im not a newby to flashing ive been through my tytn flashing left and right. i just got my fuze about a month ago and ive been reading evaluating all these roms to see which one would be best for me with the least amount of bugs.
i had no issue unlockin my fuze and by doing that i know i can go straight to flashing. but when i go to flash my fuze it gives me a Error Code 244 Device ID....i have no clue and am completely lost. any help?
I'm not familiar with that error code but do you have Olinex's HardSPL? If not download it and flash it to your Fuze, and then you may flash cooked ROMs.
PRETTY POSITIVE I DO BECAUSE I SIM/SECURITY UNLOCKED MY PHONE ETC...
will it hurt to flash hardspl again even if i already have it on here?
Nope, just do the HardSPL again...
read this: http://wiki.xda-developers.com/index.php?pagename=Elf_RUU_Error_Codes
Even though its for the elf the error codes will be the same
also when u enter boot loader, does the top white bar say "security unlocked?"
be very sure you hardspl properly by holding down bottom volume button and soft reset button at the same time. Top left should be 1.90 olinex. if not, you are not hardspl properly.
im going to just reflash hard spl. i know its flashed bcuz i unlocked the phone and thats part of the process. see what happens then. thanks for all the info
no luck. getting the same error 244 invalid device id
cediesaid said:
PRETTY POSITIVE I DO BECAUSE I SIM/SECURITY UNLOCKED MY PHONE ETC...
will it hurt to flash hardspl again even if i already have it on here?
Click to expand...
Click to collapse
That sounds really, really ominous. This is what error 244 says (thanks for the link, Warjcowski, it's an interesting read):
ERROR 244 (Invalid Model ID):
First reason: Your device is not CID unlocked, and the Model ID of your device does not match the Model ID of the ROM. CID unlock your device by flashing a Hard SPL and then try again, or flash a shipped ROM with the correct Model ID.
Second reason: You have the Hard SPL and are trying to flash a shipped ROM (which is attempting to overwrite the SPL). Flash a ROM that does not contain an SPL, or remove the SPL from this shipped ROM (i.e. use NBHextract.exe to grab all the components then rebuild just the OS.nb with HTC ROM Tool).
Third reason: You have the Hard SPL and are trying to flash an older (usually cooked) ROM. Downgrade to a USPL (different from Hard SPL!) using the 'white screen' method and then flash the ROM again.
Click to expand...
Click to collapse
That doesn't sound good. It makes me think you don't have hard spl. So I did a little poking around, and found this post from a thread that you started (emphasis mine):
cediesaid said:
i just got mine from sprint. im not a fan of the speaker volume. just doesn't ring as loud. i know with my tilt i found a way per this website to make it higher. not sure how to do it on my touch pro. can someone help?
Click to expand...
Click to collapse
In the first post, you said you had a fuze. You don't have a fuze, you've got a Sprint Touch Pro (unless you got rid of it and got a fuze-excuse me if you did). What ROM did you flash to your Touch Pro (probably Energy ROM, wasn't it?)? I'm afraid that you killed your phone.
excellent detective work Farmer Ted. I was going to go check to see all his posts as well to see what device he really had but you were ahead of me lol
i dont think ive killed my phone. im using it noe to reply. lol. i have not flashed any roms and im attempting. but i own fuze now
when you go into bootloader does it say? 1.90oilnex? i know someone said it before but i just want to make sure you have Hard Spl on there properly.
yes it did before i reflashed hardspl again. and it says it now too.....im sooo lost on what to do
cediesaid said:
im not a newby to flashing ive been through my tytn flashing left and right. i just got my fuze about a month ago and ive been reading evaluating all these roms to see which one would be best for me with the least amount of bugs.
i had no issue unlockin my fuze and by doing that i know i can go straight to flashing. but when i go to flash my fuze it gives me a Error Code 244 Device ID....i have no clue and am completely lost. any help?
Click to expand...
Click to collapse
What ROM (OS or radio; custom or stock) and what version are you trying to flash to?
cediesaid said:
i dont think ive killed my phone. im using it noe to reply. lol. i have not flashed any roms and im attempting. but i own fuze now
Click to expand...
Click to collapse
cediesaid said:
yes it did before i reflashed hardspl again. and it says it now too.....im sooo lost on what to do
Click to expand...
Click to collapse
Ok, now I'm really confused. In the first post, you say the phone is fine and you're using it to write the post. Maybe you're joking there-honestly, I don't know. But if it's fine, then why are you lost on what to do? Is the phone bricked, or is it fine? You can get into bootloader (I assume so, since you know that hard spl was flashed)? Then just flash your previous ROM back onto the phone off of an sd card.
im confused because i keep gwtting the same error message when i go to flash the rom
cediesaid said:
im confused because i keep gwtting the same error message when i go to flash the rom
Click to expand...
Click to collapse
Let's head back to the basics again.
What exactly and completely does it say when you go to the bootloader screen?
What is the model number of the device you are trying to flash?
What carrier do you have?
What ROM are you trying to flash?
What method are you using to flash this ROM?
My bootloader shows the following
Security Unlocked
RAPH110
SPL-1.90.Olinex
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
I bought my fuze form a corpoate att store.
I have tmobile and have been using my fuze on the tmobile network for about a month now.
I have tried flashing via usb with actie sync. and when it goes to flash it brings up the percentage bar saying it could take ten minutes and just go straight to 100 percent in like 2 seconds then gives me the error invalid device id.
the rom i was attempting was natv v4 for the fuze. then i tried the elite rom as well. no luck same result
received response
Just flash from your SD card assuming you have one.
Related
Ok, I give up. I've been searching all night and I cannot find an answer - all the answers that I have found seem to have driven me and my device further to a state that is unrecoverable.
First I couldnt update the rom at all because it crashed mid way, then I finally did get an OS up and running, yet with no radio - no imei or phone functions. I couldnt update radio rom, and I couldnt revert to the original. I now have just a boot loader, that I cannot install anything on to, at all.
"
HERM300
IPL-1.01
HERM300 MFG
SPL-1.01"
I know I'm running the wrong boot loader now, but it was in effort of persuing being able to update the radio rom. I'm following the instructions to change it and at "task 32" Im getting "FF"
Please. Someone help. I cannot be accused of searching first hand as I've been sat here since 7pm trying to sort this, its now 3:44.
Cheers.
you didnt change to hardspl boot loader before u tried to update it?
mien916 said:
you didnt change to hardspl boot loader before u tried to update it?
Click to expand...
Click to collapse
man, OP, please tell us you did...
have you tried reading here?
and here?
yes. and yes. Thanks for the quick replies - looks like im still up with it.
Bad times.. " you didnt change to hardspl boot loader before u tried to update it?" - this I dont understand. I've been following my nose all night. I've updated roms before, but i've never had any issues, certainly not like this.
Good times.. I've got it to boot. and I'm running WM6 "Pro Black" on the thing as we speak. so its not that dead..
I still have no radio version, nor imei, and spl/ipl is still 1.01. I'm trying to update radio rom, but it hangs at 0%.
i take it youve ruled out a bad usb connection? have you considered trying the SD CARD method of upgrading your rom?
thats all but ruled out, as i havent got an sd reader attached.
im making some headway, got the SPL at 1.10.Oli - still cant install radio rom though!
interesting. the shipped tmobile rom is now working...
I say working, its getting up to 13%. which is more than the 0 i was getting earlier.
Ok. So we're up to normal bootloader
IPL 1.04
SPL 2.10
No radio rom will install though. at all. error 262.
I have the same probleem with my t mobile vario 2. I can only upgrade OS ONLY rom, when I try to flash radio it freeze 0% error 262. I've tried evrything from wiki but nothing has worked jet. I hoop sameone can help us.. thanks
jacky651 said:
I have the same probleem with my t mobile vario 2. I can only upgrade OS ONLY rom, when I try to flash radio it freeze 0% error 262. I've tried evrything from wiki but nothing has worked jet. I hoop sameone can help us.. thanks
Click to expand...
Click to collapse
have you considered SIM/CID unlocking your phone? just a thought. not a definite solution. proceed with the latter (CID) AT YOUR RISK as ive heard changing CID to SUPER CID will make your device SUPER CID for eternity (?) and may void any warranty that you have..
bapski said:
have you considered SIM/CID unlocking your phone? just a thought. not a definite solution. proceed with the latter (CID) AT YOUR RISK as ive heard changing CID to SUPER CID will make your device SUPER CID for eternity (?) and may void any warranty that you have..
Click to expand...
Click to collapse
i 've unlock my phone couple month ago. it super CID i checked with 'mtty' info 2. i can flash everything except radio
Well I being stupid person that I was loaded Faria's rom without unlocking my G4 it got to 99% and errored saying update error and such. So i did some research finding out that I had to unlock first, now after reaidng some tutorials I see things about uploading the EnableRapi to my 8125 but problem is when I turn it on it only has the rainbow colors I can't get in to the phone and I can't use it..
Could anyone please help me and guide me or paste me a thread on how I can fix this. I've been researching for hours and haven't gotten anywhere. If anyone can please help me itll be greatly appreciated.
Thanks
All you have to do is put your phone in bootloader mode then flash wizard love or the rom that your device was shipped with.
You havent told us what wm5 rom your device originally had on it so we cant help you there but Wizard Love can be found here and here.
peter petrelli said:
All you have to do is put your phone in bootloader mode then flash wizard love or the rom that your device was shipped with.
You havent told us what wm5 rom your device originally had on it so we cant help you there but Wizard Love can be found here and here.
Click to expand...
Click to collapse
i've installed farias o1st wm6 rom on my g4 device using the shelltoll method..
i wanted 2 try nother wm6 rom
do i have 2 go thru the entire unlock process again or just use the shell tool with the new rom
ok
u hav 2 go thru the unlocking CID process again & everytime u want 2 reflash
Cingular 8125 G4
All seems to be working back to normal question though using the shelltools it doesn't display all the information about the phone when I press Get Info, i have a 2.x.0001 but when I press get info it wont show the info on CID or the option below it, but itll allow me to Extract OS, is that okay? or do if I flash it, it won't work?
aurfawce said:
All seems to be working back to normal question though using the shelltools it doesn't display all the information about the phone when I press Get Info, i have a 2.x.0001 but when I press get info it wont show the info on CID or the option below it, but itll allow me to Extract OS, is that okay? or do if I flash it, it won't work?
Click to expand...
Click to collapse
Unless the person who converted the 80040000-OS.nb to nk.nbf filled in those fields then they will be blank. Dont worry about these details. Flash away.
Good Luck
G4 help
so i tried flashing it I thought it was successful I did the hard reset after I ran the ShellTools. Was I supposed to do anything after the hardreset? Because I though then maybe I can go on to trying Faria's stuff but when I did got to 99% and 302 error occured so now im flashing back to old ROM, any hints? tips? or programs to make the G4 unlocking easier? any or maybe any roms out there you know of that won't mess with the SPL/IPL that I can just load the rom and use it?
Thanks
aurfawce said:
so i tried flashing it I thought it was successful I did the hard reset after I ran the ShellTools. Was I supposed to do anything after the hardreset? Because I though then maybe I can go on to trying Faria's stuff but when I did got to 99% and 302 error occured so now im flashing back to old ROM, any hints? tips? or programs to make the G4 unlocking easier? any or maybe any roms out there you know of that won't mess with the SPL/IPL that I can just load the rom and use it?
Thanks
Click to expand...
Click to collapse
So you tried to flash Faria's rom to a CID locked G4 then when that didnt work you used shelltool. Following this you tried to flash Faria's rom to your still CID locked G4 and it didnt work again?
I'm a bit confused so I'll start at the beginning again. If you do in fact own a G4 CID locked device then the only way that you can upgrade your OS is to use shelltool, unless you want to pay imei-check to unlock it. Using the RUU method to update a CID locked G4 will produce an error and not finish flashing or it will complete the flashing process but your OS will not have changed.
Shelltool doesnt unlock your device, it will still be CID locked after shelltool completes. Shelltool only updates OS so the chance of bricking your device is minimal. Hope this helps.
After flashing my locked T-mob vario dutch (for the 20st time) it now is bricked.
I tried to flash the Fun_Key_rom.
Hermes is stuck on the HTC logo 1pl-1.01 and SPL-2.03 not Super CID. (because of the warranty). I followed the thread about unbricking, but untill now no result.
I can flash it with Ruu.exe (and ruuwrapper.exe) the option 2.02/2.10 works for me untill 1% and then I get a invallid vendor ID.
I read the thread over and over again, but didn't seem to get how to unbrick it. Do I need to have a special rom? or other software?
no you need to flash Hard SPL on your phone right now!!! you can always unflash the HardSPL at a later date but you where just asking for a brick by not flashing HardSPL in the first place!
austinsnyc said:
no you need to flash Hard SPL on your phone right now!!! you can always unflash the HardSPL at a later date but you where just asking for a brick by not flashing HardSPL in the first place!
Click to expand...
Click to collapse
Had no problems for all those times..untill now I know it was stupid.
Trying to flash Hard SPL I got a 260 update error on the HardSPL v7. I also tried it with another upgrader and got an 270 error. It installed until 100% but no result.
marcoryn said:
Had no problems for all those times..untill now I know it was stupid.
Trying to flash Hard SPL I got a 260 update error on the HardSPL v7. I also tried it with another upgrader and got an 270 error. It installed until 100% but no result.
Click to expand...
Click to collapse
Yes, you need to use CustomRUU to avoid the invalid vendor ID. It bypasses the CID check. That is why it works, even though you are not superCID.
Regarding the 260 error, try a couple things.
If you can, try SD flashing.
If you cannot do SD method, try using "manual bootloader" method:
- Put phone in bootloader mode
- NOW attach to USB lead
- Start CustomRUU
If that does not work, try taking the battery out for a while (5 minutes) and then try again.
todd_jg said:
Yes, you need to use CustomRUU to avoid the invalid vendor ID. It bypasses the CID check. That is why it works, even though you are not superCID.
QUOTE]
Where can I get CustomRUU,Could'nt find it on XDA. Is it the same as RUUwrapper and RUUupdate?
Click to expand...
Click to collapse
marcoryn said:
Where can I get CustomRUU,Could'nt find it on XDA. Is it the same as RUUwrapper and RUUupdate?
Click to expand...
Click to collapse
It may be the RUUWrapper you have, but you can get it at THIS THREAD You may already have used it though, on the one that did not give you the invalid vendor error. Use it with the nbh file. If you only have an exe, then you can use winrar to take it apart into 2 files - the ruu file (the updater) and the nbh (the ROM itself). Once you are using the right CustomRUU, try the things I mentioned in my previous post.
Other things to be sure of...
If you are using Vista, check with MrVanx guides to see what you need to do.
You must have...
ActiveSync 4.5
.NET framework 2 or higher
Thanks for ur help. Really appr. it.
When I use the CustomRuu on any nbh file I'll get the Update error (260).
If I use the same nbh file on the RUU.exe file and I choose the 2.02/2.10 option it flashes my mobile till 1%. Then I get error 274 Invalid Vendor ID.
I see on the forum a lot of people bricked there Tytn on SPL 2.03.
Is Mr. Olipro having an solution?
Have you tried these things...
Code:
Regarding the 260 error, try a couple things.
If you can, try SD flashing.
If you cannot do SD method, try using "manual bootloader" method:
- Put phone in bootloader mode
- NOW attach to USB lead
- Start CustomRUU
If that does not work, try taking the battery out for a while (5 minutes) and then try again.
todd_jg said:
Have you tried these things...
Click to expand...
Click to collapse
Yes, but without any succes
marcoryn said:
Yes, but without any succes
Click to expand...
Click to collapse
What were the specific errors for each method? I know you cannot get 260 with SD card flash method.
marcoryn said:
After flashing my locked T-mob vario dutch (for the 20st time) it now is bricked.
I tried to flash the Fun_Key_rom.
Hermes is stuck on the HTC logo 1pl-1.01 and SPL-2.03 not Super CID. (because of the warranty). I followed the thread about unbricking, but untill now no result.
I can flash it with Ruu.exe (and ruuwrapper.exe) the option 2.02/2.10 works for me untill 1% and then I get a invallid vendor ID.
I read the thread over and over again, but didn't seem to get how to unbrick it. Do I need to have a special rom? or other software?
Click to expand...
Click to collapse
You are in a quite bad situation. I am not well aware about all the new ways to backup bricked hermes; but as far as I know the only remaining possibility for you is to flash your device using the default flasher AND a rom matching your CID.
Hopefully tmobile dutch released an updated WM5 release for your phone. You should be able to flash it, setup hardspl, and flash anything you want; but in a safe way this time.
There is maybe a way to tweak the CID of cooked ROM, but don't know anything about it (and there will certainly be signing issues).
In order to get your CID and see if something matching it is available at the wiki read the wiki about mtty (as far as I remember it is something like "type 2").
fun_key said:
You are in a quite bad situation. I am not well aware about all the new ways to backup bricked hermes; but as far as I know the only remaining possibility for you is to flash your device using the default flasher AND a rom matching your CID.
Hopefully tmobile dutch released an updated WM5 release for your phone. You should be able to flash it, setup hardspl, and flash anything you want; but in a safe way this time.
There is maybe a way to tweak the CID of cooked ROM, but don't know anything about it (and there will certainly be signing issues).
In order to get your CID and see if something matching it is available at the wiki read the wiki about mtty (as far as I remember it is something like "type 2").
Click to expand...
Click to collapse
Hope Olipro will release a CustomRuu version where 2.03 can be flashed. Lot of people have probs with 2.03. Dutch T-Mob haven't released anything there is no rom availeble.
What were the specific errors for each method? I know you cannot get 260 with SD card flash method.
Click to expand...
Click to collapse
I got another error on cooked roms (26008 or something) and when I put an org. carrier rom on the card it says checking but will not install because its not a legal rom.
Because of a hardware error I had to return my Tytn today..while it still is bricked. Hope Tmob will be kind and fix this for me along with the hardware issue
Hi,
I thought I did enough reading to hard-spl my g4 cingular 8125 but i guess not...
Anyways, I did the hard-spl and everything seemed to go smoothly. Then I went ahead and tried to flash the Touch no Evil ROM (http://forum.xda-developers.com/showthread.php?t=327215).
About 4% into the flash I got error 262: update error. Now the device is stuck on bootloader with IPL 2.21.0001 and SPL 2.21.01ip. Plugging in the usb shows "USB" at the bottom left corner of the wizard's screen but I cant detect the device in windows. Since I cant detect the device, I cant remove hard-spl and attempt to reflash using soft-spl the stock 8125 spl and rom.
Anyone have any suggestions on how to remedy the situation? Or did I just brick this thing
Any help or even linking to the right threads would be appreciated. A couple hours of searching didnt yield anything but maybe im looking for the wrong things...
Thanks,
Anushian
EDIT: More searching yielded this: http://forum.xda-developers.com/showthread.php?t=276963&highlight=stuck+bootloader
Basically use MTTY_updateROM.exe to dump the ROM onto an SD Card and restore from that? I dont have a card on me so Id rather get some input before going to buy one just to try this... Mainly, I need to know if the hard-spl still renders the unit CID unlocked and capable of preforming this method.
hello
i had the same problem and it seems its the Ruu i guess you used the ruu thats in touch no evil rom but your device is ok use the wizard love rom http://forum.xda-developers.com/showthread.php?t=298613 and then flash again with the tool that said in g4.7 and it works dont flash to original rom because it contains isp spl and can brick your phone i hope it helps.
Solidus_k said:
hello
i had the same problem and it seems its the Ruu i guess you used the ruu thats in touch no evil rom but your device is ok use the wizard love rom http://forum.xda-developers.com/showthread.php?t=298613 and then flash again with the tool that said in g4.7 and it works dont flash to original rom because it contains isp spl and can brick your phone i hope it helps.
Click to expand...
Click to collapse
Hi and thanks for the tip. I tried wiz love rom flash again and this time it worked (didnt recognize usb first time?). Anyways it went up to 6% and died since the battery died. Im going to just get a standalone charger and charge it and try again. Will probably take 2 weeks to get here though...
My main question is, based on the info provided, is the phone bricked or is it still repairable with a reflash? I didnt find much info related to hard-spl and restoring with the SD methods besides just that the phone must be CID unlocked...
Thanks!
if you have hard spl then you have cid unlock so your phone is ok if you flash wizard love rom use the ruu thats is in wizard love folder dont flash any official rom, try to change from computer or stop running other programs while flashing and your device is not bricked unless you intall official rom.
Solidus_k said:
if you have hard spl then you have cid unlock so your phone is ok if you flash wizard love rom use the ruu thats is in wizard love folder dont flash any official rom, try to change from computer or stop running other programs while flashing and your device is not bricked unless you intall official rom.
Click to expand...
Click to collapse
Hi Solidus_k,
Thanks so much for the info, much appreciated. I'll give it a go again as soon as my charger arrives in the mail since my batteries dead. Just wish you didnt have to boot into winmo to charge...
Anushian
Dear all,
I am facing a problem here.
Had a hardware problem with the built in microphone and had to revert back to stock rom/splash screen/Original SPL in that order.
Had no problems reverting the ROM and the original screen back (just a couple of flashes), BUT when I tried to revert back the stock SPL here http://forum.xda-developers.com/attachment.php?attachmentid=110582&d=1220406410
I renamed the file to RAPHIMG.nbh, copied it to the root of the SD Card and entered bootloader mode and this is what it displays:
RAPH100
SPL-1.90.0000 (Which means a successful flash)
!!! AND THEN THIS !!!
"Upgrade ROM code error"
"Please try again"
This message is located in the last part of the green stripe in the tri color screen (bootloader)
It is then followed by the grey screen automatically which you are supposed to press volume key to start a flash process BUT it just HANGS at Loading...
unabling you to flash anything.
It's actually a friend's phone too so I guess you understand how hard it is....
Any help is appreciated
Thanks in advance
Possible image might be corrupt on sd card, grey screen is shown when it's trying to read sd, have you tried with sd removed? if you get to 2nd tricolor screen with sd removed i would use usb flash to restore it to working order..
Da_G said:
Possible image might be corrupt on sd card, grey screen is shown when it's trying to read sd, have you tried with sd removed? if you get to 2nd tricolor screen with sd removed i would use usb flash to restore it to working order..
Click to expand...
Click to collapse
Removed the SD and it stays at the tricolor screen with the spl version as mentioned in 1st post.
Also, displaying the Upgrade ROM code error, please try again message
The mode is currently serial
What can I do from here?
fireblade63 said:
Dear all,
I am facing a problem here.
Had a hardware problem with the built in microphone and had to revert back to stock rom/splash screen/Original SPL in that order.
Had no problems reverting the ROM and the original screen back (just a couple of flashes), BUT when I tried to revert back the stock SPL here http://forum.xda-developers.com/attachment.php?attachmentid=110582&d=1220406410
I renamed the file to RAPHIMG.nbh, copied it to the root of the SD Card and entered bootloader mode and this is what it displays:
RAPH100
SPL-1.90.0000 (Which means a successful flash)
!!! AND THEN THIS !!!
"Upgrade ROM code error"
"Please try again"
This message is located in the last part of the green stripe in the tri color screen (bootloader)
It is then followed by the grey screen automatically which you are supposed to press volume key to start a flash process BUT it just HANGS at Loading...
unabling you to flash anything.
It's actually a friend's phone too so I guess you understand how hard it is....
Any help is appreciated
Thanks in advance
Click to expand...
Click to collapse
You cannot flash an SPL from the bootloader. You need to use SSPL. The directions can be found in the HardSPL thread.
NotATreoFan said:
You cannot flash an SPL from the bootloader. You need to use SSPL. The directions can be found in the HardSPL thread.
Click to expand...
Click to collapse
Hey man, thx for stopping by..
If I understand correctly, SSPL runs through the device which is stuck at bootloader currently... or am I hopefully wrong??
If you're at the tricolor screen and it reads serial, that should be fine.. plug in usb and it should switch to usb.. then flash a stock carrier rom through usb.. that should get you up and running and you can then run sspl and flash your spl
Da_G said:
If you're at the tricolor screen and it reads serial, that should be fine.. plug in usb and it should switch to usb.. then flash a stock carrier rom through usb.. that should get you up and running and you can then run sspl and flash your spl
Click to expand...
Click to collapse
Keep in mind im currently on stock SPL, do u think flashing the stock ROM is ok?
That's exactly why i suggested stock ROM, stock SPL will only accept stock ROM's (it will overwrite the spl too so make sure the stock rom you are using is the right one)
dude....i hate to say this...butyou might be s.o.l. at this point. i did the same to my fuze not too long ago... tryingto flash anything to the phone just locks it up.i was lucky enough to bs my way through an att guy to get me a new one (was still under the 30 day warranty).
Da_G said:
That's exactly why i suggested stock ROM, stock SPL will only accept stock ROM's (it will overwrite the spl too so make sure the stock rom you are using is the right one)
Click to expand...
Click to collapse
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
fireblade63 said:
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
Click to expand...
Click to collapse
I had the same problem as you and could not flash any rom, Always get Invalid vendor ID.
You need the right Stock Rom to flash and in my case in the middleeast, the Stock Rom is so far only available in at HTC.
I had to take the phone to HTC Service Center and they flashed the correct Stock Rom and charged me as they did it out of warranty.
Regards
fireblade63 said:
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
Click to expand...
Click to collapse
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
NotATreoFan said:
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
Click to expand...
Click to collapse
Hmm, then I need to know from which ROM the SPL originated and then flash it.
Thing is, some of the shipped roms available at wiki are just nbh files..
I tried flashing with the wrapper exe and the RaphaelCustomRUU.exe and still all roms I've downloaded don't seem to work.
It's a RAPH100 untied to a network.
fireblade63 said:
Hmm, then I need to know from which ROM the SPL originated and then flash it.
Thing is, some of the shipped roms available at wiki are just nbh files..
I tried flashing with the wrapper exe and the RaphaelCustomRUU.exe and still all roms I've downloaded don't seem to work.
It's a RAPH100 untied to a network.
Click to expand...
Click to collapse
Post in the HardSPL thread asking which ROM the SPL originated from. Once you know that, you can download the appropriate ROM from the Wiki.
NotATreoFan said:
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
Click to expand...
Click to collapse
SPL has nothing to do with the Invalid Vendor ID Error, It is the CID. In another word you can flash SPL 1.95 and still can not flash the AT Rom 1.95.502.5 because the CID is different.
Regards
ViperBJK's QMAT features GoldCard generator for current HTC devices that can force RUU to bypass CID check.
Do you know what is the CID of your device?
shafez said:
SPL has nothing to do with the Invalid Vendor ID Error, It is the CID. In another word you can flash SPL 1.95 and still can not flash the AT Rom 1.95.502.5 because the CID is different.
Regards
Click to expand...
Click to collapse
The CID is determind by the SPL.
Look up the error code posted... everything points to HardSPL. Back in my Wizard days, HardSPL did not exist, and we just did a CID unlocking. This is not the case with newer devices.
All ROMs are not created equal. Each WWE ROM checks for specific information within the SPL, and if it doesn't find what it's expecting, fail...
stepw said:
ViperBJK's QMAT features GoldCard generator for current HTC devices that can force RUU to bypass CID check.
Do you know what is the CID of your device?
Click to expand...
Click to collapse
I'm not sure
Where can I know that?
@NotATreoFan && Shafez,
I remember from TyTNII day when Shafez suggested extracting 3.29 and 28 SPLs from the newer shipped 6.1's for a better responsive device.
We could extract and build with htc rom tool if I remember the name of the tool correctly.
Do we have a tool as such compatible with TP? (agreeing with NotATreoFan here)
@Shafez,
Since you think it is not SPL and it is a CID issue, what can I do about it?
Sending it to SVC for repair out of warranty is an option but I'd like to leave it as my last.
Did they provide the ROM or they flashed it for you?
Were u able to make raw files out of it for future use or any1 else has it?
Thx guys and keep the help coming
fireblade63 said:
@NotATreoFan && Shafez,
I remember from TyTNII day when Shafez suggested extracting 3.29 and 28 SPLs from the newer shipped 6.1's for a better responsive device.
We could extract and build with htc rom tool if I remember the name of the tool correctly.
Do we have a tool as such compatible with TP? (agreeing with NotATreoFan here)
@Shafez,
Since you think it is not SPL and it is a CID issue, what can I do about it?
Sending it to SVC for repair out of warranty is an option but I'd like to leave it as my last.
Did they provide the ROM or they flashed it for you?
Were u able to make raw files out of it for future use or any1 else has it?
Thx guys and keep the help coming
Click to expand...
Click to collapse
Since you cannot get past the bootloader, your only option is to find the WWE ROM that matches the SPL you flashed. Even though the HTC ROM Tool "signs" the NBH file, it still won't fool the stock bootloader... if it did, we wouldn't need HardSPL.