Related
im facing another problem again...
this time i changed the file extension EBOOT0502_MNT_01.01.03.nbf to EBOOT0502_MNT_01.01.03.nb0
(file from HP official WM5 SP34074, inside the installed folder )
and copy to memory card and put in 6828 then started to go bootloader screen
few minutes later my screen goes blank, and i tried with the revive methods
which is
-press the 2 softkey " - " and reset button
-put in the battery ,
-release reset, then release softkey
but didt work out!!!!no repsponse at all..tried many times..possible dead ad???
plz help me abit ..big troblem!
p.s srry for my bad english
Did you rename it to eboot.nbo ? Have any files in root folder of your miniSD ?
Who make you try this way ???
i rename as i mentioned above with the long name only change the .nbf to .nb0
i also regret now coz cant even see anything from the screen >> althought tried reset eith all the mothod..
izzit my 6828 dead ad?
cant even repair by myself and have to send it back to hp for repair?
williamSun said:
i rename as i mentioned above with the long name only change the .nbf to .nb0
i also regret now coz cant even see anything from the screen >> althought tried reset eith all the mothod..
izzit my 6828 dead ad?
cant even repair by myself and have to send it back to hp for repair?
Click to expand...
Click to collapse
If you don't rename to eboot.nb0 => Your device didn't flash it => Your device not dead. Have another files in the root folder of miniSD card ? List for me!!!
--Try this way :
Press both softkeys (two "-" keys) and remove battery then insert battery again (don't unpress two softkeys) and softreset, wait 2-3 seconds. It'll go bootloader mode. You can flash your device again.
hmm, tried u way ad didt make it to boot screen..>.<
in case i rename to eboot.nb0 >>i not really sure<<
>>izzit case sencetive?
>>izzit 6828 dead??
williamSun said:
hmm, tried u way ad didt make it to boot screen..>.<
in case i rename to eboot.nb0 >>i not really sure<<
>>izzit case sencetive?
>>izzit 6828 dead??
Click to expand...
Click to collapse
What is your current bootloader, 1.01 or 1.05 ?
If you follow that menthod but it didn't go to bootloader, your bootloader was dead.
You can send it to HP to repair, or try this way : http://wiki.xda-developers.com/index.php?pagename=DeadBoot
I recommend to sent it to HP.
while the PDA is still can open and bootloader screen
is 1.01
and im trying to use the EBOOT0502_MNT_01.01.03.nbf which found in the
HP official RUU PC flash ROM
and rename to EBOOT0502_MNT_01.01.03.nb0
then put in the root of memory card
then start to flash ..
now the PDA wouldn't reapond to any button HR, SR, soft-key + reset ...etc
only can charge and orange LED indicated
williamSun said:
while the PDA is still can open and bootloader screen
is 1.01
and im trying to use the EBOOT0502_MNT_01.01.03.nbf which found in the
HP official RUU PC flash ROM
and rename to EBOOT0502_MNT_01.01.03.nb0
then put in the root of memory card
then start to flash ..
now the PDA wouldn't reapond to any button HR, SR, soft-key + reset ...etc
only can charge and orange LED indicated
Click to expand...
Click to collapse
You was flash wrong bootloader due to make your device dead.
Now you need restore bootloader.
If you send to HP, they will replace board you must pay for it.
But you try the JTAG menthod to restore bootloader it'll make your warranty expired.
thx for all ur answer, i really appreeciated.
btw, for sure hp center will replace a board in it and that will be expensive rite?
if i sent to other shop which is not HP official service, will they do the same?
izzit juz flash using tools they hv>?
and expensive?
Here is what I did ... might help you
Hi
Make sure your phone is powered, it would be wise to charge the phone via AC power at least for 1-2 hours before you try to install anything.
I finally managed to install WM6 on my HP ipaq rw6828. But it wasnt easy, it took me 1 full day to get it installed. Just to help other people who are installing this, here is my experience -
What all I did and how I finally got there -
1.
Tried to install it via PC. When I already had a higher version of the Bootloader installed. Best way is to install it via 1GB mini SD card.
2.
After reading other posts I managed to downgrade the bootloader to version 1.0.1 (not sure of the version number...but its the version you get after installing the HP SP34074).
3.
Once I managed to downgrade. I got into the Bootloader mode on my device( its pretty simple to get into BL mode, make sure you ask someone to help you with it, its easier with two people, to get into Bootloader mode - a)press the two "-" buttons on the phone together. b)While the two "-" are pressed have a second person remove the battery. c) Wait for a few seconds and ask the person to insert the battery back. d)Once the battery is in place ask the second person to use the stylus and push into the soft reset hole (its hole on the left of the USB connecter on the phone). e) Wait for a few seconds and then phone should go into the BL mode. f) release the two "-" buttons after it enters the BL mode. Sometimes for me it entered the BL mode after I released the "-" buttons also. But dont release the "-" buttons till you have pressed into the hole with the stylus.
4.
With my phone now in the BL mode and showing the older version 1.0.1 (not sure but it should not be 1.0.5) I clicked the Device Software Update Utility.exe. I got the screen where you get a combo/dropdown with "ALL" pre-selected. The install step clearly says choose "OS" only and not "ALL". But I made a mistake here, for some reason using the mouse I didnt see any other option in the dropdown accept for "ALL". so I selected ALL and did a next. The setup kicked in and I got different screens showing status of install. But on the final screen it got stuck at 6% and stayed like that for well over 6 hours...I didnt touch the install as the instruction clearly say not to disconnect or stop the exe. But after 6 hours I realized that something is wrong and i killed the Device Software Update Utility.exe file.
5.
I did a soft reset on the phone and to my surprise after a while it loaded WM6....but that was it. Has the install failed in between the WM6 on the phone was totally screwed up...nothing worked properly. I coudnt even get ActiveSync to recogonise my device or connect to it.
6.
I tried the whole sequence mentioned in step 4 again but no luck now Device Software Update Utility.exe would error out I assume it could be because of the BL version 1.0.5. So I thought let downgrade and install the older BL version....but with no active sync i coudnt downgrade the device.
7.
Then i read somewhere SD card boot method to copy the EBOOT0908_MNT_1.00.05.nbf from the SP34074 and rename to eboot.nbo. This didnt work either, am not sure if I renamed the file correctly to .nbo(Orange) or .nb0(zero). Well I dont know whats correct eboot.nbo or eboot.nb0. But since this step didnt work. I was really upset as I felt I was stuck...then GOD had mercy on me and I did something which simply worked ...
8.
I took my mini SD card out connected to my Laptop in the SD card slot with the SD adapter. Did a quickformat to clean it up...if you have data its a good idea to back up the SD card in a seperate folder.
9.
Now I had a clean SD card with no files I downloaded the 1.0.5a (for 68x8) for miniSD. I copied the diskimg.nb0, size : 64,000 KB to the SD card root folder.
10.
Since I was trying the SD card method, I connected the mobile to AC power instead of the PC just to make sure I had enough power for install.
11.
I popped the SD card back into the phone. Removed the phone battery. Then entered into the Bootloader mode (refer to step 3 for getting into BL mode). Well nothing seemed to be happening...but I decided to stay on the BL mode .... to my surprise after 10-15 min i got a message asking my reset and goto factory mode. I wasnt sure if it was asking me to do something or was just a message. While I was wondering...the phone restarted automatically and it loaded WM6 ..asked me to do the tap thing to configure like the initial factory setup .. after all this I poped my SIM inside. Connected the phone to my PC. Active Sync finally recognized my device and synched everthing. Now everything WORKS!!! Though there are some issues like the camera flash doesnt come on.. etc but more or less everything seems to work. I havent tried other applications like email SMS wifi bluetooth etc.. I will post soon my experience weather all main applications work without a glitch...but am so happy my patience paid off..
Thanks to nhocbanme for WM6 version for HP ipqa rw6828, my biggest mistake was not to properly follow steps listed by nhocbanme. For people trying to install WM6 on HP ipaq rw6828....please please use the SD card method...it works and takes less then 30 minutes...you can follow my steps 8,9,10,11 to have a trouble free setup.
Good luck
Amit Reddy
Hi... my bootloader is dead any I cannot locate the fin out to flash my ipaq rw6828... please tell me where exactly are the pin out for rw6828
Thanks you.
Hi WilliamSun,
if you can go to boot loader it mean you can repair your device. You should download WM5/WM6/WM6.1 ROM that design to flash via mini SD. you can download it from nhocbanme's or hellowordl1's thread, and flash your device again.
Good Luck.
HELP
my device is HP Ipaq rw6828.... i have this problems twice, but ican solve it, now i had a same problem.... now i can't resolve it....
now my device still (dead) only LED indicator when i charge it...... i use anything method, but it's not work.... except JTAG, cz i can't use this method.... please, any other way except JTAG mode????????? many big thanks.................. if u have an opinion, email me, [email protected]
in this case i cant solve my problem
downgrade with SP34074 from PC (like intruction on screen PC)
1. run SP34074 from PC
2. remove battrey from device for sec, and put back to device
3. connect the device via USB, n make sure the PC is respon that
4. follow the instruction in screen
its work for me
please tell me am i flashed my jamin the right way.first i press camera and reset button to enter bootloader mode then i connect usb and then start g3 rom upgrade utility same in a folder contain nk.nbf file and wait till 100%. then hardreset all is done. i did all that and my jamin is working file with new windows. is that way right. thanks all .sorry for my bad english
fast666 said:
please tell me am i flashed my jamin the right way.first i press camera and reset button to enter bootloader mode then i connect usb and then start g3 rom upgrade utility same in a folder contain nk.nbf file and wait till 100%. then hardreset all is done. i did all that and my jamin is working file with new windows. is that way right. thanks all .sorry for my bad english
Click to expand...
Click to collapse
If your Prophet is working with the new ROM, it appearrantly succeeded. No need to worry....
Keep in mind that there are hunderds of postings each day on this forum. Please don't start new threads if there isn't any real need for it. That way this crowded forum will stay at least a bit readable... THANKS!
Take a look....
Hello , i've an Orange SPV M3100 HTC and when i've tried to upload the ITA rom near the 81% of uploading the upload have a self crash !!! now i can'nt do nothing.... no hardreset or something !!! When i try to start i can see on display only The red-green-blu-white colours with derscribe : HERM100 IPL-1.01 !!! Please , help me for a new life for my Baby !!!
first on pc go to activesync settings and untick "allow usb connection". Connect to pc and run the install for the original rom (reboot into bootloader BEFORE connecting by holding power,ok button above the flywheel and reset with stylus, hold all buttons in to go to the tricolour screen. I know you're there already but this is now officially bootloader not a f***ed up boot). Theres a chance you will be able to fix it this way. No guarantees.....
Afterwards install Hard SPL on your "baby" so you increase your chance of recovery.
Hi, Thanks for your help ! I've tried but activesync do'nt show nothing . HardSPL cannot see nothing... the only thing i can read in the white stream of "baby" is the scribe change from serial to usb when i connect it to the pc .... Any idea ???
Install the Shipped Stock rom... It WON'T be picked up by activesync but that doesn't matter. Its registering that there is a usb connection so install the shipped stock rom.
DO NOT INSTALL ANOTHER ROM AS THIS MAY PERMANENTLY BRICK YOUR PHONE....
Thanks Mentore , i've a little problem more because i have'nt the original rom....Do you know where i can download it ? Migthy TTTT
hi, i've find it! ( I suppose...) >>>> Official Orange SPV M3100 AKU 3.3 update . It's a full rom official by Orange. I try now and i'll tell you if i kill me...
nothing............the program can't find via usb the baby......arghh
did you go to bootloader before trying - hold power, OK button above flywheel and reset with stylus, hpld all buttons in until it ets to bootloader ?
yes, before when i put the battery it's off, when you put in the battery is off , when you make a hard reset it's start in bootloader red-blu-green ecc. no usb connection display say " serial " , when in usb connection display say "USB" but nothing can find the "baby" in the pc-usb.....
one of probably solution i think is :WM5torage for find in usb , windows mobile 5-6 for read WM5torage and try to load original Orange rom . But i have'nt any 5 or 6...
Hold down the buttons I said on my last 2 posts to go to bootloader. Just resetting means you have a screwed up reset not bootloader reset...
Yhaooooooooooo!!! i've connect to a vista notebook and all black but with right red led on. After i've connected it to my xp desk and autoreboot the old rom.... mistery .....ghost..... bah, now is ok. Thanks overall , see next one. Ciao from Italy.
Cool, Glad you fixed it.
Guys I was updating my Old Gene to vanilamanila
but suddenly error 270 occured and my device reset itself and didnt opened anymore.
how can I fix it???
try to upgrade your SPL
hey its by KRAZY ABOUT TECHNOLOGY {senior member XDA} you can find the whole thread
The Step By Step Guide
The Step By Step Guide
CAUTION: DO NOT UPDATE ROM OF A PHONE THAT IS SIM LOCKED. THE RESULTS ARE UNKNOWN BUT MOST OF THE TIMES IT PREVENTS YOU FROM USING THE PHONE ANY FURTHUR!!
If you like to backup your existing rom first, follow this guide by Ankit360 to do it : http://forum.xda-developers.com/show...8&postcount=20
Step 1: Download the Tools
-------------------------------
Download the tools zip file from here:
http://www.4shared.com/file/81084740...ing_Tools.html
Its a self extracting file, just start it and give a path and it will unzip all the files in your chosen folder. Inside the extracted folder you will find these things:
1. SPL Updater : Inside it there are 2 folders, Olipro and Orefkov. These contain the two SPL patchers that we need to use.
2. ROM Update Utility : This contains the ROM update utility we will need to flash a ROM. Unzip it into a folder.
3. USBDriver4ActiveSyncVista : This contains a special driver for Windows Mobile Device Center in Vista that you need to use to successfully update your ROM. Unzip it in a folder too.
4. Download a ROM appropriate for your device: Which one is appropriate, you'll only know after updating your SPL. So do this step after that. But in any case, here is a link to a good ROM, created by me, which is available for both new and old gene:
Sumit's Pro Users ROM (WM 6.1, for new and old gene)
http://forum.xda-developers.com/showthread.php?t=467796
Step 2: Preparing your phone
--------------------------------
1. Copy the file gene_hspl.exe from the SPL Updater\Olipro folder that you got in step 1 to the phone memory.
2. First, on your phone, Go to Start > Settings > Connections > USB to PC. Here, uncheck the checkbox : enable advance nerwork functionality. Click OK. Disconnect and Reconnect the USB cable to your pc.
Step 3: Prepare your Computer
--------------------------------
XP Users
----------
There is not much you need to do. Just open task manager and kill the Active Sync executable from the processes tab. Its named as wcescomm.exe.
Vista Users
-------------
You need to take these steps :
1. Go to desktop, right click Computer, and select Manage. Go to Device Manager. Now under the section Mobile Devices, Double Click : Smartphone USB Sync.
2. On the Drivers tab, click "Update Driver..." button. On next screen click : "Browse my computer for driver software".
3. Click : "Let me pick from a list of device drivers on my computers". Click "Have Disk.." on next screen. Click "Browse..." and go to the folder extracted in step 1. There, go to USBDriverforActiveSyncVista folder. Here select the file "wceusbsh.inf" and click OK.
4. Click Next and finish the wizard.
Step 4: Use the Olipro method first.
-----------------------------------------
Open File manager on your phone. Go to the location on phone memory where you saved gene_hspl.exe. Tap on it to run it. Your phone will restart after a short pause.
Now there are two chances :
a) If its done alright, you'll see SPL 1.10.Olip on your boot screen and your phone will boot just fine. And it confirms that you have an old gene. You do not need to do Step5. Proceed to Step 6.
b) If it doesn't boots, and only green and red keys blink, Don't worry. Your phone is bricked but you'll get it back using orefkov's method in a minute. Proceed to next step. And this confirms that you have a new gene.
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
Step 7 : Set your PC and Phone back to normal
------------------------------------------------
This step is only needed in case you are using Vista.
The driver we updated in Vista will not work for normal active sync operation. So you'll need to set it back to the original version. There are two ways to do that. Either, uninstall and reinstall the Windows Mobile Device Center Or Follow the same procedure gicen in Step 3 but instead on clicking the "Have Disk button", choose the driver from the list already given.
The driver that you need to install can be identified by have a newer version given in front of its name. Also, the newer driver's name includes "Microsoft Corporation" while the older one has only "Microsoft".
You can Put back your SD card now.
On your phone, again go to the Start > Settings > Connections > USB and check the checkbox there and click OK.
That's it! You are Done.
__________________
HTC P3400i (New GENE)
@rockyyyrulz
the link you provided is for trinity not for gene.cant do such a thing.
@Beco35
try to tell us exactly what the device show and try this
remove the battery and press the power button for a while
then put back the battery and press and hold down the camera key and in the same time press the power (without holding down) if you got a screen with three colors then you will be having a very good chance to recover your gene.
try it and tell what happened.
error 270
Upgrade error number 270 means that the bootloader is not correct for the rom you are trying to flash
sorry
my apology
Beco35 said:
Guys I was updating my Old Gene to vanilamanila
but suddenly error 270 occured and my device reset itself and didnt opened anymore.
how can I fix it???
Click to expand...
Click to collapse
Before starting a thread everyone has to go through all the existing threads on the related topic.Many threads carrying the same problem that you are facing.
Read all these and as rockkyy suggested read gene upgrading step by step guide by sumit.Gud Luck
get it here
hi
look at the bottom of my signature and clik on it it will take u to sumits stiky
save it on ur comp it also has all req tools do it word for word and success will be urs
good luck
rakesh_4utoo said:
Before starting a thread everyone has to go through all the existing threads on the related topic.Many threads carrying the same problem that you are facing.
Read all these and as rockkyy suggested read gene upgrading step by step guide by sumit.Gud Luck
Click to expand...
Click to collapse
@rockyyy : For heavens sake, do not post full tut in threads like these man, its a waste of space and bandwidth and its annoying to scroll though it everytime. A link to the original post would have done that easily. In case you aren't aware, every post has a number in its top right corner like this one has #8. This number is also a permanent link or permalink to that post and it can be used to refer to it. Just right click on the number and copy the link address.
Thx for ur helps rocky rakesh mido haree
but the problem is my Gene cannot connect to the pc. screen is black and by the time I connect with USB activesync not strarting and my pc not see my device... Gene cannot open, Usb is not working and the link u have designated in first reply doesnt work (4shared....)
wat to do - take to service
hi
im not a techi and it looks like u have to take it to the service and chek with them
good luck
Beco35 said:
Thx for ur helps rocky rakesh mido haree
but the problem is my Gene cannot connect to the pc. screen is black and by the time I connect with USB activesync not strarting and my pc not see my device... Gene cannot open, Usb is not working and the link u have designated in first reply doesnt work (4shared....)
Click to expand...
Click to collapse
ok thx for ur great efforts
try this o got the same problem
hi
i got the same problem today ie phone not turning on
thats wat happened to me wen i flashed a rom i got it up and running this is wat i did try it
1. take battery out and hold camera button and powebutton for some time
2.put battery back
3. press power and camera if u get tricolor flash rom( this did not work for me)
2.Use stylus rest keep pressing camera button while doing this
i got try color i flashed new ROM i did this in the last 1hr
i hope this will help u and also save ur Phone
if u cant get wat i say clik on the link i think it is explained better
goodluck
http://forum.xda-developers.com/showpost.php?p=3637172&postcount=8
Beco35 said:
Guys I was updating my Old Gene to vanilamanila
but suddenly error 270 occured and my device reset itself and didnt opened anymore.
how can I fix it???
Click to expand...
Click to collapse
u r vonderfull sweethrt )) now my gene connected to pc ) I finally saw the three color screen... I ll follow the steps which u posted in 1st reply... many many thx...
I hope I d update my gene..
On The Three colo0r screen
ONBL 1.07.0000
SPL 1.07.Oref
is written..
what s the meaning ?
@Beco
you are good to go now
go and flash any old rom and you will get it back running
good luck
mido0109850352 said:
@Beco
you are good to go now
go and flash any old rom and you will get it back running
good luck
Click to expand...
Click to collapse
I downloaded the original ROM from HTC and flashed but after the installation GENE Did not started. returned to brick. I ll try again and inform u
Don't flash the official ROM. It Contains IPL and SPL. Hence your device is bricked again.
which one you downloaded
tell us as soon as possible cause you might have bricked it
Yupppiiiiiiii.....
Yess Yess Yesss... I did it ))
Rescued my gene )))
many many thx to alll supporters especially to Haree and Mido
th u very very much for ur helps and patience...
I downloaded this one Ramersonw...
ftp://213.194.123.227/Cep Bilgisayari - Pocket PC/HTC/Gene 3400/
first it bricked but after 2nd flash everythng good )
good so everything is good now nice
try the new wm6.5 for old gene not new gene it is very good
give it a shot and dont worry it wont brick yours.
goodluck
Hello frend's i am new in this forum ,
i did a big mistake first i rooted my xperia 10mini and use 2.2 rom then i try to recover my phone in original version 2.1 . When i try and restart my phone and press back button it's goes to recovery mode not automatically recovered so i delete from c drive recovery.tar file and two more file now my phone is stuck on lobo of android doll. What to do i son't know please help me my phone is going to die.
Easy get seus and reflash your phone stock or boot into recovery ,,, using charging phone power on phone unplug charger use a back up ,,if you can't start again rember to do back ups
saurabh12311 said:
Hello frend's i am new in this forum ,
i did a big mistake first i rooted my xperia 10mini and use 2.2 rom then i try to recover my phone in original version 2.1 . When i try and restart my phone and press back button it's goes to recovery mode not automatically recovered so i delete from c drive recovery.tar file and two more file now my phone is stuck on lobo of android doll. What to do i son't know please help me my phone is going to die.
Click to expand...
Click to collapse
thanks again slade 87 ,sent from x10 mini pro cm7 15.0 ,,,,also on you tube (totalchris08) xbox360 (kormatoes ne5 ) ps3 (langtoes) ask my anything , I COULD KNOW THE ANSER OR I MIGHT NOT ,
still hanging in death rope
thanks 4 reply but my phone is even not going to switch off . again & again it'll starts and cyanogen logo is came the phone starts and this type msg showing which is stick until phone start again SORRY THE APPLICATION LAUNCH PRO()
PROCESS ANDROID.PROCESS.ACORE)HAS STOPPED UNXPECTALY.PLEASE TRY AGAIN
PLEASE HELP ME BRO IF ANY OTHER PROCESS IS THERE TO RECOVER MY PHONE PLEASE TELL ME IN DETAIL IF U HAVE ANY VIDEO THEN SEND ME A LINK PLZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ
Ooooooo you have a mini ,,,not pro ok you got the rong rom ok there is a hard reset. http://www.youtube.com/watch?v=2cvExle8S4o&feature=youtube_gdata_player
saurabh12311 said:
thanks 4 reply but my phone is even not going to switch off . again & again it'll starts and cyanogen logo is came the phone starts and this type msg showing which is stick until phone start again SORRY THE APPLICATION LAUNCH PRO()
PROCESS ANDROID.PROCESS.ACORE)HAS STOPPED UNXPECTALY.PLEASE TRY AGAIN
PLEASE HELP ME BRO IF ANY OTHER PROCESS IS THERE TO RECOVER MY PHONE PLEASE TELL ME IN DETAIL IF U HAVE ANY VIDEO THEN SEND ME A LINK PLZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ
Click to expand...
Click to collapse
,sent from x10 mini pro cm7 15.0 ,,,,also on you tube (totalchris08) xbox360 (kormatoes ne5 )
I DID ALL SUCH THINGS BUT NOTHING GO RIGHT 4 ME IS THERE ANY OTHER SOLUTION ,I READ ABOUT FLASHTOOL IN FORUM CAN U PLZ EXPLAIN IF BY THIS I CAN DO SOMTHING BUT PLZ EXPLAIN IN DETAIL
I had the same issue it restarts by itself n go into looping, remove the battery place it back, connect ur phone to SEUS by holding back button and plugging the USB
xperia mini10
in mini 10 battery is not removable & my basic operating files are deleted show when there is no operating file how it'll starts a home screen thats y i m asking u and other frend's is there any other method to re install operating 2.1 or any thing to start my phone again so i can do after that any thins otherwise nothing is worth 4 me saddddddddddddd
If your recovery (xrecovery or clockwordmod) works fine, what about removing your SD and plug it to a PC in order to copy a 2.1 ROM and then install it through recovery?
please ell me
plz tell me in which folder i'll put that files , basically allready tried all even my update zip is also there how to do and wht 2 do plz explain is there any method to recover from sdcard or through any other software
is there xrecovery file work from pc do u have exe file so plz sen me
[email protected]
is there any method to format c drive of phone bcs when ever i'm trying
through pc companion it'll tell in last stage to use usb storage but y phone is not starting so how could i do this nothing work 4 me plzzzzzzzzzzz any one give me solution I'm very depress my phone is even not going to switch off it'll starts again & again until battery drained
i deleted my three files from c/: x recovery.tar, con. & busy box
saurabh12311 said:
when ever i'm trying through pc companion it'll tell in last stage to use usb storage but y phone is not starting
Click to expand...
Click to collapse
That's weird because 7 hours after i brought my X10 mini pro i already bricked it , so i fire up SE PC companion and i followed the instruction to _repair_ the phone and no access to USB storage was needed that i remember.
It simply downloads and flash to your phone.
Unfortunately i'm still a newbie so i suppose and i haven't all the right answers
Keep trying with SE repairing and good luck with that!
Oops sorry, click the reset button, dnt turn your cell on, press the back button plug in the usb u'll see the green light!
if works then tell me...
ps: u said u deleted ur xrecovery.tar nd cant boot into recovery, how the hell u think u'll be able to install zip from sdcard??? Only way u have is SEUS or try using bin4ry's flashtool, download mini's1.1 rom....
Oops sorry, click the reset button, dnt turn your cell on, press the back button plug in the usb u'll see the green light!
if works then tell me...
ps: u said u deleted ur xrecovery.tar nd cant boot into recovery, how the hell u think u'll be able to install zip from sdcard??? Only way u have is SEUS or try using bin4ry's flashtool, download mini's1.1 rom....
thanks dear but finally my phone is ded I sent my phone to customer center but after checking they told me no hope phone will not recoverd..........
half knowledge is always dangerous is true for me I lost my money
There is no way that seus could not fix your phone and even if it couldnt se has a duty to repair it free of charge in the first 12 months !
Sent from my U20i using XDA Premium App
SEUS wont fail!
galvic said:
SEUS wont fail!
Click to expand...
Click to collapse
Quote that and DON'T THROW IT AWAY. USE flashtool. I got mine bricked and that was a great solution.
If you still have it i'm gonna show you a guide to flashtool