Hermes stuck boot mode - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??

rmorera84 said:
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
Click to expand...
Click to collapse
I had that problem and few more with my Hermes.
While it didn't help me, this suggestion by ultramag69 may help you...
Use the sd card method to flash a new rom, instead of a USB cable/Windows computer.
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
Hope this helps!

Just one other thing summoner, make sure you have Hard SPL V7 installed. Otherwise the ONLY rom I'd try flashing like that is the SHIPPED STOCK ROM. Its so the CID will be recognised and won't cause a brick.
rmorera84, unless you've installed Hard SPL V7 then find the SHIPPED STOCK ROM and flash that, anything else may permanently brick your Hermes.
If you have Hard SPL V7 (IPL 1.04, SPL 2.10 oli) then flash what you like...
Cheers...

- Installed latested Orange rom, that I know of - SPV_M3100_ROMUpdate_1007
- installed Hard SPL 7 & applied SIM unlock/super CID
- re-installed TNT TNT.19199_Professional_Hermes
The result is:
IPL-1.01
SPL-1.40.Olipro
I suppose I should upgrading the radio rom now!?
I am told don't try fixing what isn't broken - and it is working. 3G iNet, Phone, WiFi, BT - all good atm.
Or is there a particular update I should still install?
Thanks!

SUMM0NER, you're using an older, not so safe version of Hard SPL. The Hermes is downgraded to SPL 1.40 when you sim/CID unlock your phone. Best idea would be to re-install Hard SPL V7. Its a later version that seems less prone to problems when flashing.
Go back to the Hard SPL thread and get Hard SPL V7. I had the same thing happen to me when I unlocked the Hermes, nearly cost me my handset.
The steps are unlock Hermes, Install Hard SPL then upgrade OS.
Cheers...

Do I need to re-apply the OS rom file?
I just reinstalled Hard SPL7, now shows as IPL-104, SPL-2.10.Olipro.
Thanks!

My hermes only work whit this rom:Schaps_WM6Pro_ESN_3.54b-0808_Full
Because whit any other rom they stuck at 11%.
This is the info or the phone:
IPL-1.01
Spl-1.40.Olipro
Whit the first rom the htc boot but the phone funtion don´t work.

rmorera84, refer to my last post.
SUMM0NER, no. You have loaded the os, the reason you put Hard SPL V7 is if you want to upgrade the radio rom (not a good idea unless you are experiencing problems) or wish to change the os. Just means recovery is easier than if you didn't have it.
Cheers...

Many thanks ultramag69.
rmorera84 what branding is your Hermes (ie: Orange M3100, T-Mobile Vario 2, Vodeaphone V1605 etc...)?
Can I assume your Hermes is working right now?
If it is download and install HardSPL V.7 (attached to the bottom of the first post!)
Ones done verify that it installed correctly by holding the OK & Power button and pushing reset for a sec. The screen should display the coloured bars and say towards the centre: SPL-2.10.Olipro

It´s Cingular 8525, i could install the HardSPL V.7, now what rom i can flash??

You didn't confirm if it is working right now!?
If it is not working, try one of the official WM5 Cingular roms from this list. If that worked apply HardSPL 7 and take it from there.
Ones you downloaded the Cingular rom update you will have to keep unpacking the .exe files until you come to the actual .NBH file (WinRAR works for me).
Then follow ultramag69's instructions on flashing the rom via memory card.

Works, now i have this info:
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
I download the official Cingular WM5 rom, but. i don´t know how install this rom by memory card, could you help me??

Excellent!
Try downgrading to the Cingular rom via USB. Just double click the EXE and follow the instructions.
To use the memory card method follow these steps...
0. unpack the .exe file containing the rom with Winrar (right-click exe then choose "Extract to...\")
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
The reason to use the memory card to upgrade a rom, rather than a usb cable, is to cut down on failed upgrades (dodgy Windows/usb port/usb cable/etc..).
All working? Try upgrading to a Hermes rom that didn't work previously.

Any rom you can find in the Hermes section. Go to the WM06 part of the forum, theres a sticky at the top with about 50 older roms and you'll find other roms there too (latest is wm6.5).
Cheers...

i install the official WM5 AT-T version the WM6 AT-T, but, i still whit the no-gsm problem, can i flash i radio? or what i can do??

You may not be able to fix this, if you know what the original SHIPPED STOCK ROM was and can find it, then flash that. It may not work, if it gets stuck at 11% - 17% mark it means the radio ROM is stuffed and the memory area is corrupted. Not fixable.
You could also try, if you know what it is, the original radio rom by itself. Again, if you can't get it to work, you have a PDA but won't work as a phone ever again. Sorry to be the bearer of bad news.

Im to having the same problem, it keeps going back to the 2.1.Olipro boot loader.
I tried the memory card option and it starts to install but then stops.
Does anyone have and sugestions?
Cheers

Help Help
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..

Related

Error 260

Just got Hermes vodafone with German language and successfully loaded hardspl and have it in supercid. Now i want to upgrade to english version, but i keep getting error 260. PDA stays in RGB mode and saying USB. If i disconnect the cable it switches to Serial.
I have tried to update with
vodafone 1.20.161.6 aku 2.3
vodafone 2.07.161.1 aku 3.3
htc 1.35.255.102 aku 2.3
they all report the same. Have tried rebooting computer as said in wiki, but no success.
i now use original
HERM200
ROM 1.20.126.3
RADIO 1.16.00.0
any idea?
Thanks
Are you sure it is a supercid? Write the SPL, can you boot os?
Yes, i can boot os fine.
SPL-1.40.Olipro
IPL-1.01
I did supercid procedure with success....at least i thoughts so. It's my fist upgrade, so anything is possible. I used HTC Hermes SIM & CID Unlock - v3a
Thanks
I have the same problem with my second-hand JASJAM. The only way I can flash ROMs on my phone is by using RUUWrapper and select force SSPL and this always works well.
COME ON people!!!
A simple search would have remedied this...its been a topic so many times now!
The reason the official RUUs wont work correctly is because of the fact that HardSPL has been loaded, hence the SPL version isnt recognised, you gotta flash the official .nbh file using CustomRUU.
But first update to the latest version of HardSPL (see the sticky thread).
When you run the customRUU program select your SPL version (or use autodetect) and off you go!.
EDIT:: to get you started, Hardspl is HERE.....flash it.
then open the RUU with winzip or winrar and copy over the .nbh file into a folder.
download CUSTOMRUU.....run it from that folder with your device synced over activesync....select your SPL and voila.
Silly fella's. Its alright though I used to make the same mistake. I think im better friends with the search feature on here than I am with my real friends. You can always rely on the the WIKI or the search.
Thanks for help mrvanx i manage to flash with no problems now.
Promise to read more wiki next time
My problem was the same described in this post (too recent SPL).
I similar problem only difference is now phone wont go out of boot mode as its not recognised by active syn or in the rom update procedure.
Please help urgently cannot restore phone...and i dont know how
If you have Hard SPl V7 installed, try to re-install the rom, or a different one using the sd card method.
1. Format 2Gb or less sd card FAT32 and copy .nbh file onto it. Rename to hermimg.nbh .
2. Insert into Hermies and reset into bootloader, hold power, OK button under flywheel and reset with stylus hold all buttons in until you get to tri-colour (bootloader) screen.
3. Follow onscreen instructions...
Cheers...

Upgrading...

Hello,
I would like to upgrate Rom with this one: Schaps_WM6Pro_Hermes_4.31_WWE_Full.exe
I installed Hard-SPL and now I have 2.10.olipro SPL version displayed in the bootloader (before I had 1.4).
Actually, in my Hermes300 I have installed :
WM6.0
ROM: 2.54.258.2
ROM date: 07/06/07 (DD/MM/YY)
RADIO: 1.47.00.10
Protocol: 32.80.7020.20H
ExtROM: 3.54.258.102
I don't know if it is the original ROM upgrade from HTC website, because I'm not the firt owner of the phone.
Anyway, If I try to upgrade it by using autodetect mode an error occurs:"Error, Unknown version! You should pick safe SSPL".
Why? What Do I have to do to have Upgrade? Maybe, is there still some kinda of "brand"? Which option should I have to select?
I want to use the most safe upgrading procedure to avoid brick.
P.s. I'm using Windows Xp.
Thanks!!
Pick safe SSPL..... Follow the instructions after OR use the sd card method.
Format sd card fat32 then copy the .nbh file onto it. Rename it to "Hermimg.nbh". Put it in phone and reset to bootloader. Hold down power button, ok button above flywheel and reset with stylus. Hold all buttons in until you get to tri-colour screen. It should recognize the flash image so then follow the prompts.
Find this safer than pc flash.
Cheers......
Thank you very much I will do it!
But I'd like to understand why autodetect mode doesn't work! Do u hava any ideas? Cannot I choose SPL-2.02./2.10/2.30 New Bootloader and is it HARD-SPL choices? I'm a newbie in upgrading and I only understand that to avoi brick I should use HARD-SPL. If I use Force safe SSPL or SD card method can I have a brick?
How about if autodetect doesn't work because I have installed original ROM upgrade from HTC? It is possible?
Thanks.
No flashing method is a guarantee of success. Hard SPL isn't either, it just makes it easier or even possible to fix your phone. If you interrupt a flash you will brick your phone but with Hard SPL its possible to fix. Except if you interrupt the radio rom portion of the flash. I think its OK to say that if you stuff up this part of the flash you won't be able to fix easily, if at all.
Most, if not all, cooked roms DON'T have a radio rom inside. ALL stock roms do.
This is why I said its safer with sd card method. You would have to physically reset the hermes in the middle of a flash to stuff it. With the pc, usb cables can be unplugged, reset buttons can be pushed and blackouts/brownouts do occur. Thats if Activesync doesn't throw a hissy fit and disconnect while trying to update....
>HARD-SPL just makes it easier or even possible to fix your phone.
Ok, and by using SD CARD procedure is it the same?
I mean...now with HARD-SPL installed on hermes can I use every upgrading procedure to fix my phone (if possible)? Or to take advantage from that do I have to use a particular procedure?
Before writing here I read a post where another guy had my same problem and some people answered him to choose SPL-2.02./2.10/2.30 New Bootloader and is it HARD-SPL. But u think is better by SD CARD.... .
Thanks, and I'm sorry for many questions!
Does Schaps_WM6Pro_Hermes_4.31_WWE_Full.exe have a radio rom inside? I can upgrade only Rom without RADIO? If yes...how?
Thank you very much!
No, Schaps_WM6Pro_Hermes_4.31_WWE_Full doesn't have a radio rom. Look at the list of apps and tweaks included. It will tell you what radio version it has if it has the radio portion included...( this is for ANY cooked rom. The chefs work hard to make these and are rightly proud of their work.)
Here are the instructions for sd card flash again if you missed the first time
1). Format sd card fat32 then copy the .nbh file onto it. Rename it to "Hermimg.nbh".
2). Put it in phone and reset to bootloader - Hold down power button, ok button above flywheel and reset with stylus. Hold all buttons in until you get to tri-colour screen. It should recognize the flash image so then follow the prompts.
Its that easy when you have Hard SPL on your phone...
Cheera...
It worked very well. Thank u very much!
Sow if you don't have Hard Spl on your phone the SD flash method won't work? I have a spv m700 and coun't manage to install hard-spl.
Go to the last few pages of the Hard SPL thread - its a sticky - You'll find out how to install Hard SPL using the sd card method. Don't have to worry about sync errors with the PC then...
Cheers...
I have got Hard-SPL 2.60. Which one should I pick in the SPL Meny? I'm kinda noobish when it comes to this ...
I hope someone can help me , i ve tried a lot of roms, and i cant upgrade it, i also tried the sd flash , but it got stuck on the boot screen , could someone please help me, what should i do?

Help please!! unbrick htc hermes

My Htc hermes phone keep turning off and on after i upgraded it to rom 3.54.07.06. that i downloaded from a thread on this site. I did the Power+OK+softrest and got the 3 color screen its shows IPL 1.01 and SPL 1.40 Oilpro . and connected to my computer but my computer isnt snycing withmy phone or anything plz help me T~T
Welcome to XDA-developers.
The Hermes has a wonderful Wiki page for unbricking a device:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
You can also try to flash from the SD Card:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Though I'd try to upgrade the SPL(1.40) to Hard SPL V7 (2.10) first.
Try connecting the Hermes to the pc after 1st making sure to untick "Allow USB connections" in activesync, put the Hermes in bootloader and run the RUU_Wrapper.exe for Hard SPL V7. After this you should be able to use the sd card method to flash your Hermes with any rom. You used an early Hard SPL that is unsafe to try sd card flashing with... Live and learn...
Thanks very much your a life saver
i did it too
dear
yesterday i flash my hermes with hardspl v7
i get
HERM100
ipl 1.04
spl 2.10olipro
but i can"t flash original rom from sd card it only stuck at 0%
i try to unbrick my hermes because i get no radio and no gsm missing protocol and missing my imei
what kind of solution for me????
please help
SD card flash....
1. Format 2Gb or less card FAT32. Copy .nbh file onto it and rename hermimg.nbh.
2. Insert sd card into Hermes and reset to bootloader.
3. Follow prompts...
If you are using the unaltered ROM, the radio part may take awhile to flash - DON'T RESET... This may cause irrecoverable errors in the radio rom causing you to have a permanent brick...
Cheers...
This may not work, that means you're looking at a permanent brick. You may be able to flash an OS only rom on but you won't be able to use the phone anymore.

[Q] flashed a spl 3.5 rom into a spl 1.2 x7500, is it bricked?

I have flashed my x7500 before using the Athena_WM6_TMUK_2.35.110.4 rom and that worked. Bootloader said spl v1.0 so I tried the authenaunlocker which said it worked and from then the bootloader said spl 1.2 olipro
I then thought I could update to AGB v3.0 , it seemed like it worked but when it rebooted, it shows some mad pixels like a corrupt image and then seems to boot but with a black screen. I can hear it do the ping it does when it asks to calibrate the screen but it is entirely black :-(
I have tried an sd card method of loading a new rom but it always fails after a few seconds with red numbers 68002 and then goes back to the tri color boot loader.
I tried ultravanilla rom renamed to ATHEIMG.nbh in the sd card (formatted to fat32) and that does the same thing with the red numbers.
have I completely bricked it?
I should say that I'm on Windows 7 and I've tried the MAC change fix but the mtty app doesn't give me a usb port to select, just com1 and com2
I tried the windows exectuable for updating the rom but it always fails with error 244 invalid model id.
here's the images I see
[edit] hurray! the mtty thing worked after I found an old laptop that had xp on it to use, as soon as I had that I downloaded activesync , unchecked allow usb connections and fired up mtty, that had an entry for usb and then I just followed the instructions and was able to change the id, after that, I was able to use the windows exe rom update. I'm now back to where I'm started and have donated to cmonex!
hi i have the same problem with my t-mobile ameo.
the tri-screen even shows the same digits as yours.
did you manage to get a fix for it. or is it totally bricked
If you can enter the bootloader (tricolor screen) it should be possible to reactivate your Ameo. I have flashed my Ameo with wrong SPL ROM too (because it was labled as SPL 1.2 but is SPL 3.5).
If you don't have a WinXP system on your hand, try to flash with SD-card. You need a FAT32 MiniSD card (not SDHC!) or FAT32 MicroSD with MiniSD adaptor.
Format the card and copy the ROM file (for the right SPL!) to it, rename the file from RUU_Signed.nbh to ATHEIMG.nbh. Then go to the bootloader and the Ameo should be ready to flash the new ROM.
If you have a WinXP system you can try to enter the bootloader (remove the MiniSD card before) and then connect your USB cable. The bootloader should change from "Serial" to "USB" and should be ready to flash a new rom.
If your Ameo is fractious you can find some good tutorials here.
Purzelkater said:
If you can enter the bootloader (tricolor screen) it should be possible to reactivate your Ameo. I have flashed my Ameo with wrong SPL ROM too (because it was labled as SPL 1.2 but is SPL 3.5).
If you don't have a WinXP system on your hand, try to flash with SD-card. You need a FAT32 MiniSD card (not SDHC!) or FAT32 MicroSD with MiniSD adaptor.
Format the card and copy the ROM file (for the right SPL!) to it, rename the file from RUU_Signed.nbh to ATHEIMG.nbh. Then go to the bootloader and the Ameo should be ready to flash the new ROM.
If you have a WinXP system you can try to enter the bootloader (remove the MiniSD card before) and then connect your USB cable. The bootloader should change from "Serial" to "USB" and should be ready to flash a new rom.
If your Ameo is fractious you can find some good tutorials here.
Click to expand...
Click to collapse
hi I have the same problem this guy had, I have one question what rom should I use ? can you give me a link please
Purzelkater said:
If you can enter the bootloader (tricolor screen) it should be possible to reactivate your Ameo. I have flashed my Ameo with wrong SPL ROM too (because it was labled as SPL 1.2 but is SPL 3.5).
If you don't have a WinXP system on your hand, try to flash with SD-card. You need a FAT32 MiniSD card (not SDHC!) or FAT32 MicroSD with MiniSD adaptor.
Format the card and copy the ROM file (for the right SPL!) to it, rename the file from RUU_Signed.nbh to ATHEIMG.nbh. Then go to the bootloader and the Ameo should be ready to flash the new ROM.
If you have a WinXP system you can try to enter the bootloader (remove the MiniSD card before) and then connect your USB cable. The bootloader should change from "Serial" to "USB" and should be ready to flash a new rom.
If your Ameo is fractious you can find some good tutorials here.
Click to expand...
Click to collapse
it is not working...
keep your cool
the most important thing is to keep your cool, I've been in trouble before and managed to sucsses, first of all if you are able to go into bootloader you're fine, it seems to mi you flashed wrong spl, the AGB v3.00 is for spl 3.5 only and for what I understand you have spl 1.2, also i my experience you should work with win xp, i have my laptop with 2 os xp and 7, just to do rom loading on my 3 advantages, so if you are able to put your athena in bootloader plug it to your pc your athena sould change from serial to usb, if you can manage that you are almost done, now all you have to do is flash a compatible rom spl 1.2, if you still want agb v.3 you need spl 3.5 and the only way to achive that is to flash athena projet 4 rom, only when that is acomplished you would be able to load an spl 3.5 rom. I hope this help, keep us posted.
hi i have a pc on windows xp sp3 with htc 4.5 it does not pick up my phone bit it will try to load the windows 6 advantage rom,but after it reaches 2 percent ,the phone resets.i have done the same thing as above,i tried to flach a michy 3.5 rom over windows 6 on 1.25,i can get into bootloader but everytime i flash my phone resets.my mini drive is formatted,so could the problem be with the onboard sd card? if so in plain english could someone take me thru it step by step on hpw to access and format that,to see if it makes a difference,many thanks,and a nice contribution to anyone who can help me,and please if you start talking about hot keys,please state which ones,as every key is a hotkey many thanks curzie,if anyone ever needs pc or laptop advice pm me thanks
Who reflash device with this trouble ???
Working - or not ???
flash rom problem
hi, I'm in the same situation and sorry for my English, I have a X7500 I unlocked the radio, and then I installed the 3.0 rom agb all went well, but on the first reboot the system does not start, black screen, if I press the volume button turns on but displays the volume and the touch does not work, I can not make it go into bootloader because it turns on and remains on the flag!
Can you help me?
thanks
Solved
Check out my post http://forum.xda-developers.com/showthread.php?t=2172291

[Q] cannot uninstall HSPL, leoimg.nbh only with SPL2.08, address range SPL

Hi all
I have a memory problem in block 2405.
I want to send it to guarantee, but i can not set back SPL.
I have HD2 WWE, HSPL2.08. I can see white screen or boot loader.
I try this:
1. HSPL4.exe, HSPL3_PKG.exe are going well to end but they really doesnt change HSPL to SPL.
2. from original ROM I build leoimg.nbh and boot from SD but I see this
00018003
LEOIMG.nbh fail
radio_V2 fail
Rcust
Boot
Splash1
OS
Configdata
UPDATE Terminated
UPDATE fail
3. to flash original rom stop after 1% with memory fail
4. mtty task29 say that block 2405 is fail
1. have you any idea how to change HSPL into SPL
2. how to build leoimg.nbh only with SPL part? I extract 02_SPL.nb from original RUU_signed.nbh ROM
3. which address range in HD2 have SPL?
try using hspl2, and try to set 1.66 or 1.42. your current spl, 2.08, is a tmous spl, and can cause occasional issues with flashing stock from sd, even on a fully working phone.
ALso worth trying the freezer trick, too. Radio_fail is a fairly common fault, sometimes it gets fixed easily, , hspl works after several tries, or several attempts at flashing the correct stock rom from sd suddenly works, or chilling teh phone in teh freezer followed by an sd falsh suddenly takes and everything is fine again., , , but most times it doesn't get fixed.
I solve the problem
thanks
I try your freezer trick and hspl2,hspl3,hspl4 in all possibilities but doesnt change hspl.
BUT I found the list of Hermes boot loader commands. And I set task 2a. And this solve the problem with memory. After it is running flash from SD.
Ahh good to know.

Categories

Resources