I have been looking for an adaptor to plug my own headphones into that includes media controls (+the normal microphone, pickup/hangup etc). The one from HTC themselves HERE only includes a pickup/hangup button and mic.
I tried the headset from the wifes Nokia N86 which has media controls and a 3.5mm plug to use your own headphones. The controls didnt work so I cant just get one designed for a Nokia.
I have seen the guide on how to rewire the existing headset with your own earbuds but I am reluctant to go chopping up my headphones and headset.
Has anyone got one and where from?
Buy an extra pair of the stock headphones and chop them up. Instead of soldering on new ear buds, solder on a female adapter to plug your preferred headphones in.
http://www.expansys.com/d.aspx?i=188898
i too would like to know if anythings out on the market for this. there must be an easier way round this than having to chop and put back together different buds and cables......
hadn't thought about putting a female connector on a spare headset Might take a trip down Maplin at the weekend.Would be better if someone would make 1 though.
Related
Just a bit of whining here...
The TyTN seems fine after a month of use but the headset issue is blowing my mind. I want to listen to the music and talk on the phone with some quality headsets.
First the supplied headset is a non standard USB, you cannot use your own headphones or connect to speaker inputs. Bluetooth stereo headsets are available but I believe that they are still too bulky and the technology is not yet fully developed.
You can't charge the phone while using the headset. This is just dumb, Very dumb.
Needless to say the quality of the supplied headset is not good, it is not even recognized by the phone as headset when you connect it. If you connect it to your phone while the phone is non silent, the phone still rings and not just your headset.
I have no idea why HTC is doing this, the TyTN is a relatively large device and it doesnt make sense that there are no spaces for a 2.5mm plug where you can buy all kidns of aftermarket wired headsets for it. Even the high end headset makers SHURE make headsets with the 2.5mm...
Finally I've made a move. TyTN X Sony Crossover Custom Headphones.
I've used a solder to remove the original earbuds wire and soldered a pair of cut SONY MDR-EX71SL headphones on. They sound 100 times better than the stock ones. This will ease my frustrations for now. I was tempted to solder my MDR-EX90LP on but they are $100 a pair. Too much for now
Later on I will try to rework the stock mini USB headphone and make a 2.5mm connector for it so I can use all kinds of headphones(with mic) and connect to a speaker system as I want!
EDIT: It appears that the original mini USB headset has 6 wires, 4 should be for the headphones and the remaining 2 for the mic, I can simply cut up the wire right after the mini USB port and connect the 6 wires to a standard cell phone headset 2.5mm connector then I should be able to connect the TyTN to all kinds of headsets![/img]
Arent you essentially doin this? http://www.4winmobile.com/tutorial-replace-hermes-headset-connector-with-35mm-socket-vt3146.html as seen in another post, seems like the most universal way to solve the problem.
I do like the way you built a set without a plug, cleaner..less cord and weight, but I know myself, I go through a pair of headphones about every 2 months on my mp3 player, Id hate to have to redo the soldering everytime, I expect with the headphones being such an issue for most peple that the market will be flodded in a month or so with headphones for the tytn, or atleast adapters, shoot, the one guy in the above url even offered to do it for free, as long as you bought the plug.
is there still no adaptor available to buy?
i just do this way........
can swap any earpiece....
crash74 said:
i just do this way........
can swap any earpiece....
Click to expand...
Click to collapse
@crash74
Looks very good, even more solid than the other solution, but how do you open the unit to reach the print, is their any trick?!
Can i also use the new connection as a line-out for little active stereo boxes, or is this to tricky for TyTn/boxes?
worked like a dream i have no more crapy hissing inbetween tracks and now i can play my song thu my hi-fi that 1 to the modders and 0 to htc
Adapter usb to 3.5 jack
Go to semsons.com, they have the adapter
qing84, I have the same headphones as u=) firstly I solve this problem like you, but I smash the small "black box"=) with mic and volume control, and i was need connect my mdr-ex71 directly to TyTN without "black box"=(
I was glad that i did it, because sound became much more louder, and more clean...
qing84 said:
Just a bit of whining here...
The TyTN seems fine after a month of use but the headset issue is blowing my mind. I want to listen to the music and talk on the phone with some quality headsets.
First the supplied headset is a non standard USB, you cannot use your own headphones or connect to speaker inputs. Bluetooth stereo headsets are available but I believe that they are still too bulky and the technology is not yet fully developed.
You can't charge the phone while using the headset. This is just dumb, Very dumb.
Needless to say the quality of the supplied headset is not good, it is not even recognized by the phone as headset when you connect it. If you connect it to your phone while the phone is non silent, the phone still rings and not just your headset.
I have no idea why HTC is doing this, the TyTN is a relatively large device and it doesnt make sense that there are no spaces for a 2.5mm plug where you can buy all kidns of aftermarket wired headsets for it. Even the high end headset makers SHURE make headsets with the 2.5mm...
Click to expand...
Click to collapse
umm...you could have just bought this.... http://www.cellphoneshop.net/auadforci85.html
i think its a good idea to replace the head phone leaving the mic in workin condition.as there is no connector is still available at least in my town.i ll try it tomorrow.thanx dude
I'm looking for an adapter for my Cingular 8525 that allows me to plug in a plain ole 2.5mm headset that I've come to love.
I've seen plenty of adapters for sale that allows one to use normal stereo earplugs with the TyTN, such as on http://www.doml.net/productdec.asp?pid=2698&model=HTC_TyTN&modeln=TyTN
The pinout seems to be Pinout from Tracy and Matt's blog
Should I, perhaps, just bust open the crappy Cingular headset and do some soldering? Will the impedence for the microphone be the same? How should I combine the stereo that they have in the crappy headset to the mono that all 2.5mm jacks use?
Thanks!
-Humbert
workable, but not great
I used the same pinout to add a 3.5mm jack to the original headset end. The problem is the wires used in the cable are very difficult to solder. They are more like a metallized fabric than plain copper wire. And I am pretty good with fine wire soldering in general.
That said, I did get the jack on (though I'm not thrilled with the non-flowed solder joints) but the output level is pretty low. If I plug it into the input jack on my car stereo, the GSM phone noise (which I *hate*) overwhelms the wired signal every time I change towers.
Bill
Does anyone know if the HTC P3350 W100 Wired Remote Control
http://www.expansys.com/htc/p_htc_item.aspx?i=147564[/URL]
will work with the Cingular 8525 (Hermes, TyTN)? This is sold in Europe and can be had in the US from Mobile Planet which seems to be the same as expansys.com.
On the European HTC site there is also a media fix that may apply to this accessory as well as the Y connector.
HTC audio Drivers
Downloading and installing this driver update will provide your HTC mobile device with the latest available optimised software for use with the following accessories:
YC A120 Y-Cable adaptor
The hot music setup for Mogul and 8525
I just purchased the HTC RC W100 Remote from Mobile Planet. It connects to the phone's extUSB and provides a 3.5mm headset jack that carries the mic port out to the connector. It has a 36" cord so there is a lot of cord if you have a long headset cord.
The head has controls for fast forward, pause, +/- volume and you can answer/end calls, mute and put a call on/off hold. This assumes that you have a mic on your headset to talk into.
The http://www.Europe.HTC.Com site says it is for the TyTn II but it seems to work with both the 8525 and the Mogul . . . It is not on the USA site at all.
I use the Sure SE110s stereo headset (individual internal sub-woofer component) and added their MPA-C cable that has a mic in it (Thsi would work for any headset). I have not found any other solutions that wok this well.
The standard headset really has poor quality and is uncomfortable for my ears. Bluetooth is either a mono headset w/ mic or a stereo headset (no mic) and the battery life is unpredictable.
This way I can ride my bike and control my music while the Mogul stays in my camel-back and when a call comes I can actually answer it and then go back to listening.
Very cool setup.
So this doesn't solve the headphone problem? Can't I just buy this and a pair of headphones? I don't need handfree anyway
E: Why a 36'' cord? I totally lost interest
Headphone Problem
N1c0_ds said:
So this doesn't solve the headphone problem? Can't I just buy this and a pair of headphones? I don't need handfree anyway
E: Why a 36'' cord? I totally lost interest
Click to expand...
Click to collapse
N1cO;
I do not know what headset problem you are referring to but this is definitely a solution if you want to listen to music with a good stereo headset. I just happen to like the Shure stuff because they eliminate some road and wind noise while I am riding my bike or skiing. Also the higher end ones actually have miniature tweeters and sub-woofers built in.
All you need is the W100 and any headset with a 3.5mm jack.
As it turns out, I just found out the unit has a built-in mic and that eliminates the need for a more expensive headset that has a mic. There was nothing in the manual that came with it that talked about the mic! So RTFB does not work!
It also comes with a small disc that has the driver in it. I tried to install it on my Mogul but it said that I had the latest driver . . .
As far as the 36" cord, my Shure headset comes in 2 pieces, the earphones are on a short cord so it is not too long. If you had a standard headset, it might get a little long.
The other side of the Shure headset has the connectors that go into the device(s). This way you can have several different connectors for different phones, MP3 players, etc. Blackberry's and Razor's have different jacks and most cell phones like the HTC 8125 (Cingular) use a 2.5 mm jack.
Hello,
From the searches I have done on here and other forums to include cell phone stores, I can't seem to find any information pertaining to USB headphones. Basically my question is: Are there any reasonably priced headphones that directly plug into the usb port (without any adapters or mini jacks as the plug)?
Thanks.
HTC headphones
http://store.wmexperts.com/htc-stereo-headset/11A29A1450.htm
For 15 bucks you get something from HTC that's workable until you find what you really want. Decent music quality. No adaptor needed.
It is funny you post this. I was just searching for some today and I purchased these.
If you search OEM Heaphones Fuze on eBay, you can find some for $10 shipped.
i have a sprint TP and DL the fuse FM radio app and it says that the phone uses the headphones as an antenna. mine does not work, you think with the fuse headphone it would??
USB Headphones - Not all work?
Are there different types of mini-USB headphones?
I just purchased a pair of Motorola "Stereo Headset with Enhanced Mini USB Connector" headphones that do not work when plugged into my fuze.
However, I went and found the old headphones from my Dash and plugged it in and it works.
Both have the phone/music switch.
Why would one work and other not? The shape of the of the jack on the old set just a little different that the Motorola's which look like a fat little "t" and is the same shape as all the connector wires and charging wires I am using. The shape of the jack on the old ones, however, does match the shape of the fuze jack.
Sorry if this is an obvious questions, but what am I missing? What do I need to look for when purchasing earphone/headset?
I have answered my own question. HTC is using a proprietary form of USB...extUSB. It combines audio and data, so you can use regular mini-USB for everything except audio. This bugs me. why do you take something that is supposed to be "universal" then make it proprietary. So now I gotta look for and buy special headphones.
bluetooth headset
I personally use the bt3030 bluetooth headset from jabra. Full stereo use any regular headphones you like. I use the stock ear buds works fine. These work for phone calls sprint nav as well as full stereo from mp3's basically any audio can be funnelled into these. cost around 80 bucks.
arsmithsr said:
I personally use the bt3030 bluetooth headset from jabra. Full stereo use any regular headphones you like. I use the stock ear buds works fine. These work for phone calls sprint nav as well as full stereo from mp3's basically any audio can be funnelled into these. cost around 80 bucks.
Click to expand...
Click to collapse
You can get the 3030's from newegg for 40 shipped in bulk packaging. Work great and no need to plug them into the phone since they are bluetooth. Give you the ability to answer phone, have remote, and listen to music. I love them. Got some skull candy headphones for 10 bucks from marshalls to replace the stock headphones they came with. Check them out
Headphones
Anyone found any USB headphones that have equal cord length on both sides? I really hate the uneven setup..always seems to pull one or the other out...... Thanks !!
I posted a reply to this thread: http://forum.xda-developers.com/showthread.php?t=450197 because it also talks about such an adapter, but I thought I would post a new thread for the phone that I actually have.
I'm looking for a extUSB to 3.5mm adapter, but not the common kind that allows you to plug in stereo headphones or has a microphone built inside the adapter. I'm looking for an adapter that allows you to plug in stereo headsets with in-line microphones. These headsets are designed for iPhones and BlackBerrys and has a 3.5mm connector with an extra ring to support the microphone, and I'm hoping to find an extUSB adapter that supports 3.5mm connectors with three rings so the microphone would work. Does anyone know if such a thing exists? Thanks.
I use this one. It's kind of big but it is the only i can find that I am able to use my iphone headphones with inline mic. After cupcake came out the adapter stopped working but is now working with cyanogen's rom. I would love to find another smaller one that will work with an inline mic.
Thank you so much flowidc for confirming that such a thing actually exists! Please keep me up to date on your quest to find a smaller version of the adapter.
flowidc said:
I use this one. It's kind of big but it is the only i can find that I am able to use my iphone headphones with inline mic. After cupcake came out the adapter stopped working but is now working with cyanogen's rom. I would love to find another smaller one that will work with an inline mic.
Click to expand...
Click to collapse
is this adapter still working for you in Cyans 4.04? mine isnt being detected.
Figured it out. you need the ToggleHeaadset.apk
foltz61 said:
is this adapter still working for you in Cyans 4.04? mine isnt being detected.
Figured it out. you need the ToggleHeaadset.apk
Click to expand...
Click to collapse
mine never broke. only time it didn't work was in OTA cupcake
I have this same HTC usb to stereo with mic adapter and have used it with Cyan 4.04, Cyan 41x, and all the Hero Roms and had no problems. I use both Blackberry earpieces w/ mic and a cheapo earpiece w/ mic. I like way better than the regular HTC usb adapter and earbuds.
I found it on Ebay, I offered the guy $5 and he accepted my offer. Here is the link
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=330350650612&ssPageName=STRK:MEWAX:IT
this might be a stupid question, but would the HTC Multifunction Audio Adapter allow you to use a headset that comes with a mic, or would you have to use a earpiece along with an inline microphone?
thanks
shockaj said:
this might be a stupid question, but would the HTC Multifunction Audio Adapter allow you to use a headset that comes with a mic, or would you have to use a earpiece along with an inline microphone?
thanks
Click to expand...
Click to collapse
You just use a headset that has a built in mic.
*edit*
Nevermind, same thing already posted but for much less...
Try this instead
http://cgi.ebay.com/HTC-OEM-Stereo-Headphones-Headset-Adapter-GOOGLE-G1_W0QQitemZ220410822003QQcmdZViewItemQQptZPDA_Accessories?hash=item3351823d73&_trksid=p3286.c0.m14
Great adapter and good build quality too (it has rubbery coating on the cable and it doesn't feel/look cheap unlike some adapters with this style). Great for driving headset since it already has built-in mic. You can use any headphones you want, even though I think the original pair that comes with it performs quite well. The downside is that there's no manual volume control on it, but I can live with that.
Dream not of inline microphones...
I got the OEM adapter as well, but on my ADP1, it doesn't fully work;
I can charge, but the 3.5 and 2.5 jacks are dead. They neither work as outputs or inputs. If I plug an EXtUSB to 3.5 adapter into the EXTUSB headset port on the OEM adapter, the phone's microphone is disabled.
I really want an adapter that can be used to connect, via 3.5 wire, to the car stereo, and still be able to use the phone's microphone, or be able to plug in an external microphone for hands-free use.
Troglodad said:
I got the OEM adapter as well, but on my ADP1, it doesn't fully work;
I can charge, but the 3.5 and 2.5 jacks are dead. They neither work as outputs or inputs. If I plug an EXtUSB to 3.5 adapter into the EXTUSB headset port on the OEM adapter, the phone's microphone is disabled.
I really want an adapter that can be used to connect, via 3.5 wire, to the car stereo, and still be able to use the phone's microphone, or be able to plug in an external microphone for hands-free use.
Click to expand...
Click to collapse
I have a similar setup, I discovered yesterday on the way home a way to get audio through the 3.5mm jack. This is a convoluted way, but it did work.
1. I had my OEM adapter plugged in
2. I plugged in my OEM headset to the headset jack
3. I plugged in the 3.5mm adapter into the 3.5mm jack
4. Started the music player
The sound came through both the headset and the car radio, unplugged the headset and the sound continued to play through the radio. Once the 3.5mm jack is unplugged, the process will need to be repeated. I hope this helps.
rrstx