Hello,
I installed a ROM, its been a long time ago, so I don't remember which one it was... but I've noticed that my phone which used to show G on the top is now showing H at the same place.
My question is, is it just displaying H and running on 3G, or did the ROM disable my 3g, and put me on HSDPA network?
To make some things clear..
G = GPRS (normally when 3G or HSDPA is not available)
3G = UMTS (if available from operator)
H = HSDPA (upgrade of UMTS)
If HSDPA is available and you are connected to UMTS (this is setup first, normally) it will switch to HSDPA modus and will display a H.
The G and the 3G are always shown if covered by the place/network you are on. The H only shows up if the network/coverage of hsdpa is good enough AND your connected..
Atleast, that is the case here.
thanks for clearing that up...
excuse my inferior knowledge, but any idea why it was showing 3G before I installed the ROM, and it shows HSDPA after I installed it?
magicman0 said:
thanks for clearing that up...
excuse my inferior knowledge, but any idea why it was showing 3G before I installed the ROM, and it shows HSDPA after I installed it?
Click to expand...
Click to collapse
Well if your on AT&T their roms have HSDPA locked for no apparent reason but chefs here tend to enable it for you to give you a significant speed boost in up/downloading.
Related
well through testing almost all of the roms here in this section i have found out that every rom does have 3g but if you select HSDPA/HSUPA you will lose your 3G connection and can only have it again if you disable HSDPA/HSUPA. This seems very odd because the hermes and kaiser would switch between the two depending on which one had the stronger connection. i welcome others to test this as i think it is interesting and should be looked into.
HackMimic said:
well through testing almost all of the roms here in this section i have found out that every rom does have 3g but if you select HSDPA/HSUPA you will lose your 3G connection and can only have it again if you disable HSDPA/HSUPA. This seems very odd because the hermes and kaiser would switch between the two depending on which one had the stronger connection. i welcome others to test this as i think it is interesting and should be looked into.
Click to expand...
Click to collapse
Hmmm Curious..
I am currently running RomeOS 1.21 and am about to update to 1.51.
mine switches no problem between the two.
If i can't get a HSDPA signal then it auto switches to 3G..
will see if the new rom changes anything.
Dean
let me know because i have been observing and have only seen it auto change from H to E or G whichs sucks when it use to go from H to 3G. travel the entire bay area for my job and both phones side by side with me act different. so wierd.
HackMimic said:
let me know because i have been observing and have only seen it auto change from H to E or G whichs sucks when it use to go from H to 3G. travel the entire bay area for my job and both phones side by side with me act different. so wierd.
Click to expand...
Click to collapse
I Thought H was the same as 3g. Isn't Att's 3G network run on HSDPA?
HackMimic said:
well through testing almost all of the roms here in this section i have found out that every rom does have 3g but if you select HSDPA/HSUPA you will lose your 3G connection and can only have it again if you disable HSDPA/HSUPA. This seems very odd because the hermes and kaiser would switch between the two depending on which one had the stronger connection. i welcome others to test this as i think it is interesting and should be looked into.
Click to expand...
Click to collapse
HSDPA/HSUPS is 3G. If you are referring to WCDMA vs HSPA there would not be a stronger connection for either because they are on the same frequency.
Fact is on the Hermes/Kaiser the HSPA was downstream only (HSDPA) , on the raph its has bi-directional HSPA (HSDPA and HSUPA) therefor the towers you are broadcasting to with the device will have HSPA mode on continuously as apposed to only when you are receiving from them since the device is receiving and transmitting using HSPA.....which is why the HSDPA mode "H" symbol only appeared during data transfer on the older devices, there was normally a short delay (when using the device as a modem for example) before the "H" appeared and the data began coming in.
Notice how you need to reboot if you choose to deactive HSPA alltogether? The radio stack probably needs to start a new session on the network to change from HSPA back to UMTS only. Indeed when you set standard 3G mode you should get the "3G" symbol rather than "H".
The service rep at ATT told me the other day that HSDPA is actually different then 3G. THe HSDPA is typically meant for the Laptop Connect cards. Since the inception of the iPhone on 3G if you haven't noticed your speeds have dropped significantly.
How true is this I don't know...but when I am using a ROM like RRE that has HSDPA my speeds are much faster then with 3G.
ryncppr said:
The service rep at ATT told me the other day that HSDPA is actually different then 3G. THe HSDPA is typically meant for the Laptop Connect cards. Since the inception of the iPhone on 3G if you haven't noticed your speeds have dropped significantly.
How true is this I don't know...but when I am using a ROM like RRE that has HSDPA my speeds are much faster then with 3G.
Click to expand...
Click to collapse
HSPA (3.5G) is just another coding method, it still uses the 3G frequencies as with UMTS (aka normal 3G). The theoretical bandwidth due to the more complex an efficient coding method means you can get ALOT more bandwidth down the same frequency than with UMTS. So technically UMTS and HSPA can both be encompassed into the "3G" terminology although they use different coding techniques, the video calling and voice stuff are handled identically afaik, data transmission is where they differ.
This kind of improvement can be seen in the 2G technologies with GSM/GPRS/EDGE.
HSDPA is a "higher speed" data connection than 3G... but its still a "3G" frequency data connection. So on-the-face-of-it, they are one and same, just one is faster than the other.
thank you so much. i am a very visual and analytical person. love to compare behavour. glad i got a real answer about this as i have been reading for days on this and it seems kind of cloudy with the fuze on information. thank you again for the replys.
Wow, there's quite a bit of information, some conflicting, about the various 3G-related terminologies here. So I might as well add my take on it all
Let's compare 2G terminologies to 3G ones, as that should make it easier for some to understand.
GSM - the very basic 2G standard
UMTS - the very basic 3G standard
GPRS - upgraded GSM to packet switching - faster data access - dubbed 2.5G
HSDPA - upgraded UMTS to faster downlink speeds - dubbed 3.5G
EDGE - upgraded GPRS to faster data access - dubbed 2.75G
HSUPA - upgraded UMTS to faster uplink speeds - dubbed 3.75G (occasionally)
Finally, HSPA is simply a term encompassing HSDPA and HSUPA.
I hope this helps more than it hurts
Trancecoder said:
GSM - the very basic 2G standard
UMTS - the very basic 3G standard
GPRS - upgraded GSM to packet switching - faster data access - dubbed 2.5G
HSDPA - upgraded UMTS to faster downlink speeds - dubbed 3.5G
EDGE - upgraded GPRS to faster data access - dubbed 2.75G
HSUPA - upgraded UMTS to faster uplink speeds - dubbed 3.75G (occasionally)
Click to expand...
Click to collapse
There i fixed it for you
shotta35 said:
There i fixed it for you
Click to expand...
Click to collapse
WCDMA is the air interface for UMTS as
TDMA is the air interface for GSM.
At the same time, GSM is used to describe a phone system that uses GSM/TDMA and UMTS/WCDMA versus the CDMA phone system used by Sprint/Verizon/Qualcomm.
Confused yet?
NuShrike said:
WCDMA is the air interface for UMTS as
TDMA is the air interface for GSM.
At the same time, GSM is used to describe a phone system that uses GSM/TDMA and UMTS/WCDMA versus the CDMA phone system used by Sprint/Verizon/Qualcomm.
Confused yet?
Click to expand...
Click to collapse
PLEAAAASEEE can we go into how OFDM and QPSK work?? i want to see some heads explode...scanners style.
NuShrike said:
WCDMA is the air interface for UMTS as
TDMA is the air interface for GSM.
At the same time, GSM is used to describe a phone system that uses GSM/TDMA and UMTS/WCDMA versus the CDMA phone system used by Sprint/Verizon/Qualcomm.
Confused yet?
Click to expand...
Click to collapse
LOL, newbs reading this will and should be confused. I only edited it to make his comparisons between GSM and UMTS which is should be, not GSM and WCDMA which aren't in the same "group"
shotta35 said:
LOL, newbs reading this will and should be confused. I only edited it to make his comparisons between GSM and UMTS which is should be, not GSM and WCDMA which aren't in the same "group"
Click to expand...
Click to collapse
*head explode*
what are decent speeds for HSPA connections?
shotta35 said:
There i fixed it for you
Click to expand...
Click to collapse
Thanks. I really shouldn't post anything when it's late, especially when my head feels twice its size due to a particularly annoying cold
NuShrike and Mr. Vanx has explained it.
These jargons always confusing for us, laymans. Easiest term is i think CDMA (2000,1X, EVDO) is used almost exclusively in US, while GSM and WCDMA (UMTS) is in almost everywhere else of the world (around 3.5 billon users as of now - open www.gsmworld.com). Except Japan, they have their own customized system.
Reasons of difference? Matter of choice, more like when you decide using VHS instead of BetaMax. I think part of the reason why US choose CDMA instead of GSM you may ask Qualcomm's technical people, as they hold majority of the copyrights and licenses in CDMA technology. Not only in driverless chipsets... LoL.
Actually, we in Indonesia also adopt CDMA in smaller and narrower market. But the gov limit them to be Fixed Wireless. Now, what does the jargon: Fixed Wireless means?? Another head exploded... LoL =D
3G icon shows when the phone's sitting idle, H shows when data's being transferred.
My phone shows H all the time now because this market has moved on from UMTS + HSPDA to a HSPA market now. This is ONLY as a result of using the non-AT&T ROM, if you use that it will say 3G because AT&T has disabled it (the icon, not speeds) to cause less confusion.
As for what's typical HSPA speeds? Well on the AT&T network i've seen as high as 2Mbps (on a 3.6Mbps HSPA network) but there are places in Europe that are deploying 7.2Mbps and in Australia they are launching 21Mbps!!!
Hi
Our O1 is HSDPA 7.2 Mbps acroding to spec sheets but in the settings it shows either GSM or WCDMA. There is no HSDPA.
Is HSDPA included in the GSM settings?
I am getting very low speeds even when it says 3G in the notifications bar so was just wondering.
WCDMA deployments are usually marketed as UMTS.
UMTS networks in many countries have been or are in the process of being upgraded with High Speed Downlink Packet Access (HSDPA), sometimes known as 3.5G.
So the answer to your question is: HSDPA is included in WCDMA settings. Or properly said, it is a feature of the WCDMA connection mode. Your phone supports it. If you get low speeds, then your operator doesn't offer this service in your area. Or at all.
If you have never seen an "H" in your status bar, only "G" or "3G", that't the answer: no such service in your area from your mobile operator.
I actually see H and 3G most of the time with it goin to E(EDGE) or G(GPRS) very rarely.
I was just wondering why it wasn't given in the settings.
And the speeds remain poor. Even at nights, assuming less traffic/users, the speeds rarely rise above 40 KBps. I am not looking for 3.6 Mbps or 7.2 Mbps but atleast speeds in the range of 1Mbps(128KBps) should be there.
Anyway, i guess its my operator that sucks!
Now that number portability has been rolled out here in India its time to switch operators!
Thanks for the reply. Upped that meter a little for ya!
kewlsid05 said:
I was just wondering why it wasn't given in the settings.
Click to expand...
Click to collapse
The reason why you don't see HSDPA as an option in your menu is because the WCDMA connection will automatically work at its best: HSDPA if available or 3G otherwise. Low speed even if your phone is connected using HSDPA is definitely your operator's fault.
Glad I was able to shed some light on this matter and thanks for the appreciation.
Hi
I have the Galaxy S2, when I turn on the use packet data and data roaming in the mobile network settings, an icon H+ starts flashing on the top of the display with two little arrows.
1. What does it mean? Is the phone downloading data from the cellular network?
2. What is: packet data and data roaming? What's the difference between the two?
Many Thanks.
Hi,
The icon itself means that you are connected to the data network of your cellular provider.
The icon can look like one of the following:
G - 2nd (or 2.5) generation connection
3G - 3rd generation coonection
H - 3.5 generation connection
H+ - 4th generation connection. This does not mean your provider actually support 4th generation data rates.
When the little arrows are gray - No data is being sent/received. When they are colored it means your phone is sending/receiving data.
Roaming means that you are connected to a "foreign" cellular provider (not the one you are paying to).
Data roaming means that you allow your phone to use data connection when you are roaming.
Using data connection while roaming is extremely expensive and it is highly recommended not to do so.
Hope I got it all covered for you
Data conection
Thank you for clearing this for me.
interline said:
Hi
I have the Galaxy S2, when I turn on the use packet data and data roaming in the mobile network settings, an icon H+ starts flashing on the top of the display with two little arrows.
1. What does it mean? Is the phone downloading data from the cellular network?
2. What is: packet data and data roaming? What's the difference between the two?
Many Thanks.
Click to expand...
Click to collapse
well I did my digging and got some more accurate figures in addition to the above
G is GPRS 86kbps
E is EDGE 236kbps
3G is UMTS 386kbps
H is HSDPA 3.2Mbps
H+ is HSPA 7.2Mbps
H+ is too for HSPA+ for 14.4Mbps or 21.1Mbps
(noteH and H+ are the so called 3.5G
and the new comer:
4G ( LTE technology) is 100-300 Mbps ( the iphone5 is said to be on 100Mbps)
some phones don't show H or H+ , they just show 3G for UMTS, HSDPA, HSPA, HSPA+
only G or E means it's on 2G, - that is you are not in 3G coverage
PS on my Vodafone, using speedtest.net app i get on H+ 7.12 Mbps... ( aka 0.89 MB/s)
Period
Slackflash said:
well I did my digging and got some more accurate figures in addition to the above
G is GPRS 86kbps
E is EDGE 236kbps
3G is UMTS 386kbps
H is HSDPA 3.2Mbps
H+ is HSPA 7.2Mbps
H+ is too for HSPA+ for 14.4Mbps or 21.1Mbps
(noteH and H+ are the so called 3.5G
and the new comer:
4G ( LTE technology) is 100-300 Mbps ( the iphone5 is said to be on 100Mbps)
some phones don't show H or H+ , they just show 3G for UMTS, HSDPA, HSPA, HSPA+
only G or E means it's on 2G, - that is you are not in 3G coverage
PS on my Vodafone, using speedtest.net app i get on H+ 7.12 Mbps... ( aka 0.89 MB/s)
Period
Click to expand...
Click to collapse
Is there a different icon for DC-HSDPA, or is it 'lumped' into H+?
The standard should theoretically allow up to 84Mbps with MIMO, but my phone only supports up to 42Mbps.
KPN in NL has it rolled out, but I've never been able to confirm if I'm on DC-HSDPA. Using Network Signal Info android app, the fastest I've connected is HSPA+ at 21.6Mbps.
hello seniors, please someone help my phone e120l network not connect to "H" only G/3G connected..how to fix this problem? im already updated to 4.1.2 jelly bean rooted+cwm recovery..
It depends on your area/city/carrier
Sent from...this is not even my S2
hamba9551 said:
hello seniors, please someone help my phone e120l network not connect to "H" only G/3G connected..how to fix this problem? im already updated to 4.1.2 jelly bean rooted+cwm recovery..
Click to expand...
Click to collapse
Did you connect with stock installed firmware to H or not?
Before this im using rooted rom from Vietnam dev.. Its enabled H on my status bar.. But after a month using thus phone there is no H available.. After that i reflash stock rom then 3G came out from status bar.. No H anymore.. Download speed also decreased via 3G..
Sent from my LG-E975 using xda premium
change your modem.
Sent from...this is not even my S2
Hi, I have my optimus one for half a year. After i upgraded the software to 2.3.3 the 3g doesn`t worked(there is just a H) What can I do to solve this problem?
PS: The update has come with Vodafone Romania and i am on Orange Romania.
Check if the /system/etc/apns-conf.xml contains entries for Orange Romania. If not, download CyanogenMod apns-conf.xml
Otherwise try to flash the old baseband.
Is data working, but you're afraid you aren't getting 3G speeds? This is from the CyanogenMod FAQ:
Why do I sometimes see an 'H' for the network mode?
H = HSDPA mode (fastest)
3G = UMTS mode
E = EDGE mode
G = GPRS mode (slowest)
NOTE: Almost all 3G devices support HSDPA mode, however most stock firmware only indicates "3G" regardless of whether the device is in HSPDA or UMTS mode. CyanognenMod uses "H" to differentiates between the two modes. Note that HSDPA is not 4G, it is merely an extension of the 3G standard and is therefore only slightly faster than true 3G.
MechanicaIMan said:
Is data working, but you're afraid you aren't getting 3G speeds? This is from the CyanogenMod FAQ:
Why do I sometimes see an 'H' for the network mode?
H = HSDPA mode (fastest)
3G = UMTS mode
E = EDGE mode
G = GPRS mode (slowest)
NOTE: Almost all 3G devices support HSDPA mode, however most stock firmware only indicates "3G" regardless of whether the device is in HSPDA or UMTS mode. CyanognenMod uses "H" to differentiates between the two modes. Note that HSDPA is not 4G, it is merely an extension of the 3G standard and is therefore only slightly faster than true 3G.
Click to expand...
Click to collapse
Are you sure that H is fastest then the 3G? The speed is not so fast as it was with 3g.
sigheteanul said:
Are you sure that H is fastest then the 3G? The speed is not so fast as it was with 3g.
Click to expand...
Click to collapse
All of that info is copied from the CM Wiki FAQ.
But i am on the original software, i made the upgrade when update notification from android 2.2 asked me to upgrade. i don`t have CM
sigheteanul said:
But i am on the original software, i made the upgrade when update notification from android 2.2 asked me to upgrade. i don`t have CM
Click to expand...
Click to collapse
So what? Did you read what I already posted?
"however most stock firmware only indicates '3G' regardless of whether the device is in HSPDA or UMTS mode"
Some stock firmware shows an "H," and some does not. Guess which you have.
Thanks for help. I will try with CM7 to see what is hapenning.
Hi
I just bought this device.
I am a noob, and don't know much.
Under info it says "SGH-T959"
I am under the impression that this is the 3G version (and not the 4G).
Am I right about this?
If I am right, and this is the 3G version, than something weird seems to happen: I just installed CynogenMod ROM and I see the "H" sign when surfing. Now isn't this the HSPA sign for TMobil's 4G speed?
So I am confused
Please help
Thanks!!!
Yes, the phone you have is 3G.
If memory serves, the H stands for HSDPA, which is what TMobile uses for 3G. 2G is shown as an E for EDGE. The stock Samsung ROM shows HSDPA as 3G while most custom ROMs change the 3G to an H. It means the same thing, though HSDPA is more correct.
What they should have done is used 2G for Edge and 3G for HSDPA, or E for Edge and H for HSDPA. But really, I'm just nitpicking now.
Thank you !!!!
I believe 3G = UMTS while 3.5G = HSDPA. Vibrant is actually benefiting from HSDPA, but simply is hardware limited to max data rate of 7.2 Mbits/s.