The problem I have is that my HD2 used to last for about 48hrs, but after playing around with it as we do with roms! the battery life suddenly drained in hours.
Battery used to last about 48 hrs with a charge time of less than 2 hrs. It then started to last 8hrs with a 4hr charge time, now it lasts 6hrs.
This is with all apps turned off no data connection, only sending txt and quick calls during the day. 100% power at night and it will be dead by the morning!
I have removed all programs and gone back to UK t mobile 1.72 rom, with same results.
I phoned T mobile and they have been kind enough to send me another free battery to solve the problem but to no avail!!!!
I am now going to send it back to get repaired, however HSPL is installed and it is being a proper pain to remove. I have done searches and watched the utube clips, so please dont say use search, as I have done for 2 days now!!
My HD2 will not enter bootloader by the buttons, I HAVE to use the bootloader cab file and install it and do it that way. Next problem is when it asks me to press the power button to start update image, it does not respond to the power button or the down button to cancel! (have to pull battery of to restart)
I have tried lots of renamed ruu_signed files (uk t mobile and htc) on a FAT32 formatted SD card, same problem.
details are as follows
OS version 5.2.21889 (21889.5.0.87)
Manila version 2.5.20121429.0
ROM version 1.72.110.4 (86525) WWE
ROM date 04/02/10
Radio version 2.07.51.22_2
Protocol version 15.32.50.07U
Really need to get rid of HSPL so it can get repaired!!
Any ideas to this strange problem? Anyone experienced this aswell?
Thanks in Advance
AJ
run hspl2 and choose 1.66.0000
hspl gone.
Thanks for the quick reply!
I downloaded and tried to install HSPL2 from the search results.
I follow the on screen instructions, as it waits for a USB connection I get an critical error box appear on the laptop.
Flow: 00000001
Error code: 00000002
Description: USB Connect failed!
Freezes on the bootloader screen.
I have tried all 3 USB ports on the laptop and another USB cable to no joy!
Has my phone got gremlins crawling inside it or what!
Any help to save my sanity will be greatly appreciated!
Thanks
AJ
normally i would say enter bootloader manually then run hspl but you cant, so, let it fail, then exit hspl, leave teh phone in bootloader, and run it again. You can try over and over, different ports, whatever, no need to re start the phone each time, just leave it in bootloader and connect the usb cable.
As always, the following applies,
1 - right click hspl.exe and choose run as administrator
2 - dont use front mounted usb ports, or ports through hubs, DO use a port around back of the pc (i.e one connected to teh motherboard) EDIT - oh its a laptop, could be problematic, find a friend with a real computer.
Just cos a port works for active sync doesnt mean it will work for hspl, so keep trying ports.
If all else fails use a different pc.
Cancel last, it just worked!!!
Thanks very much for your help.
One question though, now that the spl is 1.66 and the original was 1.42, can they tell that the phone has been tampered with?
aussiejock said:
Cancel last, it just worked!!!
Thanks very much for your help.
One question though, now that the spl is 1.66 and the original was 1.42, can they tell that the phone has been tampered with?
Click to expand...
Click to collapse
you said you upgraded teh rom to 1.72, , well if you hadnt had hspl installed it would have upgraded the spl to 1.66.0000, which is why i said go for that one.
Thanks Samsamuel,
Everything is back to normal. I put it in for warranty repair yesterday, need to wait 2-3 weeks now!
again thanks for your help.
AJ
hehe, start marking off the days on ya calendar.
Related
My xda 2 is stuck on the bootloader and wont do anything after trying to reset it ive tried i think everything that i can possible do and i read most of what was offered yet its still stuck on the bootloader. I tried to upgrade from v1.60.... to the latest at v1.72.187 uk o2 . Please help ><
Have you tried resetting your device, placing it back in the cradle and re-running the upgrade?
I have tried reseting but it fades then reappears disallowing me to run the upgrade 'Xda_II_172187_Final' but i have downloaded another which sizes around 512kb but this says that the rom image is not present. :/ can u link me to another upgrade if it may help
Shadow786 said:
I have tried reseting but it fades then reappears disallowing me to run the upgrade 'Xda_II_172187_Final' but i have downloaded another which sizes around 512kb but this says that the rom image is not present. :/ can u link me to another upgrade if it may help
Click to expand...
Click to collapse
Exactly which upgrades have you attempted? What happens when you run the XDA_II_172187_Final upgrade?
What is the 512kb upgrade you mention?
I used 'himaupgradeut_197.exe' after the 'Xda_II_172187_Final'.
'himaupgradeut_197.exe' was the 500kb file which gave me the error
that no rom image was found and the 'Xda_II_172187_Final' was the only 1 that i used to upgrade and that says it cannot connect to the device ...make sure its connected.
Shadow786 said:
I used 'himaupgradeut_197.exe' after the 'Xda_II_172187_Final'.
'himaupgradeut_197.exe' was the 500kb file which gave me the error
that no rom image was found and the 'Xda_II_172187_Final' was the only 1 that i used to upgrade and that says it cannot connect to the device ...make sure its connected.
Click to expand...
Click to collapse
The HimaUpgradeUt_197.exe file is not an upgrade it is a version of the upgrade program. It still needs to be used with all the other files that form part of the upgrade process.
As regards the connection error, make sure you are in bootloader mode (by pressing Jog button and Power button at the same time as pressing reset) before retrying the upgrade. Also make sure the USB cradle is plugged directly into a USB port on your PC and not through a hub and that the power supply is connected to the cradle. It may help to make sure that ActiveSync isn't running also, as it is not required for upgrading.
Isnt it already in bootload mode? if not i dont know where the jog button is Also i just realised i didnt have my cradle its own powersuplly which i have done just now but i dont want to carry on witht upgrade is there a way i can just make it back to normal ?
Shadow786 said:
Isnt it already in bootload mode? if not i dont know where the jog button is Also i just realised i didnt have my cradle its own powersuplly which i have done just now but i dont want to carry on witht upgrade is there a way i can just make it back to normal ?
Click to expand...
Click to collapse
It sounds like your device is already in bootloader mode - my suggestion is just a 'failsafe' The Jog button is the multi-directional button at the bottom centre of your device.
I don't think it is possible to 'go back' to normal as if you never did anything. With the power connected properly there is every chance an upgrade will now work. You can, of course upgrade using the original ROM version, if you know what that was.
hmm its still done a restart and yet it doesent seem to connect. When i restart the xda 2 its still in bootload mode when i place it in cradle still in bootload mode and i still get the same errors witht the upgrade ><
OK. This should work Can you try a different USB port? Failing that, is it possible to try another PC? I know about other users that had connection problems and tried a different PC and it worked OK.
Omg thank you i thought i lost it Thank you Very much i cnt thank you enough. ^^
For reference i switched the USB cable around and it worked ^^
That is great news
I think my Mogul is bricked after trying the ROM update; after about 7% update Vista kicked off the USB connection and I'm left with a tri-color screen. When I try to reinstall the ROM I get an Error 328 message - Invalid Command. Any help? Thanks!
Definitely not bricked if you can get to the tricolor screen.. which rom exactly were you flashing and what have you flashed so far (unlocker, etc)?
Have you tried updating from the microsd card? That solved a similar problem for me.
AFH said:
I think my Mogul is bricked after trying the ROM update; after about 7% update Vista kicked off the USB connection and I'm left with a tri-color screen. When I try to reinstall the ROM I get an Error 328 message - Invalid Command. Any help? Thanks!
Click to expand...
Click to collapse
What steps have you taken so far? That might help others figure out your problem(I would help but I'm leaving my computer right now)
Just tried to re-cradle and reinstall the update - ROM 3.35.651.2 from HTC's website, and I get the message Invalid Command and it stops the update. Can I run this from the MicroSD card as suggested? Any help very much appreciated!
I have no access to anything on the phone BTW - just the screen and nothing else. The screen has four horizontal stripes - Red, Green, Blue and White. In the red stripe it says TITA100 MFG, SPL-2.03.1000, CPLD-9, and at the top of the screen RUUNBH....
Run Olipros 2.40 bootloader. Than, go back and flash the 3.35. I'm pretty sure you need the 2.40 to load the new ROMs. Yes, just run Olipro's 2.40 while you are in the tri-color screen. Also, make sure you have more than 50% battery life left.
Where do I get the bootloader and how do I run it? Sorry to sound dense, but this is new to me. I have the concept of running the bootload mode - Camera, Power, Reset, so I assume some software needs to be loaded on the MicroSD card? Thanks!
You know, it's fine if you're new to this....everyone starts somewhere...and it's good to see new faces in the community...
But what I don't get is why people insist on just flashing right away without reading and researching. Then they make posts about thinking their phone is bricked, not even knowing what a bootloader is.
My advice before you do anything else is to take an hour and read. Read about how to flash, read about bootloaders, read everything you can find about updating your phone. Then, try and fix your bootloader.
Your phone isn't bricked. A brick is just that, a brick. NOTHING works, not the bootloader, not the buttons, nothing.
gcincotta said:
You know, it's fine if you're new to this....everyone starts somewhere...and it's good to see new faces in the community...
But what I don't get is why people insist on just flashing right away without reading and researching. Then they make posts about thinking their phone is bricked, not even knowing what a bootloader is.
My advice before you do anything else is to take an hour and read. Read about how to flash, read about bootloaders, read everything you can find about updating your phone. Then, try and fix your bootloader.
Your phone isn't bricked. A brick is just that, a brick. NOTHING works, not the bootloader, not the buttons, nothing.
Click to expand...
Click to collapse
i second this emotion
Actually, although I'm new to this forum I'm not new to computers. I'm not as familiar with the inner workings of a handheld. I assume a bootloader is the software necessary to run the ROM flash from the SD card; when I run in bootloader mode, I do get a very brief "image not found", so I assume it's looking for the ROM image on the card. And I'm tracking down Olipros stuff right now through the forums, as well as the recommended reading. With a little written direction I think I can "unbrick" this phone. I did successfully flash another Mogul from a different computer, so assumed it would be as smooth; guess not. For those with the expertise, I certainly appreciate the advice and patience to teach a novice...
Once you find the required bootloader program, just run it as if you are flashing a ROM. Once you get "Olipro 2.40" on your tri-color screen, you'll know that your getting somewhere. But yes search and search and read. I also downloaded everything I think I would need also, just in case.
OK - so far 've tried running the Olipro Bootloader 2.40, but I get "device not connected." Perhaps I should mention I'm running Vista Home Premium, so no ActiveSynch; my PC has Mobile Device Center. I hear the little chime when I connect the Mogul, but the Olipro software doesn't recognize a connection....
I have done all of my flashes on my Vista Home Premium laptop. Make sure you uncheck "allow USB connection" on WMDC. Also, after every failed attempt, take the battery out of your phone for 3 seconds and then reinstall.
Did you mean check "allow USB connections"? WMDC is attempting to connect, but always fails. I was assuming because it doesn't recognize the PDA...
no he meant uncheck....READ!!
start here http://forum.ppcgeeks.com/showthread.php?t=9927
Thanks; I have an XP machine I'll try; jacking with the WMDC drivers in Vista would take more time than its worth...
Actually Vista should automatically find and install the required drivers for you. It shouldn't take long. It's well worth the time considering what you are getting yourself into.
First, thanks for the assistance all. Status to date: I have connected to my XP machine and still can't connect the Mogul to ActiveSynch. ActiveSynch won't recognize the device in its current state. I've tried running the bootloader program both with the "USB Connection" option in ActiveSynch on and off; when I run the bootloader I get a popup window that says "No device connected", and a query "Would you like to try copying again?" with button options "Yes", "No" or "Cancel." Clicking "Yes" gives me the same popup. Clicking "No" lets the loader proceed, but has no effect on the Mogul except ultimately it brings up a screen showing the percentage complete which remains at 0, and on the PC it brings up the Recovery screens for the ROM update, which have no effect on the Mogul because I assume no connection has been made. I'm obviously misinterpreting some of the steps?
Any way to run the loader from the MicroSD card? I think someone mentioned it before?
Sounds like you still didnt get Olipro 2.40 into your machine, right?
When you boot it (press camera+power+soft reset) which bootloader do you get showing?
If its 1.06 or something like that you need to flash a (manufacturer) stock rom.
If its 1.20 Olipro then you need to flash a customized pre-3.16 rom. (if you need one pm me and I will give you a link to a clean one for your carrier)
Either way you need to get the rom file called xxxx.nbh. Rename it to TITAIMG.nbh. Place that file into the root of a FAT32 formatted sd card. Inster it into your sd card slot and power down and power up the titan. It will automagically read the rom from the card and flash it for you. Same goes for radio nbh files
Hi, Let me honestly admit that I am a newby and have read the threads over the last few weeks so much that I'm really confused now. I read one thing which then asks you to click and read another, but the answers I want are only partly found.
So I hope someone can please take pity on me and answer the following:
I have a TyTN SIM FREE phone which has a Orange sim card. In fact, Virgin & o2 cards have been used on it but Orange seems the best at the mo'.
Does that mean its unlocked?
I am trying to upgrade to WM6 (without even thinking about WM6.1), but "Error 260" comes up each and every time. I have tried 150+ and its still the same.
Please believe me that I have tried every way mentioned on these forums. I've tried on a xp (I have Vista) and its still the same.
My phone screen just goes black when trying to install, then the error comes up.
What exactly is "OPEN PORT" ? I cannot find a thread that actually EXPLAINS that. What do I have to do when it says:"Reset your computer"? Which one, the desktop or the TyTN? If the latter, I have reset so many times. If the desktop, what do I have to reset?
My TyTN tells me that its a HERM 200 IPL- 1.00 and HERM 200-2.03.
If someone can just list in a order what I have to do in order to get this upgrade I would be for ever grateful. HTC do not want to know & London HTC Support Hotline was a washout.
I do hope to hear soon, cos' its started to drive me mad now.
reset both, try unplugging usb cable and plugging into another usb port if prob persists...
1). download and install Hard SPL ver 7. Here http://forum.xda-developers.com/showthread.php?t=296722
This makes it easier or possible to unbrick your phone if something does(will) go wrong. THIS IS A MUST!!!!!!!
2). Once you have Hard SPL on your phone, you can either use the pc to flash OR the sd card method. I personally prefer the sd method as its harder to brick your phone. To do this, download the HERMES rom of your choice. Unzip(rar) the file and generally there are 2 files. RUU_Wrapper.exe & RUU_signed.nbh. Copy the RUU_signed.nbh onto a fat 32 formatted memory card and rename it to "HERMIMG.NBH". Put it back in the hermes and go to bootloader( hold power and OK button(above the flywheel) and then reset with the stylus. hold ALL the buttons down until it goes into tricolour screen. It should automatically detect the flash file and start the upgrade process, follow the prompts... Please remember to either delete or change the name of the .nbh file else it will upgrade next time you go into bootloader.
Hope this helps... Cheers...
Hi. Thank you for your reply and at the mo' I'm trying to get the Hard SPL7 file on my pocket pc. I've never come across something which sounds easy but being very difficult! The file is on my phone, but "will not unzip 'cos .net compact framework is not on my pocket pc" when I am staring at it in the face in my downloads.
What I've decided to do is to do a hard reset and start afresh. I'll let you know how I get on....
download it to your computer, not the phone
pls see the guides here: www.mrvanx.org
Sorry not been able to try anything yet due to illness. Going to try tomorrow & I hope it works. Not tried for a while and already dreading it.
I'll let you know how I get on. Thanks for your replies.
Hi everyone. Just letting you know a friend of mine upgraded my pocket pc. He said it was "hard work" but he did it!
The phone works great and is much faster, but now I have another problem. It will not sync with WMDC.
It is possible a new thread will be following soon. I am at present, following other people's advice.
Thanks for everyone's help.
beegeebopper said:
Hi everyone. Just letting you know a friend of mine upgraded my pocket pc. He said it was "hard work" but he did it!
The phone works great and is much faster, but now I have another problem. It will not sync with WMDC.
It is possible a new thread will be following soon. I am at present, following other people's advice.
Thanks for everyone's help.
Click to expand...
Click to collapse
Letting us know what ROM you had flashed with would help. As the different ROMs have different solutions in solving that WMDC problem.
I got a friends hd2 several days ago and it was stuck on the White splash screen and wouldn't go further.
I tried Hard reset with keys and it didn't helped to get past that screen.
So i decided to flash a new ROM.
First I installed 1.42.HSPL on it to make myself safe and tried to install WWE version but failed at 9 %.
After this i tried near all the steps from another thread on the forum, the one of italian guy who tried almost everything.
Strange thing is that after trying several roms and failing all the times at 9 %, the phone once booted into windows, and i got this information from it:
Radio 2.05.51.05_2
G 15.28.50.07U
Rom 1.48.406.1 (71294) FRE
But after powering it off it didn't boot up another time.
Also there was a small damage on one of the battery pins but I think i managed to get it soldered from outside with soldering iron.
I also tried with MTTY and it didn't work either.
I got the official rom 1.48.406.1 FRE (because this phone is from swiss operator in french language) but it doesn't flash it goes to 9 % and gives error 290.
Ok, i started the thread because I actually wante to ask the question, why i'm unable to get into the Flash process from SD Card.
I formatted SD and copied the LEOIMG.nbh from official ROM and other ROM's too but when i press Reset and hold volume Down key sometimes nothing happens screen is black, sometimes im going into Bootloader with Serial shown and this text:
"Upgrade ROM code error. Please try again" and in the top right corner its written RUUNBH.
Anyone has any idea what could be problem of this device?
Btw I own LEO too and i never faced any problem till now, it was originally in German Language and i flashed it to WWE and didn't get any problems like this one.
gjizaqin said:
I got a friends hd2 several days ago and it was stuck on the White splash screen and wouldn't go further.
I tried Hard reset with keys and it didn't helped to get past that screen.
So i decided to flash a new ROM.
First I installed 1.42.HSPL on it to make myself safe and tried to install WWE version but failed at 9 %.
After this i tried near all the steps from another thread on the forum, the one of italian guy who tried almost everything.
Strange thing is that after trying several roms and failing all the times at 9 %, the phone once booted into windows, and i got this information from it:
Radio 2.05.51.05_2
G 15.28.50.07U
Rom 1.48.406.1 (71294) FRE
But after powering it off it didn't boot up another time.
Also there was a small damage on one of the battery pins but I think i managed to get it soldered from outside with soldering iron.
I also tried with MTTY and it didn't work either.
I got the official rom 1.48.406.1 FRE (because this phone is from swiss operator in french language) but it doesn't flash it goes to 9 % and gives error 290.
Ok, i started the thread because I actually wante to ask the question, why i'm unable to get into the Flash process from SD Card.
I formatted SD and copied the LEOIMG.nbh from official ROM and other ROM's too but when i press Reset and hold volume Down key sometimes nothing happens screen is black, sometimes im going into Bootloader with Serial shown and this text:
"Upgrade ROM code error. Please try again" and in the top right corner its written RUUNBH.
Anyone has any idea what could be problem of this device?
Btw I own LEO too and i never faced any problem till now, it was originally in German Language and i flashed it to WWE and didn't get any problems like this one.
Click to expand...
Click to collapse
Not sure if this is the problem, but what size is your SD card? I've heard, that sometimes is impossible to flash from larger cards, safest way is to use cards up to 2GB...
CaponiND said:
Not sure if this is the problem, but what size is your SD card? I've heard, that sometimes is impossible to flash from larger cards, safest way is to use cards up to 2GB...
Click to expand...
Click to collapse
Actually the sd is original 2gb that comes with hd2.
Friend, try to flash hspl 2.08 !!
Most likely that is the problem.
Enter the bootloader and connect it via usb to your usb and install 2.08 hspl (search fo it on xda developer forum)
Before instaling it read the instruction so that you know that hspl 2.08 can be installed over the old version of hspl that you installed!!
Oh and update radio to atleast 2.07
2.14 is very good
PS
Did you perform task29 before flashing?
mladen.p said:
Friend, try to flash hspl 2.08 !!
Most likely that is the problem.
Enter the bootloader and connect it via usb to your usb and install 2.08 hspl (search fo it on xda developer forum)
Before instaling it read the instruction so that you know that hspl 2.08 can be installed over the old version of hspl that you installed!!
Oh and update radio to atleast 2.07
2.14 is very good
PS
Did you perform task29 before flashing?
Click to expand...
Click to collapse
I guess I should try to install 2.08 HSPL, do you think i can use the same HSPL installer and just install 2.08 hspl from it? Because i already tried 1.66.HSPL but didn't worked.
And yes i performed task29 two or three times it finishes with some known output message which is stated on the original MTTY thread to be ignored.
Any other ideas?
gjizaqin said:
I guess I should try to install 2.08 HSPL, do you think i can use the same HSPL installer and just install 2.08 hspl from it? Because i already tried 1.66.HSPL but didn't worked.
And yes i performed task29 two or three times it finishes with some known output message which is stated on the original MTTY thread to be ignored.
Any other ideas?
Click to expand...
Click to collapse
you have to flash the HSPL back to 1.42 0000 ,then update the HSPL to 2.08 HSPL directly. if you flash it from 1.66. it can not work..pls be noted. good luck to you .hope you leo can be used again.
zengxisheng said:
you have to flash the HSPL back to 1.42 0000 ,then update the HSPL to 2.08 HSPL directly. if you flash it from 1.66. it can not work..pls be noted. good luck to you .hope you leo can be used again.
Click to expand...
Click to collapse
Ok I installed 2.08.HSPL from 1.42.HSPL and it went successfully, now i see 2.08.HSPL on bootloader but it still fails to update ROM. Stops at 8 % on the phone with rectangle mark, and on the pc it stops at 9 %.
I get Error 290 - Unknown Command
But why i cant go into sd card flash screen when i press reset and volume down ?
I just used another 2 gb microSD and added LEOIMG.nbh from official FRE ROM and it doesnt work.
Hey bud,
I was having the same problem: the flashing didn't want to start by doing a reset+vol.down. I somehow got around this by putting the leoimg.nbh on my mircoSD card, and then started the flashing from my computer by running the .exe that contains the RUU (for ActiveSync flashing). This "magically" triggered the flashing from the mircoSD card (it showed me a screen whether i wanted to update leoimg.nbh). On this screen, pressing vol.down would start the flashing through ActiveSync, and pressing the power button would start the flashing from leoimg.nbh from your microSD card. In the last case, the update on your computer will stall at 0%, this is just because you're not running the update from your computer, but from your phone. On your computer it will time-out, but the update on your phone will continue!
I hope this works! But you're doing this on your own responsibility ;p
ce3c said:
Hey bud,
I was having the same problem: the flashing didn't want to start by doing a reset+vol.down. I somehow got around this by putting the leoimg.nbh on my mircoSD card, and then started the flashing from my computer by running the .exe that contains the RUU (for ActiveSync flashing). This "magically" triggered the flashing from the mircoSD card (it showed me a screen whether i wanted to update leoimg.nbh). On this screen, pressing vol.down would start the flashing through ActiveSync, and pressing the power button would start the flashing from leoimg.nbh from your microSD card. In the last case, the update on your computer will stall at 0%, this is just because you're not running the update from your computer, but from your phone. On your computer it will time-out, but the update on your phone will continue!
I hope this works! But you're doing this on your own responsibility ;p
Click to expand...
Click to collapse
Hmmm this kinda messed me up.
What EXE file you run on the pc so it triggered update from SD ?
Because it's upossible to connect with activesync and browse to sd without the phone being fully operational (winmo running).
So i would say maby you just got it somehow with key kombination, because it would be impossible to run it the way you say. Or maby i'm wrong.
Could you be more specific about how you exactly run that process?
Thanks for your kind help. Gjizaqin
Well, whatever ROM you want to flash,
when you download this ROM, the .nbh file is packed in a .exe file.
You transfer the .nbh file to your microSD (rename to leoimg.nbh), and you can run the .exe file to flash through ActiveSync.
Because it's upossible to connect with activesync and browse to sd without the phone being fully operational (winmo running).
Click to expand...
Click to collapse
For me it was possible: reset your phone with the volume button down, to get to the tri-color screen. It shows "serial" on it. When you then connect your phone using your USB cable, it should switch to "USB", after which you can run the ActiveSync flashing.
ce3c said:
Well, whatever ROM you want to flash,
when you download this ROM, the .nbh file is packed in a .exe file.
You transfer the .nbh file to your microSD (rename to leoimg.nbh), and you can run the .exe file to flash through ActiveSync.
For me it was possible: reset your phone with the volume button down, to get to the tri-color screen. It shows "serial" on it. When you then connect your phone using your USB cable, it should switch to "USB", after which you can run the ActiveSync flashing.
Click to expand...
Click to collapse
Whell, by doing this procedure your doing normal ROM Update, and it's not doing update from sd card.
Anyways i tried this way too but not successful, its stuck on 8 % and stay's that way for about 3 minutes, than it gives me error 362 on the loader.
Anyways thanks for your help mate.
Anyone with experience can give me advice what to do with this phone?
Thanks in advance.
Gjizaqin
i'm doing task29 too... but it hang when it runs on black screen showing the percentage bar. advise is appreciated. Thanks.
whizzkid_cool said:
i'm doing task29 too... but it hang when it runs on black screen showing the percentage bar. advise is appreciated. Thanks.
Click to expand...
Click to collapse
I guess were on the same boat
gjizaqin said:
I guess were on the same boat
Click to expand...
Click to collapse
I have the same problem, tried all sorts with no luck. Can't get SD card install to work either.
Oh this sounds fun, I can no longer run active syn with my leo, the computer reports that my "usb device is not functioning properly"
I have re downloaded sync, try as I might I cant it back up and running, I wish everyone else the best of luck
This might be just a little bit off topic, but does anybody know how it is possible that some SD cards are good for flashing ROM's and other (mostly the larger) aren't?
Do you also need to copy the folder "program files" from the SD card you've flashed the ROM with to the other SD card, when you'd like to use this for your device?
jordy1990 said:
This might be just a little bit off topic, but does anybody know how it is possible that some SD cards are good for flashing ROM's and other (mostly the larger) aren't?
Do you also need to copy the folder "program files" from the SD card you've flashed the ROM with to the other SD card, when you'd like to use this for your device?
Click to expand...
Click to collapse
There has been reported problems with some 16GBmSD cards when it comes to flashing from them.
The only thing you need on the mSD card is the LEOIMG.nbh file.
dwntoearth said:
Oh this sounds fun, I can no longer run active syn with my leo, the computer reports that my "usb device is not functioning properly"
I have re downloaded sync, try as I might I cant it back up and running, I wish everyone else the best of luck
Click to expand...
Click to collapse
If you boot up your phone to Bootloader mode (but not connected to the computer), the bottom of the screen reads 'Serial'. If you now plug it into the computer, does it change to 'USB'?
Your computer error message is just saying that the computer cannot install a driver to communicate properly with your phone. Since your phone isn't fully loaded into WinMo then your computer isn't going to recognise it as a WinMo device. So don't worry about that message.
feridoun said:
I have the same problem, tried all sorts with no luck. Can't get SD card install to work either.
Click to expand...
Click to collapse
I guess this problem happen to some of the flash addicts! Problem still unsolved...
Hi guys,
my htc hd2 is giving a white screen at the startup since today,
when I press volume down and start it shows this:
PB81100 HX-BC
SPL-3.3.0000 XE
I can connect it through usb to the pc,
when trying to run hspl4 it gives me
critical error
flow 00000001
Error code 000000002
Description: USB Connect Failed.
any idea how to make it work again>
Thanks!
Are you sure it does not say SPL 3.03.0000 lol just picking I know it does as there is no SPL 3.3.0000. Any way sounds like you may need to update your drivers. You can either go to control panel and device manager and find your phone click on it to make the device drop down then right click on the dropped down device and select update drivers and then select from the internet, or go and download the latest ActiveSynce or WMDC versions as the have the updated drivers.
If this does not work try changing USB ports, changing USB cables, or even change computers. Also are you right clicking on the HSPL.exe and selecting run as administrator?
I followed all your steps, updated everything, and used hspl4 as admin
now I have this
Critical error
flow 00000006
error code: 00000014
description: unknown
any ideas
rpedro82 said:
I followed all your steps, updated everything, and used hspl4 as admin
now I have this
Critical error
flow 00000006
error code: 00000014
description: unknown
any ideas
Click to expand...
Click to collapse
Are you flashing using ActiveSynce or are manually putting your HD2 into bootloader and then flashing?
Try hspl2 (or 3 for tmous), I've seen once or twice where hspl4 fails for no known reason. (And vice versa,,, sometimes hspl4 works where hspl2/3 doesn't)
T-Macgnolia said:
Are you flashing using ActiveSynce or are manually putting your HD2 into bootloader and then flashing?
Click to expand...
Click to collapse
doing it manually
samsamuel said:
Try hspl2 (or 3 for tmous), I've seen once or twice where hspl4 fails for no known reason. (And vice versa,,, sometimes hspl4 works where hspl2/3 doesn't)
Click to expand...
Click to collapse
doesnt work with version 3 or 2 since my firmware is 3.03 he gives an error saying he doesnt find the firrmware
rpedro82 said:
doesnt work with version 3 or 2 since my firmware is 3.03 he gives an error saying he doesnt find the firrmware
Click to expand...
Click to collapse
This is a long shot here but run a Task 29 and then while you do not have a ROM on the HD2 try to run the HSPL.exe as administrator agian. Be warned that any info that is not backed up or save will be lost when you run the Task 29, so if you do not want to do it I understand.
T-Macgnolia said:
This is a long shot here but run a Task 29 and then while you do not have a ROM on the HD2 try to run the HSPL.exe as administrator agian. Be warned that any info that is not backed up or save will be lost when you run the Task 29, so if you do not want to do it I understand.
Click to expand...
Click to collapse
trying this one!
can also try downgrading the spl by flashing a correct but lower version stock rom, which would then allow you to try hspl2.
Of course, the quickest easiest (and often very successfull) thing to try would be a different PC. there are dozens of threads where people try everything for hours, no luck, but 2 minutes on a different machine and hspl is installed.
rpedro82 said:
trying this one!
Click to expand...
Click to collapse
first time it did around 14% then gave an error message saying it was corrupt,
then second, third, fotrth time it stays at 0% and says recovery failed.
rpedro82 said:
first time it did around 14% then gave an error message saying it was corrupt,
then second, third, fotrth time it stays at 0% and says recovery failed.
Click to expand...
Click to collapse
There is something that is not right here and I can not put my finger on it.
There is something not right hear but I can not put my finger on it. I got another digestion, but aftercthis one I think I am going to be tapped out. Take and run the HSPL 4 again but instead of flashing HSPL flash SPL 2.08.0000 and see if it will let you do that. If it will the you should be able to flash. SPL to it then.
T-Macgnolia said:
There is something that is not right here and I can not put my finger on it.
There is something not right hear but I can not put my finger on it. I got another digestion, but aftercthis one I think I am going to be tapped out. Take and run the HSPL 4 again but instead of flashing HSPL flash SPL 2.08.0000 and see if it will let you do that. If it will the you should be able to flash. SPL to it then.
Click to expand...
Click to collapse
tried it still error :
Critical error
flow 00000006
error code: 00000014
description: unknown
now with Task29 I get error 270 when trying to do it.
Tried on two different pcs, one vista, one xp same thing.
if someone has another idea it would be great!
rpedro82 said:
if someone has another idea it would be great!
Click to expand...
Click to collapse
Hey rpedro82, I have one more suggestion for you. Now if you don't want to try thisI totally understand as I would be a little leiry about doing it myself. Some of the other members here on XDA that have had the same issue as you of not being able to get past the splash screen and not able to flash anything. This is what they did, they toke and placed their HD2 in a sealed plastic bag and set it in the freezer for 10 to 20 minutes then as soon as they took it out they flashed their HD2. I think this helps for two reasons, one if you are having overheating issues it will of course help with that temperarily. Two cold makes things contract so if you are having a issue with the processor and the main board loading connection for whatever reason the cold allows them to restablish the connection at least temporarily.
put it in the freezer, then retried, still stays at 0%
aaarg, its so frustrating,
any more ideas someone?
samsamuel said:
can also try downgrading the spl by flashing a correct but lower version stock rom, which would then allow you to try hspl2.
Of course, the quickest easiest (and often very successfull) thing to try would be a different PC. there are dozens of threads where people try everything for hours, no luck, but 2 minutes on a different machine and hspl is installed.
Click to expand...
Click to collapse
Have you tried Samsamuels above quoted suggestion you might have luck with one of these suggestions.
Hello guys...
I really need help with this HSPL...And some expert advice too..
I have problem with my EU HTC HD2 with HSPL...
I try to put 1.42.HSPL with HSPL2_run so i can put beck stock rom but after that all thing is stuck...
My bootloader screen look like this
SYSTEM DON'T ALLOW ME TO PUT SOME LINKS..
and if i try to put beck 2.08.HSPL with HSPL2_run or HSPL4 he pop-up me some CRITICAL ERROR
Flow: 00000003
Error code: 00000004
Description: Bad model ID!
Do you know what can i do? I really need help...
Thanks a lot again..
Hi rpedro82
did you find any solution for your problem ? I'm facing the same problem and I'm still on the same point even if I tried all the members' suggestions here (even for the freezer) :/
Cheers,
GJ.