Can't uprom ship prophet after flashing SPL ship - G4

I try to dump rom ship by HyperCore_V1.01.exe
so there are two spl 91000000-SPL_1.nb & 91000000-SPL_2.nb
Because of the same size (768k) ,so i only use 91000000-SPL_1.nb to convert to nbf by using nb2nbf.exe
After flashing SPL .Boot loader shows that IPL 2.20.0001 and SPL 2.20
but i made a mistake.Hex editor XVI32 show that 91000000-SPL_1.nb & 91000000-SPL_2.nb is different
now i can't use rom ship or NVID ROM to recover
Hepl me solve my problem
thanks

boot loader

help me !!!
thanks

Xsite_01 said:
As your phone can turn on and you have bootloader, you can recover it. so go to device manager on your PC as see if the driver is installed and download NVID rom and flash it. And add some more explaination of your problem.
Click to expand...
Click to collapse
i have tried NVID rom and flash it .but stop at 80%
can you give me some advice ?
thanks !!!

Xsite_01 said:
try Hard SPL, and post results.
Click to expand...
Click to collapse
oh ,my phone cant load OS .it just show boot-loader.
perhap, my DOC die!!!

Xsite_01 said:
You dont need to load os. you have what you need thats bootloader. Means that your phone is not dead. Go to This you have all info and files, see if your phone is g3 or g4 and flash Hard SPL.
Click to expand...
Click to collapse
thank you very much
i will try immediately and report later

i try to use Upgrade_HardSPL_G4 but unsuccess
i chose yes but it ask again
--> no
-->
then RUU run
and
in my opinion ,when load OS ok.active synce OK
then HARD SPL
when just boot loader ,you cant hard spl
normally my spl 2.20.0001
but now spl 2.20 --> spl fail

Related

Is it possible to downgrade SPL in a G4?

i upgrade the ROM using this :
http://forum.xda-developers.com/showthread.php?t=283965
but I would like to downgrade it again to send for repair ...
i cannot flash it back to the original IMATE JAMIN rom , always stop at 95%.
Please help.
Just wait, suddently it continue.
Regards
"Just wait, suddently it continue."
No, it doesnt. Error msg comes out and forces you to it.
SPL can not be easily downgrade by flashing ROM in a G4.
Same problem
I have same similar problem.
I created new topic. I guess my topic more explanatory.
Lets go on here -> http://forum.xda-developers.com/showthread.php?t=331474
thanks..
NOW it is possible to downgrade SPL. Just flash HardSPL, after that you can DOWNGRADE SPL to any SPL you want!!!
nForce said:
NOW it is possible to downgrade SPL. Just flash HardSPL, after that you can DOWNGRADE SPL to any SPL you want!!!
Click to expand...
Click to collapse
When you first flashed HardSPL, which verson of the SPL was shown after reboot? That, what you had before, or the new one, of the HardSPL? I am asking, because I managed to keep the original O2 2.15 SPL and I really dont want to channge it (for repair reasons
After flashing the patched HardSPL I see 2.G4.4PDA (I have a G4 XDA Neo)! But the good news are that you now can flash all SPL versions you want, like the original 2.15 when it's inside of your ROM image and you can see it after rebooting!
How to use Hard SPL if a can't pass bootloader?
I tryed hard SPL, but after upgrading it back to 2.20.001., and I can't pass even to "Windows mobile" screen and it is frozen this position.
Any suggestions?
Thanks

safe WM5 ROM for my G4

i would like to downgrade to WM5 official ROM,
i got one from this link http://www.tm-phonedownloads.com/dow...mda_vario.html
but this is not safe for G4 device coz it bricked someonesfone in G4 forum..
where can i have a safe base ROM for my G4 device, the one that wont harm my IPL/SPL so that i could downgrade back to WM5...
thanks.
rizortiz
rizortiz said:
i would like to downgrade to WM5 official ROM,
i got one from this link http://www.tm-phonedownloads.com/dow...mda_vario.html
but this is not safe for G4 device coz it bricked someonesfone in G4 forum..
where can i have a safe base ROM for my G4 device, the one that wont harm my IPL/SPL so that i could downgrade back to WM5...
thanks.
rizortiz
Click to expand...
Click to collapse
If you had read carefully, you would have known that that rom didn't brick his device.
He HAD that ROM but then decided to flash an older ROM which didn't contain the G4 IPL/SPL, thus bricking his device by flashing G3 IPL/SPL.
another question..
the-equinoxe said:
If you had read carefully, you would have known that that rom didn't brick his device.
He HAD that ROM but then decided to flash an older ROM which didn't contain the G4 IPL/SPL, thus bricking his device by flashing G3 IPL/SPL.
Click to expand...
Click to collapse
but this was what he said before..
[QUOTE ]
Originally Posted by Krzycho_666
I had RUU_Prodigy_2210206_22102109_021911_TMO_UK_WWE_Shi p on board (the newest ROM from T-Mobile.co.uk).
I have got black sceen, power, bootloader, and hard reset doesn't works.... When I plug USB cable to my PC LEDs wont light... [/QUOTE]
you mean that official ROM from is safe to be flashed with my wizard?
is that official ROM wont change my IPL/SPL? does it only contain OS?
thanks.
rizortiz
Officiall ROM of your provider is safe to flash in normal way...
Fro example I have CID locked G4 MDA Vario from T-Mobile CZ so I can flash T-Mobile CZ ROM without any problems in a normal way (without SoftSPL, shelltools etc. - just normally).
In fact I do this before every flashing of a custom WM6 ROM
Mirek
@rizortiz:
he excactly said:
I had RUU_Prodigy_2210206_22102109_021911_TMO_UK_WWE_Shi p on board (the newest ROM from T-Mobile.co.uk).
I have got black sceen, power, bootloader, and hard reset doesn't works.... When I plug USB cable to my PC LEDs wont light...
I tried to flash RUU_Prodigy_1060204_105_11210_TMO_UK_Ship to unlock CID.... I used SoftSPL-V0.1 to make it. But there is one thing more... Whe I tried to use SoftSPL-V0.1 RUU didn't want to connect my phone... SO I've disconnected phone and restarted PC (screen was still white). Then RUU "saw" my phne and my phone seamed to be upgraded.... Instalation was complete and there was a bootloader on the screen with information about IPL/SPL - but IPL was different then SPL. IPL was 1.06 and SPL was 2.21.olip (that was ok... - am I right?? )... I tried to shot it down.... and.... my device don't want to startup!!!! IS there any rescue for my machine???
Click to expand...
Click to collapse
ahh, why am I even defending what I said..
BTW,
Why try flashing a stock ROM with sSPL?
you can flash an original stock rom to your cid-locked device without sSPL.
Sad but true, if you flash a G4 unsafe rom thats it, your device is bricked. Equinoxe made a perfect softspl in my opinion and if other users dont take the time to read what he says and bricks their device its on their head, not his.
okay..
so i thought it was the first ROM that he installed that bricked his device..
because hardreset, soft reset and bootloader not working anymore..
well anyway, do you mean to say it would be safe to flash
that ROM (the latest from t-mobile) to my t-mobile?
does it not contain IPL/SPL?
how will i check it so that it wont brick my device? thanks.
rizortiz
rizortiz said:
okay..
so i thought it was the first ROM that he installed that bricked his device..
because hardreset, soft reset and bootloader not working anymore..
well anyway, do you mean to say it would be safe to flash
that ROM (the latest from t-mobile) to my t-mobile?
does it not contain IPL/SPL?
how will i check it so that it wont brick my device? thanks.
rizortiz
Click to expand...
Click to collapse
you can use Typho5, http://www.savefile.com/files/1066484
Please follow these steps to the dot.
1. Extract typo 5 to root. "c:\typho5\
2. Copy the nk.nbf file of your os to c:\typho5\
3. Go to command prompt and type "cd\" "cd typho5" "typho5 -x nk.nbf
4. You will see the info in the command prompt regarding the os you want to flash. Please delete all files afterwards except typho5.exe and nk.nbf.
Please tell us your ipl/spl first. Softspl is G4 only.
yeah...
saa044 said:
Please follow these steps to the dot.
1. Extract typo 5 to root. "c:\typho5\
2. Copy the nk.nbf file of your os to c:\typho5\
3. Go to command prompt and type "cd\" "cd typho5" "typho5 -x nk.nbf
4. You will see the info in the command prompt regarding the os you want to flash. Please delete all files afterwards except typho5.exe and nk.nbf.
helloo..
i already did what u said..
i had these files..
80040000-OS.nb
92000000-Splash.nb
96000000-GSM.nb ----------> does it mean, it will change my radio version?
9b000000-Extension.nb
9d000000-HTC.nb
where is that IPL/SPL? how will i knw it wont change my IPL/SPL?
i already used sSPL with TNT 5.0, thanks to equinoxe tool for that..
i already have WM6 on my fone..
i just want to downgrade to WM5, i am afraid if these WM5 roms including wizard love rom contains new IPL/SPL that could brick my fone..
currently, i have IPL/SPL of 2.26.0001 so its a G4.
thanks.
rizortiz
Click to expand...
Click to collapse
Click to expand...
Click to collapse
rizortiz said:
saa044 said:
Please follow these steps to the dot.
1. Extract typo 5 to root. "c:\typho5\
2. Copy the nk.nbf file of your os to c:\typho5\
3. Go to command prompt and type "cd\" "cd typho5" "typho5 -x nk.nbf
4. You will see the info in the command prompt regarding the os you want to flash. Please delete all files afterwards except typho5.exe and nk.nbf.
helloo..
i already did what u said..
i had these files..
80040000-OS.nb
92000000-Splash.nb
96000000-GSM.nb ----------> does it mean, it will change my radio version?
9b000000-Extension.nb
9d000000-HTC.nb
where is that IPL/SPL? how will i knw it wont change my IPL/SPL?
i already used sSPL with TNT 5.0, thanks to equinoxe tool for that..
i already have WM6 on my fone..
i just want to downgrade to WM5, i am afraid if these WM5 roms including wizard love rom contains new IPL/SPL that could brick my fone..
currently, i have IPL/SPL of 2.26.0001 so its a G4.
thanks.
rizortiz
Click to expand...
Click to collapse
Dude its hard to keep track when you are working "me" and discussing the same thing on this thred also Read my reply on the other thred. http://forum.xda-developers.com/showthread.php?p=1522298#post1522298 And also I would recommend downgrading to your official wm5 rom, if you know it is safe and have done it before.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
pls help me-- kjam
Hi ,I have a kjam which is dead now. I have bootloader in 3color and also detect usb but I couldent downgrade and uograde . pls direct me and interduce some linke which shows the suitable rom and the software which I can flashing my rom or doing best like hspl or sspl without activesynce connectivity.
kjam wizard g4 series ending with 0001
tnx olot
I am waiting for your early replay
kourosh

Hard_spl is dead,now it is three color screen !!

Before flash ROMS, My phone is T-Mobile MDA, IPL 2.21.0001 and SPL 2.21.olip.
It cannot boot because I flash it use ROM with IPL and spl. now IPL 2.21.0001 SPL 2.21.
now power is three color screen !
Help me !!
sanp007 said:
Before flash ROMS, My phone is T-Mobile MDA, IPL 2.21.0001 and SPL 2.21.olip.
It cannot boot because I flash it use ROM with IPL and spl. now IPL 2.21.0001 SPL 2.21.
now power is three color screen !
Help me !!
Click to expand...
Click to collapse
Sorry dude, it's a brick if you have G4 IPL mixed with a G3 SPL..
Man, you really need to read the sticky's next time!
You've propably flashed a rom that includes IPL/SPL on a G4 Device.
SPL 2.20
Hi, I have the same problem...
I make a download from another site like 2.20.0001 but SPL was 2.20.0000...
I tryed any solutions but get no results.
Help me. How can I flash my S200. I try to use JAFWM but ask me for Pkey.
I don't know what to do.....
the-equinoxe said:
Sorry dude, it's a brick if you have G4 IPL mixed with a G3 SPL..
Click to expand...
Click to collapse
I get the same problem,how can fix item?
this fix is quite easy.
Just download a original rom for your device. Search the forum.
you can also try KhanX Extended ROM
small 10mb so it does not take long to flash.
http://forum.xda-developers.com/showthread.php?t=365376
hope this helps.
It is definite not a ROM-only problem.
As xecutionkrk said, try to flash with your original stock ROM, it may be possible to restore the IPL and SPL version.
If that doesn't to the job, then it is another type of brick.
starkwong said:
It is definite not a ROM-only problem.
As xecutionkrk said, try to flash with your original stock ROM, it may be possible to restore the IPL and SPL version.
If that doesn't to the job, then it is another type of brick.
Click to expand...
Click to collapse
It's impossible to flash a rom on a device which has mixed (G3/G4) IPL/SPL.
Due to block-size differences between G4 DoC and G3 DoC (Disk on Chip) the device is unable to write.
OK, learnt from that.
However why is it possible to write G3 SPL to G4...
Did you read this yet?
http://forum.xda-developers.com/showthread.php?p=1177659#poststop
Check out the Wizard Love Rom.... Don't panic yet.
Good luck.
PeterClayton said:
Did you read this yet?
http://forum.xda-developers.com/showthread.php?p=1177659#poststop
Check out the Wizard Love Rom.... Don't panic yet.
Good luck.
Click to expand...
Click to collapse
Thats for if you are stuck on bootloaders with the same G4 IPL/SPL to recover back to normal,but not to not to recover from a 'Bricked' phone due to a mixed G3/G4 ipl/spl.
Cheers!
starkwong said:
OK, learnt from that.
However why is it possible to write G3 SPL to G4...
Click to expand...
Click to collapse
Because the already loaded SPL is the correct one, and it will write the incorrect G3 SPL with the right blocksize to the DoC.
After reboot the new bootloaders are being utilized for the first time, and then the troubles begin, the "new" G3 SPL will be read correctly, but is unable to read or write to the DoC.
JTAG* would be the only solution to solve this problem.
*JTAG for HTC wizard is NOT available (-no known test points, no real datasheets for omap 850 in order to find these test points, no real omap850 datasheets available for timings and commands in order to succesfully communicate).

Can anyone help my M600?? Please!

Hi, I have been running Gollum's Prophet Touch VII on my M600 for ages now and fancied a change, I decided to dl varanusvincent's 'my diamind edition 2' and ran the g4 rom update that came with it, my m600 now is sat in the 3 colour bootloader screen with IPL 2.10.0001 and SPL 2.20.0001 and I cant get it to do anything, hard reset just puts it back to the bootloader screen, can ANYONE help me please or have I wrecked it by trying to install a new rom?
thanks
Mike
I've reset it again and it is now stuck on the 'qtek keep the world as one' screen with ipl and spl in the top left corners, the uodate programmes all say that is disconnected if i try and use them any ideas??
have you read how to upgrade it????
You haven't HARDSPL.
READ HERE to recovery your Prophet
I have already read over that entire post before I put this on, didnt want to look an idiot - no luck there then!
I have tried to use the hard spl folder upgrade and it still only gives me the 3 colours bootscreen after a hard reset, step 2 says use bootloader mode and flash pvtemp but I've looked everywhere for pvtemp and cant find it to dl
82mike said:
I have already read over that entire post before I put this on, didnt want to look an idiot - no luck there then!
I have tried to use the hard spl folder upgrade and it still only gives me the 3 colours bootscreen after a hard reset, step 2 says use bootloader mode and flash pvtemp but I've looked everywhere for pvtemp and cant find it to dl
Click to expand...
Click to collapse
with SPL information that you said. It said, that your Device is not HARDSPL already.
You have to succesfully HARDSPL your Device first.
And after that you wont face anyproblem again.
Download :
PDVIET Temp
Is your Device CID Lock?
So I dl PDAViet, flash with that, run HARDSPL with my new .nbf in that file and I should be ok? No idea about CID lock, thanks for helping
82mike said:
So I dl PDAViet, flash with that, run HARDSPL with my new .nbf in that file and I should be ok? No idea about CID lock, thanks for helping
Click to expand...
Click to collapse
So you have to Flash your ROM now with PDA Viet Temp first. This will bring your device to WM5 No Vendor.
You have to flash it through bootloader mode, since your device now stuck up.
After that , HARDSPL your Device.
Read better thread from animelover. Here
If your Device is a G3, SPL Information will be changed into 2.G3.4PDA or for a G4 is 2.G4.4PDA
And after your Device HARDSPL ready. Run the Upgrade tool from My ROM. So you wont stuck up again.
It should run.
thats great, im running pdaviet now, read the page about hardspl too so i'll install this, turn on my m600 and run hardspl g4 followed by your rom - thanks!!
82mike said:
thats great, im running pdaviet now, read the page about hardspl too so i'll install this, turn on my m600 and run hardspl g4 followed by your rom - thanks!!
Click to expand...
Click to collapse
I will update the ROM. A small registry failure. Not so important actually.
Just wait .
I am uploading this ROM now.
You can Hardspl your Device first anyway.
Done!!! Hard SPL'd now says 2.g4.4pda on booting! I'll hang on for the new rom to be uploaded, if i want to change roms again to I have to run pda viet or now that I have run hardspl can I just install over the top? sorry for all the q's and thanks for all your help
82mike said:
Done!!! Hard SPL'd now says 2.g4.4pda on booting! I'll hang on for the new rom to be uploaded, if i want to change roms again to I have to run pda viet or now that I have run hardspl can I just install over the top? sorry for all the q's and thanks for all your help
Click to expand...
Click to collapse
If you have HARDSPL.
And Your SPL Information changed into 2G4.4PDA .
No need to install PDAViet again.
Just run the installer from the cooker.

Pda Blocked after flashing ! Help me please !

Good Morning,
- on my Jamin I've installed HardSpl (operation all ok)...
- after I've installed Throttle Diamond I Multilanguage ITA (operation all ok)...
- but when flashing is termined the jamin was "off" and after automaticaly "on"
but after was blocked on "3 color bootup"...
- so, after I've re-installed HardSpl (operation all ok)...
- when operation in termined the jamin was "off" and after automaticaly "on"
but after, and now, is blocked on first screen "i-mate" where are the
follows number: IPL 2.13
SPL 2.13.0000
GSM 02.19.21
is possible for you help me ?
thank you in advance and excuse me for my bad english, regards, mauro
... for exit from this situation I've removed and released the battery and
now the pda is blocked on "3 color bootup"...
http://www.badongo.com/file/3633747
the easiest way is flash it back to pdamobiz step1 u can flash it from the bootloader screen
after that flash it to any rom u desire
mauchit said:
Good Morning,
- on my Jamin I've installed HardSpl (operation all ok)...
IPL 2.13
SPL 2.13.0000
thank you in advance and excuse me for my bad english, regards, mauro
Click to expand...
Click to collapse
- with this information SPL 2.13.0000 Your HardSPL is unsucceses. ( SPL: G3.4DPA not 2.13.0000)
- If you flash ROM 6.1 without Hardspl device will stuck at bootloader ( tricolor)
=> flashing Romship ( or Step1, PV_temp ...) and hardSPL againt pls
Innova said:
- with this information SPL 2.13.0000 Your HardSPL is unsucceses. ( SPL: G3.4DPA not 2.13.0000)
- If you flash ROM 6.1 without Hardspl device will stuck at bootloader ( tricolor)
=> flashing Romship ( or Step1, PV_temp ...) and hardSPL againt pls
Click to expand...
Click to collapse
yes that's the problem and the exact solution
I think you mauchit are new here so (Step1, PV_temp) it also means back to WM5
thanks for your contributions,
but from the current situation (tricolor) as I go out?
what steps should I follow?
mostafa0007 reason you are, I'm new and not very experienced
mauchit said:
thanks for your contributions,
but from the current situation (tricolor) as I go out?
what steps should I follow?
mostafa0007 reason you are, I'm new and not very experienced
Click to expand...
Click to collapse
go and look @ the sticky post of mine... ^_^
Hello,
I followed your instructions which enabled me to get the pda, I returned to the original WM5, with:
IPL 2.13
SPL 2.20.000
GSM 02.47.21
OS 2.20.7.34
I rebuilt the steps to install HardSpl on pda, all went ok, but finished the procedure I find all equal:
IPL 2.13
SPL 2.20.000
GSM 02.47.21
OS 2.20.7.34
HardSpl therefore is not installed?
I tried all the files for HardSpl that I found on this forum always without success, the last that I have installed, and the procedure is finished ok, is this (ProphetSPLTool.zip x 3g) that I found here:
http://forum.xda-developers.com/showthread.php?t=401326
mauchit said:
Hello,
I followed your instructions which enabled me to g....
Click to expand...
Click to collapse
you may try to flash with " Lazy_Tool "
.....
dioxda2 said:
you may try to flash with " Lazy_Tool "
.....
Click to expand...
Click to collapse
I had already tried, I Try now, unfortunately, clicking twice on upgrade.cmd not open the program on the PC, I can not (on the pc I have windows xp) ...
mauchit said:
I had already tried, I Try now, unfortunately, clicking twice on upgrade.cmd not open the program on the PC, I can not (on the pc I have windows xp) ...
Click to expand...
Click to collapse
excuse if i ask silly questions, but its only to try and help. Wot exactly are the steps u did to hardspl? Did you interuprt the process or did ur device restart after hardspl? if you have followed the many good guides to get to hardpsl stage then u shuld not have problems? you have obv done aku2.2 b4 hardspl. i used Jesterz method and flashed his aku2.2 rom then hardspl, after 4 attempts it worked, try using different usb ports on ur pc/laptop, i had to try 3 out of 4 ports before it was sucessfull and remove all other usb cables from machine
I have tried in every way that I read on the forum xda but I could not install HardSPL on my jamin
mauchit said:
I have tried in every way that I read on the forum xda but I could not install HardSPL on my jamin
Click to expand...
Click to collapse
try this : http://forum.xda-developers.com/showthread.php?t=377904
Use Lazy tool. Download the full folder, remove any restriction on each program in the folder(unblock, read only etc). IF still doesnt work, open using command line. sure will work
Hi, i facing the same problem here:
IPL:1.00
SPL : 2.G3.4PDA
This mean i already on HardSPL, but how come i still not ablem to flash it to WM6... already try many ROM including jumpSPL. Manage to complete the flashing but after that it will stuck at Qtek screen...
timmymarsh said:
try this : http://forum.xda-developers.com/showthread.php?t=377904
Click to expand...
Click to collapse
I've tried, even with two different computers, but I can not to open the file Prophet Tools.exe and then I will not start with the procedure...
thank you four your suggestion...
rahulganatra said:
Use Lazy tool. Download the full folder, remove any restriction on each program in the folder(unblock, read only etc). IF still doesnt work, open using command line. sure will work
Click to expand...
Click to collapse
I've tried, with two different computers in every possible way, but I can not open the file Upgrade.cmd, and therefore does not start the procedure ...
anyway tanks for your suggestion ...
saints5354 said:
Hi, i facing the same problem here:
IPL:1.00
SPL : 2.G3.4PDA
This mean i already on HardSPL, but how come i still not ablem to flash it to WM6... already try many ROM including jumpSPL. Manage to complete the flashing but after that it will stuck at Qtek screen...
Click to expand...
Click to collapse
I think that if you have already configured 2.G3.4PDA pda you can install the new rom favorite ...
what problem have you exactly?
this post only for show pda and current configuration...
mauchit said:
I think that if you have already configured 2.G3.4PDA pda you can install the new rom favorite ...
what problem have you exactly?
Click to expand...
Click to collapse
The problem is, whatever ROM i tried, i will complete flashing 100% but it will stuck at Qtek screen forever...
If i flash back to shipped ROM, is end up ok, but no sound no camera.... why ? Somebody pls help....

Categories

Resources