Help - iPAQ rw6828, XDA Atom ROM Development

Hi All
I tried to Downgrad my WM6 Touchy to Orginal WM5 rom, Then I cheng my Eboot from Bootloader with SD card & Now I cant get my divice in bootloader mod & when I try to Upgrad it in normal way my divice get restart, How can I fix this problem? pleas help me.

Why on earth would you do that!
Remove battery and press SR and Camera together, dont release!
Now insert the battery and then release SR and Camera.
if that doesnt work you need JTag method in Wiki and if that doesnt work send it to repair and if that doesnt work buy a new one.

My divice can turn on & normaly get in to the last wm I upgrated in to, but it cant get in bootloader mod & when I whant to upgrade it in loaded wm it sudenly get restart

Check the Wiki, need reinstall your bootloader

Related

after install 3.3.3 my atom bricked it stuck o2 screen pls help

hi
i updated my atom rom version to 3.3.3 three days ago.It installed completed i used this rom 3-4 hours then i was freeze and i try to reset it. it didnt respond so i decided to hard reset to my atom.I tried to hard reset now it says "device clean boot....." it stuck this screen then i try to reset the device then it stuck o2 screen it didnt pass to align screen. i cant use my atom for three days
Please help me......
remove the battery for a while.. then try hard reset / reflash
i try this method but it is same it doesnt work
did u try the instructions posted in aku 3.3.3.??..
"
For those of you who have downloaded and flashed using SD Card method who ended up in a brick! ITEX recovers his Atom by following procedure:
1. remove SD Card
2. remove battery
3. hold camera button and reset (stylus) button
4. replace battery while still holding the buttons
This will bring you back to bootloader mode. Just flash the above DSUU.
"
Does it have a chance to use wm6?
joolawan said:
Does it have a chance to use wm6?
Click to expand...
Click to collapse
it can barely use WM5 and anyway these chinese splash their advertising for WM6 all over the place in hope ppl will buy their rom, until I see it running in my device or get confirmation from someone reliable (such as Jiggs) I dont believe a word of it and besides the 3.3.3 rom is very fast and ten times better than any actual official release
yes i tried to that method too. it is same it still stuck on o2 screen. it doesnt pass to align screen..please help me
my problem didnt solve pls help me i cant use my atom..........
plsssssssss help meeee...........
plsssssssss help meeee...........
R U able to go to bootloader mode ?...
ironeagle said:
R U able to go to bootloader mode ?...
Click to expand...
Click to collapse
try to be on the bootloader and reflashed the ROM. try to search same cases in the forum. I think they solved the problem alike.
yes same to problem. i dont re enter bootloader again :S
did DSUU Recognize your ATOM ?..
Connect your ATOM to PC (using USB)
Run DSUU
Try to flash it..
i can enter bootloader mode and i can update rom but after this proccess it says "device clean boot......" and it freeze . it doesnt pass to align screen
plssss help meeeeeeee.
Which ROM you flashed?..
i flashed orginal atom rom i downloaded from seeo2.com
pls helpppp meeeee my atom is dead
are u using o2 atom exec or just atom?
cuyz i've got o2 atom exec..maybe i could flash it with o2 atom (yeah i cant flash anything with dsuu)
mine is o2 atom
did u amend any thing from the original ROM from seeo2? I mean you flash your atom with the original ROM...0426? without replacing the extended ROM...etc?

hp rw6828 wm6 (odd conditions) -> wm5

Hi guys,
Hi,
I'm a hp rw6828 user and is very much enthusiast to try out those wm6 roms made by those experts. However, i did a mistake while trying to flash.
I tried flashing with a rom from wantat but i forgotten to delete the EBOOT.nb0 before i clicked "upgrade". Then the program stopped at 6% for a long time and didnt move. I disconnect the cables and tried to turn the device on.
THe device can go into the wm6 and the start button can be use but the screen is "moved" to the right side and other function is not working.
After that, i did a hard reset and the the os seem to work like normal. However, when i tried to go into bootloader mode by pressing both "_" and soft reset. That didnt work. I tried another way by taking out the batt, leave it for a 10mins, press both "_" and soft reset, put in batt, release soft reset then "_" keys. That didn't work either.
But, just lately, i've tried taking out batt, holding the camera key and softreset, place back batt, release soft reset n camera button. This method works and i get what it seems to be an atom bootloader?
i get a black background with "MN1 Bootloader Mar 29 2006 13;52;14 copyright..... 1) debug module through UART 2) jump to DM Enter your selection.
I've searched the forums and found few ways to downgrade back to wm5 but those aren't the same conditions with what im facing. Can someone recommend how can i downgrade back to wm5 with the conditions that im facing? All you help is much appreciated. THank you.
You are lucky , at lease your device now become atom. My was totally cannot on power and just vibrate. Till I have to sent it back to HP SC and change the main board . Can you understand chinese , if yes than I have a solution you may try . Else you have to wait . I just download a program and doing some testing , the program is in chinese language .
Thx for you reply. I guess u can say that. I'm from msia but cant read chinese.
Is it possible to solve the problem by sending back to hp using warranty claim? I think i still have warranty left but its ending very soon. One more week i think.
elus said:
Thx for you reply. I guess u can say that. I'm from msia but cant read chinese.
Is it possible to solve the problem by sending back to hp using warranty claim? I think i still have warranty left but its ending very soon. One more week i think.
Click to expand...
Click to collapse
I don't think you still can claim under warranty unless you can make your phone total can't on and access to windows mobile. Last time I sent it back they charge me RM 385 to change the main board . I did talk to their technical personal , it seen like they don't know what is bootloader and flash it back to original rom . What they do was just change the main board with preloaded program .
Good luck
If you think that you can claim you warranty , than you just go a head . If not , may be you can access my thread "HP6828 WM6" , download any one of the rom that I post , follow the instruction accept downgrade bootloader . Enter your phone in bootloader mode . If you can start the process , than it will flash a new hp bootloader into your phone .
Against . Good luck
Cheers
I'm from malaysia also.
Ok. I'll try your method to restore the bootloader. Thx for the fast reply. I'll keep u update with the progress. Thx again.
elus said:
Ok. I'll try your method to restore the bootloader. Thx for the fast reply. I'll keep u update with the progress. Thx again.
Click to expand...
Click to collapse
You've flash ATOM Bootloader, there are many ways to restore to HP Bootloader ... don't worry !!!
nhocbanme said:
You've flash ATOM Bootloader, there are many ways to restore to HP Bootloader ... don't worry !!!
Click to expand...
Click to collapse
Can share the information how to restore back the HP original bootloader ? And the procedure . Thanks
First you must have HP bootloader file (Eboot.nb0) 1.01 or 1.05 are OK.
- Use DRUU to restore Bootloader : replace ATOM bootloader file with HP bootloader file
- Use miniSD to restore Bootloader : copy Eboot.nb0 to miniSD card, go to bootloader ... wait 1' it will auto hard reset.
After flash successfull remmember remove Eboot.nb0 from miniSD.
- Reflashing Bootloader using JTAG. (Use only when can't use two above menthods)
HP Bootloader 1.01 : http://rapidshare.com/files/82853862/HP_BL1.0.1.rar
HP Bootloader 1.05 : http://rapidshare.com/files/82853924/HP_BL1.0.5.rar
nhocbanme could you please specify which specfic DRUU should be use for your method? Thank you.
You should use DRUU of Chartreux, replace Eboot.nb0 and choose OS and Eboot
Remember copy a HP68xx ROM (diskimage_Ver.nb0) to C:\Windows\Temp with DRUU of Chartreux then start...
nhocbanme, you explanation seems vague to me. Probably cause im still new. Could you please give a clearer instructions? Thank you
elus said:
nhocbanme, you explanation seems vague to me. Probably cause im still new. Could you please give a clearer instructions? Thank you
Click to expand...
Click to collapse
-You must extract RUU in C:\Windows\Temp (no sub folder) then replace Eboot.nb0 with Hp bootloader 1.01/1.05
-Copy a diskimage_Ver.nb0 (any ROM WM6 for HP 68xx) to C:\Windows\Temp
-Run the DRUU program and choose OS and Eboot and start.
Goodluck !!!
It worked! Thx a lot nhocbanme and wantat. The methods restore the atom bootloader to hp bootloader. The DSUU by chartreux is a good tool.
Now, i would like to put this solution up into the wiki. How may i do so? Thank you.
hi, im william from M'sia. i like to know how you recover your previous installed AtomROm back to WM5.
can u provide some step to step detail
if possible upload some files can let me flash from memory card in the bootloader screen
ur reply are highly appreciated
thx ~~
williamSun said:
hi, im william from M'sia. i like to know how you recover your previous installed AtomROm back to WM5.
can u provide some step to step detail
if possible upload some files can let me flash from memory card in the bootloader screen
ur reply are highly appreciated
thx ~~
Click to expand...
Click to collapse
OK, please read my topic, I'll post a WM5 ROM flash via miniSD
help !!
im facing another problem again...
this time i changed the file extension EBOOT0502_MNT_01.01.03.nbf to EBOOT0502_MNT_01.01.03.nb0
(file from HP official WM5 SP34074, inside the installed folder )
and copy to memory card and put in 6828 then started to go bootloader screen
few minutes later my screen goes blank, and i tried with the revive methods
which is
-press the 2 softkey " - " and reset button
-put in the battery ,
-release reset, then release softkey
but didt work out!!!!no repsponse at all..tried many times..possible dead ad???
plz help me abit ..big troblem!
I dont think i can help u much here as im still new. From the looks of your problem, i guess u forgotten to cut the first 12bits (or something like that) of your bootloader when u use it to flash via mini sd. Maybe you can try the JTAG method mentioned in the atom wiki to restore your bootloader. Good luck.
Thanks guys!
The same exact thing happened to me yesterday..I was already about to sell my ipaq as a dead unit and i came upon this thread and after following the steps it did made ipaq alive again..
thank you very much guys,i hope you continue to help more people..
god bless and best of luck to you
more power xda-dev!

for all dead prophets

i saw lot of people have dead prophet problem, so i am here now to make a new thread to all this people and i hope to make it useful.
now we start
** FIRST : lets know names of prophet :
I mate Jamin, O2 XDA Neo, Qtek S200, Dopod 818 pro, Dopod 830, SPV M600, VPA Compact S.
** SECOND : we must know that before we trying to do any updating or change roms on my prophet i just need to do which called unlock for the prophet and then we after that been able to change any rom on my ( jamin ) and of course u need to be careful about Your device is it G4 or G3 ,
# and how we know its G4 Or G3 ?
# when u start Your Device u will see some numbers on left,
---------------------
IPL: 1.00.000
SPL: 2.20.000
GSM: 02.61.21
OS: 3.0.0.0
--------------------
and may be changed and that goes to the rom which You have, now we look for the last number on ( IPL and SPL ) , if we found it ( 0 ) it means You r G3 and if it ( 1 ) so You r G4 .
** THIRD : lets go to unlock , i will put programs in this thread it will help u in unlock.
-- Sync your device with computer and open the file u download it called HardSpl you will find two files one one foe G3 and G4 open your kind then you'll find a file called (( hardspl.bat )) okay, be sure your device is connected to computer then open the file and follow instruction and it will reset your device ,
now u ready to change rom.
TO BE CONTINUED
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
if any one can help please contact me.
hello
my device is jamin g4
it stopsat the boot loader and dono thing
can u help me please?
my e-mail is [email protected]
and suddenly after trying to update the spl been 1.01
please help me
can i fix it?
waiting for ur help
What is the IPL and SPL?
If the wiki where up, I'd suggest looking at that, but as it is I'll explain it now...
What ROM where you attempting to upgrade to?
To get the device back, I would say "Read the wiki" but it's down!!!
Download this ROM.
In ActiveSync, disable "connect through USB" (File->Connection Settings).
Put the device into bootloader (the three coloured screen) and connect it to the computer using the USB cable.
Run the file you downloaded earlier. This should then install a new ROM.
From there, just wait for it to finish.
Now, it should work!
From there, you could re install the Orange WM5 ROM, or try upgrading to WM6. Make sure you read all the relevant guides first!
thanks alot i did as u said but it stops at 80% or 88%
then show this message (error 326 invalid command )
please help me
i'm feeling bad
my mail is [email protected]
What brand the device? Has it been SIM unlocked?
hi again brothers, pal zerocool. first u must unlock ur device to be able to accept any rom after that and solve pproblems.
first flash this rom its offecial and it solve dead prophet problems.
then make hard spl by program open file called hardspl.bat.
make hard reset.
flash ur rom u want.
make hard reset again.
then enjoy.
i uploaded the hardspl program but i couldnt upload the rom its so big so u can look in ur mail u will find the solution.
u can extract file by any program for zip.and tell me the news
dont forget to look to ur mail. see all of u later
Dead prophet
Hi guys,
I have been using a sh... Nokia sine I broke my prophet G4 in december by upgrading the OS.
I had downgraded first to NVID and then I tried to upgrade and it fails at 95%.
Sine this day, my prophet seem totally dead, no light when plug on both charger or computer, windows do not recognize at all the device because it is turned off. And it really do not seem to charge...
I am living in China now and a guy told me I had to change the PB board...The ost is 100Euros, but I am almost sure I an find another solution...
The weird thing is I cannot charge it at all ( I mean no lights but does it charge a little?).
The guy tested my prophet with another battery and in that ase, it is stuck on the bootloader.
We tried several roms and it always fails at 95% and the error is 200 something, maybe 245 or 243, I do not remember sorry...
Is my phone hardware is dead? or it is just a software problem and I did not see the right guy?
Do I need to buy a new battery? I have read that sometimes the device is not able to recognize it even if it the offiial one and even if it is working on another device...
PLease help me I don't want to loose this phone that I've been using for almost 3 years...
Otherwise I will switch to an iphone but I am not sure to be as happy than I was with my prophet.
Xie Xie for your advice and answers.
Guilh1
Can it enter bootloader at all?
If yes, what are the IPL and SPL?
If not, it will be a hardware problem (may just be connectors to the battery but may be something more).
the only way of recovery is using jtag
but 1st we must discover the location of jtag pins on motherboard
I just do not know because with my actual battery, anything is possible....
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
I may be right about the battery onnectors though, but the problems seem to be from the phone connectors or the battery it self???
Thank you anyway for your very quick reply
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
Click to expand...
Click to collapse
If it can enter bootloader, it is almost certainly your battery at fault!
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/B] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
Click to expand...
Click to collapse
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/b] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Click to expand...
Click to collapse
Please look at this if you want more help, post here...
thanks alot dear samuraititio
but i can't flash it
it writes (no vender id)
help me please i tried another tool with the same nbf file it stops at 80%
and it automatically enter the boot loader
and i can't do ant thing
its information
jamin/g4
ipl 2.13.0001
spl 1.01
i think my problem is in the spl coz it was 2.13.0001
and now it's 1.01
how can i fix it please i still starter in this way so i'm trying;
help soon please
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
l3v5y said:
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
Please look at this if you want more help, post here...
Click to expand...
Click to collapse
hello pal i3v5y
i have the same problem
idid what u said the flashing stops at 80%
i need ur help please
i'm online at the moment and u too help me soon if u can please
my e-mail is [email protected]
waiting for u i don't have any other device to use and i need it
l3v5y said:
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
Click to expand...
Click to collapse
now i flashed the official rom of jamin but it stopped at 80%

Need WM6.1 Original for HP IPAQ rw6815

Hello did somebody know from where i can download original WM 6 or 6.1 ROM for HP IPAQrw6815-not modified?
thanks
Teodor
[email protected]
hp doesn't come out with WM6 or WM6.1 for ipaq 6815.... there's only custom roms which are modified to work with ipaq 6815... you can choose from a variety of them in here.... have fun!...
thaks for this
Help with My ipaq 6815
Nhocbanme hi,
i've read thru many of the replies in this forum. i'm a newbie and don't knw much abt roms. i tried upgrading or if u call it flashing my ipaq via PC and later SD. the PC flash did not work. i had to wait almost the whole day becos it said it was reading configuration from the phone. i later tried the flash via a transcend 1GB miniSD and till today the phone has gone off. i tried to power it on even with th e battery fully charged. my sis has the same phone i tried swapping batteries but it still didn't come on. i really need to upgrade to windows mobile 6.1 i formerly had WM 5.0, today itried again and it still stays on the boot screen.(white background with the HP logo and the Pbl 1.05 at the botton of the screen .
please i need help ASAP.
Downlgrade your bootloader to 1.01
Hi,
You have to downgrade your bootloader from 1.05 to 1.01. Find in the following the instructions how to do it. I did it and it's working.
Be careful when you do downgrade, because you can end up without phone
Quote:
How to flash from PC with Windows XP (It is ok to run it in vmware)
Thanks Knave and rcperez for posting their detailed experience so I can write this section. Also thanks jimmyspa for improving the addheader's performance greatly.
1. Check your Boat loader version
(do a soft reset, and check the value printed at the bottom during the HP logo screen)
2. If you noticed that the last line states BL 1.00.05, it means you have boat loader 1.05 installed. You will need to download and flash your phone back to 1.01 via ftp://ftp.hp.com/pub/softpaq/sp34001-34500/sp34053.exe (VERY DANGEROUS, FLASHING VIA SD IS MUCH SAFER!)
3. After successfully downgraded your phone's boatloader, or your version was already v1.01, you can proceed to flash your phone to the rom.
With the check done, proceed with the required files.
1. Go to download section to download the rom file. -- The rom that you downloaded, e.g (diskimg.nbo)
2. Download the file pcupdate.zip attached in this thread and unzip the contents to the same folder you used in step 1.
3. Download the latest Rom file and extract to the same folder
4. Run BuffereAddHeader.bat. It will take seconds to generate a diskimage_Ver.nb0. (You should have Java Runtime > 1.50 installed, http://www.java.com/en/download/manual.jsp)
5. Move your phone to boatloader mode ( press the two - keys, follow by a poke at the soft reset hole with your stylus )
6. Connect the phone to the PC
7. Execute the Device Utility Update program and wait till it verifies the state. Click on Update Item "All" use cursor keys to change it to "OS ONLY" then hit next **** SELECT "OS ONLY", if you cant change it to "OS ONLY" DONT PROCEED!!! It should detect your device as Model 0 etc.
8. Press Next to begin flashing.
9. Once completed, the phone will reset by itself. Wait for a while for it to startup.
REMEMBER SELECT OS ONLY BY PRESSING DOWN IN THE SELECTION BOX
Here are the notes & files provided by hochengsoon with README for flashing via Windows XP
PC flashing using BL1.0.1 must be done from C:\Windows\Temp, so why not start everthing from this folder ie PCUpdate + ROM + missing file(s).
PCUpdate1.rar - http://www.mediafire.com/file/k5jumzzg1mm/PCUpdate1.rar
How to downgrade to WM5 using PC
1. download wm5 rom from http://h20000.www2.hp.com/bizsupport...pappid=NextGen
2. run it and after entering the updating screen cancel it.
3. replace the hpRUU.exe in c:\IPAQ(default install) with the attached file hpRUU.exe in archive hpRUU.zip
4. Connect device to PC, then press and hold two "-" button and reset.
5. Run hpRUU.exe and do a normal update.
Note: you may delete eboot*.nbf to prevent bricking the device.
bootloader missing
well i m using HP rw 6815, n last night i had flashed a 6.5 rom , later i was unsatisfied with tat rom,
so i went 2 change it, n during tat process, my phone turned off, n now it doesnt switch on, 1ce i managed 2 go 2 boot screen thr i cud see hp logo n bl-0.0.0 can ne1 help me out with it, how do i put bootloader in phone.. neither my pc detects the phone... help appriciated
HI i had same problem on hp rw6815
No bootloade aparantly but bootloader hp logo loaded but insted o o.0.o i had a ff.ff.ff bootloader. i dunno what that meant. i inserted a eboot.nb0 on sd reseted in bl (v1.0.5 from this forum).... bootloader updated oki.. but my phone transformed in a hp rw6828, and i can install 6828 rom working and bootin fine in rw6815, the rw6815 rom install via sd but restarts on boot screenn .. this appeard when i tried a downgrade from wm6.5 to wm5 when i try to upgrade via hpruu it looks tat i have a no language hpipaq model.. My model info is "€ R 0 6 0 8 2 2 N _ M N 1 A R C _ R S 0 0 0 5 2" i dont know how to interpret this file sysyinfo.txt with that data. my question is how can i downgrade to wm5 and original bl of hp rw6815? i have all files in nbf form. The onli soluton to the problem if ur phone restarts after rom upgrade downgrade on witn wm 6.5 an 1.01 bl is the atrached rom.. workin 6815-camera-patched-R3.zip is the only rom... located here http://forum.xda-developers.com/showthread.php?t=360664 second post under orher roms
6815 camera patch may work version r2: http://www.mediafire.com/?lihy0vcvnxd
6815 camera patched version R3: http://www.mediafire.com/?2mjhtgjox0x
This roms get ur phone alive after this bug... or the restar bug... they work with both 1.0.1 bl and 1.0.5 bl more stable with 1.0.1... and i thing the developer of the rom did not change the indentifier of the rw6828 rof for 6815... i think it;s hybrid rom between... it works.
Plese help me to downgrade to original state... hp rw6815 bl 1.0.5 rom wm5. or help me solve the hpruu problem... not patched for model and lang beacouse it says the same incopatible thing.. the picture is the same result in patched and original ruu.. .
me too
i got that same problem i dont know wahta to do help guys
bootloader missing after Upgrading to wm 6.5
Hi Dear, i had the same problem but the solution is so funny.
1. Remove Battery from your mobile.
2. Remove SIM card too.
3. Wait around 5 min. & put them back again.
4. Everything should be OK
I hope Problem solve like me , But realy i don't know why ??? .
Best regards, Jalal
I tried to flash the 6815 is here and I have put my diskimg.nb0 on 2gb memory card. Press the 2 buttons with the "-" and give it to reset with a stick ... I get into the bootloader and returns to the screen while windows. It might be because the bootloader has the pda is 1.0.5??
The problem is that trying to change the bootloader 1.0.1 is here and not working because my pda is Spanish.
How can I reduce it?
Dear SHKUMBIN,
I am very grateful for the clear and beautiful explanation, which indicates that a great effort and considerable experience and also " NHOCBANME " and " ARIEY " for the great job they do to bring those custom rom's.
Accept my greetings.
karamzak

Very big problem with a g4 mda vario plz need help

Hello All
my work has 100 mda vario's
but they all had windows mobile 5.1 on it
so i say to my boss i can flash it to windows mobile 6 with htc touchflo
he liked it so he let me do it
but it goes wrong
the mda vario does nothing anymore
just a bootloader cames up with : red green,blue,white
saying :
ipl 2.21.0001
spl 2.21.001
my idea is to get a working rom on a mini sd card and flash it from the sd card
but how to let the sd card starts load and let it flash,
not one button works in the bootloader
i have tried a lot of tricks i also have one time get restore to factory defaults.
but wont work, it says format completed, so no error's
thats good i think
but i really need to fix it.
otherwise my boss wont be happy
also active sync wont work anymore , the pc wont see the phone all .exe updates ultilty gives me errors that they dont get response from the phone
that comes because it only stays in the bootloader and the bootloaders has left under a usb sign, there stood usb
can this be fixed?
any help plz
Regards
R.G
hi there... 2 bad is the boss phone!!!
hi there... 2 bad is the boss phone!!!
first of all, try a hard reset, then plug once again the phone to PC
dont worry, activesync wont recognize phone at all (is just usb connection)
tell me if hard reset worked, and ill keep in touch
i kpnw there is a tool that would help you to fix the phone.... first try the hard reset!
Good luck
I got the same problem, the hard reset works, but the problem is there yet.
Ich hab das gleiche Problem, der Hard reset funktioniert, das Problem besteht jedoch weiterhin
Hello All
Thanks for u responses i like that
okay hard reset works
but nothing has changed by that
hard reset is the question with restore to factory defaults?
and than i get a screen with format complete.
Regards
R.G
hello All
i fixed it
i know get a green screen with ipl,spl, os
but everything is terrible slow
really slow i mean when i press start it takes a minute to show up
why is this?
plz help
i fixed it with abort all processes in task manager and use wizard love rom.
this is the only possible way i think
regards
R.G
R.G
You know what you did,whats wrong with the phone,you flashed a wm6 rom to a CID locked device.A CID locked phone cannot be upgraded to wm6,you must have a CID unlocked device for upgrading to wm6.
Now,as its a G4 device,it cannot be CID unlocked,but,however,it can be upgraded to wm6 through either SoftSPL or HardSPL method.
Now first recover back to its default status by downloading official stock rom and flash it,after it starts to work normal,then follow the SoftSPL or HardSPL method,only then it'll upgrade.

Categories

Resources