Related
I am running:
SPL-2.40.Olipro
3.35 radio
dcd 3.0.1 rom
I have the verizon xv6800.
I have lost connectivity between PC to phone via USB. Verizon is sending me a replacement.
Is there a way to get it back to stock using a micro SD card (bootloader, radio, rom)?
If not I plan on sending "as is" once I get me replacement--don't really want to do this.
Thanks in advance
hens4th said:
I am running:
SPL-2.40.Olipro
3.35 radio
dcd 3.0.1 rom
I have the verizon xv6800.
I have lost connectivity between PC to phone via USB. Verizon is sending me a replacement.
Is there a way to get it back to stock using a micro SD card (bootloader, radio, rom)?
If not I plan on sending "as is" once I get me replacement--don't really want to do this.
Thanks in advance
Click to expand...
Click to collapse
Have you simply lost connectivity to Activesync? Have you tried another PC? Do you not hear the 'add new hardware' chime when connecting your device? Can you boot into the OS? Can you not flash your phone via the SDcard method to another 2.40 bootloader using ROM? Have you failed in attempting the Wiki Downgrading instructions -- particularly using the Titan relocker?
hens4th said:
I am running:
SPL-2.40.Olipro
3.35 radio
dcd 3.0.1 rom
I have the verizon xv6800.
I have lost connectivity between PC to phone via USB. Verizon is sending me a replacement.
Is there a way to get it back to stock using a micro SD card (bootloader, radio, rom)?
If not I plan on sending "as is" once I get me replacement--don't really want to do this.
Thanks in advance
Click to expand...
Click to collapse
Here is the answer:
1. Format your MicroSD card to FAT32
2. Extract the .NBH you desire to flash (use winrar) from the exe or zip and put it on the microsd card, rename it from RUU_signed.nbh to TITAIMG.nbh
3. Put the MicroSD card in your phone reboot to the BOOTLOADER screen (camer+power+reset) it should then start updating with the .NBH on the SD card and the procedure should begin automatically.
-Sayajin
I think if he uses the sd card method above he will have problems. my understanding is that the stock rom will freak out with olipro 2.40. What he really needs to find out is if it is possible to relock without his USB port functioning. then the sd card method will work to flash a stock rom.
on a related question to the one asked by the OP, can a whole ROM be flashed using an SD card, including the radio? I think I read in the past that flashing radio firmware via SD was very difficult and troublesome...
Like maccaberry mentions, will the stock rom "freak out with olipro 2.40?" Is is possible to flash stock rom and relock from micro SD card?
I have tried several USB cables/PCs and it is just not activesync--troubleshooted with Verizon for 2 hours, the problem appears to be hardware related.
After creating this thread I did read up a bit on the wiki, and was going to try using instructions there, but the part about "the stock rom will freak out with olipro 2.40" has me a bit hesitant to flash stock. If I don't get a solution to update bootloader from micro SD, once I get my replacement and activate it I might try flashing to stock even with olipro 2.40--I am sending it back so if it does get messed up I just have to hope verizon does not come back knocking on my door.
hens4th said:
I have tried several USB cables/PCs and it is just not activesync--troubleshooted with Verizon for 2 hours, the problem appears to be hardware related.
Click to expand...
Click to collapse
You still haven't stated whether or not you hear a chime and/or see a change in the hardware devices list on your PC when your OS is loaded on your phone if you and you plug it into your PC.
hens4th said:
After creating this thread I did read up a bit on the wiki, and was going to try using instructions there, but the part about "the stock rom will freak out with olipro 2.40" has me a bit hesitant to flash stock.
Click to expand...
Click to collapse
Via the SDcard method, try to flash your device to another 2.40 bootloader using ROM. So that you don't need to be concerned over radio incompatbilities (if you do have the correct 3.35 radio installed for your DCD 3.0.1 ROM) you can try to reflash again with a build from DCD or a ROM with my kitchen. Or you can try one of the older OS/3.16 radio ROMs which also use 2.40. Each of the OS and radio ROMs can be flashed from the SDcard.
I'm sorry, but I wasn't clear in my first post that you do need an active USB connection to change the bootloader and that is why I asked if you could boot into the OS, heard your PC chiming on new hardware connected, or had attempted to reflash your phone to another ROM (or same ROM again) via the SDcard. Also, have you tried a hard reset on your phone?
The issue may be hardware but more than likely it is a software problem on your device or PC.
miguelfp1 said:
on a related question to the one asked by the OP, can a whole ROM be flashed using an SD card, including the radio?
Click to expand...
Click to collapse
Yes, any ROM portion should be able to be flashed via that method. On multiple times I have flashed a separate radio ROM without issue.
Keystone said:
You still haven't stated whether or not you hear a chime and/or see a change in the hardware devices list on your PC when your OS is loaded on your phone if you and you plug it into your PC. Via the SDcard method, try to flash your device to another 2.40 bootloader using ROM. So that you don't need to be concerned over radio incompatbilities (if you do have the correct 3.35 radio installed for your DCD 3.0.1 ROM) you can try to reflash again with a build from DCD or a ROM with my kitchen. Or you can try one of the older OS/3.16 radio ROMs which also use 2.40. Each of the OS and radio ROMs can be flashed from the SDcard.
I'm sorry, but I wasn't clear in my first post that you do need an active USB connection to change the bootloader and that is why I asked if you could boot into the OS, heard your PC chiming on new hardware connected, or had attempted to reflash your phone to another ROM (or same ROM again) via the SDcard. Also, have you tried a hard reset on your phone?
The issue may be hardware but more than likely it is a software problem on your device or PC.Yes, any ROM portion should be able to be flashed via that method. On multiple times I have flashed a separate radio ROM without issue.
Click to expand...
Click to collapse
Keystone thanks for you help...I did do the Device manager check...nothing. Several hard resets were done (memory card in/memory card out). I will try you suggestion about trying a different ROM (or same ROM again) that is made for 2.40. My radio is 3.35.04.
Is it a true statement that the Verizon stock rom/radio will NOT work with 2.40?--I could try this but like I said before I am a little nervous since I know I can't fail over to using USB to PC to help my situation.
You need to flash via the SD card as they say. Put whatever version ROM that goes along with your current radio version. Then once you get it up and running you should be able to connect via activesync and run Titan Relocker to get the 1.30 SPL loaded and 2.40 removed. Then you have a choice to leave it stuck there and return it like I done with one once, or you can flash the stock ROM and radio. There is a chance you can do that from the SD aswell incase your pc fails to pick it up again while in bootloader mode. You'll have to get someone elses input on if that part will work or not.
By the way, the stock ROM isn't your real worry. It's the 2.40 bootloader that will get everyones attention. So you really need to go ahead and properly flash and hope activesync will connect.
Is it a true statement that the Verizon stock rom/radio will NOT work with 2.40?--I could try this but like I said before I am a little nervous since I know I can't fail over to using USB to PC to help my situation.
Click to expand...
Click to collapse
You CANNOT flash a stock (verizon signed) rom with 2.40 period. You must relock the phone back to the stock bootloader, and only then can you flash the verizon signed roms.
Key,
You seem to be the expert with SD flashing. Maybe you know a mehtod he can use to get the bootloader on without USB. What I fear is that his USB hardware is fried. In that case, even a flash of a olipro 2.40 compatible rom is still leave him stuck where getting back to stock is concerned. I notice that the bootloader uses a similar software as the roms for loading onto the device. Is is possible to get a bootloader loaded via sd card. I have a feeling it is not possible because the olipro's all use a two step process.. 1st they load a soft (temporary) SPL and then 2nd they load the hard SPL. I have read elsewhere (by ImCoKeMan) that you should not try to run the unlocker via RUU so I assume SD flash version would also not work.
Hens,
If Key cant help us here you might want to pm ImCoKeMan over at ppcgeeks and ask him if the relocker can be loaded via SD card.
Do you have insurance? The device might have an accident with a drop from a 3 storey building that will erase the bootloader altogether..
Finally, you could donate the device to Madman34. He is looking for bricked phones for JTAG experimentation. http://forum.xda-developers.com/showthread.php?p=2019937#post2019937
I was looking into that before I posted my other reply. The one concerning thing about that is when I decompile the titanrelocker.exe file there was a relocker.nb and a 1.30 spl nbh file. I'm pretty sure both are needed, then again I could be way off base. The cool thing would be to get that relocker.exe to run on our mobile device. If that would work it would be easy to set up the SD card to autorun it once WM booted up.
Three story drop huh.... I was thinking Popcorn bout 10 seconds and
how long should this method take mine has been loading for 20min
I spent all day yesterday researching the DCD upgrade until I thought I was ready - boy was I wrong. I'm not computer challenged! I've been writing FW for over 20 years. Things shouldn't be this hard. Anyway, here's what i did:
1) Downloaded olipro 2.4 (except somehow I got 1.2 - not really sure how that happened). Installed it and everything was fine (expect it saysSPL-1.20.Olipro)
2) Downloaded DCD_3.0.1_Alltel.exe and tried to install. It appeared to work, except I never got to customization screen and when the phone re-booted, I just go the Alltel splash screen.
3) Tried to soft-reset, same problem
4) Tried a hard-reset, same result
5) Went into the bootloader and notice I was at 1.2 instead of 2.4, so I downloaded Hard-SPL-MFG.exe (which I believe is the code name for Olipro 2.4) and tried to run it. The batch job fails because it can't talk to my phone (says no device detected) I suspect this is because the phone cannot run ActiveSync.
6) Then I read that 2.4 should be used for GPS ROMs and not for non-GPS, So I thought I needed a non-GPS version of the ROM. So I downloaded DCD_Titan_3.0.0_Alltel.exe and tried that. This also appeared to work (dl to 100% and the phone reset). But again the phone hung at the Alltel splash screen (now it says "no Radio")
7) I'm begining to panic. I trie to download the original Alltel ROM, but they've just put up a new version. So I try RUU_TITAN_ALLTEL_WWE_3.35.671.9_RS_TITAN_03.37.20_Alltel_2.01_AM_PPST_Ship.exe. It causes the phone to reset after downloading 12%. Then stops with a "Command Error"
8) Finally I decide the bootloader must be hosed, so I tried to use the re-locker. Titan_Relocker.exe. This also will not copy the files (due to no ActiveSync) so I extract the files and try to run the RUU directly. Still no joy, the download immediately goes to 100% and when the phone resets it still says SPL-1.20 Olipro.
9) Searching a little more I found the microSD upgrade option. So I copied each of the NBH files (one at time of course) the the root directory and renamed them TITAIMG.nbh and reset into the bootloader (yes, I formated to FAT32 first). The loader never seemed to even ready the SD. It never asked if I wanted to upgrade.
So, here I am. Stuck with a phone that only seems to be able to run the bootloader. The BL does change between USB and serial when I un-plug and plug the USB cable. I can boot to the Alltel splash screen - it says "No Radio". The other red letters that used to appear when the HTC splash appeared are gone.
Any advice? I'm pretty desparate.
Jerry
[email protected]
Pop Out the Battery for a minute
Have you tried popping the battery out for about a minute while its not plugged in yet?
Your problem is you didn't read the instructions carefully enough.
First, you never should have flashed a 3.x.x ROM without making SURE you properly had the 2.4 bootloader installed.
Second, you tried flashing a 3.x.x ROM BEFORE updating your radio to 3.35.04. It says in numerous threads as well as on the first page of the thread that NO radio is included.
What appears to have happened, is you have a 3.x.x rom installed with no radio, and the 1.2 bootloader which can't even boot 3.x.x roms.
My question to you is, have you ever unlocked this phone before or before all of this were you running stock? If you still have the stock bootloader installed and not 2.4, then you need to find the STOCK alltel radio AND rom. You then must flash the stock alltel radio, followed by the stock rom. All you need to do is plug the phone in with usb, manually enter the bootloader and run the RUU's for each.
Once you get your phone back to stock and it boots, only then continue on to reflash. Now, this is VERY important...DO NOT attempt to install any 3.x.x rom without first making SURE you have the new bootloader installed correctly, and second, running the sprint update to get the 3.35.04 radio installed.
Ranger093 said:
Have you tried popping the battery out for about a minute while its not plugged in yet?
Click to expand...
Click to collapse
Yes, numerous times. Sorryy I didn't mention this in my post.
Your problem is you didn't read the instructions carefully enough.
First, you never should have flashed a 3.x.x ROM without making SURE you properly had the 2.4 bootloader installed.
Agreed, but what is done is done
Second, you tried flashing a 3.x.x ROM BEFORE updating your radio to 3.35.04. It says in numerous threads as well as on the first page of the thread that NO radio is included.
I thought the DCD_3.0.1_Alltel.exe image contained the radio. Obviously I was wrong.
What appears to have happened, is you have a 3.x.x rom installed with no radio, and the 1.2 bootloader which can't even boot 3.x.x roms.
My question to you is, have you ever unlocked this phone before or before all of this were you running stock?
I was running stock.
If you still have the stock bootloader installed and not 2.4, then you need to find the STOCK alltel radio AND rom.
I'm pretty sure I don't have the stock bootloader. It says SPL-1.20.Olipro
You then must flash the stock alltel radio, followed by the stock rom. All you need to do is plug the phone in with usb, manually enter the bootloader and run the RUU's for each.
I've tried the latest stock ROM RUU_TITAN_ALLTEL_WWE_3.35.671.9_RS_TITAN_03.37.20_ Alltel_2.01_AM_PPST_Ship.exe but it re-boots the phone while downloading (@ 12%)
Once you get your phone back to stock and it boots, only then continue on to reflash. Now, this is VERY important...DO NOT attempt to install any 3.x.x rom without first making SURE you have the new bootloader installed correctly, and second, running the sprint update to get the 3.35.04 radio installed.
IF I get the phone back as stock, I doubt I will EVER try to re-flash it again.
Here's the link to the old Alltel Rom and Radio. http://www.htcamerica.net/support/ppc6800/software-downloads.html
If that doesn't work for you, you should be able to load up any of the older 2.x radios with an older dcd ROM, then upgrade to OliPro 2.4, then load the new Alltel Radio and Rom which you already have.
I've had this exact same problem (almost) except with Verizon (shouldn't be any difference whatsoever.) With the "No Radio" error messages and such -- and the key is the microSD flash. The reason it didn't recognize the image is (probably) because of the way you formatted your SD card. It can't be formatted in windows and work, you can't use a quickformat, and it has to be unconditional. The /x dismounts the volume so the volume is totally accessable. /a:512 tells it something about how many sectors to use or something -- idk -- but it works.
Open a DOS window (start, run, type "cmd")
this is your command:
format x: /fs:fat32 /u /x /a:512
Replace x: with the drive letter of your microSD card. Be sure of this.
Other than the drive letter type it exactly as is says.
1. Run the titan relocker.
2. Rename the stock alltell rom(s) as TITAIMG.NBH one at a time if there is more than one (radio and rom, unless they are together) and put them on your microSD one at a time (in the root directory.) Order shouldn't matter, but I ran ROM then Radio. Open bootloader and make sure it's not Olipro. The screen should pick up the image on the microSD card.
Flash, after 100% remove the battery, replace, and then hard reset.
These are the steps that I took with my Verizon issue and it worked perfectly.
Once this is done don't give up on the modified ROMs. Sometimes when I upgrade friends phones it won't let me go directly to 2.4 Olipro. I have to flash 1.2, then a 1.2 compatible RADIO and 1.2 compatible ROM. Then I have to flash to 2.4 unlocker, 2.4 compatible radio (usually 3.27) and then a radio 3.27 compatible ROM (pref. DCD 2.3.2.) After which, I can flash the stock Sprint 3.35 (without ever booting the OS) and then flash the DCD 3.x.x ROM.
Hope this helps you out --
I've tried the latest stock ROM RUU_TITAN_ALLTEL_WWE_3.35.671.9_RS_TITAN_03.37.20_ Alltel_2.01_AM_PPST_Ship.exe but it re-boots the phone while downloading (@ 12%)
Click to expand...
Click to collapse
The latest stock alltel rom is a 3.x.x rom as it states in the file name...3.35.671.9
As I said before, you need the 2.4 bootloader to boot any 3.x.x roms.
If you have unlocked with 1.20, then you have a little more work cut out for you.
This is what you need to do:
Since you have 1.20 and you can't get an activesync connection, you need to first flash an old custom alltel rom (NOT the stock alltel rom). DO NOT flash any dcd 2.x.x rom as the poster instructed above as it also requires olipro 2.4. I believe if you search for dcd's 1.70 kitchen and roms you'll find one there. You also must flash radio version 1.40. THIS will allow you to boot up into windows mobile and finally get an activesync connection. Since you can't boot right now, your best bet is to flash both of these with the microsd card.
The next step is now that you can boot into windows and have an activesync connection, you need to RELOCK your phone using the titan relocker, follow the directions carefully...and if you get stuck in the bootloader after the relock, you need to use the titan exitbl application that will force you out of the bootloader.
If all is well you now should have olipro 1.06 (stock bootloader) back on the phone. Here's the catch, you won't be able to boot the 1.70 rom anymore...so now you must manually enter the bootloader (power+camera+reset) and NOW flash the stock alltel rom and radio again with the microsd card. Once you flash the stock rom and radio, you will now have the stock bootloader, stock rom, and stock radio.
Now just unlock with olipro 2.4 and MAKE SURE it is on there correctly. Then run ROM RUU_TITAN_ALLTEL_WWE_3.35.671.9_RS_TITAN_03.37.20_ Alltel_2.01_AM_PPST_Ship.exe which DOES include the 3.37.20 radio as it also states in the file name. After that, you are free to flash a dcd alltel rom, as you will already have the proper bootloader and radio.
gcincotta said:
DO NOT flash any dcd 2.x.x rom as the poster instructed above as it also requires olipro 2.4.
Click to expand...
Click to collapse
excuse me, but if you read my directions in order, that's not what it says to do in the section about fixing his current situation.
AND,
If you carefully read what I had to say about future upgrades:
"...Then I have to flash to 2.4 unlocker, 2.4 compatible radio (usually 3.27) and then a radio 3.27 compatible ROM (pref. DCD 2.3.2.)"
In no way do I mean to flame, but please read.
Thank you kindly
dizwayney said:
Here's the link to the old Alltel Rom and Radio. http://www.htcamerica.net/support/ppc6800/software-downloads.html
If that doesn't work for you, you should be able to load up any of the older 2.x radios with an older dcd ROM, then upgrade to OliPro 2.4, then load the new Alltel Radio and Rom which you already have.
Click to expand...
Click to collapse
Thanks dizwayney. This was the link I needed. From here I was able to re-flash the original Alltel 2.14 ROM and radio. It is back to it's old self (well - except for all my data).
Oddly enough it still says SPL-1.20.Olipro for the bootloader. Oh well, as long as it boots I really don't care.
One other thing I learned during this adventure. You can't flash form a 4GB microSD, it must be 2GB or less (in order for the 512 byte allocation to work). If I'd known this earlier it might have saved a lot of time.
Again, thanks to everyone who responded.
In no way do I mean to flame, but please read.
Thank you kindly
Click to expand...
Click to collapse
I strongly suggest you take your own advice and read, because I wasn't even referring to you. I was referring to the post before yours.
Cheers
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
I went from stock to 3.2.0 / Radio 3.42.02.. no problems.
I have not loaded 2.42.30 (I prefer to use the radio version released by HTC for this device.. 3.42.30 was released for another device and ported.. although it seems to work for everyone.)
I HAVE read that for radio 3.42.30 you need SPL 1.20 for USB Flashing.
gc14 said:
Yeah 1.20 is needed to flash these radios via USB. Just need to put 2.40 back when you're done.
Click to expand...
Click to collapse
Based on that.. I assume SD flashing is ok with 2.40.
scotcha12345 said:
... (maybe thinking the Radio needed to be installed for it to get through)....
Click to expand...
Click to collapse
Yes! This is well documented.. a common issue.
If you flash the Rom without a compatible radio.. you will get stuck on the verizon screen... I suggest flashing the ROM AFTER the radio.. since you flashed the Rom already... when you get the radio working, Reflash the ROM.
Did you flash the radio via SD Card or USB?
Did it show a progress bar while flashing?
Let us know how your attempting to flash the Radio (USB or SD) With specific steps (held buttons X, Y, and Z.. saw this message, pressed this key.. saw this on the screen) .. and someone will let you know what you might be doing wrong.
Also.. dont forget to run the carrier cab when your done.. This is worth mentioning since it's the most common issue once the device boots and you cant program the phone, or make data / voice connections.
scotcha12345 said:
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
Click to expand...
Click to collapse
Can you get to the bootloader by holding down camera power and pushing the reset button? If so, you can flash the radio with the SD method found in the wiki. just put the radio on the sd card in the proper format and enter bootloader and it should correct your problem.
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Responses
Hey guys,
Thanks for the responses and suggestions.
1) At the moment he doesn't have an SD card aside from the SDHC, so he couldn't do that until he purchases one. Good idea though if nothing else works
2) When pressing the camera/power/reset he's in the SPL 2.4 bootloader screen, he's going to try your suggestion of downloading Sprints and upgrading.
3) I'll ask him procedurally what else he has tried, what error he gets for recording. No doubt you were correct about uploading the Radio before the ROM
I've actually flashed my phone exactly the same way he has so that I can try to experience the same problems, and try to figure it out myself.
Bingo
Hey,
The Sprint ROM .exe was the answer. Very smart, thanks again for helping us both out. Was getting a little nervous for about 2 minutes.
useful=helper++
I did the same thing. Thank you very much...saved my butt!
BC
its alive
spreeway said:
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Click to expand...
Click to collapse
you saved my titan...thanks guy!
Before I start I did searches and looked at all the posts that apply to this situation and could not find anything. After spending many hours searching decided to try posting.
Situation:
I have a Verizon xv6800 that I am trying to update so I can have GPS. The first thing I did was to flash the OLIPRO 2.4 ROM. After the flash was complete everthing seemed OK but the power button no longer worked to turn the phone on. Also if you called the phone it would not ring.
The next thing I tried was to use an SD card to load nuespl 2.47. Again everything seemed OK but the power button still did not work.
Then I loaded OLIPRO 1.2 ROM and now everything seems work perfectly including the power button.
The boot screen verifies that the OLIPRO 1.2 is loaded.
Now I am confused as to which radio I should be using since the "Step by Step tutorial for unlocking your device and cooking your own ROM!!! " post said not to use OLIPRO 1.2.
Can any body tell me the next steps I should do to get an upgraded radio?
Please make it simple since obviously I can't figure it out myself.
Thanks for any assistance.
karter said:
Before I start I did searches and looked at all the posts that apply to this situation and could not find anything. After spending many hours searching decided to try posting.
Situation:
I have a Verizon xv6800 that I am trying to update so I can have GPS. The first thing I did was to flash the OLIPRO 2.4 ROM. After the flash was complete everthing seemed OK but the power button no longer worked to turn the phone on. Also if you called the phone it would not ring.
The next thing I tried was to use an SD card to load nuespl 2.47. Again everything seemed OK but the power button still did not work.
Then I loaded OLIPRO 1.2 ROM and now everything seems work perfectly including the power button.
The boot screen verifies that the OLIPRO 1.2 is loaded.
Now I am confused as to which radio I should be using since the "Step by Step tutorial for unlocking your device and cooking your own ROM!!! " post said not to use OLIPRO 1.2.
Can any body tell me the next steps I should do to get an upgraded radio?
Please make it simple since obviously I can't figure it out myself.
Thanks for any assistance.
Click to expand...
Click to collapse
Ok no worries about the newbie thing. We all were newbies at one time!
First it sounds like the 2.40 flash did not completely go well. So since you are back to 1.20 I would upgrade in this order:
1) First update your radio to 3.42.50. This is the latest radio and seems to help with phone service issues. At least that is what I have seen. You will need the RUU install files so I attaching RUU.zip for this. Unzip this and then when you download the upgraded radio drop that file into this directory and then flash. If successful your phone should display 3.42.50 at boot time.
2) Next upgrade to 2.40 of the unlocker. I am attaching the install I use, so unzip the file and then run it to install/upgrade your phone. If successful your phone should show 2.40 when done.
3) Now you are ready to persue a ROM or kitchen that is GPS capable. There are many of them. I am currently using DCD's 3.26 kitchen but No2Chem also has a 5067 kitchen that is very stable. If you have questions about this process do not hesitate to email me at [email protected].
Steve
I did step one and everything seemed OK. Took several minutes with progress bar and exited normally. The boot screen indicates 3.42.50 as per instructions. But now the phone gets stuck at the white verizon screen. Should I proceed to step 2?
Thanks
Ken
karter said:
I did step one and everything seemed OK. Took several minutes with progress bar and exited normally. The boot screen indicates 3.42.50 as per instructions. But now the phone gets stuck at the white verizon screen. Should I proceed to step 2?
Thanks
Ken
Click to expand...
Click to collapse
Take the battery out and then put it back in. It should boot then. Go to step 2 then.
Steve
Took battery out waited 1 minute and replaced battery. Still stuck at white screen.
Ken
karter said:
Took battery out waited 1 minute and replaced battery. Still stuck at white screen.
Ken
Click to expand...
Click to collapse
Move on to step 2. Quick question...is the current ROM the stock VZW ROM or one from XDA?
Steve
Actually he gave you the instructions backwards. (Tho his method may work, it's just not what the Wiki says to do) You always update the bootloader first, then the radio, then the rom. The new radio requires a new bootloader (hence why it's locking up), go ahead and reinstall BL2.4, if that doesn't work, see if you can find an older non-gps radio, and flash it via the SD card. Once you get back to either an old bootloader and old radio, or a new bootloader and a new radio, then you will have better success getting the rom flashed.
You were fine actually with your original 2.40 install, it will boot once normally, however as soon as it goes to sleep or you turn it off it won't turn back on, a soft reset will get it back up, but it will keep crashing. So at that point you can flash the radio and ROM from the Bootloader screen.
If you can get 2.40 (actually get 2.47 if you can, worse case use 2.40 and upgrade the radio and rom to the new version, then run 2.47 from the pocketpc and it will update you to 2.47 (I just did this yesterday).
So reflash to 2.40 if you can, otherwise do some searching for an old radio (non-gps) and flash it.
Then go back and re-read the wiki, it tells you that you have to flash the bootloader, then the radio, then the rom. It's always in that order for a first time flash. Once thats all done, any future updates should only require a single flash (for radio or rom).
BTC
BillThyCat said:
Actually he gave you the instructions backwards. (Tho his method may work, it's just not what the Wiki says to do) You always update the bootloader first, then the radio, then the rom. The new radio requires a new bootloader (hence why it's locking up), go ahead and reinstall BL2.4, if that doesn't work, see if you can find an older non-gps radio, and flash it via the SD card. Once you get back to either an old bootloader and old radio, or a new bootloader and a new radio, then you will have better success getting the rom flashed.
You were fine actually with your original 2.40 install, it will boot once normally, however as soon as it goes to sleep or you turn it off it won't turn back on, a soft reset will get it back up, but it will keep crashing. So at that point you can flash the radio and ROM from the Bootloader screen.
If you can get 2.40 (actually get 2.47 if you can, worse case use 2.40 and upgrade the radio and rom to the new version, then run 2.47 from the pocketpc and it will update you to 2.47 (I just did this yesterday).
So reflash to 2.40 if you can, otherwise do some searching for an old radio (non-gps) and flash it.
Then go back and re-read the wiki, it tells you that you have to flash the bootloader, then the radio, then the rom. It's always in that order for a first time flash. Once thats all done, any future updates should only require a single flash (for radio or rom).
BTC
Click to expand...
Click to collapse
The issue with reversing steps 1 and 2 is that the Olipro 2.40 does not allow the ability to update the radio ROM. You have to back down to 1.20 and then do the radio. That has been the case for the last two radios I have upgraded to. So that is why I put it in the order I did.
Steve
Ah ok, well, I had 2.40 installed for over a month and have updated my radio 3 times (tho I did it via SD card), I assume you meant it doesn't work via USB (and I remember now seeing posts that talked about that)
I stand corrected. His way should work. Just the phone will not boot properly until all 3 items are updated to GPS compatible files, BL 2.40+ Radio 3.42+, Rom 3.x. Prior to all 3 being updated tho, you should be able to flash from the bootloader, so boot into it and flash from there until all 3 are updated.
Once all 3 are flashed, your phone should work normally.
BTC
BillThyCat said:
Ah ok, well, I had 2.40 installed for over a month and have updated my radio 3 times (tho I did it via SD card), I assume you meant it doesn't work via USB (and I remember now seeing posts that talked about that)
I stand corrected. His way should work. Just the phone will not boot properly until all 3 items are updated to GPS compatible files, BL 2.40+ Radio 3.42+, Rom 3.x. Prior to all 3 being updated tho, you should be able to flash from the bootloader, so boot into it and flash from there until all 3 are updated.
Once all 3 are flashed, your phone should work normally.
BTC
Click to expand...
Click to collapse
Yes via USB since SDHC cards are not supported and I do not have a regular SD card. I really should buy one...they are cheap now.
Steve
I reloaded the original radio using a sd card and now the phone works again. Can I load OLIPRO 2.40 using a SD card? If so how.
Thanks
Ken
Not that I am aware of (tho I don't know everything....), I flashed 2.4 from my PC via activesync, let it reboot, and then had to run out and get a flash card and flash card reader (in order to format it correctly) then was able to flash the radio, and then flashed the rom via Activesync. (I just remembered that I had to flash my radio from SD card, I had completely forgotten until I stopped to remember why I bought the memory card reader)
If you have it working with your old rom, then I would copy 2.47 BL over to your phone in windows and run it, it will flash the bootloader for you (tho it requires a preformatted SD card (not SDHC)). It will offer to format it for you if you can't get it formatted correctly yourself. If it's already in the right format, it doesn't have to be empty as it will just copy the file, reboot, and delete the file automatically. If it's not in the right format and you have stuff on it already, copy it off to your harddrive, then put it back in and it will format it for you. Once it's formatted correctly, it will still work normally in the phone and on your PC, so it's worth it to get the SD card into the right format.
Once 2.47 is installed, boot into BL mode (camera, power and reset button), and then do the rest of the flashing over USB. It will auto-reboot after each flash, so keep going back into BL mode until after you get the rom flashed. Then let it boot normally, LET IT RUN CUSTOMIZATION (pending you are installing DCD's rom) If you are installing another carrier's rom, then never let customization run (unless it's your carrier). Once customization is done running, install your carrier's cab file, this is pretty important or the phone won't properly work, I would do one more soft reset and at that point your phone is all ready to go and you can set it up, and install your programs.
BTC
Billy the Cat
I wish I had known that the power button wouldn't work untill all three steps were complete. Because of that I got concerned that I may have screwed up the phone and started trying all sorts of things to fix it (probably making it worse in the process).
Now that I know how to get back to the original ROM & Radio if something happens I will try again to get the GPS working.
Thanks Billy the Cat and stevefxp
Ken
No problem. I was like you the first time I started to flash my phone, I had just gotten the BL installed and then had to leave, my phone wouldn't stay running so my wife got extremely mad at me because she would call and since the phone wouldn't turn on it would go to VM. It took me a while to get her to appreciate my phone again, til then it was "A huge waste of money" in her opinion.
Since then tho, I have shown her the great features of being able to search for an item on ebay when we are at an auction to get an idea of a item's value before bidding, been able to take pictures and email them to her at no cost (old phone was $.25 per message), and having the GPS makes it much easier to find some of these remote auction locations we go to.
So after all that, shes not screaming at me for buying the phone anymore, tho she still isn't happy I spent the money. Oh well, she fritters more money away than I do, so I don't have a problem buying something that will last me for 2 years with the amount that shes frittered away in a week many times.
BTC
I am still having the same problem with the white Verizon screen. These are the steps I took.
1. Reloaded the original radio 1.30.60 using the SD card approach
phone worked
2. Reloaded the original ROM 1.6.7
phone worked
3. Loaded nueSPL-2.47 using the sd card
Red/Blue/Green screen had:
TITA100
SPL-2.47No2Chem TITAN SPL EVT
CPLD - 9
4. Loaded radio 3.42.50 using the SD card
Verizon white screen has
M 09 P DCAAXOM - 4350
H3B60775B R 3.42.50
D 2.17
The phone now still hangs at the white Verizon screen. I really thought I knew the process but clearly I still do not understand something.
Any help??
every thing is ok, load a gps compatible phone rom like dcd 3.2.6 using the cd card method and it will work after that
I have the 3.2.6 kitchen downloaded from DCD1182 but I can't find the nbh file unless it is the RUU_signed.nbh file and I just have to rename it to TITAIMG.nbh
If that's not it where can I download the 3.2.6 nbh file.
Thanks
Ken
karter said:
I have the 3.2.6 kitchen downloaded from DCD1182 but I can't find the nbh file unless it is the RUU_signed.nbh file and I just have to rename it to TITAIMG.nbh
If that's not it where can I download the 3.2.6 nbh file.
Thanks
Ken
Click to expand...
Click to collapse
That is it.....
You guys are great. The phone is working again and has radio 3.42.50 and ROM 3.2.6 on the white screen so I guess everthing is correct now.
I also loaded the Verizon CAB to get internet and reprogrammed the phone with *228
I have one last question. What happened to the battery indicator in the upper right hand corner?
I really appreciate all the help you guys gave me. I read all the instructions but knowing nothing about what I was doing there is some information that would have been very helpfull if I had only known.
1. If you get in troubble you can reload the original radio and ROM to get the phone working again.
2. You really need to complete all the steps before you can expect the phone to work properly. I kept trying to test the phone at each step to make sure that it still worked. This approach got me in all kinds of trouble.
3. Don't panic if something doesn't seen right just ask the experts on this board. They have a wealth of knowledge on how to get out of trouble.
4. Make sure you have a micro SD card on hand before you start.
5. While it didn't answer all my questions read the WIKI flashing documentation completely before you start.
Again - thank you everyone for helping me to get my phone upgraded.
Ken
you can get the battery by changing the registry.
hklm/software/microsoft/shell/showtitlebarclock.
not sure what all the setting do. mine is set to 0 and i have the battery icon.
alternatively you can use htc home customizer to change the value for you.
Hi I'm looking for some help. I tried upgrading my XV6800 to the windows 6.5 rom but I think I might of messed up. I tried to update my radio first but ran in to issues.
I used Oilpro 1.20 to try and tried to update the radio but along the way messed up while trying an older rom and I'm currently at a Verizon screen with the message "NO RADIO" at the bottom. I'm assuming the radio rom was erased. I might have gotten confused with the roms and used a rom without the appopriate Radio. When I try to flash that rom back to a stock Verizon upgrade it just ends 11% in to the flashing process and the rom update utility returns a Error 290 screen.
Currently I can get the oilpro 1.20 bootloader to still load up but I'm not sure what to do at this point. I tried updating the ROM to DCD's older 3.20 roms, which did complete but I still have that screen coming up. Can anyone give me some suggestions on what I should do next? Any help would be greatly appreciated.
Try using NueSPL 2.47 it's more current
Doesn't have have to be run on the phone itself once inside Windows? The only screen I can get up is the Verizon (splash) screen where it normally lists the rom and radio, or the oilpro boot loader screen. I actually can't get back in to windows to run the nueSPL 2.40.exe file.
Is there a way for me to flash the radio back from a bootloader screen and USB or SD card? The thing is I actually tried to take the 3.42.40 radio and use the Flash Rom Utility to see if it would flash the radio rom back on but even though the process completes successfully, I still get the no radio error so I guess it doesn't work. Thanks for the help, I think I may have been a few of the idiots out there who screwed things up and didn't make sure the radio was up before attempting any rom upgrade.
You should've changed the bootloader first. Your radios that you are trying are not compatible with your bootloader.
Flash an old stock rom via SD, then update your bootloader to 2.47 once you can get back into windows, then update your radio, and then your rom.
Yeah that was one of the first things I've tried a USB update back to the stock Verizon 6.1 ROM, but for some reason it prematurely ends at 11% with the PDA Phone Update Utility throwing a ERROR 290 message. This is the first time this has happened as I've flashed with this same rom tons of times. I've been looking online for the past hour on how to flash the ROM from a SD card if I can't get in to Windows. But all I could find was the USB update utility and it ends at 11% Am I doing it wrong? any ideas would be greatly appreciated.
If you can still get in the bootloader then you should be fine....I would put it manually in bootloader holding power and camera simultaneously and poke the hole to get it into bootloader.
Once you do that plug in the data cable and run Olipro 2.40 or Nue 2.47. It should be able to take after that.
Basics steps to flashing a phone:
correct unlocker-->stock ROM-->custom ROM
Most custom ROMs will not include Radios that why you would run the stock ROM first to install the radio and then run the custom ROM. Alot simpler then trying to update the Radio by itself.
AWESOME! I got it back up, thanks guys. For reference purposes I'm going to restate the problem and solution incase other noobs run in to the same issue.
PROBLEM:
I installed oilpro 1.2 during the process of installing a new radio then a rom. Along the way the rom install failed. I tried to reinstall a stock Verizon rom RUU 3.57 & 3.37 radio but it failed at 11%. I was then stuck at the splash screen with a message that said NO RADIO. I could still get in to the boot loader with the power and camera button. But the stock Verizon rom did not install anymore.
SOLUTION:
I used titan_exitbl.exe to exit the bootloader and I went back to an earlier rom found here, rom 2.09 & radio 1.30. That one actually installed. It seems to have worked. I'm back in windows now but I need to uninstall oil pro 1.2 and get nuSPL 2.47 on there before I move further (it looks like while it's still on the stock RUU won't work for me).
Do you guys know how I would go about uninstalling Oilpro 1.2? Will Titan_relocker do it for me? I'm not sure if installing nueSPL over oilpro will do it.
Use this ROm from Verizon to get the Stock 6.1 back up and running. It's the MR2 rom
http://www.pcdphones.com/phone_downloads.aspx?bid=89&cid=1&mid=287&carrier=Verizon Wireless
Beyond888 said:
AWESOME! I got it back up, thanks guys. For reference purposes I'm going to restate the problem and solution incase other noobs run in to the same issue.
PROBLEM:
I installed oilpro 1.2 during the process of installing a new radio then a rom. Along the way the rom install failed. I tried to reinstall a stock Verizon rom RUU 3.57 & 3.37 radio but it failed at 11%. I was then stuck at the splash screen with a message that said NO RADIO. I could still get in to the boot loader with the power and camera button. But the stock Verizon rom did not install anymore.
SOLUTION:
I used titan_exitbl.exe to exit the bootloader and I went back to an earlier rom found here, rom 2.09 & radio 1.30. That one actually installed. It seems to have worked. I'm back in windows now but I need to uninstall oil pro 1.2 and get nuSPL 2.47 on there before I move further (it looks like while it's still on the stock RUU won't work for me).
Do you guys know how I would go about uninstalling Oilpro 1.2? Will Titan_relocker do it for me? I'm not sure if installing nueSPL over oilpro will do it.
Use this ROm from Verizon to get the Stock 6.1 back up and running. It's the MR2 rom
http://www.pcdphones.com/phone_downloads.aspx?bid=89&cid=1&mid=287&carrier=Verizon Wireless
Click to expand...
Click to collapse
Glad to hear you got your phone back up
As far as I know you should be able to just install 2.47 and it will overwrite your old bootloader without problems. I could be mistaken but there isn't really a way to "uninstall" a bootloader, just overwrite it with a different one.
unL33T is correct...just run Nue 2.47 and let it overwrite the old one. 8p
Yeah that's what I thought too, but when I tried to over right it with 2.47 the 1.20 showed up again so I used the titan_relocker tool. Maybe I did something wrong. I'll go recheck, thanks for the replies guys.