Related
Dear All master,
I need help on my o2 Atom, when I upgrade it to latest version, it stop on stage 5: Burn in Radio Rom, 0%. Nothing happen even I had to wait for 1 hour.
I upgrade it with original atom rom from o2 site : 'Xda-Atom-ENG-20060426-MOT0822.exe'
The device stay in "O2" screen. this device can switch to diagnostic mode.
what should I do?
Note I repeated loading rom but Ietunai problem in Flash
Probably the Radio Hardware broken.... try to install without the Radio ROM.
sliders7 said:
Probably the Radio Hardware broken.... try to install without the Radio ROM.
Click to expand...
Click to collapse
from wher i can find that rom ?
or can u upload it ? for me plzzzz
http://pdaviet.net/showthread.php?t=17158
you can find how to flash rom without bootloader, extended rom , radio.
read my first post
medkid said:
http://pdaviet.net/showthread.php?t=17158
you can find how to flash rom without bootloader, extended rom , radio.
read my first post
Click to expand...
Click to collapse
but my phone is dead and it fail when i try to unpgrade it and it gave this eorr ===
!!!Please use DSUU in OS mode and syno with PC first !!!
usb transfer fail.
what shoud i do now plzz help me i dont know how to get it in DSUU mode its gose on boot loader but cant get it in to DUSS MODE
my Xda Atom Exec o2
waseemraj said:
but my phone is dead and it fail when i try to unpgrade it and it gave this eorr ===
!!!Please use DSUU in OS mode and syno with PC first !!!
usb transfer fail.
what shoud i do now plzz help me i dont know how to get it in DSUU mode its gose on boot loader but cant get it in to DUSS MODE
my Xda Atom Exec o2
Click to expand...
Click to collapse
u can't update using DSUU from activesync anymore. since u got broken ROM.
u must use Bootloader by pressing:
-power + camera + reset
-plug the USB
-start the update using DSUU.
sliders7 said:
u can't update using DSUU from activesync anymore. since u got broken ROM.
u must use Bootloader by pressing:
-power + camera + reset
-plug the USB
-start the update using DSUU.
Click to expand...
Click to collapse
i just do as u say but the but it fail gives the eorr as i told in my last post
and plzz tell me is i just have to get it in bootmode and conact it with usb and start updating
what is DSUU?? is this the file Xda-Atom-Exec-ENG-20060721-MOT0822 ? or what ?
Easy fix, check post #12 http://forum.xda-developers.com/showthread.php?t=319945&page=2&highlight=EBOOT
more than likely you will need a 256 or 512MB SD Card, the method discussed here (in most cases) will not work with higher capacity cards. Check the Atom Wiki too.
homer285 said:
Easy fix, check post #12 http://forum.xda-developers.com/showthread.php?t=319945&page=2&highlight=EBOOT
more than likely you will need a 256 or 512MB SD Card, the method discussed here (in most cases) will not work with higher capacity cards. Check the Atom Wiki too.
Click to expand...
Click to collapse
i tryied that too but still same postion.....
what shoud i do now plzzz help me i tell u again what it look like
====================================================
USB connected,waiting for download ..............
!!!Please use DSUU in OS mode and syc with PC first!!!
Usb Transfer fail
some one plzzzz help me ? for my atom exec
waseemraj said:
some one plzzzz help me ? for my atom exec
Click to expand...
Click to collapse
well...
after u see bootloader screen and waiting to download.
it should be ok to connect to USB and PC will recognize it for sure!
if doesn't... u should try different computer. not yours. just borrow somebody else computer... see the outcomes? just in case u got error/corrupted activesync.
if still not working... u must using SD card upgrade.
Use any ROM.. use WM5 Official ROM.
Extract the ROM.
put: diskimage_Ver.nb0 to the Blank SD card (use 512MB or 1GB)
and activate the bootloader again.
If your device are normal.. it should looking for SD card and start installing the ROM. If your device badly damage.. it will NOT run both method.
i don't know this is your hardware or Software are damage.
Maybe u should send it to the repair... hopefully u still got the warranty.
If Hardware is the problem, usually they replace the motherboard.
because no way to fix NAND memory module.
just keep trying... don't try one time only...
Good Luck & Pray!
sliders7 said:
well...
after u see bootloader screen and waiting to download.
it should be ok to connect to USB and PC will recognize it for sure!
if doesn't... u should try different computer. not yours. just borrow somebody else computer... see the outcomes? just in case u got error/corrupted activesync.
if still not working... u must using SD card upgrade.
Use any ROM.. use WM5 Official ROM.
Extract the ROM.
put: diskimage_Ver.nb0 to the Blank SD card (use 512MB or 1GB)
and activate the bootloader again.
If your device are normal.. it should looking for SD card and start installing the ROM. If your device badly damage.. it will NOT run both method.
i don't know this is your hardware or Software are damage.
Maybe u should send it to the repair... hopefully u still got the warranty.
If Hardware is the problem, usually they replace the motherboard.
because no way to fix NAND memory module.
just keep trying... don't try one time only...
Good Luck & Pray!
Click to expand...
Click to collapse
The above information will likely do more harm than good!
waseemraj said:
i tryied that too but still same postion.....
what shoud i do now plzzz help me i tell u again what it look like
====================================================
USB connected,waiting for download ..............
!!!Please use DSUU in OS mode and syc with PC first!!!
Usb Transfer fail
Click to expand...
Click to collapse
Bro I have recovered from this 20+ times, if its not working (and you can enter bootloader mode) then you're doing something incorrectly, either that or your memcard is incompatible, remember in most cases 256 or 512MB are the only working sizes! So place that EBOOT.nbo into and "empty" SDCard with your PC, enter the bootloader then stick the card in.... It wont take long, once you the screen goes black pull out the SDcard and then enter bootloader, plugin your USB and execute official O2 rom AKU2.2
The flash may not finish completely freezing in the Extended rom update, dont panic! unplug, softreset then flash in DSUU mode...easy as! works every time!
homer285 said:
Bro I have recovered from this 20+ times, if its not working (and you can enter bootloader mode) then you're doing something incorrectly, either that or your memcard is incompatible, remember in most cases 256 or 512MB are the only working sizes! So place that EBOOT.nbo into and "empty" SDCard with your PC, enter the bootloader then stick the card in.... It wont take long, once you the screen goes black pull out the SDcard and then enter bootloader, plugin your USB and execute official O2 rom AKU2.2
The flash may not finish completely freezing in the Extended rom update, dont panic! unplug, softreset then flash in DSUU mode...easy as! works every time!
Click to expand...
Click to collapse
Confirm!!!
I have done this also even using 1 GB memcard, my memcard is NCP mini SD.
I don't know it was lucky or it does work for 1 GB memcard. Even with non empty one.
But becareful, maybe I am just lucky, perhaps you should use 256 MB or 512 MB only.
homer285 said:
The above information will likely do more harm than good!
Click to expand...
Click to collapse
hei... he is desperately need help.
We all want to help him, thats all i can offer.
If you have different method.. thats a good news for him.
everybody here try to help him.. contribute something to help him.
so no more harm to his already broken device.
think the brighter side!
cheers
first i tride to but another rom in my pocket (htc touch dual) then i follow the steps put the screen kept in color screen (bootloder) >>>
i try to format but it steel there and write in it :
NIKI100
SPL-1.17.0000
CPLD-4
please help me
you cold try hard reset:
power off
hold call+call disconnect buttons together, then while holding these press power on button.
but, i'd wait until someone whose tried flashing roms confirms this will reset back to original touch dual rom, as i havent tried flashing as of yet
Download MTTY and use Command "boot" if it doesnt work ... please tell us what you have done???
Why nobody cant use the search function and why on earth it is impossible to tell, what was the last thing you have try to get this error!!!
If you have get your OS back ... please dump your SPL and share it with me, for future development!
badaas said:
you cold try hard reset:
power off
hold call+call disconnect buttons together, then while holding these press power on button.
but, i'd wait until someone whose tried flashing roms confirms this will reset back to original touch dual rom, as i havent tried flashing as of yet
Click to expand...
Click to collapse
thamks but it not works
NetrunnerAT said:
Download MTTY and use Command "boot" if it doesnt work ... please tell us what you have done???
Why nobody cant use the search function and why on earth it is impossible to tell, what was the last thing you have try to get this error!!!
If you have get your OS back ... please dump your SPL and share it with me, for future development!
Click to expand...
Click to collapse
from where can i Download MTTY ??
here you are..
sackbauer said:
here you are..
Click to expand...
Click to collapse
thank you alot
but how to use it ????
i'm still waiting
hä? what do you mean - you want this tool but do not know how to use it ! for what reason do you want this tool then ?
disable active sync
connect phone trough usb and start program.
any more help -> try search function
i am off
sackbauer said:
hä? what do you mean - you want this tool but do not know how to use it ! for what reason do you want this tool then ?
disable active sync
connect phone trough usb and start program.
any more help -> try search function
i am off
Click to expand...
Click to collapse
thank you for helping
dont be engry from me becose i dont know how to use the program ..
i just want to end my proplem
NetrunnerAT said:
Download MTTY and use Command "boot" if it doesnt work ...
Click to expand...
Click to collapse
Make sure that right after you ENTER on the "boot" command you DISCONNECT the USB cable. That worked for me. Now I'm sporting the WWE ASIA rom.
aiondennis9000 said:
Make sure that right after you ENTER on the "boot" command you DISCONNECT the USB cable. That worked for me. Now I'm sporting the WWE ASIA rom.
Click to expand...
Click to collapse
thank you
all works but whene i update to wwe asia rom its stoped in 1% then my phone come in black screen then return back color screen bootlodere
do you know whats the problem ??
falojjah said:
thank you
all works but whene i update to wwe asia rom its stoped in 1% then my phone come in black screen then return back color screen bootlodere
do you know whats the problem ??
Click to expand...
Click to collapse
Basicly I did the following:
After recovering from the tri-color screen I did it according my own procedure to make sure it works:
1.) I placed the sspl-1.16-nike.exe on the Niki
2.) disconnect the USB
3.) Then renamed the hardspl-1.15mfg-nike.nbh to uspl-1.16-nike.nbh in the flash-uspl-niki folder
4.) run the sspl-1.16-nike.exe on the device
5.) connect the USB cable to device and desktop/laptop
6.) wait for it to say USB on the Niki
7.) flash the renamed uspl-1.16-nike.nbh with ROMUpdateUtility.exe from flash-uspl-niki
8.) ran the sspl-1.16-nike.exe on the Niki again
8.) and install the WWE ASIA rom afterwards.
Problem solved
ps: I stated 40 some hours of battery time compaired to the original T-mobile rom. Currently I am exceeding the 48hrs and have mad amount of batterylife to spare. Usage was 7% per 8,5hrs. You do the math. I am going to make 4 days with usage and 5 days would be without usage. I'll keep you posted.
falojjah said:
thank you
all works but whene i update to wwe asia rom its stoped in 1% then my phone come in black screen then return back color screen bootlodere
do you know whats the problem ??
Click to expand...
Click to collapse
please .... please!!
Read the hole Threads befor you do any thing!!!!!
Same Hacks are very complicate. If you dont wana read ... buy a normal Mobile Phone. I thing you dont want buy a 700us$ Phone and kick it one week later.
aiondennis9000 said:
Basicly I did the following:
After recovering from the tri-color screen I did it according my own procedure to make sure it works:
1.) I placed the sspl-1.16-nike.exe on the Niki
2.) disconnect the USB
3.) Then renamed the hardspl-1.15mfg-nike.nbh to uspl-1.16-nike.nbh in the flash-uspl-niki folder
4.) run the sspl-1.16-nike.exe on the device
5.) connect the USB cable to device and desktop/laptop
6.) wait for it to say USB on the Niki
7.) flash the renamed uspl-1.16-nike.nbh with ROMUpdateUtility.exe from flash-uspl-niki
8.) ran the sspl-1.16-nike.exe on the Niki again
8.) and install the WWE ASIA rom afterwards.
Problem solved
ps: I stated 40 some hours of battery time compaired to the original T-mobile rom. Currently I am exceeding the 48hrs and have mad amount of batterylife to spare. Usage was 7% per 8,5hrs. You do the math. I am going to make 4 days with usage and 5 days would be without usage. I'll keep you posted.
Click to expand...
Click to collapse
it works thanks alote
i dont beleve it
NetrunnerAT said:
please .... please!!
Read the hole Threads befor you do any thing!!!!!
Same Hacks are very complicate. If you dont wana read ... buy a normal Mobile Phone. I thing you dont want buy a 700us$ Phone and kick it one week later.
Click to expand...
Click to collapse
thank you for what you do for me
NetrunnerAT said:
please .... please!!
Read the hole Threads befor you do any thing!!!!!
Same Hacks are very complicate. If you dont wana read ... buy a normal Mobile Phone. I thing you dont want buy a 700us$ Phone and kick it one week later.
Click to expand...
Click to collapse
I read the whole thread before and I ended up as falojjah with a tri-color screen. My alternate procedure worked for me and now works for falojjah and all you can say is the above? pffff
falojjah said:
it works thanks alote
i dont beleve it
Click to expand...
Click to collapse
You're welcome buddy
Ooh and you might want to run TouchDual_FLO abnormal.exe just to be sure. It's on the HTC e-club download section.
aiondennis9000 said:
You're welcome buddy
Ooh and you might want to run TouchDual_FLO abnormal.exe just to be sure. It's on the HTC e-club download section.
Click to expand...
Click to collapse
Not all Roms need it!
Install it only, if you have a TouchFLO Problem. The most Roms have includ it!
NetrunnerAT said:
Not all Roms need it!
Install it only, if you have a TouchFLO Problem. The most Roms have includ it!
Click to expand...
Click to collapse
And to this downplay I say that it does make sense to install it because it clearly made Touchflo respond smoother and quicker on the WWE Asia rom. pfff
Guys i tried to upgrade my imate jasmin, to wm6 the problem was that it started to upgrade the rom but the process was interrupted, when i tried to turn it on again it does not pass the initial blue screen that gives the info of the rom. The active sync does not work because the PDA does not connect to the computer and doesn´t pass from the initial blue screen.
Is there anything you can do, or the PDA is to the trash.
Hope you can help thanks. http://forum.xda-developers.com/images/smilies/confused.gif
Which Rom
Which ROM you use?
well i used the rom that is the upgrade for wm6 that is on the portal, the one that is for prophet, but the upgrade didn´t reach the end and now the pda does not pass from the blue initial screen and it isn´t possible to achive any type of conection to the PC i don´t know what to do...
deltav13 said:
well i used the rom that is the upgrade for wm6 that is on the portal, the one that is for prophet, but the upgrade didn´t reach the end and now the pda does not pass from the blue initial screen and it isn´t possible to achive any type of conection to the PC i don´t know what to do...
Click to expand...
Click to collapse
Bro. Try the methode found in the sticky:
FLASHING TOOL For all nk.nbf (WM6.1), 3 color bootup? SOLUTIONS ... in
http://forum.xda-developers.com/showthread.php?t=353547
In ur case, although the connection seem disabled, we could still force the activesync to work for flashing. Just right click the activesync icon in lower right corner of ur pc, choose connection, force it to search the usb. retry once or twice if u r not sure, then try to reflash the rom while the activesync seem still searching for devices. If it won't start, then the better way is to follow the step from Dioxda2 above. If it started halfway as before mean u have to re download the rom with its all suitable methode such as Hardspl, jumpSpl etc.
This work on my Dopod 818pro while stucked on 3 colour bootloader screen. Hope it will work on ur case too. Good luck.
thanks bro, hope it works, i will tell you later if the pda is back online
deltav13 said:
thanks bro, hope it works, i will tell you later if the pda is back online
Click to expand...
Click to collapse
Hi again, bro. Any progress? Good luck.
ITS A HTC HD2 NOT THE ORIGINAL
Ok I am a really big noob and need some help. I Flashed My rom using Miri_HD2_WM65_21893_Sense25_V6.0.rar, I extracted in and it completed 100% and loaded up perfectly to home screen. I didnt have my sim card in or Sd card so I took battery out and put my sim card and sd card back in. When I turned it back on it was stuck on the HTC screen. Just the Green HTC writing and white screen and thats it. I have read some forums that have had the same problem but i just dont get it. they say get into bootloader ( which i can do) and then flash with radio or something... I am uncertain how to do this. When I downloaded one of them Customruu or whatever it is and open it it says I have to connect through active sync which i cant do because I cant get my device to turn On... I really need some help but it needs to be explain to me like explaining to a handicap person.
thanks
Put into bootloader, not necessary to connect to Activesync as you can't in bootloader mode. Flash the radio the same way as you flashed the rom. put the radio.nbh file in a folder, rename it to RUU_Signed.nbh and copy a CustomRUU.exe in and flash.
You'll find radios and steps here.
jaza20032000 said:
Ok I am a really big noob and need some help. I Flashed My rom using Miri_HD2_WM65_21893_Sense25_V6.0.rar, I extracted in and it completed 100% and loaded up perfectly to home screen. I didnt have my sim card in or Sd card so I took battery out and put my sim card and sd card back in. When I turned it back on it was stuck on the HTC screen. Just the Green HTC writing and white screen and thats it. I have read some forums that have had the same problem but i just dont get it. they say get into bootloader ( which i can do) and then flash with radio or something... I am uncertain how to do this. When I downloaded one of them Customruu or whatever it is and open it it says I have to connect through active sync which i cant do because I cant get my device to turn On... I really need some help but it needs to be explain to me like explaining to a handicap person.
thanks
Click to expand...
Click to collapse
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
where do I get the Customruu.exe from? What do you mean flash the radio same as the rom? how can i do that if i cant get connect to active sync? So does that mean I have to download Miri_HD2_WM65_21893_Sense25_V6.0.rar again? which radio file do I choose? I am so confused. Dont get annoyed its just i dont understand all this...
do NOT do it via SD card - flash the radio using activesync as mentioned in first reply. SD card is dodgy as hell and the quickest way to brick your phone for good
You can get CustomRRU from any ROM file - use the one from Miri's ROM
might've been worth reading the n00b flashing thread first as well as well as the first thread of Miri's ROM as all the info is on there...
how come you can't use activesync? what version of Windows you using?
in future i suggest you read the relevent threads and make sure you can flash a stock ROM before jumping into cooked ROMs...don't wanna brick an expensive phone do you?!?!
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
I can't use the SD card because I dont have the adapter thing to be able to hook it up to my comp only way i could access it was through my phone in hard drive mode. So basically i cant put any files on it without using the phone... Any other suggestions?
futher info from Miri's ROM thread...
"You MUST use radio 2.07.50.27 or 2.08.50.08"
read this thread...
http://forum.xda-developers.com/showthread.php?t=609477
all will become clear - or it should do!!
EddyOS said:
do NOT do it via SD card - flash the radio using activesync as mentioned in first reply. SD card is dodgy as hell and the quickest way to brick your phone for good
You can get CustomRRU from any ROM file - use the one from Miri's ROM
might've been worth reading the n00b flashing thread first as well as well as the first thread of Miri's ROM as all the info is on there...
how come you can't use activesync? what version of Windows you using?
in future i suggest you read the relevent threads and make sure you can flash a stock ROM before jumping into cooked ROMs...don't wanna brick an expensive phone do you?!?!
Click to expand...
Click to collapse
If you read my post I cannot get into the home screen... My Phone is stuck on the HTC boot up screen therefore making it impossible to use activesync... I did read all the Noob and Miri **** and it worked. I got to the new rom, but when i took the battery out and put sim card and sd card back in it is just stuck on the green htc screen and wont go past it...?????????
jaza20032000 said:
I can't use the SD card because I dont have the adapter thing to be able to hook it up to my comp only way i could access it was through my phone in hard drive mode. So basically i cant put any files on it without using the phone... Any other suggestions?
Click to expand...
Click to collapse
i would say buy one only cost about £5 to £10 uk pound
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: http://forum.xda-developers.com/showthread.php?t=575524) with the radio file from this link:
http://megaupload.com/?d=HT7ZMDGH
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
EddyOS said:
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: ) with the radio file from this link:
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
Click to expand...
Click to collapse
Where do I get jus the CustomRRU.exe..?? For miri?
Edit: Just read post again you included link in last quote, yes i know i am retard
I put a link for it in brackets (found here: ) - use your eyes!! lol
if you're not prepared to read what people put then don't ask for help
EddyOS said:
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: http://forum.xda-developers.com/showthread.php?t=575524) with the radio file from this link:
http://megaupload.com/?d=HT7ZMDGH
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
Click to expand...
Click to collapse
I am using a HTC LEO (HD2) with EnergyROM installed in it. Now I was tryin to flash updated version (11th march update), But I am having trouble with Activesync which somehows is from last few weeks. It connects & syncs the device too once USB is plugged in, But disconnects when I try to flash a rom using customRUU..It gets disconnected on the bootloader screen & activesync status turns to Disconnected from Connected..I pull out my battery & restart the device again. This is highly irritating & I wish if there's some other program instead of Activesync that could be used to flash a rom.
I tried doing it with bootloader screen, Turning the device off, then turning it on while pressing down the volume button, It sure goes into bootloader screen, but shows Serial at the bottom & not USB..So any ideas for what could be the alternative for people who face the same problem with activesync, Instead of wasting time to rectify this error, Its better to find some other alternative. My PC is running Windows XP 32 bit, I re-installed my windows when i had trouble almost a month back & activesync worked fine then, But just can't afford to do it every other week or so
????
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
when i do this hd2 says NOT ALLOW What should i do??
sbugra said:
when i do this hd2 says NOT ALLOW What should i do??
Click to expand...
Click to collapse
Flash via pc
ClydeB1 said:
Flash via pc
Click to expand...
Click to collapse
done it. thnx
vicky_crispy said:
I am using a HTC LEO (HD2) with EnergyROM installed in it. Now I was tryin to flash updated version (11th march update), But I am having trouble with Activesync which somehows is from last few weeks. It connects & syncs the device too once USB is plugged in, But disconnects when I try to flash a rom using customRUU..It gets disconnected on the bootloader screen & activesync status turns to Disconnected from Connected..I pull out my battery & restart the device again. This is highly irritating & I wish if there's some other program instead of Activesync that could be used to flash a rom.
I tried doing it with bootloader screen, Turning the device off, then turning it on while pressing down the volume button, It sure goes into bootloader screen, but shows Serial at the bottom & not USB..So any ideas for what could be the alternative for people who face the same problem with activesync, Instead of wasting time to rectify this error, Its better to find some other alternative. My PC is running Windows XP 32 bit, I re-installed my windows when i had trouble almost a month back & activesync worked fine then, But just can't afford to do it every other week or so
Click to expand...
Click to collapse
It's not possible to connect to Activesync while being in the bootloader mode (The hd2 says "USB" on Windows without activesync too), so it has nothing to do with Active sync. Try another USB-Cable or use the sdcard to flash (see amma2005's Post, but as far as I know, there is no need to format the card again).
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
Great advice mate.
Been a rom junkie for weeks, bouncing around several releases to find the one.
turned towards Dutty, flashed and got a wihte screen for my trouble. Followed your advice and now running CDLC V2 "dutty" without a hiccup.
eng.mohammad said:
Dear Friend;
i faced the same problem and thanks my ALLAHH, i found that the connector copper pin that connect the battery with the phone is not in its right direction so i used my hand to redirect it to can connect with the battery
Click to expand...
Click to collapse
Hi. Can you help with this? or anyone?
leo70 said:
Hi. New here. Done this magldr 1.12 and leo70 rom but my phone playing up badly after a lot of droid and 6 and other flashes. I can't install hardly any rom any more without it - ie: stock, wm6, android, wp7 rebooting constantly for no reason etc.
Done mtty and have bad blocks - about 16 and 16 reversed. done task 28 and task 28 55aa, and task 29 as read in other threads. tried everything with different radios, different nand droid. multiple wp7-hd2 installs. but still reboots.
Any thoughts? If go back to stock+spl1.66 and send back under warranty anyone know/think if they will fix it and/or replace it? they still have old sealed replacement hd2 stock or boards much? do they do diagnostics and look at bad blocks properly on warranty return? Even on stock-rom and stock-spl still does this reboot although not as much. Worried that stock-rom wm6 will "work" too well and they won't check blocks. What about task2a? etc? Any way to install wp7/magldr and partition right so no bad blocks counted in?
Thanks very much.
Will pay for fix that works - $.
Click to expand...
Click to collapse
I am stuck on DFT boot screen after hspl, htc, magldr- for windows phone 7 on hd2. Sometimes get thru to windows phone 7. but generally reboots. Done spl back to stock and leoimg on sd back to stock and tried task28s, 29s, etc but just reboots constantly and randomly.
Any thoughts here? What is warranty process? DO they replace at all with NEW? or new BOARDS/RAM? Gone back to 1.66 spl and sent in for repairs. because - the stupid recommended Romupdateutility HTC stock rom 'upgrade' did this damage.
and yes, was Windows Phone 7 and activated with marketplace & xbox/live.
leo70 said:
Hi. Can you help with this? or anyone?
I am stuck on DFT boot screen after hspl, htc, magldr- for windows phone 7 on hd2. Sometimes get thru to windows phone 7. but generally reboots. Done spl back to stock and leoimg on sd back to stock and tried task28s, 29s, etc but just reboots constantly and randomly.
Any thoughts here? What is warranty process? DO they replace at all with NEW? or new BOARDS/RAM? Gone back to 1.66 spl and sent in for repairs. because - the stupid recommended Romupdateutility HTC stock rom 'upgrade' did this damage.
and yes, was Windows Phone 7 and activated with marketplace & xbox/live.
Click to expand...
Click to collapse
Did you check the battery pins ? Sometimes they do get bent out of alignment and simply pushing them back into place gently does the trick.
Ive opened this thread coz many people are finding my tutorial usefull
so here goes and if it helps let me know and give me a thanks
Hi i was new to all this and installed dynamics v2.0 fully unlocked rom the other day and this is how i went about it
download this
RUU_Mozart_Orange_UK_1.24.061.35_Radio_5.50.09.18_22.24.50.09U
http://www8.zippyshare.com/v/48117282/file.html
this is a load your phone back to 1.24
to install it i did this
turn phone off hold down volume down and turn phone on you should go to the bootloader screen then plug in your usb cable to the pc,
then on the white line at the bottom on phone screen should say usb instead of serial but maybe it will need to install some drivers cant remember 100%
when it is ready open that file and click the RomUpdateUtility.exe and follow the steps in that then you will have your phone back to 1.24
next you can follow this post here and download the attachment at the bottom named DFT_XSPL_WP7FG1.rar this what u need for this step
http://forum.xda-developers.com/showthread.php?t=1195647
basically this is the install procedure u may need to install active sync (XP) or windows mobile device center (vista and 7) but i did not have to my phone automatically did this
DFT_RSPL_WP7FG1_LAUNCH allows you to load RSPL on the device:
1. Extract ALL files from RAR archive.
2. Run DFT_RSPL_WP7FG1_LAUNCH (with administrative rights to access USB)
3. Mindfully reads information text. Press “Next” button.
4. Reset your device and hold “Volume Down” button during reset to enter OSPL mode.
5. Connect your device to PC via USB cable.
6. Now you may need to install proper USB drivers. They come with Active Sync / Windows Mobile Device Center.
7. Install drivers if required.
8. Make sure device show “USB” at the bottom instead of “Serial”.
9. Press “Next” button in the wizard. It should detect your phone.
10. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
11. After successful connection it should show device codename and allows to choose installed OSPL version.
12. You should look at the screen and select OSPL version in drop down list box. You need do this because it’s not possible to detect installed version via USB.
If your current SPL version doesn't present in the list, you can choose nearest version,
BUT ONLY IF IT HAS SAME FIRST NUMBER!!
Example: You have 4.XX on the device. Do NOT choose 1.XX 2.XX 3.XX.
13. Press “Next”. Wait until comes final page.
14. Read and close window
15. Look at the device – it must reboot to RSPL.
16. If you see RSPLX.Y.Z and “CotullaRSPL” on the screen – the task done! Otherwise, please report in this thread about your problems.
17. Put some feedback in this thread for community and developers.
Installing HSPL
DFT_HSPL_WP7FG1_INSTALL allows you to install HSPL on the device:
1. Launch RSPL on the device like described above.
2. Be sure that you close RSPL wizard window.
3. Run DFT_HSPL_WP7FG1_INSTALL.exe (with administrative rights to access USB)
4. Mindfully reads information text. Press “Next” button.
5. Proper drivers already must be installed in RSPL step.
6. Press “Next” button in the wizard. It should detect your phone.
7. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
8. After successful connection it should show device codename and allows to choose HSPL or OSPL version to install. OSPL means you install stock SPL back.
9. Check device codename, if something wrong turn off computer and run to the nearest forest. Grab some water with yourself.
10. Press “Next”. Wait until comes final page.
11. Device will reboot and start to boot OS.
12. Reset it and enter SPL mode again. Be sure there HSPLX.Y.Z and “CotullaHSPL” appear.
13. Put some feedback in this thread for community and developers.
Now u are ready
you can find what custom rom you want i used dynamics v2.0 which can be found here and its fully unlocked aswell so all i all im pleased with it
http://forum.xda-developers.com/showthread.php?t=1520352
download it and install the same way we installed the 1.24 rom in the begining of this post
turn phone off hold down volume down and turn phone on you should go to the bootloader screen then plug in your usb cable to the pc,
then on the white line at the bottom on phone screen should say usb instead of serial
when it is ready open that file and click the RomUpdateUtility.exe and follow the steps in that and then you will have loaded your desired custom rom onto your phone
I hope this helps some of u out and happy modding
best regards
steve
1.24
Great guide thanks, my phone is network unlocked do you know if that will revert once upgraded? also you mention rolling back to 1.24 what does 1.24 mean,and how do i find out if my device is on 1.24 already? one last Question how are you finding the rom any issues with it?
cheers
Geoff
geofferz said:
Great guide thanks, my phone is network unlocked do you know if that will revert once upgraded? also you mention rolling back to 1.24 what does 1.24 mean,and how do i find out if my device is on 1.24 already? one last Question how are you finding the rom any issues with it?
cheers
Geoff
Click to expand...
Click to collapse
1.24 im refering to the SPL you can find your version by turning the phone off holding volume down and power button and u will see your SPL at the top,
im not sure about the unlocked sim/network im new to all this aswell maybe do a search on the forums and see if you can find the answer, but i dont know this 1 sorry :/
rom is good no issues had a cable issue yesterday that wouldnt let me charge my phone but thats down to my dodgy cable
you dont have to install this rom you can use any custom rom you like or might find out there
anyways hope this helps
Launch RSPL
Thanks a great help.. ok to use to add tunes via zune? last bit on installing the custom Rom, what ruu option do I choose?
Cheers
hehe the first stage 1.2 spl.. when I open the rom update it gives a error 208? the update utility cannot open the requested file? any ideas and do i have to down to 1.2?
edit..Windows Mobile Device has been installed but when I open it, its not connected!! I powered of the phone with volume down. I can see the spl and usb at the bottom and it installed usb drivers etc, Im I missing a driver?
thanks once again
geofferz said:
hehe the first stage 1.2 spl.. when I open the rom update it gives a error 208? the update utility cannot open the requested file? any ideas and do i have to down to 1.2?
edit..Windows Mobile Device has been installed but when I open it, its not connected!! I powered of the phone with volume down. I can see the spl and usb at the bottom and it installed usb drivers etc, Im I missing a driver?
thanks once again
Click to expand...
Click to collapse
hi u don't need to worry about mobile device center this never picked up my phone either until I installed the custom rom
Don't ask why I've no idea
So what's happening when you press volume down and power you are seeing the multicolored bootloader screen right?
If so I don't know why the rom won't install for you
Maybe I've heard your firmware is at .707 if so you need y cables and its harder to downgrade your sol
tell me the firmware version please and ill try help u its in settings then about then advance on your phone if I remember
Oh also do not extract the 1.24 from the .rar file run everything from there
This is why ur getting that error I think
geofferz said:
Thanks a great help.. ok to use to add tunes via zune? last bit on installing the custom Rom, what ruu option do I choose?
Cheers
Click to expand...
Click to collapse
you dont need to select a option just load ROMUpdateUtility.exe
ive just downlaoded and reinstalled the rom myself to try see what u mean and i dont get this option
when you go to bootloader screen on your phone and it says usb open the rom file and click ROMUpdateUtility.exe
now dont open active sync or mobile tools as it says on the program information
just click the tick boxes and continue through the process
maybe try download the rom again found this
ERROR [208] : FILE OPEN
ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
but like i sed i have downloaded the file myself and it is working for me without any problems
beany2009 said:
hi u don't need to worry about mobile device center this never picked up my phone either until I installed the custom rom
Don't ask why I've no idea
So what's happening when you press volume down and power you are seeing the multicolored bootloader screen right?
If so I don't know why the rom won't install for you
Maybe I've heard your firmware is at .707 if so you need y cables and its harder to downgrade your sol
tell me the firmware version please and ill try help u its in settings then about then advance on your phone if I remember
Click to expand...
Click to collapse
Thanks for the help.
My firmware is 2250.21.40600.61,hope I don't need y cables for this version..
I see the multi coloured screen, and once plugged in to my pc it says usb at the bottom..
Strangely the 1.24 rom update works sometimes and not others, can you remember when you do done it, did it tell you want version currently on? because it didn't for me, I pressed next until update screen and was on 0% for bout 6-7 mins, my phone also displayed the same, how long did it take roughly
As regards to the Dynamics rom update.exe ( I opened with no phone attached ) It says welcome to the advanced rom update utility for Htc Mozart below that are, two ruu options.. regular (this is default) and below is custom I was thinking or using logic that I don't think i have hehe.. that the custom would be the option? or leave it
I really appreciate your help on this, I have installed many custom rom on android,but this windows phone grr annoying but I wont give up.
geofferz said:
Thanks for the help.
My firmware is 2250.21.40600.61,hope I don't need y cables for this version..
I see the multi coloured screen, and once plugged in to my pc it says usb at the bottom..
Strangely the 1.24 rom update works sometimes and not others, can you remember when you do done it, did it tell you want version currently on? because it didn't for me, I pressed next until update screen and was on 0% for bout 6-7 mins, my phone also displayed the same, how long did it take roughly
As regards to the Dynamics rom update.exe ( I opened with no phone attached ) It says welcome to the advanced rom update utility for Htc Mozart below that are, two ruu options.. regular (this is default) and below is custom I was thinking or using logic that I don't think i have hehe.. that the custom would be the option? or leave it
I really appreciate your help on this, I have installed many custom rom on android,but this windows phone grr annoying but I wont give up.
Click to expand...
Click to collapse
lol np mate ill try help as best i can
right i understand your bit now about the dynamics rom u need to select regular on this part
custom i think would be if u want to edit it or some **** but i have no idea so u use regular mate because this is the actual rom file made but remember u must downgrade and load rspl and hspl onto your phone before doing this step
right my firmware is 2250.21.51301.401 but i dont know if this changes on installation of the downgrade and adding the custom rom like i sed im a complete noob with this myself but all went smoothly for me thats why i made the tutorial
and no mate my phone took about 5-10 mins to install the 1.24 orange rom
have u tried a hard reset first and then see if it helps with the installation
ill search around for your firmware and see if there has been issues
edit..........................................
did a search on the forums and your firmware comes up with nothing :/ did a google and only shows this thread did you type the numbers correctly?
also you mean that the rom update works sometimes and not others?
if it works once it should install it mate np's
When you load you phone into bootloader the multicoloured screen can you please type here what u see mainly the top letters and numbers
beany2009 said:
When you load you phone into bootloader the multicoloured screen can you please type here what u see mainly the top letters and numbers
Click to expand...
Click to collapse
again thanks for your help
ok here goes red: PD 67100 ss-BC (4k)
SPL-4.6.2250.0(129193) mng
what you think?
i think my SPL was on that before so i dont know why u are having issues mate :/
maybe wait and see if a developer can read this and give us some info on why its not working for you :/
Thanx For The Help And the Tutorial It Was very Helpfull
Now my phone Is running dynamic 2.0
hey can u tell me what other custom roms are available that i can install on my phone and if there are any different methods of installing them
no problem mate glad it helped
erm the only other custom rom i have seen on mozart is deepdishing v7.0 you can find this in the development thread inside mozart topics
and for me mate im not sure and have not seen another way of installing another custom rom but im new to all this myself
anyway glad this helpped
regards
my computer wont pick up htc 7 mozart in bootloader
can anyone help me its doing my head in .
when you connect your phone to pc in bootloader its not showing as usb on the bottom of bootloader screen?
just serial?
just to confirm. this wont work on Asian handsets.
beany2009 said:
Ive opened this thread coz many people are finding my tutorial usefull
so here goes and if it helps let me know and give me a thanks
steve
Click to expand...
Click to collapse
Thx for the easy to follow guide.
It worked on a telstra brand mozart using windows 8.
Sent from my GT-N7105 using Tapatalk 2