I need help please..
after installation of several wm6.1 roms here,
my touchscreen isnt precise already.. it seems to be misaligned?
i always need to aligned the screen, but it dont work anymore..
whats wrong with my fone? is it because of the ROM or hardware error already?
thanks.
rizortiz said:
I need help please..
after installation of several wm6.1 roms here,
my touchscreen isnt precise already.. it seems to be misaligned?
i always need to aligned the screen, but it dont work anymore..
whats wrong with my fone? is it because of the ROM or hardware error already?
thanks.
Click to expand...
Click to collapse
BEFORE YOU RAISE YOU QUESTION,
1. did you make a search for an answer yet?
2. you need to provide details for you problems inorder to let other seniors here to help,
for example... which rom, how is the history....what had you done to it.......
ok ?
[QUOTE=..................
the same problem (i think it is the same) here..
it occurs generally while i am playing games and typing so many letters for sms's.
the problem has been existed since i have bought my prophet. the problem was there on official wm5 rom. using wm6 or 6.1 roms didn't fix it, but decreased a little (or i quit playing games so much).
since i couldn't enter the pin to unlock, two or more times i couldn't make an urgent call, then i soft reset it..
i thought that it is affected by heat changes when the battery consumption is high or when i hold it in my hand very long time. i also thought that it is a hardware problem, but not sure.
recently, i do not use my prophet so much, then it hasn't annoyed me for a long time..
sory,
i should have defined the problem mentioned above:
- when i touch a point on the screen by stylus (or any other way)
it assumes that i touch some pixels left of the point i intend.
- in a few minutes, sometimes this shift increases about one or two centimeters, sometimes it stay one or two letters left of the intended letter on a standard keyboard.
- this shift is much more on the right part of the screen, it gradually decreases towards the left side, and finally it exact macthes that your pressing point.
think of a rubber band, fix one end onto the left edge then stretch it to the right, this is the touch screen you see. release it to shrink it, now this is the way that it assumes you touch on it.
- after soft reset, generally the problem's gone, sometimes not.
- after re-aligning the screen, it's gone, but when somehow the cause gets remedy after a while, it occurs reverse way, then you should correct the screen alignment again (
screen misaligned
I have the exact same problem for years, I would say ever sice I got it. It's happens just like atakatas says.
Just something I noticed, It happens to me when I keep it in my leg pocket, and usually I don't soft reset nor realign the screen. I used to do that, but then I found out that waiting a few seconds it would get back to normal.
So I never asked anything arround here because it really didn't look like a software problem. I would say it is climate sensitive
Cheers
Related
I have a T-Mobile Pocket Phone Edition,
It's had a rough life but as kept going for over 3 years now.
For the last year I would have to realign the screen 2 or 3
times a week but over the last few months it keeps getting worse.
Sometimes the screen won't respond to anything anywhere,
then after I tap it a few times boom works fine.
Sometimes I'll tap on the “Ok” and the “Start menu” will activate.
Sometimes drawing a line up the center of the screen will end up
shooting all over the screen.
And sometime it will work perfectly!
I thought the problems were to erratic to be hardware so
I hard set after awhile it started again,
So I hard set and installed a different ROM after a coupe hours
the problem was back.
Also sometimes the align program will get stuck in a
loop that doesn't end.
I've searched but can't find an answer? Anyone have an idea?
I've already taken it a part once but couldn't see how to get
any further after I toke the back panel off? Please help!
WOW nobody? So no one was heard of this problem before?
Can anyone direct me to directions on taking apart the Wallaby?
Thanks <><
It's a problem with touch screen. You should check (and fix) it.
Maybe it is necessary to press well screen to the motherboard. (Sorry my english).
Ok, Can you tell me where that connection is?
Thanks
Toke everything apart, found the connection, cleaned everything (w/ screen wipe)
put it all back together. Still have the touch problem and now the backlight won't work!
I've found if I press the unit in my hand the touch panel works right,
I don't think it's a lose connection to the main board so I think it must be
one on the main board.
If anybody thinks they want it for parts let me know! :?
Hello all the wizards of this site!
I own a Touch cruise for abt 1,5 years. Have always been a fan of this site and used cooked ROM's from the very beginning. Now the problem with my device.
I took it from my pocket and put it on a table. Afterwards when taking the phone I had a missed appointment on my screen. Trying to dismiss it I noticed the screen didn't react to any touches. So at first I thought the device had hanged. Soft reset but nothing..I couldn't even dismiss the alert as the screen didn't react. That's the first time I thought the screen might be broken. So I did some research from the internet and found that a Hard Reset might help. Tried hard resetting but couldn't do it. I'm pushing the Internet Explorer and GPS buttons (lower softkeys) and pushing the stylus to reset button but nothing...just a soft reset. So I thought I'd install a new ROM as that should also erase everything from the devices memory...nothing. The new rom is installed but I'm now stock in the screen alignment Touching the screen doesn't work where the cross is..as I run my finger all across the screen it seems that lower left part is kind of responsive as the small cross moves when I touch the lower left part of the screen. Now I noticed that the screen has an oily line in the center of the screen...
so what am I to do? Screen broken? Why can't I hard reset then? The warranty of course is for 2 years but I'm quite sceptical if this goes under warranty..they can alway say that something has hitted the screen or smthng.
Any knowledge and help is appreciated..
thank you in advance
dep w/ broken device
check this out
hello depeche,
u might find your topic discussed here
http://forum.xda-developers.com/archive/index.php/t-475294.html
good luck
same happen to me on may, and i send it to htc. They replaced all the front of my polaris wich was scrached
My Raphael doesn't go forward from the align screen since I hard reset on Mystic 6.5 lite ROM. Now I have tried all stock ROMS with the same problem. I Will try to best describe the problem in a chronological order.
1. Had stock ROM latest with TF3D2
2. Flashed to Mystic ROM 6.5 lite, took three cycling of align screen to get through
3. After 24 Hrs lock screen got stuck, no sliding action worked,
4. Performed soft reset, phone boots up to lock screen again.
5. After several tries decided to hard reset
6. Normal boot up until Align Screen, The align screen markers keep rotating on tap, but doesnt pass through to home screen or customization.
The phone connects to active sync, and I can synchronize, flash roms normally.
I like to think that 6.5 ROM changes some screen sensitivity settings, and this is not allowing the screen to align normally. Somehow these settings could be stuck,
I request one of you experts to guide me in getting my expensive phone back. FYI, I have no warranty, I am not even in UK, I have purchased this phone over Ebay, I have flashed around 15 ROMs since my 2 month ownership of the phone, with no problems.
create an empty file called welcome.not and place it on your sd card then hard reset
welcome.not
Warjcowski said:
create an empty file called welcome.not and place it on your sd card then hard reset
Click to expand...
Click to collapse
Done that and it successfully skips the alignment section...but.....
It now recognises touches but The touch screen takes wrong inputs, some times it doesnt, how can I recalibrate, without going into align screen, or can I go there too??
Where do I go from here
sandandrocks said:
Done that and it successfully skips the alignment section...but.....
It now recognises touches but The touch screen takes wrong inputs, some times it doesnt, how can I recalibrate, without going into align screen, or can I go there too??
Where do I go from here
Click to expand...
Click to collapse
here are a few links and misc info. Unfortunately development was stopped since calibration wasnt perfect, but its worth a shot.
http://www.wmexperts.com/align-your-touchscreen-automatically
http://forum.xda-developers.com/showthread.php?t=473976
Cab location (post 45): http://forum.xda-developers.com/attachment.php?attachmentid=149596&d=1232741513
(post #48) Try editing this reg:
HCM\HARDWARE\DEVICEMAP\TOUCH\CalibrationData
values: 485,500 785,171 785,820 193,820 188,175
Hi, if the align screen markers are not accepting your input, it is more than likely something is interfering like a screen protector or case putting pressure on the screen. (or a digitizer failure)
the only reason it would not accept the inputs is if the data it's receiving is too far from the actual point of the crosses.. it makes you keep cycling through until it's within a level of tolerance..
Warjcowski said:
here are a few links and misc info. Unfortunately development was stopped since calibration wasnt perfect, but its worth a shot.
http://www.wmexperts.com/align-your-touchscreen-automatically
http://forum.xda-developers.com/showthread.php?t=473976
Cab location (post 45): http://forum.xda-developers.com/attachment.php?attachmentid=149596&d=1232741513
(post #48) Try editing this reg:
HCM\HARDWARE\DEVICEMAP\TOUCH\CalibrationData
values: 485,500 785,171 785,820 193,820 188,175
Click to expand...
Click to collapse
Thanks for that ready info, really appreciate it.
Though it does give me some promise, but as you know I cant use the touch screen accurately, so installing a cab or changing the registry is near impossible scenario, unless those can be done via a computer. Right now, wherever I click on the screen, the notification area comes up with battery, network strenght info etc.
Do you know of any way how we can clean up the entire TouchPro (waever it means) and make a new flash. I presume flash does that, but then again I think there is some leftovers from previous ROM, as mentioned in the "Flashing your first GSM ROM" sticky, where it is recommended to hard reset immediately after flashing.
All your help required to save the phone and my money going down the drain. It just hurts that I was so much in love with this phone, since using Wizard for 3 years. Cant bear to lose this fight.
Da_G said:
Hi, if the align screen markers are not accepting your input, it is more than likely something is interfering like a screen protector or case putting pressure on the screen. (or a digitizer failure)
the only reason it would not accept the inputs is if the data it's receiving is too far from the actual point of the crosses.. it makes you keep cycling through until it's within a level of tolerance..
Click to expand...
Click to collapse
Thanks DA_G for considering to help me overcome this.
At the moment I have no screen protector on, I had one on for two weeks, and as it wasnt a good fit and collecting dust underneath, I threw it out arnd 2 days back. I have always used the normal sleeve case from HTC.
If you say there is no other reason for this behavior other than hardware issue, then I have no options left. You mention that the digitizer may be broke, couldnt it be that the software part of the digitizer is broke and we can rectify that.
After using wizard for three years, and that too very roughly, I have like dropped it several hundred of times, and not facing a problem, I refuse to believe HTC quality has dropped down so low. This touch pro was used most carefully for arnd 2 months only.
I still ask you to give me more options before going for hardware replacement. As of now I will remove welcome.not, hard reset and try aligning as long as I can bear it.
hi you should be able to use the keypad to cycle through... is it? i use to have tytn II. so u can install the fix or do a reg edit with it.
gaiden said:
hi you should be able to use the keypad to cycle through... is it? i use to have tytn II. so u can install the fix or do a reg edit with it.
Click to expand...
Click to collapse
I have tried it with the keypad, unfortunately, it doesnt work as well as one would want it to ,,,,unlike the wizard I had.
The biggest problem you face here is to click the left and right soft key commands like OK, UP.
Wizard had the hardware keys for that as a fall back but not here.
I am at my wits end,.....wasnt that long!
Look up Pocket Controller @ Handango (it's expensive, but the demo's great). It allows you to run your ppc remotely. It has a pretty trick regeditor. It's a high octane version of active sync. You can probably align the screen with it (Settings>System>Screen). It shows you a big pic of your touch pro screen on your pc, and you can click things with your mouse.
Farmer Ted said:
Look up Pocket Controller @ Handango (it's expensive, but the demo's great). It allows you to run your ppc remotely. It has a pretty trick regeditor. It's a high octane version of active sync. You can probably align the screen with it (Settings>System>Screen). It shows you a big pic of your touch pro screen on your pc, and you can click things with your mouse.
Click to expand...
Click to collapse
Well I didnt try that but I used the My Mobiler, well the catch is you cant align your screen using these softwares, you can do all rest, install cabs everything, except align screen.
I believe the hardware digitizer has given up on me, I have just dropped it at the service center, who will ship it to another one, then they will quote for the repairs. So i keep my fingers cross until next week and see how they try to rip me off.
Did you revert to stock rom, radio and spl before you took it in? I hope so.
Farmer Ted said:
Did you revert to stock rom, radio and spl before you took it in? I hope so.
Click to expand...
Click to collapse
I reverted to only stock rom and radio, not the SPL.
As it is I havent given it in warranty, so I assumed it wont effect either ways.
It's weird you started having the problem after you removed the screen protector. Why did you remove it? Did it come off easily, or did it stick a little and give you problems? Do you think you might have messed up the screen when you were taking it off?
Farmer Ted said:
It's weird you started having the problem after you removed the screen protector. Why did you remove it? Did it come off easily, or did it stick a little and give you problems? Do you think you might have messed up the screen when you were taking it off?
Click to expand...
Click to collapse
I dont think that my removal of screen protector could have hurt the screen. As it is the screen protector was stuck on loosely.
The protector I had was a little hard kind and thick kind as opposed to the usual thin layer. I really didnt like it.
I am still of the opinion that WM6.5 rom had changed the sensitivity or some other parameter of the screen to an extent where the hardware couldn't cope. As I first faced the problem with align screen repeating 3 times when I installed that.
Within 24 hrs my digitizer had given up on me. Hence I think, if I the ROM can be completely sanitized and then flashed, the digitizer should work.
I am in no way an expert on these things, but I am just trying to apply some logic.
T Mobile MDA IV Screen Calibration Data
Can some owner of TMobile MDA IV mobile give me the screen calibration data from the registry.
It can be found at
HKLM > HARDWARE > TOUCH > CALIBRATION
I will be most thankful
HTC Fuze Alignment issue
Okay I have an HTC Fuze right, and I did a hard reset on it because the touchscreen was freezing, and working in only certain parts of the screen, so now Everything seems good with the touchscreen except the align screen part.. itwon't let me go past this stage, and Ive been at it for 2 days so can someone please help me out with my issue, I would sincerely appreciate it and thanks.
Dude, there is nothing much that you can do. There are ofcourse ways to skip the calibration screen and get to the desktop, but the functionality of the screen is allready gone.
If you are lucky enough to have a warranty for the thing, its time to use it now !!! If not, then start budgeting for a new phone.
As I didnt have a budget, I am using the phone in this condition since around a year and now thinking to replace it with Nokia N900.
Hi to everyone in this forum. I've recently received as a present a new toshiba folio 100, but, since I'm experiencing an annoying menu button flashing, I've thought of it as a software problem so I upgraded the folio using the foliomod1.3c and applied the rotate patch and also the 1.3c fix patch. The menu still flash with no apparent logic. I've tried to kill all applications running and it's still there. It seem to come up and down at random. I ask to all in this forum: do you believe it's a hardware issue or is a software issue? Because if it's a hardware issue I'm going to try to have a new folio from toshiba. I'm overall very pleased with the work that Dexter made to make the folio an usable machine but this flashing is driving me crazy. I use the folio basically as a portable scientific pdf reader so I need to concentrate on what I read and this flashing is really annoying. I would like very much to thank you all in this forum in advance for all the suggestion/help you could provide.
use my "foliobuttons" app
teknoraver said:
use my "foliobuttons" app
Click to expand...
Click to collapse
I have a request that serve All those who suffer MENU crazy button .
Is it possible to prepare application you can setting ON/OFF the MENU button
Most of the time useless button.
sometimes button jump after 10 minutes, sometimes after an hour
Usually I fix the problem by changing the settings with FolioButtons 1.1.
If you could add to FolioButtons on/off operation for menu Buttons was the best.
Hi teknoraver,
Can you add enabled/disabled menu button in foliobuttons application ?
flashing on...
teknoraver said:
use my "foliobuttons" app
Click to expand...
Click to collapse
I am pretty desperate about this issue, because none of the methods seem to help...
Right now the buttons work opposite- Menu button flashes mad and none of the other 3 responds...dont know how it happened
Just a thought- while the folio is booting up the menu button ALREADY flashes! I have zero understanding in there but isn't it a process that loads / starts early in the line?
I appreciate everyone's effort trying to solve this bug as it makes this handy tool a useless pile of crap.
I was wondering how many folio users are suffering of this crazy buttons madness.
Mine was crazy from the very beginning; I sent it back for repair and toshiba only did a firmware restore... Nothing changed at all!
It makes my folio almost unusable!
bye bye crazy buttons
After two weeks of testing and a complete breakdown of my folio100, I finally find the problem or just crazy buttons and freezing of the screen.
I drag a thickness in the screen in the bottom right corner of the screen to isolate the audio connector and it works better than a miracle again.
The only downside is that the screen comes out slightly from the slot but nothing really bad.
The thickness I put slightly too big or-1.4 mm I'll Demount next week to put a finer and I'll try to take pictures in passing.
Note however that the loss of waranty is innevitable.
Sorry for my bad english ;-)
I think it's a hardware issue and even a build quality issue.
If i hold my folio at the side of the buttons, i get the flashing buttons problem (even the foliobuttons app will not help), if i hold it at the other side, i've got no problems at all.
Do you have an animated background? Because I saw that some people had this issue with an animated background...
Hi Mshr73, nice first post indeed
Could you post some pictures of what you did?
Mshr73 said:
After two weeks of testing and a complete breakdown of my folio100, I finally find the problem or just crazy buttons and freezing of the screen.
I drag a thickness in the screen in the bottom right corner of the screen to isolate the audio connector and it works better than a miracle again.
The only downside is that the screen comes out slightly from the slot but nothing really bad.
The thickness I put slightly too big or-1.4 mm I'll Demount next week to put a finer and I'll try to take pictures in passing.
Note however that the loss of waranty is innevitable.
Sorry for my bad english ;-)
Click to expand...
Click to collapse
seems to get better...
I really don’t want to be too quick on this, but Dexter’s 1.4 seems to bring relief to this issue - for 2 days I have been running this mod the menu button stopped flashing!!
Any similar impressions on this?
vietnamibalzsam said:
I really don’t want to be too quick on this, but Dexter’s 1.4 seems to bring relief to this issue - for 2 days I have been running this mod the menu button stopped flashing!!
Any similar impressions on this?
Click to expand...
Click to collapse
No way pal, I guess I'm in the opposite situation. It still happens to me, and sometimes I think it even got worse... well, I can always look at crazy keys as a "special feature" that no other tablet will have!!!
I just tested without thickness under the screen, with foliomod 1.4 and after a few hours I again the problem of crazy buttons.
Mshr73 said:
After two weeks of testing and a complete breakdown of my folio100, I finally find the problem or just crazy buttons and freezing of the screen.
I drag a thickness in the screen in the bottom right corner of the screen to isolate the audio connector and it works better than a miracle again.
The only downside is that the screen comes out slightly from the slot but nothing really bad.
The thickness I put slightly too big or-1.4 mm I'll Demount next week to put a finer and I'll try to take pictures in passing.
Note however that the loss of waranty is innevitable.
Sorry for my bad english ;-)
Click to expand...
Click to collapse
Well, I just finished dismantling e reassembling my Folio. Following your hint, I cut a piece of paper and put it between the audio connector and the back of the screen (yes, it was metal vs metal). I'll see whether it's gonna work or not. Crossing fingers for now.
Not that I'm so confident in leaving a piece of paper stuck right where the DC input is .
BTW, did you try with a smaller thickness? Even if this is the problem, I'm wondering whether a piece of paper would be enough or not.
thyself can someone. post pictures of before and after details?
we will be much appreciated
i didn't have the crazy buttons issue this far in 2 weeks, just my home butten needs to be pressed harder. I'm pretty sure it's hardware related, i read often that users experience it when changing from an warm room to a colder one, or in regions where its verry humid(some circuit closes maybe...). so Mshr73 is on the right way as far as i can tell.
Dexter's 1.4
^Sbk79^ said:
No way pal, I guess I'm in the opposite situation. It still happens to me, and sometimes I think it even got worse... well, I can always look at crazy keys as a "special feature" that no other tablet will have!!!
Click to expand...
Click to collapse
Really sorry mate, I hope it will solved this for others too...
Anyhow, it is so disturbing, that I was already considering to send the tablet back to Toshiba...
I'll try to do this weekend if I do not have too many customers. I post the result Monday.
Mshr73 said:
I'll try to do this weekend if I do not have too many customers. I post the result Monday.
Click to expand...
Click to collapse
I'm looking forward to your pictures, too... because my trial simply didn't work.
I tried with both a single piece of paper and then with 2 pieces wrapped in tape. I put these spacers between the back of the display and DC/audio connector.
In both cases, the crazy keys phenomenon started to happen after 15-20 minutes of usage.
In most cases, it starts to show when I unlock the device. As soon as I unlock it, home and menu buttons light up with no apparent reason and go crazy for 10-30 seconds.
Then, I even tried to loosen just a little the screws (I read, somewhere in the forum, of a guy who said that he solved his crazy keys and screen lag problems this way). I mean, all screws are now locked but not too tight. Well, I have to say that I don't have any screen lag anymore (I even removed the piece of paper, from the battery area, which used to solve the issue before) but crazy keys still happen. I'm going slightly mad
^Sbk79^ said:
I'm looking forward to your pictures, too... because my trial simply didn't work.
I tried with both a single piece of paper and then with 2 pieces wrapped in tape. I put these spacers between the back of the display and DC/audio connector.
In both cases, the crazy keys phenomenon started to happen after 15-20 minutes of usage.
In most cases, it starts to show when I unlock the device. As soon as I unlock it, home and menu buttons light up with no apparent reason and go crazy for 10-30 seconds.
Then, I even tried to loosen just a little the screws (I read, somewhere in the forum, of a guy who said that he solved his crazy keys and screen lag problems this way). I mean, all screws are now locked but not too tight. Well, I have to say that I don't have any screen lag anymore (I even removed the piece of paper, from the battery area, which used to solve the issue before) but crazy keys still happen. I'm going slightly mad
Click to expand...
Click to collapse
Well ... with a piece of paper the problem Come back.
I handed a piece of cardboard and the problem disappears.
I think that to raise the screen to solve them but I'm still not 100% sure.
So, this thing drives me crazy...I've tried everything I knew and still nothing solved this problem.
I'm using HTC One. About 10 days ago weird things with touch started to happen. It seems that touch is partly unavailable/unresponsible on touch in one or two small areas. It seems to me like theres an empty place on my touch. Visualy is everything fine. Screen is crystal clear and has no damages or scratches. But I can't slide icons without troubles. Somwhere on 1/4 of screen, touch brakes briefly and I need another try to slide the icon. The same thing happens with status bar on the top of screen - I can slide it until that 1/4 part and it stops there and goes back. If I slide it quick with short move, it works fine, just slide alone over problematic area.
Also, few times I had that problem where screen works things on itself will. Makes pictures, or adds filters on Instagram, or, I don't know, just jumps around for few secons. Then, I lock the screen, then unlock it and usually that calm down the screen.
Also weird thing is that, when I want to send message, I can't reach "send" button in first try. I have to drop down writing sheet, than to touch the letters to put it in writing mode again, and then I can click the "send" button. On the same place where it was previously!
At first, I thought that plastic case or PVC protection is the problem, so I took off the protector from the screen. That solved problem for a bit. Then, I put back screen guard, and problem came back. After I totally rejected screen guard, problem is still here. I've tried to reset phone on factory, but that wasn't helpfull...
I forgot to state that I'm using Android 4.2.2 and this started to happen after that version update. I had no problem before.
So, now I'm here, as I don't know what else to do before I take this beauty to service. I just hope that this happens because of software bugs :crying:
Is there anyone who could help me? Have similar problem or know how to fix this?
In the meantime, I'll just hope that 4.3 will fix it themself... :fingers-crossed: