pick the wrong SPL, but other than that should not.
This tool can be used to flash from any ROM to any ROM (for Prophet only),
For recovery, I'd try and use the original RUUs as they are un altered, and will have the least chance of failure.
UC means "User Customization". Look at the original thread here.
Cloudyfas 19701 ROM may have some issues with the SPV M600 SIM unlock, but Prophet ShadoW does not...
Welcome to the world of Prophets!

ronm said:
I tried the softSPL.exe for my G4 S200 and got the "Not a valid Win32 application" warning. Any suggestions as to what to do next?
Thanks, Ron M.
Click to expand...
Click to collapse
Wrong exe! The "Prophet Tools Light" (maybe called "SPLTool" or similar) is the one you must run!

l3v5y said:
Just use Prophet Tools Light, and use the "SoftSPL" option. This cannot brick your device unless the ROM contains an SPL (which cloudyfas do not), Hard SPL can brick your device if you pick the wrong SPL, but other than that should not.
This tool can be used to flash from any ROM to any ROM (for Prophet only),
For recovery, I'd try and use the original RUUs as they are un altered, and will have the least chance of failure.
UC means "User Customization". Look at the original thread here.
Cloudyfas 19701 ROM may have some issues with the SPV M600 SIM unlock, but Prophet ShadoW does not...
Welcome to the world of Prophets!
Click to expand...
Click to collapse
Thanks very much I took the plunge and it was much less painless than I thought that it would be. I am now running prophet shadow v.2 and it all works excellently. Thank you for the advice.
-josh

Error [238] : File read
Hi,
I followed the instructions, copied the nk.nbf file to the utils/flash directory but it seems that the rom flash program can not find the *.nbf file. The error is: "Error [238] : File read".
Is the nk.nbf the correct file name?
Do I need to copy more files?
Thanks

Related

WM6 Upgrade Guide

How to upgrade from WM5 TO WM6
To upgrade your prophet to WM6 I recommend that you first of all downgrade to the NVID version of WM5 AKU2.2 and get the latest Active Sync:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe YOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com
3. Install active sync, you might need to reboot
4. When your computer has rebooted, run the file from step No 1 . Follow the steps, remember that it can take some time and seem to stuck at 80% and higher, but just wait.
5. When you have done this, your pda will reboot. After it comes with the welcome to windows mobile screen,"Tap Here To Begin",JUST LEAVE IT. In fact don't touch your device before the next steps are finished.
6. Now download one of the WM6 versions( http://forum.xda-developers.com/showpost.php?p=1279985&postcount=1 )
7. Now find a file named Upgrade.bat,and run it.(you don't have to run Step1 of PdaMobiz or PDAViet Temp,as you have already downgraded to AKU2.2)
8. Wait until the upgrade finishes(usually takes 12-15minutes)..WAIT WAIT WAIT
9. A message will be displayed in the dos box,and it will say that the upgrade is finished etc....etc...,now you HAVE to HARD RESET,to finish the upgrade and enjoy you new WM6!
How to downgrade from WM6 TO WM5
The downgrade process from WM6 to WM5 is pretty simple. All you have to do is to downgrade to WM5 NVID and after that upgrade to the WM5 you want:
1. Download the NVID(no vendor) AKU 2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exeYOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com.. Simply search for "Active Sync"
3. Install active sync, you might need to reboot
4. When your PC is ready run the NVID file you downloaded in step1 and follow the guide, remember that it can take some time and seem to stuck at 80% and higher, but just wait
5. When its done downgrading to the NVID WM5 rom, you prophet will reset and you can upgrade to the version of WM5 you want.
NOTICE
If you use a different AKU 2.2 ROM(like PDAViet Temp),you may have two EXEs in the folder you extracted.Be careful and use the one that is made for your device:
FILENAME G3.EXE
is for G3 devices:IPL x.xx.0000, SPL x.xx.000.0 (this is shown when you reset)
FILENAME G4.EXE
is for G4 devices:IPL x.xx.0001, SPL x.xx.000.1 (this is shown when you reset)
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
How to switch or upgrade/downgrade between WM6 versions(for example PDAViet->Trueneytral)
1. First you have to downgrade to WM5 AKU2.2 using the WM6->WM5 guide(some say that you don't have to do that,but i believe that it's better to downgrade first rather than making a simple overwrite)
2. Now follow STEP 5 of the WM5->WM6 guide
Device doesn't connect to PC after flash
If your device doesn't connect to your PC after flash,just enter bootloader(press camera button+while pressing soft reset and hold,until a tri-color screen shows up),and flash the NoVendor WM5 Rom: http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe .Then repeat the whole process...
----------------------------------------------------------
KEEP IN MIND:
UPGRADING CAN BE DANGEROUS,YOU ARE RESPONSIBLE FOR THE DAMAGE TO YOUR PHONE
DO NOT RESTORE BACKUPS FROM ANY ROM OTHER THAN THE ONE IT WAS CREATED ON
THERE IS NO "BEST WM6 ROM",THE BEST IS THE ONE THAT WORKS BEST FOR YOU
(part of the guide is taken from Da9L's guide,in the WM6 Rom Collection)
I will edit/update this post soon and clean it up, ask questions in another thread, and by god please read the wiki first, 90% of the questions asked are answered in the wiki....
WM6 Upgrade Guide...reply
great info sir! thanks so much! downloading...i'll be happy to send feedbacks on this WM6 ROM! thanks again!
Thanx a lot tonydeli7 , very very good guide and a lot of ppl really needed it
Great
Thanks to you all. I have Qtek S200 and trobuled with WM6 it wonderfull guide for me thank you very much.
I need to downgrade to WM5, 'couse I cannot boot anymore. After running the setup I get an error that the device cannot be found. I have connected the S200 with the boot loader running.
Edit: Now it works on an "old" WinXP machine.
Huge Problem!!
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
dharvey4651 said:
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
Click to expand...
Click to collapse
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
I followed the instructions carefully, and my phone (Qtek S200) seemed to boot with WM6.0
However, after aligning screen, it tried to initialize the phone with some extended roms, a procedure which failed, and I had to soft reset.
After reboot, it seems to work fine.
Is it?
EDIT: Another thing I noticed is that keyboard is in THAI !!! How can I make US the default? Olso, I have Resco keyboard GR edition. Will this work with WM6?
tonydeli7 said:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Click to expand...
Click to collapse
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
yoda_143 said:
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
Click to expand...
Click to collapse
i don't know mate.i believe you can use pdaviet's temp instead of aku2.2 nvid...
Another thing I noticed, is that it looses pairing with my bt handsfree...
I am making the pairing, and works fine. However, when at night I am shutting off my hf in order to save battery, the next morning the pairing is gone.
Any solution to this?
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
dufchan said:
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
Click to expand...
Click to collapse
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
I-mate Jamin
hello evrybody
i just wanted to know if i can upgrate my WM5 to WM6 on my I-mate JAMin?
rondol1 said:
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
Click to expand...
Click to collapse
thank u very much!!now my dopod working fine!!thanks a lot!!
thanx for the guide
help me please..
P4k1t0 said:
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
Click to expand...
Click to collapse
how to do that?
thx..
Choice of ROM
Hello guys, tanks for a so nice job !
I would like to have more information about the choice of ROM.
I don't want any special feature, just the row wm6.
no programs added, no tweaky today, no bugs, no battery problem, etc etc
which one would fit that the best ?
thanks
Thnx for this man, much appreciated!

[Solution] G4 Hard SPL (CID unlock)

The G4 soft-SPL is working great, and some people already have used our hard SPL for some time now.
FAQ:
What is Hard SPL?
- a custom G4 SPL patched by Olipro which let your device thing it has SuperCID (aka CID unlocked)
What is different to the Soft SPL?
-Soft SPL is temporarily, this solution is semi permanent, it will be removed by flashing an original G4 SPL.
-You don't need a separate loader in the future, just use the RUU provided in the ROM package.
Can I use it for other devices than for a G4 wizard?
G4 Wizards only, use at own risk
Usage:
-connect your device
-Start hard_SPL-G4.exe
-Push the "Check DOC" button
-> The tool now checks whether your device is truly a G4, if not, it will give you an error and stops.
-> after this a dos box pops up, and it loads the softSPL to your device, to enable hard-SPL flashing.
-> then a Rom Update Utility will start, ONLY proceed if your screen is white!
-Proceed with the upgrade, it will only take a minute.
After reboot the IPL version is : 2.21.0001 and the SPL is 2.21.olip
Now you have Hard SPL
You can flash the ROMs with the RUU in the ROM package, should you have trouble with upgrading, try Mun's RUU (thanks for the tip Boto).
So no need to downgrade before upgrade anymore.
But don't flash ROMs containing IPL/SPL.
If you got the following error:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
You didn't read the thread, and you may thank mestrini for his detection tool, otherwise your device would be a brick.
Thanks to Mestrini, who made the DOC checker so that only G4 can be flashed, and G3's can't, thus saving them from certain death!
Thanks to Olipro who patched the G4 SPL
Thanks to DES and Pof, from whom I took the idea and and some of the scripts.
Thanks to SAA044 who beta tested all the sSPL and hard SPL versions, and lost a wizard in the process, but kept his head cool, and kept on testing with his brand new wizard, respect to you, and thanks my friend!
Thanks to all I didn't mention but had an input in this project.
You can download the hardSPL from here HERE or here.
[edit]26-09-'07 02:00 repacked the Hard SPL, it seems that the first package method caused some problems.[/edit]
Post Script (09th Oct. '07)
As I have mentioned before in this post:
You shouldn't try to update ROM's with IPL/SPL after HARD SPL.
BUT: If you want to update IPL/SPL for G4 after hard SPL, do as following:
-disassemble ROM with IPL/SPL of your liking
Usage: typho5.exe -x nk.nbf
-reassemble the ROM or IPL/SPL with NKnbftool.
Make shure you only use G4 IPL/SPL for your G4, those are the IPL_2 and SPL_2 files created by typho5.exe.
-copy the nk.nbf you just created to SOFT SPL Folder
-start Soft SPL and flash the IPL/SPL.
You will lose the hardSPL though!
Typho5.exe and nknbftool are available in most kitchens.
The new WST also has some nice features to strip a ROM.
[updated 07.10.07]
dharvey4651 wrote a tutorial on how to Remove the Hard-SPL
Yes come on you lazy bums, I tested the spl for all of you and bricked my 1st k-jam, I donated the first and only blocks. So if you guys expect more magic its time to give back a little.
Unfortunatelly I´m on windows Vista and it does not seems to work quite allright with Wizard Service Tool...
Anyway, as I get home tonight I will use my wife´s computer (if she doesn´t find me messing around again with the new cellphone...) and will try to get you another CID lock...
Ok.
no need to bug my wife... Actually it seems that the CID Block downloading from Wizard Service Tool works just fine unde Windows vista. I´ve downloaded mine and have already e-mailed it to Mestrini...
danielvelez said:
Unfortunatelly I´m on windows Vista and it does not seems to work quite allright with Wizard Service Tool...
Anyway, as I get home tonight I will use my wife´s computer (if she doesn´t find me messing around again with the new cellphone...) and will try to get you another CID lock...
Click to expand...
Click to collapse
That is the spirit.
Thanks bro
the-equinoxe said:
The G4 soft-SPL is working great, and some people already have used our hard SPL for some time now.
Faq.
What is Hard SPL?
- a custom G4 SPL patched by Olipro which let your device thing it has SuperCID (aka CID unlocked)
What is different to the Soft SPL?
-Soft SPL is temporarily, this solution is semi permanent, it will be removed by flashing an original G4 SPL.
-You don't need a separate loader in the future, just use the RUU provided in the ROM package.
Can I use it for other devices than for a G4 wizard?
G4 Wizards only
Usage:
-connect your device
-Start hard_SPL-G4.exe
-Push the "Check DOC" button
-> The tool now checks whether your device is truly a G4, if not, it will give you an error and stops.
-> after this a dos box pops up, and it loads the softSPL to your device, to enable hard-SPL flashing.
-> then a Rom Update Utility will start, ONLY proceed if your screen is white!
-Proceed with the upgrade, it will only take a minute.
After reboot the IPL version is : 2.21.0001 and the SPL is 2.21.olip
Now you have Hard SPL
Thanks to Mestrini, who made the DOC checker so that only G4 can be flashed, and G3's can't, thus saving them from certain death!
Thanks To Olipro who patched the G4 SPL
Thanks to DES and Pof, from whom I took the idea and and some of the scripts.
[attachments are not yet uploaded]
Hard SPL is not yet uploaded
We have decided to hold back the Hard SPL for a little while:
-Since the release of the Soft SPL over 850 people downloaded it, however nobody felt obliged to give something back to the community .
In my signature I have been asking to share your CID block with Mestrini, so he can finish his free solution for the "data crashes error".
However, (apart from a single soul) nobody cared, and nobody shared.
This saddens me, Our community is here to help each other, you are all shouting for solutions, but no-one is helping..
To emphasize things:
All the people working on this G4 project DON'T OWN A G4, soft SPL and HARD SPL where brought to you by G3 owners, our beta tester even bricked one while testing. So we didn't have any gain in this free tool!
Hard SPL will be released as soon as mestrini has his 100 CID blocks, he now only has 53 (and 40 were donated by a SINGLE user!!)
The request was first posted on may the 17th..
That summons up the community spirit a bit.
So share now:
[*]Get Wizard Service Tool (LINK) and use the "Read ROM" button to read the CID area, and contact mestrini so he can get the CID block.
All posting regarding CID block/data crashes error have to be posted here
Click to expand...
Click to collapse
Questions:
- After hard-SSPL I´m guessing that you get your softspl flashed... so the following flashes are supposed to be also with the white screen using the default rru? or should they go to the three color screen bootloader but with another SPL version (olip one)?
- And If your IPL is different, say 2.26.0001 It will actually change to 2.21.0001?
- And does the 2.21 SPL means that you now have a G4 IPL and a G3 SPL?
- Would you be able to flash a rom that has IPL or SPL, or you should keep away from those as usual?
danielvelez said:
- And If your IPL is different, say 2.26.0001 It will actually change to 2.21.0001?
- And does the 2.21 SPL means that you now have a G4 IPL and a G3 SPL?
- Would you be able to flash a rom that has IPL or SPL, or you should keep away from those as usual?
Click to expand...
Click to collapse
If I recall rightly, I blocked SPL flashing.
I only seen this thread right now. I have already the HardSPL done, will the CID Block reading still help mestrini?
Edit: I've sent him my readings Sorry I didn't noticed this earlier... I've got an Key index 80, which he doesn't have any
Sent key block, just curious what if all 100 keys aren't actually in the wild? Just a thought... (I already have unlocked G4 from IMEI-check so I'm not after this, I was just curious).
neonkoala said:
Sent key block, just curious what if all 100 keys aren't actually in the wild? Just a thought... (I already have unlocked G4 from IMEI-check so I'm not after this, I was just curious).
Click to expand...
Click to collapse
If there aren't 100 in the wild than those unreleased aren't necessary
Thanks for your contribution
heheh i already send my a long time ago...
i never understand why anyone help mestrini!!!
now you find a good way for that!!
waiting for the hard SPL!!
see you =]
Updated first post
Olipro said:
If I recall rightly, I blocked SPL flashing.
Click to expand...
Click to collapse
Sorry I did not quite get it... You are saying that after using hard SPL, you won´t be able to re-flash any SPL on the phone as it get´s blocked? So if you try a rom with SPL on it you wont need to worry about it as it wont flash the spl, so impossible to brick the G4 if accidentally flashing a G3 rom?
As i understand the bricking issue comes only for flashing a g3 spl into a g4...
And also i´m still curious about the hard-spl version, with only 2.21 olip:
"olip" standing for the 0000 after the 21 meaning it still a g4 spl or meaning that you now have a working g3 spl on a g4 device?
danielvelez said:
Sorry I did not quite get it... You are saying that after using hard SPL, you won´t be able to re-flash any SPL on the phone as it get´s blocked? So if you try a rom with SPL on it you wont need to worry about it as it wont flash the spl, so impossible to brick the G4 if accidentally flashing a G3 rom?
As i understand the bricking issue comes only for flashing a g3 spl into a g4...
And also i´m still curious about the hard-spl version, with only 2.21 olip:
"olip" standing for the 0000 after the 21 meaning it still a g4 spl or meaning that you now have a working g3 spl on a g4 device?
Click to expand...
Click to collapse
Be careful SPL flashing is still possible.
Soft SPL also allows spl flashing! And soft SPL is the same thing only temporary, so be carefull.
The hard SPL is a full flown G4 SPL, but marked 2.21.olip instead of 2.212.0001 so you can see that a patched SPL is on the device.
argggg i cant donwload it!!
site is full of leech!!
i dont know what hapen, but when soft spl start
the screen close and ruu dont start to proced...=/
boto said:
argggg i cant donwload it!!
site is full of lech!!
Click to expand...
Click to collapse
Lech ??
Please explain.
hehe leech, download at same time..
or link is not soooo good..
but now i donwload it...
man..can you please try to help me? everytime that i start the unlock when the soft spl start the prompt close on 20%
i always use the softspl to flash roms without problem.
_________
Ok, i think i find a solution, i extract the .exe file...
looks the temp folder cause this problem
boto said:
hehe leech, download at same time..
or link is not soooo good..
but now i donwload it...
man..can you please try to help me? everytime that i start the unlock when the soft spl start the prompt close on 20%
i always use the softspl to flash roms without problem.
Click to expand...
Click to collapse
You can extract the hard spl exe.
We only added the doc checker to start the soft spl.
ok...
now i dont get the white screen, only a pinguim ;P like kernel boot screen
i will try again...
___
One more try and now white screen!! let see how will work...prey for me!
Result: my ruu dont find a connection....3 try...
_______________________
boto said:
ok...
now i dont get the white screen, only a pinguim ;P like kernel boot screen
i will try again...
Click to expand...
Click to collapse
If you are shure you have a G4 (to explain for everybody), you can use the nk.nbf with the original Soft SPL.
We only added the DOC checker, so G3 users are warned.

Please help me (sos)

Hi
My phone is I-mate k-jam (kind of G4).I unlocked my phone’s CID by hard SPL program from your website . I could not install phone’s original rom. Then I installed original rom by shelltools program. My phone is not operated after hard resetting. When I switch on my phone, it stopped in three-colored page. Please be kind enough to conduct me.
You need to remove the hard spl in order to go back to the original rom
http://forum.xda-developers.com/showthread.php?t=342744
randomgoon said:
You need to remove the hard spl in order to go back to the original rom
http://forum.xda-developers.com/showthread.php?t=342744
Click to expand...
Click to collapse
START-sSPL.exe error : no device connected please help
http://www.htcamerica.net/support/8125/software-downloads.html
I ran that just fine with HardSPL installed
LancerV said:
http://www.htcamerica.net/support/8125/software-downloads.html
I ran that just fine with HardSPL installed
Click to expand...
Click to collapse
is not installed
error [294] : invalid vender id
please help
@behzad_sedat
What is the SPL version?
Invalid Vendor ID means it's not CID unlocked..
So you need the original i-mate ROM obviously. Not the HTC/Qtek ROM..
BTW.: Soft SPL doesn't work in bootloader, it needs WM 5/6 in order to load the Soft SPL.
Connect USB cable, kill wscecomm.exe (in PC's taskmanager) and start the RUU.
Forget the warning the Ruu tells you about having an active activesync connection. Flash the original iMate ROM.
the-equinoxe said:
@behzad_sedat
What is the SPL version?
Invalid Vendor ID means it's not CID unlocked..
So you need the original i-mate ROM obviously. Not the HTC/Qtek ROM..
BTW.: Soft SPL doesn't work in bootloader, it needs WM 5/6 in order to load the Soft SPL.
Connect USB cable, kill wscecomm.exe (in PC's taskmanager) and start the RUU.
Forget the warning the Ruu tells you about having an active activesync connection. Flash the original iMate ROM.
Click to expand...
Click to collapse
hi
i installed K-JAM_Arabic_2160901_21609102_20710_ship.exe
error : [296] : upgrade only
this nbf file cannot be use for your pda phone. please get newer nbf file help please please
the-equinoxe said:
@behzad_sedat
What is the SPL version?
Invalid Vendor ID means it's not CID unlocked..
So you need the original i-mate ROM obviously. Not the HTC/Qtek ROM..
BTW.: Soft SPL doesn't work in bootloader, it needs WM 5/6 in order to load the Soft SPL.
Connect USB cable, kill wscecomm.exe (in PC's taskmanager) and start the RUU.
Forget the warning the Ruu tells you about having an active activesync connection. Flash the original iMate ROM.
Click to expand...
Click to collapse
ipl : 2.17.0001
spl : 2.17.0001
behzad_sedat said:
ipl : 2.17.0001
spl : 2.17.0001
Click to expand...
Click to collapse
You haven't got Hard SPL.
So only way to flash is original ROM (in original Language it came with).
the-equinoxe said:
You haven't got Hard SPL.
So only way to flash is original ROM (in original Language it came with).
Click to expand...
Click to collapse
Dear Sir
I explain my problem more accurat. I downloaded Soft SPL accompanied by Vodafone Qtek 9100 G4 IPl&SPL.zip after reading topic of How To Remove HardSPL and according teaching I transferred nk.nbf file from Vodafone Qtek 9100 G4 IPl&SPL.zip file to Soft SPL file .Then I wanted to perform Start-sSPL.exe file but I could not perform. Then I found Soft SPL is not operated in Bootloader.Then I performed 2.exe (ROMUpdateUtility MFC Application) file in Soft SPL file accidentally. I thought it is being installed. After accomplishment I found my phone’s spl has turned from olip to 2.17.0001.So I wanted to install original ram but I couldn’t install. It is installed wm6 on my phone completely now but it is stopped in spl page. I think I could not remove my phone’s hard spl completely. Please be kind enough to help me.
behzad_sedat said:
Dear Sir
I explain my problem more accurat. I downloaded Soft SPL accompanied by Vodafone Qtek 9100 G4 IPl&SPL.zip after reading topic of How To Remove HardSPL and according teaching I transferred nk.nbf file from Vodafone Qtek 9100 G4 IPl&SPL.zip file to Soft SPL file .Then I wanted to perform Start-sSPL.exe file but I could not perform. Then I found Soft SPL is not operated in Bootloader.Then I performed 2.exe (ROMUpdateUtility MFC Application) file in Soft SPL file accidentally. I thought it is being installed. After accomplishment I found my phone’s spl has turned from olip to 2.17.0001.So I wanted to install original ram but I couldn’t install. It is installed wm6 on my phone completely now but it is stopped in spl page. I think I could not remove my phone’s hard spl completely. Please be kind enough to help me.
Click to expand...
Click to collapse
tyr the ,wizard love, rom did the trick for me
bill4676 said:
tyr the ,wizard love, rom did the trick for me
Click to expand...
Click to collapse
i cant download wizard love rom
You have requested http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar (54413 KB).
You have reached the download-limit for free-users. Want to download more?
Get your own Premium-account now! Instant download-access! (Or wait 92 minutes)
lol.. Wait 92 minutes then
bill4676 said:
tyr the ,wizard love, rom did the trick for me
Click to expand...
Click to collapse
Dear Sir
I installed rom of wizard love and my phone is operated.
Thank all of you

SIMPLY & COMPLETLY STUCK - plz help can't update to any ROM unless NVID...

Simply stuck and wandering...
Hi there
I am a noob in this area. I am reading the forum for the last days and trying to upgrade my i-mate jamin G3 but i always get stuck...
I started this thread as it involves more than one thread I read, namely
- Windows Mobile 6 Directory For Dummies
- New WM6 Upgrade Guide
- HardSPL guide and files
- Prophet Tools Light: Just the flash! & Prophet Tools: Simplify Flashing--V2.8.3 now up!
- Current upgrade guide for the most ROMs
- LAZYTOOL For all nk.nbf FLASHING + 3 color bootup SOLUTION + (PLEASE READ.........)
- WM 6.5 build 21501 Titanium [ Fixed ] & Fixed CommManager, and other ROMs I tryed...
- ...
so here it goes:
#1# I tryed to run HardSPL an I got an error message like this:
'One or more CON code pages invalid for your given keyboard'
so i guess i didn't work...
#2# then I tryed with ProphetTools and after doing the HardSPL it asks (in jamin) to run JumpSPL I click on yes and then I get white screen (in jamin) I click the flash rom and then I get either:
- error 260 or 274 - connection - this sometimes is worked around and got to 208
or/then
- error 208 - file open (and I did put the nk.nbf rom file in ...\Tools (as said on PTL) and also tryed in ...\Utils\Flash)
#3# While in white screen (achieved with PTL) I also tryed ROM 21501 (with its own RUU) and I get 3 colour screen after supposedly successful upgrade...
#4# also tryed lazyTool but got the same 3 colour screen
#5# With the no vendor NVID_RUU (got from lazy tool thread) I got it back to WM5 and working, pitfully i forgot to dump my original rom so now i am stuck in WM5 in English (i at least had it in Portuguese - my native L)...
I found this comment from dioxda2 in another thread...
Quote:
dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
... actually my prophet (jamin) works fine after I flashed the NVID, the problem is that I can't put it to work with any other ROM...
So any of senior experts plz advice
hopefully i am missing some supidly simple solution
#6# Meanwhile if someone knows were do download a original PTG ROM for prophet I would appreciate.
MYG
Jamin G3 unlocked
IPL 2.13
SPL 2.20
NVID
Last edited by MYGene; Today at 06:20 PM.. Reason: confused with dioxda2 comment...
my prophet is G4 so slightly different i would ask you to post detail for the second boot screen
here is mine
IPL 2.10.001
SPL 2.G4.4PDA
GSM 02.19.21
wapvirus said:
my prophet is G4 so slightly different i would ask you to post detail for the second boot screen
Click to expand...
Click to collapse
My SPL only shows:
IPL 2.13
SPL 2.20
im a total noob here too but i never encountered the same prob as you have.. i see SPL 2.20 right... so if you want to flash a ROM from here its required that you do HardSPL. i have a G3 device too. you might want to try this... i will try to help as much as i can...
make sure your USB cable/cradle is working perfectly and try to attached it at the back of your PC CPU...
and btw are you using XP or VISTA? coz i use XP...
just RUN HardSPL and let it do its thing... when its done check your SPL again..
marekPLPH said:
im a total noob here too but i never encountered the same prob as you have.. i see SPL 2.20 right... so if you want to flash a ROM from here its required that you do HardSPL. i have a G3 device too. you might want to try this... i will try to help as much as i can...
make sure your USB cable/cradle is working perfectly and try to attached it at the back of your PC CPU...
and btw are you using XP or VISTA? coz i use XP...
just RUN HardSPL and let it do its thing... when its done check your SPL again..
Click to expand...
Click to collapse
I just got another USB cable borrowed and tried the HardSPL you uploaded and it Worked
Actually It gave me the same error message about 'One or more CON code pages invalid for your given keyboard' but this time I didn't got the 3colour screen at the end, instead it restarted normally with SPL 2.G3
I am just waiting battery charge reaches 50% to try flashing it
Many thanks
(I assume either i got a corrupted HardSPL file either a bad USB cable...)
MYGene said:
I just got another USB cable borrowed and tried the HardSPL you uploaded and it Worked
Actually It gave me the same error message about 'One or more CON code pages invalid for your given keyboard' but this time I didn't got the 3colour screen at the end, instead it restarted normally with SPL 2.G3
I am just waiting battery charge reaches 50% to try flashing it
Many thanks
(I assume either i got a corrupted HardSPL file either a bad USB cable...)
Click to expand...
Click to collapse
Good to hear this...
Happy Flashing!!!
MYGene said:
I just got another USB cable borrowed and tried the HardSPL you uploaded and it Worked
Actually It gave me the same error message about 'One or more CON code pages invalid for your given keyboard' but this time I didn't got the 3colour screen at the end, instead it restarted normally with SPL 2.G3
I am just waiting battery charge reaches 50% to try flashing it
Many thanks
(I assume either i got a corrupted HardSPL file either a bad USB cable...)
Click to expand...
Click to collapse
That,s great news and happy flashing

New to Touch2 ROMs? Read this first please.

This post is supposed to help everyone who is new to Touch2, or at least new to Touch2 custom ROMs, and ROM flashing in general. If you have answers very to very general questions that might be missing here, please let me know in a reply. (Maybe this will eventually end up in the Wiki as well, there is no Touch2 section as of now)
1. What devices is this part of the XDA-Developers forum about?
This Area is all about the HTC Touch2. HTC's code name for it is MEGA. It also has a model number, which is T3333. Here is the specification at the HTC website. It looks like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Beware: There are other devices with similar names, like for example Touch PRO2 or Touch Dual. These are different devices, and have their own forums. Please do NOT use anything from the Touch2 for those other devices, it may "brick" (destroy) your device.
2. How do I identify my Touch2
First of all: If it doesn't look exactly like the picture above, it is not a Touch2. To be sure, shut down your device, open the rear cover, remove the battery. There it should say HTC Touch2 T3333.
You can also check on your device in System - Device Information - Identity. The Model No. should be HTC Touch2 T3333.
3. Touch2 Special Edition / T3320 / India Model
There is a Special Edition of the Touch2 with the Model Number T3320. It seems to be sold mainly in India, and does not have GPS or 3G (just GSM). It seems the Touch2 ROMs work OK (after HardSPL, see below) on both models, with GPS and 3G obviously not working on the T3320.
4. Why would I care about changing my ROM?
There are many reasons, but here are some of the most relevant:
- If you want a different language (some ROMs have selectable languages, but many don't, and officially you can not change the language of your device)
- If you want to have the newest Windows Mobile 6.5.5 instead of the standard 6.5
- If you want a "light" ROM, with many applications etc. removed, but more space
- If you enjoy tweaking your device, playing with it, etc.
Note: If you are fine with English as the language, but need a special keyboard and support for special characters for example in SMS, then there might not be a need for flashing another ROM. For example Arabic and Russian input is available here for install. No new ROM and no HardSPL necessary, changes can be undone by hard resetting. Other languages might be available as well, please search this forum.
5. What's the risk in changing my ROM?
First of all you have a little risk of bricking (destroying) your device when you do the HardSPL (see below what that is). When flashing ROMs there should be very little risk involved. You can also always go back to the original ROMs. If your ROM language/version (T-Mobile etc.) is not available for download (see this thread), then you might want to dump it first for backup (see this thread).
Apart from that are warranty issues. The place where you bought your Touch2 might or might not be willing to do warranty repairs if you messed with your phone's ROM. Of course, you can always flash back the original ROM (or your backup), and also flash back the original SPL. In this case it would be hard to get no warranty, if you didn't destroy anything else by yourself.
6. Before you can flash a new ROM: HSPL / HardSPL
Normally you can only flash original ("Stock") ROMs that are meant for your device. If you have a standard Touch2, then these are the ROMs directly from HTC. These phones, which have no brand name by some telecom company (like T-Mobile, Orange, ...), are called "unbranded" phones. If you have a branded phone, then you can only flash the ROMs provided by your telecom company. If you try to flash anything else, it will either show an error message, or you even might risk bricking (destroying) your device. Think of the SPL as the piece of software that starts first when you turn on the Touch2. There is a security lock in there, which prevents custom ROMs or other language ROMs to be flashed. There is, however, a modified SPL made by the XDA-developers user jockyw2001. It is called HardSPL or HSPL, and allows you to flash basically whatever you want. (Note: There might be some restrictions still, I am not sure - someone might want to give more info in case certain ROMs like Russian need more than just HSPL)
To change your SPL to HardSPL, please go to the first post of this thread and follow the directions there very carefully. There are lots of small hints what you can do to make it work, even if it doesn't work at first.
7. Checking your SPL version: SPL Tri-Color boot screen
Turn on (or reset) while you keep the "volume down" key pressed. You will see a screen like this:
If you have changed your SPL to HardSPL successfully, this screen will say SPL-1.28.Hard
8. Where to get ROMs
To get stock (HTC standard) ROMs in other languages, visit the Mega - ROM - Hotfix - User Manual - roll-up thread
Or check http://shipped-roms.com/shipped/Mega/ or http://htcpedia.com/soft/mega-touch2-rom.html
For user-built custom ROMs, check out the many threads in this part of XDA Developers
Finally, you might want to create ("cook") your own ROMs. You will have to learn a lot... osKitchen supports MEGA, and Chef Central has lots of resources. Good luck!
Here some newbie info on starting to build ROMs from fktsndr:
fktsndr said:
-[WM Kitchen] osKitchen NEW UI v1.25 - Easy Visual Kitchen
-[OS][WM6.5.5] Latest Releases (23563), Porting, Tutorials, Tools, VM, etc.
-[REF] Updated 27-Apr: Latest 6.5 and 6.5.x builds and Manila builds for Rom selection
Useful softwares:
- OSKitchen MEGA (with working htcrt_devices.ini and ferom file)
- WinCE Cab Manager (not free)
- OEMizer
- MSCEinf
- HardSPL kit for Mega Touch2 by jockyw2001
- QuickCAB
Click to expand...
Click to collapse
9. How to flash a ROM
Please go to the first post of this thread, there is a custom ROM flash utility attached at the bottom of the first post. You can also download it with this direct link. If that one doesn't work for you, DrJason pointed out that the utility in this post works OK as well, also under Vista.
You basically need to do these steps:
(Connect the phone to your Windows PC with the USB cable, you need to have Active Sync set up and connected to your phone)
1. Apply HardSPL (Number 6 above) and check that it was successful (Number 7 above)
2. Restart the phone and boot normally
3. Copy the ROM file (nbh file) into the same directory as the ROM update utility
4. Run romupdateutility.exe and follow the instructions on the screen
5. After flashing is complete, do a hard reset (Number 10 below)
Note: Alternatively some people had success flashing from an SD card, where you don't need an PC connection. The card must be FAT32 formatted and less than 4GB total capacity. Rename the ROM (".nbh" file) to "PB74IMG.nbh", copy to your card, switch off phone, hold volume down and press power button, then continue according to the instructions on the display.
10. How to fix many issues: Hard Reset / Recovery
To reset your Touch2 completely you can do a hard reset. This sets everything back to the currently flashed ROM's defaults, so you should do it after every new ROM you flash. Caution! That means all of your settings, programs, SMS, phonebook (unless on your SIM), messages, modifications, etc., will get lost! So do a backup first. (See number 11 below)
Turn on (or reset) while you keep the both volume buttons pressed. A screen will appear asking you to press "volume up" to do the hard reset, or any other key to cancel it.
11. How to backup some stuff
For Appointments, Call Logs, Contacts, SMS & Messages (no MMS!), Speed Dials, Tasks etc. you can use "PIM Backup" which you can find in this thread.
Another way to backup for example contacts is to synchronize with a program on your PC like Outlook.
<reserved>
<reserved>
Good work buddy, this must be sticky.
Great overview, simply and all in one.
Good work, thx
Great work! thank's for the tutorial it answered me lots of questions I had!
as always your the noobs best frnd
learned something new today. downloaded wwe Asia ship(2) 1.32.729.3(72483), one that the model number of your phone is known by the firmware. my t3333 changed into t3320 :/. for guys looking for stock English roms, this is no go.
Gothik said:
learned something new today. downloaded wwe Asia ship(2) 1.32.729.3(72483), one that the model number of your phone is known by the firmware. my t3333 changed into t3320 :/. for guys looking for stock English roms, this is no go.
Click to expand...
Click to collapse
I am using this WWE asia ROM, and my system says T3333: http://rapidshare.com/files/3001039...Radio_Signed_61.41t.25.31_3.48.25.27_Ship.exe
yellowfever said:
I am using this WWE asia ROM, and my system says T3333: http://rapidshare.com/files/3001039...Radio_Signed_61.41t.25.31_3.48.25.27_Ship.exe
Click to expand...
Click to collapse
read properly...
Gothik said:
read properly...
Click to expand...
Click to collapse
I was just trying to suggest a different WWE ASIA rom for you, which does not have the issue you mentioned. Sorry if this answer did not meet your expectations.
Question
Hi!
Thank you for this thread.
I have a question. You wrote that you need the HSPL cause a branded Phone blocks custom roms. How about an unbranded phone?
Weatherlights said:
Hi!
Thank you for this thread.
I have a question. You wrote that you need the HSPL cause a branded Phone blocks custom roms. How about an unbranded phone?
Click to expand...
Click to collapse
Not just branded phones, you can not install wwe rom to italian device,you can not install WWE rom to asian wwe device, etc.
If there is an error during flash (hard drive fail, blackout), your device wont be a brick, you can step to bootloader and flash again.
So the best way to install hard-spl, and you can do anything
Upgrade or instal a new ROM
Hi yellowfeaver,
I find your review very good and clear.
But I have just one question:
Is there a possibilities to upgrade or install a new ROM in my Mega under the Windows 7 ultimate x 64?
Everything I'll try, evan the hard SPL, it give me an error.
Is an incompatibilities with this OS, is necessary to install a x86 version of Windows 7, or this kind of problem is for all x64 Windows OS?
Thanks in advance and for your advice,
Best regards,
ok guys any one answering it?
imo if active sync or w.e comes pre installed with win7 workd and detects your mega, then everything should go fine. but of course i don't even recommend win7 for his. goto someone with win xp and get it done.
Win 7x64
Hi Gothic,
As I say the x64 of Windows Mobile Device Center 6.1( for Windows 7 x64) does not recognized my Mega for HSPL and ROM's. Is working well for files transfer, internet share etc
Before I've installed the x64 version on my PC, with HTC Artemis I was able to do everything - HSPL, the new ROM's, file transfer etc - but I never used for Mega because at that time it wasn't an HSPL for Mega. Meanwhile I installed the x64 Windows 7 OS and I couldn't use this OS for Artemis and I realized that for Mega also.
Because are two versions of Windows Mobile Device Center 6.1 ( x86 and x64 ) and in Windows 7 x64 is already created the x86 directory for this kind of applications I will give a try to the version x86. Why not?
I'll be back with a result.
Thanks anyway for your answer,
Best regards
Win7 x64
Definitively refuse to work.
Maybe a new HSPL for this OS will be solve this problem.
I flash every my rom on Win 7 x64, so it goes....
gabrielmihai said:
Is there a possibilities to upgrade or install a new ROM in my Mega under the Windows 7 ultimate x 64?
Click to expand...
Click to collapse
czdjj said:
I flash every my rom on Win 7 x64, so it goes....
Click to expand...
Click to collapse
then why don't you solve his problem?
HardSPL finally done
Hi,
Thanks for your help.
The solution it was to change one registry in to the WM. Thanks to jockyw2001 for his HSPL and all developers who search for the solutions.
"still doesn't work look up this registry key in the phone:
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\EXT_FLASHDRV]
Change the value "Dll" from "OEM_FLASHDRV.dll" to "OEM_FLASHDRVXXX.dll" and reboot the device. After rebooting into WM and after activesync is ready run flash-hardspl.bat . Check in tricolour bootloader screen if it is installed and then boot again into WM and change the registry value back to its old value."
Best Regards,

Categories

Resources