Hello.
I tried to update with the ROM from SD card, but it failed.
My phone doesn't boot after that - it hangs up showing just splashscreen and some info -
ONBL 1.07.0000
SPL 1.10.0lip
GSM 02.71.90
OS 1.8.0.0
Hard reset didn't help.
I tried to flash ROM through RUU (device still goes into bootloader by pressing camera+reset/power), but it said
ERROR [200]: Invlid Update Utility
Please get newer Update Utility
Is there any way to flash my device? =\
btw, sorry for my english, i know that it's quite bad )
You need to first patch your HSPL and then flash a custom ROM.kindly read the ROM Upgrading Guide properly in the GENE forum.you can also find the link in my signature.
karan999 said:
You need to first patch your HSPL and then flash a custom ROM.kindly read the ROM Upgrading Guide properly in the GENE forum.you can also find the link in my signature.
Click to expand...
Click to collapse
If you are talking about that method -
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Click to expand...
Click to collapse
then it didn't work.
Mtty connects to the phone, it even says that bootlader patched, enters the "White screen" but RUU that is situated in the "Orefkov" folder says still the same: ERROR [200]: Invalid Update Tool
And btw, Orefkov method is for new gene only, am i right?
And I have an old one. And it's already have 1.10.0lip SPL, that allows custom ROM flashing.
LordOfFrost said:
And btw, Orefkov method is for new gene only, am i right?
And I have an old one. And it's already have 1.10.0lip SPL, that allows custom ROM flashing.
Click to expand...
Click to collapse
ya..Your SPL is patched and u have old gene
Now u can Flash Any custom rom from here(just No stock roms)
Problem was solved by deliting Active Sync, cleaning registry with CCcleaner and installing Active Sync after that...
I think that there was some driver problem or smthng >_<
Related
I finally found some time to post this, it's been on my desk since February.
Anyhow, today is the day. Oh yes, running this will SIM unlock your device as well
Niki SuperCID and Security Unlocker v0.1
========================================
Brought to you by jockyw2001
(c)2008 jockyw2001
Consider a donation to keep the R&D going
Send your PayPal donation to [email protected]
Rapidshare:
Download-Link #1: http://rapidshare.com/files/95890081/Niki-SuperCID-Security-Unlocker.zip.html
Megaupload:
http://www.megaupload.com/?d=EB83Y4CJ
Note for Vista users
====================
This guide will explain how to change your drivers to the xp:
http://www.modaco.com/content/Windo...UU-on-Vista-It-can-be-done-the-ultimate-guide
You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
1. Make sure you installed HardSPL 1.15 MFG If you did not install 1.15 yet follow instructions here: http://forum.xda-developers.com/showthread.php?t=355730
To verify if HardSPL is correctly installed: power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-color screen (Red, Green, Blue). You should see "SPL-1.15.Hard" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.58.16.27"). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. You can download radio roms from XDA devs here:
http://forum.xda-developers.com/showthread.php?t=369502
EDIT: if your current radio version is 1.65.28.25 or higher you should first downgrade to a lower ROM version like RUU_Nike_Radio_1.58.21.23_25.65.30.04S_Modded.
3. Connect PC and Niki with a USB cable and keep it connected until the last step.
4. Power on the Niki and let it boot into Windows Mobile. On the PC make sure the activesync icon is green.
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run NikiCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished. IMPORTANT: Make sure that the flash correctly finished. The device will restart automatically once the flashing is completed.
6a. Power off and power on in tri-color bootloader mode.
6b. Unplug and replug usb cable and wait 10 seconds
7a. right-click activeync icon and uncheck "Allow USB connections" from Connection Settings
7b. On your PC go into the "step2" directory and run "Niki-supercid.exe".
You should see this:
--------------------
=== Niki SuperCID and Security Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email protected]
[] Done, your device should now be superCID and Security Unlocked
[] Your device is unlocked and you can change anything anytime
[] Don't forget to flash your original radio
Press Enter to exit
-------------------
If you see this:
----------------
=== Niki SuperCID and Security Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email protected]
Your CID = HTC__001
[] Failed! Please soft reset and try again
[] To soft reset press and hold camera button and then press reset with stylus
Press Enter to exit
-------------------
then do a soft reset (press and hold the camera button first and then shortly press the reset button with the stylus) and try again.
8. Download the original radio from here:
http://forum.xda-developers.com/showthread.php?t=349375
to the "step3" directory on your PC and flash it with NikiCustomRUU.exe
9. right-click activeync icon and check "Allow USB connections" from Connection Settings
That's all folks
Enjoy and ... donate to keep R&D going! Thx!
Send your PayPal donation to [email protected]
JockyW
Edit: Niki Security Relocker
Some users with a security unlocked device would like to relock it again e.g. for warranty purposes. Unzip niki-relock.exe from the attached niki-relock.zip into the "step2" directory of the security unlocker (in the same directory there should be niki-supercid.exe). Carry out the same steps as for the security unlocker but in step 7b run niki-relock.exe
Have fun!
Credits
=======
* des, pof and olipro for SSPL and HardSPL
* arc and all the other great minds at XDA devs
* viperbjk, adfree and all other QC hackers at Modopo
(c)2008 jockyw2001
[email protected]
Feb 29th 2008
Once again, thanks for all your work!
You are the king!
Thanks allot for the hard work and sharing the tool! You rule
stickied well done
it took a long time but it was worth waiting !
jocky - thanks for your time spent on this, thanks for sharing this tool with the niki community and please stay with us and help us from time to time ;-)
again thanks king jocky
Awesome. Great work.
hi
does this also unlock cid? i mmean the basic one
the_fish said:
hi
does this also unlock cid? i mmean the basic one
Click to expand...
Click to collapse
It unlocks everything there is to be unlocked. lol
Nice works brother
Well done(but little bit late for me as i already unlocked my Nike)and thanks for your hard work mate.Any news on Wings yet?
Cheers
deleted ;-)
Vista x64? Nope.
sackbauer said:
deleted ;-)
Click to expand...
Click to collapse
What do you mean buy that?Links working 101% so,check again.
@[email protected] said:
What do you mean buy that?Links working 101% so,check again.
Click to expand...
Click to collapse
He means "post deleted". That is because he posted in the wrong place.
_______________________________________________
Please post some feedback about this tool...
Okk..i flash the patched radio and boot phone back on holding dowen camera to boot into tri-color screen 1.15.hard
I then load Niki-supercid.exe from step 2 from which brings up CMD with below then just a flashing cursor
=== Niki SuperCID and Security Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email protected]
_
How long should this process take and if it should be immeditate where am i going wrong?
Regarding previous post my phone is also locked onto correct network now aswell so phone is pretty unusable with a sim card in
HELPPP PLease
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.58.16.27"). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. You can download radio roms from XDA devs here:
http://forum.xda-developers.com/showthread.php?t=369502
Have you done that mate?
Yes just flashed back to correct radio and i can now use sim card again. but still phone did not successfully unlock
Then try again mate:
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run NikiCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished. IMPORTANT: Make sure that the flash correctly finished. The device will restart automatically once the flashing is completed.
6. Power off and power on in tri-color bootloader mode.
7a. right-click activeync icon and uncheck "Allow USB connections" from Connection Settings
7b. On your PC go into the "step2" directory and run "Niki-supercid.exe". If all went well you will see the unlockcode on your monitor and your Niki is being restarted automatically.
7c. right-click activeync icon and check "Allow USB connections" from Connection Settings
Tried about 5 times lol
Get as far as this:
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run NikiCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished. IMPORTANT: Make sure that the flash correctly finished. The device will restart automatically once the flashing is completed.
6. Power off and power on in tri-color bootloader mode.
7a. right-click activeync icon and uncheck "Allow USB connections" from Connection Settings
7b. On your PC go into the "step2" directory and run "Niki-supercid.exe". If all went well you will see the unlockcode on your monitor and your Niki is being restarted automatically.
-- This opens a cmd box but just hangs and screen stays on tri-color boot screen.
Gene 100 stuck on bootloader mode
it is left with a tricolor screen with
ONBL 1.17.0000
SPL 1.10.olip
if i update any rom it says invalid update tool error 300
can any one provide a working solution
willing to pay
There is only one fix.... that is hard reset the device without even powering it on .....and please search the forum completely... i have also posted a video on YOUTUBE about this ...!
let me know how it goes.....
http://forum.xda-developers.com/showthread.php?t=375064
???????????????????????????
a1cellsolution said:
Gene 100 stuck on bootloader mode
it is left with a tricolor screen with
ONBL 1.17.0000
SPL 1.10.olip
if i update any rom it says invalid update tool error 300
can any one provide a working solution
willing to pay
Click to expand...
Click to collapse
Ahhh!!
i was having the same problem
Do the following steps !
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Click to expand...
Click to collapse
Do this step Carefully
Do THe all step again and listen carefully
After completing 5st step
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
Click to expand...
Click to collapse
type the next command in pc wait do not press enter
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Click to expand...
Click to collapse
<----------- This one
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
Hold camera button and then press enter
Click to expand...
Click to collapse
after that complete your further steps !!
hope it will work !! (Good Luck)
Sry for my bad english
([email protected])
or if you are on vista or seven ,then
You need to take these steps :
1. Go to desktop, right click Computer, and select Manage. Go to Device Manager. Now under the section Mobile Devices, Double Click : Smartphone USB Sync.
2. On the Drivers tab, click "Update Driver..." button. On next screen click : "Browse my computer for driver software".
3. Click : "Let me pick from a list of device drivers on my computers". Click "Have Disk.." on next screen. Click "Browse..." and go to the folder extracted in step 1. There, go to USBDriverforActiveSyncVista folder. Here select the file "wceusbsh.inf" and click OK.
4. Click Next and finish the wizard.
Buddy, this is one year old thread. The guy who has posted it might have changed his phone, thrown it in the dustbin, or probably has solved his problem long ago. Why are u bumping it now? Try to check the date of the last post before posting man
bump
its bcuz the man is willing to pay
i have htc gene100 dead (because of wrong upgrade and wrong spl.) when i want to upgrade with each version ,i recive this error : "get newer update utility " or " Invalid update tool error" . i try mtty (unbrick with mtty) and when the screen becom white and i want to upgrade that story repeat. Please help me . please ....
(I read other posts but i cant find any solution)
Arian57 said:
i have htc gene100 dead (because of wrong upgrade and wrong spl.) when i want to upgrade with each version ,i recive this error : "get newer update utility " or " Invalid update tool error" . i try mtty (unbrick with mtty) and when the screen becom white and i want to upgrade that story repeat. Please help me . please ....
(I read other posts but i cant find any solution)
Click to expand...
Click to collapse
There is a simple repair tutorial
1. Turn off your cell phone into the tri-color screen.
2. In the PC, open the Task Manager to end the "wcescomm.exe" process.
3. The phone line to connect USB and PC, mobile phone screen in the lower left-hand corner the "USB";
the first time, there will be connected to install the driver.
4. running mtty1_42.exe, the interface of choice in the "USB".
5. Mtty1_42.exe input of the current window: can not paste
(1): Enter a Return
(2): set 32 1
(3): Enter a Return
6. To wait for information to complete the rolling
7. To continue in the window, type:
(1): ls boot.bin first
(2): hold down the camera button
(3): Enter a Return
8. Waiting for white screen , After a few seconds release the camera button.
9. Exit Mtty software
sm7s said:
There is a simple repair tutorial
1. Turn off your cell phone into the tri-color screen.
2. In the PC, open the Task Manager to end the "wcescomm.exe" process.
3. The phone line to connect USB and PC, mobile phone screen in the lower left-hand corner the "USB";
the first time, there will be connected to install the driver.
4. running mtty1_42.exe, the interface of choice in the "USB".
5. Mtty1_42.exe input of the current window: can not paste
(1): Enter a Return
(2): set 32 1
(3): Enter a Return
6. To wait for information to complete the rolling
7. To continue in the window, type:
(1): ls boot.bin first
(2): hold down the camera button
(3): Enter a Return
8. Waiting for white screen , After a few seconds release the camera button.
9. Exit Mtty software
Click to expand...
Click to collapse
i do that comoletely and didnt recieve any erroe during mtty prosses but still my phone in dead and i cant upgarde that.
salam arian jan.
first Copy boot.bin from (gene_unbricker) folder to c:\boot.bin and :
1. Unpack all in some folder.
2. Press and HOLD "Camera" button and turn on device.
3. If you see 3-colored screen, release "Camera" button, else try again.
4. Kill ActiveSync on computer - Press Ctrl+Shift+Esc, found "wcescomm.exe"
process and terminate it.
5. Connect USB-cable to device.
(In the left bottom corner of the screen to appear the text "USB")
6. Run mtty1_42.exe programm, and press button "USB".
7. In the opened window type the text:
set 32 1
Press Enter. (You must type this text by hand, not copy/paste)
8. After you will see answer from device in window.
9. Type in window that text:
ls boot.bin
Press and HOLD "Camera" button, and press Enter.
10. After a while the device screen becomes white.
Wait 2-3 second, and release "Camera" button.
11. Close mtty programm.
12.YOU MUST see have NEW GENE(HT8XXX) OR OLD GENE(HT7XXX)
next copy ruu_signed.nbh from (for new Gene (SN - HT8x)) or (for old Gene (SN - HT7x)) in gene_unbricker folder and Run RomUpdateUtility.exe programm and follow her instruction.
download gene_unbricker.zip
ZELALAT said:
salam arian jan.
first Copy boot.bin from (gene_unbricker) folder to c:\boot.bin and :
1. Unpack all in some folder.
2. Press and HOLD "Camera" button and turn on device.
3. If you see 3-colored screen, release "Camera" button, else try again.
4. Kill ActiveSync on computer - Press Ctrl+Shift+Esc, found "wcescomm.exe"
process and terminate it.
5. Connect USB-cable to device.
(In the left bottom corner of the screen to appear the text "USB")
6. Run mtty1_42.exe programm, and press button "USB".
7. In the opened window type the text:
set 32 1
Press Enter. (You must type this text by hand, not copy/paste)
8. After you will see answer from device in window.
9. Type in window that text:
ls boot.bin
Press and HOLD "Camera" button, and press Enter.
10. After a while the device screen becomes white.
Wait 2-3 second, and release "Camera" button.
11. Close mtty programm.
12.YOU MUST see have NEW GENE(HT8XXX) OR OLD GENE(HT7XXX)
next copy ruu_signed.nbh from (for new Gene (SN - HT8x)) or (for old Gene (SN - HT7x)) in gene_unbricker folder and Run RomUpdateUtility.exe programm and follow her instruction.
download gene_unbricker.zip
Click to expand...
Click to collapse
Thanks Friends
I did that complety and i didnt recieve any error during mtty prosses but when i want upgrade i reciev those error again.
my phone is dead and i cant check it for new or old but i guess it 's old and i get this file for upgrade. is it ok?
http://rapidshare.com/files/222835965/21501_WWE_OLD.rar
please ...
hi ARIAN
you must see serial number phone if SN:HT8XXX you have NEW GENE.if SN:HT7XXX YOU have OLD GENE and use best ruu_signed.nbh then use mtty software for unbrick phone.
then use mtty software and see white screen you must again install Microsoft ActiveSync and use ROMUpdateUtility.exe .
ZELALAT said:
hi ARIAN
you must see serial number phone if SN:HT8XXX you have NEW GENE.if SN:HT7XXX YOU have OLD GENE and use best ruu_signed.nbh then use mtty software for unbrick phone.
then use mtty software and see white screen you must again install Microsoft ActiveSync and use ROMUpdateUtility.exe .
Click to expand...
Click to collapse
thank you very much ............ I post result
ZELALAT said:
hi ARIAN
you must see serial number phone if SN:HT8XXX you have NEW GENE.if SN:HT7XXX YOU have OLD GENE and use best ruu_signed.nbh then use mtty software for unbrick phone.
then use mtty software and see white screen you must again install Microsoft ActiveSync and use ROMUpdateUtility.exe .
Click to expand...
Click to collapse
my phone is old. I install Active sync again (it didnt connect to activesync) and I did whatever you told but ... no result. the same as past
YOU MUST INSTALL Microsoft ActiveSync V4.5.Microsoft ActiveSync V4.2 NOT UPDATE ROM
i hav got the same problem but i am not able to solve it i use win vista n it does not have any active sync..... wot should i do in that case..
read krazy's sticky
emoboy804 said:
i hav got the same problem but i am not able to solve it i use win vista n it does not have any active sync..... wot should i do in that case..
Click to expand...
Click to collapse
Hi!
Please read krazy's sticky about upgrading...
he has explained it very beautifully how to upgrade using vista....
there are certain extra drivers to be downloaded and used in vista....
give it a try and good luck...happy flashing
ZELALAT said:
YOU MUST INSTALL Microsoft ActiveSync V4.5.Microsoft ActiveSync V4.2 NOT UPDATE ROM
Click to expand...
Click to collapse
I have Active sync 4.5 could you please check your private massage?
which one is mine gene old or new????
my gene s/n is sz711fw00644 A
how i know my gene is old or new....???????????
See here. btw always read the Stickies first. You can find this information there.
thanks for nice reply but sir.. my gene is hung in tri-color...
Did you already unlocked your Phone (Hard-SPL)? Put a detailed information here. So others can help better.
Windows Mobile 6.1
- then device try to configure itself, showing something like disclaimer screen
of Michyprima (I press Continue)
- It asked to choose font: Tahoma or Segoe UI (Vista)?
i just leave it that way (Tahoma) & press Done
- a window appear with text: the changes will be visible only at next startup.
i clicked ok (as this is the only way to continue)
- It says customization will be in 3 secs. It resets by itself.
- the boot process is start all over again from the beginning as continuous looping
after long search of what caused it, i found that i have flashed wrong version of Michyprima's ROM SPL, other words: i used the rom for SPL v3.5 instead of SPL v1.2 version.
Now I do not know how to correct the unit.
Yes I searched and found the same problem but no solution simple enough for me to understand.
Can anyone please help with this, thank you.
i had the same problem before, looping after flashing. but i forgot how i fixed it. tootallk2000 was helping me through the procedure then. maybe he can remember how we fixed it.
Try this step:
1) boot into bootloader mode (push camera and volume all the way down and press reset)
2) Flash any SPL 1.2 rom or stock rom using bootloader mode (untick allow USB connection if activesync unable to detect)
3) done , make sure you only flash SPL 1.2 rom after the unit has been revived
ps : you may also try using SDcard (not SDHC) flashing if unable to connect using activesync. Just rename RUU_signed.nbh to atheimg.nbh and copy into sd card (sdcard must be formatted as fat32). Put sdcard into device and boot into bootloader mode. It will automatically start the process.
pps : if you see there's no ATHE100 on the bootloader screen, then your modelid is corrupted, need to fix it first before you can do any reflash ... plz read post #33 here : http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
same prob?
http://forum.xda-developers.com/showthread.php?t=470524&highlight=wifi
Hi,
Customer Bring Me Bricked Gene(Dead Condition)
Its Only Go To Boot Loader Mode and also detactable
(USB Icon Show When Enter Cable)
Here is the Details.
ONBL 1.07.0000
SPL 1.10.Olip
Serial Number Start with 8XX
When I Would Like To Update Rom With Rom Update Utiliy This Error Appear.
p3400 error 300 invalid update tool
How To Solve This Problem ?
Is My Genie is Old?
Rgds
Bluffmaster
bluffmaster said:
Hi,
Customer Bring Me Bricked Gene(Dead Condition)
Its Only Go To Boot Loader Mode and also detactable
(USB Icon Show When Enter Cable)
Here is the Details.
ONBL 1.07.0000
SPL 1.10.Olip
Serial Number Start with 8XX
When I Would Like To Update Rom With Rom Update Utiliy This Error Appear.
p3400 error 300 invalid update tool
How To Solve This Problem ?
Is My Genie is Old?
Rgds
Bluffmaster
Click to expand...
Click to collapse
Go through the Rom upgrading guide.Read thoroughly and follow every step carefully.there is a difference between Old Gene and New Gene.You will learn as you follow the guide as to which one is yours.Also to avoid invalid update tool errors,make sure your device is properly synced to yur computer.In your cas as the device is fully dead.Perform a Hard Reset.Even if that doesnt work,you have to use JTAG method to get back your Gene.
So follow the Guide and you'll do good.Revert back when your problem is solved.And do not Create New Threads unnecessarily.Post your doubts in the respective threads.
karan999 said:
Go through the Rom upgrading guide.Read thoroughly and follow every step carefully.there is a difference between Old Gene and New Gene.You will learn as you follow the guide as to which one is yours.Also to avoid invalid update tool errors,make sure your device is properly synced to yur computer.In your cas as the device is fully dead.Perform a Hard Reset.Even if that doesnt work,you have to use JTAG method to get back your Gene.
So follow the Guide and you'll do good.Revert back when your problem is solved.And do not Create New Threads unnecessarily.Post your doubts in the respective threads.
Click to expand...
Click to collapse
Hi
I follow the guide and Upgrade my SPL Olipro to Orefkov's.
PHP:
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 5 of Guide is Goes Well....
But Guide Show in Step 6 phone boot Once
PHP:
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
But Mine is Still Dead When i Press Power Button only redlight blink.
also it can go to bootloader when i press power + camera key.
i have sucessfully update my rom but now phone still dead
rgds
bluffmaster
bluffmaster said:
Hi
I follow the guide and Upgrade my SPL Olipro to Orefkov's.
PHP:
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 5 of Guide is Goes Well....
But Guide Show in Step 6 phone boot Once
PHP:
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
But Mine is Still Dead When i Press Power Button only redlight blink.
also it can go to bootloader when i press power + camera key.
i have sucessfully update my rom but now phone still dead
rgds
bluffmaster
Click to expand...
Click to collapse
Hi Friend i have the same problem
I successfully go to the (3. Connect the USB cable. The text USB will appear on the bottom of the screen.) after that when touch the usb text on my mobile it not responding & the Mtty1_42.exe programe the window will open but i cannot write any thing. please help me .
Make sure that you have removed SIM card and Storage card and try to connect it again.Then run mtty1_42.exe and select USB in the port then press OK.Hope this will help you.
mr.harsh said:
Make sure that you have removed SIM card and Storage card and try to connect it again.Then run mtty1_42.exe and select USB in the port then press OK.Hope this will help you.
Click to expand...
Click to collapse
I already remove my sim & storage card but now i can not switch on my phone / When i Press Power Button only redlight blink. also it can go to bootloader when i press power + camera key.
gcpganesh said:
Hi Friend i have the same problem
I successfully go to the (3. Connect the USB cable. The text USB will appear on the bottom of the screen.) after that when touch the usb text on my mobile it not responding & the Mtty1_42.exe programe the window will open but i cannot write any thing. please help me .
Click to expand...
Click to collapse
good morming
On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
it don´t apear any window after run mttyy1_42. Open a program bu i don´t see any button USB!!!
Cam you help me??
Thanks
HLCMAD said:
good morming
On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
it don´t apear any window after run mttyy1_42. Open a program bu i don´t see any button USB!!!
Cam you help me??
Thanks
Click to expand...
Click to collapse
Thank u friend
when i chose USB button of mobile it is not responding & I can not write any thing in mttyy1_42 programe.
to be able to do the command in the MTTY programe, for the first you should disable activesync -> connection settings -> uncheck "allow USB connections"
Hakim Rahman said:
to be able to do the command in the MTTY programe, for the first you should disable activesync -> connection settings -> uncheck "allow USB connections"
Click to expand...
Click to collapse
Thank you friend i already done it, when conect the phone to computer through USB ,In a corner position of the phone USB is written, but when i open the MTTY program it open & shows the Port option to chose , but it is not showing the USB option in that option.
gcpganesh said:
Thank you friend i already done it, when conect the phone to computer through USB ,In a corner position of the phone USB is written, but when i open the MTTY program it open & shows the Port option to chose , but it is not showing the USB option in that option.
Click to expand...
Click to collapse
If it does not exist, You can add it by typing USB on port column option
Hakim Rahman said:
If it does not exist, You can add it by typing USB on port column option
Click to expand...
Click to collapse
Thank U,
I add it but i got this " \\.\WCEUSBSH001 port can not open" Error Message.
(If Any thing i have to do after connecting USB Cable to phone to PC)
gcpganesh said:
Thank U,
I add it but i got this " \\.\WCEUSBSH001 port can not open" Error Message.
(If Any thing i have to do after connecting USB Cable to phone to PC)
Click to expand...
Click to collapse
You've kill processes wcescomm.exe on Task Manager ??
Hakim Rahman said:
You've kill processes wcescomm.exe on Task Manager ??
Click to expand...
Click to collapse
Thank u Friend
Now how can i update 6 professional to 6.5
gcpganesh said:
Thank u Friend
Now how can i update 6 professional to 6.5
Click to expand...
Click to collapse
for upgrade to WM 6.5, you can follow existing Guide by krazy_about_technology at http://forum.xda-developers.com/showthread.php?t=472169