Related
I have a mogul and have been trying to update the ROM all day with no luck, and could really use some help
I have SPL-2-2.40.Olipro bootloader working ok.
I tried to flash the radio rom 3.27.00 first, but it got about half way and errored. It then had me do the battery removal, reboot procedure and restore which said it completed ok. I then tried the rom again, but now it only goes to 9% and then the mogul resets and i get error [328] invalid command.
I then was able to update the dcd 2.2 rom which completed ok, but now I get the yellow splash screen w/ sprint logo and the no radio message. I've tried loading the radio rom again numerous times from the bootloader, but it does the same thing resetting at 9% error 328
I've rebooted the PC, played with the cable connection which seems to be working as the bootloader will switch between serial and usb.
I also tried restoring to the 2.17 rom which I downloaded from the HTC site, but it only goes 1% and errors out with the same [328] Invalid Command
What can I do to get this working?
So are u sure you have the new unlocker
then flash the rom
and then radio
I think so the file is called "Hard-SPL-MFG" and I get the red, green, blue screen that reads:
TITA100 MFG
SPL-2.40.Olipro
CPLD-9
I was able to get the dcd rom to go with no problems, but the radio rom will not go. Like I said it gets to 9% at which point the phone resets and I recieve the error 328 invalid command on the pc.
I saw some others here having the same problem, but wasn't able to find a clear resolution posted
thanks
I also just tried flashing the radio rom via sd card with no luck. I extracted and renamed the nbh file and copied it to the root of a freshly formatted (in FAT) sd card. Whne i start the boot loader I get the white screen and it says loading..... but then just returns to the red,green.blue screen. When i reboot I'm still getting the splash screen with no radio at the bottom
Put your phone in 2.40 bootloader (tri-color screen) and follow these instructions starting from step 4:
http://forum.ppcgeeks.com/showthread.php?t=17667
If that does not work, try it again from step 3.
mogul67 said:
I think so the file is called "Hard-SPL-MFG" and I get the red, green, blue screen that reads:
TITA100 MFG
SPL-2.40.Olipro
CPLD-9
I was able to get the dcd rom to go with no problems, but the radio rom will not go. Like I said it gets to 9% at which point the phone resets and I recieve the error 328 invalid command on the pc.
I saw some others here having the same problem, but wasn't able to find a clear resolution posted
thanks
Click to expand...
Click to collapse
hard set your phone(2 soft keys and soft set botton)
and then load it into bootloader(power botton+camera botton) and then try to load the radio like that
bakntyme said:
Put your phone in 2.40 bootloader (tri-color screen) and follow these instructions starting from step 4:
http://forum.ppcgeeks.com/showthread.php?t=17667
If that does not work, try it again from step 3.
Click to expand...
Click to collapse
I've tried that but I can't get the relocker to run? It says no device connected would you like to try copying again? and I'm on the SPL boot screen its connected etc
I've also done the hard reset, gone back into the bootloader and tried the radio rom again, but it stops @ 9% with error 328 and resets the phone
mogul67 said:
I've tried that but I can't get the relocker to run? It says no device connected would you like to try copying again? and I'm on the SPL boot screen its connected etc
I've also done the hard reset, gone back into the bootloader and tried the radio rom again, but it stops @ 9% with error 328 and resets the phone
Click to expand...
Click to collapse
OK, did you try starting from step 4? That means just flashing the Sprint "leaked" ROM.
if I have Alltel should I still use the same method even though it says it's a Sprint rom?
I have the same issue right now
Thank you I was able to get the 3.16 ROM loaded.
next I ran the Hard SPL unlocker and got the bootloader screen, tried the radio rom install and its still quitting @ 9% resetting the phone?
I need to get the radio to work before installing dcd's rom right?
Ok don't worry, I had the exact same problem as you mogul67 and I was puling my hair out for a day and a half.
If you read kmartburrito's original PPCGeeks page:
http://forum.ppcgeeks.com/showthread.php?t=16806
The edit by ImCoKeMaN says:
I have found that if you have issues where your device seems to be bricked and stuck in bootloader before completion of the update you can fix it by flashing via SD card.
To do this there are 3 steps:
First take the .exe file and open it with winrar. There will be a file 3.16.....nbh extract that and rename it to TITAIMG.nbh
Next format a microSD card with FAT 32 (required most are fat16 default) and copy the file TITAIMG.nbh to the root of the sd card with a card reader.
Finally place sdcard in device and reset into bootloader mode. The flash will proceed from the SD card and it should work fine. Enjoy!
Click to expand...
Click to collapse
By "take the .exe" he means open the Radio ROM flasher with WinRAR, btw... I had to think about that one for a second just because it seemed so simple
So head over to best buy and get yourself a cheap MicroSD to SD adapter, throw it in your favorite card reader, follow the steps and you'll be up in no time
THank you for your help that did it, but I was able to just run the 3.16 ROM from Windows with no sd card. After loading that ROM I was able to run the unlocker, hard spl, and then update the ROM
thanks again
Hi Folks,
I'm stuck in the tri-color screen for bootloader 1.06.
I have DCD 3.2.0 w/3.42.02 radio on the XV6800 and was trying to upgrade to radio 3.42.30. My system is Vista 32-bit.
I ran the Titan Relocker and it put SPL-1.06.0000 back onto the device and was planning on then putting 1.2 onto it.
Running titan_exitbl.exe says "Cannot open USB port. Please make sure, that USB connection in ActiveSync is disabled."
Unfortunately it is now stuck and even after ending the Sync Center service I can't get titan_exitbl.exe to pull it out of the Boot Loader.
Ideas? Thank you!
I could fire up an old XP laptop and try it from there.
Loaded ActiveSync 4.5 on an XP laptop, disabled USB connections, ran titan-exebl.exe and the device is booting now.
I'll continue on and see what else I can screw up.
Loaded SPL 1.20
Loaded 3.42.30
Loaded SPL 2.40
Device is back to working! Off to see if GPS is back after being lost with 3.42.02.
titan-exebl.exe
Where can I find titan-exebl.exe? Google doesn't turn up any results other than here?
titan_exitbl.exe
Never mind... just located it on my own hard drive!
Cheers!
Stuck on Bootloader
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Try changing your spl back to 2.40.
Throwing it back into the tri color screen again and flash the sprint stock 3.35
But put it on the root of a fat32 formatted micro sd card in the flavor of under 2gb.
Just run the exe from your computer it will extract the files from the exe to some location on your computer, normally the ruu update folder.
There will be a ruu_sighned.nbh file locate it and copy it to the fat32 formatted card rename it TITAIMG.nbh
Let the phone boot into the bootloader and it should detect the file on the sd and update the rom for you, by stating loading ......
Then will prompt you to update press power key.
Sense you are not on sprint don't let the first time custimizations run ... pull battery once you get to your mobile today screen on first boot...
Use active sync or the sd method to update your rom to whatever you wanted originally.
Most full updates from carriers the ones that flash both the radio and rom will run regardless of the boot loader thats on the device.
Happy flashing
Just thought I'd toss in here that GPS does work, but I have to use GPS Viewer to get a lock on the satellites first.
softwind said:
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Click to expand...
Click to collapse
please i have this problem how to fix this?
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
drewcam888 said:
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
Click to expand...
Click to collapse
Thanks!!! Ok, i cant remember eactly what is the v radio but i think 3.35 or 3.42 i cant remember exactly it's one of these. the SPL 1.06 Locked i cant unlocked i cant use titan_exitbl.... the SD update doesnt work stuck on loading.., i cant update from pc stuck 0% then Recovery Error help me. I My phone is bricked? Sorry for my english....
Did you try to install 2.4 unlocker?
drewcam888 said:
Did you try to install 2.4 unlocker?
Click to expand...
Click to collapse
Yes, i try from SD and nothing stuck on loading... from windows with RUU nothing 0% stuck and then UPDATE ERROR[262] now i don't know to do
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
drewcam888 said:
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
Click to expand...
Click to collapse
Ok, but how run from windows? If i cant connect via activesyncs the phone is on SPL mode i cant out of that and the msdos windows say "No device conected" when press enter from windows i cant unlock. Any idea? I'll try 2.47 but how run from windows with the phone en SPL Mode?
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
drewcam888 said:
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
Click to expand...
Click to collapse
Look i cant run Hard-SPL-MFG (Olipro 2.40 Unlocker) because when i run the Bat Or MSDOS Windows say "No device connect" question me if i want retray copy the file.
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
drewcam888 said:
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
Click to expand...
Click to collapse
No luck, method A SD Card Loading.. then cheking... then show a number corner 00028002 and say down Not allowed.
Method B, via PC and RUU then ERROR INVALID VENDOR ID.
Any idea? Thanks bro.
I think my phone is bricked... noway load the rom... i've tried load bootloader unlocked via SD last option and nothing!! damn this is so
Just did the titan unlocker and now the p4000 is stuck in bootloader with these 2 lines:
TITA100
SPL-1.20.Olipro
i think i need some help
thanks in advance
Marc
edit:
RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.0 4_PPST_0619_Ship.exe >>> would flashing this ROM and Radio save me or my titan?
orangeworx said:
edit:
RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.0 4_PPST_0619_Ship.exe >>> would flashing this ROM and Radio save me or my titan?
Click to expand...
Click to collapse
yes..............
since i'm stuck in bootloader mode, how can i use the ruu update utility ?
i'm getting connectiong failed and only option is to exit utility
any ideas ?
if u are in bootloader connect the usb cable and the phone should say usb at the bottom, just open up the ruu update and it should work just fine
Error 264
update utility cannot connect to your pda
and it says USB on the bootloader screen
SPL is 1.20 olipro
take your SD card out if (with phone powered off) if u have an image on the SD card and retry
no SD card being used at the moment
edit: it seems now it is flashing...
let's say this does work, fact that i'm putting a sprint ROM on my telus phone is gonna be alright?
re-edit: crashed at 11% - invalid command error 290... RUU encountered a communication error
recovery
at 11%, titan reset and went back into bootloader mode, RUU crashed but gave option for recovery which was "successful"
retried the same RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.04_PPST_0619_Ship.exe
and crashed again at 11%
i think i killed my phone
i can't seem to do anything, not the telus wm6.0 ruu nor the one stated earlier...
is there a way i can revert to my previous SPL 1.04 ?
really appreciate the help @ 5:35 AM
got my telus wm6 to run and then decided to up to olipro 2.40
now it won't got past second splash...
radio is 1.32, rom is dcd 3.2.5
now from my understanding of what i've been reading is that i need to revert to olipro 1.20 to be able to flash my radio
and i can't do that since i can't get activesync.
any ideas ?
Get a SD card. Go to WIKI and following reverting to Stock. Then start over on flashing. I have done as you did and fixed the phone.
your phone sounds jacked up, how long is it stalling at 11%, r u giving it decent enough time?
redownload the latest sprint rom from htc america here:
http://216.139.227.226/RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_TITAN_3.42.02_SPCS2.04_PPST_0718_Ship.exe
let it run for at least 20 minutes before deciding it crashed...after 1st boot softreset before letting it run any customizations
I tried posting over at PPC Geeks but not sure if someone here might be able to help:
I was trying to install a custom rom to my mogul that i think required Olipro 2.40. Turns out i only had 1.20 & now whenever it boots it just restarts over & over. Since i can't run any relocker or olipro 2.40, all i can do is try reflashing roms or putting items on the SD card. Does anyone have a tutorial on how to upgrade to olipro 2.40 & a rom? I've done it no problem before, but now, like i said, i'm stuck in a boot loop.
Is there an NBH of the relocker than i can put on my SD card & the update to 2.40? I had the two files (they run as batch files which require me to have an avtivesync connection which i cannot get). but neither of them upgraded me to 2.40.
~Thank you so much in advance. I'm just really frustrated after trying so many differnt things. My phone isn't bricked, correct? i can stop this boot loop? I've searched around but couldn't find any solution's to my problem.
Through the official updater, it gets to 11%, the phone resets & never resumes the update. I tried taking the RUU_signed.nbh, renaming it to TITAIMG.nbh, it loads' starts to update, then i get:
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
OS -
The progress bar starts to go up, then at the top i get red text saying "00018003 TITAIMG.nbh - FAIL"
& at the bottom "Update Terminate // UPDATE FAIL"
hello.
all day i tried to upgrade my radio in htc tytn (hermes 200). i tried different radio versions, such as 1.47 ; 1.50 ; 1.51.
at the moment i have radio version 1.03.03.10
somehow i cant upgrade it. all the times radio upgrading ends with 3 color screen.
please help me! it would be very nice, if someone can write step-by-step instruction
p.s. i tried to upgrade radio from this instructions forum.xda-developers.com/wiki/index.php?title=Hermes_ExtractedRadioRoms (upgrade instructions at the bottom in that site) and i tried to upgrade radio just by opening that radio ruuwrapper.exe
please, help!
You should use the SD card method. It's safer and easier. Here's a guide from the wiki:
forum.xda-developers.com/wiki/index.php?title=Hermes_SDCardFlashing
Basically rename the radio rom to HERMIMG.nhb and dump it onto the root of your sd card. Then boot into bootloader mode and follow instructions from there. Also make sure you're phone has a sufficient battery charge and is plugged into a charger.
hmm.. something isnt working anyway.
- i deleted all files from my 2 gb micro sd card.
- i downloaded radio version 1.54.30.10, extracted in new folder on my desktop.
- renamed "RUU_signed.nbh" to "HERMING.nbh"
- copy-pasted it to my empty micro sd memory card
- pushed "ok" and "on/off" buttons and reset button with stylus.
then there shows 3 colored screen and thats all. i even waited more than 30 minutes, but nothing happened.
i tried all this with radio version 1.47.30.10 too, but its the same result.
what im doing wrong?
Sorry for the late response. You must name it "HERMIMG.nbh" not "HERMING.nbh"
You did everything else right though. Once you rename the file properly and return to the color band screen, there will be on screen instructions.