Yah,..
My X10, now stuck in Leter " Sony Ericsson " .
That's my false,..
I did the stupid step for put the files on system\Framwork...
Ok,.. Forgeted..
I need help now,...
1).How Put the Firmware-res.apk to system\Framework
Using ADB ,might not possible because the computer not recognize my x10 as ADB anymore , and usb debuging status was not checked .
2). I've tried using Update Service Setup.exe, but still got the problem on Power off the phone.
> As we know , shuting down/(power off ) by removing battery is not posible in this device.
Step for updating is :
-Press and hold back button on the x10, while pluging the usb cable into x10
-Continue holding back button until the NEXT
Simple or big problem?
> How to Power Off the Phone , since the phone was stuck in logo /"sony ericsson"
Thanks,...
Why not leave the battery to drain, then plug into the computer?
Dricos said:
Yah,..
My X10, now stuck in Leter " Sony Ericsson " .
That's my false,..
I did the stupid step for put the files on system\Framwork...
Ok,.. Forgeted..
I need help now,...
1).How Put the Firmware-res.apk to system\Framework
Using ADB ,might not possible because the computer not recognize my x10 as ADB anymore , and usb debuging status was not checked .
2). I've tried using Update Service Setup.exe, but still got the problem on Power off the phone.
> As we know , shuting down/(power off ) by removing battery is not posible in this device.
Step for updating is :
-Press and hold back button on the x10, while pluging the usb cable into x10
-Continue holding back button until the NEXT
Simple or big problem?
> How to Power Off the Phone , since the phone was stuck in logo /"sony ericsson"
Thanks,...
Click to expand...
Click to collapse
hold power + home. release it when screen goes off. hold back and plug usb in.
timing is all. i had to try it a few time before SEUS released the next button
advice to wait untill you drain the battery is not a solution, it will switch the device off after time, but after you start charging, you will get back to the same situation, the device will start and will get stuck on the same place as now (personal experience)
try this before you reflash you device..
If your phone gets stuck on booting after playing with framework or some other stuff, I've found a way to repair it without reflash :
restart phone, connect it to usb
in adb shell run rootshell command again to gain root (wise to keep it after rooting), the "su" won't work cause it depends on gfx libs and they are not started yet..
mount sdcard with this command : mount -t vfat /dev/block/mmcblk0p1 /sdcard
and put your backed files where they belong.
Good luck!
forced restart as already mentioned in post above, hold power button + home button
it's from this thread
inteks said:
hold power + home. release it when screen goes off. hold back and plug usb in.
timing is all. i had to try it a few time before SEUS released the next button
Click to expand...
Click to collapse
Thanks,
it's solved,...
And now my x10 already get normal again..
but, I have some question :
After SEUS, the buid number has changed to 1.1.A.0.8
( Before SEUS Build Number : 1.1.A.0.36 )
I don't not know what I did, means "downgrade ? " or update ?
darebak666 said:
advice to wait untill you drain the battery is not a solution, it will switch the device off after time, but after you start charging, you will get back to the same situation, the device will start and will get stuck on the same place as now (personal experience)
try this before you reflash you device..
If your phone gets stuck on booting after playing with framework or some other stuff, I've found a way to repair it without reflash :
restart phone, connect it to usb
in adb shell run rootshell command again to gain root (wise to keep it after rooting), the "su" won't work cause it depends on gfx libs and they are not started yet..
mount sdcard with this command : mount -t vfat /dev/block/mmcblk0p1 /sdcard
and put your backed files where they belong.
Good luck!
forced restart as already mentioned in post above, hold power button + home button
it's from this thread
Click to expand...
Click to collapse
Thanks, bro.. for ur advice,
My x10mini was reflashed now ,
It is unrooted phone now
I'll try rooting and try new themes I need your advice...
help help help !!!!! im having the same problem but i tried everything ! but it still dosent work
Simple way,...
Just go to sony ericsson web, and you get the driver and services update..
Update your device through the sonyerricson service updater...
Related
hi can someone please help i tried to flash my xperia x10 mini and failed badly and now when i turn on my phone the logo screen comes up and then just stays on... ive left it for about 20 minutes but still nothing its like its bricked on the logo screen i can restart it but it just does the same again. Ive also tried taking the battery out putting it back in then using the update service to lock it in flash mode while i use binarys flash kit but that doesnt work either. Also the update service just says no software update is available it thinks i already have the latest one please help i will be truely greatful x
Edit :
Ive already tried SEUS, PC Companion, Binary's Flash Kit.
Ive already tried connecting it to the adb but cant get adb to recognise a connected device and all the drivers are installed.
i guess you have, but i've to ask, have you tried the repair option in SEUS/PC Companion?
yeh i have seus says i already have the latest software version installed and pc companion actually wants me to load my phone up to connect it :/ any ideas? x
me too!!
i had the same problem with you...
how to get shutdown this phone?
phone must be shutdown when i want to flashing from SEUS..
and i don't know how to shutdown this phone because the battery....
edit : just connect your phone and use restart (hold power button & middle button)
after reboot, press back button and you will connect with SEUS...
but, my phone already get latest update...and i can't flashing from SEUS...
sob..
ive been shutting down the phone by taking the back off and unscrewing the inside cover. Then you will see the battery cable where you can simply unplug it from the motherboard and then reinsert it.
Edit: I also have connected to SEUS but it says i already have the latest software
Ive taken it to a local phone repairs shop ive given up... they said it'll be fresh and working by tomorrow morning it cost me £20 but its just one of those things en it :/
hey guys
all you need is to follow the instructions on SEUS,
when it tells you that you have the latest software press repair.
and when it say that you should turn off your phone and then reconnect it while pressing the back buttom do the following:
1- connenct the phone to the computer
2- press the 3 buttoms (power + mid buttom + back buttom) then as your phone restarts and vibrate remove your fingers from the power and mid buttoms but maintain pressing on the vack buttom
i hope this will help
Hi all. I have multiple problems in my x10i.it has 2.1 It was rooted and worked fine..few days ago I tried to wipe the phone and did the master reset via xrecovery ..after the restart it just hanged at the boot logo and xrecovery is not working from then....I wanted to update with SEUS via USB... but the phone is not connecting as well...What should I do? PLZ HELP ME GUYZ........
Hi,
Seus doesn't recognize your x10 even if you hold back button while plugging usb (flash mode) ?
This week my x10 2.1 crashed (I suppose it was because of rooting with superoneclick without rebooting immediatly), and wasn't recognized by windows. It was in a loop turnig on/off and only putting off battery could turn it off really. Big Problem.
The only solution I found : putting off battery, pluggin usb cable, holding back button and putting on battery. Back button still hold (like flash mode) until seus recognize x10. Then it runs alone and install rom (after I rooted with flashtools and launched jit optimisation, witch increase truely x10 performances!).
Probably seus not recognize your phone because you have a rooted and custom firmware in your x10 and xrecovery is not working because you did a reset and then you delete some files from your phone, you can reinstall it with the x10flashtool or to make a complete restore firmware whit the same x10flashtool
If SEUS/PCC doesn`t recognize your phone, remove them from PC and reinstall them.
You have an USB driver problem
ohm74 said:
Hi,
Seus doesn't recognize your x10 even if you hold back button while plugging usb (flash mode) ?
This week my x10 2.1 crashed (I suppose it was because of rooting with superoneclick without rebooting immediatly), and wasn't recognized by windows. It was in a loop turnig on/off and only putting off battery could turn it off really. Big Problem.
The only solution I found : putting off battery, pluggin usb cable, holding back button and putting on battery. Back button still hold (like flash mode) until seus recognize x10. Then it runs alone and install rom (after I rooted with flashtools and launched jit optimisation, witch increase truely x10 performances!).
Click to expand...
Click to collapse
nope, phone is not connecting in flash mood..i pulled of the battery and did as u said,,nothings working ......
Take the phone with the warranty for repairing.
mistake_man said:
Probably seus not recognize your phone because you have a rooted and custom firmware in your x10 and xrecovery is not working because you did a reset and then you delete some files from your phone, you can reinstall it with the x10flashtool or to make a complete restore firmware whit the same x10flashtool
Click to expand...
Click to collapse
one more thing....i checked the device manager se drivers r working f9.....when i connect phone via usb cable the green light automatically turns on....even b4 i press back key
iMatth3w said:
Take the phone with the warranty for repairing.
Click to expand...
Click to collapse
I bought it from ebay ...no warrenty... think thats stupid :/
rumanbsl said:
nope, phone is not connecting in flash mood..i pulled of the battery and did as u said,,nothings working ......
Click to expand...
Click to collapse
Did you wait for at least 30 seconds before putting battery inside phone (to make sure clearing all memories? And sure you hold back button before, during and after?
Otherwise, what does happen if you press and hold volume button before turning on the phone (and keep volume button hold)?
rumanbsl said:
one more thing....i checked the device manager se drivers r working f9.....when i connect phone via usb cable the green light automatically turns on....even b4 i press back key
Click to expand...
Click to collapse
Well your usb is definitly working then as its glowin green?..
Are you sure you are doing it all right? It happened the same to me, and it ended I was pressing the wrong buttom (I knew which one was the correct one, but was blind cause I was scared that Ive broke it totally), a day later I noticed it and I was able to flash my phone.
However, read a guide and follow it step by step, reinstall everything and start from beginning maybe?
Or use the repair function with PC Companion
Hi! I had the same problem!
1. Search and download from this forum Flashtool 0.2.6
2. Install it.
3. Download from this forum one generic ROM (for exemple X10i_2.1.A.435_GLOBAL-GGL GENERIC 1232-9897 )
4. Put the file in directory Flashtool/firmware
5. Launch X10flashtool.exe
6. DO NOT PUT THE USB CABLE IN THE PHONE
7.From option "flash select the desired ROM
8. Wait the program to begin(a picture will appear)
9. Pressing the back button, insert the usb cable.
10. Wait the flashing to begin and release the back button.
Follow instructions and WAIT around 5 minutes until flashing will complete
11. Send me two words if it helps you! Success!
ohm74 said:
Did you wait for at least 30 seconds before putting battery inside phone (to make sure clearing all memories? And sure you hold back button before, during and after?
Otherwise, what does happen if you press and hold volume button before turning on the phone (and keep volume button hold)?
Click to expand...
Click to collapse
I've did everything as u told.....no luck ! guess its the time to go to repair center...btw a guy from help center told me about software tampered,,!!out of luck
if your x10i brick (SE Logo) and can't reboot can't access xrec and can't access flash mode (for flash generic rom)
i have a solution..
1. connect the phone to PC (USB)
2. open superOneClick v1.55 and click shell root icon
3. open FlashTool 0.2.9.1 and click Ask Root Perms
4. click menu advanced --> clean --> clear cache
5. click xrecovery icon
6. click menu advanced --> Xrecovery--> Reboot into Recovery
7. look you phone.. bingo.. u can access Xrecovery and then just install u favorit custom rom n reboot..
8. now u phone normaly n u can access flash mode to flash generic rom..
and.. sory my english is bad hehe...
jakadewantara said:
if your x10i brick (SE Logo) and can't reboot can't access xrec and can't access flash mode (for flash generic rom)
i have a solution..
1. connect the phone to PC (USB)
2. open superOneClick v1.55 and click shell root icon
3. open FlashTool 0.2.9.1 and click Ask Root Perms
4. click menu advanced --> clean --> clear cache
5. click xrecovery icon
6. click menu advanced --> Xrecovery--> Reboot into Recovery
7. look you phone.. bingo.. u can access Xrecovery and then just install u favorit custom rom n reboot..
8. now u phone normaly n u can access flash mode to flash generic rom..
and.. sory my english is bad hehe...
Click to expand...
Click to collapse
sorry i`m spanish and my english is very bad.
My problem: my x10 cant acces flash mode because pc dont detect the phone. Dont charge, etc... the brick block charge dock, mini usb...any solution please.
try thread from DoomLORD : [DEV][How-To] Get Back to Stock Even With Broken / Damaged USB Port in http://forum.xda-developers.com/showthread.php?t=1054818
tarzerixx said:
sorry i`m spanish and my english is very bad.
My problem: my x10 cant acces flash mode because pc dont detect the phone. Dont charge, etc... the brick block charge dock, mini usb...any solution please.
Click to expand...
Click to collapse
Likely the USB port is dead and you have to send it in for repair.
I used flashtool 3.0, pretended I was gonna flash 2.1 onto it and wella it worked. Your idea fixed my phone Dude. Thanks for the help.
pccobra said:
I used flashtool 3.0, pretended I was gonna flash 2.1 onto it and wella it worked. Your idea fixed my phone Dude. Thanks for the help.
Click to expand...
Click to collapse
Please mention the steps, or link, when i press on shell root(in superone click) it keeps on waiting for device. (flashtool never enables ask for root).
NOTE: It happened when I was trying update my ROM Wolfbreak , I did factory rest and all other resets available on xRec . (xcluding sd card format) then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen. please give me some thoughts to make it in working mode again
Thanks
RedAxe said:
Please mention the steps, or link, when i press on shell root(in superone click) it keeps on waiting for device. (flashtool never enables ask for root).
NOTE: It happened when I was trying update my ROM Wolfbreak , I did factory rest and all other resets available on xRec . (xcluding sd card format) then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen. please give me some thoughts to make it in working mode again
Thanks
Click to expand...
Click to collapse
Hapenned the same to me...
I try to follow the steps, but i can't pass step 4 (it's unavaiable the "clean cache" bottom...)
Please help...
Restore original firmware with SEUS
RedAxe said:
...then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen...
Click to expand...
Click to collapse
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
do u have trick for my problem here forum.xda-developers.com/showthread.php?t=1388476
my x10 just vibrate once and stack on blank screen.
Sent from my X10i using Tapatalk
When I use SEUS It keep saying "You have the newest software available"
I tried the hard reset and all. The phone now just won't start at all
Hi,
i got the same problem what you describe ive stuck at the SE logo and cant get into recovery and i cant use flashtool. i tried to do what you say in the first post, but when i press the shell root button, it says "wait for device" then its not responding, and i cant moce on to the next step... what should i do now?
Ketoth said:
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
Click to expand...
Click to collapse
u totally saved me =D
X10 mini revived!
Hi,
The procedure described above works fine until you've the phone recognized by the computer.
Here's how It has finally been recognized:
1) Completely switch off the phone (Do not leave it with SE logo).
-You can do the either by removing the battery connector (be cautious) under a rubber on the left(not above) of the camera lens.
-OR when the USB is plugged in,
(1.1) press center + back + power button until power off,
(1.2) then release center and power button AND KEEP back button down(about 2-5 seconds) until green led lights on. remark:LED will stay green until you unplug USB or phone switches on.
(1.3) Unplug USB.
Your phone should be OFF now. SE logo doesn't appear anymore (Wait 30s to be sure)
2) Unplug the USB cable from computer and plug it in another USB port of the PC.
3) At this time, if you plug USB on your X10 mini, it should be recognized as a SEMC device (It has worked for me).
-Success? Go step 4
-Failure, retry (from step 2 should be enough) with another USB port. If you've tryied all ports already, I've no idea.
4) If step 3 is successful, unplug USB.
5) Start SEUS (update service program from SE), choose you phone, follow the instructions on screen. Remark: Even if it says that you've got the last version, there is an "Install" button available on the bottom right corner. Click it!
Hope it'll help.
deBelch.
PS: Many thanks the whole forum for the help provided.
hello guys..my se xperia x10 mini pro stuck on the SE logo..and i tried to press power+ home button but it din't change anything.It also give 0.3sec led green flash while pressing the power and the menu button.can anyone plz help me with this..???
cruzstar said:
hello guys..my se xperia x10 mini pro stuck on the SE logo..and i tried to press power+ home button but it din't change anything.It also give 0.3sec led green flash while pressing the power and the menu button.can anyone plz help me with this..???
Click to expand...
Click to collapse
Update phone using SEUS....
Just google SUES
Definitely it will work....
Sent from my X10i using xda premium
yea i have use the SEUS..by pressing the back button..but it dont work..plz help me
Dear sir i already done that procedures but no use in seus shown u already updater software. plz help me
Cannot unbrick xperia mini E10i
Ketoth said:
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
Click to expand...
Click to collapse
Hello Guys,
I need your urgent help.
I cannot restore phone with SEUS or Companion. It says I already have the soft.
Getting fatal errors in Flashtool, I am stuck with SE logo and bootloader relocked.
I have the stock kernel but CM7 ROM.
Do you have any other ideas?
Tanks a lot!
deBelch said:
Hi,
The procedure described above works fine until you've the phone recognized by the computer.
Here's how It has finally been recognized:
1) Completely switch off the phone (Do not leave it with SE logo).
-You can do the either by removing the battery connector (be cautious) under a rubber on the left(not above) of the camera lens.
-OR when the USB is plugged in,
(1.1) press center + back + power button until power off,
(1.2) then release center and power button AND KEEP back button down(about 2-5 seconds) until green led lights on. remark:LED will stay green until you unplug USB or phone switches on.
(1.3) Unplug USB.
Your phone should be OFF now. SE logo doesn't appear anymore (Wait 30s to be sure)
2) Unplug the USB cable from computer and plug it in another USB port of the PC.
3) At this time, if you plug USB on your X10 mini, it should be recognized as a SEMC device (It has worked for me).
-Success? Go step 4
-Failure, retry (from step 2 should be enough) with another USB port. If you've tryied all ports already, I've no idea.
4) If step 3 is successful, unplug USB.
5) Start SEUS (update service program from SE), choose you phone, follow the instructions on screen. Remark: Even if it says that you've got the last version, there is an "Install" button available on the bottom right corner. Click it!
Hope it'll help.
deBelch.
PS: Many thanks the whole forum for the help provided.
Click to expand...
Click to collapse
nope...didnt work...there is NO Install beneath...wonder why? is it i am using the latest SEUS?
greetings. please i followed your steps to unbricked my device but my x10 cant boot into flash-mode. whenever i try to connect it via flash-tool. the green light comes on but in some few seconds it boot automatically. and when i try to flash anything it boot automatically. please help me
---------- Post added at 12:21 AM ---------- Previous post was at 12:16 AM ----------
greetings. please i followed your steps to unbricked my device but my x10 cant boot into flash-mode. whenever i try to connect it via flash-tool. the green light comes on but in some few minutes it boot automatically. and when i try to flash anything it boot automatically. please help me
Help me ppl ! I screwed up big time !!
I originally got X10 mini with Android 2.1 and relatively old firmware ...anyway I rooted my phone, took the backup and then Flashed a CWM Recovery on it !
Factory WIPED all the data for the new ROM ......
Then I was about to Flash this CM 7.1 ROM when all of a sudden it displayed the message that it wont work wihout the Latest Firmware .... so from there on I had no choice but to Restore my Backup and go back to a working OS, so I could easily proceed with Firmware update ...... but that never happened !!!
The Backup couldnt be recovered ...it failed for i dont know what reason ....ever since then the device never worked beyond the WHITE Sony Ericsson LOGO !!! Im stucked ..... even the CWM Recovery isnt working now !!
I'm stucked !! I've been looking for a solution for almost 3 days now .... but had no luck !!! dont know what to do from here on!! KINDLY HELP !! plzz plzz plzzz !! I desperately need to fix this !! the device even aint mine !!!
restore to stock by using sony ericsson update service
First, don't panic
And you have to notice and make this a lesson; if CWM said that your baseband is incompatible, it means, CWM is not flashing anything to your phone, yet.. So you only have to restart the phone, instead of recovering your CWM backup, and you'll be back to your default OS
Second, now find a tool named FlashTool, and also find a 2.1 stock firmware.. now proceed to flash with USB cable, you'll find the instruction together with the tool
Third, you'll be OK, trust me
first of all moedjs man !! Thx for sympathy n giving me courage !!
but could you kindly confirm that FlashTool would still work even If I'm unable to mount USB anywhere !! coz USB would charge phone but since I'm stuck on Sony Ericsson Logo and cant go beyond that point I'm unable to update my Firmware via PC Companion tool by Sony Ericsson tooo !!!
Thats the main reason I was panicking mate !! Kindly Kindly confirm that for me !! n I'm already liking your positive attitude ..so I do trust ya !! THX again !!
i don't understand why you can't use official seus? afaik it doesn't need anything beyond the se logo. power off phone, run seus on the pc, plug the cable while pressing the back key, etc; right?
dr.norton said:
i don't understand why you can't use official seus? afaik it doesn't need anything beyond the se logo. power off phone, run seus on the pc, plug the cable while pressing the back key, etc; right?
Click to expand...
Click to collapse
Sir I've been through that .... for some reason it didnt work for me beyond "plug the cable while pressing the back key" STEP !! i dont know why !! i didnt have any effect watsoever, therefore I couldnt proceed with the 3rd STEP of Updating it ! =(
and is there anyway to Remove the battery !! coz once I use Home+Power Key combo it restarts device ...... is there any other combo to power off the phone, so I can atleast save battery !! anyway m also givin FLASHTOOL a try !!
can't power off? well, try these steps:
start seus on pc
connect phone and pc with usb cable
press both middle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
dr.norton said:
can't power off? well, try these steps:
start seus on pc
connect phone and pc with usb cable
press both middle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
Man I just tried turning on my device for the first time today !! Battery was discharged i guessed so Initially I got Red blinking LED light .... now even that its stable on Green .... !! my device isn't turning on !! not even showing that white Sony Ericsson logo now ! i dont know whats happening here !!
I'm trying to be calm but stuff like that keeps happening to me !! Kindly guide me with that !! its still green I hold power button n yet its showing no sign of turning on ! =(((
do you see charging battery in your screen? have you waited enough to boot it again and try the steps above?
still, if you need to disconnect the battery, here is a disassembling guide: http://goo.gl/jDd6q
dr.norton said:
do you see charging battery in your screen? have you waited enough to boot it again and try the steps above?
still, if you need to disconnect the battery, here is a disassembling guide: http://goo.gl/jDd6q
Click to expand...
Click to collapse
Wow thanks for that Dis-Assembling guide ..... !! I'll ultimately have to try this if everything else fails ....
well I never saw Battery charging on screen !! i think not even when it was working fine !!
I think i'll give it some more time with charging !! coz it just showed me that SE logo again .... but when I tried to restart it .... the screen didnt turn back on !!!
also when SE Logo appears it appears automatically ......dont have to turn on the device ... and then also green LED light turns off ..... Im not sure whether its still charging at that time or not !! I think NOT ! this is kinda dodgy ! what do you reckon ?
no led light, no charge, i think. have you tried triple keys way again? it's kind of tricky, do it carefully.
Yeah I did !! I pressed HOME+Back at the same time and then had to Hold the Home button to turn the screen off ! then I repeatedly kept pressing the BACK button!
actually from there on it started blinking that RED Led light again .... ! I think its still needs more charging .... but then again If it charges enough to power the screen on automatically ..... the Green LED disappears .... so M kinda stuck in the loop here !
Oh God Help me !!
devilzeye793 said:
I pressed HOME+Back at the same time and then had to Hold the Home button to turn the screen off ! then I repeatedly kept pressing the BACK button!
Click to expand...
Click to collapse
it sounds not right pal
but by:
Middle Key : u meant HOME
Right Key : u meant BACK
isn't it ??
devilzeye793 said:
but by:
Middle Key : u meant HOME
Right Key : u meant BACK
isn't it ??
Click to expand...
Click to collapse
yes, but there's power key too. and there's no repeating but holding the back key constantly.
dr.norton said:
yes, but there's power key too. and there's no repeating but holding the back key constantly.
Click to expand...
Click to collapse
I did try this method ....it has no effect ..!! it keeps on waking screen on !! and sony ericsson logo doesnt go away !!
NEITHER is FLASHTOOL working for me !! =(
a. Unplug your USB cable from PC
b. Power off your phone
c. Press back button and keep your finger on button
d. Plug USB cable to PC
e. Check if the green LED appear
f. On popup message press "OK" button
That OK Button never appears for me !! I dont knw wat to do next
Kindly help !!!!
i think flashtool needs a working system.
can you power off your phone or not? if able to do so, seus should work.
so, you have just one option if you can't start recovery: using seus.
and you've two options to start seus: the standart way, or the triple buttons way.
if you can enter recovery, you can try to wipe everything and flash a rom.
these are all i can say about it. hope you can solve it.
dr.norton said:
i think flashtool needs a working system.
can you power off your phone or not? if able to do so, seus should work.
so, you have just one option if you can't start recovery: using seus.
and you've two options to start seus: the standart way, or the triple buttons way.
if you can enter recovery, you can try to wipe everything and flash a rom.
these are all i can say about it. hope you can solve it.
Click to expand...
Click to collapse
When charged enough there's no way to turn the device off ! I've tried both HOME+POWER & HOME+BACK then POWER (holding the back Key towards the end) button none of them actually works ! The Screen keeps powering back on, showing up that Sony Ericsson Logo !
Could it be USB Bricked or something ? (Apparently, since I cant access recovery I cant mount the device)
Try:
- turn off phone
- wait for 1 minute, phone still off
- connect to usb with flashtool
I have almost the same problem, my phone have been breaked several times but every time i had access to xrec or internet to solve problem.But this time when phone dischared for first time n I wanted to start it again I found that it's not gonna boot! Stuck on SE text logo... (I flashed CM7)
now it's charged ( although the screen was on, showing SE) n I have flasher n a rom.
but when i start to flash after showing "start Falshing" on screen (CMD) some seconds pass n CMD shows "write failed" n other things...
When i connect my phone to pc red LED shows itself for some seconds n after it disconnects itself while i'm pressing the back key...
And two questions:
1. Does it matter what the name of the ROM file -in firmware folder- is?...
2. I have to ftf files. on is about 108 MB n the other one 280 MB. Eachone can be a ROM?(I have tested Flasher with both of them.)
tnx
hey all, i have a small brick with my x10 mini
currently the phone it stuck at the sony ericsson screen
and when i connect my phone with SEUS, it just tells me to mount the phone but since its stuck on the sony ericsson screen, i can't do that
what do i have to do to restore the stock 2.1 onto my x10 mini?
thanks~
Listen tu me...
Do you have installed flashtool, if you have then you must go to the Drivers folder and install the gg-setuup... something like that is called... Install it... then put the phone into flash mode with two buttons... middle button below the keyboard where the three keys... button to turn on the cell phone... These two buttons are pressed and keeps... pres the thanks button if i helped you...
well the problem i'm having is that the phone will not turn off since its stuck at that screen
so i can't boot it into flashmode @[email protected]'
lil-devil said:
well the problem i'm having is that the phone will not turn off since its stuck at that screen
so i can't boot it into flashmode @[email protected]'
Click to expand...
Click to collapse
Not sure tho.. Connect your phone to pc.. Then give adb reboot command ( considering you know what ia adb ) your phone will reboot ( as u mini.,i guess u cannot pull out ur phone battery )
Sent from my U20i using xda premium
no i can't pull the battery out, or i would of already >.<;
and i can't give it adb commands because during the bootup screen the adb function is not enabled yet otherwise i could use the flashtool to do it =/
Listen tu me...
put the phone into flash mode with two buttons... middle button below the keyboard where the three keys... button to turn on the cell phone... These two buttons are pressed and keeps... pres the thanks button if i helped you... I had the same problem... I solve it so I put cell phone in flash mode with two buttons that I have mentioned...
i took the phone a part slightly so i was able to access the battery to disconnect it
and i tried to boot the phone into recovery or flashboot and i wasn't able to
i tried power + down volume key
and power + home key
wasn't able to get in
does anyone have any idea?
Thanks~
I'm with the same problem, but the recovery nor flashmode is accessible :/
follow this step..
http://forum.xda-developers.com/showthread.php?t=981935