Hi,
If I load HardSPL onto my Touch Dual, and I want to load a ROM - will I need to go through the SPL (soft/hard) process each time I want to try a ROM or if I load HardSPL once, that's all done and and I never need to do it again?
Thanks
yes,, HardSPL mean you never need to install another SPL again to keep flashing ROMs
Thanks for your help!
Related
i upgrade the ROM using this :
http://forum.xda-developers.com/showthread.php?t=283965
but I would like to downgrade it again to send for repair ...
i cannot flash it back to the original IMATE JAMIN rom , always stop at 95%.
Please help.
Just wait, suddently it continue.
Regards
"Just wait, suddently it continue."
No, it doesnt. Error msg comes out and forces you to it.
SPL can not be easily downgrade by flashing ROM in a G4.
Same problem
I have same similar problem.
I created new topic. I guess my topic more explanatory.
Lets go on here -> http://forum.xda-developers.com/showthread.php?t=331474
thanks..
NOW it is possible to downgrade SPL. Just flash HardSPL, after that you can DOWNGRADE SPL to any SPL you want!!!
nForce said:
NOW it is possible to downgrade SPL. Just flash HardSPL, after that you can DOWNGRADE SPL to any SPL you want!!!
Click to expand...
Click to collapse
When you first flashed HardSPL, which verson of the SPL was shown after reboot? That, what you had before, or the new one, of the HardSPL? I am asking, because I managed to keep the original O2 2.15 SPL and I really dont want to channge it (for repair reasons
After flashing the patched HardSPL I see 2.G4.4PDA (I have a G4 XDA Neo)! But the good news are that you now can flash all SPL versions you want, like the original 2.15 when it's inside of your ROM image and you can see it after rebooting!
How to use Hard SPL if a can't pass bootloader?
I tryed hard SPL, but after upgrading it back to 2.20.001., and I can't pass even to "Windows mobile" screen and it is frozen this position.
Any suggestions?
Thanks
I have updated my phone x01ht WM5 to custom WM6 firmware,
before installing the wm6, i had install the Hard_SPL-V7
i wanna know, if i want to flash again to other wm5 roms, how could i do?
because when i was trying to flash the wm5 dopod rom (it loads the loader) but stop flashing, error said USB connection failed..
any advise pls reply, thanks... i am very noob at this level
Follow THIS guide. You will be able to downgrade to WM5 again but it is not as simple as running the RUU.
(pof im adding the warning dont worry)
I have got the Hermes
ipl:1.01 spl:1.06
I have got the olipro's customruu
I have got the WM6 custel rom.
I only want to flash OS.
Steps:
1. put the customruu and nbh(only OS) in the folder
2. Flash the rom using SSPL option
Coz i dont want to change the SPL version, and i think flashing only OS will not brick my device.
Plz confirm this steps.
AND if ill flash the hardsplv7 will i be able to go back to spl 1.06and how? Please tell.
You can return to SPL 1.06 But i wouldnt recommend it, 1.06 is also known as 'the brick maker'. LOL
Seriously flash HardSPL v7 BEFORE you try ANYTHING else.
mrvanx i have read your guide, its awesome.
But if at all i need it for warranty reasons, can i get it back(IPL and SPL).
Thanks
YES, relax dude.
get flashing
Thanks really appreciate your help.
And to say another thing my company (imate) hasn't released any official ROM for my phone, i have checked the wiki there are roms similar from which i can extract the IPL and SPL and OS which i will need maybe in future.
And i have read that to change the IPL and SPL i need to make a .nbh containing only IPL and SPL and flash it using SSPL option of custom ruu, am I right on this.
Thanks
Yes the procedure is:
Split the .nbh (from an imate ROM...or ANY with IPL and SPL that you want)
into the component .nb files using duttys NBH tool (v1.1 i think).
Then rebuild a new .nbh using ONLY the IPL and SPL bits.
Then flash it with customRUU and (yes correct) select the force SSPL option.
Thank you SOOOOOOOOOOOOO much i think you have helped me alot.
Thanks again, for being so freindly.
Hi, I have been running Gollum's Prophet Touch VII on my M600 for ages now and fancied a change, I decided to dl varanusvincent's 'my diamind edition 2' and ran the g4 rom update that came with it, my m600 now is sat in the 3 colour bootloader screen with IPL 2.10.0001 and SPL 2.20.0001 and I cant get it to do anything, hard reset just puts it back to the bootloader screen, can ANYONE help me please or have I wrecked it by trying to install a new rom?
thanks
Mike
I've reset it again and it is now stuck on the 'qtek keep the world as one' screen with ipl and spl in the top left corners, the uodate programmes all say that is disconnected if i try and use them any ideas??
have you read how to upgrade it????
You haven't HARDSPL.
READ HERE to recovery your Prophet
I have already read over that entire post before I put this on, didnt want to look an idiot - no luck there then!
I have tried to use the hard spl folder upgrade and it still only gives me the 3 colours bootscreen after a hard reset, step 2 says use bootloader mode and flash pvtemp but I've looked everywhere for pvtemp and cant find it to dl
82mike said:
I have already read over that entire post before I put this on, didnt want to look an idiot - no luck there then!
I have tried to use the hard spl folder upgrade and it still only gives me the 3 colours bootscreen after a hard reset, step 2 says use bootloader mode and flash pvtemp but I've looked everywhere for pvtemp and cant find it to dl
Click to expand...
Click to collapse
with SPL information that you said. It said, that your Device is not HARDSPL already.
You have to succesfully HARDSPL your Device first.
And after that you wont face anyproblem again.
Download :
PDVIET Temp
Is your Device CID Lock?
So I dl PDAViet, flash with that, run HARDSPL with my new .nbf in that file and I should be ok? No idea about CID lock, thanks for helping
82mike said:
So I dl PDAViet, flash with that, run HARDSPL with my new .nbf in that file and I should be ok? No idea about CID lock, thanks for helping
Click to expand...
Click to collapse
So you have to Flash your ROM now with PDA Viet Temp first. This will bring your device to WM5 No Vendor.
You have to flash it through bootloader mode, since your device now stuck up.
After that , HARDSPL your Device.
Read better thread from animelover. Here
If your Device is a G3, SPL Information will be changed into 2.G3.4PDA or for a G4 is 2.G4.4PDA
And after your Device HARDSPL ready. Run the Upgrade tool from My ROM. So you wont stuck up again.
It should run.
thats great, im running pdaviet now, read the page about hardspl too so i'll install this, turn on my m600 and run hardspl g4 followed by your rom - thanks!!
82mike said:
thats great, im running pdaviet now, read the page about hardspl too so i'll install this, turn on my m600 and run hardspl g4 followed by your rom - thanks!!
Click to expand...
Click to collapse
I will update the ROM. A small registry failure. Not so important actually.
Just wait .
I am uploading this ROM now.
You can Hardspl your Device first anyway.
Done!!! Hard SPL'd now says 2.g4.4pda on booting! I'll hang on for the new rom to be uploaded, if i want to change roms again to I have to run pda viet or now that I have run hardspl can I just install over the top? sorry for all the q's and thanks for all your help
82mike said:
Done!!! Hard SPL'd now says 2.g4.4pda on booting! I'll hang on for the new rom to be uploaded, if i want to change roms again to I have to run pda viet or now that I have run hardspl can I just install over the top? sorry for all the q's and thanks for all your help
Click to expand...
Click to collapse
If you have HARDSPL.
And Your SPL Information changed into 2G4.4PDA .
No need to install PDAViet again.
Just run the installer from the cooker.
I am reading forums for few days now, i would like to install WM 6.5 on my touch dual, but i just dont get what i need to do. Is there some step by step tutorial.
Also, i am interested in android too, i tried one of them but it was poor. Is there some android for htc that actually works, and can be used normally?
Thank you
First off all, welcome.
If you just want to know how to start just read the first two stickies of this thread.
Regards,
Yes i read stickies but i dont get what i need to install, that is in what order, and which ROMs i need to use.
marijan_e said:
Yes i read stickies but i dont get what i need to install, that is in what order, and which ROMs i need to use.
Click to expand...
Click to collapse
Hmm, okay first we need to know what type off phone you have, you can find that under your battery, by me it's displayed Niki100.
Second one, which is important, is your device simlocked.
Regards,
I have it too Nikki100
No it is not sim locked
Okay, sorry for the late reply, but I was at my work, and also tonight I have to leave, if you don not have a simlock the only thing you have to do can be found here http://forum.xda-developers.com/showthread.php?t=631493 just read carefull and if you still don't know how it works just let me know and I will help you.
This is how i did it:
1. I just started at step 4, and copied the sspl 1.16 to my phone.
2. Turned the phone off.
3. Removed sim and sd-card
4. Turn on the phone and launched sspl 1.16
5. Connect on computer and usb appears.
6. Running hardspl 1.22
Thats all, I'm not sure if it is the right way but it worked for me.
Important:
Use at your own risk! I'm not responsible for any damage to your device.
Regards,
Ok so i run sspl 1.6 and i got the phone in bootloader mode, connected USB and nothing happens. What i should now try to put wm 6.5 ROM?
marijan_e said:
Ok so i run sspl 1.6 and i got the phone in bootloader mode, connected USB and nothing happens. What i should now try to put wm 6.5 ROM?
Click to expand...
Click to collapse
No, before you flash a rom, you have to flash Hardspl 1.22
Greetz,
You did not mentioned hardspl above?!?!
and what about that radio ROM do i have to flash that too.
I dont get you, so i run sspl, and i get bootloader, what now, do i flash hardspl while in that bootloader or?
marijan_e said:
You did not mentioned hardspl above?!?!
and what about that radio ROM do i have to flash that too.
I dont get you, so i run sspl, and i get bootloader, what now, do i flash hardspl while in that bootloader or?
Click to expand...
Click to collapse
Hi again, you only need to flash Hardspl 1.22 or 1.15 but they say that 1.22 is better, and yes you can do that in bootloader.
And why you have to do this is, because if you only use sspl you have to do that everytime you want to flash a rom with hardspl you only have to do this once and you can flash all the rom's (for the Niki) what you want, so this means if you can succesfull flash the hardspl 1.22 you are done with this and you can search for rom's you like
Hopefully I'll gave you enough information but if you want to ask something you can always ask, there is just a small thing with the radio but I explain that after you did the hardspl.
Greetz,