Related
I finally got my HTC programmed and working. Everything with it is great, except now it cannot connect to the internet.
I get two kinds of error messages- initially it kept telling me that my username or password was wrong..... I couldnt find a place to enter either of those [not that i knew what they should be anyway], and I've never had this problem on my other HTC's. Now its telling me that it cannot connect for an unknown reason and that i should change the settings if needed or reset the device according to manufacturer's documentation....
What should I do?
I upgraded to wm6.1 last night, and im running USCC as my carrier.
It was suggested to me that i enter ##778 mode and change some settings there, but i do not know the MSL for my area.
Any idea where to find that?
Thanks.
Not sure if these will work but found them when I was looking for my MSL.
Use this method. I don't know who found it, but credit goes to them.
Change the following registry entries in:
HKEY_LOCAL_MACHINE\SOFTWARE\HTC\ATDbgLog
Enable: 1
LogMode: 1
* Wait a about 10 minutes (more time will not hurt), and soft-reset.
* Check to see that the file \Atlog\ATDbg0.txt has been created.
* Return the values back to what they were (most likely 0) waiting the same amount of time as above.
* Look in the ATDbg0.txt file and you should see a log of commands sent to the CDMA radio and there should be something like this somewhere in the file:
~~~~~~~~~~~SNIP~~~~~~~~~~~~
00:00:00 Tx:AT+HTC_RMSL=0\r
00:00:00 Rx:+HTC_RMSL: (###THIS WILL BE THE MSL###)\r\n0\r
00:00:00 Tx:AT+HTC_ROTKSL=0\r
00:00:00 Rx:+HTC_ROTKSL: 123456\r\n0\r
~~~~~~~~~~~SNIP~~~~~~~~~~~~
The numbers next to the Rx: +HTC_RMSL line should be your MSL
OR
Do a search for BAFMSL. It's a universal SPC code finder tool.
It requires .net 3.5, and tends to fail randomly, but so far has worked on 8 of 10 phones I have tried it on.
BTC
http://www.rimweb.in/forums/index.php?showtopic=17301
=] Awesome. This is just what I needed. Thanks.
HTC MSL
I finally got my HTC programmed and working. Everything with it is great, except now it cannot connect to the internet.
I get two kinds of error messages- initially it kept telling me that my username or password was wrong..... I couldnt find a place to enter either of those [not that i knew what they should be anyway], and I've never had this problem on my other HTC's. Now its telling me that it cannot connect for an unknown reason and that i should change the settings if needed or reset the device according to manufacturer's documentation....
What should I do?
I upgraded to wm6.1 last night, and im running USCC as my carrier.
It was suggested to me that i enter ##778 mode and change some settings there, but i do not know the MSL for my area.
Any idea where to find that?
Thanks.
Last edited by MysticThunder; Today at 01:38 AM.. Reason: new title.
Should be as simple as 000000. Same as Verizon...I just did mine, hope it works....KC
On my Titan all I did after upgrading the rom was create a new connection, called it broadband, entered #777 as the number, and my phone number followed by @vzw3g (password blank, check save password) and it worked fine.
MysticThunder said:
I finally got my HTC programmed and working. Everything with it is great, except now it cannot connect to the internet.
I get two kinds of error messages- initially it kept telling me that my username or password was wrong..... I couldnt find a place to enter either of those [not that i knew what they should be anyway], and I've never had this problem on my other HTC's. Now its telling me that it cannot connect for an unknown reason and that i should change the settings if needed or reset the device according to manufacturer's documentation....
What should I do?
I upgraded to wm6.1 last night, and im running USCC as my carrier.
It was suggested to me that i enter ##778 mode and change some settings there, but i do not know the MSL for my area.
Any idea where to find that?
Thanks.
Click to expand...
Click to collapse
there are a few settings in you need to make sure are corect in the m ip settings of the phone after u press ##778. I am using uscc and had the same issue. so I know this to be a factor after updating roms. Below are the correct settings for your m ip
Number of Profiles : 6
Active User Profile Index : 0
MIP_MODE : Mobile IP Prefered
MIP Registration Retries : 1
MIP Registration Retry Timeout : 2000 ms
MIP Pre-Registration Timeout : 3
Mobile Node-HA Authentication : Enable
Send a Registration Request Only in Use : Enable
Dormant Hanfoff Optimization: Enable
I cant stress enough... these need to be exact with uscc... dont forget to run the uscc carier cab.
If you want to have EVDO when it comes to your areas as well, under Security Settings, make sure the HDR username is your [email protected], and the ESN is in hex and all capital letters. The HDR Password is your ESN the same as above but no @uscc.net on the end.
Below this screen is also the ppp username and password, they should be your phone#@uscc.net and your phone # as the password.
These 2 settings are also necessary for data to work correctly.
BTC
Hi everyone, PLEASE READ PLEASE READ STEP BY STEP i was reading and a lot of people have questions about going to metropcs and nobody give them really good help, so i decided to make this post for you guys but please please do not post me asking how to do it in other htcs phone or worst in samsungs, lgs, etc etc I AM DOING IT THIS ONLY FOR HTC RAPHAEL or 6850 or touch pro cdma what ever you want to call it. ok so lets get start it. you have either two options:
1. Install the Hard-SPL (to unlock the phone), Install custom radio, Install custom rom, Install and modify files to make it work in Metropcs internet,mms etc. and finally take it to metropcs pay between $40 to $60 box so they flash it and you have already the phone working with everything. (recommened for dummies)
2. Install the Hard-SPL (to unlock the phone),Install custom radio Install custom rom, Install and modify files to make it work in Metropcs internet,mms etc. and Flash the HTC 6850 Touch Pro MEID and ESN to Clone the phone (i assume you have one phone already working on metropcs and you dont want to use the phone anymore so you clone it hehehehe.
--------------------------------------------------------------------------
1.Option. Download this file first:
http://www.4shared.com/file/140639926/7fa190d6/TP_ESN_FILES2.html
Important:
first, if you have GSM Touch Pro/Raphael (NOT CDMA, NOT SPRINT/VERIZON/ALLTEL/TELUS/BELL), this will brick your device.
to download a compatible hardspl package for gsm touch pro you can go to forum.xda-developers.com.
but if you have CDMA Touch Pro/Raphael, then you have to use this hardspl, not the one at xda-developers!!!
preparations before flash:
1) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
2) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
3) now decide which Hard-SPL you want to flash. if you have Verizon, flash VZW package (from verizon attachment). if you have Sprint, Telus or Alltel or Bell, flash default package (Raphael_CDMA_HSPL_037.zip).
instructions:
1) extract Hard-SPL Raphael_CDMA_HSPL_037.zip
2) you must Have Phone Synced with PC in Windows Mobile!
3) run HardSPL exe that you extracted before.
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) it should go to tricolour screen now and say 0.37.C-SSPL or for Verizon devices it should say 0.35-C-SSPL.
6) SPL flashes, device automatically reboots, job done.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.37.CMONEX MFG.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned on, press and hold the volume down button along with the power button, then press the reset button with the stylus tip, then release the volume down and power buttons when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the SSPLManual.zip attachment to the device and run it. then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
make sure to get SSPL-Manual specifically for Verizon phones from the verizon package.
NOTE 3: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is also available here.
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the Hard-SPL.
NOTE 5: use Relocker *only* if you need to return the phone for warranty. only use it as last step - after reflashing stock OS and radio. Default relocker is for Sprint etc, Raphael_CDMA_VZW_Relocker in the verizon package is for Verizon touch pro's.
(Please Donate to the CDMA Raphael Project Team - http://shorl.com/frastijeketrebo - Thanks!! )/ source
Next.Next.
we need to install the Radio, (make sure the phone is recognized by microsoft sync) i relized that the better one out there for metropcs is Telus v1.04.05V thats why i put it in my rar file.
1. extract Telus v1.04.05V and run ROMUpdateUtility
2. install it
3. when is done make sure the radio is v1.04.05V (in the dilaler press menu then press phone information and look for Radio.)
Next.
Install the rom of your chooise.I recommend for metropcs either mightyrom
(http://forum.ppcgeeks.com/showthread.php?t=52695) or NFSFAN's Custom WM6.5 ROMs (http://forum.xda-developers.com/showthread.php?t=516509) a lot of people ask for a custom rom for metropcs and thats not necesary to have almost every raphael cdma rom out there is compatible with metropcs.
-Elite Rom RC1 choose telus
http://forum.ppcgeeks.com/showthread.php?t=72401
-NFSFAN's Custom WM6.5 ROMs.
http://forum.xda-developers.com/showthread.php?t=516509
-www.MightyROM.com
http://forum.ppcgeeks.com/showthread.php?t=52695
-HAZE V1.6 Native 6.5 Kernel.
http://forum.xda-developers.com/showthread.php?t=561931
-Reflectionist Rom V0.6
http://forum.xda-developers.com/showthread.php?t=562337
-Black Dragon Titanium Rom 23420
http://forum.xda-developers.com/showthread.php?t=547846
-alpha build 1.5
http://forum.xda-developers.com/showthread.php?t=559640
-JUICY 8
http://forum.xda-developers.com/showthread.php?t=518466
-WM 6.5 21501 djbeames
http://forum.xda-developers.com/showthread.php?t=509544
-grooveROM 5
http://forum.xda-developers.com/showthread.php?t=534888
-EnergyROM 'Photon'
http://forum.ppcgeeks.com/showthread.php?t=69545
-Calkulin's Visual
http://forum.ppcgeeks.com/showthread.php?t=87040
-MurdaROM
http://forum.ppcgeeks.com/showthread.php?t=87040
-SsS-ROMv0402
http://forum.ppcgeeks.com/showthread.php?t=68755
-NK-All Carriers-RZ Baseline 3.2
http://forum.ppcgeeks.com/showthread.php?t=81038
-Demolition 6.5
http://forum.ppcgeeks.com/showthread.php?t=66799
-Psyki 4
http://forum.ppcgeeks.com/showthread.php?t=66993
-JD's Clean
http://forum.ppcgeeks.com/showthread.php?t=73860
-Sac ROM
http://forum.ppcgeeks.com/showthread.php?t=68734
-SilenceROM
http://forum.ppcgeeks.com/showthread.php?t=84859
-eRice
http://forum.ppcgeeks.com/showthread.php?t=46965
-MERDIN'S WMPro
http://forum.ppcgeeks.com/showthread.php?t=50716
-StarROM 2.0
http://forum.ppcgeeks.com/forumdisplay.php?f=68&order=desc&page=2
-TruXt v5.1
http://forum.ppcgeeks.com/showthread.php?t=82653
-Chaos ROM
http://forum.ppcgeeks.com/showthread.php?t=75974
-Longhorn ROM
http://forum.ppcgeeks.com/showthread.php?t=65849
-Sceptre Rom 3.4 SenseSuite
http://forum.ppcgeeks.com/showthread.php?t=75215
-dcd's hermann ROM 2.00
http://forum.ppcgeeks.com/showthread.php?t=69754
-091409 XOR
http://forum.ppcgeeks.com/showthread.php?t=84394
-CFAY 1.5.5
http://forum.ppcgeeks.com/showthread.php?t=50471
-Juggalo TP ROM v0.08B (choose telus)
http://forum.ppcgeeks.com/showthread.php?t=49341
-JonRom Version 2.55
http://forum.ppcgeeks.com/showthread.php?t=79924
-FuzeBerry II
http://forum.ppcgeeks.com/showthread.php?t=62786
-midNIGHT v5.5
http://forum.ppcgeeks.com/showthread.php?t=75032
-Copper v.0.0.0.1
http://forum.ppcgeeks.com/showthread.php?t=64242
-Ivan's ROM 1.9.S.V
http://forum.ppcgeeks.com/showthread.php?t=48463
-dB_ROM WM 6.5
http://forum.ppcgeeks.com/showthread.php?t=67426
-FALLEN ROM
http://forum.ppcgeeks.com/showthread.php?t=63479
-Yay 4 Juggs
http://forum.ppcgeeks.com/showthread.php?t=61274
-Jmz Rom 3.0
http://forum.ppcgeeks.com/showthread.php?t=61953
-FireROM
http://forum.ppcgeeks.com/showthread.php?t=73395
-KK's Loaded ROM v1.8
http://forum.ppcgeeks.com/showthread.php?t=52307
-Tech1 MultiMedia
http://forum.ppcgeeks.com/showthread.php?t=72782
-JOKER ROM
http://forum.ppcgeeks.com/showthread.php?t=68213
-DREAM Full and Lite
http://forum.ppcgeeks.com/showthread.php?t=49338
-THE LAST-Forgiven
http://forum.ppcgeeks.com/showthread.php?t=70059
-NSFW College ROM
http://forum.ppcgeeks.com/showthread.php?t=69371
-PhantomROM
http://forum.ppcgeeks.com/showthread.php?t=62796
-JowPod
http://forum.ppcgeeks.com/showthread.php?t=69269
-Merdin's
http://forum.ppcgeeks.com/showthread.php?t=59780
-PsykiROM v1.0
http://forum.ppcgeeks.com/showthread.php?t=65145
-nueROM-S
http://forum.ppcgeeks.com/showthread.php?t=42777
i think thats it if you know another one just let me know i will post it.
Finally the most difficult part in this process.
set up the internet, mms and GPS
download this file:
http://www.4shared.com/file/140658132/5838a6f3/MetroPCS.html
-connect your phone to de pc and install get spc in the phone
-run it and press on get spc, press ok or yes and it will display six digit number write this number down because we will need it.
-in the dialer type ##778# click on edit and write the six digit number that you wrote down.
-next a screen that says EPST and below that say Display will appear.
-we well need to modify some of this ones
DISPLAY
-NAM NAME write you ten digit numer
-SCM write the first two digit of area code of the phone number(if appears to be editable if not leave it like that)
-MSID write your ten digit phone number
click in view info and go to
NAM SETTINGS
-NAM NAME write your ten digit phone number
-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516
-MIN2 first three digits of your phone number (area code)
-MSID write your ten digit phone number
-MCC 310
-MNC 27
-NMSI 27and write your ten digit phone number
-IMSI 31027and write your ten digit phone number
Part 2
click in view info and go to
CDMA SETTINGS
-A-SYS PRIMARY 283
-B-SYS-PRIMARY 384
-A SYS-SECUNDARY 691
-A SYS-SECUNDARY 777
-MON_TERM_FOR_HOME ENABLE
-MON_TERM_FOR_SID ENABLE
-MON_TERM_FOR_NID ENABLE
-EVRC ENABLED DISABLED
-HOME PAGE VOICE 13K
-HOME ORIG VOICE 13K
-ROAM ORIG VOICE 13K
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535
click in view info and go to
MODEM SETTINGS
-SLOT CYCLE 1
-PREFERRED SERVING AUTO
-PREFERRED MODE AUTO
-HDR HYBRID ENABLE
-CLEAR ALL MRU NO
click in view info and go to
-PRL
-UPDATE PRL FILE AND YOU HAVE TO TRANSER THE FILE 02001 THAT IS IN METROPCS.RAR AND SELECT THAT ONE
click in view info and go to
SECURITY
-HDR AN AUTH USER ID [email protected]
-HDR AN AUTH PASS metropcs
-PPP USER ID [email protected]
-PPP PASS metropcs
click in view info and go to
DATA PARAMETERS
-PACKET DIAL #777
click in view info and go to
M.IP SETTINGS
-NUMBER OF PROFILES 6
-ACTIVE USER PROFILE 0
-MIP_MODE SIMPLE IP ONLY
-MIP REGISTRATION RETRIES 1
-MIP REGISTRATION RETRY 2000 ms
-MIP PRE-REGISTRATION TI 30
-MOBILE NODE-HA Disable
-SEND A REGISTRATION Enable
-DORMAND HANDOFF Disable
click in view info and go to
M.IP DEFAULT PROFILE
-ENABLE PROFILE Enable
-NAI [email protected]
-MN HA SPI SET Disable
-MN HA SPI VALUE 0
-MN AAA SPI SET Disable
-MN AAA SPI VALUE 0
-HOME ADRESS 0.0.0.0
-PRIMARY HA ADDRESS 255.255.255.255
-SECUNDARY HA ADDRESS 255.255.255.255
-HA SHARED SECRET metropcs
-AAA SHARED SECRET metropcs
-DMU 0
-MN 0
make sure that
M.IP CUSTOMER PROFILE 1,2,3,4,5,6 are Disable
click menu ok and reset.
when the phone resets please install Metro WAP and Arcsoft 5_0_70_24 from METROPCS.CAB
also after everything is done please dont forget to take the phone to metropcs so they can put you nam in the metropcs system thats what they call flash the phone to metropc.
Internet Sharing - tethering big thanks to silvaadams from ppcgeeks
make sure you have internet on your phone ofcourse
start up comm manager and click your internet sharing button thingy lol
click connect on the lower left hand corner
wait for phone to say check usb connection
then connect phone to usb and usb to computer (should say connected)
open internet explorer
go to settungs
go to internet options
go to connections tab
click on lan settings
click proxy server check use proxy blabla
then type wap.metropcs.net port 3128
then ok
open up firefox
once open go to tools> options> advanced> network
under network click settings
select manual proxy config
under http proxy type
wap.metropcs.net [port:] 3128
then check off "use this proxy server for all protocols"
--------------------------------------------------------------------------------------------------------------------------------------------
2.option. HTC 6850 Touch Pro change MEID change ESN Repair / Clone Solution i assume you have a phone already in metropcs so u can clone it and avoide paying $40 or $50 dollars activation fee.
Download this file first:
http://www.4shared.com/file/140639926/7fa190d6/TP_ESN_FILES2.html
PLEASE READ SOME DIFFERENCES FROM OPTION 1.
Important:
first, if you have GSM Touch Pro/Raphael (NOT CDMA, NOT SPRINT/VERIZON/ALLTEL/TELUS/BELL), this will brick your device.
to download a compatible hardspl package for gsm touch pro you can go to forum.xda-developers.com.
but if you have CDMA Touch Pro/Raphael, then you have to use this hardspl, not the one at xda-developers!!!
preparations before flash:
1) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
2) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
3) now decide which Hard-SPL you want to flash. if you have Verizon, flash VZW package (from verizon attachment). if you have Sprint, Telus or Alltel or Bell, flash default package (Raphael_CDMA_HSPL_025_MFG).
instructions:
1) extract Hard-SPL Raphael_CDMA_HSPL_025_MFG
2) you must Have Phone Synced with PC in Windows Mobile!
3) run HardSPL exe that you extracted before.
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) it should go to tricolour screen now and say 0.25.C-SSPL or for Verizon devices it should say 0.35-C-SSPL.
6) SPL flashes, device automatically reboots, job done.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.25.CMONEX MFG.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned on, press and hold the volume down button along with the power button, then press the reset button with the stylus tip, then release the volume down and power buttons when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the SSPLManual.zip attachment to the device and run it. then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
make sure to get SSPL-Manual specifically for Verizon phones from the verizon package.
NOTE 3: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is also available here.
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the Hard-SPL.
NOTE 5: use Relocker *only* if you need to return the phone for warranty. only use it as last step - after reflashing stock OS and radio. Default relocker is for Sprint etc, Raphael_CDMA_VZW_Relocker in the verizon package is for Verizon touch pro's.
(Please Donate to the CDMA Raphael Project Team - http://shorl.com/frastijeketrebo - Thanks!! )/ source
-install the radio that is on TP ESN FILES2\RAPHING
-install the rom of your choise from Option 1
-now MAKE SURE YOU WRITE DOWN OR BACK UP ALL YOUR DATA SETTINGS BEFORE YOU DO THIS JUST IN CASE
- download
http://www.4shared.com/file/140658132/5838a6f3/MetroPCS.html
- install WModem_Driver_Installer_v1.2.2.4_WWE
-make sure to install get spc on the phone run it and get ur spc code
-disconnect phone
-put phone in diag mode (dial ##3424#) wait until the white screen disapear and connect your phone to ur pc
-now install all the drivers but maybe it will tell that u need qcmdmxp or another one so just select files from Program Files\HTC\WModem_Installer\WinXp
-Disable USB connection in Active Sync by unchecking checkbox in Connection Settings of Active Sync
-Hold Pwr and Vol Down buttons and push reset button to boot the phone in bootloader mode.
Part 3
-Run mtty.exe from TP ESN FILES2
-Leave every setting alone apart from change the 'Port' to 'USB' in yhe drop down box. Hit OK.
In the window that opens up, type the following commands (All Commands are case Sensitive) Hit enter after typing each one. You may see nothing while typing, just type carefully.
1. rtask a
12 echo_on
3. readCID
4. writeCID 00000000
5. readCID (window should return CID as 00000000)
6. rtask c (will probably give and error - mine did!)
-Soft reset phone and close mtty.
-Re-enable USB connection in connection settings of ActiveSync. Make sure phone is 'connected' to ActiveSync, you might have to unplug and plug in usb to make this happen.
-Flash phone with Raphael_CDMA_HSPL_037.exe
-Let phone restart.
-disconnect phone
-put phone in diag mode (dial ##3424#) wait until the white screen disapear and connect your phone to ur pc
-download http://rapidshare.com/files/210789608/QPST_2.7.323__2008-09-19_.rar
-open QPST configuration and click on add port
-make sure to memorize the port that says htc diagnostic that port com is really important we well use it for many things
-Launch DFS. from TP ESN FILES2
-Select your phone's com port. (top left ish) this is the port that i was talking about diagnostic port com
-Select 6950 from the HTC devices menu on the left. Before you all start, yes I know we are programming a 6850, but the secret here is that the MEID portion of the 6850 equipment file in DFS ties up to the MEID locations in the radio rom supplied (which was ported from the diamond)
-Ignore any errors at the bottom of the screen about equipment not found etc... Remember, just follow the instructions!! So, once the com port is connected, go the MEID section and type your originial metropcs phone the one you have to clone MEID(D)(decimal) it should be on the back of the phone also make sure that the original metropcs phone os turn off u dont want to turn this phone ever in your life. Ignore the pESN that it creates but do not modify it
-Click Write like 4 times and it will write it to the phone no matter what it says at the bottom of the screen.
-Close DFS and soft reset.
-now go to http://www.previo.net/meid-esn-converter.html
-type your MEID(D)(decimal) and click submit the important thing here is ESN the hex not the dec. so copy the hex one.
-Go into diag mode ##3424# again wait untill the white screen disappear and connect it usb to ur pc
-Open up the attached CDMA Workshop 2.7 cdma workshop.exe but the one is in METROPCS.RAR not the one is in TP ESN FILES2 and select the com port to connect your phone. THIS COM PORT IS THE DIAGNOSTIC PORT.
-click connect and then read
-in your phone go to dialer and type ##778# edit and type your spc code then.
-Go to the security tab in workshop and click read by the esn. It should display your current esn.
-Type the esn that the website give you the hex one. this should be your original metropcs nam number
-click write.
-Go to Nam tap and Click in Banner
-Type MetroPCS and
-click write
-now Close CDMA WS and soft reset
-now install the radio u want to use from here
http://forum.xda-developers.com/showthread.php?t=531134&highlight=radio
recommend TELUS v1.04.05V or VERIZON v1.03.03V
-when is done type in your dialer ##778# edit in the screen that says EPST and below that say Display will appear.
-we well need to modify some of this ones
DISPLAY
-NAM NAME write you ten digit numer
-SCM write the first two digit of area code of the phone number(if appears to be editable if not leave it like that)
-MSID write your ten digit phone number
click in view info and go to
NAM SETTINGS
-NAM NAME write your ten digit phone number
-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516
-MIN2 first three digits of your phone number (area code)
-MSID write your ten digit phone number
-MCC 310
-MNC 27
-NMSI 27and write your ten digit phone number
-IMSI 31027and write your ten digit phone number
click in view info and go to
CDMA SETTINGS
-A-SYS PRIMARY 283
-B-SYS-PRIMARY 384
-A SYS-SECUNDARY 691
-A SYS-SECUNDARY 777
-MON_TERM_FOR_HOME ENABLE
-MON_TERM_FOR_SID ENABLE
-MON_TERM_FOR_NID ENABLE
-EVRC ENABLED DISABLED
-HOME PAGE VOICE 13K
-HOME ORIG VOICE 13K
-ROAM ORIG VOICE 13K
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535
click in view info and go to
MODEM SETTINGS
-SLOT CYCLE 1
-PREFERRED SERVING AUTO
-PREFERRED MODE AUTO
-HDR HYBRID ENABLE
-CLEAR ALL MRU NO
click in view info and go to
-PRL
-UPDATE PRL FILE AND YOU HAVE TO TRANSER THE FILE 02001 THAT IS IN METROPCS.RAR AND SELECT THAT ONE
click in view info and go to
SECURITY
-HDR AN AUTH USER ID [email protected]
-HDR AN AUTH PASS metropcs
-PPP USER ID [email protected]
-PPP PASS metropcs
click in view info and go to
DATA PARAMETERS
-PACKET DIAL #777
click in view info and go to
M.IP SETTINGS
-NUMBER OF PROFILES 6
-ACTIVE USER PROFILE 0
-MIP_MODE SIMPLE IP ONLY
-MIP REGISTRATION RETRIES 1
-MIP REGISTRATION RETRY 2000 ms
-MIP PRE-REGISTRATION TI 30
-MOBILE NODE-HA Disable
-SEND A REGISTRATION Enable
-DORMAND HANDOFF Disable
click in view info and go to
M.IP DEFAULT PROFILE
-ENABLE PROFILE Enable
-NAI [email protected]
-MN HA SPI SET Disable
-MN HA SPI VALUE 0
-MN AAA SPI SET Disable
-MN AAA SPI VALUE 0
-HOME ADRESS 0.0.0.0
-PRIMARY HA ADDRESS 255.255.255.255
-SECUNDARY HA ADDRESS 255.255.255.255
-HA SHARED SECRET metropcs
-AAA SHARED SECRET metropcs
-DMU 0
-MN 0
make sure that
M.IP CUSTOMER PROFILE 1,2,3,4,5,6 are Disable
click menu ok and reset.
when the phone resets please install Metro WAP and Arcsoft 5_0_70_24 from METROPCS.CAB
reset it one more time
finally call *228 wait untill the spanish thing is over and press 1 then wait 2 seconds press 1 again wait 2 seconds and press 1 again this will make u talk to custumer service tell them u are having trubles with ur phone and you need to reprogram your phone sometimes they are lazys and dont want to do it so insinst. please give them your MEID(D) decimal number and depend of your phone they will tell you do this or do that but dont do it write everything down and tell them yes ok i done hahaha in my case of kyocera melo they told me to do this type 111111 go to options service go to program 587846 type mdn MYPHONENUMBER type min 3234764516 and type home sid 6503 after that they told me im done just soft reset it and that its but when i hang up i didn do it and please dont do it go to dialer and type ##778# edit and we need to make some changes.
DISPLAY
-NAM NAME write the program number they give u my case 587846
-SCM write 58
click in view info and go to
NAM SETTINGS
-NAM NAME write the program number they give u my case 587846-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516 type the min number they give in my case 3234764516 323 is the area code but when u restar the phone this dissapear
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535 here just change the the SID for the one they give you my case 6503 the other one leave it as 65535
soft reset and you are ready to go.
Internet Sharing - tethering big thanks to silvaadams from ppcgeeks
make sure you have internet on your phone ofcourse
start up comm manager and click your internet sharing button thingy lol
click connect on the lower left hand corner
wait for phone to say check usb connection
then connect phone to usb and usb to computer (should say connected)
open internet explorer
go to settungs
go to internet options
go to connections tab
click on lan settings
click proxy server check use proxy blabla
then type wap.metropcs.net port 3128
then ok
open up firefox
once open go to tools> options> advanced> network
under network click settings
select manual proxy config
under http proxy type
wap.metropcs.net [port:] 3128
then check off "use this proxy server for all protocols"
thanks to englishdan from mobile-files.com, xda forum, cmonex, and everybody that makes this possible. also i download the files and i forgot most of the post that i got the files so please all the people that makes this files and aport to this excuse me for that my apologize i just want to make this easier to everybody becasue i spend days and days trying to do this thanks to the users from PPCGeeks, howardforums, and mobile-files. without this it wouldnt be possible to make this also my apologize if there is things from other forums not mentioned but i forgot most of the places and users that take infotmation off once again thank u.
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
hey bro
dude i work my ass off to get this work for 7 days sleeping only 3 or 4 hours i put all this info togheter four you guys and then u re telling me this, no where u will find this and i post at the last thanks to the guy who help me the most but if you go to his profile and see the post http://www.mobile-files.com/forum/showthread.php?t=111584 u will see how empty is a lor of questions and a lot of people that are confused but if you look what i write is so complete that everybody will understand there is a lot of people that i have to thanks but if i write all the names down there will be no space in the forum read bro and i thanks to all of them i mention at the end so please shut the **** off because i work my ass off to make this post.
snail813 said:
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
Click to expand...
Click to collapse
Great Job Looser
First post...yeah! Something tells me you're like one of those off duty english teachers: cite your sources.... Suck a fat one. Drey did an excellent job trying to help others and not himself. He doesn't even have a paypal link on the bottom of the posting. I have my TouchPro on metropcs fully functioning from multiple links on ppcgeeks and xda-developers. Thanks to many.
Drey, You did great with this post man! Too bad an off duty buttwhole is around fouling things up! What a jerk off. First post! lol.
snail813 said:
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
Click to expand...
Click to collapse
Metro WAP
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
belalucf said:
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
Click to expand...
Click to collapse
If you had the phone flashed to metropcs all you have to do is input the Metro WAP settings. I did not use a cab file. First HardSPL, Archsoft MMS, then change WAP settings, and the registry.
wap
Yeah I tried inputting all the settings, then creating a new connection called metro pcs with all the port settings and stuff, which I don't even see on this guide. Because if you don't create a new connection, it wont do anything once I removed the sprint connection which I did by changing the guardian file, which allowed me to even remove it. But I was hoping that this program would I guess populate that stuff somehow, so I went through and manually put in all those settings. Still no connection
ok
ok you can do it this way put your phone in dial mode ##3424# wait until white screen turns off and open workshop 2.7 from mteropcs.rar you have to go other tab under PRL choose write and select the ppl file
when you open the browser a window will apear you have to write your [email protected] and metropcs as password
note u set this up ##778# edit Mip default profile thank u
belalucf said:
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
Click to expand...
Click to collapse
thanks bro
thanks bro for me was hard i have to go to so many forums and read and read to make this work for my little brother, i gave him this phone as a gift but in sprint and he have metropcs so i decided to read and find out how this works and after work my ass off for 1 week taking information from here there ask so many questions i decided to make all that info in one post and then this jerk tell me this bro i am doing this to help everybody the important thing here is share so other people can learn and not like me that spend hours in my pc trying to figure this out thanks bro..
stukes said:
First post...yeah! Something tells me you're like one of those off duty english teachers: cite your sources.... Suck a fat one. Drey did an excellent job trying to help others and not himself. He doesn't even have a paypal link on the bottom of the posting. I have my TouchPro on metropcs fully functioning from multiple links on ppcgeeks and xda-developers. Thanks to many.
Drey, You did great with this post man! Too bad an off duty buttwhole is around fouling things up! What a jerk off. First post! lol.
Click to expand...
Click to collapse
mmm
if the cab file that i gave u (THANKS TO RYANMONGUL6800)didnt work try to do it manually http://rferreira1.googlepages.com/revisedMogul6800tometro.pdf if stills not working try to start again first install the cab file then go to ##778# edit ur spc code then edit mip. default profile for the one i have soft reset open browser it should ask for the username [email protected] and pass metropcs if still not owrking u have to follow this
from ryanmongul6800
Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the password below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
Click view info and pick MIP Default Profile, Enable profile should be ENABLE, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 255.255.255.255, secondary should be 255.255.255.255, HA shared secret and AAA secret should be metropcs <--lowercase, DMU public should be 0, MN Authenticator should be 0.
Click view info and pick MIP customer profile 1 and make sure Enable profile is DISABLED. Now do the same with the other 4 profiles (profiles 2-5), make sure that the only profile enabled is MIP Default Profile.
Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778 call button (PST/EPST), we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to [email protected], password should be metropcs<--lower case, same for PPP user id and Password make them same as HDR.
Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both metropcs<---lowercase, then click menu OK and let it reset.
belalucf said:
Yeah I tried inputting all the settings, then creating a new connection called metro pcs with all the port settings and stuff, which I don't even see on this guide. Because if you don't create a new connection, it wont do anything once I removed the sprint connection which I did by changing the guardian file, which allowed me to even remove it. But I was hoping that this program would I guess populate that stuff somehow, so I went through and manually put in all those settings. Still no connection
Click to expand...
Click to collapse
Wap
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
hard way
ok you can try this out i have not try it so i dont know if it would work first go to control panel, then system hardware, device manager click universal serial bus controllers and unistall all of them restart your pc and it would install back the usb drivers then connect the phone diag mode if doesnt ask for drivers go to control panel, then system hardware, device manager go to ports( com & lpt) you should see htc diagnostic port if the port is below 27 we are fine if not delete all of them but do not unistall com 1. dont worry it will delete ports that u install thins when u plug things u have to install again so don worry. now if the phone ask you for drivers once u delete everything install them again but this time if still port higher than 27 go to device manager click in com 1 click update drivere install from specific locatiuon, dont search i will install have disk browse go to programs files /WModem_Installer/qcusbmdm.inf next yes ok and thats it you have it in com 1 after u done everything just delete port com 1 and it will install it after u reset the computer thank u..
u need to install WModem_Driver_Installer_v1.2.2
from metropcs.rar
try it in your friends computer or some internet cafe pcs hehehe i know bro always something happens
belalucf said:
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
Click to expand...
Click to collapse
if that doesnt work
i pretty sure it will work but just in case the methods dont work try to borrow a pc from ur friend or go to an internet cafe hehehehe
belalucf said:
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
Click to expand...
Click to collapse
thanx for all the help i had wap and mms working but internet sharing and gps didnt thanx again
GPS
cdw9800 said:
thanx for all the help i had wap and mms working but internet sharing and gps didnt thanx again
Click to expand...
Click to collapse
Do you have quickGPS installed??? This it is available on the forums and wiki just do a search. It downloads updated satellites for google and other apps to use.
metro pcs
Well i got cdma to see the htc, but when i open the browser it says provisioning data services and says it can't connect.
check
ok just please more specific which rom are you using and the steps u did
belalucf said:
Well i got cdma to see the htc, but when i open the browser it says provisioning data services and says it can't connect.
Click to expand...
Click to collapse
Awesome
I wanted to change carriers from Cricket to MetroPCS. Metro told me I would have to go to Dallas to have the Metro flash applied. Well that is a 2+ hour drive from where i am. I like Metros pricing plan. I can have 3 phones for the same amount I pay for 2 Cricket. Good job on this write up and work you have done.
Hi,
I've found many software that supposed to help in case your phone get lost or stolen.
Some were expensive, some were free, but none fitted perfectly to what I was really expecting. So I've made my own.
The closest in terms of functionnalities (and price) is Remote Tracker, but it requires .NET 3.5 which is not installed on my WM6.5 phone, and honestly, it's a very fat dependency.
The idea is that you install this software (no CAB, simply copy the 2 files on your phone), and run it once to set up the configuration. Then forget it.
In the case the phone is stolen, the software will send you a SMS with the thief's phone number, it's GPS position, the CellID in case the GPS pos is not available.
You'll then be able to act on your phone remotely by sending it some SMS (described in documentation).
The features that makes this software unique are:
It's possible to destroy all your personal data remotely (call log history, contact, emails, SMS, calendar, owner info, storage card) -> help social engineering to get back your phone.
It's possible to make the phone send you back the call history and the sim contacts.
Slut mode (see the documentation for details).
WOULDYOUSHUTUP mode (where the phone is very very nasty).
All other tracking software features...
This software is open C++ source (GPLv3), small (75ko with no dependencies), and free.
You'll find it at http://dsmp.sf.net (documentation on that page)
Or the direct link is attached.
Beta tester welcome (I've tested all functions already, but, you know what software development is....)
Some remarks for those who don't read threads:
whereRU: requires you to have at least a .wav file in your windows ring folder. I thought all phone had at least one .wav based ring. In 64kb, I haven't included a MP3/AAC/MP4 player.
owner: This is what I said in my first posts. Microsoft didn't feel it was interesting to document how to retrieve owner info. So, almost all manufacturer have made there own proprietary stuff. I've a HTC phone, so I've checked the code work for HTC. If you have more information about where your phone store its owner information in registry, I can add your phone support.
contact: On the main config dialog, in the combo box where you can enter the phone number to contact, you'll have a phone number list. It's the same list as returned in the "contact" command. So if you don't have such list in the config dialog, then this means that either you don't have any contact on your SIM card, or it's not working (in that case PM me).
Please read the website http://dsmp.sf.net
To install the software:
1. Extract the zip file (either on your phone, or on the PC, and then copy the 2 files from archive to your phone)
2. Run the extracted exe on your phone. If you have signed warning say yes.
3. Set up your configuration (DON'T check "Don't show this screen anymore")
4. If you have a GPS in your device, go outside to make sure the GPS is working with the configuration you've made
5. Enter a (not yours) phone number in the SMS par edit/combobox
6. Enter a password in the edit box on the bottom
7. Click done => Say yes.
8. Start the software again, enter the previous password in the field on the botton to unlock the dialog, then click on "Configuration done, install now"
9. If you have signature warning for the DLL say yes.
10. It should display "Installation done". You can then send yourself a SMS with the right format to check if it's working.
11. If it's working, delete the SMS you've just sent from your outbox, and trash, and then start the software again and check "Don't show this screen anymore". You'll have to click "Configuration done" again, but this times, you shouldn't have any warning.
12. If it's not working, well post on the forum.
Changelog:
- Added "allow" command so it's possible to use multiple allowed SIM card. Setup the software as described above, and then change your card. You'll get a SMS with the new number (if not, your configuration isn't good). Then reply with the command "dsmp # allow # password" with no space between #. This SIM card is then allowed. You can have up to 4 allowed SIM card.
- Fixed an installation bug on non-french phone. Sorry, I've been lazy, and it should be fixed.
- Added support for "Dsmp" in addition of "dsmp" as trigger code
- More owner info retrieved for HTC phones
Please go to sf.net page ( http://dsmp.sf.net ) if you want to get the debug version or source code.
sounds impressive ! i might give it a try!
good work !
CDMA diamond running a 6.1 rom. got to step 8 and each time I enter in my password and close my keyboard the screen where the keyboard was (touchpal is my SIP) shows the screen behind what it should show. hope that makes sense. how do I uninstall this software?
also, I dont see anywhere where it says what WOULDYOUSHUTUP mode is.
WOULDYOUSHUTUP is what happen when you send a sms with "whereRU". The phone rings at max volume for 60s with no possible way to stop it, even if it was in silent mode.
Useful when you've lost your phone nearby, (it won't stop until you've found it, or 60s later), or, as intended, to become a nuisance to any thief in the middle of the night.
To uninstall the software you must click on "Zap" button, but you need your password for that. BTW if you haven't done step 8, you don't need to uninstall, as the installation proceed only when you click "Configuration done" button.
If the software doesn't accept the password you've set at step 6, then it's likely that it was entered wrong at first? I'll PM you about this, if you don't mind.
installed it, and tested a whereRU with another phone, doesn't work. :\
I've answered with specific details by PM. I trying to understand why installation didn't work for you. I'll update the post with the informations you'll give me.
sounds really nice.
I just see some problems. These problems apply to any anti-theft program :
If you have a pin-lock for the device (not sim card lock, the built-in windows lock), the thief will not be able to change anything (owner, ...). He can only change the sim and try to boot, what will of course fail. As this fails (without unlocking phone-lock, no dialing), he will not be able to establish a connection to his mobile network and you will not get his number (?!)
As hard-reset is always possible (every thief can google ) w/o the program being cooked into rom, this software is senseless if you can't cook roms. I can't
If I understood it correctly, you would need to edit the 2 files to your needs (with numbers aso) at first instance and afterwards cook them into rom. This has to be done by each end-user each time he flashes a new rom and cant be done by rom-chef because he doesnt know your data.
Isn't it possible to make that wireless? E.g. you specify an email there and the programm will at first boot after hardreset (after cooking into rom) establish a connection to a server (or mail to specified mail) to download the details (cell number, pw, ...) you entered in the server? ^^
You only can enter one own cell number. Bad if you sometimes switch the sim's.
Would be better to implement that from remotetracker:
SIM Cards: you can set up to four known SIM cards. If you, or anyone, change the SIM card to an unknown card, your emergency number and e-mails will receive a message alerting you about the change and with the new number
Click to expand...
Click to collapse
* If you use this kind of software, you'll want to make your thief believe he succeed owning your phone. If you PIN-lock your device, then the thief will have to hard reset the phone to use it, defeating the whole process.
* In my previous phone (Universal), there was a Extended ROM made by the operator that survived hard reset. I've used that ROM by that time.
Now, you're perfectly right, with a single ROM, the hard reset kills the software. Your idea of using a external server is genius. I guess I'll add this, using your device ID (which doesn't change whatever the ROM) (or IMEI), to retrieve the config for your phone. The config will be saved on a server, and the config can be sent back by SMS (so even if the thief doesn't have network contract, it'll work).
* You switch SIM ? Is 2 SIM okay ?
I wanted the software to be extremely simple to setup, so it detected the IMSI by itself.
Now, if you need to store 2 IMSI, it'll need another edit box to let you enter the IMSI numbers.
I can add a new command "allow" that, when you've inserted your second SIM, will allow the new IMSI upon receiving.
Let me think about this.
Yep, but I won't -of course- disable excellent built-in security mechanisms to make it *perhaps* easier to get the phone back just in case someone steals my phone.
The phone-lock is ideal to keep away random access to private and corporate data from other persons (friends, aso).
Despite the lack of some functions I installed the program yesterday and it doesn't work as thought:
The program loads after each reset again with the config screen
The program is active in task manager (dsmp.exe)
The sent commands aren't executed. If I send the commands (e.g. rst or whereRU) to the phone, the display turns on but nothing happens.
(perhaps the first 2 problems are caused because I did not hide the program yet with "Do not show this anymore" Not sure about that )
You could just say at setup: Now turn off the phone and enter your other sim and start the setup again to detect the second sim
hi popol256,
is there a chance for a very thin application, that after installed on a phone (e.g LEO) makes JUST the following:
- receiving a predefined SMS lock's the phone and encrypts the msd card.
To unlock the phone and decrypt the msd card, just a so called "master password" or whatever needs to be input.
That's all
thank you,
/s1
Locking the phone is possible (but again, if you lock the phone, then the thief will hard reset it).
Encrypting the microSD card is not, I think.
So far, I think you need to either encrypt it at first use (all WM6 phone have this as a base feature). When you have data on it and want to encrypt, it's almost impossible as you'll need the same free space on your device as your card size to store the encrypted version.
(Or if only encrypting content, you'll need to reserve half your card size for the "possibly" encrypted archive).
I guess the best method for you if to use the storage card encryption feature of WM + pin lock.
bliblablub said:
Yep, but I won't -of course- disable excellent built-in security mechanisms to make it *perhaps* easier to get the phone back just in case someone steals my phone.
The phone-lock is ideal to keep away random access to private and corporate data from other persons (friends, aso).
Click to expand...
Click to collapse
You are right. The only way to have both would be to cook your own ROM with the software inside.
bliblablub said:
Despite the lack of some functions I installed the program yesterday and it doesn't work as thought:
The program loads after each reset again with the config screen
The program is active in task manager (dsmp.exe)
The sent commands aren't executed. If I send the commands (e.g. rst or whereRU) to the phone, the display turns on but nothing happens.
(perhaps the first 2 problems are caused because I did not hide the program yet with "Do not show this anymore" Not sure about that )
Click to expand...
Click to collapse
Yes the 2 first issues are because the config says to show the dialog.
The third issue means that the software isn't installed well.
I've only tested it on my phone, and I might have done something wrong.
There is a debugversion here
Extract this version to your card, then run the exe in it, and click "Zap". Then wait for few minutes, and reset your phone (this is to make internal mail application to release its lock on the interceptor DLL).
Run the software again, and set the config, click "done" or "ok", and send yourself a SMS (don't need to install this version, it runs from the card).
You should get 2 message box, the first one contains the path to the software (end in .exe), and the message you've sent, and the second only contains the command you've sent. If this work, well, I'll have to double check the release version.
bliblablub said:
You could just say at setup: Now turn off the phone and enter your other sim and start the setup again to detect the second sim
Click to expand...
Click to collapse
Yes, it's the basic idea (in fact, as soon as you insert your second SIM, you'll receive a SMS, but you'll then send an "allow" command to add this IMSI in the allowed IMSI list). I'm adding this.
Hehe, got the following error running the debugversion:
CmdLine (OK)
(empty)
Click to expand...
Click to collapse
Can't load DLL (OK)
\Carte de stockage\DSMPI.dll
Click to expand...
Click to collapse
Error (OK)
Can't register the message interceptor DLL
Please make sure the DSMPI.dll is in windows folder
Click to expand...
Click to collapse
Ok, my fault then, I've used French name for the path. Let me few hours to compile a new version with the regular name, I'll post back here.
Ok, I've added the "allow" command for multiple sim card. The idea is simple, configure your software as said in the first page, then change your sim.
You'll received a SMS to the number you've set up. Then send a "allow" command with your password, and the new SIM is allowed you'll never receive a SMS again.
bliblablub,
Please run the version you have on your storage card, and click "Zap" button to uninstall it.
Then delete the 4xxxxxxxxx_dfed_p (xxxxx is a hexadecimal number) from your storage card (file format changed).
Then download the updated DSMP.zip version from the main (or the official) page again.
There was a bug with the file path that should be fixed now with the release version.
Thank you for your patience.
popol256 said:
bliblablub,
Please run the version you have on your storage card, and click "Zap" button to uninstall it.
Then delete the 4xxxxxxxxx_dfed_p (xxxxx is a hexadecimal number) from your storage card (file format changed).
Then download the updated DSMP.zip version from the main (or the official) page again.
There was a bug with the file path that should be fixed now with the release version.
Thank you for your patience.
Click to expand...
Click to collapse
I can't uninstall it because it was not installed I guess (debug - storage). See errors on post before
Somehow I managed to uninstall the internal version. Needed several attempts.
Now installed again on phone and again nothing happens with whereRU and any other command except lcd turning on
Does it work fine?
Any opinion?
Nice, nice, nice. Sounds like the app I was always looking for. I will download and try. Thanks
It seems to work fine on my X1.
But gps is not recognized on port 4 baud 4800...
Thank you to m4f1050 for pointing me in the right direction!
This is used to change the PPP user ID so that you can switch to another CDMA provider and use their data plans. Normally if you try to change the User ID to (ESN)@new.carrier.com, the phone will revert back to (ESN)@mdata.vmobl.com upon reboot. If you follow these directions, the settings should stick. This was created for the Optimus V but it will most likely work for other phone with the same issue.
Warning: Do not do this unless you understand the consequences. You will lose access to your VM data plan by doing this. You will need to change your User ID back if you want to use VM again.
Download QXDM and QPST.
Install both QPST and QXDM.
Follow the steps found here to get your MSL code and to configure QPST. You can stop at step 8 of "Update your PRL". As a last resort, if the previous method fails, you can get your MSL code by following this.
Download these rar'ed text files: Qualcomm.rar
Unrar them and place them inside C:\Users\Public\Documents\Qualcomm\QXDM\Vendor\Qualcomm\
Overwriting the original files. If they fail to overwrite the files, right click Diag.txt, select properties and uncheck "read only". Do the same for NVItem,txt.
Open QXDM Professional
If your phone isn't already recognized and connected, Go to Options > Communications and select the appropriate Target Port. This will be the port you configured in step 2.
Once connected, under view, select NV Browser.
Scroll all the way down to item 39939 and select it. The lower half of the window should show a list of values.
Hit read. Take note of the values in case you want to reverse what we are doing, and then turn them all to zero under "input". You edit them by double clicking them
Hit Write.
Next, without touching anything else, open QPST Service Programming.
Select Read, enter your MSL from step 2. An error will pop up, but ignore it.
Edit M.IP and PPP Config - AN entries to your desire.
Hit Write and Enjoy!
After you do this once, you can change your User ID by starting with step 12. You do not need QXDM any more.
doesn't seem to work for me. 39939 is empty
mmarz said:
This is used to change the PPP user ID so that you can switch to another CDMA provider and use their data plans.
Click to expand...
Click to collapse
I plan to use a regular Evdo dumb-phone (not an Android) as a donor. Is it even possible?
got it to change but still no internet on VM. I am converting sprint Optmimus s to virgin mobile .. but I haven't been able to get data to work. I am now able to change the MIP settings but the first profile always gets enable and the 3 disable. I can change the 1profile to anything now with tutorial, just not able to disable it.
prominator said:
got it to change
Click to expand...
Click to collapse
How did you solved the problem of 39939 being empty?
followed the instruction but on my winxp machine.
prominator said:
followed the instruction but on my winxp machine.
Click to expand...
Click to collapse
How come? Can you please explain?
you know how you have to put some files in C:\Users\Public\Documents\Qualcomm\QXDM\Vendor\Qua lcomm\??
well my windows 7 machine didnt have that directory. so I couldnt do it.
on my windows xp it had it.
help nv edit
mmarz said:
Thank you to m4f1050 for pointing me in the right direction!
This is used to change the PPP user ID so that you can switch to another CDMA provider and use their data plans. Normally if you try to change the User ID to (ESN)@new.carrier.com, the phone will revert back to (ESN)@mdata.vmobl.com upon reboot. If you follow these directions, the settings should stick. This was created for the Optimus V but it will most likely work for other phone with the same issue.
Warning: Do not do this unless you understand the consequences. You will lose access to your VM data plan by doing this. You will need to change your User ID back if you want to use VM again.
Download QXDM and QPST.
Install both QPST and QXDM.
Follow the steps found here to get your MSL code and to configure QPST. You can stop at step 8 of "Update your PRL". As a last resort, if the previous method fails, you can get your MSL code by following this.
Download these rar'ed text files: Qualcomm.rar
Unrar them and place them inside C:\Users\Public\Documents\Qualcomm\QXDM\Vendor\Qualcomm\
Overwriting the original files. If they fail to overwrite the files, right click Diag.txt, select properties and uncheck "read only". Do the same for NVItem,txt.
Open QXDM Professional
If your phone isn't already recognized and connected, Go to Options > Communications and select the appropriate Target Port. This will be the port you configured in step 2.
Once connected, under view, select NV Browser.
Scroll all the way down to item 39939 and select it. The lower half of the window should show a list of values.
Hit read. Take note of the values in case you want to reverse what we are doing, and then turn them all to zero under "input". You edit them by double clicking them
Hit Write.
Next, without touching anything else, open QPST Service Programming.
Select Read, enter your MSL from step 2. An error will pop up, but ignore it.
Edit M.IP and PPP Config - AN entries to your desire.
Hit Write and Enjoy!
After you do this once, you can change your User ID by starting with step 12. You do not need QXDM any more.
Click to expand...
Click to collapse
what's item 39939 called in NV Browser not all phones have item 33939 thanks for any help
Anybody still have these files? Qualcomm.rar mediafire link is dead. Thanks
bump
links dead please revive thread
bump again. mmarz has had no activity since 2011 on both here and androidcental. Someone with these files please chime in.
Anybody know how to add the 4g only setting
https://forum.xda-developers.com/me...te-4g-mode-t3828656/post77318151#post77318151
try this...
Unfortunately, it doesn't work for me. 4g only is not unlocked. Has anyone else's ideas
MasterLu2k said:
Unfortunately, it doesn't work for me. 4g only is not unlocked. Has anyone else's ideas
Click to expand...
Click to collapse
Hello,
yes, now we finally found a solution.
Do exactly as described:
Download Settings Database Editor from playstore and open it
Look for hw_networkmode_preference and edit the stock value "9,6,2,1" to "11"
Restart the device
Open Settings Database Editor
Click on + Add new setting at the top
Type "hw_add_4g_only" (without " ") and press save changes
Type in your country code, example "502" Malaysia or "262" Germany. Press save changes
Type "hw_add_4g_only" (without " ") and press save changes (YES, REPEAT STEP 6)
Type in your country code, example "502" Malaysia or "262" for Germany and press save changes (YES, REPEAT STEP 7)
Restart the device and VOILA!
Now you have access to ALL network modes. Select "LTE" or "4G" for 4G only functionality.
Like this, you have stable Internet nearly where ever you go, without dropping back to overcrowded 2G/3G Networks.
Best,
Stefan
p.s.: thanks to ronald_loulan for original solution!
will this work when travelling to other countries?
It's work
Thank you very much
Edit: got it working 4g only now.
One question though, the UK country code is 234 and 235.
Do I add both numbers and just separate them with a comma?
Thanks.
Mate 20 pro 4g only
Xergi said:
Hello,
yes, now we finally found a solution.
Do exactly as described:
Download Settings Database Editor from playstore and open it
Look for hw_networkmode_preference and edit the stock value "9,6,2,1" to "11"
Restart the device
Open Settings Database Editor
Click on + Add new setting at the top
Type "hw_add_4g_only" (without " ") and press save changes
Type in your country code, example "502" Malaysia or "262" Germany. Press save changes
Type "hw_add_4g_only" (without " ") and press save changes (YES, REPEAT STEP 6)
Type in your country code, example "502" Malaysia or "262" for Germany and press save changes (YES, REPEAT STEP 7)
Restart the device and VOILA!
Now you have access to ALL network modes. Select "LTE" or "4G" for 4G only functionality.
Like this, you have stable Internet nearly where ever you go, without dropping back to overcrowded 2G/3G Networks.
Best,
Stefan
p.s.: thanks to ronald_loulan for original solution!
Click to expand...
Click to collapse
Here is what work for me.
If you already had a hauwei phone and used "setedit" and you now upgraded to you Mate 20 pro with using the "phone clone" app.
You will notice the "setedit" app won't be copied over. So head on over to "play store" and download it.
Follow the steps give in this thread to enter all the setting on the "setedit" app.
Restart your device. You will see it didn't work. No problem. Just uninstall the "setedit" app and restart your device.
Now go to your mobile network setting and you will see you will have all the setting for networks including 4g only.
you can try this at teknokia site