I have an new titan, and it has spl-1.20.olipro bootloader.. I am trying to reflash but it reboots at 11%. I can't get any roms to fully flash.. It's stuck on the HTC black screen and say's not radio..
I need help.. how can i fix this cux i can't get any roms to flash... cooked or official
use the boot loader in the guide bellow
follow this guide and start all over
it was stuck in 1.2 olpro. I cant get any rom to flash or update to 2.40... I tried to flash radio 3.27.. that went 100% but now the phone won't even turn on
do you get a charge light when you plug it in to the wall? if so make sure its not dead, ya never know.. lol
no i don't get anything.. no charge light or anything.. it dead
yeah sounds like a brickk... sorry =\
take it in and try to get another one
jmann76 said:
it was stuck in 1.2 olpro. I cant get any rom to flash or update to 2.40... I tried to flash radio 3.27.. that went 100% but now the phone won't even turn on
Click to expand...
Click to collapse
***EDIT***
Dang, I just read your post about your light not even turning on. Did you try soft resetting it? I know that sounds dumb, but had to ask. Did you try taking the battery out for a bit? Try holding the Power button and the Camera button down on the right side of the phone and push your stylus into the soft reset hole. That's the way to put it into bootloader mode. If you've got the phone plugged in even (try it without the battery too) and you still don't get anything, then I'd say try to get it replaced if you can. That's never a good feeling. I've had a couple of HTC devices now, and have been there a couple of times where you think your phone is dead, but it ends up not being that way. I hope this situation goes the same way for you.
*********************************
3.27 requires 2.40 and is also outdated.
You could try the Titan Relocker to put an older bootloader version on it, and then flash an official rom that supports GPS, which will update you to the Carrier's ROM and Radio. At that point, you can try to unlock and flash to 2.40.
Once you have 2.40 installed, you can then put on a 3.xx radio (3.39.10 is recommended right now) and flash to a custom ROM, such as DCD's newly released 3.1.6 ROM. I think it runs really well, and I flash mine to different roms way more than I'd like to admit. I think I'm going to stay with this one for a while.
Once you get the 2.40 bootloader, I'd start using the SD Card flashing method for your ROMs exclusively. It works really well, and the good thing is that you can have other stuff on the card, so you can use a small card by itself only for flashing, with folders for different ROMs and Radios, or you could use one big one, and then just change the required file every time you wanted to flash.
I haven't included links to everything because that would take a while, but you should be able to find everything I've mentioned by using the search function, or if you can't seem to find what you're looking for here, you can try ppcgeeks.com too, it's another great resource for our phones.
Good luck!
-kmart
P.S. Don't worry too much about your phone, these titans are actually quite hard to brick. As long as you can get to the bootloader, you should have a good chance to get everything working properly again.
jmann76 said:
I have an new titan, and it has spl-1.20.olipro bootloader.. I am trying to reflash but it reboots at 11%. I can't get any roms to fully flash.. It's stuck on the HTC black screen and say's not radio..
I need help.. how can i fix this cux i can't get any roms to flash... cooked or official
Click to expand...
Click to collapse
You are fine. Though as your Titan is already unlocked and had an older third-party ROM installed, it ain't so "new" . Your problem is covered in the Wiki:
II. Install the correct bootloader
Hit Power-Camera-Reset to check what version of bootloader you have installed.
At the tri-colour bootscreen you will see the version number installed.
if it is 1.04 or 1.06 then you must unlock your phone and upgrade to 2.40. Olipro 1.20 is not necessary at all when using newer ROMs/Radios.
if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40.
if it is 2.40 then you have the correct bootloader and are ready to move on to the Radio Upgrade in Section III.
michaelm91 said:
use the boot loader in the guide bellow
Click to expand...
Click to collapse
Guys, the info first presented in that thread is out of date and not maintained. Please let it disappear and first direct people in help to the Wiki.
jmann76 said:
...that went 100% but now the phone won't even turn on
Click to expand...
Click to collapse
Oops, I just read that too... Remove the battery or try another battery yet? Other than that...
how did things finally turn out jmann?
Related
Hi,
I thought I did enough reading to hard-spl my g4 cingular 8125 but i guess not...
Anyways, I did the hard-spl and everything seemed to go smoothly. Then I went ahead and tried to flash the Touch no Evil ROM (http://forum.xda-developers.com/showthread.php?t=327215).
About 4% into the flash I got error 262: update error. Now the device is stuck on bootloader with IPL 2.21.0001 and SPL 2.21.01ip. Plugging in the usb shows "USB" at the bottom left corner of the wizard's screen but I cant detect the device in windows. Since I cant detect the device, I cant remove hard-spl and attempt to reflash using soft-spl the stock 8125 spl and rom.
Anyone have any suggestions on how to remedy the situation? Or did I just brick this thing
Any help or even linking to the right threads would be appreciated. A couple hours of searching didnt yield anything but maybe im looking for the wrong things...
Thanks,
Anushian
EDIT: More searching yielded this: http://forum.xda-developers.com/showthread.php?t=276963&highlight=stuck+bootloader
Basically use MTTY_updateROM.exe to dump the ROM onto an SD Card and restore from that? I dont have a card on me so Id rather get some input before going to buy one just to try this... Mainly, I need to know if the hard-spl still renders the unit CID unlocked and capable of preforming this method.
hello
i had the same problem and it seems its the Ruu i guess you used the ruu thats in touch no evil rom but your device is ok use the wizard love rom http://forum.xda-developers.com/showthread.php?t=298613 and then flash again with the tool that said in g4.7 and it works dont flash to original rom because it contains isp spl and can brick your phone i hope it helps.
Solidus_k said:
hello
i had the same problem and it seems its the Ruu i guess you used the ruu thats in touch no evil rom but your device is ok use the wizard love rom http://forum.xda-developers.com/showthread.php?t=298613 and then flash again with the tool that said in g4.7 and it works dont flash to original rom because it contains isp spl and can brick your phone i hope it helps.
Click to expand...
Click to collapse
Hi and thanks for the tip. I tried wiz love rom flash again and this time it worked (didnt recognize usb first time?). Anyways it went up to 6% and died since the battery died. Im going to just get a standalone charger and charge it and try again. Will probably take 2 weeks to get here though...
My main question is, based on the info provided, is the phone bricked or is it still repairable with a reflash? I didnt find much info related to hard-spl and restoring with the SD methods besides just that the phone must be CID unlocked...
Thanks!
if you have hard spl then you have cid unlock so your phone is ok if you flash wizard love rom use the ruu thats is in wizard love folder dont flash any official rom, try to change from computer or stop running other programs while flashing and your device is not bricked unless you intall official rom.
Solidus_k said:
if you have hard spl then you have cid unlock so your phone is ok if you flash wizard love rom use the ruu thats is in wizard love folder dont flash any official rom, try to change from computer or stop running other programs while flashing and your device is not bricked unless you intall official rom.
Click to expand...
Click to collapse
Hi Solidus_k,
Thanks so much for the info, much appreciated. I'll give it a go again as soon as my charger arrives in the mail since my batteries dead. Just wish you didnt have to boot into winmo to charge...
Anushian
FIXED! Read below for details.
So i've been messing with my mogul for nearly 4 hours now trying to convert it to dcd's rom..and i've flashed it twice now and after it reboots from being 100% loaded it just sticks on the HTC black screen..I've read and read and searched and searched and cannot find a definite answer. Can anyone help?!
basics?
did you load the radio rom?
did you load the unlocker?
you may need to restart the phone to the boot loader and resend the rom
(press and hold camera and power and push reset button)
I did TRY and reload the radio and unlocker..now im stuck at the black htc screen where it says no radio though. bleh. i can't even get it back up and running. what do i do?
edit:
I'm at the multi color screen..ive tried running the unlocker RUU and then running dcd's ruu and it doesn't work..and the radio RUU does not run at this screen...I can't get the phone back to a working status! Argghhhh. It wont let me run the relocker unless im in activesync...but i can't be recognized in activesync unless the phone is up and functional..so..? how do i relock it to put hte stock rom on to try and unlock again?
I am kinda stuck in the same spot, but mine is is the verizon logo screen, i tryed doing the power,camera and hte reset button but its till stuck, i tryed the relocker but i need to be in active sync
any help?
what i dont get is..i flashed it with the unlocker, then the rom then the radio...isn't RUU just overwriting each one or something? it doesn't make sense to me. and all i can do is run RUU..i did the rom, then the radio and it was stuck in the bootloader so i used the exitbl and got out of it but then it just went back to going to the HTC black screen saying no radio. ..i'm gonna try and flash the rom from a sd card next..we'll see what happens..
jkrolcz said:
I am kinda stuck in the same spot, but mine is is the verizon logo screen, i tryed doing the power,camera and hte reset button but its till stuck, i tryed the relocker but i need to be in active sync
any help?
Click to expand...
Click to collapse
This just happened to me after flashing the ROM but not the RADIO yet. Flashing the Radio fixed the problem.
I've flashed the radio..then its stuck in the BL and i use the program to get me outta it then it just keeps saying i have no radio! what the hell..this sucks. i'm in the worst possible situation to have to buy a new phone
There are three parts to the "operating system" of your phone.
1. Bootloader (also called locker, unlocker, re-locker, SPL)
2. Radio
3. ROM
The three components are saved in discrete portions of the device's memory. Flashing one does not overwrite the others. All three must be compatible for the phone to operate properly. If you stop the upgrade process recommended by the ROM compiler prior to completion, your phone may not operate properly. If you flash the "leaked" 3.16 ROM package, it contains all three components.
To use the 3.16 stock OEM ROM, or a custom ROM based on the stock OEM 3.16 ROM, you must have a level 3.xx radio and a level 2.xx bootloader. The current implementations of those are the 3.27 radio and either the stock bootloader distributed with the "leaked" 3.16 ROM package, or the Olipro 2.40 unlocker.
If you are running a level 2.xx stock OEM ROM, or a custom ROM based on a stock 2.xx OEM ROM, you must have a level 1.xx bootloader and a level 1.xx radio.
Custom ROMs are not always named using the OEM convention, so you must research the custom ROM to determine whether it is based on a level 2.xx or 3.xx stock OEM ROM.
I hope this helps all of you get your phones back up and running.
FIXXXED!
So heres the best description I can give of what was going wrong for me..Its my first time trying flash to a different rom..and well it didn't go so well. First, I used the titan unlocker, then installed the radio (not sure which one) and then some form of the newer dcd rom and i was getting stuck on the black HTC smart mobility splash screen where it said "no radio". I had to have messed around for over 5 hours today at college trying to figure it out by doing different arrangements what order i installed the radio and unlocker and rom in. I couldn't get it to connect with activesync so i couldn't use the titanunlocker.exe..all i was going off of was RUU's. Im not sure whether or not what OS I was using effected it..I was playing in Vista earlier today but had done the correct steps to install the drivers, and now this last time i did it on XP. This last time I ran the 3.27 radio RUU as found.. here ( http://forum.xda-developers.com/showthread.php?t=362563 )...Theeen I ran this form of the newer sprint ROM. (I'm pretty sure they say it comes with a included in this RUU, but i'm just stating exactly what I did) the .651 rom can be found.. HERE ( http://forum.ppcgeeks.com/showthread.php?t=16806 ) He had a error when packing or something so you have to manually rename it to .exe because it was missing a e..I did this within winrar before extracting..ran that and about 10 minutes later it booted up and i've got service. I'm not going to promise that this is 100% functional all i'm saying is im out of that horrid black HTC screen where I can now go on to try and get the correct rom i wanted. Hope this helps..may be a bit confusing and probably did things wrong but this was my first time doing it all.
Hello everyone i Just got a xv6800 and am trying to flash to a newer rom...However i cant seem to boot into the bootloader it just hangs at Loading.... There is nothing installed its factory rom and settings
Thx in advance
How are you attempting to load into bootloader?
The way I saw on the forums....holding power and camera button and hittig the reset..i get the tri color screen then it goes to Loading... and just sits there dosnt do anything else
Do you have a microsd card in while trying this? If so, does it contain any .nbh files on it in the root directory? If so, do you have a TITAIMG.nbh file in the root directory?
The only way the bootloader would try loading something the way you're describing is if this is the case.
I agree with gcincotta.
If you are in fact trying to flash from the SD card though, most people have reported that it won't work using an SDHC card. It needs to be a standard (non high-capacity) card.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Well i got it to go to usb but now the .exe file for the 2.40 unlocker wont run on x64 systems so i guess im out of luck huh
Did you already run the unlocker? If so, you should be ready to flash a custom ROM. It is normal to be stuck in the bootloader after an unlock. Just flash away.
If the unlock did not go successfully, you will have to try again, making sure to follow directions precisely (on a 32bit system preferably, less headaches). To unlock you must be booted up into Windows Mobile. You can try the exit bootloader program from the PPCGeeks Titan Upgrade forum, or try flashing a stock ROM to get back into WM.
Edit: You can tell if the unlock was successful by looking at the SPL in the bootloader (right under TITA100 MFG). It should now say SPL-2.40.Olipro. If it does not, try the steps above to get back into Windows Mobile.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Click to expand...
Click to collapse
You need to be more specific. Everyone's titan says TITA100. What SPL is installed? Post the entire contents of your screen and then we can get somewhere.
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
I was able to udate to 2.52 rom...the 3.04 wasnt working correctly and it would not up date using *228..and there was no sound...i was not using the radio 3.35 because i heard people saying that it was a bad one to use...is there much difference in performace between 2.52 and the 3.04?
So I need to install Sprints 3.35.651.2 rom and not let the sprint customazations run.
Then use the unlocker 2.4
Then use DCD or No2Chem custom rom.
craig540 said:
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
Click to expand...
Click to collapse
You are starting from scratch with an unlocked phone. Before rushing forwards you have some reading to do:
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
All of your answers are there.
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
craig540 said:
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
Click to expand...
Click to collapse
1st- update to 2.4 olipro
2nd- update sprint 3.35 rom (stop at the "tap the screen" customization screen) this gives you the radio
3rd- from customization screen start the 3.0.4 rom and flash that rom
Your phone will restart after loading and will boot into wm6.1
4th- Read untill you understand before flashing roms
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
craig540 said:
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
Click to expand...
Click to collapse
Does not matter, if you do it in rom it will force into bootloader anyway.
Ok up and running dcd 3.04
date 2-22-08
radio 3.35.04
I did not let sprint cutomazation run.
Tried to make a call and get message saying verizon can not authenticate and to dial #8899
Should I do that now?
Had to call VZW to get new A-Key
No GPS detected in google maps is there anything I need to do to set it up ?
Try installing VisualGPSce -- it's a good little & free diagnostics program too see GPS satellite reception.
....after seeing that running on COM4 at 4800 baud, then you should see a list of visible satellites. Now, whether or not you get a sufficient lock within the first half hour depend's upon your luck in the draw for a GPS functioning Titan -- GPS hardware-wise, not all are equal.
Hi there, I have very minimal experience with this stuff so I will provide as much detail as possible...
I had previously successfully programmed my HTC6800 back in March by unlocking with Olipro 2.4, then I flashed the radio with 3.27 and used dcd 2.3.2 for Bell on it. Now my memory is a little foggy as that was several months ago however I made it through the process fine. This encouraged my to try to update again today. I tried following the steps in the wiki as I could not find the guide I had used previously. I already had Olipro 2.4 so I was good at that step. I then tried running the newest radio update and it would not take. It gave me an error. I reset the phone and tried several times but to no avail. I then tried putting on dcd3.2.0 which went fine. THe phone rebooted and I made a test call and everything was fine. I however wanted the new radio update still so I thought I'd take another crack at it... it still would not update. In the wiki it said about relocking the phone and putting it back to the factory ROM and starting again. So I did this, I downloaded the relocking util and followed the instructions to relock the phone. That went fine... Olipro is gone and is shows the 1.06 like it's supposed too... next it said to put the factory ROM back on... well, I am will Bell and the link for the factory ROM is dead! I can't get it anywhere!!!
So currently my 6800 sits as the 3 colour screen with 1.06 relock on it and does nothing else. It has radio 3.27 on it and dcd 3.2.0.
Is there any way to fix this?????
Run this first to exit the bootloader and get into windows mobile. Then check out which rom you are on (I think you were on dcds rom). Then load radio via sd card method listed in the wiki. Then reload dcd if you are not already on the version that you want.
P.S. I have heard things about that ROM that it caused problems. You may want to read up on that here.
Nope
Well, I downloaded the file and tried running it but to no avail. It just comes up saying that the application failed to start because RAPI.DLL is missing.
Also
I tried running that app on a Vista machine as well and it just says that it can't open the USB port. However, windows found the device and installed a driver for it when plugged in AND it shows USB on the bootloader screen when plugged in.
ok..,. let me see...
try installing olipro 2.40 again, it seemes that your phone is locked (olipro 1.06) so it can't run the dcd custom rom... reset and see if you can enter windows...
then if you enter windows normally, downgrade to olipro 1.20 and install the new radio, then, once again upgrade to olipro 2.40 so it can enter windows...
let me know if it worked for you...
Evo69 said:
well, I am will Bell and the link for the factory ROM is dead! I can't get it anywhere!!!
Click to expand...
Click to collapse
Install another carrier's stock ROM (though to keep things easier avoid the Telus one as it doesn not include a radio ROM) and avoid letting it run any customisations after boot/screen calibration.
You are fine.
Here's the problem
OK. Here's the problem. I obviously misread the instructions on setting the unit back to stock as I just read them again and I realize my mistake. I did not load the stock ROM on first. I used the Re-lock program and re-locked my unit before putting the stock ROM back on. So I sitting at the 3 colour screen with SPL 1.06 and I have radio 3.27 on the unit and dcd's latest ROM on it. I can't get it past the 1.06 bootloader. I have tried a hard reset, I have tried the program above to exit the boot loader and it does not work. Is there any way I can get Olipro 2.4 back on or exit this bootloader???
just connect your phone to the computer (it's ok to be on the tri color screen) and install olipro 2.40 from the computer...
you just need to be sure that when you connect the phone in the tri color screen it says USB...
i'm attaching Olipro 2.40
No Dice
Nope. I had tried that already. I just tried again. When I run Olipro 2.40 the command prompt comes up and then come up with a window saying "Cannot Find Device" (or something VERY close to that). It then asks if you'd like to retry, clicking retry just keeps bringing up the same message. If you click "No" on retrying it will eventually move on to the next step and load up the flash program. It will then attempt to flash the unit (Grey screen with the status bar comes up) but it just sits at 0% and eventually comes up with a 242 communication error.
i had a similar problem yesterday when i tried to upgrade the radio form 3.42.02 to 3.42.30 and taht solved my problem...
so you basically cannot exit the bootloader mode?? even when you hard reset your device??
Can the unlocker be flashed from a memory card? Has anybody ever tried?
Evo69 said:
Nope. I had tried that already. I just tried again. When I run Olipro 2.40 the command prompt comes up and then come up with a window saying "Cannot Find Device" (or something VERY close to that). It then asks if you'd like to retry, clicking retry just keeps bringing up the same message. If you click "No" on retrying it will eventually move on to the next step and load up the flash program. It will then attempt to flash the unit (Grey screen with the status bar comes up) but it just sits at 0% and eventually comes up with a 242 communication error.
Click to expand...
Click to collapse
I have the Bell ROM if you're looking for it.
TS
I didn’t think it was possible to flash back to a stock Bell (non-GPS) rom/radio after flashing to a GPS radio.
Does anyone know if it’s possible to flash the SPL (bootloader) from an SD card?
No2chem over at ppc geeks has a new SPL that loads from the device, but it needs be running.
http://forum.ppcgeeks.com/showthread.php?t=30561
jhamilton said:
I didn’t think it was possible to flash back to a stock Bell (non-GPS) rom/radio after flashing to a GPS radio.
Does anyone know if it’s possible to flash the SPL (bootloader) from an SD card?
No2chem over at ppc geeks has a new SPL that loads from the device, but it needs be running.
http://forum.ppcgeeks.com/showthread.php?t=30561
Click to expand...
Click to collapse
I haven't tried to do it yet, but I did develop a theoretical how to before I first flashed my phone as I wanted to make sure I had a way out. You can find it here:
http://forum.xda-developers.com/showthread.php?p=2017265&highlight=bell#post2017265
YES
Timeshell said:
I have the Bell ROM if you're looking for it.
TS
Click to expand...
Click to collapse
Ya, if you can post attach that file to a posting on here I would appreciate it. If you need an alternative method of send the file to me just PM me and I will figure something out.
Keystone said:
Install another carrier's stock ROM (though to keep things easier avoid the Telus one as it doesn not include a radio ROM) and avoid letting it run any customisations after boot/screen calibration.
You are fine.
Click to expand...
Click to collapse
I tried using a Sprint one... it would not work.
Timeshell said:
I haven't tried to do it yet, but I did develop a theoretical how to before I first flashed my phone as I wanted to make sure I had a way out. You can find it here:
http://forum.xda-developers.com/showthread.php?p=2017265&highlight=bell#post2017265
Click to expand...
Click to collapse
Yeah I've heard some horror stories when it came to downgrading, including a few bricked devices.
http://forum.ppcgeeks.com/showthread.php?t=26082
I would be interested to know if anyone on Bell has managed to successfully downgrade a 6800 to stock.
i thought dcd's new 3.2.0 needed a radio of 3.35 or higher to run and does not flash the radio when u flash his rom. Another problem with the phone not coming out of the bootloader is that you have to disable usb connections in active sync or windows mobile device center for the exit bootloader app to work. Try disabling the usb connection in whichever one applies for you and run the app again. If you can get out of the bootloader try to go back to ollipro 2.40 or use one of no2chems bootloaders as they work from the device and an sd card no need for a pc to flash the bootloader. once bootloader is unlocked again run a full radio/rom update like the sprint stock 3.35 easily found on htc's website under the titan (us version of the site). Don't let the carrier custimizations run ... the file that runs after u calibrate screen and set timezone just pull the battery. Then grab whatever rom / radio you want to or were trying to flash 2 before and name it put it on the root of an sd card (thats under 2gb and formatted to fat32) and rename the ruu_sighned.nbh file to TITAIMG.nbh hold power + camera and hit your soft reset button. The tri color screen will come up and should say loading then promt to hit the power button to flash and show u what u r flashing. cdma (radio). os (radio rom) or splash screen, or whatever you r trying to flash hit power button to start once done it will sit with update complete on the screen pull the battery out for about 30 sec and put it back in reboot and enjoy the custom rom or radio.
kdj67f said:
Can the unlocker be flashed from a memory card? Has anybody ever tried?
Click to expand...
Click to collapse
You can use nueSPL 2.47 to load the locker/relocker but you need to be booted into WM6 to do so. You need to reload another rom that uses the bootloader you have currently loaded and then you can move forward or backward.
Evo69 said:
Ya, if you can post attach that file to a posting on here I would appreciate it. If you need an alternative method of send the file to me just PM me and I will figure something out.
Click to expand...
Click to collapse
Uploaded to Rapidshare
http://rapidshare.com/files/1271390...3.666.1_RS_1.37.30_BM_1.27_0604_SHIP.zip.html
TS
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
I went from stock to 3.2.0 / Radio 3.42.02.. no problems.
I have not loaded 2.42.30 (I prefer to use the radio version released by HTC for this device.. 3.42.30 was released for another device and ported.. although it seems to work for everyone.)
I HAVE read that for radio 3.42.30 you need SPL 1.20 for USB Flashing.
gc14 said:
Yeah 1.20 is needed to flash these radios via USB. Just need to put 2.40 back when you're done.
Click to expand...
Click to collapse
Based on that.. I assume SD flashing is ok with 2.40.
scotcha12345 said:
... (maybe thinking the Radio needed to be installed for it to get through)....
Click to expand...
Click to collapse
Yes! This is well documented.. a common issue.
If you flash the Rom without a compatible radio.. you will get stuck on the verizon screen... I suggest flashing the ROM AFTER the radio.. since you flashed the Rom already... when you get the radio working, Reflash the ROM.
Did you flash the radio via SD Card or USB?
Did it show a progress bar while flashing?
Let us know how your attempting to flash the Radio (USB or SD) With specific steps (held buttons X, Y, and Z.. saw this message, pressed this key.. saw this on the screen) .. and someone will let you know what you might be doing wrong.
Also.. dont forget to run the carrier cab when your done.. This is worth mentioning since it's the most common issue once the device boots and you cant program the phone, or make data / voice connections.
scotcha12345 said:
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
Click to expand...
Click to collapse
Can you get to the bootloader by holding down camera power and pushing the reset button? If so, you can flash the radio with the SD method found in the wiki. just put the radio on the sd card in the proper format and enter bootloader and it should correct your problem.
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Responses
Hey guys,
Thanks for the responses and suggestions.
1) At the moment he doesn't have an SD card aside from the SDHC, so he couldn't do that until he purchases one. Good idea though if nothing else works
2) When pressing the camera/power/reset he's in the SPL 2.4 bootloader screen, he's going to try your suggestion of downloading Sprints and upgrading.
3) I'll ask him procedurally what else he has tried, what error he gets for recording. No doubt you were correct about uploading the Radio before the ROM
I've actually flashed my phone exactly the same way he has so that I can try to experience the same problems, and try to figure it out myself.
Bingo
Hey,
The Sprint ROM .exe was the answer. Very smart, thanks again for helping us both out. Was getting a little nervous for about 2 minutes.
useful=helper++
I did the same thing. Thank you very much...saved my butt!
BC
its alive
spreeway said:
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Click to expand...
Click to collapse
you saved my titan...thanks guy!