Related
I have just tried flashing WM6 on to a Friends QTEK 8500, it went wrong Doh!!!.
I had already last Friday put on it the version with non wroking GPRS and this went without issue. I then reflashed my own one with a GRPS working version (went without a problem) and then tried his. I can get it into the boot loader screen but nothing else. I have tried SD card flashing (3 cards) 1x 512MB Card and 2 x 2GB card all formatted as FAT32 with file on the root the phone searches for it but doesnt find it.
Please any advise.
vallancen said:
I have just tried flashing WM6 on to a Friends QTEK 8500, it went wrong Doh!!!.
I had already last Friday put on it the version with non wroking GPRS and this went without issue. I then reflashed my own one with a GRPS working version (went without a problem) and then tried his. I can get it into the boot loader screen but nothing else. I have tried SD card flashing (3 cards) 1x 512MB Card and 2 x 2GB card all formatted as FAT32 with file on the root the phone searches for it but doesnt find it.
Please any advise.
Click to expand...
Click to collapse
First of all, REMEMBER, your phone is NOT bricked until it goes to BOOTLOADER mode.
Have you made SuperCID before flashing? What firmware are you trying to flash via bootloader mode?
Erofich said:
First of all, REMEMBER, your phone is NOT bricked until it goes to BOOTLOADER mode.
Have you made SuperCID before flashing? What firmware are you trying to flash via bootloader mode?
Click to expand...
Click to collapse
When you say booloader mode what does that look like. At the moment if I reboot the phone I get the HTC Mobility windows by Erofich screen.
When you hold down camera and record button and then power on the device I get brifely the white scrren looking for SD card it then goes to the tri-colour screen and does nothing.
I beleive I have CID it as I did the same on this as I did on mine i.e. ran the unlock according to the sticky.
I than put on this
Windows Mobile 6 AKU 0.5.0 (5.2.1711 Build 18165.0.5.0) WWE v5c
Yours i beleive (excellent work by the way)
and it all worked fine bar GPRS I relay needed GPRS so I used
http://forum.xda-developers.com/showthread.php?t=368715
using the clean one which updated fine on my phone but when i tried it on my friends it fell over at about 83% I followed the recovery intructions but this did not work.
When you get into bootloader screen by pressing RECORD and CAMERA buttons, then you MUST flash back to the STOCK ROM first. You can't flash any custom WM6 at this point. Only AFTER you have the stock ROM flashed, you can use SDA_ApplicationUnlock.exe to app unlock the phone, and copy the SoftSPL into the phone. Then run SPL.lnk.
To summarize: The built-in bootloader CANNOT flash WM6 and can ONLY flash a stock ROM. Once you go back to stock, you can then try to flash WM6 again. Anytime a flash fails, you must go back to stock first, then try again.
GnatGoSplat said:
When you get into bootloader screen by pressing RECORD and CAMERA buttons, then you MUST flash back to the STOCK ROM first. You can't flash any custom WM6 at this point. Only AFTER you have the stock ROM flashed, you can use SDA_ApplicationUnlock.exe to app unlock the phone, and copy the SoftSPL into the phone. Then run SPL.lnk.
To summarize: The built-in bootloader CANNOT flash WM6 and can ONLY flash a stock ROM. Once you go back to stock, you can then try to flash WM6 again. Anytime a flash fails, you must go back to stock first, then try again.
Click to expand...
Click to collapse
I am trying RUU_STAR100_3.6.251.0_02.67.30_QtekEUR_Ship I believe this is an original version 5 rom?
GnatGoSplat said:
you can use SDA_ApplicationUnlock.exe to app unlock the phone
Click to expand...
Click to collapse
This method works on Cingular ROM only, not Qtek.
vallancen
Hold CAMERA and RECORD button and press power button. When it goes to Bootloader tricolor mode connect your device to PC and run official Qtek 8500 RUU. Then make a reg (app) unlock:
Download regeditSTG2 which is digitally signed: http://4pda.ru/forum/attach/387522/regeditSTG2.zip
Then install it and change some registry values:
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 2
-> change to 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 16
-> change to 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 128
-> change to 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101a": Dword = 1
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101b": Dword = 1"
Click to expand...
Click to collapse
copy SoftSPL to the root of your device and run SPL.lnk
Then run WM6 RUU
Erofich said:
This method works on Cingular ROM only, not Qtek.
vallancen
Hold CAMERA and RECORD button and press power button. When it goes to Bootloader tricolor mode connect your device to PC and run official Qtek 8500 RUU. Then make a reg (app) unlock:
copy SoftSPL to the root of your device and run SPL.lnk
Then run WM6 RUU
Click to expand...
Click to collapse
When I plug into PC (XP SP2) and run the Qtek 8500 RUU it just times out and says it cant find device.
vallancen said:
When I plug into PC (XP SP2) and run the Qtek 8500 RUU it just times out and says it cant find device.
Click to expand...
Click to collapse
I have two phones one did work and one did not the one that worked shows version 1.02 on the tri colour screen the one I am having problems with shows 3.06 not sure if this is relevant.
Try removing the battery for about 30-seconds (or just removing the battery cover) and then put it back on. With the phone OFF, hold RECORD and CAMERA and plug in the USB while holding those buttons. It should go to the Bootloader. Run the QTEK RUU immediately after doing that.
If you sit at bootloader very long (more than a minute or so), for some reason it times out and the RUU won't work. It could be that's what's happening.
GnatGoSplat said:
Try removing the battery for about 30-seconds (or just removing the battery cover) and then put it back on. With the phone OFF, hold RECORD and CAMERA and plug in the USB while holding those buttons. It should go to the Bootloader. Run the QTEK RUU immediately after doing that.
If you sit at bootloader very long (more than a minute or so), for some reason it times out and the RUU won't work. It could be that's what's happening.
Click to expand...
Click to collapse
Tried that a couple of times just to make sure I was doing it correctly it goes into the tri colour screen I pressed the reflash option on the PC 1 second later this then sits there for a minute or so and times out "ERROR [260]" the phone did come on and has a USB in the bottom left corner so I presume the connection to the PC is OK.
I have just re-done mine again using the NEO rom (very nice) to make sure I am not going mad and that I did it correctly and this all went without a hitch.
Is there anyway I can get the phone to boot of a SPL on an SD Card I think if I could do this then I could get it back to 5 and start again.
No, it will only boot off the built-in SPL in ROM.
Did you try using the OEM .nbh file, naming it STARIMG.nbh and putting it on the SD card?
GnatGoSplat said:
No, it will only boot off the built-in SPL in ROM.
Did you try using the OEM .nbh file, naming it STARIMG.nbh and putting it on the SD card?
Click to expand...
Click to collapse
Yes tried that made sure formatted FAT32 etc. I know the SD card is ok because if I take my working phone and run the SPL link with the card in my good phone it finds the file and asks me if i want to reflash it. The non working phone with SPL3.06 does not do this.
You are not alone.
The bad news - the person in the post ended up having to exchange the phone.
It could be there's a bug in 3.06 SPL? Seems to be the case because I've flashed bad ROMs many dozens of times on my Cingular 3125 StarTrek and not once did I have any trouble flashing OEM ROM back on it.
Can I write the flash at a lower level with any tools i.e. pdocwrite or seomthing like that?
I don't believe so. Those programs require an Activesync connection (copies files to the phone). You could try the MTTY method, but I don't know if that works on StarTrek. I think it's some kind of terminal access into the bootloader, but what I've said so far is the extent of my knowledge about it.
vallancen said:
I have two phones one did work and one did not the one that worked shows version 1.02 on the tri colour screen the one I am having problems with shows 3.06 not sure if this is relevant.
Click to expand...
Click to collapse
I have a similar problem on a 3125 and the phone reports V4.01. I acquired the phone in this condition, so don't know how that came to be. When I try to update via USB, it tells me I need a newer update tool (to match the 4.01, I assume). What error message are you getting when you try to update via USB?
I have been struggling to flash (again) the great pro V2 rom, but I always used my VMWare based XP windows version on my Vista laptop. Today I could use a genuine XP Laptop and I could make a connection and start the upgrade!
Sounds good? That's what I thought too, until the upgrade stopped at 70% (and I didn't touch anything), because of a connection error. I followed the text on my PC screen and I finally it started flashing again for a few seconds and then my startrek suddenly restarted, but it stops at the first splash screen! I tried to get my device back to bootloader mode (push 2 soft buttons and start), but no bootloader mode, only the 1st splash.
I solved the problem.
Thank you for this thread
I tried flashing a new ROM to my i-mate smartflip and thought I had killed it, but going back to the wm5 OEM as suggested on this thread worked and I still have my phone. Now, am I brave enough to try upgrading it to wm6.1 (or even 6.5) again... Once again, many thanks!
somebody can me give the oem rom because i am same problem too on the secreen 3.06 i cant flashing anytihing rom somebody must me help
I have a problem:
I flashed my hd2 from a stocked rom 1.42 dutch version, with hspl 1.42. I installed a custom rom from: HTC HD2 Laurentius WWE 21891UltimatePOWER.
it worked fine for 2 or 3 days and then it stocked, i reseted the phone and
When i turn on my HD2, i get a white screen. and it doest go away. Even after softreset (volume button down in bootloader)
When i go in to bootloader i see this screen:
Pb81100 hx-bc
Spl-1.42.hspl xe
0x05
Cotullahspl 0x30
Click to expand...
Click to collapse
When i try to instal a rom by going in to bootloader en then start in win xp the update wont start, it stocked at 0 %
Then i tried to flash a orginal romt by sd:
it stocked at 7 % and i get this screen:
_______________________RUUNBH
PB81100___HX-BC
SPL-1.42.__hspl___XD
________________0x05
CotullaHSPL______0x30
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
- Then i tried to flash a radio rom by activesync, in xp it wont start,
- i tried flashing by sd and it stocked on 98%
- I tried different to install a rom and radio rom by vista, but also no succes
- I tried task 29 (by the Attached Task29 into a single exe.) to erease all data from the phone, but in windows by activesync it wont start
i tried al the above from windows 7.
Is there anyone that can help me, please i getting very desperate.
VERY VERY IMPORTANT! Try and read 2-3 times what is written here http://forum.xda-developers.com/showthread.php?t=609477
Only afterwards proceed to the following :
First of all....try and use Windows Vista or Windows 7.
Second of all....do not try to use task 29 because its a bit more complicated and it involves some drivers and so on!
Use this little thing here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 and after its completed....flash a proper radio something like 2.08.50.xx which you can find on Radio dedicated section here http://forum.xda-developers.com/showthread.php?t=611787
After all these....flash a custom ROM but be careful to be one suited with your radio! Which is a radio appliable for most of custom ROMS BUT be VERY careful!
Another thing.....do not flash from SD Card....Use the CustomRUU tool and flash it via ActiveSync!
Do you get any particular error message? When in bootloader mode, does "usb" show at the bttom of the screen? If so, try moving to a different usb port, preferably at the rear of the pc, or try different cable or even different pc. If still no luck, try uninstalling and then re-installing the latest version of Activesync.
The White Screen issue sounds like the incorrect radio version for the rom. I'm not familar with the details of the particular rom, but there are certain rom/radio combinations that will do that if they do not match eg running a 2.10 based rom with a x.xx.51.xx radio. The phone works intially until a reset and then hangs.
viperd said:
VERY VERY IMPORTANT! Try and read 2-3 times what is written here ......
Click to expand...
Click to collapse
Thanks for the replay
I tried, flashing by activesync. i flashed it the first time by hspl (the tread you link to) and then by activesync. But like i said, the hd2 stops at a white screen, so i tried by every possible way i could think of. Also i tried task 39 by the tool you mention, but it still does not work.
But i will correct my ts.
@clydeb1
I tryd to flash different radioroms, but if it try by activesync it wont start and by sd-flash it stocks at 98%, but i will try a different active sync
Okay,
I tried the following options:
- I installed a newest activesync and tried to instal an new rom under windows xp. The update stocked at 0% and i tried to install radio rom, with the same results
- I installed the windows mobile on windows 7, and tried the same as in windows xp, and still the same results.
Then i tried flashing every rom from the site by the sd-method (after every bad flash i formatted the sd-card with fat32)
With the sd method the phone stocked at 99% and then gives the next images:
00018003
LEOIMG.nbh - Fail
Radio_V2Fail
Update terminate
update fail
Click to expand...
Click to collapse
IS there any one how has a solution for this problem
Ok....try from the beginning!
1.Get from here http://forum.xda-developers.com/showthread.php?t=611433 HSPL2_RUN.zip (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....http://forum.xda-developers.com/show...3&postcount=19
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
viperd said:
Ok....try from the beginning!
1.Get from here (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
Click to expand...
Click to collapse
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Give the phone to someone who can get it to work??
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
korenbloem said:
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Click to expand...
Click to collapse
Thanks mate, if my suggestion doesn't work hopefully you can help him.
xmoo said:
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Click to expand...
Click to collapse
@Korenbloem,
A simple hardreset would have fixed your issue as well.
Instead of all kind of panic experiments like mtty/ flashing radios/roms from sd you could have come to me and I would have helped you.
You flashed a very old rom from the rom archive but never the less that rom is intensivily tested by me and the beta team.
I have no idea what kind of software you installed/tweaks you did or anything else but also with installing the wrong software it could cause the rom not to boot anymore.
Sorry to tell you but these 'bricking' stories are mostly caused by unexperiened users and it
making me sad to see more people are opening threads like this blaming a rom and causing a panic reaction in public destroying our work.
I realy hope you fix your device and I will try to help you but this isn't a rom issue.
Leo
Laurentius26 said:
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
Click to expand...
Click to collapse
Thanks for the adivse, but i already tried that with an orginal rom, but i will try it again, mabey there is a difference with a shipped rom.
The first thing i did was a hard reset, but that did't worked. (the phone is in this shape for 1 month now).
Second. I am not blaming you or anyone. I flashed the wrong radio rom i think (cant remember witch one) And that is my own fault. I never wanna make the suggestion that it is because of youre rom.
I took a risk by flashing my phone. and i is my responsibility.
Edit: I tried a shipping rom nld. But it gives the same error as always, only after 7%. But thanks for the advise
@ Xmoo, First of al thank you that you want to help with a sollution. But what does that mean a goldcard and what are the consequences of using it.
Laurentius26 helped me with fixing my device.
The problem was the radio. and by flashing a factory rom from t-mobile, the hspl was reset to spl 2.00. After that he flashed a orginal shipped rom (the orignal one from my device). And the rom is fixed again SPL 1.66 is now on the device.
Laurentius thanks for al the help!!!!!
HD2 bricked?
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
vanbasten88 said:
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
Click to expand...
Click to collapse
Do you have a branded Leo? If so, enter bootloader (remove battery, press volume down, insert battery), connect via usb (maybe you have to wait for driver installation), start the latest *.exe from your operator/carrier...
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
andreftx said:
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
Click to expand...
Click to collapse
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
silverwind said:
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
Click to expand...
Click to collapse
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
andreftx said:
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
Click to expand...
Click to collapse
The 1.66 ROM you posted above has radio version 2.06.51.07 with it. So have you considered trying to flash that radio version and then flash the ROM. I know if you get the ROM to flash it will flash that radio anyway. But you seem to think you flashed a wrong radio so just thinking out loud here.
Hello everyone,i have changed my rom several times,everything was ok but as i run task29,and then when i lunched Miri & Dinik WM6.5.x 23569 v.17.4(2),my HD2 doesn't load and the blank screen that has the htc logo doesn't disappear.i have done every thing that it was said in this site(sd flash and so on,putting leoimg.nbh in the sd card and so on...) but it didn't work!!!
I wonder what should i do now?is it a hardware problem?
moharzani said:
Hello everyone,i have changed my rom several times,everything was ok but as i run task29,and then when i lunched Miri & Dinik WM6.5.x 23569 v.17.4(2),my HD2 doesn't load and the blank screen that has the htc logo doesn't disappear.i have done every thing that it was said in this site(sd flash and so on,putting leoimg.nbh in the sd card and so on...) but it didn't work!!!
I wonder what should i do now?is it a hardware problem?
Click to expand...
Click to collapse
can you manually get into bootloader?
yes,with soft reset and holding the vol down button.
and what does it say next to spl in bootloader?
sorry,it seems that the information that i gave,wasn't so complete to be answered,
it is SPL-1.42.000.
ok, so any spl that ends .0000 is stock so you dont have hspl installed, and so cannot flash custom roms or radios.
This no doubt happened when you tried to flash a stock rom from sd card, because even if the sd flash fails, it will have reset the spl. (Example, say you have an o2 locked phone, you try to flash a tmobile stock rom, from sd card, the first thing it does is remove hspl, and THEN it does the cid check, , finds that its a tmobile rom and an o2 phone so the flash fails, making you think it just failed, nothing more, but in reality it has already flashed the spl removing hspl)
Get hspl2
run it, choose the hspl version you want (1.42.hspl, 1.66.hspl, 2.08.hspl, it doesnt really matter)
pick any rom you want to flash and flash it from usb.
Let us know how you get on.
hey sam,that was great!you made my hd2 back to life.thanks a lot for your help my dear.
i tried many ways to fix it,but the rom update failed all the time.i tried to flash hd2 through micro sd,so i formatted my memory card and then i rename "ruu_signed.nbh" to "LEOIMG.nbh", and i reset hd2 while holding vol down button.then the loading screen appeared, i thought that i solved the prob but i was wrong and the loading screen was still there,i even waited for a hour!!!but nothing changed.the last option was to state my prob here,and i did,and i received a reply from you sam,i dont know how can i thank u,only i can say many thanks and you did me a very big favor!
my pleasure.
as for the favour,, do something nice for someone you don't know next time you get chance.
Hi all. Just wanted to let everyone know: NEVER GIVE UP. I task2a my htc leo twice (different times) and "BRICKED" it in that I could not flash any rom back to it. It has HSPL3 and trying everything including removing HSPL and going back to SSPL (HSPL 2.08.0000) I got nowhere. NO ship/stock or custom roms would flash at all by USB and when done by LEOIMG.NBH I'd get RADIO_V2 RSA FAIL etc. I tried using the various RUU executable: Romupdateutility.exe, CustomRUU.exe, ruu.exe (dexter series), and still had problems. I never lost HSPL or bootloader however... In the end I solved it like this:
1) CRITICAL YOU HAVE A FULL BATTERY FIRST AND FOREMOST ELSE IT DOESNT WORK OR UPDATE AT ALL. USE EXTERNAL CHARGER/OTER PHONE.
2) I connected by MTTY and re-did Task 2a, and a Task 28, Task 28 55 aa, and then a task 29.
3) I kept trying various different LEOIMG.NBH files including RADIOs, Custom roms with only OS.NB inside, etc etc etc.
4) In the END:
You will have to use your LEOIMG.NBH on <4gb SD CARD from the STOCK default rom the phone came with....
But: It will probably not (for some reason) work first TEN or so times !!! (weird?)
I kept trying doing ruu.exe in between each SD card attempt and also kept removing/swapping HSPL/2.08.0000 and going in and out of MTTY doing 2a, 28, and 29 OVER AND OVER AND OVER. Ultimately I know this is confusing (my explanation) but I am simpy saying my leo was gone and I did not give up so DO NOT GIVE UP. I sat there 12 hours+ doing this over and over and GOT IT BACK TWICE NOW (yes - I did 2a task twice for certain reasons)... USEFUL ROMS/APPS:
Task29.exe (containg single checksum-ok but BLANK - ruu_signed.nbh)
Telstra Stock ROM
Telstra (HTC website) signed update ROM.
Latest LEO radio
Dexter-with CHT2 and companion ruu.exe (used with dexter and other .nbh)
Xanny-Tech-Evolution via SD Card.
HSPL3_PKG.EXE
magldr 1.11 (by RUU and SD).
In the end YOU WILL FIX IT OK. I'm pretty tired now so I will go over this and clean it up later but KEEP PERSISTING AND HAVE FAITH: if you have HSPL and MTTY and SD you can and you will fix it.
---
edit:
OK, after stock telstra LEOIMG.NBH ok... wanted magldr back... did hspl3... fine... then did Task29.EXE(for radio rom 2.08 576 ram ok) by the EXE/RUU: DO NOT DO THIS... it fails and you have to start again:
after task29.exe (radio 2.08 not-MTTY) with FAILURE - I put the ruu_signd.nbh for this onto SD card and flash - fine. Then did MAGLDR.NBH the same (LEOIMG.NBH) and all OK. Then clockwork and update.zip for PPC-Windows7-Android.
----
Thanks DFT and Cotulla.
Hurry up and release NAND WP6 and WP7 NAND boot
Making donation $.
Cool that it works for you. But the steps in your description does not give me enough confidence that it will work for anyone else.
Or maybe someone else can verify this method?
Nice!
This was very inspiring! I hope it does work for everyone. As for me I did try for the nth time and well no luck for me, tried a lot of variations, roms, task29, radios but still unsuccessful. Guess for me customer service is the only way. Good luck to the others!
i have my friend device which is in similar situation tried everything but it dont wont work. dont know how to fix. my friend cant even go to tmo since he bought off ebay.
shah_vm said:
i have my friend device which is in similar situation tried everything but it dont wont work. dont know how to fix. my friend cant even go to tmo since he bought off ebay.
Click to expand...
Click to collapse
Just send it through tmo repair center, its gonna cost $120-$170
Hi guys, i'm stuck on:
PB81100 HX-BC
SPL-2.0.8.HSPL 8G XE
RIFFBOX 0x05
and white screen without htc logo, can i solve this? or it is bricked up?
Thanks in advance
the same here
I got out of bricked situation by extracting only the SPL file from the stock rom using OS builder.Renamed it leoimg.nbh and flashed it using SD card 2 GB /sandisk/.It appeared stuck on the "loading" screen and I had to remove the battery not sure if I'd succeeded.The first sign that something might have gone right was the green light showing fully charged battery,cause despite "common sense" I put the battery back in and put the phone to charge.After taht I used the RUU_signed file from the same stock rom I took the SPL from.
i must try harder...
i spend already to much hour on this pr ...i dont give up
i connect MTTY via USB button in win 7 i make this command task 2a , task 28 ,29
i want to find a STOCK ROM for my phone but i can't find a good one CID is HTC___001
i need a GOLD card i think... to unlock
after i make the info 8 cmd in MTTY window last line say OS not FOUND ...
Hy!
I did a stupid thing, with the following. I copyed an LEOIMG.nbh file to my formatted sd card, so I get an SPL-1.42.0000, but I can't flash any HSPL to my device, because the HSPL setup writes out USB connection error. Neighter can I flash for example the official 1.66 rom, the installation stops after 1%, and writes INVALID VENDER ID. What can I do?
Very siple but you need lots of time for it. The rom you flashe has spl 3.03 on it and so it doesn't allow you to flash any other spl on it. What you can do is you have to search for old stock roms in the native language of your phone. As long as the phone keeps giving you error when trying to flash a stockrom with you sd card, it means you have not yet gotten the right stockrom for you phone so you have to try with different old stockroms till you get the right one.
After that. you'll be able to flash whatever you like. Hope it helps.
But remember, you need time and patience.
Abdul9. said:
Very siple but you need lots of time for it. The rom you flashe has spl 3.03 on it and so it doesn't allow you to flash any other spl on it. What you can do is you have to search for old stock roms in the native language of your phone. As long as the phone keeps giving you error when trying to flash a stockrom with you sd card, it means you have not yet gotten the right stockrom for you phone so you have to try with different old stockroms till you get the right one.
After that. you'll be able to flash whatever you like. Hope it helps.
But remember, you need time and patience.
Click to expand...
Click to collapse
Thanks, I will try it. This stockrom is 1.66?
zoldya said:
Hy!
I did a stupid thing, with the following. I copyed an LEOIMG.nbh file to my formatted sd card, so I get an SPL-1.42.0000, but I can't flash any HSPL to my device, because the HSPL setup writes out USB connection error. Neighter can I flash for example the official 1.66 rom, the installation stops after 1%, and writes INVALID VENDER ID. What can I do?
Click to expand...
Click to collapse
You can also download HSPL 4 and use it to downgrade your SPL. To do this manualy put your HD2 into bootloader by holding the volume down button and pressing the power(end) butom momentarily. Once in bootloader connect your HD2 to your computer via USB cable wait until you see USB in the white bar of thd bootloader and run the HSPL 4 on your computer. It will ask you which SPL or HSPL you wish go flash select the proper SPL version to flash to your HD2 and you should be good to go. Hint the SPL version will have zeros at the end of them and the HSPL version will not. Example SPL 2.08.0000 HSPL 2.08. Hope this helps.
T-Macgnolia said:
You can also download HSPL 4 and use it to downgrade your SPL. To do this manualy put your HD2 into bootloader by holding the volume down button and pressing the power(end) butom momentarily. Once in bootloader connect your HD2 to your computer via USB cable wait until you see USB in the white bar of thd bootloader and run the HSPL 4 on your computer. It will ask you which SPL or HSPL you wish go flash select the proper SPL version to flash to your HD2 and you should be good to go. Hint the SPL version will have zeros at the end of them and the HSPL version will not. Example SPL 2.08.0000 HSPL 2.08. Hope this helps.
Click to expand...
Click to collapse
I have tried that, but after a few minutes - when it tries connect to the device - the HSPL setup writes out an error message;
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
but i don't know why, because during the installationvI see USB in the white bar of the bootloader - the device manager on the notebook shows the connection too. :S
Abdul9. said:
Very siple but you need lots of time for it. The rom you flashe has spl 3.03 on it and so it doesn't allow you to flash any other spl on it. What you can do is you have to search for old stock roms in the native language of your phone. As long as the phone keeps giving you error when trying to flash a stockrom with you sd card, it means you have not yet gotten the right stockrom for you phone so you have to try with different old stockroms till you get the right one.
After that. you'll be able to flash whatever you like. Hope it helps.
But remember, you need time and patience.
Click to expand...
Click to collapse
I just finished with the 1.66 OSPL roms http://http://forum.xda-developers.com/showthread.php?t=623283 but the problem was the same with each one. Should I try the 3.14 rom-s too?
zoldya said:
I just finished with the 1.66 OSPL roms http://http://forum.xda-developers.com/showthread.php?t=623283 but the problem was the same with each one. Should I try the 3.14 rom-s too?
Click to expand...
Click to collapse
Have you tried to restart your PC and or change another USB port of your PC?
zoldya said:
I have tried that, but after a few minutes - when it tries connect to the device - the HSPL setup writes out an error message;
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
but i don't know why, because during the installationvI see USB in the white bar of the bootloader - the device manager on the notebook shows the connection too. :S
Click to expand...
Click to collapse
Try the above post by silverwind and try another USB port, another computer, and another cable if you have too. Something just does not sound right about this. I am looking at this.
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
Click to expand...
Click to collapse
Just keep trying man I think you might just have a simple problem here.
Heck reset your notbook if you think it might help.
I have tried that too, and didn't solve the problem... :'(
Do you think that GoldCard method would help?
Hi. I have the same pronblem. I have a UK HD2 that was originally on Tmobile. I flashed 2.08HSPL using HSPL4 & upgraded the ROM to the standard WWE_3.14. A long story short... after playing around with SD Android & a few other utilities I wanted to make a clean start, so my plan was to use HSPL4 to remove the HSPL before then re-installing it & reflashing the ROM. Unfortunately I now seem to be stuck in SPL2.08.0000. HSPL4 just gives the same error:
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
I have also tried flashing a stock ROM via SD (renamed leoimg.nbh), but I can't get passed the bootloader displaying 'serial'.
Any ideas?
Chameleon846 said:
Hi. I have the same pronblem. I have a UK HD2 that was originally on Tmobile. I flashed 2.08HSPL using HSPL4 & upgraded the ROM to the standard WWE_3.14. A long story short... after playing around with SD Android & a few other utilities I wanted to make a clean start, so my plan was to use HSPL4 to remove the HSPL before then re-installing it & reflashing the ROM. Unfortunately I now seem to be stuck in SPL2.08.0000. HSPL4 just gives the same error:
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
I have also tried flashing a stock ROM via SD (renamed leoimg.nbh), but I can't get passed the bootloader displaying 'serial'.
Any ideas?
Click to expand...
Click to collapse
Did you place the leoimg.nbh on the root of your SD card? Also was tbe dile you renamed originaly named RUU_signed.nbh?
T-Macgnolia said:
Did you place the leoimg.nbh on the root of your SD card? Also was tbe dile you renamed originaly named RUU_signed.nbh?
Click to expand...
Click to collapse
Yes on both counts... I've even tried a complete 'long' reformat of the SD card first using the Panasonic SD Formatter, before putting the leoimg.nbh at the root.
I'm guessing that my stupid mistake is downgrading to SPL2.08.0000 whilst having a generic version of the 3.14 ROM installed. I guess I should have downgraded the ROM to an original Tmobile one first...
Could i ask what operating system you guys are using cos this problem could have less to do with the phone than it has to do with the operating system on the pc. I was trying to flash some roms on some old devices using Windows 7 but this didn't seem to work but it magically worked when i used Windows xp. I hope this works.
About the wrong Vendor problem, this just means the rom flashed is not recognized by the phone as the official one, i also had that problem and after flashing a official rom in the language of my phone, the problem was solved. I used the 1.66 rom so that i could flash hspl or else it might be impossible to do so.
Or as someone suggested you might try the hspl4 (never knew that existed) but try using Windows xp and if the problem persists try reinstalling your operating system (on your pc). I know it a lot of work but its just to rule out that the problem is from the pc.
Another thing i want to make sure of is if the phone is working normally with the rom on it or is there no rom at all?
Abdul9. said:
Could i ask what operating system you guys are using cos this problem could have less to do with the phone than it has to do with the operating system on the pc. I was trying to flash some roms on some old devices using Windows 7 but this didn't seem to work but it magically worked when i used Windows xp. I hope this works.
About the wrong Vendor problem, this just means the rom flashed is not recognized by the phone as the official one, i also had that problem and after flashing a official rom in the language of my phone, the problem was solved. I used the 1.66 rom so that i could flash hspl or else it might be impossible to do so.
Or as someone suggested you might try the hspl4 (never knew that existed) but try using Windows xp and if the problem persists try reinstalling your operating system (on your pc). I know it a lot of work but its just to rule out that the problem is from the pc.
Another thing i want to make sure of is if the phone is working normally with the rom on it or is there no rom at all?
Click to expand...
Click to collapse
Hi. Thanks for the input. The problem is getting even more frustrating! I've tried buying a new 4GB micro SD card (both are class 4). I have tried both TMO_UK_1.72 & TMO_UK_1.43. Both ROMs were downloaded from HTC using the correct phone's serial, so they should be the correct ones.
With the original SD card I can't get passed the bootloader screen & it just stays in 'serial' mode. With the new SD card it moves on to 'loading...', but then just hangs. I haven't yet seen the word 'searching' as described in the [TUT] Flash your ROM / Radio via microSD.
To clarify, the phone boots fine with the installed 3.14 ROM, but I can't get away from SPL 2.08.0000 or flash any other ROM.
Chameleon846 said:
Hi. Thanks for the input. The problem is getting even more frustrating! I've tried buying a new 4GB micro SD card (both are class 4). I have tried both TMO_UK_1.72 & TMO_UK_1.43. Both ROMs were downloaded from HTC using the correct phone's serial, so they should be the correct ones.
With the original SD card I can't get passed the bootloader screen & it just stays in 'serial' mode. With the new SD card it moves on to 'loading...', but then just hangs. I haven't yet seen the word 'searching' as described in the [TUT] Flash your ROM / Radio via microSD.
To clarify, the phone boots fine with the installed 3.14 ROM, but I can't get away from SPL 2.08.0000 or flash any other ROM.
Click to expand...
Click to collapse
Ok here is a couple of options for you. One go to www.t-mobile.com if you have a T-Mobile HD2 and type HTC HD2 upgrade in the search box on the home screen of the website and you will find the official T-Mobile 3.14 ROM. You will have to enter your IMEI number under your battery to download it. Download this ROM and then follow the steps to flash it via SD card, hint you will have to rename the original .exe file to .zip to gain access to the .nbh file. Also you can download and run HSPL 4 on your HD2 and select SPL 3.03.0000 but the official ROM will change it to SPL 3.10.0000 if you flash via SD card
Its a common problem i think if you are trying to flash a rom via sd card with a sd card higher than class two. Many here have encountered such problems.
According to your description, it will seem that it is as i suspected, the pc doesn't seem to recognize the phone and this could mean you have a defect usb cable or the useport itself is not funtioning properly. Try holding the phone in your hand with the usb in and support the usb with your hand to make sure the usb is indeed in the phone and see what happens. My usb cable is a little bit loose so when i want to flash anything, i use my hand to support it or i place my phone on a smoot surface and make sure the usb cable is in it.
zoldya said:
Hy!
I did a stupid thing, with the following. I copyed an LEOIMG.nbh file to my formatted sd card, so I get an SPL-1.42.0000, but I can't flash any HSPL to my device, because the HSPL setup writes out USB connection error. Neighter can I flash for example the official 1.66 rom, the installation stops after 1%, and writes INVALID VENDER ID. What can I do?
Click to expand...
Click to collapse
Chameleon846 said:
Hi. I have the same pronblem. I have a UK HD2 that was originally on Tmobile. I flashed 2.08HSPL using HSPL4 & upgraded the ROM to the standard WWE_3.14. A long story short... after playing around with SD Android & a few other utilities I wanted to make a clean start, so my plan was to use HSPL4 to remove the HSPL before then re-installing it & reflashing the ROM. Unfortunately I now seem to be stuck in SPL2.08.0000. HSPL4 just gives the same error:
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
I have also tried flashing a stock ROM via SD (renamed leoimg.nbh), but I can't get passed the bootloader displaying 'serial'.
Any ideas?
Click to expand...
Click to collapse
Ok do to some recent personal experience and some other members problem of late. I suggest both of you do this go to www.windowsmobile.com/getstarted and download the most recent version of WMDC wich has updated drivers in it that seems to solve somd problems with flashing via USB especially if you are using a 64 bit system. Just so both of you know unless your HD2 shows up as "HTC USB Sync" in the device manager while connected via USB while in bootlaoder you do not have the correct drivers installed and any flash will fail.
T-Macgnolia & Abdul9: Thanks for that, however mine is a UK Tmobile HD2 & the .com site is only for US ones (it doesn't recognise UK IMEI's). If I go via the UK site it just links me to the HTC update site for the RUU_Leo_S_TMO_UK_3.14.110.1_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship (& also the 1.72 & 1.43 versions. I have tried all of these via both SD card & via USB. I have also tried HSPL4, HSPL3 & HSPL2. All options have failed. I have tried from Win XP Pro & Win 7 Ultimate (both 32bit) with two different USB leads. I have also tried a 3rd SD card (which ends up stalling at the 'loading' screen. The phone flashed fine prior to removing 2.08HSPL with HSPL4.
I think that the problem is not the SD card or the USB lead, but is the problem that I've now got a Tmobile (UK) phone with spl 2.08 & a WWE_3.14 ROM installed - this should obviously not normally be possible. I can't flash back to HSPL & I can't downgrade to any other ROM.
Does anyone have any idea how I can 'fool' the phone into letting me change the ROM?
I've been reading about Task29, but it says don't do this unless you have HSPL (which I can't get!). I don't want to brick the phone (because it still runs!), but I want HSPL back otherwise I can't reinstall Android on SD.
Furthermore, I don't think this is a USB driver issue, as it flashed fine before & it's occurring across different PC's & operating systems.
It's an incompatibility between a branded Tmobile with SPL & a WWE HTC ROM... I just need to get out of the loop I'm stuck in!
Hey Chameleon I know you don't think it is a problem with the drivers cause it was flashing fine before. But what I do not think you have taken into account is that you came from a older ROM and you had the right drivers to work with that ROM or the update for that ROM. But you now have a 3.14 ROM and this is a newer ROM that probably requires different drivers. I mean Microsoft did not create a new WMDC with updated drivers if it was not needed for the 3.14 ROMs as they are the most recent official ROM versions. Microsoft is the one that comes out with the new ROM versions too, the carriers just add their bloatware to them. Do you see my train of thought here? Also make sure you are usinv SD card that is 500MBPS to 8GB that is formated with Fat 32.
T-Macgnolia said:
Hey Chameleon I know you don't think it is a problem with the drivers cause it was flashing fine before. But what I do not think you have taken into account is that you came from a older ROM and you had the right drivers to work with that ROM or the update for that ROM. But you now have a 3.14 ROM and this is a newer ROM that probably requires different drivers. I mean Microsoft did not create a new WMDC with updated drivers if it was not needed for the 3.14 ROMs as they are the most recent official ROM versions. Microsoft is the one that comes out with the new ROM versions too, the carriers just add their bloatware to them. Do you see my train of thought here? Also make sure you are usinv SD card that is 500MBPS to 8GB that is formated with Fat 32.
Click to expand...
Click to collapse
WOW! I've got the problem sorted! This can't be a coincidence... I haven't done anything different to my PC, but I got an 'unlock' code through for my phone this morning (£5.99 on Ebay) & it worked fine. I though "why not" & tried HSPL4 again. With no other changes it worked absolutely fine this time & I now have 2.08HSPL installed.
Presumably by unlocking my my phone from Tmobile it has also removed the 'you're using the incorrect ROM' problem.
Thanks for everyones input on this. I maintain that XDA-Developers is one of the best Forums around (not just within the mobile phone arena).