Related
I have a rom kitchen that can cook roms for startek. I am going to try to make a rom today with all the info I have found so far. My 3125 is scrap to me so if I brick it I don't care. Wish me luck I'll keep you all posted.
Just a little update, super CID unlocked the phone and have been able to manipulate some files. Attempted flashing an os.bin from typhoon but phone would no longer boot. Retrying, thought bricked device but no. I'll update as I make progress.
sledwrecker said:
Just a little update, super CID unlocked the phone and have been able to manipulate some files. Attempted flashing an os.bin from typhoon but phone would no longer boot. Retrying, thought bricked device but no. I'll update as I make progress.
Click to expand...
Click to collapse
Sledwrecker, thanks for taking the initiative on this. I also have a dormant QTEK 8500 when you get a little further along and need another tester. Let me know, I'm up for it.
Well seems as though I have bricked this turd.... I am locked in bootloader I can't recover from SD fallowing all the steps I have found around here.
Trying to D/L the qtek rom now maybe that will work.
I can't get the phone to connect to pc in bootloader mode. Phone enters bootloader, I plug in USB and it shows "USB" on the bottom left but I can't see the phone through MTTY or throught the RUU setup.
I'll update if I figure this out.
Prepare your SD card with the OEM ROM per this method and this should (hopefully) unbrick your device. Please report back so I can also know if it works in this situation. Thanks!
From the WIKI: StarTrek SD Card flashing
It is necessary to format your microsd card to FAT32 filesystem!
# Empty (erase the contents) of your microSD card from the Windows Mobile file explorer or format it in fat32 from your computer using a card reader (in some cases format doesn't work).
# Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / ~MacOS use [cabextract | http://www.kyz.uklinux.net/cabextract.php].
# Rename the .NBH file to *STARIMG.nbh* and copy it to the root folder of your microSD card.
# With microSD card inserted on the phone, start the bootloader (The bootloader is invoked by pressing down the Record button and Camera button at the same time).
# You should see the screen with SD Card searching, then confirm flashing on screen by pressing Softkey.
# Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 25 minutes, so check your battery or connect to charger before the flashing process starts.
~SuperCID devices are able to flash any official NBH image using this method.
I've tried this several times with the english nk.nbh from HTC's american rom and the CWS rom as well.
1. Extract RUU_STAR100_4.1.502.5_02.79.30_CWS_SHIP.exe
2. rename .nbh file to STARIMG.nbh
3. format "my" 1 gig micro SD card FAT32
4. copy STARIMG.nbh to MicroSD card
5. Insert MicroSD card into STarTrek
6. Power on in bootloader mode holding camera and voice record then pressing power.
7. White screen with blue text "searching for SD card"
8. Tri-Color Boot loader....
Never finds / Sees the SD card
PC sees MicroSD card just fine.
Also, as mentioned above I can't get the phone to connect via USB and bootloader either.
Here is what I KNOW I did "wrong" possibly....
1. I was in MTTY trying to upload a WM6 os.bin to the startack.
2. Ran set 32
3. It found device "ok"
4. lnbs os.bin
5. it did a format and copy
6. restarted phone
7. Nothing.......
8. Hard reset ........
9. Nothing
10. camera, voice record, power = bootloader... Works..
This is where I am at. Like I said I jsut want to get a WM6 rom working if the phone is done the oh well. I am here to help.
Try this
If you want to connect in bootloader and you see the usb connection try the following:
In Activesync, unckeck the Alloy USB connections box.
Remove the device entry from control pannel under mobile devices
plug in the device to USB
Run the enableRAPI program to try to re-establish communications
Here is also a rapidshare link to the latest OFFICIAL WWE ROM for WM5 QTEK 8500. Try it as RUU after the above, if that does not work, extract the contents and try the SD flash again. My gut says if you can get to bootloader, you haven't bricked it yet.
http://rapidshare.com/files/56652190/RUU_STAR100_3.6.251.0_02.67.30_QtekEUR_Ship.exe.html
You said
*Remove the device entry from control pannel under mobile devices
Can you be specific, I can't figure that part out? asside from removing the device entry I've done everything else.
When I try to run the enablerapi it just sits at a blank cmd prompt?
Still no luck get the 260 error when running the RUU
Start>Control Pannel>System>Device manager>Portable Devices>(Windows mobile-based device)
Remove whatever device looks like StarTrk or WM Smartphone
Well I went through device manager and can't find any reference to mobile device or startrek. still can't get the phone to connect.
SD card flashing still did not work even using the .nbh from the rapidshare link above.
When the phone first goes into bootloader it says searching for SD for about 1 second then goes to tri color screen. it's as if it doesn't see the SD card at all.
When in bootloader if I plug in the usb cable I get the little USB down in the bottom but I can't get the enable rapi to work. It just hangs or sits at a cmd propmpt
Sounds like we need to get the SD flashing to recognize your card,
Let me walk through the process with my working QTEK and the same ROM I posted to Rapidshare, then we can compare notes again.
EDIT: By the way, My IPL/SPL show 3.06.0000 and the USB connection does link when attached to my PC (Vista).
SD Flashes OK
Well, I found only a few contentious points with the SD flashing guide:
1) VERY CLEARLY states you must format for FAT32
I had to buy a new microSD for this test. It came standard in FAT16 not FAT32. Took quite some time to format it.
2) Extracted the .nbh file using WinRAR version 3.7
3) Rename the file STARIMG.nbh in CAPS as shown. This was the only file on the card and was in the root directory
4) when installing the microSD, it was necessary to put my SIM card in to keep the SD located properly.
The rest went as expected without fault.
Dude you are my personal hero.
I got it unbricked or fixed using your method.
Here is what I did EXACTLY so maybe this will help someone else.
1. Take 1 gig Kingston MicroSD card
2. Put it in SD sleave and Plug into Computers SD card reader
3. Open Disk Management by right click on my computer then "manage"
4. Selected Removable Disk
5. Format as FAT32, Cluster size = 512 and NO QUICK FORMAT and NO Volume Name
6. Extract ship.......*.nbh from official rom RUU installer.
7. Rename Ship......*.nbh to STARIMG.nbh
8. Copy to SD card
9. Place MicroSD card in phone
10. Insert SIM
11. Insert Battery Pack
12. Holding camera and voice buttons press and release power on
13. Phone searched for SD card
14. Success Phone found SD card press middle side button to start download from SD.
15. Took less than 10 minutes to complete recovery!!!!!!!!!!!!!!!!
I saw some other threads around with people stuck like I was earlier. Try this it worked for me!
Back to the cooking I'm either going to brick this phone or get WM6 working!!!
THANKS AGAIN!
I love it when a plan comes together! Good luck in the kitchen.
Haven't given up yet.. quickk update.
I've been able to succesfuly extract the WM5 ROM completely.
I've been unable yet to extract a complete nk.nbf from Tornado.
After close comparison looks like tornado is closest to Startrek. It has the same OMAP 850 Proc and architecture was going to port typhoon since it's the 730 and the 850 is basicly the same but faster.
I have got an os.bin tornado WM6, not sure what to do at this point.
----
From what I found if I use the XIP from the WM5 rom then the main drivers, keypad, etc.. should work. in theory..
Can I mesh the os.bin into an .nb file ?
I was consifering pdocwrite.exe to upload it but I need to know how to caluclate the header size. Unsure here.
Can I take the os.bin, convert it to .nb and then mesh it in with a WM5 nk.nbh?
Looking for some suggestions, if there is anything OBVIOUS that I am missing please poitn it out.
Try to contact with Erofich, sp3dev or pof, cause these gays working on this project and use the pdocwrite. So they can tell you how to caluclate the header size.
Also in this thread have some info too:
http://forum.xda-developers.com/showthread.php?t=311776
Windows nb from Typhoon
http://rapidshare.com/files/57065531/windows.nb
Here's a windows.nb we can try if you wish from the Typhoon WM6 ROM in my signature. I know you said the Tornado has similar hardware, but I think the Typhoon is also a close match. This comes from the Typhoon os.bin but I am not 100% certain of the process to make it.
(I do have WM6 working excellently on my Typhoon from this file)
I believe if you replace the WM5 windows.nb with this one from WM6 then recook it, it just may work.
k, giving this a shot
I have nb to nbf for wizard. What do you think will be the best tool to recompile the .nbh?
I'll keep reading on my own for now
Using MTTY to try and flash as 06_os.nb
Getting the fallowing error.
Cmd>lnbs 06_os.nb 0x0 0x2600000
clean up the image temp buffer at 0x8C080000 Length 0x03A00000
MTTYDownloadImage
"06_os.nb"
:F=06_os.nb
start download
S
HAddress A0000000h Length 01B00027h
Start Address out of boundary
checking image header<CE-31><CE-2034088><CE-2034088>
I've been having some usb problems with my Hermes for a while now:
- it nearly always can't charge with standalone usb chargers now - it will only charge by connecting to computer.
- connection issues with WMDC 6.1. It connects at first but after a few minutes, the activesync connection is lost [it still charges though]. I have Vista ultimate x64. I've been using bluetooth to sync anyway.
I've just thought, oh well, I'm sure the problem will go away when I finally update my rom next time. But now I can't do this, because of this USB problem. The usb connection is lost [orange led light turns off] as soon as the flashing utlity puts the phone in bootloader mode [first time I tried this today, windows was installing a "htc usb sync" driver at this point...weird]. As a result of this I get an "update error" 284 and I have to reset battery and start all over.
Should I try activesync 4.5? A different vista x64 driver (can't find any), or a different OS? I hope there's nothing seriously wrong with my herme's USB port! Can't see why, I've looked after it well.
Thanks for your help! I don't want to be stuck in WM6.0 forever!
If you have an xp machine, you could try activesync 4.5. Does your usb port look okay as far as connections to the motherboard? No cracked solder joints?
Oh yeah...I managed to keep the usb connection in by holding it in place with my finger, rather nervously, while the rom updated!
I had a good look at the Kaiser forum where they're having problems with the usb port's weird htc shape, and loose connections...I think it's the same with my Hermes.
It still can't charge with regular chargers though. Only laptop.
Mate, you can use the sd card method to update your rom if you've flashed Hard SPL. MUCH SAFER than "holding it in place with my finger".... I believe that could be a way to bricksville...
I'm assuming, of course, you HAVE Hard SPL on your Hermes...
1. Format sd card fat32 and copy the .nbh file of the rom onto it. Rename it to "hermimg.nbh.
2. Insert sd card into hermes & go to bootloader - OK button, power button and reset with stylus, hold in until tri-colour screen comes up.
3. Follow the prompts.
If it doesn't do anything then either you've not formatted the sd card fat32 or have renamed the .nbh file wrong. Make sure you have at least 50 % battery power and DON'T reset in the middle of a flash...
Easy as pie...
Cheers...
ultramag69 said:
Mate, you can use the sd card method to update your rom if you've flashed Hard SPL. MUCH SAFER than "holding it in place with my finger".... I believe that could be a way to bricksville...
I'm assuming, of course, you HAVE Hard SPL on your Hermes...
1. Format sd card fat32 and copy the .nbh file of the rom onto it. Rename it to "hermimg.nbh.
2. Insert sd card into hermes & go to bootloader - OK button, power button and reset with stylus, hold in until tri-colour screen comes up.
3. Follow the prompts.
If it doesn't do anything then either you've not formatted the sd card fat32 or have renamed the .nbh file wrong. Make sure you have at least 50 % battery power and DON'T reset in the middle of a flash...
Easy as pie...
Cheers...
Click to expand...
Click to collapse
Thanks for that quick guide to SD card flashing! I've decided I'll do that method for the much riskier radio upgrade.
Yep, I've got Olipro 2.10. Cheers!
IGNORE BELOW I GOT IT RESOLVED. On the phone itself the female usb connector had 2 of the 5 "connectors" entangled with each other inside. I am going to be careful from now when I plug any usb cables in it
Hi All
I cannot seem to sync my phone using any USB cable anymore (ERROR [260]: CONNECTION). It charges fine, but the computer does not see the phone at all. I have tried different cables, different computers, but no luck. I have Actisync 4.5 installed. When I try to reinstall the ROM also (Power + OK button) I am getting "serial" showing at the bottom of the screen instead of "USB". Any ideas what is causing this? The phone is working great otherwise. Every single feature works except USB . Note Well: The phone is NOT stuck on BootLoader screen, it boots up fine.
Is it possible it's the USB connector on the phone is damaged? But as I said it does charge the phone when connected to the computer.
PS I also did a "clear storage" to default the phone back to the current ROM I have installed and also I have checked "usb to pc" enabled on the phone.
HTC TYTN
HERM200
IPL-1.01
HERM200
SPL-1.40.Olipro
Windows XP SP3
Thanks.
If you have this problem, try the SD card method....
(assuming the Hermes has Hard SPL v7 installed)
1. Format sd card FAT32. Copy .nbh file of the rom you want on and rename to hermimg.nbh .
2. Insert SD card into Hermes and reset to bootloader.
3. Assuming all things are right, follow prompts...
Cheers...
ultramag69 said:
If you have this problem, try the SD card method....
(assuming the Hermes has Hard SPL v7 installed)
1. Format sd card FAT32. Copy .nbh file of the rom you want on and rename to hermimg.nbh .
2. Insert SD card into Hermes and reset to bootloader.
3. Assuming all things are right, follow prompts...
Cheers...
Click to expand...
Click to collapse
Hi Ultramag
Hmm, sorry it does not work for me, as previsouly discussed, it got me stuck on bootloader with 'Serial' below.
Hi,
I would very high appreciate if someone in this community could help me with the Hard-SPL upgrade problem. I read a lot of threads in this forum and in other forums. I tried to follow several solutions but I get stuck all time during the upgrade to hard spl 2.10 with an error 260.
I connected my mobile via USB cable. WMGC 6.1 is running on my PC --> synchronizing has finished. Then I started Ruuwraper on my vista PC --> after I answered yes to upgrade to hard-spl 2.10 --> on my mobile appeared enterBL.exe and was asking me if I should run it Y/N. Then I replied with yes --> afterwards it appeared the bootloader
IPL-SSPL by Desc
SPL-1.09ds
but then there is no reaction for about half a minute. Afterwards it appears on the PC "error 260" (I should check if the cable is connected via USB)
However I see that USB appears on the bootloader screen. In my opinion it should work, but didn't !
if I go into bootloader I read following :
IPL --> 1.01
SPL --> 1.04
IMG 1.23.707.4
My desktop OS --> vista 64
windows mobile center --> V6.1.6965
Can it be that I need a special USB cable for my HTC ?
Or ????
Thanks in advance for your help.
I know that there is a problem with using 64bit OS versions, so if you have another computer you can use that isn't 64bit to check whether it is that or not.
Good luck
Thanks for your fast reply.
I tried on my other computer (laptop installed windows XP SP3). However I failed with the same problem.
When i first tried to flash my device i had a problem of it not connecting to the boot loader, it seemed that every time the phone changed to boot loader the computer would no longer recognize it and it wouldn't be synced with the computer. i think i managed to get around this problem by putting my phone into boot loader (ok button + power + reset button) and then connecting it for some reason the computer would then recognize it and it would work. I cant remember what it was i was flashing it may have been hard-spl
Hope this helps, Good luck
Edit: I found this information on completely different forum that came from HTC about what to do
HTC's Answer: I was instructed to disconnect and soft-reset. Then I was instructed to go to Settings>System>Memory>Running programs and Stop All. Including Active Sync. We then reconnected the phone. Established a sync and ran the utility. Active Sync still goes away and you get the falling tone of a Disconnect. Ignore it and proceed as if everything is connected. Bang Zoom. 10 minutes later I'm loading software. *dance*
Click to expand...
Click to collapse
this is what is meant to happen as i flashed a new rom the other day on vista and windows had to find the device again and reconnect i think after this small pause it worked again.
Ok, I tried. Following result :
I see that Serial goes to USB but then no reaction. I can see on the WMDC 6.1 --> it shows still "not connected".
I found one article below and tried as well but it starts not automatecly from the bootloader too :
HERMIMG.nbh on a FAT32 filesystem
http://forum.xda-developers.com/files/hermes_sd_flashing.jpg
1. If you want to install any ROM (NBH) which is not supplied by your operator or the CID does not match then you will need to SuperCID your device. This can be easily done by installing HardSPL and should be the first thing done if doing any upgrading.
2. Empty (erase the contents) of your 2 gig or smaller non-SHDC MicroSD card (the Hermes bootloader does not support SDHC) from the Windows Mobile file explorer or format it from your computer using a card reader (in some cases format doesn't work) make sure it's formated in FAT32 format. As a precaution you might want to check the MicroSD card for file errors. i.e (Properties->Tools->Error Checking)
3. Extract the .NBH file from your preferred ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
4. Rename the .NBH file to HERMIMG.nbh and copy it to the root folder of your microSD card.
5. With microSD card inserted on the phone, start the bootloader (hold Ok button on left side and POWER button at same time and stick with stylus in RESET on bottom).
6. You should see a screen similar to the one pictured on the left (What lines appear depends on what is included in the nbh. If the file doesn't include bootloader code, that line will not appear, and so on.) Confirm flashing on screen by pressing the power button.
7. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
8. After you get the confirmation that the upgrade is complete, softreset your device.
So you tried flashing using the sd card method and still no result?
yes
and now I tried your suggestion with stop running programs activsync and calender.
Also the same --> error 260
I would've hoped that one of the methods would work, i take it the device syncs up fine normally to device center and you can access all your files etc?
This is the thread i quoted from there is some more information about the problem i don't know whether it will help though.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=42389&view=by_date_ascending&page=1
yes I can synchronize and I can see all the file via vista explorer.
I take it your planning to flash a newer rom onto your hermes, are you running the stock rom that came with it at the moment?
I just ran the hard-spl ruuwrapper.exe on my computer with out my phone connected this gave me the 260 error so it is most probably something to do with the phone connecting whilst in boot loader mode, did you click yes to run any program that it asked you to on the phone?
I did read some where that resetting the pc might work but i dont know whether it will make a difference considering you've already tried it on another computer.
Good luck
See my comments inline :
Scotty93 said:
I take it your planning to flash a newer rom onto your hermes, are you running the stock rom that came with it at the moment?
Actually I bought the HTC in Taiwan (CHT is the brand on the front) in a shop. At the beginning there was a chinese OS and the seller in the shop changed it to the english version.
I just ran the hard-spl ruuwrapper.exe on my computer with out my phone connected this gave me the 260 error so it is most probably something to do with the phone connecting whilst in boot loader mode, did you click yes to run any program that it asked you to on the phone?
yes, it appered enterBL.exe on my mobile. Then I answered with Y.
I did read some where that resetting the pc might work but i dont know whether it will make a difference considering you've already tried it on another computer.
yes, on my laptop (windows xp). The same problem -->error 260. There is only one difference between my desktop and my laptop. activsync (with windows xp) drops during using the program RUUWraper which WMDC 6.1 (with vista) does not.
Good luck
Click to expand...
Click to collapse
i dont really know what to suggest, what happened when you tried flashing it using the sd card method?
Tried already. Not working too.
program starts not automatically with .nbh file from the SD card when I went into bootloader.
you could try the sd card method again, following the instructions Here to the letter and see how it goes because that should bypass the problem of it not connecting and should work.
Scotty93 said:
you could try the sd card method again, following the instructions Here to the letter and see how it goes because that should bypass the problem of it not connecting and should work.
Click to expand...
Click to collapse
I tried again to flash via SD card but my mobile does not recognize the .nbh file. The mobile stays in bootloader mode and does nothing.
Edit :
maybe I made something wrong ? I used the .nbh file from the Hard-SPL. Is this ok ?
i have attached the .nbh file from hard-spl. renamed to what it is needed to be to work. reformat the memory card so that it is blank and in fat32 format, put this file on it and follow the rest of the steps.
Scotty93 said:
i have attached the .nbh file from hard-spl. renamed to what it is needed to be to work. reformat the memory card so that it is blank and in fat32 format, put this file on it and follow the rest of the steps.
Click to expand...
Click to collapse
Thanks. My SD card is already formatted with FAT32. Is it really necessary to format it again ? I deleted only the files on the SD card and tried it already but it did not work.
If yes to format FAT32 again, do you have also a program for FAT32 formating which is running on vista ?
I downloaded fat32format already but I have to find an adapter to put it into the PC to format. Or is there another possibility to format ?
From the PC I did not find a possibility to access to format directly on my mobile.
there is a formatter on vista but the memory card would have to be connected to the pc, when i brought my micro sd card it came with an adapter to an sd card so i can use it in a usb card reader or the one on the front of my tower.
other wise i dont know if you can format it this way whilst it is connected to the phone.
Scotty93 said:
there is a formatter on vista but the memory card would have to be connected to the pc, when i brought my micro sd card it came with an adapter to an sd card so i can use it in a usb card reader or the one on the front of my tower.
other wise i dont know if you can format it this way whilst it is connected to the phone.
Click to expand...
Click to collapse
Ok thanks. I have to buy an adapter. Then try again.
ye im afraid so i cant think of any other ways that might get your device to flash, you could always wait to see if one of the more senior members replies although you may have to wait until tomorrow.
Hello,
i have a brand Vodafone IT Titan with:
OS: 7.10.8107.79
firmware: 166.2200.20501.165
radio: 16.23.06.10_16.32.00.23U
bootloader: 2.5.160015.3(137079)
i wanted to upload the 2.05 eu rom so i have downloaded this rom: http://www.filefactory.com/file/1ybq4xqcazyp/n/IMG_Eternity_HTC_Europe_2.05.401 and obtained the file named 'IMG_Eternity_HTC_Europe_2.05.401.01_Radio_Signed_16.23.06.10_16.32.00.23_ETERNITY_RELEASE.nbh' (yes it has the apex included in the file, vary strange for me) that is 419.982 KB
i have renamed the file in ETERIMG.nbh.
i have downloaded goldcardtool and goldcard.img.
i have formatted the microSD in fat32.
i have copied ETERIMg.nbh in the microSD.
i have patched the microSD with goldcardtool and goldcard.img
i have connected the Y usb cable to the Titan, the microSD card reader and the PC.
i have booted the Titan in USB HOST mode but it always show me "Entering USB Mode". Upload does not begin at all.
So, what am i doing wrong ???
Please guys help me!!!!
nyonik said:
i have renamed the file in ETERIMG.nbh.
i have downloaded goldcardtool and goldcard.img.
i have formatted the microSD in fat32.
i have copied ETERIMg.nbh in the microSD.
i have patched the microSD with goldcardtool and goldcard.img
i have connected the Y usb cable to the Titan, the microSD card reader and the PC.
i have booted the Titan in USB HOST mode but it always show me "Entering USB Mode". Upload does not begin at all.
So, what am i doing wrong ???
Please guys help me!!!!
Click to expand...
Click to collapse
Looks likes that your Y cable is fine, with your phone showing "entering usb mode". This leaves your gold card as possibly the main culprit. In other threads, some had the same issue and managed to flash their phone by trying other type of microsd card and card reader. I used a kingston 2gb microsd card and multicard reader. I managed to debrand my att titan to european 2.05 rom (see the thread I started on this topic: http://forum.xda-developers.com/showthread.php?t=1693334&page=2)
Thanks for the replay.
I don't know if the cable is ok. I bought it on ebay:
http://www.ebay.it/itm/260747604735?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
It is a normal Y cable used for external HardDisk when a single usb port is not enought for powering the device.
I connected the miniUSB port to my card reader.
I connected the dataUSB port to my phone (using a famale-famale adapter)
I connected the powerUSB port to my pc.
The strange thing is that when i plug the phone (phone is already turned on)
then the phone fell i had connecet it and the led become red.
Also the led on the card reader is Turned on, meaning that it is turned on.
But when i restar the phone and push vol- and camera going in USB Host mode,
the led on the card reader is desapeared, so i thing it is turned off.
The phone is now waiting in USB Host mode.
So i disconnect and reconnect the power usb cablo form the pc, and so the card reader turned on again. But the upload does not begin.
Do you thing that there is something strange ?
may be i miss something on doing the gold card (wrong image, wrong name) or samething like that?
I have already tried with 4 different memory card but (512MB MMC, 1GB microSD, 8 GB microSD and 1GB SD card) the result is the same.
I have a question, after downloading the
'IMG_Eternity_HTC_Europe_2.05.401.01_Radio_Signed_16.23.06.10_16.32.00.23_ETERNITY_RELEASE.nbh'
file
I have to extract RUU_Sigbned.nbh and rename it in ETERIMG.NBH
or jusy keep the whole file and rename it in ETERIMG.NBH ???
If i have to exctract RUU_Signed, how can i do that??
I have the same question as nyonik.
After getting to the USB Mode, I plug in the phone the card reader turns on and off and it goes straight back to ther SPL screen and freezes there. When I unplug the device the word "serial" appears on the screen. I've havent been able to find someone on here describing a similiar scenerio. I've tried several different types of media and they all do the same thing.
@nyonik- you copy the euro rom 2.05 to microsdcard rename it to ETERIMG.nbh then make it a goldcard.
@jonesk001- that also happened to me, what u need to do when it goes back to spl mode, unplugged phone "serial" appears, then restart phone by pressing power button for few secs when it start to boot hold down vol- and camera buttons this will boot ur phone to "usb mode" screen, at this point plug it back to Y cable. Your phone should proceed with flashing. If it again kick back to spl mode repeat the steps i described. Goodluck.
Sent from my TITAN X310e using XDA Windows Phone 7 App
Thanks Habnzrot for tips. Finally got everything to work. Amazing enough I used WinXP to format and make the gold card instead on Win7 and it worked, using the same setup that was previously didn't work.
jonesk001 said:
Thanks Habnzrot for tips. Finally got everything to work. Amazing enough I used WinXP to format and make the gold card instead on Win7 and it worked, using the same setup that was previously didn't work.
Click to expand...
Click to collapse
Good to hear that you now managed to flash your phone Enjoy custom rom (s)!
use 1gb msd card. before I used a 4gb card it has the same issue.