This morning I ran the battery dead in my 8525 which I have done several times through out its life.
I get home and plug it in and hold the power button waiting to see the wm6 boot image from the rom I use. No go
All I get is the try color screen reading
Herm100
IPL-1.04
Herm100
SPL-2.10.Olipro
I can get it to switch between serial and usb. Did I corrupt the wm6 rom? Are there any tricks to try to get it to load wm6 one more time to dump my contacts? Can I manually dump the whole rom and pull it apart to get to my contacts?
I have removed the battery and let it sit but on re-inserting the battery it goes directly to the boot loader again.
I have tried the OK - Power - stylus reset button combo and just the stylus reset.
I am searching the forums and google trying to find something but maybe someone has a tip I have overlooked.
I went ahead and tried to flash a new rom from the bootloader and it goes 100% completes and just goes right back to the tri-color screen...
I also tried flashing Hard-splv7 and received a communication error.
Not really sure what to try next if flashing a new rom doesn't help.. Anyone got any suggestions?
OK I attmepted the type 2a brick recovery listed at
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem4
Grabbed a copy of nuettyconsole and connected successfully to the phones loader console.
Ran both
set 14 0 and set 16 0
Both writes to the nand are successful but it still only boots back to the bootloader.... I am running out of ideas.
I have attempted to replace the radio rom but I continue to get a communication error.
Anyone have a link to a full stock rom with both radio/os?
I went ahead and flashed a full AT&T stock rom with both radio and wm6. The flash completed and the phone booted into the stock rom like it should. YAY!
The phone customized itself and rebooted only to get stuck right back into the bootloader loop...
Is there something wrong with the nand chips or did I just corrupt the bootloader by chance?
Anyone? Any Ideas?
Ok, finally got some time to work on this phone a bit more. I would like to get it working which I sorta have. Flashing a full(radio/rom/extended) HTC hermes_WWE rom from a xp desktop will get the phone to boot.
When the phone customizes itself it'll reboot and its random if itll reboot properly. Sometimes I have to hard reset the device or pull the battery then I can usually get the phone to boot back up and be completely usable. So I know the phone itself works with sms, 3G data, 3G voice, wifi, bluetooth and seems to run like the day I purchased it.
At this point if I attempt to reflash a cooked rom to the working phone itll finish then drop into the bootloader and will refuse to boot using any tricks until I finally reflash using the full HTC hermes_WWE rom. I was thinking that the bootloader itself became corrupt so I reflashed sspl 2.10 but that did nothing except stopping the rom from loading and leaving me stuck in the bootloader. I have tried the bootloader console access and used commands set 14 0 and set 16 0 to try to force the bootloader to load the OS on reboot all to no avail.
So where should I go from here... what would be stopping my phone from being able to load a cooked rom? Should I reflash the radio? Has anyone heard something like this?
Ok, I decided to get into the boot loader and start dumping everything I can to try to decide if this was a corruption issue. You will notice some strange stuff and if I try to run the command "rbmc" the boot loader flips out spewing garbage for 2 or 3 minutes until finally returning an out of boundary error.
Cmd>task 32
Level = 0
Cmd>info 2
HTCSSuperCID HTCE
Cmd>info 3
HTCSH
Cmd> info 4
HTCSCWS__001Ùü¤HHTCE
Cmd> info 6
HTCST ÚÈÒHTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.10.Olipro
Built at: Apr 22 2007 13:32:26
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1900
Partition[2], type=0x25, start=0x3200, total=0x1F900
Partition[3], type=0x4, start=0x22B00, total=0x17D00
CE Total Length(with sector info) = 0x4675800
CE CheckSum Length(without sector info) = 0x4560000
Lol I might not be of much help. But seeing as noone responded to all of your 5 or so posts. Try getting a new battery, something might've happen to it ?
Related
Please help me!!
I have tried all the systems described in the wiki without turns out to you.
Could you tell us which device do you have?
- HERM 100 / 200 / 300
- IPL & SPL versions
- Previous rom you had installed
- Language
And paste the output of these Bootloader commands:
Code:
info 2
info ?
checkimage
Model is Herm100 O2 XDA Trion German Language update to WWE (xxp://xda:[email protected]/Uploads/Hermes/CHT9000_ENG.exe)
I do not succeed to load nobody rom stop all to the maximum to 25%
I have tried all the ways also making to leave pda in boot mode
How them I must send those commandos through tty?
Put the device in bootloader mode (SIDE OK + POWER + RESET), connect it to the computer though USB cable, open RomUpgradeUT.exe and start the upgrade process, if it fails, do not disconnect the device from USB and start the upgrade again.
If that fails, download mtty.exe, open it, select USB, click OK, and type in the bootloader commands I told you in my previous comment.
For more info look at the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
No upgrade!!
info is:
info 2
HTCSO2___102"qŒ)HTCE
info ?
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19800
Partition[3], type=0x4, start=0x1C800, total=0x1E000
CE Total Length(with sector info) = 0x39E4000
CE CheckSum Length(without sector info) = 0x3900000
checkimage
IPL CRC checksum = 0x68F14038
SPL CRC checksum = 0x3BF03635
CE CRC checksum = 0xB17AD2A4
ExtROM CRC checksum = 0x1B80FFB9
Radio Image CRC checksum = 0xEF2E0780
----------------------
Tanks
Emblema said:
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
Click to expand...
Click to collapse
This seems not good to me
I guess you can boot the currently flashed rom and use the device, but you cannot flash a new rom, right?
Emblema said:
IPL CRC checksum = 0x68F14038
SPL CRC checksum = 0x3BF03635
Click to expand...
Click to collapse
Your IPL & SPL checksums are different from mines, which IPL & SPL versions do you have? The version numbers are shown on the device screen when you put it in bootloader mode.
pof said:
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
This seems not good to me
I guess you can boot the currently flashed rom and use the device, but you cannot flash a new rom, right?
Click to expand...
Click to collapse
yes I use the dispoditivo but I do not succeed to load one new rom
Emblema said:
IPL CRC checksum = 0x68F14038
SPL CRC checksum = 0x3BF03635
Your IPL & SPL checksums are different from mines, which IPL & SPL versions do you have? The version numbers are shown on the device screen when you put it in bootloader mode.
Click to expand...
Click to collapse
Herm100
IPL-1.00
Herm100
SPL-1.04
its possible to try to put within pda a rom dumped from an other? (.raw)
if, like?
Help me, my pda is 1/2 dead
Not possible at the moment. I think you'll need to format the flash or try to repair it using the bootloader, but I don't know the exact commands. I'll have a look at it and try to find a solution for you. Did you had any problems during any previous upgrade? Did the power went out while upgrading or did you disconnect the device?
What you can do is install HDD Usb Monitor, put it in capture mode and try to flash a new rom, then you should be able to see the exact error or reason why it fails from there. If you post the error here it will be useful to diagnose the exact problem and try to find a solution for it.
Hi Pof,
Today they are successful to put within the rom dell imate after six tried to you, for the moment aspect that decoy the rom Italian and then we try and we see if it continues to give stessp the problem. Thanks thousands for the availability.
Tanks
Help me - MDA Vario 2 - M300
I also has same prob with Emblema. My PPC only connect to PC in bootloader mode. I cannot start my PPC after fail upgrade ROM.I tried many times to upgrade but it not success (stop at 0%)
Pls help me to recover or upgrade new ROM
MDA vario II M300
IPL 1.01
SPL - 1.04
Re: Help me - MDA Vario 2 - M300
linhmuc said:
My PPC only connect to PC in bootloader mode. I cannot start my PPC after fail upgrade ROM.
Click to expand...
Click to collapse
Enter the bootloader using mtty, when you see the "USB>" prompt type in these commands (do not copy-paste!):
Code:
USB> set 14 0
USB> task 8
The device should restart and boot the OS. For more info, see this page on the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
I tried 2 command , it successed but hold at windows mobile screen. I want to format ROM and install new ROM, how do i do?
Pls help me.
Thanks.
Have you tried flashing every available ROM for the Hermes? Always get an error?
Can you post here the output of 'info 8' command in bootloader?
Thanks for reply
Here is the result executed command info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1B400
Partition[3], type=0x4, start=0x1E400, total=0x1C400
CE Total Length(with sector info) = 0x3D72000
CE CheckSum Length(without sector info) = 0x3C80000
I also tried other ROM upgrade but it hold at 0%
Everything seems ok to me... sorry for not asking before, but can you post the output of 'checkimage' command?
Which device is it, and which was the last ROM you had on it?
Did you try to unlock it or something before it break?
My PPC is MDA vario II - Herm300
I tried unlock with HTC_Uni_SIM_Unlock_v1 and have an error. From that I cannot start my device.
I execute checkimage command:
IPL CRC checksum = 0xA2BD7A6
SPL CRC checksum = 0x3BF03635
CE CRC checksum = 0x458E70C0
ExtROM CRC checksum = 0x10D845D9
Radio Image CRC checksum =
it stop at "Radio Image CRC checksum = "
I think you have the same problem fluffcat1 describes here:
http://forum.xda-developers.com/viewtopic.php?t=61396
After runing the HTC Universal Unlocker you've screwed the radio of your device, there is no radio rom present and no security area, radio rom upgrade won't success.
There is no known solution to this problem yet, do you have warranty or can get a replacement unit?
@linmhuc:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
to prof:
I run command info 2, but it not execute, it hold, how do i know my PPC CID ?
Hi everybody,
I bought my V1605(French SFR) today and I decide to unlock it with HTC uni Unlock V1 in order to work with my business SIM card.
At the end of the unlocking I've got an error, telling me to try to install again. After resetting my V1605, It stop on Operator logo. I try hard reset but nothing happened, I'm still stuck on operator logo.
Bootloader is in 1.04.
My V1605 is no longer recognized by activsync, I tried with mtty, but impossible to connect on usb.
I tryed to reinstall the original rom, but V1605 can't be find. Same for other rom.
I tryed everything on hermes upgrade Problem page, but nothing works.
When I try to update rom by microsd, it's not working. I have read the wiki page.
Have you got any idea ? You'll be my hero... I'm really in a dead end.
Thanks in advance,
Geof
- disable usb connections on activesync
- put hermes in bootloader mode and connect to computer usb port
- start usb monitor capture ("complete view")
- start update of original rom (retry two times if it fails first)
- when finish, export usb monitor capture to ANSI text format, and attach it here.
Thanks for your help.
It seems that my V1605 is disconnecting when I try to update
oops! the file shows nothing useful. seems disconnected after the first usb setup packet.
When you put it in bootloader mode and connect to usb port, do you see in the bottom part of the screen the string "SERIAL" changes to "USB"? or it stays "SERIAL" ?
Have you tried a different usb port on the same computer? or even a different computer?
Do you get any error when trying to flash from SD card? do you see the "checking...." ?
I tried on 2 computers and on each usb ports...
When I try to update, it stays on usb and never come to serial.
With the Microsd, there is a very very very fast check on card (less than 1/2 seconde), and it stay on bootloader. It seems that it wouldn't want to launch anything from the Microsd.
I retried to use mtty and it connects, but what to do.
I tried with the himalaya rom to get a better USB monitor file. It stuck on white screen on V1605 at 0% on PC.
G3oF said:
With the Microsd, there is a very very very fast check on card (less than 1/2 seconde), and it stay on bootloader.
It seems that it wouldn't want to launch anything from the Microsd.
Click to expand...
Click to collapse
Try it several times... sometimes it is a bit hard to make the bootloader read the image. Make sure you only put the french voda rom NBH file renamed to HERMIMG.nbh on the microSD card, and nothing else.
G3oF said:
I retried to use mtty and it connects, but what to do.
Click to expand...
Click to collapse
checkimage
info 2
info 7
info 8
set 14 0
task 28
...
USB>checkimage
IPL CRC checksum = 0xAB6DDB32
SPL CRC checksum = 0x3BF03635
CE CRC checksum =
USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a
Device Name: H, Bootloader Version : 1.04
Built at: May 26 2006 20:17:35
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19D00
Partition[3], type=0x4, start=0x1CD00, total=0x1DB00
CE Total Length(with sector info) = 0x3A86800
CE CheckSum Length(without sector info) = 0x39A0000
USB>info 2
USB>set 14 0
Write Nand Success
HTCST ÚÈÒHTCEUSB>
USB>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 461
Storage Total block: 475
Total Bad Block in CE: 0
NeedToEraseBlockStart: 474
Storage format success
As you can see some command not working. It seems those commands interrupted the USB link. Have you ever seen this before ????
I continue to try updating by sd, but seems not working.
Thanks for your help
Do you think I have to send it to technical center ?
Probably it's a good desition if you can't fix it by any other way.
I ask for replacement and thy agreed. I'm surprised but very happy. I'm not sure to try to unlocked it right now ;-). Thanks again for your help
Hi
Recieved this fone from a friend
He Flashed the radio on this phone & now phone get stucks on Windows Mobile Logo .
I dont know which Radio he flashed ...
Now phone also not connecting as he says me ..
I dont know all the details .
this is written when HTC shown on startup .
M 05
S 04
B 05
D 1.18
on Boot Loader
HERM200
IPL-1.00
HERM200
SPL-1.04
so any one advice me correct solution how to repair ..
Thanks
Aamir Zia
try this
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
I did Read all
I make Hard Reset successfully
After that on HTC screen , it says NO GSM Then shows White Screen & nothing after that ..
I also did this
Open mtty.exe and select USB port, then connect.
Hit enter twice, you will see the "USB>" prompt.
Type the following commands (do not copy paste!!!)
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
But still not connecting when i flash to Patched Radio
I got error in the end
Error [222] Device not Responding ..
Who can Help me ...
Can you get into bootloader mode?
Yup !!!
I can go into Bootloader mode
HERM200
IPL-1.00
HERM200
SPL-1.04
Now phone comes back to its Original Condition ( Stucked on WINDOWS MOBILE ) ... after leaving it without Battery for 20 minutes ....
But phone still cannot be read ...
Leave it at least 10 minute on windows mobile logo if its manage to pass it.
Next step maybe you can try fired up MTTY & execute below command
1. task 32
2. info 2
What is the output?
While phone is stucked in Windows Mobile Logo i leave it for 15 minutes
but it didnot passed .
&
When i try to enter this command with MTTY
Software Hangs & not responds ....
aamszia said:
While phone is stucked in Windows Mobile Logo i leave it for 15 minutes
but it didnot passed .
&
When i try to enter this command with MTTY
Software Hangs & not responds ....
Click to expand...
Click to collapse
You can try this but I am not sure whether its works or not.
At bootloader screen, try flash full release roms that matching your Hermes CID. or flasing this patch radio roms
http://wiki.xda-developers.com/index.php?pagename=Hermes_SimUnlock
Well i have written above that when i try to Flash the PATCH RADIO ROM
i got this error
Error [222] Device not Responding ..
Phone cannot be detected by software , even computer detects the driver .
& i dont know from where phone is come from ...
POF !!!!
Please help me out here with HTC Tytn
Here are some details via MTTY
Info 2 is not working
info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a
Device Name: H, Bootloader Version : 1.04
Built at: May 26 2006 20:17:35
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x3FB(1019) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19500
Partition[3], type=0x4, start=0x1C500, total=0x1E300
CE Total Length(with sector info) = 0x3982800
CE CheckSum Length(without sector info) = 0x38A0000
USB>
help ,my phone's hang on too..
but display SPL-1.09,
and supercid is lost.
i can't boot x01ht now.
Aamszia:
Look in the following thread at post numbers 120, 236, 237, 238, and 239
http://forum.xda-developers.com/showthread.php?t=286755&page=12
Once you have used these methods to get access to the PDA, put the sspl on a memory card and run it on the pda.
Once you have done that, plug back in to a usb port and run whichever updates you want/need
Mike
Mike
Can You come on Chat Please
Thanks
Hi aamszia,
What do you need to know?
hi
me too, i m stucked on the windows mobile screen ! i'm in bl 1.09.
After trying to fix MapKing problem by flashing different SPL and OS, I have a new problem: shows "no gsm" then hang at windows mobile splash screen.
I have SPL 1.04, HTC_BOOT 1.08, and the wiki says "Flash a ROM with SPL-1.09+KITL enabled OS", but how do I know which OS has KITL enabled?
In addition, all the ROMs are now in RapidShare, and I have problem downloading. Could anyone please help share it in other places?
kuekpeow said:
After trying to fix MapKing problem by flashing different SPL and OS, I have a new problem: shows "no gsm" then hang at windows mobile splash screen.
I have SPL 1.04, HTC_BOOT 1.08, and the wiki says "Flash a ROM with SPL-1.09+KITL enabled OS", but how do I know which OS has KITL enabled?
In addition, all the ROMs are now in RapidShare, and I have problem downloading. Could anyone please help share it in other places?
Click to expand...
Click to collapse
You just need to spend more time reading the wiki...
trashcan said:
You just need to spend more time reading the wiki...
Click to expand...
Click to collapse
What I understand from WIKI is that all ROMs with SPL-1.06, SPL-1.09, or SPL-1.11 have KITL enabled. However, no ROM from Dopod has SPL-1.09 so I will need to flash the ROM from either HTC or Cingular. However, I'm worried that if I still can't get KITL mode, then I can't recover it myself using PB+KITL method. I understand that only SPL-1.04 has the CID bug to be able to flash other operator's ROM, therefore I would probably be stuck with HTC or Cingular splash, which will definitly void my Dopod warranty.
Therfore I will really appreciate if any knowledgable and helpful person could confirm with me that I should proceed to flash shipped SPL-1.09 ROM from other Operator to get KITL enabled OS, in order to use PB+KITL method to recover my bricked Dopod 838 Pro. If this is not a fool proof method, then I would rather sent the unit to Dopod Service Centre for repair...
I also posted in another thread asking for help ("dead hermes? corrupted radio? Post comments here" http://forum.xda-developers.com/showthread.php?t=286755&page=89), but have not got any reply yet...
Original Config: SPL=1.04, HTC_BOOT=1.08, Radio=1.38.00.10, ROM=Jasjamming WM6 v1.2.
What Happened: Flash by CustomRUU v4.2 Forced SSPL: SPL=1.04, HTC_BOOT=1.08, Radio=1.06.00.10, ROM=Dopod 1.23.707.4.
Current Problem: HTC Innovation Splash will show No GSM after few seconds, then hang at WM5 Splash. info 2 does not return SuperCID string anymore, and cannot boot into KITL mode.
Failed Recovery: Flash WM6 LVSW 2007-03-26 result in ERROR [262]:UPDATE ERROR.
USB>task 32
-> Level = FF
USB>info 2
->CID: Wait Interpreter timeout
HTCSUSB>
USB>info 3
->HTCSH
USB>info 7
->HTC Integrated Re-Flash Utility, Common Base Version: 1.50a
Device Name: H, Bootloader Version: 1.04
Built at: May 26 2006 20:17:35
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version= 0x4
Main Board version=0x6
USB>info 8
->Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x0x1CD00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
Already answered in the brick thread.
Cuivienor said:
Already answered in the brick thread.
Click to expand...
Click to collapse
Thanks
A week ago un update went bad (stopped in the middle). My device was (not sure if after so many test it still is) cid unlocked and with hardspl (tried so many roms in one year).
Now my niki100 hangs at smart mobility screen. Tried to flash roms both from RUU (original roms stops with invalid vender id), others (including the ITA original one) stops with 262 error.
Also tried to flash from the SD card but cell hangs in "Loading..." screen.
From MTTY, output of the info commands are:
Code:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 1081 (0x439) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0xAA00
Partition[3], type=0x4, start=0xB740, total=0xFB80
CE Total Length(with sector info) = 0x5BFBA00
CE CheckSum Length(without sector info) = 0x5BA0000
and
Code:
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: Nike, Bootloader Version : 1.16.0000
Built at: Oct 8 2007 18:27:27
Copyright (c) 1998-2007 High Tech Computer Corporation
Board ID=0x4
CPLD ID=0x4
gCurrentPanel=0x4
Searched a lot and read tons of posts but nothing.
Can anyone helps?
Thanks a lot!
Okay, try this:
MTTY -> use command boot -> you are stay in OS -> start SSPL -> Flash your ORIGINAL Rom ...
Goodluck
Tried that... but with the boot command, cell hangs at "smart mobility" screen...
Okay, are you sure you disabled active-sync maybe that causes the trubble.
About flashing, I flash my Niki 6 times a day (learn to cook) so I don't think that is the problem.
I had almost the same issue with an Elfin and I flashed it over and over again and after 9 or 10 times the phone accepted the rom and flashed it complety.
Not sure it was the right procedure to do (or just luck) but it worked.
Or read this http://forum.xda-developers.com/showthread.php?t=390606
Goodluck again