Phone is a MDA Vario 2 (Herm300), though i had ran the SIM & CID unlocker succesfully a few months ago and have been using an o2 sim since.
I thought i'd upgrade to WM6 (installed it fine over a year ago) so picked the o2 one from the list on here. The upgrade went fine, it completed and i clicked Finish when i was prompted. The device first got stuck on the Windows Mobile screen then froze up when it actually goes past on to the today screen. The o2 customisation stuff starts to install but as before it freezes after 2 minutes or so, after soft reset it bypasses that and boots to Today screen. I'm also getting the No GSM message on the o2 splash screen prior to the freezing up. When it does boot up to Today screen all functions are working for about 2 minutes then it dies.
So now it wont connect to activesync and nor will it respond to any SD card install. Bit cheesed off, had my head in the Wiki almost all day trying things out but with no joy and something that was straight forward over a year ago has turned into a nightmare and my brain now aches.
Is there any way i could get back to the default tmobile rom? All i'll do then is run the SIM & CID unlocker again and leave it at that. I only wanted WM6 for the HTML emails.
You didn't flash Hard SPL V7, did you?
You can try installing the stock rom back again but if you can't get it to run you're in for a world of time consuming reading....
You MUST Install Hard SPL V7 if you recover your Hermes as it makes it easier to recover if something like this happens...
ultramag69 said:
You didn't flash Hard SPL V7, did you?
You can try installing the stock rom back again but if you can't get it to run you're in for a world of time consuming reading....
You MUST Install Hard SPL V7 if you recover your Hermes as it makes it easier to recover if something like this happens...
Click to expand...
Click to collapse
The device was CID & SIM unlocked first. The bootloader shows IPL - 1.04 and SPL - 1.40.Olipro
How can i install v7 if activesync wont connect?
use the sd card method explained in the readme that comes with hardspl
skeeve666 said:
use the sd card method explained in the readme that comes with hardspl
Click to expand...
Click to collapse
Yeah, remembered that one. I'm doing that now as i speak, just formatted the 2gb card to FAT32. I'll be back with the results shortly
Imanaged to install the Hard SPL on my device via SD card. Fortunately now and again my device boots to today screen, but only for about 2 minutes before the whole thing freezes up and has to be reset.
So during this time i copied the SSPL-HERM.exe to the phone from my SD card, deleted it once copied and took the battery out. Then when i powered device up into Bootloader i just followed the instructions, pressing the power button then the install was complete. Took about 5 seconds.
So now my device is Hard SPL-2.10.Olipro.
Am i right in thinking that now my device is prepared to be flashed? I still get the No GSM warning at the o2 splash screen and the device still crashes after 2 minutes, thats if it got that far after it gets stuck on the Windows Mobile screen.
I'm thinking now i might be better off reverting back to the default tmobile branded WM5 that was already installed.
Try installing that 1st. It may fix things.
If it does, do the search for how to fix bad blocks as it sounds like this may be a problem too.
As you now have Hard SPL V7 installed, after you check for bad blocks, you can then use the sd card method to flash whatever rom you please. I believe its safer than using the PC simply because the only things that will interrupt the flash are flat batteries, manual reset and taking the sd card out during flash.
Good luck...
ultramag69 said:
Try installing that 1st. It may fix things.
If it does, do the search for how to fix bad blocks as it sounds like this may be a problem too.
As you now have Hard SPL V7 installed, after you check for bad blocks, you can then use the sd card method to flash whatever rom you please. I believe its safer than using the PC simply because the only things that will interrupt the flash are flat batteries, manual reset and taking the sd card out during flash.
Good luck...
Click to expand...
Click to collapse
I followed the instructions for flashing with sd card using the tmobile WM6 rom, which told me to extract the nbh file from within the rom and rename it loading it to the sd card before restarting the device to bootloader.
I did this and it said it was completed after what must've been only 5 seconds. Something must have been wrong with that. Especially as it still boots an o2 splash screen.
What am i doing wrong here? I'm sure i have followed every guide to the word so i'm a bit lost.
Once i've downloaded the rom i want, what do i put on the SD card in order to flash from it?
3 things...
1 MUST be 2Gb card or less.
2. MUST be formatted FAT32 - comes default format FAT.
3. Spelling has to be correct. Must be hermimg.nbh, no mistakes allowed.
Check these things, never failed for me as I don't use the P\C to flash since I found out how to do this...
Cheers...
3 steps.
1. Format sd card FAT32 and copy .nbh file onto it, rename to hermimg.nbh.
2. Insert card into Hermes and reset to bootloader.
3. If everything is right, follow directions.
Easy...
I've done it! Yay
**** knows where i'd be without you guys. BIG BIG thankyou to all who posted useful information for me to read in the forums.
It took a while but eventually the v3a unlocker got there. Booted the phone up and it now seems to works fine, it hasn't frozen up either.
Related
Hi All,
I'm new to the PDA-world and the Hermes. I'm trying to Hard SPL my Hermes, but it fails everytime.
When I run 2.10 - Hard-SPL-V7, it kills activesync and my connection is lost and I get always the message "error 260, Update error".
I have the latest framework edition and tried it on 3 pc's (1 Vista, 2 XP)...
What am I doing wrong?
Hope somebody can help me....
Kind Regards,
Micha
1). dont connect to active sync. open active sync and untick "allow usb connections".
2). put hermes into bootloader and connect to usb.
3). run ruu_wrapper.exe
should update to hard spl....
dont forget to tick "allow usb connections" again or you wnot be able to sync..
error 260 is an open port error.
if you wish to flash new os would advise to use sd card method. its safer than using the computer. just make sure you have greater than 50% battery power. happy flashing
Thnx, will give it a try.
First I have to flash HardSPL before I can flash a new OS, don't I?
yep, sorry, should have said run the ruu_wrapper for hard spl. My bad...
im having the same problem. I also tried the way ultramag recommended but i also received the same ending. After time i try i get the Error 260 Update error. Im running SPL 2.04 and the HTC WM6 rom from the HTC website. Does any one know what the problem is?
ultramag69 said:
2). put hermes into bootloader and connect to usb.
Click to expand...
Click to collapse
NOOOOO, that won't work, you need the SSPL to deploy to the phone, if you're running stock HTC bootloader this won't work at all, otherwise we'd have no need for Hard-SPL
hey olipro, then how would i fix this. Im running the stock rom from the HTC website with no hacks. Im trying to load PDA Corners V9 rom. Any ideas on how to fix? thanks!
Take a peek at the guide i wrote about updating the hardspl. Theres some explanation about why we need to use SSPL and the procedures.
http://www.mrvanx.org/hermes_guide/hardspl
thats the guide i used. it still gives me the error. I even unchecked "allow connections" cause i read somewhere that that would help.
i did this two days ago on my phone, im running windows vista on my home laptop and got any number of errors and problems trying to do it via sync with the phone (even after reading the vista troubleshooter, with the drivers etc)
What i ended up using was the memory card upgrade, dump the file onto the memory card and go into bootloader with the card installed.
worked fine doing that way, maybe less risky as there is no chance of the usb cable coming out.
just make sure you have a good battery charge on the phone.
Help Help Help w bricked 8525
I got into this position trying to upgrade WM5 to WM6 from HTC site.
Process got to 20% and just stayed there.
I reconnected usb cable and got a vendor id error
Then I get the Error [260]: CONNECTION
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
I believe this is the bootloader? I have downloaded RUU_signed.nbh, renamed it to hermimg.nbh, installed on root of my SD card and held OK, soft reset and power button:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
All post indicate that the device can be reflashed and have the OS reinstalled. I can't get there from here.
Can anyone please help?
blackdog9692 said:
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
Click to expand...
Click to collapse
How big is your SD card? Flashing only works with cards <2GB. Also, sometimes certain cards just don't work for flashing, and just swapping to a different card fixes the problem.
I assume you searched the wiki, and found the relevant pages on the Hermes (including SD Card Flashing and other things about flashing/upgrading) there?
Still Lost
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen. When i attempt to flash the rom via PC to WM5 or WM6 i get the Error 260, i also get a vendor ID error sometimes.
How can i find the key 8525 thread that i am told has the answer to my delima? I keep picking up bits and pieces but am missing some key steps and tips.
blackdog9692 said:
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen.
Click to expand...
Click to collapse
That sounds like the SD card is formatted incorrectly. Make sure it's formatted using fat32, nothing else will work.
Still not there from here
Thanks for your help. Before I formatted the SD FAT32, nothing would happen doing the bootloader reset. OK/ON/reset button.
After format and only the hermimg.nbh file renamed as indicated, I then get what looks like the loading process but back to the bootloader screen.
Q1: This is an AT&T 8525, it was perfectly fine before failure from WM5 to WM6 (process froze at 20%), what is the RUU file that I need to put on SD??
Q2: After "Loading ..." I try the WM5 PC upgrade of ROM via USB cable, I get the load process to appear to work but it gets to 1% and the phone reboots and the PC reports error [294]: Invalid vendor ID. If I do this again I will get the Error [260]. Ive repeated the process several times.
Is this the normal course to take or should the "SD Method" (with the WM5 or WM6 RUU.. file) complete the process to a working OS?
Q3: Is my situation hopeless? ATT will take my out of warrantee 8525 and reflash for $129. Reading the threads it seems that like me this can be done by me, this is my desire.
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
The newbe guide has been off line. I will look again. Is there a single place to read about "radio PDAs and the 8525 and understand the software build and custom options?
Sy for the long post. But still want to fix if possible or I will be force to mail in for ATT repair.
Thank you all.
blackdog9692 said:
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
Click to expand...
Click to collapse
Oh boy, you haven't installed HardSPL? You are walking a bit of a line there mate...
HardSPL is a custom boot loader that makes bricking your phone when flashing much harder to do, and helps large amounts in the recovery process if you phone does brick.
Does the phone boot at this point? If so, do not try flashing the phone again. Go get a copy of HardSPL and install it, then try flashing from the SD.
I still wonder why people didn't read before bricking...
Anyway, you should start reading now and wiki is your friend. Your SPL is 2.03, so look at the bottom of the page (there is only one solution till now, so good luck with that):
Code:
1. Boot OS using KITL+PB
2. Do no disconnect your HERMES till the end of the step 6
3. Download SSPL on HERMES by wifi from ie explorer
4. Launch SSPL then flash Hard-SPL from your computer
5. Put your hermes in bootloader mode
6. Flash any radio in NBH format from your computer
Still researching and working this bricked 8525
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
I then put it on an SD card and held the keys and reset. The device displayed a white screen and "Loading..." appeared. Afterward the 8525 returned to the stipped boat loader screen and that is where I am now.
Some of the help i receive and read on wiki threads has me confused with what to do next and how "exactly" to do it.
It does seem that I am not alone and people have fixed their phones and the process to do this is on the forum. I'm just still missing something.
Help me further if u can.
Thank you.
blackdog9692 said:
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
Click to expand...
Click to collapse
FYI: bad form to PM someone and post the same thing here. Keep it in the thread so others can be helped as well.
As I replied in the PM, if I'm understanding your post correctly, the phone boots to the tri-colour screen?
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
jdc said:
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
Click to expand...
Click to collapse
We already know that the phone is without HardSPL, according:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
Click to expand...
Click to collapse
There is small chance (read my previous post) to unbrick device with SPL2.03 so better try to get this back from where you take it.
And please, change topic, because this brick isn't HardSPL fault at all.
Edit: oh dear, it's even not your topic ...good game, I'm off
--------------------------------------------------------------------------------
My Mogul was taken to a store that flashes phones to cricket. So it was ok before I took it to the store now. When I turn the phone on it boots to the smart mobility screen says "No Radio" then turns right off. I formatted my microSD card put the TITAIMG>nbh file on the card put my phone in the bootloader mode. Now my phone turns on and stay in the smart mobility screen w/ the No Radio still on it, and thats it. Is this phone dead? If not HELP!
forlovebeyou said:
--------------------------------------------------------------------------------
My Mogul was taken to a store that flashes phones to cricket. So it was ok before I took it to the store now. When I turn the phone on it boots to the smart mobility screen says "No Radio" then turns right off. I formatted my microSD card put the TITAIMG>nbh file on the card put my phone in the bootloader mode. Now my phone turns on and stay in the smart mobility screen w/ the No Radio still on it, and thats it. Is this phone dead? If not HELP!
Click to expand...
Click to collapse
If you paid someone to flash it, take it back! Did they give you back a non working phone? You'd think they would have tested it???
It sounds like you have a rom / Radio incompatibility problem. Or no radio at all. You say that you put the radio nbh on the card and put it into bootloader mode, but did you actually flash the radio? Did it come up with the grey screen and blue progress bar showing it was actually flashing the Radio rom?
Mogul Dead
No my phone did not do any of that stuff. And no I do not think that I flashed the radio I don't know how. I put the nbh file on the card insert it put it in the tri color screen and nothing happens. Man I am screwed. The kid at the store is saying that I did something & I did not. I have been reading alot cause I do not know anything about this flashing stuff and it does seem like there might be a radio/rom compatability thing going on cause the phone says no radio. I followed some forum steps to no avail.
dude if you get the tri color boot loader screen you did not kill your phone, all you need to do is flash your radio, witch is completely seprate from flashing your OS. just read the wiki and relax
The phone is telling you what is wrong "No Radio" you should be able to flash a radio via your sd card then flash a rom and all should be well. You just need to make sure the radio is compatable to the ROM. What is your ROM Version that shows on your boot screen. Also what bootloader is installed (tricolor screen)
I realize English isn't your primary language, but based on how you phrased your last comment, it sounds like you are inserting the SD card after the tri color screen.
The card needs to be in the phone before you press the 3 buttons for the boot loader screen, then it should see it.
BTC
Mogul Dead
Ok great sounds like from the replies that my mogul is not dead. Ok thanks guys. Also when I put the phone in the bootloader modethe tro color screen the card is already inserted, and the bootloader is SPL-2.40.Olipro. I do not know what ROM was put on the phone when it came from the store. So yeah I just might have to keep tyring to combine the right radio for the right rom thats on the phone.
find radio 3.42.50 and flash it via your sd card
then find the rom you want .....example.... DCD 3.2.6 and flash it via your sd card
then install dcd's carrier cab for you carrier and you should be up and running
Mogul Dead
How do I flash DCD's ROM to the sd card I never did this.
Do you have a ROM ready to flash? If so just goto the wiki link for the Titan's and do some reading. Everything you'll ever need to know about flashing is in there...
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
Focus on the radio first, once you get it flashed, then you can worry about flashing the rom.
For the rom (not radio) it's much easier, from the tri-color screen, plug in your USB cable and run the .exe file and it will flash.
However, get the radio updated first.
Try the 3.42.50 radio, I personally use 3.42.40 but they are very close and both support the same roms.
BTC
Freaking out as well
I'm stuck at the tri-color screen after updating the bootloader to 2.40.Olipro , I thought I could update the bootloader and still go into my Windows 6.1 install (and update the rest later).
I thought I totally screwed up my phone until I read this thread so hopefully there is still hope for this.
I do not have an SD card so I'm trying to do it the USB method by downloading the "ROM Update Utility" and placing the TITAIMG.NBH file into the RUU directory. It seems to work but stops at about 8% and the phone goes black then the PDA Phone ROM Update Utility pops up a:
ERROR [328]: INVALID COMMAND
This update utility cannot be used for your PDA Phone. Please check your Update Utility.
As you can imagine I'm absolutely panicked right now and will appreciate ANY help!
well save yourself some grief and buy a 2 gig microSD card. Then all you have to do is put the radio ROM on it, go into bootloader mode and let it flash. That is the safest and easiest way to do it. Also less, read nill, chance of bricking your phone.
Ok I'm heading out the door to Best Buy right now...
So once I get the radio installed, I then install DCD using the SD card method? Then the carrier cab?
I've already updated the bootloader to 2.40 using the USB method, will mixing these two cause any issues?
Now that I'm totally stuck at the bootloader, are there any precautions I should take before continuing?!?
Thanks so much for the help, I can't wait to get this going and maybe help out people like myself in the future
I got a 2gb card, formatted it to FAT32, downloaded 3.42.50 radio, renamed it and placed it into the root directory of the card.
I then put it into the phone, then did a POWER+CAMERA+RESET. It comes back to the bootloader screen doing nothing.
I've been reading around and it looks like I'm doing everything correct???? It just sits there and at the bottom it says "Serial"
EDIT: Oh you have to HOLD that combination for a couple seconds. Got it, I'll keep going on the process....
Here's what I just recently posted in another thread for someone wanting step by step instructions on how to flash the phone. He said he followed it and it worked so hopefully it helps you out.
1. Download everything you will need.
a) nueSPL 2.47 from http://www.nuerom.com/BlogEngine/pag...HTC-Titan.aspx
b) Radio 3.42.50 from http://forum.xda-developers.com/showthread.php?t=415364
c) The ROM from http://www.scottcrosler.com/
2. Back up your SD card and then format your SD card into FAT32 with less than 4kb cluster size. Open My Computer, right click on your SD card, select format and adjust the settings accordingly.
3. Run nueSPL 2.47 on your phone with your SD card in. It will reformat your SD card again and put the bootloader on it. When you reset your phone it will install the bootloader. Just follow the instructions.
4. Copy the nbh file from the radio rom onto your SD card and rename it to TITAIMG.nbh. Put it in your phone and put the phone into bootloader mode by pressing CAMERA, POWER, and RESET (the recessed button on the bottom of the phone) at the same time. When it starts up it should come up with a grey screen telling you to press POWER to continue flashing. Do this and wait for it to complete. When it is complete delete the nbh file from your card using your computer.
5. Put the phone into bootloader mode again using the same method as before. Connect your phone via USB to your computer and run the ROM flashing exe to flash the rom. Just follow the instructions that come up. It's easy. When that is done your phone has the ROM installed. If the USB method does not work for you, look for the largest .nbh file and copy it to your SD card, rename the .nbh file to TITAIMG.nbh again, and reset into bootloader again. You should get the same screen as you did when you flashed the radio. When it's complete the ROM is installed.
6. Run the CAB file from My Documents to extract all the other cabs. After that is complete look for the cab for your carrier and install that. Soft reset.
7. Your phone should work now.
I think that's it. Anyone else feel free to correct anything I probably have wrong... I just wrote that from memory. It's normally easy to do and you just follow the on screen prompts so I might've made some mistakes. I always just flash via SD now because it's so easy and I don't require a PC for anything.
Click to expand...
Click to collapse
The bold text is a step I left out for the other person but he figured it out.
Edit: Oh yeah, skip the part where you install the bootloader (step 3) since you're already running an unlocked bootloader and don't have a working OS on the phone to install 2.47. Once you have a working OS you can go ahead and update from 2.40 to 2.47 if you want a slight improvement in performance. It will not require you to reflash everything else again (or at least didn't for me).
Yes! 100% working. Didn't even have to call Verizon to reactive it, everything was ready to go as soon as I got the new rom.
Thanks for the help!
sprint no evdo no gps
phone works great but cant get online and gps does not work but phone service works ? damn and its only 24 hrs old i broke it using rom and raido from above
kyjelly said:
phone works great but cant get online and gps does not work but phone service works ? damn and its only 24 hrs old i broke it using rom and raido from above
Click to expand...
Click to collapse
Did you install the carrier cab?
Also see in EPST. If you use EVDO, may be login and pass are erased after flash. I had same problem with official Sprint ROM.
And what kind of GPS you are talking about? aGPS?
Alright so about 3 weeks ago i started upgrading my hermes. i started off by downloading the 2.10.Olipro hard spl and radio version 1.16.00.00. i unlocked the cid as well. then i put this rom on with no problems. http://forum.xda-developers.com/showthread.php?t=458456
Now everytime i try to load anything from my usb my phone gets stuck in bootloader and i get a error 260 message saying my phone is not connected to my pc. ive tried multiple cables and updated my activesync. even if i try to use the sd card method i get stuck in bootloader yet again. ive been trying everything i can find on this forum for the last 5 hours and i feel something like this.........im quite the newb in this stuff so i figure this is a easy fix that i keep overlooking.
SD card method....
1. Make sure SPL is 2.10 olipro & battery is charged.
2. Format 2Gb or less sd card FAT32 and copy .nbh file to it. Rename to hermimg.nbh.
3. Insert sd card into Hermes and reset into bootloader - hold ok button above flywheel, power button and reset with stylus. Hold in until tri-colour (bootloader) screen appears.
4. Follow the prompts.
Easiest and safest way to flash ROMs...
Cheers...
If you need to use sd card method to flash Hard SPL, read post 1160 on page 116 of this thread - http://forum.xda-developers.com/showthread.php?t=296722
or just give him the direct post ultramag69
http://forum.xda-developers.com/showpost.php?p=2048832&postcount=1160
Yeah, you could, but this way he has to search a bit and get used to the ui at XDA-Developers... Might even decide to use the search function, horrors....
I was actually going to add that he might use the search function too but thought i would give you room to reply
Bought my M3100 2nd hand in June 2008, never had a problem.
Today the radio started going nuts. The phone started showing "no network connection symbols" in the top bar, most of the time.
Occasionally it did find the network (Three) and would allow me to call voicemail, but with very very bad sound quality and the odd squeaking and electric buzzing noises in the background - most of the time it dropped the call after 4-5seconds.
Quite often the phone would stall when I tried to bring up the dial pad and dial a number or tried turning off 3G//UMTS in the Comm Manager.
Getting ready to take it back to the shop I bought it from, I tried to reload an Orange rom (SPV_M3100_ROMUpdate_1007) and when that failed HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108. In both cases the rom upgrade failed at 12% with error 262.
I repeated flashing several times, on 2 different Windows XP computers and several different cables as well.
M3100 running TNT.19199_Professional_Hermes (before it failed)
HERM100
IPL-1.04
SPL-2.10.Olipro
Any suggestions?
Use sd card method.
1. Format 2Gb or less sd card FAT32. Copy the .nbh file onto it and rename to hermimg.nbh.
2. Insert card and reset to bootloader.
3. If you haven't stuffed up the other steps, follow the prompts.
Cheers...
ultramag69 said:
Use sd card method.
1. Format 2Gb or less sd card FAT32. Copy the .nbh file onto it and rename to hermimg.nbh.
2. Insert card and reset to bootloader.
3. If you haven't stuffed up the other steps, follow the prompts.
Cheers...
Click to expand...
Click to collapse
Thanks will try that. I take it you are trying to rule out a USB problem?
Eureka! Install completed successfully. Thanks for the tip.
Unfortunately the phone problem persists. Any suggestions?
If not, is it possible to re-apply the Orange Sim Lock? The company I got the phone from apparently considers it grounds to void the warranty, if one unlocks a purchased phone.
Looks like that the flashing from SD worked first time was a fluke. I have subsequently tried it again and it stalled at GSM.
Is this a physical problem with the Hermes or should I try following the corrupted radio repair guide?
Just to be clear, I haven't played with the rom in 3-4 month. The problem of the Hermes stalling when starting phone related functions, not being able to find a phone signal and dropping calls after 4-5 seconds started out of the blue.
Sorry mate, sounds like your radio rom is corrupted.
You could try to re-install the stock rom but if it keeps freezing it means that you won't be able to use as a phone. Look around on here for mr vanx spl downgrade guide, it should be able to help you restore your proper spl so you can take back.
If you can't install the stock rom then you could at least install a stock rom without the radio part. This will allow you to use the PDA functions but no phone functions...
Cheers...
Thanks for the help!
I took my chances with the shop and they just replaced it with another!
I am about to unlock/install TNT back onto it. OooOOoooh happy days!
Regards
Malte
Sweet... I love happy endings....
I'm having the hardest time getting HardSPL on my Cingular 8525. I have linux so I REALLY don't want to have to use Windows to get this working. It's a huge hassle to get the phone working under VMWare. I've already tried that.
I'm trying to get it to load via SD but I'm having no luck.
Anybody know how to get HardSPL installed without a computer? Just an SD card?
Yes you can flash from the SD Card:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Hmmm...I tried that but let me try it again just to make sure I was doing it correctly. I might have misspelled the file name now that I think about it.
Ok, just tried it again and this time when the "Loading" screen came up, it stayed up a bit longer and flashed some red numbers across the top of the screen before finally going to the bootloader screen with the color bars. It says:
HERM100
IPL-1.01
HERM100
SPL-1.06
Serial
And that's it. I'm leaving it a bit to see if it does anything else before I reset it.
Update: Never did anything after about 10-15 minutes. Did a soft reset and then brought up the bootloader to see if I had a new SPL but the screen just displayed what it was showing before.
Edit: Is there anything I need to do with the phone before it will let me flash HardSPL to it?
Alright, nevermind. I'm pretty dumb sometimes.
I just tried SSPL and it worked perfectly. I now have SPL-2.10.Olipro on my Hermes. Off to install WM6 now!
Alright, so I went to go install the latest version of the ROM as provided by AT&T using the sd flash method. I extracted the nbh file and renamed it. Strangely, it was much smaller than I expected it to be.
I rebooted into the bootloader and it came up and asked if I wanted to upgrade. I of course said yes. Then, it took only a few seconds to fill the progress bar and said it was done. I was expecting it to take at least 5 minutes to flash it. It also didn't reset on its own to I did a soft reset (should I have done a hard reset?) and it came back up into WM5 with all my data.
Is there something I missed? the nbh file was only about 250k. Should I have done a hard reset instead? How exactly does this work? Is the ROM portion of the memory just the part that it restores factory settings from and so when you do a hard reset, it then installs the new ROM to the phone?
You probably still have Hard SPL file on sd card. Rom should be anywhere from 30 Mb to 80 Mb. Recopy the .nbh file across. You still need to rename the .nbh file to hermimg.nbh or it won't recognise the rom flash. Don't use the steps using SSPL.exe (Soft SPL) you used for Hard SPL as you now have Hard SPL installed and don't need SSPL.exe.
Cheers...