Hi all,
I'm an absolute newbie here and have been using a Dopod 818pro for a while now with WM5 preinstalled onto it. While browing this site I came across a few WM6 roms that I tried to upgrade my phone with after trying the HardSPL method mentioned in the forums.
I've now landed myself into a predicament. My phone is now stuck to the 3 colored screen. Red, Green, Blue with IPL 2.15.0001 and SPL 2.15.0001. If I connect it to my laptop via USB cable, it says USB in the bottom left corner of the phone otherwise nothing else.
What I did:
-Had been using WM5.
-Downloaded "Update_Package.zip" and unzipped it.
-Connected my device to the computer.
-Backed up all data using Activsync 4.1
-Ran HardSPL.bat from HardSPL G4 folder
-The computer said it has been a success.
-Downloaded this WM6 Rom - "[wm6]Prophet ShadoW 1.0 Touch Edition"
-Flashed the nk.nbf file using ROMUpdateUtility_NV_G4.exe
-Said successfully done that.
-Ever since I am not able to do anything with my phone, its stuck at the 3 color page with the above mentioned IPL & SPL.
I am not able to connect it to Activsync, If i try HardSPL.bat again, it says no device connected. I also downloaded "[wm6]Prophet ShadoW 1.0 Clean Edition" and tried to flash the nk.nbk file using G4, but got the same 3-color screen after 100% copying...
Please help me upgrade it to WM6 or restore it to WM5.
Thank you,
cc
coolcowboy said:
Hi all,
I'm an absolute newbie here and have been using a Dopod 818pro for a while now with WM5 preinstalled onto it. While browing this site I came across a few WM6 roms that I tried to upgrade my phone with after trying the HardSPL method mentioned in the forums.
I've now landed myself into a predicament. My phone is now stuck to the 3 colored screen. Red, Green, Blue with IPL 2.15.0001 and SPL 2.15.0001. If I connect it to my laptop via USB cable, it says USB in the bottom left corner of the phone otherwise nothing else.
What I did:
-Had been using WM5.
-Downloaded "Update_Package.zip" and unzipped it.
-Connected my device to the computer.
-Backed up all data using Activsync 4.1
-Ran HardSPL.bat from HardSPL G4 folder
-The computer said it has been a success.
-Downloaded this WM6 Rom - "[wm6]Prophet ShadoW 1.0 Touch Edition"
-Flashed the nk.nbf file using ROMUpdateUtility_NV_G4.exe
-Said successfully done that.
-Ever since I am not able to do anything with my phone, its stuck at the 3 color page with the above mentioned IPL & SPL.
I am not able to connect it to Activsync, If i try HardSPL.bat again, it says no device connected. I also downloaded "[wm6]Prophet ShadoW 1.0 Clean Edition" and tried to flash the nk.nbk file using G4, but got the same 3-color screen after 100% copying...
Please help me upgrade it to WM6 or restore it to WM5.
Thank you,
cc
Click to expand...
Click to collapse
(P.S. Your HARDspl failed, Activesync verion not update..... )
Reference solution.....
1. go upgrade your activesync (4.5 probably),
2. go to this thread >> http://forum.xda-developers.com/showthread.php?t=353547,
3. follow the recovery method....
a. download NVID,
b. force Prophet to Bootloader MAUNALLY (VERY IMPORTANT, see how to in that thread),
c. Connect to PC,
d. flash NVID to WM5 ( splash screen will be changed),
e. active sync connected,
f. use the tool in the thread and flash with ease....
just for your reference .. hope it helps..
SD card not detected
Thanks a ton dioxda2 for your prompt response, I was (with your assistance) able to flash my Dopod 818 pro and started using PV_4.0.0.0.6_Touch ROM.
After using it for a few days, I got into a problem:
-Was using the PIMBackup utility from the phone itself and was trying to backup my SMS'es to a folder in the storage card.
-Upon finishing the backup, I went to the folder in the storage card to see the file.
-The folder was completely empty, I lost the data that I had in that folder as well.
-I switched off my phone and restarted it again hoping that it'll come back, but now this time, my phone did not detect the storage card at all.
-Since that day, I have been following threads on the same issue and using the solutions provided, but unable to get my phone to detect the storage card.
-I tried to use another SD card but even that one is not detected.
-I formatted my SD card and tried, but no detection.(after backing up data)
-I tried to change ROM and flashed back to "RUU_Prophet_220734_2207114_024721_NVID" but still not able to see storage card.
-I tried to delete the omap850 and sdbus dll files but unable to delete them even with the Resco Explorer (error- files in use, cant delete them)
-I tried flashing to other roms and soft resetted as soon as it started to install cab files after the PIN code request, but still no progress.
-Changed the registry key "disablepowermanagement" to 1, but still no detection of storage card.
One thing I notice is:
-Phone ON, If I switch off the backlight by pressing the power button for a second, and then insert the SD card, the backlight automatically comes on. Which means that my phone detects that movememt.
Please Help!
CC
Try a different ROM.
Also, check if there is any dust in the SD card slot.
Thanks l3v5y for your response.
I tried a different ROM, but the problem still persists. Also tried clearing the SD card slot of dust by blowing into it a few times. Unfortunately, the phone still has the same problem. It reacts when I insert the card into it as the backlight comes on, but cannot see the storage card option in the drop down menu in file explorer.
From the Memory option in settings, it says memory card - not installed. Any other suggestions?
CC
Thanks guys for trying to help me out on this issue. The memory card starting working fine one fine day after I blew into the memory card module a few times. I didnt face this issue again. It must've been dust.
Thanks a lot again..
CC
Related
Hi there!
I read a lot in the wiki and am not now to windows mobile and upgrading (had an XDAII before.)
I bought a MDA vario II, containing WM5.
It had a simlock.
At first i wanted to install WM6 with the official t-mobile update and the unlock it.
I am using win XP, so no problems there.
Activesync found the vario, i started the update-prog... found the vario.. start.
then the vario turns off.
i tried this a few times, it turns off, active sync isn't connected any more. no update.
As the device had a simlock i used the unlocker provided here, it worked good, i can use my E-plus card now.
This worked nearly as the update (same style, but as the device went to some bootloader style in the meantime everything worked.)
I then tried again to install the official update, same thing.
It sometimes seems to be stuck in the tri-color start window when trying, i have so softreset it then...
Then i tried to upgrade via sd-card (tutorial from the wiki (http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing) ).
I extracted the files from the .exe update program.
I saw that the nbh file was too small to contain all the data, so i fetched the schnaps rom and extracted the .nbh fiel from there to updrage to this version.
EDIT: i also extracted the .nbh files from the internal RUU_inside.exe file and tried both.. doesnt work either.
The proglem is that the update doesn't start after softresetting.
Trying to start the bootloader ("start the bootloader (hold Ok button on left side and POWER button at same time and stick with stylus in RESET on bottom).")
brings me to the tri-color bootloader window.
It says:
HERM300
IPL-1.01
HERM300
SPL-1.40.Olipro
Serial
It does not start the updrage file...
what am I doning wrong?
I thought everything should work like this
Tahnks in advance!
Cholera
make sure the card is formatted to fat32, and you renamed the file to HERMIMG.nbh, you might also want to update your hardspl
I checked the type and saw that it was fat (16). I reformated the card and copied the image file once again on it.
I renamed it (again) and restarted with the bootloader.
a second or so it says 'loading' on a white screen, but after that it is again in the tri-color bootscreen as before.
This happens with all 3 tested romupdates..
I will try to update my hardspl to 2.10 Olipro tomorrow, when i am back at home..
will this really help??
Any other suggestions?
I have just tried flashing WM6 on to a Friends QTEK 8500, it went wrong Doh!!!.
I had already last Friday put on it the version with non wroking GPRS and this went without issue. I then reflashed my own one with a GRPS working version (went without a problem) and then tried his. I can get it into the boot loader screen but nothing else. I have tried SD card flashing (3 cards) 1x 512MB Card and 2 x 2GB card all formatted as FAT32 with file on the root the phone searches for it but doesnt find it.
Please any advise.
vallancen said:
I have just tried flashing WM6 on to a Friends QTEK 8500, it went wrong Doh!!!.
I had already last Friday put on it the version with non wroking GPRS and this went without issue. I then reflashed my own one with a GRPS working version (went without a problem) and then tried his. I can get it into the boot loader screen but nothing else. I have tried SD card flashing (3 cards) 1x 512MB Card and 2 x 2GB card all formatted as FAT32 with file on the root the phone searches for it but doesnt find it.
Please any advise.
Click to expand...
Click to collapse
First of all, REMEMBER, your phone is NOT bricked until it goes to BOOTLOADER mode.
Have you made SuperCID before flashing? What firmware are you trying to flash via bootloader mode?
Erofich said:
First of all, REMEMBER, your phone is NOT bricked until it goes to BOOTLOADER mode.
Have you made SuperCID before flashing? What firmware are you trying to flash via bootloader mode?
Click to expand...
Click to collapse
When you say booloader mode what does that look like. At the moment if I reboot the phone I get the HTC Mobility windows by Erofich screen.
When you hold down camera and record button and then power on the device I get brifely the white scrren looking for SD card it then goes to the tri-colour screen and does nothing.
I beleive I have CID it as I did the same on this as I did on mine i.e. ran the unlock according to the sticky.
I than put on this
Windows Mobile 6 AKU 0.5.0 (5.2.1711 Build 18165.0.5.0) WWE v5c
Yours i beleive (excellent work by the way)
and it all worked fine bar GPRS I relay needed GPRS so I used
http://forum.xda-developers.com/showthread.php?t=368715
using the clean one which updated fine on my phone but when i tried it on my friends it fell over at about 83% I followed the recovery intructions but this did not work.
When you get into bootloader screen by pressing RECORD and CAMERA buttons, then you MUST flash back to the STOCK ROM first. You can't flash any custom WM6 at this point. Only AFTER you have the stock ROM flashed, you can use SDA_ApplicationUnlock.exe to app unlock the phone, and copy the SoftSPL into the phone. Then run SPL.lnk.
To summarize: The built-in bootloader CANNOT flash WM6 and can ONLY flash a stock ROM. Once you go back to stock, you can then try to flash WM6 again. Anytime a flash fails, you must go back to stock first, then try again.
GnatGoSplat said:
When you get into bootloader screen by pressing RECORD and CAMERA buttons, then you MUST flash back to the STOCK ROM first. You can't flash any custom WM6 at this point. Only AFTER you have the stock ROM flashed, you can use SDA_ApplicationUnlock.exe to app unlock the phone, and copy the SoftSPL into the phone. Then run SPL.lnk.
To summarize: The built-in bootloader CANNOT flash WM6 and can ONLY flash a stock ROM. Once you go back to stock, you can then try to flash WM6 again. Anytime a flash fails, you must go back to stock first, then try again.
Click to expand...
Click to collapse
I am trying RUU_STAR100_3.6.251.0_02.67.30_QtekEUR_Ship I believe this is an original version 5 rom?
GnatGoSplat said:
you can use SDA_ApplicationUnlock.exe to app unlock the phone
Click to expand...
Click to collapse
This method works on Cingular ROM only, not Qtek.
vallancen
Hold CAMERA and RECORD button and press power button. When it goes to Bootloader tricolor mode connect your device to PC and run official Qtek 8500 RUU. Then make a reg (app) unlock:
Download regeditSTG2 which is digitally signed: http://4pda.ru/forum/attach/387522/regeditSTG2.zip
Then install it and change some registry values:
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 2
-> change to 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 16
-> change to 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 128
-> change to 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101a": Dword = 1
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101b": Dword = 1"
Click to expand...
Click to collapse
copy SoftSPL to the root of your device and run SPL.lnk
Then run WM6 RUU
Erofich said:
This method works on Cingular ROM only, not Qtek.
vallancen
Hold CAMERA and RECORD button and press power button. When it goes to Bootloader tricolor mode connect your device to PC and run official Qtek 8500 RUU. Then make a reg (app) unlock:
copy SoftSPL to the root of your device and run SPL.lnk
Then run WM6 RUU
Click to expand...
Click to collapse
When I plug into PC (XP SP2) and run the Qtek 8500 RUU it just times out and says it cant find device.
vallancen said:
When I plug into PC (XP SP2) and run the Qtek 8500 RUU it just times out and says it cant find device.
Click to expand...
Click to collapse
I have two phones one did work and one did not the one that worked shows version 1.02 on the tri colour screen the one I am having problems with shows 3.06 not sure if this is relevant.
Try removing the battery for about 30-seconds (or just removing the battery cover) and then put it back on. With the phone OFF, hold RECORD and CAMERA and plug in the USB while holding those buttons. It should go to the Bootloader. Run the QTEK RUU immediately after doing that.
If you sit at bootloader very long (more than a minute or so), for some reason it times out and the RUU won't work. It could be that's what's happening.
GnatGoSplat said:
Try removing the battery for about 30-seconds (or just removing the battery cover) and then put it back on. With the phone OFF, hold RECORD and CAMERA and plug in the USB while holding those buttons. It should go to the Bootloader. Run the QTEK RUU immediately after doing that.
If you sit at bootloader very long (more than a minute or so), for some reason it times out and the RUU won't work. It could be that's what's happening.
Click to expand...
Click to collapse
Tried that a couple of times just to make sure I was doing it correctly it goes into the tri colour screen I pressed the reflash option on the PC 1 second later this then sits there for a minute or so and times out "ERROR [260]" the phone did come on and has a USB in the bottom left corner so I presume the connection to the PC is OK.
I have just re-done mine again using the NEO rom (very nice) to make sure I am not going mad and that I did it correctly and this all went without a hitch.
Is there anyway I can get the phone to boot of a SPL on an SD Card I think if I could do this then I could get it back to 5 and start again.
No, it will only boot off the built-in SPL in ROM.
Did you try using the OEM .nbh file, naming it STARIMG.nbh and putting it on the SD card?
GnatGoSplat said:
No, it will only boot off the built-in SPL in ROM.
Did you try using the OEM .nbh file, naming it STARIMG.nbh and putting it on the SD card?
Click to expand...
Click to collapse
Yes tried that made sure formatted FAT32 etc. I know the SD card is ok because if I take my working phone and run the SPL link with the card in my good phone it finds the file and asks me if i want to reflash it. The non working phone with SPL3.06 does not do this.
You are not alone.
The bad news - the person in the post ended up having to exchange the phone.
It could be there's a bug in 3.06 SPL? Seems to be the case because I've flashed bad ROMs many dozens of times on my Cingular 3125 StarTrek and not once did I have any trouble flashing OEM ROM back on it.
Can I write the flash at a lower level with any tools i.e. pdocwrite or seomthing like that?
I don't believe so. Those programs require an Activesync connection (copies files to the phone). You could try the MTTY method, but I don't know if that works on StarTrek. I think it's some kind of terminal access into the bootloader, but what I've said so far is the extent of my knowledge about it.
vallancen said:
I have two phones one did work and one did not the one that worked shows version 1.02 on the tri colour screen the one I am having problems with shows 3.06 not sure if this is relevant.
Click to expand...
Click to collapse
I have a similar problem on a 3125 and the phone reports V4.01. I acquired the phone in this condition, so don't know how that came to be. When I try to update via USB, it tells me I need a newer update tool (to match the 4.01, I assume). What error message are you getting when you try to update via USB?
I have been struggling to flash (again) the great pro V2 rom, but I always used my VMWare based XP windows version on my Vista laptop. Today I could use a genuine XP Laptop and I could make a connection and start the upgrade!
Sounds good? That's what I thought too, until the upgrade stopped at 70% (and I didn't touch anything), because of a connection error. I followed the text on my PC screen and I finally it started flashing again for a few seconds and then my startrek suddenly restarted, but it stops at the first splash screen! I tried to get my device back to bootloader mode (push 2 soft buttons and start), but no bootloader mode, only the 1st splash.
I solved the problem.
Thank you for this thread
I tried flashing a new ROM to my i-mate smartflip and thought I had killed it, but going back to the wm5 OEM as suggested on this thread worked and I still have my phone. Now, am I brave enough to try upgrading it to wm6.1 (or even 6.5) again... Once again, many thanks!
somebody can me give the oem rom because i am same problem too on the secreen 3.06 i cant flashing anytihing rom somebody must me help
On an XP Pro box running activesync 4.5 I cannot update my 8525. I have done the thing on post 1160 page 116 and it now says I have IPL-SSPL by DES and SPL-1.09.ds. I have also tried the Hard SPL V7 and I got the same results. I have installed the latest .net 3.5 and I get the same thing everytime. As soon as the installation gets to the point where you see the progress bar my 8525 goes blank and looses the connection. I was able to update to the OEM 6.1 upgrade but still not able to get Schaps to install. Any ideas? I am going to try it on another PC and see what happens.
If you have Hard SPL installed, don't bother with running SSPL.exe on your hermes. Just put the .nbh file on your sd card & rename to hermimg.nbh. Go to bootloader with sd card inserted & it should automatically load.
IPL-SSPL by DES and SPL-1.09.ds - soft SPL... not as safe as Hard SPL...
My suggestion, follow the steps from post 1160 page 116 again with Hard SPL then try Schapps Skipping
5. extract SSPL-HERM.exe and copy it to your phone.
6. insert sd card and run sspl-herm.exe on the phone.
(make sure to put the sd card into your Hermes of course).
This should work...
Cheers...
OK, I have the hard SPL installed and the same thing still happened, as soon as I get to the option to update the phone and the page comes up showing the status bar my device goes into sleep mode and disconnects from activsync. Just for fun I gave it the three finger solute and it started updating the phone. Then I got a message saying that Schaps 4.30 is not compatible with this phone Error 244 Invalid Model ID. If Schaps 4.01 worked on it, why wouldn't 4.30?
Thanks again for your help.
Sim Unlock your phone then... Here - http://forum.xda-developers.com/showthread.php?t=293665
Then make sure you Hard SPL your phone again... USE THE SD CARD METHOD (directions in previous post)...
Would then try installing Schapps 4.30 using Sd card method too.. Don't forget to skip steps 5 & 6 when updating os...
Cheers...
Hi all,
I have a Hermes here (MDA version from Tmobile UK)
We know the customer has quite literally "fingered" the unit in all ways possible
At the time, he "claimed" to be a windows mobile developer who invented WM5 - dare I say more?
OK so the Hermes is doing the following:
Stuck on Bootloader screen
Herm300
IPL-1.04
Herm300
SPL-2.03
When I do a hard reset via the two soft keys and reset button, the phone boots up with the t-mobile splash with Test Only Not For Sale
Carries on booting, goes through the whole setting up procedure
Then on the reboot, it goes back to bootloader
Now Once I managed to reset and it simply booted in with me using the phone perfectly
The second time I reset, the phone went into a white screen but you could tell it was booting up.
I'm now back in bootloader which refuses to go any further.
Tried running Hard-SPL on it but it can't seem to detect the unit despite it going from Serial to USB
Appreciate any help
On PC (if u use XP), untick "Allow USB Connections" in activesync settings. Put Hermes into bootloader and connect to pc.
Install Hard SPL. Hermes WILL be detected by the Installation program.
Then try installing a new OS, now you should have Hard SPL I'd use the sd card method.
1. Format 2Gb or less sd card FAT32.
2. Copy .nbh file of the rom you want to it and rename to hermimg.nbh.
3 Insert into Hermes and reset to bootloader, follow the instructions....
Should install a new OS and get rid of that "testing only" message.
Cheers...
I follow to your guy , so my device flash :
IPL - Ok
Bootloader - ok
GSM -
It hand on there.
Can you held me now.
My device 's Softbank X01HT, I reflash original ROM (Japanese language)
I have flashed my x7500 before using the Athena_WM6_TMUK_2.35.110.4 rom and that worked. Bootloader said spl v1.0 so I tried the authenaunlocker which said it worked and from then the bootloader said spl 1.2 olipro
I then thought I could update to AGB v3.0 , it seemed like it worked but when it rebooted, it shows some mad pixels like a corrupt image and then seems to boot but with a black screen. I can hear it do the ping it does when it asks to calibrate the screen but it is entirely black :-(
I have tried an sd card method of loading a new rom but it always fails after a few seconds with red numbers 68002 and then goes back to the tri color boot loader.
I tried ultravanilla rom renamed to ATHEIMG.nbh in the sd card (formatted to fat32) and that does the same thing with the red numbers.
have I completely bricked it?
I should say that I'm on Windows 7 and I've tried the MAC change fix but the mtty app doesn't give me a usb port to select, just com1 and com2
I tried the windows exectuable for updating the rom but it always fails with error 244 invalid model id.
here's the images I see
[edit] hurray! the mtty thing worked after I found an old laptop that had xp on it to use, as soon as I had that I downloaded activesync , unchecked allow usb connections and fired up mtty, that had an entry for usb and then I just followed the instructions and was able to change the id, after that, I was able to use the windows exe rom update. I'm now back to where I'm started and have donated to cmonex!
hi i have the same problem with my t-mobile ameo.
the tri-screen even shows the same digits as yours.
did you manage to get a fix for it. or is it totally bricked
If you can enter the bootloader (tricolor screen) it should be possible to reactivate your Ameo. I have flashed my Ameo with wrong SPL ROM too (because it was labled as SPL 1.2 but is SPL 3.5).
If you don't have a WinXP system on your hand, try to flash with SD-card. You need a FAT32 MiniSD card (not SDHC!) or FAT32 MicroSD with MiniSD adaptor.
Format the card and copy the ROM file (for the right SPL!) to it, rename the file from RUU_Signed.nbh to ATHEIMG.nbh. Then go to the bootloader and the Ameo should be ready to flash the new ROM.
If you have a WinXP system you can try to enter the bootloader (remove the MiniSD card before) and then connect your USB cable. The bootloader should change from "Serial" to "USB" and should be ready to flash a new rom.
If your Ameo is fractious you can find some good tutorials here.
Purzelkater said:
If you can enter the bootloader (tricolor screen) it should be possible to reactivate your Ameo. I have flashed my Ameo with wrong SPL ROM too (because it was labled as SPL 1.2 but is SPL 3.5).
If you don't have a WinXP system on your hand, try to flash with SD-card. You need a FAT32 MiniSD card (not SDHC!) or FAT32 MicroSD with MiniSD adaptor.
Format the card and copy the ROM file (for the right SPL!) to it, rename the file from RUU_Signed.nbh to ATHEIMG.nbh. Then go to the bootloader and the Ameo should be ready to flash the new ROM.
If you have a WinXP system you can try to enter the bootloader (remove the MiniSD card before) and then connect your USB cable. The bootloader should change from "Serial" to "USB" and should be ready to flash a new rom.
If your Ameo is fractious you can find some good tutorials here.
Click to expand...
Click to collapse
hi I have the same problem this guy had, I have one question what rom should I use ? can you give me a link please
Purzelkater said:
If you can enter the bootloader (tricolor screen) it should be possible to reactivate your Ameo. I have flashed my Ameo with wrong SPL ROM too (because it was labled as SPL 1.2 but is SPL 3.5).
If you don't have a WinXP system on your hand, try to flash with SD-card. You need a FAT32 MiniSD card (not SDHC!) or FAT32 MicroSD with MiniSD adaptor.
Format the card and copy the ROM file (for the right SPL!) to it, rename the file from RUU_Signed.nbh to ATHEIMG.nbh. Then go to the bootloader and the Ameo should be ready to flash the new ROM.
If you have a WinXP system you can try to enter the bootloader (remove the MiniSD card before) and then connect your USB cable. The bootloader should change from "Serial" to "USB" and should be ready to flash a new rom.
If your Ameo is fractious you can find some good tutorials here.
Click to expand...
Click to collapse
it is not working...
keep your cool
the most important thing is to keep your cool, I've been in trouble before and managed to sucsses, first of all if you are able to go into bootloader you're fine, it seems to mi you flashed wrong spl, the AGB v3.00 is for spl 3.5 only and for what I understand you have spl 1.2, also i my experience you should work with win xp, i have my laptop with 2 os xp and 7, just to do rom loading on my 3 advantages, so if you are able to put your athena in bootloader plug it to your pc your athena sould change from serial to usb, if you can manage that you are almost done, now all you have to do is flash a compatible rom spl 1.2, if you still want agb v.3 you need spl 3.5 and the only way to achive that is to flash athena projet 4 rom, only when that is acomplished you would be able to load an spl 3.5 rom. I hope this help, keep us posted.
hi i have a pc on windows xp sp3 with htc 4.5 it does not pick up my phone bit it will try to load the windows 6 advantage rom,but after it reaches 2 percent ,the phone resets.i have done the same thing as above,i tried to flach a michy 3.5 rom over windows 6 on 1.25,i can get into bootloader but everytime i flash my phone resets.my mini drive is formatted,so could the problem be with the onboard sd card? if so in plain english could someone take me thru it step by step on hpw to access and format that,to see if it makes a difference,many thanks,and a nice contribution to anyone who can help me,and please if you start talking about hot keys,please state which ones,as every key is a hotkey many thanks curzie,if anyone ever needs pc or laptop advice pm me thanks
Who reflash device with this trouble ???
Working - or not ???
flash rom problem
hi, I'm in the same situation and sorry for my English, I have a X7500 I unlocked the radio, and then I installed the 3.0 rom agb all went well, but on the first reboot the system does not start, black screen, if I press the volume button turns on but displays the volume and the touch does not work, I can not make it go into bootloader because it turns on and remains on the flag!
Can you help me?
thanks
Solved
Check out my post http://forum.xda-developers.com/showthread.php?t=2172291