Related
Hi, I have a HTC Pro for sprint, I love everything about it except the battery cover and volume buttons.
The cover creaks, and makes a ton of sound if I try to use the keyboard, one corner is loose, and I believe thats where the sound comes from.
Also the volume keys are hard to use and they sound more like creaking plastic, I cant even tell when it is actually clicking.
Anyone else have this problem? Mine has been like this since day 1.
Any fixes?
I was about to say "Perhaps you have a defective machine, as I also have a Touch Pro from Sprint and have not really noticed this problem" and then I picked it up... top corner as in the back cover right behind about where "Sprint" is printed on the front? Mine actually makes creaky noises there, too... with a bit of push.
I honestly don't notice the noises when I am typing with it, simply because I'm used to keyboards clicking, and noises around me, but I do see what you're saying. I have no fixes to offer, since it seems to be manufacturing rather than a joint or something that could do well with a little dab of WD-40 or something. If the noise takes over my mind, though, you are totally to blame.
Just got mine today. It's very pretty. My first note after only a few hours of usage is the top panel/screen slides a bit to easy, the mogul was a bit more tight...
With some well placed paper, I took small pieces and folded it once, on the corners you can make the cover fit better. This has silenced the creak people are talking about.
Considering the backis a peice of plastic that flexes to lock in and come off,
I don't mind the creaking. I'd prefer this than over a heavy piece of steel
with screws holding it in. The phone is heavy enough as it is.
Sure the quality control isnt' fantastic. The buttons on the face are a little raised up.. but not enough for me to be picky about it. The phones nice, I like it, and i'm happy it's pretty darn good.
Mine creeks too...and the power/volume hard keys dont give good feedback and have minimal travel. I feel as though the power button will break soon, especially since it's used so much to wake the phone. The overal construction is much more beautiful than the mogul, but aside from the keyboard buttons, the construction feels more flimsy, and the slider not as smooth as the mogul.
The touch screen seems to be less sensitive too.
Oh well...it's only a very expensive phone...
My cover creeked pretty bad. I cut a business card to fit and put it under the cover. Problem solved.
i fixed this by putting blue painters tape in layers and cutting to the right size and adding one layer at a time and then putting the cover back on then checking the noise. i reapeated this till it no longer creaked. this is not my fix but posted by someone at ppcgeeks and i think i was linked from there too. but the painters tape has a smooth surface on the non sticky side and it helps the battery cover slip on easily and is easily removed if you need to. hope this helps. oh yea the area around the micro sd slot is the main creaking area on mine and i have heard others say the same. it took 3-4 layers there.
tommy11481 said:
i fixed this by putting blue painters tape in layers and cutting to the right size and adding one layer at a time and then putting the cover back on then checking the noise. i reapeated this till it no longer creaked. this is not my fix but posted by someone at ppcgeeks and i think i was linked from there too. but the painters tape has a smooth surface on the non sticky side and it helps the battery cover slip on easily and is easily removed if you need to. hope this helps. oh yea the area around the micro sd slot is the main creaking area on mine and i have heard others say the same. it took 3-4 layers there.
Click to expand...
Click to collapse
I used some thin strip electrical tape 2 layers on the right side next to the camera. "QUITE NOW"
I think its individual defectiveness. My phone creaks only if I put my ear 1 inch away from it when i press the Sprint logo, extremely unnoticeable. It feels much more solid than my last phone, HTC(PPC)6700, the side buttons are all solid and secure and respond well. No tape needed. If this happened to my phone I'd take it back and demand a new one as it retails for 550USD and that sort of defectiveness is unnacceptable. Although my 6700 retailed for 600USD and was much cheaper.
Mine also has a little creek. There isn't much i dislike about this phone besides the lack of working FM at the moment, and most importantly, the performance of 3d applications/games,videos etc.
I'll try the tape thing tonight.
Wow I don't know why I didn't think about putting something behind the cover. I was complaining that mine feels cheap, but I just threw a few post its back there and now it's nice a firm! thanks!
I ordered my first touch pro over the phone, and it felt SO cheap with all of the "symptoms" of what everyone has been saying, but for a different reason I had to exchange it, and the one they gave me at the store feels SO much sturdier.. I am glad I exchanged..
This is my first review, so I hope it doesn't suck.
Both my wife and I have the Tilt 2. I decided to go with InvisibleShield while she wanted a case. After looking at all the comments here about cases not fitting, I decided to go with 2 different ones from Amazon. One fit horribly, so i wont even mention it.
She is using the Tilt2 Praetorian Slip and she loves it. Installation was a little tough as the fit is pretty precise. I suggest installing the top (screen) side first and then the bottom (keyboard). Install both with the KB extended. I have attached pics of the fit.
The only complaint I have (she thinks of it as a feature) is that the cover makes it a little more difficult to slide out the keyboard. She like it because it used to slide open in her purse (mostly because of the fact that she keeps it in an inside pocket of her purse which causes it to hit just right against crap she has in another pocket). Overall, this is a pretty nice cover. I am sure you can get it cheaper than amazon, but I had gift certificates to spend
Hope this helps!
Thanks for the review! I bought the same case a few months ago, although it was advertised as for the Verizon Touch Pro 2. I was unaware they made one for the Tilt 2. Now I won't have to worry about it falling off randomly!
thsi case probably wouldnt work with invisible shield on too huh
Doinshots said:
This is my first review, so I hope it doesn't suck.
Both my wife and I have the Tilt 2. I decided to go with InvisibleShield while she wanted a case. After looking at all the comments here about cases not fitting, I decided to go with 2 different ones from Amazon. One fit horribly, so i wont even mention it.
She is using the Tilt2 Praetorian Slip and she loves it. Installation was a little tough as the fit is pretty precise. I suggest installing the top (screen) side first and then the bottom (keyboard). Install both with the KB extended. I have attached pics of the fit.
The only complaint I have (she thinks of it as a feature) is that the cover makes it a little more difficult to slide out the keyboard. She like it because it used to slide open in her purse (mostly because of the fact that she keeps it in an inside pocket of her purse which causes it to hit just right against crap she has in another pocket). Overall, this is a pretty nice cover. I am sure you can get it cheaper than amazon, but I had gift certificates to spend
Hope this helps!
Click to expand...
Click to collapse
Neat.. glad yours fit. I ordered one for the Tilt2 from Amazon as well, and Boxwave sent one labeled 'Touch Pro 2'. I see yours doesn't have a cutout area for the PTT button either, do you have issues with that? My praetorian case would almost always trigger the PTT button whenever I handled the phone.
The top/screen portion of my Praetorian didn't fit right and opening and closing the top was almost impossible - even ended up ripping off the protective plastic along one side of the keyboard. (the protective plastic that is designed to be there, not the temporary stuff it whipped with) I can see just by looking at your pictures that your screen portion fits waay better than mine did.
When I contacted Boxwave about the issues, no questions asked and they sent a postage paid label for the return. I'd love to try this case again, as I did like the feel of it, but nervous about another no-fit. I went with BodyGuardz instead.. not sure I'm happy with those..
Thanks,
I´ll include it on the main thread
http://forum.xda-developers.com/showthread.php?t=524059
JJHiemenz said:
Neat.. glad yours fit. I ordered one for the Tilt2 from Amazon as well, and Boxwave sent one labeled 'Touch Pro 2'. I see yours doesn't have a cutout area for the PTT button either, do you have issues with that? My praetorian case would almost always trigger the PTT button whenever I handled the phone.
The top/screen portion of my Praetorian didn't fit right and opening and closing the top was almost impossible - even ended up ripping off the protective plastic along one side of the keyboard. (the protective plastic that is designed to be there, not the temporary stuff it whipped with) I can see just by looking at your pictures that your screen portion fits waay better than mine did.
When I contacted Boxwave about the issues, no questions asked and they sent a postage paid label for the return. I'd love to try this case again, as I did like the feel of it, but nervous about another no-fit. I went with BodyGuardz instead.. not sure I'm happy with those..
Click to expand...
Click to collapse
Man, sorry you had so many issues. The PTT button is indeed covered, but she has had no issues with it at all (hers is remapped to toggle bluetooth on and off). The fit on the screen portion is *very* tight. Took some effort to get it installed properly.
Also, mine definitely said "Tilt 2" on the packaging.
It is disappointing that it covers the PTT button. I assume your wife has abandoned that function (easily switching BT on/off)?
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
sleze said:
It is disappointing that it covers the PTT button. I assume your wife has abandoned that function (easily switching BT on/off)?
Click to expand...
Click to collapse
Nope, the PTT button still works perfectly under the cover. Does not get accidentally pressed and is responsive when you push it.
azwildcat98 said:
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
Click to expand...
Click to collapse
Sounds like skinning/shielding your phone with GadgetShieldz might be the way to go. The GadgetShieldz does take a little time to install but it works. The protective film on the screen is easy to install and bubble free. It makes the phone non-slippery. It would not protect the phone like a case but it does prevent scratches. When installed, it adds very little weight and dimension to the phone.
Actually, there are other protective films/shields but I only have experience with GadgetShieldZ. It might work for you.
Boxwave Praetorian Crystal Slip for Tilt 2
orb3000 said:
Thanks,
I´ll include it on the main thread
http://forum.xda-developers.com/showthread.php?t=524059
Click to expand...
Click to collapse
Just to report on this, I got one of these in the mail yesterday. So far I love it. It wasn't terribly difficult to get on. It fits very well too. My only real complaint is that it doesn't accommodate the PTT button that the Tilt 2 has right next to the volume buttons. It's not a big issue since I don't use PTT and the case doesn't prohibit using the key anyway.
Just be careful and make sure you order the one that specifically says it's for the Tilt 2. They make other models. I know they have the Praetorian on eBay but to be safe I opted to get mine directly from Boxwave. I got what I ordered too and could have used they're return policy if I needed.
Oh...I'll be happy to post pics if anyone wants but I think someone already put some up of this one a Tilt2.
azwildcat98 said:
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
Click to expand...
Click to collapse
I wish I'd seen your post sooner! Home Depot and Lowe's does indeed have something like that. I'm sure lots of hardware stores do. It's called Plasti-Dip. I have a can right here You can buy it as spray-on or dip/brush-on applications. I use it on mountain bike parts and tools for extra grip. I'm not positive how well it will stick to a slick plastic surface but it is an option.
BluEyedTiger said:
Just to report on this, I got one of these in the mail yesterday. So far I love it. It wasn't terribly difficult to get on. It fits very well too. My only real complaint is that it doesn't accommodate the PTT button that the Tilt 2 has right next to the volume buttons. It's not a big issue since I don't use PTT and the case doesn't prohibit using the key anyway.
Just be careful and make sure you order the one that specifically says it's for the Tilt 2. They make other models. I know they have the Praetorian on eBay but to be safe I opted to get mine directly from Boxwave. I got what I ordered too and could have used they're return policy if I needed.
Oh...I'll be happy to post pics if anyone wants but I think someone already put some up of this one a Tilt2.
Click to expand...
Click to collapse
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
BehindTheLight said:
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
Click to expand...
Click to collapse
I ordered one from BoxWave and I think I'm still going to shop around for something else. It seems like the Tilt2 has less options than the other variations of the Rhodium so people may just be settling for this due to "Slim Pickin's."
I like the way the gel gives more texture and grip to the phone, but I still feel uneasy because it's definitely not a snug fit. The part that covers the screen section of the phone is very flimsy and after you get it on, you want to keep checking it to make sure that it is attached; it feels like it can easily slip off at any time. This is specifically evident when you slide your screen up and tilt it. Tap the top right, or the middle section that really has no grip around the phone, and it might just pop off...
I still have it on my phone because it is the lesser of two evils, have something vs. not having something, but are there any other options for the Tilt2?
BehindTheLight said:
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
Click to expand...
Click to collapse
It's held up quiet nice...even with as much flashing I do (have to remove the bottom piece every time). I've figured out a great way to put it back on that's really fast and easy. Some people say it's difficult to get on. I think the top piece is the hard part but I've taken it off a few times and have no issues there either. It still fits good. If I remember, next time I take it off I'll shoot some pics of how I put it on and upload them.
Learic said:
I ordered one from BoxWave and I think I'm still going to shop around for something else. It seems like the Tilt2 has less options than the other variations of the Rhodium so people may just be settling for this due to "Slim Pickin's."
I like the way the gel gives more texture and grip to the phone, but I still feel uneasy because it's definitely not a snug fit. The part that covers the screen section of the phone is very flimsy and after you get it on, you want to keep checking it to make sure that it is attached; it feels like it can easily slip off at any time. This is specifically evident when you slide your screen up and tilt it. Tap the top right, or the middle section that really has no grip around the phone, and it might just pop off...
I still have it on my phone because it is the lesser of two evils, have something vs. not having something, but are there any other options for the Tilt2?
Click to expand...
Click to collapse
I haven't really had any trouble with mine popping off. It took a bit to get the top on right and it was a pretty snug fit too. Getting the corner edges all the way tucked under was the hardest part. I'm guessing it's a manufacturing thing. Some say it's a tight fit and other say it's loose. I will agree that the sides on the top piece are flimsy because they're not attached the the phone but if they were it would probably make matters worse by either rubbing against the bottom piece or creating too big of a gap between the two parts of the phone.
I agree there aren't many options for the Tilt 2 and I hate to say it but there probably won't be.
BluEyedTiger said:
I haven't really had any trouble with mine popping off. It took a bit to get the top on right and it was a pretty snug fit too. Getting the corner edges all the way tucked under was the hardest part. I'm guessing it's a manufacturing thing. Some say it's a tight fit and other say it's loose. I will agree that the sides on the top piece are flimsy because they're not attached the the phone but if they were it would probably make matters worse by either rubbing against the bottom piece or creating too big of a gap between the two parts of the phone.
I agree there aren't many options for the Tilt 2 and I hate to say it but there probably won't be.
Click to expand...
Click to collapse
If yours is a snug fit, I wonder if we received the same thing! Did you order from BoxWave? I have a little plastic tool that I used to get the corners onto the top half quickly which was actually made to fit into the creavice of a HTC Dash phone to pop the clips and take the phone apart. It works great and I can see the little flaps around the corner so you can tell the corners of the phone are between the gel lips.. It's still too easy to come off though..
Even though my receipt says "Praetorian Crystal Slip, HTC Tilt2, Smoke Grey - SKU: bw-268-3729-2808", it also says "ITEM: HTC TOUCH PRO2." The Box also has a white sticker in the top right that says "Praetorian Crystal Slip - TOUCH PRO2."
Do you remember if yours said the same? Maybe they somehow shipped me the wrong one?
Learic said:
If yours is a snug fit, I wonder if we received the same thing! Did you order from BoxWave? I have a little plastic tool that I used to get the corners onto the top half quickly which was actually made to fit into the creavice of a HTC Dash phone to pop the clips and take the phone apart. It works great and I can see the little flaps around the corner so you can tell the corners of the phone are between the gel lips.. It's still too easy to come off though..
Even though my receipt says "Praetorian Crystal Slip, HTC Tilt2, Smoke Grey - SKU: bw-268-3729-2808", it also says "ITEM: HTC TOUCH PRO2." The Box also has a white sticker in the top right that says "Praetorian Crystal Slip - TOUCH PRO2."
Do you remember if yours said the same? Maybe they somehow shipped me the wrong one?
Click to expand...
Click to collapse
Yeah I got mine directly from boxwave. They have like 3 different models of that slip. Most of the adds I saw on Amazon and eBay claimed it would fit on 3 or 4 different TP2 models which I knew it wouldn't. I emailed boxwave about the pics in their online catalog because it didn't look like a Tilt 2 to me and they admitted it wasn't. They said they didn't have one for the pics. Which made sense I mean why spend that much just to get pics but they promised it would fit so I figured what the hell. The hard covers kinda suck.
Thanks for the replies, I guess I will go ahead and order it and see what happens.
I just got the unbranded version of this case off ebay (the seller's id was e-story).
It's not too bad on my unbranded TP2. It's slightly more difficult to slide out the keyboard, and when the screen is fully tilted, the top row of keys are slightly obscured, but nothing too major in my opinion.
I like that the case improves the grip of the phone, but I'm also rather concerned that the case will eventually melt under hotter conditions since the material feels rather gummy.
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
Does anyone have experience with this case? I know it covers the mic (I plan to drill a little hole).
I just received mine today and I must say I'm very impressed by the quality of the mold they used. Meterial seems top notch. Love this case so far, they also included the new screen protector which is a plus. Ill get pictures up ASAP. I would definetly recommend this case to anyone with an s2.
Sent from my SAMSUNG-SGH-I777 using xda premium
Pictures would be great! I also have a white one on the way, hopefully as I placed an order over the weekend. I intended on modding the thing to get rid/fill in the antenna hole if I ever find the time, too (or find out if it really bothers me that much).
Ok, whats the deal with the corner cutout? I've seen this on several different cases. Does the international version have some sort of pullout antenna?
Case looks nice and classy but for what they are charging they should be offering a case that's specific to the AT&T model.
I recall reading that the corner cutouts are originally for Korean model phones. The antenna was in that area for those phones.
I really like it. It's a nice mix of hard and soft materials. It's flexible, which is nice because it makes removing the case fairly easy (for those of you who want to access the phone's back cover to hot swap batteries).
For the most part, the case feels pretty smooth, which makes getting it out of the pocket an easy process (I previously used the casemate pop case and the rubber sides made it fairly annoying to pull the phone out of the pocket). The case definitely adds more grip to the phone, but overall, it still is a little bit on the slippery side. On the continuum of "slippery vs. grippy" I'd say it's a pretty good balance, but I wouldn't mind it being a little more grippy.
Even though the case is made for the international GS2, it still fits well on the AT&T SG2. The noise-cancelling mic is covered by the case, but I have not had any problems as a result of this. However, you might come into problems if you are trying to use the phone in a noisy environment. I'm a little bothered by the corner cutout for the antennae (for the international SG2) since it really leaves that corner unprotected if the phone happened to fall right on that corner. Then again, i'm just going to take my chances that i'm not going to drop my phone on that exact corner.
The case still keeps the phone very thin and sleek. Also, the case has these tiny sparkle dots that show up on the back of the case, which give off a cool effect when reflecting light. Some may say, they make the case look a little feminine, but I personally don't think they do. In all honesty, you can't even really notice them unless you look close at the case and in the right lighting.
I got the yellow ultra capsule. I've heard one person say that these cases are prone for showing up finger smudges, but at least with my yellow one, finger smudges have not been a problem.
The case covers the volume and power keys. They are still pressable and work fine, but the buttons aren't as sensitive as they are without the case. However, this difference is really negligible for me. Overall, hardware buttons work fine.
I really liked the Body Glove Mirage cases that were made for the Samsung Captivate and the Infuse. In my opinion, this case is just as good as those cases.
can you guys post some pictures? want to see how much it adds to the thickness of the phone.
it does look good from their website though..
Sorry on the delay for the pictures guys, let me know if you need any certain perspectives on some more pictures.
djoutrages said:
Sorry on the delay for the pictures guys, let me know if you need any certain perspectives on some more pictures.
Click to expand...
Click to collapse
what does the unprotected corner look like with that case?
I got myself a prime last week, promptly ordered a keyboard because nobody had one in stock and I didn't feel like paying a $70 dollar premium on amazon to get it in the future anyway, and received the dock yesterday.
Electrically, the dock seems fine - all of the keys work, it charged normally, it's discharging normally, etc. - but it appears to have a physical deformity at the front of the unit. I took a picture of the unit to demonstrate... unfortunately, as some of you are no doubt aware, taking close-focus pictures of smallish things with an android camera is a little tough. Still, see attached image for the illustration. Note the gap between the rubber stopper and the fact that you can see the palm rest surface despite looking at the tray head on.
The question is, of course, "is this normal?" Does anyone else have a warped dock? It seems like the trackpad buttons don't quite click as easily as I think they should, but I don't have anything to compare it to. None of the local Best Buy stores have a dock on display, either.
[edit]I started this thread in the wrong forum and moved it here, then forgot to attach the file. Here's a link to an imgur-hosted copy:
http://i.imgur.com/Bn0la.jpg
nurrwick said:
I got myself a prime last week, promptly ordered a keyboard because nobody had one in stock and I didn't feel like paying a $70 dollar premium on amazon to get it in the future anyway, and received the dock yesterday.
Electrically, the dock seems fine - all of the keys work, it charged normally, it's discharging normally, etc. - but it appears to have a physical deformity at the front of the unit. I took a picture of the unit to demonstrate... unfortunately, as some of you are no doubt aware, taking close-focus pictures of smallish things with an android camera is a little tough. Still, see attached image for the illustration. Note the gap between the rubber stopper and the fact that you can see the palm rest surface despite looking at the tray head on.
The question is, of course, "is this normal?" Does anyone else have a warped dock? It seems like the trackpad buttons don't quite click as easily as I think they should, but I don't have anything to compare it to. None of the local Best Buy stores have a dock on display, either.
[edit]I started this thread in the wrong forum and moved it here, then forgot to attach the file. Here's a link to an imgur-hosted copy:
http://i.imgur.com/Bn0la.jpg
Click to expand...
Click to collapse
When mine is closed, the lid touches the rubber bumper on the keyboard which is what I would expect. Yours doesn't seem to close properly.
Thanks - that's what I suspected. It contacts the two rubber pads on the sides, so this poor thing is the victim of a god-knows-what. The box was completely undamaged so I guess someone sat on it at the factory.
Obviously anyone else that wants to weigh in is welcome to do so - on this topic, anyway, I don't recommend actually weighing in on the keyboard dock because I guess it will bend.
Yep, looks bent, as if it was laying on a soft rocking chair, couch or something undocked and someone sat on it. You could take your knee to the back of it with a hand on each side and try to bend it back You may end up with a creased unit afterward though... I'd send it back as a return and try to find one somewhere else.
My keyboard dock also came with a slight bend to it (from a UK Grey BC0KAS batch). I didn't notice it at first, but when I put the keyboard on a flat surface when closed, it wobbled. Towards the back the centre of the metal was coming into contact with the table, so the rubber feet were slightly raised.
I was able to gently apply pressure, using a soft cloth, to the metal around this area and correct this so it's not really noticeable now.
Also, when the tablet is docked, and closed, there is a slightly larger gap on the right side between the screen and keyboard than the left. It makes contact with all 3 rubber pads, but it's definitely there.
I'm still contemplating returning the whole lot to Comet, as I have 3 stuck pixels, and have been experiencing poor WiFi and some crashes.
Quality control definitely could have been better here.
SO! I went to another Best Buy that actually had docks in stock, did an exchange, and the second dock is bent as well. That said, the buttons on the trackpad actually click easily on this unit, so I think I'm going to keep it especially given how difficult it is to find anything with a TF-201 in its model number in stock.
It'd be interesting to see how many docks have warping or if it's supposed to be there. I guess it could be Asus' way of giving us space to fit our fingers in to open the unit...
Turns out mine was slightly bent too. I never would have noticed had it not been for this thread... Lol, anyway...mine was bent slightly in the middle. The middle rubber stopper didn't touch when cosed. It is really, really easy to bend this though...i just put pressure in the middle from behind and pushed slightly and the gap has disappeared.
I don't have the dock yet but this will be on my new dock QC checklist when I do get one. I'm not planning on getting one for a while so hopefully stuff like this will be ironed out by Asus and stocking levels are better. I'm thinking August (my birthday).