Related
Hi All,
I've been combing the forums for a number of days to see if I could find some help to a bluetooth pairing prob, but have yet to find what I'm looking for.
I have a new t-mobile mda that has been flashed to the latest 2.24 ROM (yes, i know it's a beta rom). I also have a Motorola H700. I can get the phone to see my laptop just fine, but it won't even detect the headset. I've looked around motorola's website, but it's less than helpful. I'm really hoping my new headset isn't DOA. It charges fine, but never enters pairing mode. I don't have another bluetooth enabled phone to test it with. I'm really hoping someone can offer some suggestions.
Thank so much!
im using an h700 i got from ebay for 35 bucks on my tmobile mda (2.17 qtek rom) and it pairs just fine. does your led stay in constant purple? that means it should be pairing. i dont see any reason why the phone can't detect the headset. are you sure the headset is entering pairing mode correctly? remember that after awhile itll exit pairing mode on its own. just a thought.
No, i have yet to get the thing into pairing mode (as i mentioned earlier ). Is there some way to force the headset to do so? Thanks!
Problem fixed. A little reg tweaking and the proper application of buttons & viola!, headest works fine.
care to share how u did that? cuz i have the same headset and i cant get it working either!
I have the thing basically working. I am also getting a Vox 710s to try as well.
My primary concern at this point is auto connect. I am a consultant and get in an out of the car a lot. So it is pointless if I have to click the stereo 6 times each time I get in. I need the thing to just work. I may return the deck if I can't get it too work.
So I need to find out where the failure is. Then I can pursue it with the manufacturer. Why can't this stuff just work?
So if I find a bluetooth headset that does auto connect to the phone do you think that is enough I can't got to pioneer and say the problem is your deck?
If the head set doesn't auto connect which I find hard to believe then I can work with jetware or cingular to see what is up. I am guessing it is the deck.
Thoughts
opps
phone is a cingular 8125 up to date roms running the latest Jetware.
another poster on crutchfeild says tmobile dash does autoconnect
does this narrow down the cause?
I spent over a month working with Pioneer and Jetware with an AVIC Z2 GPS unit with Pioneer's ND-BT1 adapter. In the end, I had to pull the Z2 and installed a Kenwood. Pioneer tech Support finally admitted that they suffer problems with nearly all PDA type phones, especially when they 'sleep'. Seems the connection is dropped nearly as fast as it is made and the devices won't stay connected. Mine dropped EVERY call when the backlight went out after 60 seconds of non-pda use. If i set time timer up to 5 minutes, it dropped the call when the PDA went to sleep. Leaving the PDA on all of the time of course drained the battery.
My wife now has the HTC Touch in her car with the AVIC Z2 and the ND-BT1, however, the problem isn't there. Pioneer has come out with a 'Service' upgrade program for the Z2 and the Touch uses a newer WM6 version. The two seem to be compatible.
thanks for the insight
Having just read the mk6000 review I don't feel so bad. I was wondering how well as system between your speakers and you deck would work.
That said I ordered an unlocked 710 (vox) to test out with wm6 and bt 2.
I am hoping this will work. Do you think I will still need Jetware?
xophere said:
Having just read the mk6000 review I don't feel so bad. I was wondering how well as system between your speakers and you deck would work.
That said I ordered an unlocked 710 (vox) to test out with wm6 and bt 2.
I am hoping this will work. Do you think I will still need Jetware?
Click to expand...
Click to collapse
Try it first without Jetware. It is now with at 30 day free trial and limited features but good enough to test once you get your new unit. If you find out that you need it, then register it.
I have had a Pioneer DEH-P9800BT for many months now, and I am getting sick of having to click 6 times to connect the phone. You would think that the stupid thing could perform the same thing when you turned on the car/stereo. I wish I could get a firmware update or something to fix it.
Replace your Pioneer with the one of the Sonys (MEX-5000BT if you need preouts, MEX-2500BT if you don't). I've been using the 5000 since January -- once I did the initial pairing, it connects every time both in handsfree & A2DP.
Hi everybody.
I've read at a couple of places that the Hero does not include any sim / phonebook remote access profiles which means I cannot sync my contacts with my Parrot CK3100 car kit.
I'm wondering if anyone knows why HTC would have removed this profile from their build when it was working perfectly as part of the standard cupcake build.
And also whether it is likely that HTC will reinstate this profile through future updates?
Speculation or definite answers welcome!
I'm also having this problem, as well as getting the phone to automatically reconnect when the phone and handset find eachother. Any body any ideas?
Ask Google why they STILL haven't added a full BT stack. It's the same for both the HTC Dream and HTC Magic aswell. UNLESS you wander the way of the rooters ofcourse. Then you will be able to use all those nifty little tools only the rooters can use.
I think that Google is a little bit slow on this subject tbh. But then again I have no idea of what they prioritize either. Maybe they have a BT stack but they feel it has some serious security issues? ONLY Google knows. Well... a couple of XDA's hardcore hackers might know too... isn't Haykuro around somewhere?
I have rooted my phone (yesterday). Can anyone suggest any tools that may help with this? Appreciate any help anyone cab give!
no problems here
hello i have just got my hero and im still learning the in's and outs of the device as i have come from a WM device, but have loads of success so far.
I have a in car bluetooth system and i have no problems with connecting, and searching my sim card for contacts.
The problem i do have though is that it will not read my phone contacts just the sim.
Its not a big problem as i on a regular basis back up the phone memory to the sim anyway in case i have to switch phones.
Im not sure why you guys are having problems but im happy to help in anyway.
I haven't rooted my device as i see no reason to just yet its all stock, and runs like a dream.
I have a ford mondeo with the STD sony system in it if that helps, oh and it connects as soon as i get in the vehicle
I think I may have cracked this:
I stuck a random contact on my SIM card, the Parrot handsfree now finds all of the contacts on the phone, and automatically links to the phone when in proximity. Odd, but adding that contact seems to have unlocked remote sim access.
Give it a try!
same here ... added one contact onto my sim, then full access to contacts!
Works very well with the Land Rover Bluetooth PTI (designed by Nokia as it happens). Full contact list navigation on the stereo head unit.
I am having a similar issue with an in car BT head unit. I have a Pioneer DEH-P7100BT. I have had problems connecting the hero to this. It starts contacts download and stops at contact number 14 for some reason. I have tried to delete the 14th contact but still gets stuck at 14. I have all my contacts backed up on the sim as well.
It is also proving to be an issue automatically connecting to the head unit when I get into the car. I resolve that by switching the BT off and then on again, then it connects OK. Not ideal.
The wifey has an Iphone 3GS and that connects to the unit every single time. No connection issues at all.
The BT Audio option works a charm with both the Hero and the 3GS. I usually play Last FM and Imeem over 3G and stream via BT to the head unit, pretty cool over all, if only I could sort out the connection issues with the HERO.
I just got the hero a couple of days ago, and although I am loving it, I really cant stand the lag in absolutely everything. I am having problems even accepting calls sometimes as it realises I have just clicked the receive call button after 10 seconds or so.
DJGurth said:
hello i have just got my hero and im still learning the in's and outs of the device as i have come from a WM device, but have loads of success so far.
I have a in car bluetooth system and i have no problems with connecting, and searching my sim card for contacts.
The problem i do have though is that it will not read my phone contacts just the sim.
Click to expand...
Click to collapse
Mine does it the opposite way - reads the phone memory and not the sim memory. It's taken me 2 days to complete changing the profiles of people so far as I couldn't figure out why active sync wasn't working.
My Atrix pairs up nicely with my '01 BMW's BT system, but will drop the connection after about 15sec, and then reconnect again, hold that connection for about 15sec, then drop it. Phone will show Paired but not connected, and the car will be in a similar state. Following other's suggestions, I cleaned out my Contacts-- even with no Contacts in the phone, the same thing happens.
Any idea what's going on? My iphone 3gs and 4 connected 100%, uploaded their Contacts, and never gave me a moment's problem, so I know the BT in the car is working OK.
Help!
Sorry to hear that. I have so far no problems with connecting my phone to my built in BT system. I have a Mazda 2010. I stream music and get incoming calls too.
I used a bt headset for an hour long conference call this morning. No lost connections yet. Reboot doesn't help?
Sent from my MB860 using XDA App
Nope, rebooting doesn't help. BT on the Atrix works just fine with my Panasonic house phone that has BT on it.
I had the same issue today in my 2010 Dodge Ram. Captivate worked great in it, but the Atrix dropped the BT/Call after 30-45 seconds or so. I haven't noticed it dropping connection when I'm not using the phone (I have an icon on my ent/nav headunit), only saw the icon disappear when on a call.
Exwoodchuck said:
My Atrix pairs up nicely with my '01 BMW's BT system, but will drop the connection after about 15sec, and then reconnect again, hold that connection for about 15sec, then drop it. Phone will show Paired but not connected, and the car will be in a similar state. Following other's suggestions, I cleaned out my Contacts-- even with no Contacts in the phone, the same thing happens.
Any idea what's going on? My iphone 3gs and 4 connected 100%, uploaded their Contacts, and never gave me a moment's problem, so I know the BT in the car is working OK.
Help!
Click to expand...
Click to collapse
OK, so I messed with it some more...
If I'm super-fast, I can dial from the car's BT system-- and the name of the phone does appear on the car's Nav. That is, until the phone and/or car drops the connection.
I've asked for help on Motorola's forum, and been tracking down a Product Manager @ ATT to get the word up the chain.
I have the same issue with my 04 3-Series. I posted about this in the Problem forum.
No bt issues here. I used it yesterday with a car kit/fm transmitter to stream Slacker and nav simultaneously to my stereo for a couple of hours and it worked great.
Ziuck said:
I have the same issue with my 04 3-Series. I posted about this in the Problem forum.
Click to expand...
Click to collapse
Think we've got the same BT ULF's in our car. Please let me know if you find a solution, and I'll do the same.
mgymnop said:
Sorry to hear that. I have so far no problems with connecting my phone to my built in BT system. I have a Mazda 2010. I stream music and get incoming calls too.
Click to expand...
Click to collapse
Can you skip forward and back and pause?
I could with the iphone but have not been able to get it to work with android.
The weirdest bit is that I got it to work for Pandora ONCE... then never again.
I think it has something to do with the way android treats certain devices... I have motorola BT stereo headphones that the controls worked for WinMo W7 and iphone, but do not work on any android device I've tried.
I also lose connection with the in car BT occaisionally but not very often and can usually get it to reconnect without much hassle.
2010 mazda 3.
Exwoodchuck said:
My Atrix pairs up nicely with my '01 BMW's BT system, but will drop the connection after about 15sec, and then reconnect again, hold that connection for about 15sec, then drop it. Phone will show Paired but not connected, and the car will be in a similar state. Following other's suggestions, I cleaned out my Contacts-- even with no Contacts in the phone, the same thing happens.
Any idea what's going on? My iphone 3gs and 4 connected 100%, uploaded their Contacts, and never gave me a moment's problem, so I know the BT in the car is working OK.
Help!
Click to expand...
Click to collapse
Just because it worked with your iPhones doesn't mean the BT module isn't faulty...it might just have trouble accepting connections from certain things. Not to say the phone's *not* at fault, but don't assume it's the phone when there's a chance it could still be the phone.
I have a kenwood bluetooth module in my receiver that worked perfectly with every phone until I got an iPhone 4 (even previous iPhones worked fine). It wouldn't connect and finally when I got it to work the sound quality was horrendous (most people couldn't understand a single word). I thought the phone was obviously bad until I contacted Kenwood and they sent me a beta driver for the bluetooth module in the receiver. Updated the driver and it worked perfectly.
I agree- the BT module *could* be fault, but given that it works with all iphones and my BB Bold, I'd have to say that it's more than likely something to do with the way the Atrix/Android handles the connection.
Others are now chiming in on the Motorola Forum about this issue- including someone who has a newer BMW BT module than I have - he's also got the same issue. There's also a Dodge owner earlier in this thread that's got the same problem.
On a whim, I copied 20 contacts to the SIM, thinking that might be the problem.
Same results.
i also had bt pairing problems with my ford sync, and it seems to be android related as it also happened with my n1.
couple things to try that should help: disable wireless and make sure you aren't using the power widget on one of your home screens. also, i used autostarts to unbind the media button pressed event, and between those three things, the bt works fine...
Tried an experiement-- copied some contacts to the SIM.
Same issue- phone connects/disconnect/connects/disconnects for good.
Exwoodchuck said:
I agree- the BT module *could* be fault, but given that it works with all iphones and my BB Bold, I'd have to say that it's more than likely something to do with the way the Atrix/Android handles the connection.
Others are now chiming in on the Motorola Forum about this issue- including someone who has a newer BMW BT module than I have - he's also got the same issue. There's also a Dodge owner earlier in this thread that's got the same problem.
Click to expand...
Click to collapse
Apparently you read my post...but didn't understand it completely.
My previous receiver worked *PERFECTLY* with all phones but the iPhone 4. I used about 20+ phones with it without a single problem...but the iPhone 4 wouldn't connect 3/4 of the time, and when it did it didn't transfer any contacts and when I made a call the sound quality was *very* bad. I obviously assumed it was the iPhone 4 until I tried another one with it...turned out it *WAS* the receiver having an older firmware that wasn't compatible with the iPhone 4.
The reason a lot of Audis and BMWs aren't working with a few Android phones (the Atrix being one of them) isn't because Android is designed poorly...it's because the firmware in the receivers doesn't handle the Android setup well. The reason most people can connect but can't get contacts is because the way BMW/Audis poll for Contact lists doesn't work with Android. The car manufacturers haven't spent the time required to realize this and put out a correction. You should be complaining to BMW or Audi about this (whichever type you own) and trying to get them to release an updated BT Stack for your receiver (they might say it's not possible but it is).
Thanks for the clarification.
I doubt that BMW is going to release a firmware upgrade for my BT module - its out of production, and it's already 'state of the art', circa 2006 when they stopped producing them. I've read of other issues with newer BMW and other cars still having issues with the Phonebook upload, which is where I think the problem lies. It doesn't seem to be isolated to older cars either- I've read of 2010 models having the same issue I've got, and not just from European makers.
Digging around, this is a common theme with Android and BT not playing nicely-- many other phone manufactures have released patches/updates to correct similar issues, and I'm hoping that with the Atrix being the 'biggest and baddest', that Motorola sees fit to do the same. I've got a $600 fully integrated factory BT system thats now useless, and I'd sure like to have it working again.
I sometimes forget that I've got another BT-enabled car to test on -- a 2010 Audi A3.
My Atrix paired with no issue, then popped up with a message in the Notification area about allowing access to the Contacts. Ahh-hah! When paired to my BMW, I never get that message. So... the BMW appears to be unable to complete the handshake for PBAP access, and when it fails, it drops.
After syncing with my BMW I do not get the PBAP confirmation.
I did not get the confirmation with my Inspire 4G either but that phone DID work just fine. Contacts and audio would work and never had a drop out when I had the phone.
So there is a way to "fix" this issue without updating the vehicles BT.
Tested with my car bluetooth with 2 calls for ~30 mins in all today morning. Worked fine. It stayed paired on all the time.
I know there are a variety of posts of many flavors in regards to OEM in car bluetooth handsfree systems. Some for unbranded i9100, some for the AT&T i777
For anyone out there with the knowledge: Is there anyway to find a task automater (like a macro) to lets say automatically activate the bluetooth button for the paired device, lets say 1 second after Bluetooth turns on. In connection with Auto Bluetooth app (like the ones which turns on when motion is detected) it could be automated. I would do it, except I don't know how to write program code.
I am thinking like "if bluetooth turned on, wait 1 second, trigger paired device input" . Because in that case it would connect (automatically) in most cases I though many many people posting around here.
Anybody any idea?
I am trying to connect my Galaxy S2 with they system in my 2011 Jaguar XJ. I never had a problem with my BlackBerrys. The BlackBerry autoconnects the moment I start the car and all functions work.
Absolutely not so with my S2. It seems that differnet car manufacturers differing systems which use BLuetooth differently. Some work, some don't .
Let me clearify the problem. Phone does NOT AUTOCONNECT and it drives me nuts. Before i just got in the car and never pulled the phone out of my pocket. Now I have to pull it out and manually connect.
I am posting as I may save some of you some time. I tried everything up and down the list. About every Bluetooth apps in the market place. Free or paid. Really pretty much all of them. Nothing worked. I upgraded to the (leaked) UCKJ1 and back to the original UCKH1. I rooted and unrooted.
To no avail. All I can do is use a shortcut widget to save me a few menues to navigate.
So for the ones with the same problem; you know all the things I tried. Don't waste your time.
It takes two devices to successfuly connect. If a connection doesn't happen, you can't blame just one device. My ISGS2 auto-connects to all of my devices (AV receiver, headset, PC, car, portable speaker, G-Tab) automatically every time. I get you're upset, but you can't single the phone out alone. As for cars, in the ISGS2 forum, non-iDrive (older) BMW's were the majority of the problem.
Same here. I have no problem auto connect to my BT devices. But when it comes to BT auto connections, problems are common. Both sides of the BT connection can be the cause.
Well depending on the year, make and model of the car with bluetooth. Really need more information. What Barry said is oh so true and usually anyone can tell you what their experience is. My experience with my daily driver's system *Alpine CDA 9887, Alpine KCE-BT400 made by parrot*, works flawlessly. The only time I ever had to manually connect was right after getting my sgs2 and even my captivate connected properly unless I was connected to my jawbone icon when I jumped in my truck.
HTH,
Charlie
Mine connects flawlessly in my 2010 Camaro SS.
Im in a 2011 Camry SE, and with stock ROM it connects automatically. With CM7.1, I just have to take it out of sleep, by turning on the screen, and it connects. Not a big deal.
Sent from my SGH-I777 using XDA App
Hi, Thanks to all for the responses. I completely agree that it takes two devices to do it right and I am fully keeping that in mind. I have 2 more cars I can try with. So I will check if it works with my wife's Lexus and with my Clarion system in another car I have.
It just is, that my BlackBerry (which I don't miss at all) simply did the job perfect. Obviously I can't tweak anything on the car side as that is next to impossible. There is no open source code and all is so proprietary.
So the only hope I have is to figure out a way to teach my SGSII.
Again thanks for the input. I do absolutely LOVE my Galaxy S2 (i777) therefore this is a simply irritating that I have to push buttons when I get in the car.
Hearing that it works for most of you is well, good for you and not so good for me.
Blaze9 said:
Im in a 2011 Camry SE, and with stock ROM it connects automatically. With CM7.1, I just have to take it out of sleep, by turning on the screen, and it connects. Not a big deal.
Sent from my SGH-I777 using XDA App
Click to expand...
Click to collapse
dmnall said:
Well depending on the year, make and model of the car with bluetooth. Really need more information. What Barry said is oh so true and usually anyone can tell you what their experience is. My experience with my daily driver's system *Alpine CDA 9887, Alpine KCE-BT400 made by parrot*, works flawlessly. The only time I ever had to manually connect was right after getting my sgs2 and even my captivate connected properly unless I was connected to my jawbone icon when I jumped in my truck.
HTH,
Charlie
Click to expand...
Click to collapse
Well, I will experiment a bit more and I will share what I will find in case others have similar problems.
This reminds me of a blog post ages ago called "Bluetooth needs a dentist"
The state of Bluetooth compatibility is abysmal in general... What is exceptionally sad is that 4-5 years ago or so, one of the most relibale and compatible Bluetooth stacks around (BlueZ) got a bunch of nastygrams from the Bluetooth SIG regarding failure to run the "offficial" compatibility/interop tests.
The short summary: Bluetooth compatibility is an epic nightmare, on both sides of the coin (host and device).
Entropy512 said:
This reminds me of a blog post ages ago called "Bluetooth needs a dentist"
The state of Bluetooth compatibility is abysmal in general... What is exceptionally sad is that 4-5 years ago or so, one of the most relibale and compatible Bluetooth stacks around (BlueZ) got a bunch of nastygrams from the Bluetooth SIG regarding failure to run the "offficial" compatibility/interop tests.
The short summary: Bluetooth compatibility is an epic nightmare, on both sides of the coin (host and device).
Click to expand...
Click to collapse
Hello,
I have to fully agree with Entropy512. Bluetooth compatibility is a disaster. Especially after all the years around. Not sure who, what and where is deciding on BT specs, drafts and so forth.
I know that with car systems it is a hit and miss. But it doesn't have to be. We all know that. I was digging on my good old Jaguar forum. What I found confirms exactly what we are saying.
Earlier Samsung Androids barely could hold a connection on Jaguars systems. Just with later versions and Gingerbread that was resolved. And none of the Samsungs autoconnect to any Jaguar system. And that is the same for Audi, Merceds and Subaru and probably some others. According to the Jag forum Samsung knows about this and worked on it.
But here is the main problem. On my wife's Lexus and on my Clarion head unit in my van it works like a charm. Automatically connects without a hitch. I understand Samsung can fix that but than it may not work on other cars. But how come BlackBerry was able to do what the Samsung unit can't???
And yes, some features like phonebook, direct dial and so forth are totally hit and miss. How do car unit manufacturers test? With what? Just one phone from 3 years ago? Same with the phone manufacturers. Is anybody talking? Seriously, why can't car head units manufacturers and phone manufacturers not figure out how to get on the same page? Car BT is becoming a standard equipment. So do BT enabled phones, no matter smart phones or what have you. There are not that many head unit manufacturers. So they can't agree on a standard which then can be used by the devolpers for a decent BT stack for phones? Completely ridiculous. Can make phones talk to you like the Apple Siri but can't get a bluetooth connection.
OK, I got that off my chest. Now I will try to get to work. All I can do is working on the i777 side, because there is no acces to anything on the Jaguar side.
Funny thing is, my phone is always stating phonebook request when I get in the car. Eventhoug I turned phone book off in the car. So the phone "hears" the car. Just without hitting the profile for the car it won't connect.
Auto connect to my Mazda 6 no issues. Same with all my other phones.
Sent from my SAMSUNG-SGH-I777 using xda premium
cpcrazyfly said:
Auto connect to my Mazda 6 no issues. Same with all my other phones.
Sent from my SAMSUNG-SGH-I777 using xda premium
Click to expand...
Click to collapse
Do you have problems with the Mazda taking too long to switch from "Music" mode to "Headset" mode, thus the vlingo voice prompt timing out? My mazda has that issue and it makes vlingo in the car pretty much useless.
I don't typically use voice commands but ill try. It has no issues taking and making calls then going right back to google music streaming.
Sent from my SAMSUNG-SGH-I777 using xda premium
I am also experiencing sporadic problems with my SGS2 and 2011 VW Golf using BT. About 75% of the time, it auto-connects fine when I start up the car. The car lets me know it linked and I can make/receive calls through the car's BT system fine. Address book loads as well (though does require a secondary authorization on the phone the very first time you use it).
However, every once in a while it either can't "find" the phone, or goes into a continuing looping state of "paired/not-paired". Generally when I actually want to use it! When it can't find the phone, manually searching for it (on the car's system) usually rectifies it temporarily, but it may go to unpaired a few minutes later. And on occasion, it simply can't find it at all. When I reboot the phone, or disable/re-enable BT on the phone itself, this problem usually goes away. This makes me think it's more of an issue with the phone then the car.
I too came from a BlackBerry torch and never once had a single pairing problem with my car.
When paired, media streaming generally works well, but occasionally I have to stop/restart it a couple times in order for the car to 'see' the media stream and allow me to chose it as the input.
The problem that I have is that the sgs2 will not report signal level to the car, so the car always shows full signal, even if i have no signal.
And it doesn't connect to the car unless the phone is in the car when the car starts. If bluetooth is turned off, or if I leave the car and go out of range, I will have to open the settings and force a connection.
Problem Solved, Autoconnect now working
Problem solved, read on:
This seems to apply to a variety of other vehicles, namely Jaguar, Mercedes, Audi, some BMW, Nissan and Subaru.
You can get your phone bluetooth auto connect to your vehicle by trying the following:
Attention, I believe this works for rooted phones only.
Get a app such as Titanium Backup Pro or MyToolbox.
under System Apps freeze "Bluetooth Share".
Now my phone automatically connects to my Jaguar XJ and all features seem to work. Having gotten around to check the phonebook yet. But all recent number log show and all seems to work.
Attention: I believe that may only work for rooted phones.
metalco said:
Problem solved, read on:
This seems to apply to a variety of other vehicles, namely Jaguar, Mercedes, Audi, some BMW, Nissan and Subaru.
You can get your phone bluetooth auto connect to your vehicle by trying the following:
Attention, I believe this works for rooted phones only.
Get a app such as Titanium Backup Pro or MyToolbox.
under System Apps freeze "Bluetooth Share".
Now my phone automatically connects to my Jaguar XJ and all features seem to work. Having gotten around to check the phonebook yet. But all recent number log show and all seems to work.
Attention: I believe that may only work for rooted phones.
Click to expand...
Click to collapse
I'm going to try this...
I've been having trouble with it automatically connecting to my 2011 WRX. My iPhone 4 always connected immediately, no problem. But the GS2 has yet to automatically connect, ever. It is paired fine and if I go into the Bluetooth settings, it is paired OK and I can manually tell it to connect. I've tried deleting the connection both from my head unit and the phone and recreating everything multiple times. Still no luck.
I'll try this and report back.
Bluetooth is def one of those technologies that could be enormously awesome but often has so much "fussiness" with it (due to incompatibilities or quirky behavior between varying BT devices) that it can easily become a right-royal PITA, IMO.
I've had quite a few Android phones over the years, now, and tried running both stock OS and many different ROMs on them with one of the expected primary functions of my phone to be as my main music player, including streaming music via BT/A2DP to my car stereo and this one function has ALWAYS proven to be the most frustrating experience. So yeah, I'll fully agree that whomever is "calling the shots" with setting up guidelines and specifications for BT and BT-based devices needs to get themselves an iron fist and put an end to this crap of inconsistent behavior and general flakiness.
When I got my AT&T SGS2 I was shocked to see that Samsung had done something to enable their stock music app to be able to transmit song metadata via BT. Android thus far has only supported AVRCP 1.0 (AFAIK) while you need AVRCP 1.3 (or higher) to be able to have metadata transmit over BT. At first I was ecstatic that FINALLY I could see my song info from my phone displayed on my car stereo while connected via BT. But then I found out that with the SGS2 and the stock music app my car stereo could no longer successfully send play/pause/forward/reverse commands to my phone! D'oh!!!
So then I went back to Poweramp (what I had been using for my primary music app on my previous phone; a Nexus S) and of course it wouldn't display the song metadata. But the big shocker was that it also couldn't recognize control commands issues from my car stereo! Not cool!
I did much tinkering and research and finally found that the music app PlayerPro would successfully work with my head unit (but still no metadata, of course) and so that's where I'm at.
Ridiculous, IMO. Nobody should have to endure such frustrating behavior with BT devices. I really wish somebody could straighten this kind of mess out in regards to Bluetooth and get things to "just work".
No luck for me. Freezing the Bluetooth Share did not fix my auto-connect problem.
ack154 said:
No luck for me. Freezing the Bluetooth Share did not fix my auto-connect problem.
Click to expand...
Click to collapse
OK, you can try one more thing;
Freeze all of those files: BluetoothPBAP, BluetoothShare and BluetoothAvrcp. If you have any other entries you can try freezing them, too. Just everything EXCEPT anything with a name like Brcm or BrcmBluetoothServices.
Just try it. And MAKE SURE to wipe cache after freezing, or better reboot. Also you want to make check they are in a "frozen" state after rebooting. I used "MyToolbox" and it worked perfect.
I haven't checked if I can still stream music, but I never use that anyways. I froze all of those and started unfreezing one by one. The experiment showed that in my case I only had to freeze the BluetoothShare. You may have to freeze the others, too.
Let me know how ot works. I am curious now.