When my contract was up and I was trying to decide what new phone to get (upgrading from a RAZR), I did a lot of research online. I was looking for something that I could easily mod, customize, and program. In the end (partially because of these forums ) I decided to buy the Fuze.
So I finally got around to modding my Fuze, and it was a success and a lot of fun! I hope this post can help someone like me who wants to customize his/her Raphael - this is what I did, and how I did it.
As you read, refer to the Links, Downloads, and Notes sections below!
1 - Backed up Data.
Used PIMBackup (A,1) to make a backup file of my stuff, and used ActiveSync(bluetooth) (2) to copy everything to my laptop.
2 - Dumped Original ROM. (B,C)
Used PHM RegEdit (3) to change HKLM\Security\Policies\Policies\00001001 from dword:2 to dword:1
Did a soft reset.
Using ActiveSync, copied "itsutils.dll" to fuze:\My Documents\
Using Total Commander (4), moved itsutils.dll (5) from fuze:\My Documents\ to fuze:\Windows
While connected via ActiveSync(bluetooth), the following "pdocread.exe" (5) commands were run from Command Prompt:
Code:
"pdocread.exe -l > pdocread_dump.txt"
[Using the output from pdocread.exe (look for the hex offsets of each of the four disk parts)]
"pdocread.exe -w -d DSK1: -b 0x800 -p Part00 0 0x31f000 Part00.raw" (3.12 MB in ~10 seconds.)
"pdocread.exe -w -d DSK1: -b 0x800 -p Part01 0 0x480000 Part01.raw" (4.50 MB in ~15 seconds.)
"pdocread.exe -w -d DSK1: -b 0x800 -p Part02 0 0x9ba0000 Part02.raw" (155.63 MB in ~20 minutes.) (*I)
[Changed ActiveSync from bluetooth to USB]
"pdocread.exe -w -d DSK1: -b 0x800 -p Part03 0 0x12800000 Part03.raw" (296.00 MB in ~6 minutes!) (*II)
Using WinRar, RRU_signed.nbh was extracted from Stock Raphael RUU 1.90.405.1 (6,*III).
Installed RaphaelKitchen v0.62 (E,7,*IV).
"RRU_signed.nbh", "Part00.raw", "Part01.raw", "Part02.raw", and "Part03.raw" from above were moved into RaphealKitchen's "BaseROM" folder.
3 - Cooked Original ROM. (C) (To keep the original ROM - just in case).
Ran "RaphaelKitchen.CMD" from Command Prompt. (Key commands: e,b,<Enter>,c,a)
BuildOS opened automatically, and the green "play" button was clicked. Once it was done, it was closed and RaphaelKitchen continued.
Back in RaphaelKitchen, <Enter> was pressed.
The hex editor "XVI32.exe" opened automatically to show the newly created *.nbh file. Once it was closed RaphaelKitchen continued.
Back in RaphaelKitchen, <Enter> was pressed.
HTC Tool opened automatically, checked the new file, said everything looked good, and closed automatically.
Back in RaphaelKitchen, <Enter> was pressed.
4 - Flashed Hard-SPL. (E)
Downloaded "RaphaelHardSPL-Unsigned_1_90_3.zip" (8).
Ran "RaphaelHardSPL-Unsigned_190_1_3.exe" while connected via ActiveSync(USB).
After going through the prompts on the phone and the laptop, the screen went black on the phone.
After ~1 minute, the progress bar jumped from 0% to 100% and the phone turned back on.
Did a soft reset into bootloader mode (by reseting the phone with the volume-down button pressed).
Tri-Color screen comfirms the SPL was flashed: "SPL-1.90.OliNex".
5 - Flashed a Cooked ROM. (F,G,*V)
Downloaded NRGZ28's "EnergyROM 3.0 RAPHAEL 20090605 Standard" (H,9) and extracted with WinRar.
Removed SIM and SD cards, rebooted the phone, and connected to ActiveSync(USB).
Ran "Custom_RUU.exe".
After moving through the prompts, the phone restarted and showed the Tri-Color screen.
A grey/blue progress bar on the phone mirrored the progress bar on the laptop.
The process finished after ~10 minutes, and the phone rebooted into the new ROM!
Once the "align screen" dialog came up, the phone was Hard Reset (reset while holding volume-down and enter).
Another grey/blue progress bar showed the restore progress. It took ~20 seconds.
Volume-up was pressed, and the Fuze booted up with the fresh new ROM!
The Fuze was turned off, the SIM and SD cards were reinserted, and the Fuze was booted.
And it worked - this is awesome!
I'd like to give a huge "thank you" out to everyone here at xda for sharing your knowledge and creativity! I would have never been about to figure this stuff out without these forums.
And special thanks to:
mskip for the excellent guide on Flashing for Noobs
RezzZ and jcespi2005 for showing How to Dump a ROM
jcespi2005 and JugglerLKR for the Raphael Kitchen
OliNex and the Raphael Elite Team for Hard-SPL
NRGZ28 for the very slick EnergyROM 3.0
And many others who have posted here that I can't remember at the moment!
Thanks again, and I hope this helps.
-Undefined
Downloads:
1: http://rapidshare.com/files/191036103/PPCPimBackup2.8__run_from_phone_.exe
2: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center-download.mspx
3: http://www.phm.lu/Products/PocketPC/RegEdit/
4: http://www.ghisler.com/pocketpc.htm
5: http://www.xs4all.nl/~itsme/projects/xda/tools.html
6: http://rapidshare.com/files/1389803...d_Raphael_CRC_52.33.25.17_1.02.25.19_Ship.exe
7: http://www.4shared.com/file/67398870/5d504a33/Raphael_ROM_Kitchen_v062.html
8: http://forum.xda-developers.com/attachment.php?attachmentid=108649&d=1219714334
9: http://energy.wub.nu/ROMs/Raphael/EnergyROM 3.0 RAPHAEL 20090605 Standard.rar
Links:
A: http://forum.xda-developers.com/showthread.php?t=448008
B: http://forum.xda-developers.com/showthread.php?t=419036
C: http://forum.xda-developers.com/showthread.php?t=427507
D: http://forum.xda-developers.com/showthread.php?p=2453788
E: http://forum.xda-developers.com/showthread.php?t=410150
F: http://wiki.xda-developers.com/index.php?pagename=HTC_Raphael_Cooked_WM6.1_ROMs
G: http://wiki.xda-developers.com/index.php?pagename=HTC_Raphael_Cooked_WM6.5_ROMs
H: http://forum.xda-developers.com/showthread.php?t=517296
Notes:
*I It would probably (definitely) be faster (when backing data up) to use ActiveSync via USB instead of bluetooth.
*II When using ActiveSync(USB), don't let the Fuze go to sleep; it will disconnect ActiveSync!
*III Don't run the RRU_Raphael...exe file! Just extract "RRU_signed.nhb".
*IV The password for RaphealKitchen is in "!!!readmefirst!!!.txt".
*V Deciding which ROM to install can be tough. This ROM was chosen because of it's putative speed and WM6.5.
Nice job.
Should help many newcomers get a sense of the process required.
Cheers,
Wouldnt be a bad idea to add this to the Wiki...
Agreed ... maybe even add it to the Useful Links Thread.
Nice summary all in one post.....
Related
I'm truly sorry about the delay.
I've finally got round to posting a a STAR100 SuperCID guide.
1. Get itsutils: http://www.xs4all.nl/~itsme/projects/xda/tools.html
2. Run pdocread.exe with no args. Take a note of the "uniqueid" value.
3. Run "pdocread -n 1 0x000000 0x10000 -b 0x4000 original-bdk1.nb" - you'll get a file.
4. Head over to http://www.spv-developers.com/strtrkCID/. Feed it the DOCID and the file you got from steps 2 and 3. It'll give you back anoter file.
5. Run "pdocwrite -n 1 patchedfile.bin 0x000000 0x10000 -b 0x4000" where patchedfile.bin is obviously to be replaced with the patched file you got from step 4.
6. There is no 6. Report feedback.
Click to expand...
Click to collapse
All credit goes to itsme - he wrote all the tools and scripts which made all this possible.
Spawning script: perl startrek_cidedit.pl cid1e62995dd1db197b00b697388760b5e3.bin -i DOPOD601 -c 11111111 -o supercid1e62995.bin 2>&1
decrypting
bufend=44bdd4609845fd0931a871b4a31ddba42d4b96386f9 e9c5dff947c035432fc15
result=b2c7c4eede400853eb232eba436f394b3d75a9adf4c e9a1e452b26ea9059dc59
sha64k=8a7e3a8462b8c851ac125710d44abc05da4916f215e 331f98420db7ae5d87a5d
buffer checksum failed
why ?
Looks like the DOCID value you entered is incorrect. It should be a long stream of hex numbers.
Fantastic !!! Working Ok on SPV F600. Now, we need how to simunlock this smartphone.
Thank you very much Zone Mr.
i run pdocread in step 1 and got a dos screen that desaper in a second,and were i find the file in step 2.
Zone-MR said:
Looks like the DOCID value you entered is incorrect. It should be a long stream of hex numbers.
Click to expand...
Click to collapse
thank you Zone-MR,can u tell me how to get a long stream of hex numbers.
wlinsong said:
thank you Zone-MR,can u tell me how to get a long stream of hex numbers.
Click to expand...
Click to collapse
i know how to do,thank Zone-MR very very much
is there someone know how to flash rom use T-flash Card?
someone can't get the docid ,because you must use the old one!
I tried to do first step but when I ran pdocread.exe I get the following message :
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart activesync
or maybe your device is application-locked.
I've app-unlocked my device, activesync works ok, and restarting does not help. Phone is Qtek8500.
Any ideas?
Thanks
Is the script to calculate CID area for startrek available?
I think this should use the same method on Artemis or Herald, the problem is that they have G4 DOC and we'll not be able to use pdocwrite, but on those phones we're already able to place a hacked SPL in mem with psetmem.exe and jump into it's address with modified haret version. If we have the right CID area we can use the hacked SPL to flash it.
sorry for the ignorance...
I have downloaded itsutils but where is the dpocread.exe??
do I have to connect to the device with the mtty??
Maybe a bit more explanation
I've CID unlocked my Qtek 8500 and installed new ROM 3.6.251.0. Thanks Zone, great work!
Maybe it would be useful to write more detailed instructions, so here it is :
1. Application unlock your phone using regeditstg and do the following :
HKEY_LOCAL_MACHINE\Security\Policies\Policies\0000 1001 = 2 -->Change the value data from 2 to 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\0000 1005 = 16 --> Change the value data from 16 to 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\0000 1017 = 128 --> Change the value data from 128 to 144
Reboot the phone
2. Run SDA_ApplicationUnlock tool. Reboot the phone after it finishes.
3. Download itsutil.zip from http://www.xs4all.nl/~itsme/projects/xda/tools.html , version from 2005-6-28. There is even newer version, but with that version you can not use pdocread without arguments.
4. Connect the phone with activesync
5. Run Command Prompt, go to subfolder named "build" in itsutils folder, and run pdocread without arguments
6. Note the value of "uniqueid". It will be something like : "00 00 00 00 12 03 02 14 3b 07 1b b2 04 05 07 54"
7. run pdocread again with these arguments : "pdocread -n 1 0x000000 0x10000 -b 0x4000 original-bdk1.nb". This will make original-bdk1.nb file in build folder (where the pdocread is located).
8. Upload this file and value of uniqueid to http://www.spv-developers.com/strtrkCID/. It will open a new page after few seconds. Go to bottom of the page and click the link "Download patched BDK1"
9. Download the file (it will be named like "supercidxxxxxxx.bin) to "build" folder
10. Run the pdocwrite from command prompt with these arguments : "pdocwrite -n 1 supercidxxxxxxx.bin 0x000000 0x10000 -b 0x4000". Replace supercidxxxxxxx.bin with the original name of downloaded file from step 9.
11. Wait 15-20 seconds and that is it. Reboot the phone and install the ROM you like
It works! I've got now 3.6.251.0_02.67.30 on my Qtek!
Thank's, damird, your guide is unreplaceble for such lamers like me
But maybe anyone can suggest me were can i find and how to install (if it possible) Russian t9 or only russian lang to input? Or maybe how to rollback to original ROM with this that lang... (1.02.261.1)
Thank's
added:
Problem's gone, Russian T9 added.
Damird!
Cheers mate
Hello, can you share with us this script to calculate CID area in StarTrek?
With this script we can SimUnlock the StarTrek very easy (at least I think...)
Thank you very much.
I'm confused here... is CID unlock not the same with SIM unlock?
my carrier is tmob but I'm getting cing 3125 at ebay so I need to SIM unlock the phone for it to work on tmob right?
wow, pof, I can't wait for it! i had bought one herald in China but wireless was disable by default. I hope I could unlock the CID and get a WWE rom to enable the wireless.
sokelut said:
I'm confused here... is CID unlock not the same with SIM unlock?
my carrier is tmob but I'm getting cing 3125 at ebay so I need to SIM unlock the phone for it to work on tmob right?
Click to expand...
Click to collapse
Correct, you still need to pay to carrier unlock the phone. Check the wiki for links to a few services that are known to work.
CID unlock? Error installing ROM
I'm getting an ERROR [294] INVALID VENDER ID
I did the CID unlock
It starts to install the rom but when it gets to 4% I get this error. How do i fix this?
Can anyone help?!
Need a little clarification
Im stuck in steps 3-11. I've downloaded itsutils and I don't know how to proceed.
I'm trying to use the RBMC command in the BL to extract the splash screens (as I couldnt find Orange-Israel splash screens anywhere).
I authenticated myself in the BL (btw, I have an exectuable that will do all that is written in POF's wiki). when I use the RBMC command:
rbmc d:\splash.nb 500e0000 40000
alot of garbge starts to flow to the screen in MTTY.
I guess MTTY doesnt saves the file automaticly.
Please help me dumping the Splash using this method (or any other method)
Capture the output with usb-monitor and convert it to binary file.
Pog, can you elaborate in this?
I used USB Monitor to log everything. Now I have a HEX and ASCII dump of every packet that cam from the TYTN. How do I save it into something usfull and how do I convert it to binary and then to BMP?
You can do it with unix command 'xxd' (included in vim) or with a simple C program (do a bucle in a shell script for every hex-char):
Code:
int main () {
unsigned int c;
unsigned char aux[10];
int s=read(0,aux,4);
sscanf(aux,"%x",&c);
printf ("%c",c);
return 0;
}
If you don't have access to a linux box, attach the dump here and I do it for you.
damnit, I wont have access to linux until next week...
I would appritiate your help in converting but I dont know if I did the dump correctly with USB Monitor.
First, it has several packakets with the commands I issued, than it has several LARGE packets with "junk" (I think thats the Splash screen dump).
However, I can export it to TXT and in TXT I see both the HEX and the ASCII part. Is that ok? If not, how do I dump the correct part?
knfevg said:
However, I can export it to TXT and in TXT I see both the HEX and the ASCII part. Is that ok? If not, how do I dump the correct part?
Click to expand...
Click to collapse
Yes this is correct. Attach the dump and if it is useful i make the splashscreens for u.
POF, attached is the zipped file with the TXT dump (in unicode).
It would be GREAT if you could help me.
If there is a need in some other kind of a dump, please let me know.
The dump is incomplete, you only dumped 24Kb, a whole splash screen should be at least 128Kb + 128Kb more of padding. Attached is the partial bin file.
mtty is not good for rbmc'ing... the best is to use linux 'cu' comand (included in uucp) like this:
Code:
((sleep 2 && echo rbmc file 500E0000 40000 ) | cu -l /dev/ttyUSB0 ) > dump.txt
POF,
I think I've attached the wrong file
I hope thats the correct one
there you go, splash in .nb and .bmp
pof said:
The dump is incomplete, you only dumped 24Kb, a whole splash screen should be at least 128Kb + 128Kb more of padding. Attached is the partial bin file.
mtty is not good for rbmc'ing... the best is to use linux 'cu' comand (included in uucp) like this:
Code:
((sleep 2 && echo rbmc file 500E0000 40000 ) | cu -l /dev/ttyUSB0 ) > dump.txt
Click to expand...
Click to collapse
Hi pof.
Have tried this too, but the dump.txt contains only 46 bytes. What's wrong.
mm... post the contents and we'll know
Probably it's failing because you have to authenticate to the bootloader prior to doing the rbmc command (or use a patched SPL which does not require it, for example latest HardSPL).
Pof, THANKS!!!!!
One more question.
The secondary splash is usualy the same as the prime?
What IS SubMain splash? When does it come up?
knfevg said:
The secondary splash is usualy the same as the prime?
Click to expand...
Click to collapse
Generally yes.
knfevg said:
What IS SubMain splash? When does it come up?
Click to expand...
Click to collapse
MainSplash - the one you see with the red letters at bottom when booting
SubSplash - the next one without red letters
If MainSplash and SubSplash are the same, you get the feeling that there's only 1 splash screen, but there are actually two
pof can you make me .bmp from dump?
I can xxd to hex but don't know what's next to got .bmp
Thanks
gromel said:
I can xxd to hex but don't know what's next to got .bmp
Click to expand...
Click to collapse
After you xxd the hex, the binary file you get is the actual splash.nb, so you can use nb_image_converter.exe to make a BMP, you can find it here:
ftp://xda:[email protected]/Hermes/Cooked_ROMs/Hermes_SplashScreen_Pack.zip
BTW, before using xxd you'll need to convert the dump from utf-8 to ascii.
If you can't manage to do it yourself, tell me and I'll do it for you.
Ah, now better understand.
But When I try iconv -f utf8 -t ascii dump -o output
then I got always error iconv: illegal input sequence at position 0
PS. In usb-monitor I can export as UNICODE or ANSI (ASCII).
I'm trying and trying and trying....
Ok guys,
i think i'm in a sort of big trouble. I got SPL1.2, i was installing this Miky ROM and then at 91% Windows Mobile Device Center crashed on my pc. Now what i have is a 7500 booting with strange lines on the screen and then fading to white. I tried to pull out the battery and then to recover but nothing is working. I broke my 7500??? Why God is never here when i need him???
See if you can get into bootloader (tri color screen) if you can flash a factory rom. Have a look here, you should find what you need or a link to the needed resources http://forum.xda-developers.com/showthread.php?t=429013
Cheers
BR
***Why You Try This !!!___carefully step by step !!!!!!!!
cmonex
Senior Member Join Date: Jul 2006
Location: Budapest
Posts: 2,314
--------------------------------------------------------------------------------
here's an experimental program I made to make the process more automatic so users can fix their own wifi without our help.
this is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.
STEP BY STEP:
1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
NOTE, the command starts with a lowercase "L", not "I"!
WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx
13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.
edit: see raskell's mtty tutorial too, #36. post in this thread
if you *really* can't manage to get it working, you can still feel free to PM me.
let me know if this program and step by step description helped any.
Attached Files mac1.zip (6.3 KB, 1585 views)
mtty_0513_Test.zip (553.9 KB, 1883 views)
__________________
Here is direct link__on floor #33 ===>
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Good Luck!!!
Hello
Please help me return the model number,
cause when I try to change my rom I always get the same error Error [244] : Invalid model id.
Now I have
some strange symbols in bootloader.
This appeared after I'd tryed to change mac using mtty, as I have created bin file for SPL 1.xx
Please help me
Hi,
You need to carry out the instructions to the letter in post 33 HERE and it will sort your problem, read it all very careful, its easy to make a mistake if you're not paying attention.
regards
Jay
Thanks Jay.
It works again.
You're welcome, glad it helped
Regards
Jay
here's an experimental program I made to make the process more automatic so users can fix their own wifi without our help.
this is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.
STEP BY STEP:
1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
NOTE, the command starts with a lowercase "L", not "I"!
WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx
13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.
edit: see raskell's mtty tutorial too, #36. post in this thread
if you *really* can't manage to get it working, you can still feel free to PM me.
let me know if this program and step by step description helped any.
Attached Files
File Type: zip mac1.zip (6.3 KB, 2125 views)
File Type: zip mtty_0513_Test.zip (553.9 KB, 2613 views)
Ameo
Pfff i have tried everthing what i could find and nothing works. i managed to get the driver working from usb on windows 7 but it keeps showing the bootloader! with some strange marks. i flashed it with 1.2 Olipro and im afraid it will never work again any suggestions left?
Greetings
I would ask all active members to upload or share their collection of roms for Hurricane. I bricked my hurr 2 years from now and yesterday i got one so i would like to try as many roms as possible, and it will be great for all to share roms!!! I found several on this forum (lazaj's, saleng's, shadow's) but i think that there is more!!! So share your collection!!!
Here i found some on forum:
hurricane unlock, patch and upgrade wm 6.1(selang09) ***
Link: http://www.megaupload.com/?d=JLO5H1L7
Thread: http://forum.xda-developers.com/showthread.php?t=475286
Opinion: Good one, but chinese language everywhere! After u change main lang. still some apps name stay in chinese and options too!
wm6.1 for hurricane (with Bluetooth and INFRARED RAY problems solved)0415update!!!
Link: http://rapidshare.com/files/100934508/5x6_wm6.1_0319.rar
Thread: http://forum.xda-developers.com/showthread.php?t=378607
Opinion: Didn't tried!
WM 6 Graphite rom, how to get WMPlayer in English (now in Polish)
Link: http://rapidshare.com/files/108676266/wm6_2_2.zip
Thread: http://forum.xda-developers.com/archive/index.php/t-384972.html
Opinion: Using this one right now! Seems ok, works nice, nice look, except incoming calls didn't show up!!! Very bad bug!
Wm 6.1 Pl/eng
Link: http://rapidshare.com/files/131860280/wm_6_1_by_Lazaj007.zip
Thread: http://forum.xda-developers.com/showthread.php?t=410739
Opinion: Tried before Graphite eng edition, works great, looks great... Main lang polski, after lang change WMP stay in polski! But still ok!
WM6 for SPV C550
Link: http://rapidshare.com/files/56833250/566.zip
Thread: http://forum.xda-developers.com/showthread.php?t=330709
Opinion: Never tried!
And one pack with SPL 1.00.84 & soft spl (nb, nbf), IPL 1.00.15, GSM DATA (hex and dec), bootloader commands, splsplit... etc!
Link: http://rapidshare.com/files/427352270/data_hurricane.rar
Info: This last files can help u to unbrick your hurricane (BUT AVOID TO BRICK IT), i found it on pda2u.ru , and thanks them for that! Special thanks to member SAXON!
I found many links for ROMs but those which is here have alive links! Someone with good upload speed can reup them again in one pack and post a link here!
ENJOY!
I would like to have a non T-Mobile German version (can be a shipped ROM). Have not found any yet, only those that are available at www.shipped-roms.com Have to live with de-branding this as it seems.
Possibly someone with any of the following devices can do a "r2sd all" backup of the ROM?
imate SP4M
Orange C550
Qtek 8200 (the Russian/English is available as RUU)
Thanks for this link tobbbie !
Btw, in selang's rom SMS Send don't work! So, it is useless!!! :S
I have tested all ROM´s below for SDA II, but for me lazaj007 is the best of all
Thanks to lazaj007
Did anyone care to pick up some ROM cooking for that device? I did not succeed in getting the .BIN files manipulated correctly - and I think I have a collection of nearly all ROM tools now :-(
howto convert .bin to .nb0 and back
Foreword:
.BIN files are not all the same by their nature (of course not by content). There are
.bin that are used to identify the bare binary content of the various partitions (you mostly see those)
.bin that are used to flash a ROM to the device. This looks somehow historic though, the format is already described by itsme at: http://www.xs4all.nl/~itsme/projects/xda/wince-flashfile-formats.html. It seems to me that some non HTC devices are still using this format.
The osnbtool.exe (from Weisun at PDACLAN.COM) does not work for any purpose regarding .bin files
at least not for Hurricane.
- The -sp option cuts only the B000F\0a header but does not reconstruct the blocks of the .bin file.
Mind that small .bin files (smaller than 0x1c00000) are treated correctly as there is only one block.
- The -2bin option creates an incorrect .bin header (sets a weird total length) and sets totally confused
block-load addresses for the created blocks of 64k (0x10000) size. Check it with viewbin.exe if you like.
Reference for the filestructure by itsme:
http://www.xs4all.nl/~itsme/projects/xda/wince-flashfile-formats.html
The splitrom.pl (itsme romtools) seems not be able to read the content of any .bin file I have fed to it.
Neither for .BIN files created for Hurricane nor those for Typhoon, I always get:
cmd> splitrom.pl <binfile>
B000FF image: 82040000-84c40000, entrypoint: 00000000
!!! your rom is not known to me: md5: a520f0d1093b36f0a3cfd9323ea99155
this bootloader seems to be No bootloader present
no xipchain found
no bootloader found
no operator rom found
no bitmap found
I am rather sure it should handle everything correctly but I am too stupid to debug .pl :-(
So the only thing that works and will re-create a flash-able .BIN file from a .nb0 is listed below:
convert .bin to .nb0:
enter: viewbin -r <binfile>, you get something like:
Image Start = 0x82040000, length = 0x02C00000
Record [ 0] : Start = 0x82040000, Length = 0x01C00000, Chksum = 0x00000000
Record [ 1] : Start = 0x83C40000, Length = 0x01000000, Chksum = 0x00000000
Record [ 2] : Start = 0x00000000, Length = 0x00000000, Chksum = 0x00000000
Start address = 0x00000000
The above has two blocks of data and a termination block.
The checksum = 0 effectively disables upload checking (so potentially dangerous).
The size just fits the Hurricane's SPL "l" (load) command buffer, as you get when loading a ROM:
"clean up the image temp buffer at 0x8C080000 Length 0x01C40000 "
The blocks can be smaller than 0x1c40000 but not bigger obviously.
then convert to nb0, enter: cvrtbin.exe -r -a <imgstart> -l <length> -w 32 <binfile>
for above viewbin output: cvrtbin.exe -r -a 82040000 -l 2c00000 -w 32 <binfile>
mind to omit the 0x for the start and address, replace <binfile> with your filename, then you get a resulting file from <original-name.bin> to <original-name.nb0> which can further be decomposed and edited with standard ROM tools
convert .nb0 to .bin:
enter: xipbin.exe <input.nb0> <start-in-nb0> <output.bin> <loadaddress>
to get back something flashable like above: xipbin.exe <input.nb0> 0 <output.bin> 82040000
mind to omit the 0x for the loadaddress, replace <"file"> with your filenames
to recheck if the created BIN file is usable, startup the viewbin again
enter: viewbin -r <binfile> you now get something like:
Image Start = 0x82040000, length = 0x02C00000
Record [ 0] : Start = 0x82040000, Length = 0x00040000, Chksum = 0x0208CC79
...many entries deleted...
Record [175] : Start = 0x84C00000, Length = 0x00040000, Chksum = 0x0177FB3C
Record [176] : Start = 0x00000000, Length = 0x00000000, Chksum = 0x00000000
Start address = 0x00000000
Done.
Looks quite different - but this is ok! The loading process in MTTY indocates the loading of each above block with a sequence of |*, so with these many blocks the upload to the device is giving feedback and thus is not tempting people to interrupt it.
I have done my tests with the 566.zip linked in the first post of this thread, but this should work with any .BIN file from the other ROMs as well. So I will continue to see if I can recycle any of the WM6 Roms for inserting my imgfs created for Tornado. As before the imgfs still the XIP is loaded and I know too little about this yet (especially in connection to the imgfs and how close these two are linked) - I am prepared to see non booting device states quite a lot. Luckily there is nothing done to the early boot chain (IPL and SPL) so I can always get back to the bootloader and start over again.
I hope to get a first indication that imgfs is mounted correctly in the "old" XIP before I have to replace the OEMdriver parts in my Tornado ROM.
I just checked if I can still use this flash-method for the Tornado - and it works as well. So the created "os-new.nb" in the OUT directory can be converted to .BIN and then flashed inside MTTY with the "l" command. Not that I like this method - but it works as well.
Tobbbie, you have here a very good research! To bad this device is out of use!