This is for people who want Cricket to work perfectly, just follow these instructions not skipping a beat and you will be OK from then on! If you are not having problems obviously skip this!
I have updated this thread ONLY to Change a step. Its not a Required Change for current Cricket users however, it may be needed for Phones that have never been on Cricket before. I also re-phrased some things to be more understandable.
This thread is assuming that you already have your phone Unlocked (spc code all zeros) and that you have already contacted Cricket and had the Phone you are programming added to the Account. You might as well tell them you have a Motorola Razor V3C that will ensure there will be no problems obtaining EVDO.
Also ask Cricket for your MSID/MIN number (usually not your Phone Number) we will be needing the MSID/MIN if you dont know it, or if the phone was never on Cricket before.
My HTC Unlock Tools Directory, Read SPC Instructions Readme
My Cricket WAP and Arcsoft new versions or my Cricket Carrier CAB <--If you are installing one of my Cricket CABs dont test it until your PST settings are correct.
This thread is also assuming that you already have a CRICKET PRL file loaded in PST. If you have my ROM flashed than a couple PRL files that you can use are on device memory we will get to that later below.
Important note on PRL files. You must know what kind of Cricket Plan you have. If you have Roaming on your plan you need to use the 5 digit PRL files. If you DO NOT have Roaming on your plan you must use the PRL files that are considered 4 digits or contain a 0 at the beginning. Otherwise *228 will not work and you will not be able to Authenticate. Some report for users with roaming you may have to use PRL 1042 and set your SID to be able to *228. Examples below.
PRL 01013 = Non Roaming
PRL 38515 = Roaming
1. Now first thing you want to do is have a good Cricket CAB or ROM installed. This way when the PST settings are done they can be looked over again, and tested.
2. Now if you are starting from a fresh flash OK, if you are starting from a hard reset OK, we can continue. If you have a ROM installed that is having problems I recommend a hard reset and skip Auto Customizations using stylus when it says you have 3 seconds. If you are confident the ROM you have installed is ready to go then fine. We can continue.
3. Now open your Phone Application and go to options and make sure smart dial is off. Then dial ##778 call button (PST/EPST), now click edit and enter six zeros. In the Main Page change the NAM name to Cricket, and enter the MSID/MIN number (that you obtained from your old Cricket phone or from Cricket themselves) make sure its a 10 digit number thats in your area code BUT IT IS USUALLY NOT your PHONE NUMBER. If it was already fine we can continue, if you dont know it you may of skipped obtaining this from calling Cricket as stated above. Now click view info and goto PRL, now check to make sure you have a CRICKET PRL (1013,1014, 1040, 1050 etc.. there are others) If you dont have one loaded in PST and you are using my ROM then you can click in Update PRL File (click in the blank area under setting) and then click Menu, edit, browse and it should go to main root (my documents). Pick PRL 1050 (You may have to try another PRL for *228 to work in step below). Then click ok, then Menu, then ok, it will ask you if you want to update the items click ok. Let it do its thing and restart. If you already have a CRICKET PRL then skip the update PRL step but still make sure to click menu, then ok and let it restart.
4. Now after the phone restarts open phone application again and dial *228 call button (this will make sure base settings are good so i will not have to explain as much, it will also download the proper local EVDO prl to where you are), it will dial cricket and do its programming thing. Do not interrupt this. Let it do its thing even if it restarts. It should say Update complete or Programming complete (if not then try a different Cricket PRL) Now when you are back in action we can continue.
5. Now open the phone application and dial ##778 call button (PST/EPST), now click edit and enter six zeros. Now click view info and goto AKEY and make sure its blank, nothing there. Now click view info and goto NAM settings, NAM name should be Cricket, Mobile Directory number should be YourTenDigitPhoneNumber, MIN1 should be that other phone number the MSID/MIN that is usually not your phone number, but it should be 7 digits, ex: sevendigitnumber, MIN2 should be just your area code. MSID/MIN should be 10digitMSIDnumber <--again usually not yourphonenumber, This part I only know for USA users MCC should be 310, MNC should be 00 (for other Countries you have to look this up), NMSI should be your MSID/MIN (XX10digitnumber<--usually not your phone number) THE XX'S should be zeros, ex: 007185548692, Now if all these settings in this paragraph didnt need touched assuming you didnt skip any of my steps (which they shouldnt be touched i am just making sure) we can move on.
6. Click view info and goto CDMA settings, we are going to make sure they are set right and change a couple things for Clearer voice transmissions, people will compliment how good your phone sounds even in some cases. EVRC should be set at Disable, Home page should be Voice 13k, the Two below it the Same Voice 13k.
7. Click view info click modem settings, change slot cycle index to 1, This will make the phone ring a little sooner, also get your texts a bit sooner. The other 4 options should be Auto, Auto, Enable, No in Order from top to bottom.
8. Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the password below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
9. Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
10. Click view info and pick MIP Default Profile, Enable profile should be ENABLE, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 68.28.15.12, secondary should be 68.28.31.12, HA shared secret and AAA secret should be cricket <--lowercase, DMU public should be 0, MN Authenticator should be 0.
11. Click view info and pick MIP customer profile 1 and make sure Enable profile is DISABLED. Now do the same with the other 4 profiles (profiles 2-5), make sure that the only profile enabled is MIP Default Profile.
12. Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778 call button (PST/EPST), we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to [email protected], password should be cricket<--lower case, same for PPP user id and Password make them same as HDR.
13. Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both cricket<---lowercase, then click menu OK and let it reset.
Thats it! PST settings are perfect for CRICKET, you have a Local EVDO prl file installed, and you are Authenticated for Data and EVDO, now if you used my ROM just go to internet explorer and goto a real page, and follow instructions but remember to click save password! You can also go back into the Phone Application and turn smart dial back on if you choose.
Thats done, every Custom ROM flash from now on should never affect your PST settings and you should always be Authenticated. I hope this helps everyone.
Ryan Mogul
Good write up for this. I have one big problem. when I try to *228, it fails after just a couple of seconds and says,
“The number of SPC attempts failed 15 times from the network. Handset will free for 1 minute and will then reset.” I read a post that was obscure but said that the SPC should be six 0's Mine is not all zeros. I don't know how to change mine to all zeros if that is the case
Thanks
That is the case, for *228 to program your SPC code needs to be all zero's or all 3's (make it zero's though) just follow My Unlock pack and Instructions, it guides you through changing your SPC to all zeros.
Cheers.
RECOGNIZE
Qpst will not recognize my phone
thanks for the great info. as a note, changing the EVRC setting (#7) to 'Voice 13k' kills my phone connection; i couldn't make or receive calls. everything else seems fine!
About Voice 13k Settings
Read the settings again, maybe you missed something.
Check these four settings, also make sure you have used *228 and let it UPDATE your PRL, don't do it manually afterwards. Then check all of the above settings over again and you should be good. I have researched, tested, and used these settings for a long time.
EVRC should be disabled
Home Page should be Voice 13k
Home Orig should be Voice 13k
Roam Orig should be Voice 13k
Since your phone is digital, it uses a codec to determine how the voice data is compressed into digital. Voice 13k (Qualcomm's Purevoice) is the highest voice rate. EVRC (Enhanced Variable Rate Codec) benefits the carriers because it uses a reduced rate, which means less bits to stream, more calls to go around. Voice 13k is in fact the updated version of EVRC that our Digital phones have the option to select from. Voice 13k should be enabled for optimal voice quality.
Take Care
heres why your *228 doesnt work for you..
This is for the User Vickie that needed a little help.
In order to use *228 for Cricket You need to have a Cricket PRL already loaded on the Device meaning installed from PST. You also need the phones SPC code to be all zero's (000000) Then *228 will work fine. It will then update your settings and DL a new PRL if a better one exists. This is for Cricket. If that works out you can follow my settings over again.
hey ryan i have installed your V1.1 Heavy Cricket rom, works great, thxs a lot
neways i was going trough this and i did every step to the letter, now mine didn't work... so i have to ask you a few questions...
first, once i am done with this, and if i did it correctly, i can now make calls and internet right? (hopefully this is yes...)
ok so assuming the answer to the above is yes, then i have to ask.
On step 3, you say if we have your ROM we can just update the PRL from there and to skip the "update step". by update step i'll assume you meant step 4. but then in step 4 you say "for both people who had to restart and people who didnt" and then you say to dial *228
so do we do that even if we already have your PRL loaded?
or do we never have to dial *228 if we have ur prl file?
also, on the profiles, in the M.IP settings, my phone had "6" profiles by default, should i set it to 5 like yours or what?
ok i got everything working beautifully, thanks for the instructions... it's just that i wasn't supposed to dial *228, and i did
anyways, my internet works, and holy cow i get bursts of 2mbps!
well one last thing i gotta ask is... so my calling doesn't work, so i have to call cricket or something to have them switch it to mine right?
on a sidenote, do you guys actually use IE? isn't there like firefox mobile or something??
PST settings are not the Only thing that matters for Internet(WAP) or for MMS. The ROM you are using also has to be configured properly for Cricket WAP/MMS to work. My ROM does but not everyone uses My ROM.
This thread will get your Phone's 1X and EVDO set up correctly. Which will ensure that if your ROM is configured properly that Calls/Text/WAP/MMS will all work. But this thread is NOT the only thing that matters. Read the end of my TOP post and it tells you what the Thread sets up..
Now for your other questions: In this PST settings thread Step 3 says that if you are using MY ROM and the phone doesnt have a Cricket PRL loaded in PST that my ROM has Cricket PRL's copied on it to Update PST with(after updating PST with Cricket PRL phone will soft reset).
This means that YES you need a Cricket PRL loaded(updated) in PST before dialing *228 and then it will restart and then on with the rest of the settings. Dialing *228 gets a local(to your AREA) EVDO PRL loaded in PST(which is downloaded from Cricket Realtime) and sets up base PST settings so that this thread is easier. It explains that in the TOP post at the TOP..
ok in the version of your ROM that i installed, which would be the V1.1 Heavy, it says in that post this:
"Messaging and Connections settings: <--Please do not mess with these as they are fine tuned for CRICKET!! It will always work perfect for you if you leave it alone I cant be responsible if anyone changes anything but you can always post your problems in this thread and I will be more than happy to help sort it out.
"
and this; "Fully working and tested Cricket WAP and MMS/SMS with no problems! I did a lot of tweaks to registry and provisioning to make this possible as the base I used(1.3.4) was originally meant for Sprint!! I pulled a lot of "All Nighters" put it that way lol."
so i thought i don't have to set up my MMS/WAP...
and do i still have to call *228??
***EDIT***
i just called *228, and they said: "sorry we cannot program your phone"
my internet still works... but that's the only thing that works so far, i can't make calls. or send txt msgs.
X-Kenshin-X said:
ok in the version of your ROM that i installed, which would be the V1.1 Heavy, it says in that post this:
"Messaging and Connections settings: <--Please do not mess with these as they are fine tuned for CRICKET!! It will always work perfect for you if you leave it alone I cant be responsible if anyone changes anything but you can always post your problems in this thread and I will be more than happy to help sort it out.
"
and this; "Fully working and tested Cricket WAP and MMS/SMS with no problems! I did a lot of tweaks to registry and provisioning to make this possible as the base I used(1.3.4) was originally meant for Sprint!! I pulled a lot of "All Nighters" put it that way lol."
so i thought i don't have to set up my MMS/WAP...
and do i still have to call *228??
***EDIT***
i just called *228, and they said: "sorry we cannot program your phone"
my internet still works... but that's the only thing that works so far, i can't make calls. or send txt msgs.
Click to expand...
Click to collapse
Ok if you dont understand it just give up. Please quit cluttering up this thread with YOUR problems. a ROM's settings and PST settings are two different things and they both need to be set up right to work!!
MY Cricket ROM is already set up for WAP/MMS, but not everyones version of a Cricket Rom is set up perfect. But your PHONE's PST settings still need set RIGHT as a ROM does not touch that!!
PST settings are independent of ROM settings.
Your problem with dialing *228 is because YOUR SPC CODE IS NOT SET TO ALL ZERO'S!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! SPC code needs to be all Zero's and you need a Cricket PRL loaded (updated) in PST before dialing *228!
It says that in the beginning of this thread. No wonder I am mad. Read well before you follow through
You people seriously have to learn how to read things before trying something. Read, read, read, read, read. Until you fully comprehend what you are trying to accomplish and THEN mess with things.
Edit: My threads are not meant to BABY STEP someone new through the entire process of unlocking, flashing, and programming a phone. NOT AT ALL.. The threads are meant to Help and that is what they do..
ok... wow there
look the reason why i was asking is because you only included this link in your ROM posting thread, you did not include any other links or procedures...
same here, you only include information to do one thing, i see no relevant information pointing to the "other settings" you're talking about.
EDIT:
i had already previously unlocked my phone with another program, but just to double check i used your unlocking pack and followed the instructions. when i run BAF MSL Grabber, it already gives me my MSL code as being 000000, so i am assuming my phone is already unlocked.
but i went ahead and tried to go trough with your thingy anyways, and i got stuck at the ##3424# thing. none worked, ##3424# nor ##3424
i had to use the DIAG(DRMRouter) that took me a while to find in your ROM and i am in QPST right now...
hey Ryan... actually everything works, it's just i was unsure if i still needed to "go down to the store" to get my phone line switched to this new phone with cricket...
neways everything works... including mms, internet, so on so forth. i just haven't tested the gps
Awesome man, I knew I would fuel your fire to get it working. Thats why I am who I am lol. My GPS works awesome. Alot of people dont know this but Agps works with my Cricket ROM. Take care.
Updated the PST settings
I have updated this thread to clear up any problems with New Cricket users that have never had Cricket before. I re-phrased a few things and changed a step so that both New and Current users will not have any problems.
actually about what i said in my last post, i never tested the GPS on the rom so i don't know if it works...
i just know that if i go to google maps, it never locks on to a satellite, dunno why
oh btw, i had to tell yah, the reason why i couldn't dial *228 is because at least in my area, cricket won't recognize the 1050 PRL. everything works with it, but it just won't let me do the *228 thing.
i had to use the 1042 PRL, and then everything worked, just a heads up.
RyanMogul6800 dude not only do I want to say thanks for the settings thread, but your ROMs are awesome. Quick question to anyone who might be able to answer it, this is the first time I get a mogul not to work on mms, i tried all settings, and read through a lot of threads and still no dice, is it possible that the settings might need to be refreshed on the cricket network side? internet and sms work flawlessly, just MMS does not work, it stays stuck at downloading 0%. Thanks in advance!
EDIT: Ok I have ryans heavy rom, and it may seem weird but I installed his mms wap fix from his sig and now it works flawlessly!
Glad you like, but MMS works on MY ROM without that CAB
My ROM works flawless without using the MMS fix CAB from my Shared Site. That CAB is for users not using my ROM or that have messed up their settings on their own.
Now assuming you already have PST set correct and that you are Using MY Cricket ROM.
First thing you do after MY ROM is booted up and running is MAKE SURE ITS UNPLUGGED and WI-FI is OFF! I hate when people leave the phone Cradled for all of their Flashing and Programming. It needs wi-fi off and needs to be unplugged to set up WAP. You need WAP (DATA) set up for MMS to work. So you want to make sure you have unlimited DATA plan with Cricket.
Now after the Phone with MY ROM is unplugged and wi-fi is off simply open up Internet Explorer and Navigate to a real webpage(yahoo.etc) and then enter the info and password click save. Done.
There are some cases after setting up with Cricket needing to call them again and have the account refreshed on their end. There are other instances where Crickets end takes a long time to refresh automatically on their own.
I really believe you ran into a Cricket account refreshing delay problem. Installing the Arcsoft MMS fix cab had nothing to do with why your MMS works now. Do not try uninstalling that CAB to prove me wrong as it will mess up the ROMs settings and will require you to hard reset.
What you could do if you really want to know for sure, is hard reset then let the ROM boot and set up the Internet with phone unplugged. After that I am willing to bet that you can send and receive MMS without installing the CAB we are referencing.
I am glad you like the settings and the ROM.
are you working on a WM 6.5 rom for cricket?
Thanks,
Scott
Related
Carrier: Alltel
Started with WM5 ROM.
Flashed to DCD's 2.1 WM6 ROM last week, no issues noted.
Yesterday flashed to 2.2 WM6.1 ROM and now whenever I get a data session going in a strong EVDO area I get dropped down to 1x when the data session finishes connecting?
I've moved back to 2.1, used no2chems 6.1 ROM and back to DCD's 6.1 ROM. Same problem all around now.
Radio problem maybe? Or user? If radio, anyone get me a link to the original 1.4?
Thanks in advance if anyone has any tips, I've tried looking around but only find people with MMS or other issues.
---------------------
This solution apparently only works for Alltel customers, if anyone finds solutions for Sprint/Verizon/Telus I'll add the solution to this post.
ALLTEL:
1. Enter EPST (##778), Edit (password= 000000).
2. View Info (left soft key).
3. Choose the "Security" item.
4. In the "HDR AN AUTH Password(LONG)" field, click to highlight.
5. Menu (right soft key), Edit
6. In the "Value" field, enter your Hex ESN (make sure all characters are CAPITAL, lowercase will FAIL).
7. Ok. Menu. Ok to save, then reset.
--------------------------------------------
SPRINT:
MADMARTlGAN said:
Hey in case you guys are still having problems with this, I can tell you what worked for me with Sprint.
You'll need your unlock code, if you don't have it, you've gotta get it from either Sprint or from one of the tutorials i've seen floating around here and other forums.
1. Sync your titan to back up your data.
2. ##786# Choose edit, enter your unlock code, then choose menu>restore. This will reset everything to factory settings.
3. Reset
3. ##UNLOCKCODE# Again choose edit.
4. Both MDN and MSID should be your wireless number (this was confirmed by Sprint T2 tech support)
5. Reset
6. Call your voicemail to make sure your phone service is working.
7. Connect to the internet. It should trigger IOTA/Provisioning and then EVDO should be working.
8. Resync your **** and you're good to go.
Hope this helps, it worked for me.
Click to expand...
Click to collapse
I think with Alltel you get 1x when roaming. Do *228 option 3 < Thats to activate your phone if you haven't already
Then do *228 option 2 to update your roaming preferences which ridded me of roaming in coverage area!
Americanmetal said:
I think with Alltel you get 1x when roaming. Do *228 option 3 < Thats to activate your phone if you haven't already
Then do *228 option 2 to update your roaming preferences which ridded me of roaming in coverage area!
Click to expand...
Click to collapse
Thanks for the response, I've been through that already and same results...
I even went back to the stock Alltel ROM and Radio, same thing.
With PRL 30029 AND 40029...
Oh well, I'll figure something out as I love the speed of DCD's 2.2!!!!
jake1s said:
Yesterday flashed to 2.2 WM6.1 ROM and now whenever I get a data session going in a strong EVDO area I get dropped down to 1x when the data session finishes connecting?
Click to expand...
Click to collapse
Did you check Start->Settings->Personal->Phone->Services->Mode of Operation to make sure it wasn't set to 1X only? I think that was the default setting on my phone.
I had this same problem, and then I reflashed with the 3.16 sprint rom twice and it went away.
Appreciate the responses, but I don't have the "Mode of Operation" on my Alltel 6800. And I've reflashed all kinds of ROMs with no luck...
Thanks for the ideas though...
jake1s said:
Appreciate the responses, but I don't have the "Mode of Operation" on my Alltel 6800. And I've reflashed all kinds of ROMs with no luck...
Thanks for the ideas though...
Click to expand...
Click to collapse
With the newest Advanced Config app, you can unhide the "mode of operation" option in there. I got it from here somewhere, do a search. I doubt this is your issue. I had this problem yesterday with Sprint. I got data in 1xRTT, but not EVDO. I ended up calling Sprint and they had to deactivate and reactivate the internet services on my phone. Immediately it worked like a champ.
I had this problem also and was able to take care of it by going into EPST (##778) and going under the security settings and putting the ESN Hex Value of Your Phone under the HDR Password. Mine got lost whenever I upgraded the radio. This will allow you to lock back onto the EVDO network
corwinb said:
I had this problem also and was able to take care of it by going into EPST (##778) and going under the security settings and putting the ESN Hex Value of Your Phone under the HDR Password. Mine got lost whenever I upgraded the radio. This will allow you to lock back onto the EVDO network
Click to expand...
Click to collapse
THANK YOU! THANK YOU! THANK YOU!
That did the trick (after I did it a second time and made the letters capital) and now I'm cruising EVDO style!!
Thanks!!!!
Hi I have this same issue.
i typed ##778 send
and get the view, edit , and cancel options.
do i find the hdr password under the edit?
when i choose edit, i get a password prompt and i do not know the password.
i am on dcd rom 2.2.0
i edited mine, and it does get on ev instead of 1x so i was glad but when i opened ie i cant get a data connection up now at all???
corwinb said:
I had this problem also and was able to take care of it by going into EPST (##778) and going under the security settings and putting the ESN Hex Value of Your Phone under the HDR Password. Mine got lost whenever I upgraded the radio. This will allow you to lock back onto the EVDO network
Click to expand...
Click to collapse
I just checked and I have a bunch of garbled characters in this spot. Does anyone else see something like this?
What did you guys have in that slot before you added your esn hex number?
the password you need is unlock code you can only get from sprint.
i also had the weird characters, i edited these out with my esn hex as mentioned and now i cant get a data connection at all, i get an error that i cannot connect. Anyone with any idea on what i can do?
I thought of downgrading the radio and then installing this one again and starting from scratch any better ideas?
My HDR password is also extended ASCII characters, has been for every ROM version I have run, and I get EVDO and on the Internet as well. I thought that was a problem when I had no data connection from a previous ROM, but it wasn't.
What worked for me was to go all the way back to the official 2.17, then to the leaked 3.16, etc. I made sure everything was set up and working properly on each version before moving on to another ROM.
excess4 said:
the password you need is unlock code you can only get from sprint.
i also had the weird characters, i edited these out with my esn hex as mentioned and now i cant get a data connection at all, i get an error that i cannot connect. Anyone with any idea on what i can do?
I thought of downgrading the radio and then installing this one again and starting from scratch any better ideas?
Click to expand...
Click to collapse
not true there is a program to find out the msl code for your phone if i was on computer i would give u guys the link
aatreya said:
I just checked and I have a bunch of garbled characters in this spot. Does anyone else see something like this?
What did you guys have in that slot before you added your esn hex number?
Click to expand...
Click to collapse
Again, I'm on Alltel so maybe for some unknown reason there is more to it for you Sprint users.
But, my MDR Password field was goofy stuff, deleted it and put in my Hex ESN in ALL CAPITALs and I stay at EVDO when my data connection is made now.
Deleted MDR PASSWORD and put esn hex, internet not working
ok guys i messed up pretty badly and deleted the MDR password and put my esn hex instead and now i cant get on the net.
I have an HTC TITAN running DCD 2.2 and latest 3.27 radio
any suggestions on how to get the password back????
aatreya said:
I just checked and I have a bunch of garbled characters in this spot. Does anyone else see something like this?
What did you guys have in that slot before you added your esn hex number?
Click to expand...
Click to collapse
yes i also have a bunch of giberish in there. i am afraid to change it becuase there will be no way for me to put that giberish back in there with all those weird looking characters.
i found the edit password which was a bunch of 00000 as many as the field would take
and i understand some people now get ev but no data connection now. i am on verizon and i dont know if that will happen to me as well.
my connection now says ev and doesnt change back to 1x anymore so i am going to leave this as is for now and not change it.
also my a-key is blank if that makes a difference. phone works fine though.
whatbish said:
ok guys i messed up pretty badly and deleted the MDR password and put my esn hex instead and now i cant get on the net.
I have an HTC TITAN running DCD 2.2 and latest 3.27 radio
any suggestions on how to get the password back????
Click to expand...
Click to collapse
you mean hdr password right? I did not see an mdr password listed anywhere
I installed the dcd USCC Carrier 20080801.cab on my 6.1 rom, and the data connection still will not connect. Dialing #777 with no user name/pw/domain, and it still fails.. is there a newer cab? I am in Maine.
Thanks.
Call provider ask them to reset your DMU keys. You may also need to blank yours out. ##778 under the MIP Default Profile HDA and AAA. Should look like encrypted text.
-1
I had an HA and AAA, with encrypted text, cleared both.. calling operator to reset now, cuz my resets weren't enough to fix it.
Ugh, operator says there is no way to reset dmu keys..
Did you by any chance back up your phone programming with QPST? I did to be safe, but luckily did not have to roll back to it after programming the phone.
If they get you back up and working, or end up replacing your phone, use QPST to back up service programming so that in case this happens again, you can restore it and not lose data.
What steps did you do to upgrade?
I had to use the registry change to get my SPC, then used QPST to back up my service programming.
Ran the bootloader 2.40, installed radio 3.42.30, then DCD 3.2.3 and everything went smooth, the cab file pretty much contains the USCC theme, and possibly a few tweaks, but it does not contain the info to restore the data services as it's a unique encrypted ID that should be unique for each subscriber. The only way to get it back is from a backup, or from their customer service.
I imagine if you can take it to one of the stores that has a tech onsite, he could put the info back in for you, however, he is gonna probably be rather upset that it's not their rom on it, and may refuse to work on it. Maybe at first you can call and ask to speak to their technician, maybe he will help you over the phone, just depends on the tech.
Good luck,
BTC
I have a friend with a motoq with same carrier.. can I pull the settings from theirs?
will research spl and qpst, any good recommendations before I go down a wrong path?
I believe the settings are unique to each customer, so while he will have settings, they won't be yours. I suppose it's possible his might work on yours, however if it does, then he will get billed for any data you use. Since his is unlimited as well, it wouldn't probably cost him anything, but it wouldn't be correct, and may cause him issues later, so I would recommend against it.
You really need to get a tech on the phone who has intimate knowledge of this phone, he should be able to get you the settings you need, but I'm sure he will want to know why it stopped working... Maybe someone else here can give you a plausible story that you can give him for why it got erased.
BTC
Sometimes activating and old phone, make couple calls and re-activating the 6800 works for resettting those keys.
I have QPST, but no phone is showing up. Can't find a good thread on using qpst. My friend is willing to share his data connection information, if I could figure out how to extract his and put it on mine.
MetalHd said:
I have QPST, but no phone is showing up. Can't find a good thread on using qpst. My friend is willing to share his data connection information, if I could figure out how to extract his and put it on mine.
Click to expand...
Click to collapse
Look for GC's GPS Fix wiki, it has good instuctions on how to get QPST to see your phone.
BTC
Well, I got lucky, I hope.. I called Data Services at USCC today, and the HTC and WM reps were on site.. I got the tech to get a stock 6.0 rom, supposedly coming via email.. then I can start over and do it right this time?? !!!
If they send you the rom, please let me know, many many many of us would appreciate having a stock rom available to reflash our phones. Hopefully it will flash all the ROM so that it doesn't make the phone worse. Several people said that there are settings that don't get erased when flashing a rom that could cause problems. So if you get it and it works, please share the file with some of the developers here so we can get it available for download for those who need it.
BTC
MetalHd, did you ever recieve that ROM? If so is it posted somewhere?
Sorry, never got a rom.. they sent me a new phone.
Did they give you any problems about flashing the phone?
Before trying to upgrade this phone, be sure to learn to use QPST and backup your phone programming, then after flashing the radio and your first rom, re-run QPST and write the programming back to the phone. Then the cab will restore data every time you flash in the future.
Also you can do the aGPS update and make GPS work perfect on the phone.
BTC
#3
record your EPST information just incase you end up like i did with the data connection not working.
Optain this information by
start<programs<file explorer<my device<windows
tap on EPST file. (should be the 28b one if you have 2)
Choose View
tap view info (left soft key)
tap M.IP Settings
The following should match,
M.IP SETTINGS
Number of Profiles : 6
Active User Profile Index : 0
MIP_MODE : Mobile IP Prefered
MIP Registration Retries : 1
MIP Registration Retry Timeout : 2000 ms
MIP Pre-Registration Timeout : 3
Mobile Node-HA Authentication : Enable
Send a Registration Request Only in Use : Enable
Dormant Hanfoff Optimization: Enable
View info<M.IP Default Profile
M.IP Default Profile
Enable Profile : Enable
NAI : **********@uscc.net (*'s are your ten digit MSID number)
MN HA SPI Set : Enable
MN HA SPI Value( Hex ) : 10E1
MN AAA SPI Set : Enable
MN AAA SPI Set Value ( Hex ) : 2
Reverse Tunneling Preferred : Enable
Home Address : 0.0.0.0
Primary HA Address : 255.255.255.255
Secondary HA Address : 255.255.255.255
DMU public key(PKOID) : 41
Hit ok
Bring up "Phone"
Dial ##000000
tap talk
Record
MDN : **********
MSID : **********
Home SID/NID #1 : ***/*****
taken from Here
i had the same problem when i went to the gps radio and this fixed the problem
Yeap thats right three days with Network Support and they can not figure out why my phones not updating. Anyone else have any ideas before i myself agree with them that it is my equipment and toss it on ebay
It is a Alltel 6800 that has the Opal2.40 loader with the New Verizon 3.57 Update
Any ideas are better than anything i have at this point my mind is tired.
Forgot to mention tech support asked me to go ahead and clear the storage and reflash the verizon update again so i am at Verizon Factory Defaults other than I have changed the SID to match the local Verizon SID
what are you trying to do?
I am just trying to get Data Access for Pics and Video messages as well as Web Access .... The phone works for Voice calls and will send and recieve regular txt but anytime it Dials into #777 it comes back Error 11 PPP Connection Error
I have went into the ESPT and checked my secuirty and its [email protected] and vzw so thats ok.....the techs say that my phone is not updating its key its been soft reset and hard reset more times in the past 3 days than i have had sexual relations with anyone other than myself
well lets solve one problem at a time. first, the sexual relations issue. go get yourself laid a bunch of times and then we can continue working on your phone.
i'm not sure about this MyMDN business, but your mdn is your phone number. your credentials for the data connections should be your 10 digit phone number:
##########@vzw3q.com
password is vzw.
also, check your vzw mdn registry key and make sure it is set to your 10 digit phone number
[HKLM\Software\Arcsoft\Arcsoft MMS UA\Config\mm1\wspheader]
X-VzW-MDN should be your number
I'm married...think thats my problem on the first one someone told me the ring goes on the nice things about her go away
yes my phone number is what i ment by mdn @vzw3g.com
also i am a newbie on the registry so i will have to report back to you on that when i have time to download the software for the registry
ok i followed HKLM\Software\Arcsoft\Arcsoft MMS UA\Config\mm1\wspheader] and i have no entry for X VzW MDN
I have
Accept
Accept-Charset
Accept-Language-
User-Agent
x-wap-profile
Since that phone was Alltel to start, has Verizon ADDED that ESN to their database??? Most likely they haven't..... The ESN is the Equipment Identification Number. My understanding is that it gets sent when a data connection is initiated. The MDN(Mobile Directory Number)@vzw3g.com will work but I suspect the ESN is not validating.....
EDIT - Humm, I didnt even see your response above.... So add the Key above and see what happens....
Here's what that section should look like...
"User-Agent"="utstar68kv1"
"Accept"="application/vnd.wap.multipart.related"
"x-wap-profile"="http://uaprof.vtext.com/utstar/xv68k/xv68k.xml"
"X-VzW-MDN"="your 10 digit cell number"
"Accept-Charset"="us-ascii;utf-8;iso-10646-ucs-2;iso-8859-1;gb2312;gb13000"
"Accept-Language"="en"
...
yea i spent all of last week waiting on the to validate the ESN which they finally did waiting long enough is the key it just took them a while to get the ESN in the system and show a VX6800 and set-up all the "pervision" to match my phone (i know that is off in spelling)
Ok I added that string into the reg and did a soft reset and check the value to make sure it stayed and it did and I still get error 11
all i needed to enter was my telephone number not the @vzw3g.com on the end correct?
chanderson said:
yea i spent all of last week waiting on the to validate the ESN which they finally did waiting long enough is the key it just took them a while to get the ESN in the system and show a VX6800 and set-up all the "pervision" to match my phone (i know that is off in spelling)
Ok I added that string into the reg and did a soft reset and check the value to make sure it stayed and it did and I still get error 11
all i needed to enter was my telephone number not the @vzw3g.com on the end correct?
Click to expand...
Click to collapse
Here, I made you a cab to add the necessary info minus your cell number since I don't know it..... So here's what you do.
1. go into the registry and delete what you added. Hence - Delete whatever is listed under the WspHeader....
2. Run this cab.
3. Go back to WspHeader and change the X-VzW-MDN key from the 10 X's that I put in to your cell number.... ie: 1234567890, then exit the reg editor and reboot....
EDIT - The info in that cab came straight from MY registry.... Minus my cell number.....
Let us know...
ok cleared the reg...installed cab
reset
changed your xxxxx to my number and still ppp error 11
Have you tried to install DCD's carrier cab? I'd try that next, then reset.....
Get the Verizon carrier cab here
http://dcd1182.n715dp.com/index.php?dir=carriers/&download=dcd+Verizon+Carrier+20081031.cab
are u running a custom rom? try running dcd carrier cab, i have used it to fix a few phones i had switched to different carriers and data didnt work
Ok, quick question as i am new to the flashing never really tried any until now was too scared until Alltel screwed me by selling out.
Can i just put this on my card and run it from inside WM6.1?
Hey, i had this problem in the past. First let me say that i am not an HTC guru like most people here, so research anything i have to say.
Sounds like everything obvious is set correct, take a look in EPST. Dial ##778, select edit (but be careful not to edit anything, if you select view it will not allow you to see the needed information). It will ask for a security code, it is 000000. After it loads select view info, then Security.
The following information should be present.
HDR AN AUTH User Id : [email protected]
HDR AN AUTH Password : encrypted data characters
PPP User ID: encrypted data characters
PPP Password : encrypted data characters
S.IP DUN User name : [email protected]
In my case there were no encrypted data characters in the appropriate places.
The easiest way to resolve it from what i've read is to activate another device on your account then switch back to the desired unit. In my case i had to convice VZ Customer Service to completely reset my account. I believe there's a DMU code somewhere also that has to be 10. Search for PPP error code 11 security and i think you'll find something.
i got
HDR AN AUTH User Id : my#@vzw3g.com
HDR AN AUTH Password: a few numbers looks like my HEX ESN
PPP User ID: my#@vzw3g.com
PPP Password : vzw
S.IP DUN User name : my#@dun.vzw3g.com
I have another phone i could swap too and then swap back....its easy with verizon you just dial *228 and press 3..put in your phone number and last four of your ssn and your done
tried the swapping of the equipment and that didnt work...it did however get on line one time and i closed it and tried to connect again just to get the Error 11 again
Search for PPP error code 11 security, choose the "waiting for a dmu reset", i don't know how to embed it. That thread contains what i did to correct my problem.
Maybe the they are verizon specific, but your settings do not match mine nor any other xv6800 i have owned.
I have an idea, follow the instructions for the TP and getting EVDO on it.
Don't try this until you ask a few people first.
I have an idea, follow the instructions for the TP and getting EVDO on it.
Don't try this until you ask a few people first.
ok...here is my update on status...
Still no Data, BUT
When i was on the VZW Update ROM i had info in the following fields
HDR AN AUTH Password:
PPP Password
also
in the MIP default i had data under
AAA Shared Secret, and HA Shared Secret
NOW I used the latest dcd_titan_3.3.4.exe and I have nothing in these spots except 0000..ect under HDR AN AUTH Password
i went back to my LG 5500 and took allllll data off of my account waited like 4 hours and swapped back and still nothing.
only thing now is i think i will go back to the VZW Rom and call for a DMU reset and beg some more
I had the exact same problem after flashing to DCD 3.2.6. I had to call Verizon and have them generate a new A-key (26 digits).
You might have to call back a bunch of times or press the rep you get to generate the key for you (any of them can, they just don't know how).
Not sure why a new A-key would fix that problem, but I fought with it for quite a few days before finally getting it figured out. The data has worked flawlessly on my phone ever since.
Post back if this works if you would.
Some one PLEASE help i have tried to run several prl's including the 1007 i think it was anyhow (the latest 3g prl..) only 1x works for my raphael on cricket ...im getting frustrated... thanks
Wait... Cricket has 3G EVDO? No way... only seen there stuff work at 1x.
jnellz said:
Some one PLEASE help i have tried to run several prl's including the 1007 i think it was anyhow (the latest 3g prl..) only 1x works for my raphael on cricket ...im getting frustrated... thanks
Click to expand...
Click to collapse
You will only get 1x on a CDMA phone flashed to Cricket. They use a different band for their 3G that is not supported by Sprint / Verizon Phones .. It's a Cricket Thing.
THANKS SO MUCH thats what i figgured i just needed a second opinion DAMN! HTC FUZE
Here i come
Uh well, not true. Def not true. Im new to this flashing stuff, only on my second day. I purchased my vogue already flashed to cricket but it was VERY GENERIC. No touchflo, nothin, just windows 6.0 nothin else. It was getting evdo signals at that time, but i needed to reset some registry settings, which i did and was getting evdo signals with working internet and mms....THROUGH EVDO......NO BS THIS WAS JUST a day or 2 ago. But, problem was, i put touchflo on it, and didnt realize that the previous owner had somehow filled up the memory on the phone with applications and files that were nowhere to be found. It was crawling...So my solution.....? I decided to re-flash it myself because i knew that would delete all the useless stuff on the phone that i had no use for. I flashed the stock sprint rom from the htc website to get the most current radio, then unlocked the phone, then re-programmed it. When i got the phone it already had the 1050.prl file on it, which is an EVDO PRL!!! Go to corolada.com and look at the left side of the page and there is a list of EVDO AND NON EVDO CRICKET PRL's 1050 being the most universally recognized. Fast forward to now, I have finally found a rom that is fast and clean that i plan on keeping. Well now theres a whole nother problem. My phone is no longer recieving EVDO signals. BUT CRICKET HAS WORKING EVDO I KNOW FOR A FACT I have had so many cricket phones that connected to pic messaging and internet through evdo. Im sorry if i misunderstood your post and you were just saying that a flashed phone from sprint cant get evdo, but either way, i know for a fact that a flashed sprint phone is fully capable of sending and recieving cricket evdo signals because i was surfing the net on my vogue through cricket evdo just a day or two ago. Can anyone figure this out??? IVE tried reloading the prl. ive tried different prl's. ive even tried puttin the original sprint prl on the phone and then changing it back to the 1050 cricket prl, and to no avail, no evdo signals. someone please help, im pulling my hair out. why couldnt i just leave the phone alone when it had evdo? why did i have to go and try to make it pretty?????
sound like it's not authenticating ##DEBUG# ,debug info,"HDR" it should be 1=Athenticated
if not, ##778# , M.I.P Default profile, Delete AAA & HA shared secret & resest
jtmfnslim said:
sound like it's not authenticating ##DEBUG# ,debug info,"HDR" it should be 1=Athenticated
if not, ##778# , M.I.P Default profile, Delete AAA & HA shared secret & resest
Click to expand...
Click to collapse
HERES SOMETHING I GOT FROM "HOFO" that might help out some of u cricket people with PST setting issues/ hope this helps a lil:
==========================================================
CRICKET PST Settings Thread! by Ryan Mogul
This is for people who want Cricket to work perfectly, just follow these instructions not skipping a beat and you will be OK from then on! If you are not having problems obviously skip this!
This thread is assuming that you already have your phone Unlocked(spc code all zeros) It is also assuming that you already have a CRICKET PRL file loaded in PST. If you have my ROM flashed than PRL's are on device memory we will get to that below.
1. Now first thing you want to do is have a good Cricket ROM installed like "clears throat* Mine lol.
2. Now if you are starting from a fresh flash OK, if you are starting from a Hard reset OK, we can continue. If you have a ROM installed that is having problems I recommend a hard reset and skip customizations using stylus when it says you have 3 seconds.
3. Now open your Phone Application and go to options and make sure smart dial is off. Then dial ##778 call button, now click edit and enter six zeros. Now click view info and goto PRL, now check to make sure you have a CRICKET PRL(1013,1014,1050 etc.. there are others)If you dont have one loaded and you are using my ROM then you can click update and it should goto main root, pick prl 1050. Let it do its thing and restart. If you already have a CRICKET PRL then skip the update step.
4. Now cancel out of EPST if you didnt update PRL. (for both people who had to restart and people who didnt) <--open phone application again and dial *228(this will make sure base settings are good so i will not have to explain as much, it will also download a local EVDO prl to where you are), it will dial cricket and do its programming thing. Do not interupt this. Let it do its thing even if it restarts. Now when you are back in action we can continue.
5. Open phone application and dial ##778 call button, now click edit and enter six zeros. In main page the only two things we are going to do is change the NAM name to Cricket, and check the MSID number make sure its a 10 digit number thats in your area code BUT it IS NOT your PHONE NUMBER!! If its fine we can continue, if not you may of skipped the *228 step so you need to do that or you need to obtain this from calling Cricket.
6. Now click view info and goto AKEY and make sure its blank, nothing there. Now click view info and goto NAM settings, NAM name should be Cricket, Mobile Directory number should be YourTenDigitPhoneNumber, MIN1 should be that other phone number the (MSID) that is not your phone number! but it should be 7 digits, ex: sevendigitnumber, MIN2 should be just your area code. MSID should be 10digitMSIDnumber <--again not yourphonenumber!, MCC should be 310, MNC should be 00, NMSI should be your MSID(XX10digitnumber<--not your phone number) THE XX'S should be zeros, ex: 007185548692, Now if all these settings in this paragraph didnt need touched assuming you didnt skip any of my steps(which they shouldnt be touched i am just making sure) we can move on.
7. Click view info and goto CDMA settings, we are going to make sure they are set right and change a couple things for Clearer voice transmissions, people will compliment how good your phone sounds even in some cases. EVRC should be set at Disable, Home page should be Voice 13k, the Two below it the Same Voice 13k.
8. Click view info click modem settings, change slot cycle index to 1, This will make the phone ring a little sooner, also get your texts a bit sooner. The other 4 options should be Auto, Auto, Enable, No in Order from top to bottom.
9. Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the passord below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
10. Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
11. Click view info and pick MIP Default Profile, Enable profile should be enable, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 68.28.15.12, secondary should be 68.28.31.12, HA shared secret and AAA secret should be cricket <--lowercase, DMU public should be 0, MN Authenticator should be 0.
12. Click view info and pick MIP customer profile 1 and make sure its Profile enabled is disabled. Now do the same with the other 4 below it.
13. Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778, we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to yourtendigi[email protected], password should be cricket<--lower case, same for PPP user id and Password make them same as HDR.
14. Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both cricket<---lowercase, then click menu OK and let it reset.
Thats it! PST settings are perfect for CRICKET, you have a Local EVDO prl file installed, and you are Authenticated for Data and EVDO, now if you used my ROM just go to internet explorer and goto a real page, and follow instructions but remember to click save password!
Thats done, every flash from now on should never affect your PST settings and you should always be authenticated. I hope this helps everyone.
Cricket 3g network
I just got off the phone with cricket customer service. I wanted to upgrade to there 3g network. The representative said,"the 3g is reserved for original cricket phones.
it doesnt matter if you put a 3g prl on the cdma raphael because it is a dual band phone and crickets 3g network only works on their new triband phones so your still stuck with 1x and evdo
Is there anyway to flash the Droid Razr to metro pcs and if so can someone provide me with a link? If I'm posting in the wrong place just let me know.
i'm thinking you may need more than just flashing for that.
Do you know what I might need then? This verizon bill is killing me. I know people have successfully flashed the razr to Cricket. I mean I know I'm gonna need to root kit which isn't a problem I've done that kind of thing plenty of times and I've just been procrastinating on doing it on my Razr for some reason.
i know how to flash it to metropcs just cant get it into the metropcs system so if someone can help me as far as getting it into the system i can definately help them on the falshing part
houdini
you just have to houdini the phone, tha'll will get the phone in their system
candel said:
you just have to houdini the phone, tha'll will get the phone in their system
Click to expand...
Click to collapse
ive tried running it through houdini and it isnt on their compatible phones list
Flashed on cricket
Noodlez916 said:
Is there anyway to flash the Droid Razr to metro pcs and if so can someone provide me with a link? If I'm posting in the wrong place just let me know.
Click to expand...
Click to collapse
I found this
http://www.cricketusers.com/verizon...-cricket-wireless-talk-text-mms-internet.html
At the moment this is a placeholder for notes. The tutorial might have to be finished by someone who has more time than me to work on this device. Mine is on Verizon now. I will probably poke at it a little bit more when I get home and back to a normal schedule, but throughout December, it's going to be hectic for me. I'm going to try and add pictures so someone will have some knowledge going into this where I had none. If someone can get a hold of a Bionic tutorial, this might be similar.
Currently talk and text works but 3g data drops out. It works when it's connected but wants to cycle off and on A LOT.
As a good rule of thumb, always try to backup your settings before modifying them.
DIAG MODE
Verizon Droid RAZR Diagnostic Mode How To
NOTES (semi based off Thunderbolt tutorial)
CDMA WS 3.5 or later will give you more options and another method of writing data profiles to the device.
QPST does work HOWEVER you cannot read and then write the original settings to the phone (after modification of course). You have to start fresh and write ONLY.
CDMA AUTO (PRL) MODE (info from RLockwich)
Go into *#*#4636#*#* - Went into phone information (Set to CDMA Only PRL, DNS check allowed, Query CFU enabled).
QPST
Add the port for the device if required under QPST configuration. It's going to be the DIAG port. Just check device manager to see what port that is.
Use the Service Programming application under the QPST folder to access the phone. Connect to it but don't read.
Now follow this tutorial to write the proper information:
http://www.cricketusers.com/flashing...s-cricket.html
Write to the phone. Reboot it once all the writing is done and catch the boot to put it back in DIAG mode. If you don't it's no big deal, but you will have to power it down and get it back in DIAG mode before continuing.
CDMA WS
Open up CDMA WS and connect to the port with the RAZR. Go to the security tab and send the SPC 000000. Then go to the memory tab and send the DROID NV items which can be found at whiterabbit.org. It should write the NV items and fix the data.
UPDATE: The following might be required
Go to the "Other" tab and navigate to "R-UIM" then click read.
Change it to "NV Only" and write to phone. It should say Successful
Close out CDMA WS and reboot the phone.
Phone Settings (info from RLockwich)
Go into the ##PROGRAM select option 14 for LTE I turned off LTE bppanic, LTE Movement detection, and disabled Class 1,2,2 APNS
Additional Instructions (info from RLockwich)
Just went through all the settings again, I hope everyone can have as much luck as I just did. I was thinking, and I remember seeing the end of the thunderbolt tutorial says the last step is to remove the 4G LTE microSIM. I had tried that before early on when I first flashed it, but when I removed the card, it showed No Sim, no network connection and a SIM symbol with a exclamation point. I just tried it again a hour ago...Pulled the SIM, showed no network and then I rebooted the phone... FIVE times on and off all with immediate and STABLE 3G at 10 minutes a time between rebooting. FIXED. Done messing with it.
UPDATE 12/19 - After this last post it's been 4 days since we cracked the 3G cycling issue, and my phone is working excellent! I'm very glad I was able to be a part of this and get credit work any work I put into this.
Dina's Notes:
Got everything working THANKS to Chris and RLokwich! Oh, and for those of you that are not yet successful with this flash, just re-read the entire thread. Everything you need is HERE!
It was not all smooth in the beginning.
Insights:
1) No need for BP tools. If your phone is on the homescreen, just connect it to the cable, choose PC mode and set up the port in HW.
2) Mine took like 5 master resets before 3g showed up. So in case you are pulling your hair as to why 3g not showing up, master reset the phone. Turn on wifi. Bypass activation screen (backwards C method works if you keep trying for like 2 minutes), go through the set up pages and 3g will be there.
Everything is stable so far. 3g working like a charm.
Discovered a secret!
If you do not get 3g up, make sure to Enable at least one APNs in the LTE settings (##PROGRAM menu)
Now time for some icecream
Read more: Full Flash Verizon Motorola RAZR to Cricket Wireless (talk, text, MMS, and Internet)
MMS (needs to be tested)
The only thing I've realized now that is wrong, is no MMS. I have MMS through the tutorial on bypassing the apn through GoSMS, but I would very much like to not have it to be that way. I thought early on in this flash that I did have MMS, I think I was just being a smart ass so I changed some settings in ##PROGRAM for the SMS/MMS part that I copied from the Thunderbolt tutorial. I don't know if I messed something up. I was also thinking I've seen people having two Cricket apns? One for internet and one for MMS, does anyone know if that may fix it? I was thinking it may be that, but in my apn for cricket already, I edited it and filled in all the MMS settings for that APN. Maybe that's something I did wrong, I don't know.
If anyone does have working MMS on their flashed Razr, please post anything that might help us. Please post all your settings in SMS/MMS in ##PROGRAM and into your APN edit settings for Cricket APN you have for MMS (if you have anything filled out in the MMS blanks)
##Program
Enter SPC "000000"
SMS/MMS Settings
MML Server Name
[email protected] > wap.mycricket.com
Address for Upload to Online Album
438749 > 111111
Maximum MMS message size (Byte)
1228800 > 228800
SMS to Email Gateway
Anyone? Currently set at 6245
Try adding an APN for Cricket's settings or modifying the existing APNs to reflect Cricket's MMS settings.
this is what i used to get my phone on metro but the only issue im having is getting the phone itself into metropcs inventory....
i have a droid 3 esn im willing to use or if theres a way to just get the razr into the system that would be the better method
adventuressmalik said:
I found this
http://www.cricketusers.com/verizon...-cricket-wireless-talk-text-mms-internet.html
At the moment this is a placeholder for notes. The tutorial might have to be finished by someone who has more time than me to work on this device. Mine is on Verizon now. I will probably poke at it a little bit more when I get home and back to a normal schedule, but throughout December, it's going to be hectic for me. I'm going to try and add pictures so someone will have some knowledge going into this where I had none. If someone can get a hold of a Bionic tutorial, this might be similar.
Currently talk and text works but 3g data drops out. It works when it's connected but wants to cycle off and on A LOT.
As a good rule of thumb, always try to backup your settings before modifying them.
DIAG MODE
Verizon Droid RAZR Diagnostic Mode How To
NOTES (semi based off Thunderbolt tutorial)
CDMA WS 3.5 or later will give you more options and another method of writing data profiles to the device.
QPST does work HOWEVER you cannot read and then write the original settings to the phone (after modification of course). You have to start fresh and write ONLY.
CDMA AUTO (PRL) MODE (info from RLockwich)
Go into *#*#4636#*#* - Went into phone information (Set to CDMA Only PRL, DNS check allowed, Query CFU enabled).
QPST
Add the port for the device if required under QPST configuration. It's going to be the DIAG port. Just check device manager to see what port that is.
Use the Service Programming application under the QPST folder to access the phone. Connect to it but don't read.
Now follow this tutorial to write the proper information:
http://www.cricketusers.com/flashing...s-cricket.html
Write to the phone. Reboot it once all the writing is done and catch the boot to put it back in DIAG mode. If you don't it's no big deal, but you will have to power it down and get it back in DIAG mode before continuing.
CDMA WS
Open up CDMA WS and connect to the port with the RAZR. Go to the security tab and send the SPC 000000. Then go to the memory tab and send the DROID NV items which can be found at whiterabbit.org. It should write the NV items and fix the data.
UPDATE: The following might be required
Go to the "Other" tab and navigate to "R-UIM" then click read.
Change it to "NV Only" and write to phone. It should say Successful
Close out CDMA WS and reboot the phone.
Phone Settings (info from RLockwich)
Go into the ##PROGRAM select option 14 for LTE I turned off LTE bppanic, LTE Movement detection, and disabled Class 1,2,2 APNS
Additional Instructions (info from RLockwich)
Just went through all the settings again, I hope everyone can have as much luck as I just did. I was thinking, and I remember seeing the end of the thunderbolt tutorial says the last step is to remove the 4G LTE microSIM. I had tried that before early on when I first flashed it, but when I removed the card, it showed No Sim, no network connection and a SIM symbol with a exclamation point. I just tried it again a hour ago...Pulled the SIM, showed no network and then I rebooted the phone... FIVE times on and off all with immediate and STABLE 3G at 10 minutes a time between rebooting. FIXED. Done messing with it.
UPDATE 12/19 - After this last post it's been 4 days since we cracked the 3G cycling issue, and my phone is working excellent! I'm very glad I was able to be a part of this and get credit work any work I put into this.
Dina's Notes:
Got everything working THANKS to Chris and RLokwich! Oh, and for those of you that are not yet successful with this flash, just re-read the entire thread. Everything you need is HERE!
It was not all smooth in the beginning.
Insights:
1) No need for BP tools. If your phone is on the homescreen, just connect it to the cable, choose PC mode and set up the port in HW.
2) Mine took like 5 master resets before 3g showed up. So in case you are pulling your hair as to why 3g not showing up, master reset the phone. Turn on wifi. Bypass activation screen (backwards C method works if you keep trying for like 2 minutes), go through the set up pages and 3g will be there.
Everything is stable so far. 3g working like a charm.
Discovered a secret!
If you do not get 3g up, make sure to Enable at least one APNs in the LTE settings (##PROGRAM menu)
Now time for some icecream
Read more: Full Flash Verizon Motorola RAZR to Cricket Wireless (talk, text, MMS, and Internet)
MMS (needs to be tested)
The only thing I've realized now that is wrong, is no MMS. I have MMS through the tutorial on bypassing the apn through GoSMS, but I would very much like to not have it to be that way. I thought early on in this flash that I did have MMS, I think I was just being a smart ass so I changed some settings in ##PROGRAM for the SMS/MMS part that I copied from the Thunderbolt tutorial. I don't know if I messed something up. I was also thinking I've seen people having two Cricket apns? One for internet and one for MMS, does anyone know if that may fix it? I was thinking it may be that, but in my apn for cricket already, I edited it and filled in all the MMS settings for that APN. Maybe that's something I did wrong, I don't know.
If anyone does have working MMS on their flashed Razr, please post anything that might help us. Please post all your settings in SMS/MMS in ##PROGRAM and into your APN edit settings for Cricket APN you have for MMS (if you have anything filled out in the MMS blanks)
##Program
Enter SPC "000000"
SMS/MMS Settings
MML Server Name
[email protected] > wap.mycricket.com
Address for Upload to Online Album
438749 > 111111
Maximum MMS message size (Byte)
1228800 > 228800
SMS to Email Gateway
Anyone? Currently set at 6245
Try adding an APN for Cricket's settings or modifying the existing APNs to reflect Cricket's MMS settings.
Click to expand...
Click to collapse
can someoen please send me their email if they have a solution and i will pay for it!! i add esn's to metros inventory they dont accept ones with 99xxxxxxxxxx . any help would be appreciated
Bionic fully flashed and all working 100% but only 1g. Tried all the posted tips. Any
I fully flashed my bionic to cricket and everything is working 199% EXCEPT I only have 1G PERIOD!!!
ANY ideas?
Thanks
99 imei #
You have a 15 digit imei number correct?
Just remove the last number and google for a meid or esn converter
Enter your 14 digit 99 # and hit enter
you should get a 256 #
Smiles and good luck!