i was trying to upgrade the HTC offical ROM. but my hermes was bricked and stuck on the blue windows logo screen now. please help me
(it display NOGSM on the dopod logo screen also)
i have no any idea now and my hermes without the KITL mode
so what can i do .plz help me
hi,
try this :
http://wiki.xda-developers.com/index...pgradeProblems
or :
Problem 4: Device is stuck in bootloader mode (tri-color screen)
* Important : Windows VISTA users need to make a change to their system to successfully use many ROM packages. See Mr. Vanx's guide here
*
If you are using Windows XP or Windows 2000, you MUST have the Microsoft .net framework installed on your computer.
1. Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2. Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
3. Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
4. Open mtty.exe and select "USB" from the dialog box, then hit Ok.
5. You should see a white screen, hit enter and you should see a prompt like this: "USB>"
6. Type set 14 0 (do not copy and paste!!!) and hit enter
7. Soft reset with stylus
8. OS ROM and radio version should be back and OS functional, the unit isn't a BRICK anymore!
9. if it doesn't unbrick, repeat all the steps but with the command set 16 0
I want to add something here that worked for me. Tried steps above but it didn't work. So what I did to get mine going again:
ciaoo kB
kb_lejardinier said:
hi,
try this :
http://wiki.xda-developers.com/index...pgradeProblems
or :
Problem 4: Device is stuck in bootloader mode (tri-color screen)
* Important : Windows VISTA users need to make a change to their system to successfully use many ROM packages. See Mr. Vanx's guide here
*
If you are using Windows XP or Windows 2000, you MUST have the Microsoft .net framework installed on your computer.
1. Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2. Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
3. Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
4. Open mtty.exe and select "USB" from the dialog box, then hit Ok.
ciaoo kB
Click to expand...
Click to collapse
when i go to step 4 and hit OK, the mtty popup a dialog box said "USB port can not open"
Have u tried hard resetting your phone? or maybe u can just go to bootloader mode and flash it with a new rom? this work for me
ocguru said:
Have u tried hard resetting your phone? or maybe u can just go to bootloader mode and flash it with a new rom? this work for me
Click to expand...
Click to collapse
really? i haven't try , i am afarid it will become more serious
but what is your problem previously? why you bricked your phone?
i was trying to upgrade HTC offical ROM and bricked.
THX
as u can see..there are quite a few rom..i had to try every one of them to see which one suites me well..thats how i got my phone bricked
ocguru said:
as u can see..there are quite a few rom..i had to try every one of them to see which one suites me well..thats how i got my phone bricked
Click to expand...
Click to collapse
i read this post
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
my hermes is same as the bottom situation of the above page now
SPL2.03,no boot OS, no GSM, bricked while flashing OS, but my hermes
can not switch to KITL mode , so i have no any idea
do you have any suggestion for me?
THX
turn on your phone..connect your usb cable..see if u have any connections with activesync..
ocguru said:
turn on your phone..connect your usb cable..see if u have any connections with activesync..
Click to expand...
Click to collapse
sorry , but it has no any boot OS thus Activesync can not recognize my phone
Related
I'm sorry for the typical question and thread!I did everything but without result,
for this reason i've decided to make a post
so as i said on title i'm stuck on boot screen,to let you understand
the screen with 4 colors,red,green,blue,white.Now here the point,it seems that i can't resume my phone
from that screen!I've tried as is written here "format a microSD card with FAT32
extract the .NBH file from the rom image you like
rename the .NBH to HERMIMG.NBH and copy it to your microSD card
put microSD card in phone and start it in bootloader (hold Ok button on left side and POWER button at same time and stick with stylus in RESET on bottom)
confirm flashing on screen" but it was useless,nothing happend,when i push the left button ok
and at the same time power and soft reset,the screen change color become gray and appear a write "Loading...."and some numbers above 00068002
to return invain at the beginning screen.I don't know what i wrong and if is there another way to resume it,obviously my activesync don't work.
Here others informations if it can be useful for someone about my boot screen
Red stripe there's written: HERM200 I PL-1.01
HERM200 SPL-1.11
White stripe: Serial
does anyone had my same problem???
Please help me i really need my phone because my work
Thanks a lot
Try flashing from the computer - just start with the phone in Bootloader mode, select force using SSPL and flash whatever ROM you like. Give it a try.
Thanks for the answer!But i've already tried that way without success,maybe bcause there's not connection with the activesync,could be possible?In fact when i try appear an error wich says
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
Check the following:
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC.
Now how can i fix this problem????
Thanks for ur collaboration!!!
Pleaaaaaaaaaaase HEEEEEEEEEEEEELLLLLLLLLLLLLLLLPPPPPPPPPPPPPPPPPPP
I have exactly the same problem !!!
Damn!We gotta find a solution!Hey if you can fix our problem please let me know!And naturally the same for me.Let's keep in touch!
White stripe: Serial
Click to expand...
Click to collapse
This should switch to USB once you plug it in...
Give us a little more info now please:
* what file are you trying to flash
* what RUU are you using
* have you tried connecting with mtty (if you get in, try task 28)
* have you trried hard reset
Just to be clear on my previous post...
1. Put phone in BL mode
2. NOW plug phone into computer (that order is important)
*Phone should now say USB*
3. Launch CustomRUU (should not be a retail RUU)
4. Flash
Dear todd_jg,
first of all thanks to be interesting about my problem,
second yes my phone switch to serial in usb mode,
-regarding the RUU i don't have any idea about it!
-Can u post the right RUU that i should use please?
-Never tryed mtty
-Yes i've tried with hard reset but without result,it send me back to the boot screen
-I did exactly as you said but it was invain!
Use the RUU file from THIS THREAD
Get the nbh file
Drop it into a folder with the RUU
Launch the RUU
Whichever nbh is ok???
tetsuokaneda said:
Whichever nbh is ok???
Click to expand...
Click to collapse
Yes, but if you continue to have problems, you may wish to try a different one or at least post a link where you found it...
I got it!I'm trying right now!I'll let u know immediately!Thanx
Fu.. nothing to do....
here what it said
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
I think that the problem is the connection between the Cpu and the Pda.
tetsuokaneda said:
Fu.. nothing to do....
here what it said
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
I think that the problem is the connection between the Cpu and the Pda.
Click to expand...
Click to collapse
Alright - lets try a task 28 with mtty
You will need to find mtty first (should be a link in the wiki or use search).
The tricky part is getting mtty to see the USB connection... I get it by doing the following
1. With the phone in BL mode and mtty closed, plug it in to the USB
2. Using ActiveSync, manuallyt tell it to check for connected devices (this will get it to start polling the ports)
3. While ActiveSync is still polling the ports, open mtty
4. Where it says connect using... or port... or something like that, you should find USB001 or something like that - something with USB in the name. If you don't see it - try steps 1-3 a few times.
Once you have seen the port, you can connect to the phone. The wiki has some instructions for getting to the USB prompt in mtty. Once you are there you want to issue the task 28. See if that helps.
Here is the link to the wiki - a link to mtty is there and some directions. Good luck.
Ok here what i obtained with mtty
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 14
Can't find OS in flash!!!
Storage format success
and now?
tetsuokaneda said:
Ok here what i obtained with mtty
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 14
Can't find OS in flash!!!
Storage format success
and now?
Click to expand...
Click to collapse
Well... let's see...
SD Card - No
PC - different BLs and RUUs - No
mtty - No
Manual BL mode - No
Almost stumped here... last resort: KITL + PLatform Builder
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
OR...
Flash an OS.nb file with mtty (READ THESE DIRECTIONS CAREFULLY)
Daaaamn i think will be a long night
I hope if is gonna work
Thanks todd_jg
i'll keep u posted
Well I was trying to upgrade mt niki to 6.1 but apparently I must have missed a step or did something I shouldt have and now I am stuck with the color bar screen. Can anything be done? I am running Vista.
tri-colour = Bootloader
The tri colour screen is the boot loader screen, when you updated, did the progress bar go allll the way to 100%?
If so, its in bootloader, try to flash another rom from you computer,
Also run through what you done to update - What rom also. Did you hard-spl, Uspl or anything like that?
It stopped at 15%. These are the directions I was following:
Originally Posted by Judge584
Follow these steps:
1. download the attached files (flash-uspl-niki.zip & sspl-1.16-nike)
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the uspl by running ROMUpdateUtility.exe from flash-uspl-niki
9. Now you can flash the latest rom update to have spl 1.22 and wm6.1.
ouch, Thats the only problem with sspl,
urmm.
How long did it stay at 15%?
As the device isn't CID unlocked you can only flash official roms...
Find an official rom, in the bootloader connect the USB and see if it will flash. It should do!
fingers crossed..
the only rom I can find for singtel in singapore is an updated one so I am trying that now so far so good, I am at 30%. So if this will get me going again can you offer a little advice or explination as to your last post, how do I go about loading a newer 6.1 rom on my device?
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Deejaynate said:
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Click to expand...
Click to collapse
well i was able to fix it by using the singtel rom. I want to use the Niki SuperCID unlocker but I have to install the " HardSPL 1.15 MFG " first - can you walk mw through this so I dont brick my touch again. do you have messenger?
yeah Windows live messenger, add me [email protected]
sorry to hijack your thread, but I encountered exactly the same thing. The screen is now stuck with 3 colour bands. I tried to flash it with an official rom, but the computer is not connecting with the phone, active sync does not recognise the device, any help!?
this is what I did:
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. running ROMUpdateUtility.exe from flash-uspl-niki
Sorry for the non prompt reply
I have been at work alot lately,
sorry for a non prompt reply.
Active sync wont connect to your phone, as its in bootloader mode.
At the tri-colour screen, does you computer beep when you connect it, or try to install drivers?
thanks for replying!
no beep from the computer, when connecting the usb to the phone, the phone changes from "serial" to "usb".
I tried reflashing with ROMUpdateUtility.exe from flash-uspl-niki, it will work, but says fail and will go into recovery mode. It will then complete the "recovery" action and go back to flashing new rom which won't work.......
The same ocurred with me!! Help me!
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
luismatos123 said:
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
Click to expand...
Click to collapse
You need to flash an original ROM from your service provider (phone company).
Hi,
My new Gene is bricked. I am trying with the Orefkov SPL updater. I am getting the Boot loader screen but I am stuck with MTTY. I am not getting the USB button. Please help
WHAT IS YOUR OS? IS IT WINDOWS XP OR VISTA/7?
IF YOU ARE USING WINDOWS VISTA/7 YOU NEED TO HAVE WINDOWS XP ACTIVESYNC DRIVER INSTALLED.
Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Here is the link to the Master of all masters Sumit's official thread for more info:
http://forum.xda-developers.com/showthread.php?t=472169
HI Schizo,
Thanks for the quick reply.
I have Win XP and I have ActiveSync installed. I have removed SD Card, Sim and did the same way you have explained. But still I am getting only COM1 and COM2 in the dropdown in MTTY.
Please help.
Anything specific to be done with ActiveSync?
go to computer> right click and select properties and go to device manager. Is there anything called pocketpc usb sync? If there is pocketpc usbsync or unknown device then Update it with the driver i have attached below. and one more thing keep on refreshing the page from time to time.
No Schizo. I dont have anything like that.
I have Windows Mobile-based Device#7 in Network Adapters. Is that a problem?
rexhyd said:
No Schizo. I dont have anything like that.
I have Windows Mobile-based Device#7 in Network Adapters. Is that a problem?
Click to expand...
Click to collapse
then upgrade that with pocktpc usb sync driver i have attached above and try again. Let me know if that worked.
Link:
http://forum.xda-developers.com/attachment.php?attachmentid=270636&d=1264088925
Sorry to ask but how to update it?
rexhyd said:
Sorry to ask but how to update it?
Click to expand...
Click to collapse
Unzip the files i have send you.
Go to device manager, right click on windows mobile and select update driver.
select browse my computer for driver.
select let me pick from device drivers and choose have disk.
go to the folder you have extracted the drivers and select pocketpc usb sync.
I am using windows seven but i believe steps is basically the same
I have right clicked on WceRndis and wceusbsh and selected Install. Will that do?
rexhyd said:
Sorry to ask but how to update it?
Click to expand...
Click to collapse
unzip that and then right click on inf files it shows install
then re plug device
rexhyd said:
I have right clicked on WceRndis and wceusbsh and selected Install. Will that do?
Click to expand...
Click to collapse
Now replug the device and start all the steps as posted before. Let me know if that works
Hi,
I have done it. Now I have a white screen and I am going to run RomUpdateUtility.exe program.
Thanks a lot
I am done now My SPL is 1.07.Oref. Thanks a lot guys. I was damn scared that I've lost my Gene. But You guys made it. Thanks once again.
Can you suggest which ROM will be best for my mobile?Please
congratulations, now update to the ROM of your choice. Glad to help. Had the same problem, woke up till 5 am in the morning trying to fix that. For new ROMS just browse the section. Plenty of ROMs for our new gene here. Enjoy
@schizo440 Good job mate
Great to hear that one more Gene was saved. Good job schizo440
@rexhyd : From now on, never flash any ROM that says its for Old Gene, and also those which say Stock Rom or Official ROM etc. For the second type of roms, ask in the forum first, whether they are safe or not. Good luck!
I have the same problem too.
Hey, I have the same problem. Im stuck at the tricolour screen showing SPL 1.10. Olip. Mtty doesn't sho usb option. Im on Windows 7 please help.
msrkanurag said:
Hey, I have the same problem. Im stuck at the tricolour screen showing SPL 1.10. Olip. Mtty doesn't sho usb option. Im on Windows 7 please help.
Click to expand...
Click to collapse
kill active sync process at taskmanager
really nice work schizo440......
Hey guys, as the title suggests....im having trouble
Trying to update my ROM.
Active sync works fine, up to the point I have to run the RUU and .nbh files, it just drops out and then i get the error 266 coming up.....asking me to check the cable etc.
Tried different USB ports and leads with no joy.
Strange one this, as I have updated my ROM before (around a year ago) with no trouble.
Help very much appreciated.
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
AndrewSh said:
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
Click to expand...
Click to collapse
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first?
Im following these instructions:
FIRST TIME FLASH
1. Remove SD (and remove Application Data and Program Files folders from it using SD card reader)
2. Remove HSPL with HSPL2_RUN.exe (flash SPL 1.66.0000 with HSPL2_RUN.exe)
3. PowerOff the phone
4. Boot to bootloader (VolDown+PowerOn) and when it shows "USB" flash stock ROM by running matching RUU_Leo_S_HTC_XXX_3.14.XXX_Radio_15.42.50.11U_2.15 .50.14_LEO_S_Ship.exe (get yours HERE or for Orange UK/FR HERE)
5. Hard Reset (when phone starts booting after step 4, remove the battery, insert it back press VolUp+VolDown and still holding both press PowerOn and follow the instructions)
6. Boot to homescreen.
7. Run SSPL_RUU.exe with Artemis v4X RUU_Signed_XXXX.nbh in the same folder - YOU HAVE TO BE ON HOME SCREEN, NOT BOOTLOADER (this took me 3 tries until succeded - yes - nerve wrecking, but works). If it doesn't work (hangs on black screen for more than 2min or stays at 0%) remove the battery and try again. If still doesn't work - try solutions in NOTE below.
8. Hard reset (instructions in step 5)
9. when on homescreen - softreset.
10. Insert SD
marlon32 said:
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first
Click to expand...
Click to collapse
You're going about things in a strange manner, using hspl.exe to set a stock spl and then using sspl to flash the rom? Pretty non standard, what are you aiming for? My guess is you are using outdated instructions from before Hspl4 was released to handle spl/hspl 3.03 (just a guess, of course)
Stabdard flashing a 3.14 rom would go as follows,
Phone into bootloader(forget actuvesync)
Run Hspl4.exe, choose 3.03.hspl
Back into bootloader,
Run the Artemis flash using custom ruu .
Done.
It won't show the current installed image because that is a simple registry entry and is only accessible when winmo is running, but when winmo is running the USB times out when the ruu reboots into bootloader,sim that's why we manually enter bootloader.
(I haven't checked in the Artemis thread as to if there's a reason why his rom wouldn't follow standard proceedures, but I did use exactly your process prior to Hspl4 release)
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
marlon32 said:
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
Click to expand...
Click to collapse
Thanks M8 Had the same problem and moved my usb cable to another port worked 100%
Hi,
I have received a Lenovo P 780 from Amazon after a long wait which was I guess a Chinese made phone. When I go to Google play I get only Chinese apps & also all system software from Lenovo are in Chinese language I cannot use whats app since it does not recognize my number and also it does detect my current city to show weather update.. I dont want to return this phone as it takes many days to return and get a new phone some one please assist me thanks in advance
Syed Moin said:
Hi,
I have received a Lenovo P 780 from Amazon after a long wait which was I guess a Chinese made phone. When I go to Google play I get only Chinese apps & also all system software from Lenovo are in Chinese language I cannot use whats app since it does not recognize my number and also it does detect my current city to show weather update.. I dont want to return this phone as it takes many days to return and get a new phone some one please assist me thanks in advance
Click to expand...
Click to collapse
Flash a ROW(rest of the world) ROM forom this forum. Your phone will be more understandable.
Sent from my Lenovo P780
stympy said:
Flash a ROW(rest of the world) ROM forom this forum. Your phone will be more understandable.
Sent from my Lenovo P780
Click to expand...
Click to collapse
Perfect can you please give me the steps that I should follow flash the phone with ROW apologies I'm new to these things..
Syed Moin said:
Perfect can you please give me the steps that I should follow flash the phone with ROW apologies I'm new to these things..
Click to expand...
Click to collapse
Ok here it is:
1. download in your computer the drivers
2. install drivers
3. restart your computer (just to be sure) (skip steps 1.2.3 iff you have allready installed drivers)
4. now... turn off your phone
5. plug your USB cable in your computer
6. plug your USB cable in your phone
7. new hardware detected should appear... and should install drivers automaticaly
8. after the drivers are installed unplug your cable from the phone and restart your computer (just to be sure)
9. after restart start flash tool
10. load scatter file from ROM directory(should be target_bin directory)
11. check DA,DL WITH CHECKSUM (NOT OPTIONAL)
12. press Firmware Upgrade button (NOT DOWNLOAD BUTTON)
13. now just now plug usb cable to your phone.
14. firmware flash should start.(some red and other color lines should appear)
15. iff the firmware is not starting remove the case of your phone and hold pressed the little red button for about 20 seconds then release. All this must be done with cable pluged in to your phone.
16. after flash is done a green circle should appear
17. disconect your phone and power on your phone
18. lenovo logo should appear. then you should be pacient because it will took some time before android boots for the first time.
19 Good luck.
stympy said:
Ok here it is:
1. download in your computer the drivers
2. install drivers
3. restart your computer (just to be sure) (skip steps 1.2.3 iff you have allready installed drivers)
4. now... turn off your phone
5. plug your USB cable in your computer
6. plug your USB cable in your phone
7. new hardware detected should appear... and should install drivers automaticaly
8. after the drivers are installed unplug your cable from the phone and restart your computer (just to be sure)
9. after restart start flash tool
10. load scatter file from ROM directory(should be target_bin directory)
11. check DA,DL WITH CHECKSUM (NOT OPTIONAL)
12. press Firmware Upgrade button (NOT DOWNLOAD BUTTON)
13. now just now plug usb cable to your phone.
14. firmware flash should start.(some red and other color lines should appear)
15. iff the firmware is not starting remove the case of your phone and hold pressed the little red button for about 20 seconds then release. All this must be done with cable pluged in to your phone.
16. after flash is done a green circle should appear
17. disconect your phone and power on your phone
18. lenovo logo should appear. then you should be pacient because it will took some time before android boots for the first time.
19 Good luck.
Click to expand...
Click to collapse
Hi,
Thank you so much for your help I tried doing that and step 15 does not complete. The phone is not getting detected I believe I installing MTK drivers but no luck when phone is connected to system in Device manager it show other devices and MTK driver with an ! mark but with in few seconds it goes off. I tried with many times but enabling all USB options from my phone. I will really appreciate your assistance thanks in advance.
Syed Moin said:
Hi,
Thank you so much for your help I tried doing that and step 15 does not complete. The phone is not getting detected I believe I installing MTK drivers but no luck when phone is connected to system in Device manager it show other devices and MTK driver with an ! mark but with in few seconds it goes off. I tried with many times but enabling all USB options from my phone. I will really appreciate your assistance thanks in advance.
Click to expand...
Click to collapse
I did it thanks to full updating the steps in details:victory:
Syed Moin said:
I did it thanks to full updating the steps in details:victory:
Click to expand...
Click to collapse
Sooo... it is working then..
Glad to help. :laugh: