Related
Hi
This topic has been created to address FAQ in regards to Feeyo's Cronos Droid.
This will allow Feeyo to work and post relevant updates on his thread in Development.
Basics:
To ensure the update goes as smoothly as possible, please ensure you carry out the following:
Feeyo has recommended you setup your SD card as follows:
first partition :ext2
Rest FAT32
Some users have advised ext3 has worked, if so great
Installation Instructions
1) Do a backup
2) Make sure you wipe everything. (also battery and rotating settings)
3) Flash Cronos
4) Reboot.
5) When finished booting for the first time make sure to reboot it one last time to update all caching and settings.
Are u updating the rom from an older Cronos Droid version?
1) Flash Cronos
2) Reboot.
3) When finished booting for the first time make sure to reboot it one last time to update all caching and settings.
I update from Cronos Droid Version 1.4 to 1.4.1
In 1.4 rom ，there was about 140M left in my telephone memory
after the update ， there is only 108M left in the telephone memory
then I did this：
adb shell
su
cp -a /data/app /system/sd/
rm -r /data/app
ln -s /system/sd/app /data/app
reboot
there is still 108M left
Then I find the apks exist under data/app also exist under system/sd/app
if i delete the apk under data/app,the same apk will also disappear
WHY
PS after full wipe and I flash the 1.4.1 ,reboot,flash the app2sd.zip ,the phone died,the 1.4.1 means this one :StableCronos_4.1_528_fix_sign.zip
SD：swap 32M ；ext3 512；fat32 some rest
jyhwai said:
I update from Cronos Droid Version 1.4 to 1.4.1
In 1.4 rom ，there was about 140M left in my telephone memory
after the update ， there is only 108M left in the telephone memory
then I did this：
adb shell
su
cp -a /data/app /system/sd/
rm -r /data/app
ln -s /system/sd/app /data/app
reboot
there is still 108M left
Then I find the apks exist under data/app also exist under system/sd/app
if i delete the apk under data/app,the same apk will also disappear
WHY
PS after full wipe and I flash the 1.4.1 ,reboot,flash the app2sd.zip ,the phone died,the 1.4.1 means this one :StableCronos_4.1_528_fix_sign.zip
SD：swap 32M ；ext3 512；fat32 some rest
Click to expand...
Click to collapse
Feeyo has advised not to flash the aps2sd zip (first post) with 1.4.1
Q: Im in love with Feeyo, what do I do
A: get in line behind Rhamsterman
Q: All apps that need SU access on the SU request screen - hanging
A: enable usb debugging
akhtar1817 said:
Feeyo has advised not to flash the aps2sd zip (first post) with 1.4.1
Click to expand...
Click to collapse
yes，I know it ，now I am using the room without flashing the aps2sd zip
but,the problem still exists
jyhwai said:
yes，I know it ，now I am using the room without flashing the aps2sd zip
but,the problem still exists
Click to expand...
Click to collapse
you mean apps2d is not working? I think he is working on it as a few people have posted the issue
akhtar1817 said:
you mean apps2d is not working? I think he is working on it as a few people have posted the issue
Click to expand...
Click to collapse
yeah, that is the point wired
normally ,if the apks you install are all under /system/sd/app,it means the app2sd works
but this time they were under /system/sd/app and also under date /app which
takes up the phone memory
supposed to be QA thread right?
Only questions with answers here please.
Q1: I want the vanilla lockscreen like the one on previous builds of feeyo rom?
Q2: I also need a solution for stopping the alarm on this new lockscreen?
Q3: My phone freezes after the phone starts after applying this update?
A1: Read here. http://geekfor.me/fixes/vanilla-lockscreen/ (works on every 2.1 rom, tested myself manytimes)
A2: Alarm in sense clock is connected to sense lockscreen. If you disable this by installing vanilla lockscreen you won't be able to stop the alarm when it starts. So download also the default clock app (found in link above) and set the alarm in that clock app and disable the alarm in sense clock app.
A3: This lockscreen does not have a pin unlock screen built in. So if you want to use, disable the PIN before flashing the update.
IMPORTANT: If you do this you will lose HTC lockscreen. If you want it back it is only possible by reflashing the rom you use (no wipe needed!). Also (i couldn't find it now), but there is also a solution for having a non transparent lockscreen. It somwhere in the web. Use google.
Q: How do I get MMS working?
A: (Full credit to Goose247 for this)
Copy your data/data/com.android.providers.telephony/databases/telephony.db over to your computer.
Download this http://sourceforge.net/projects/sql...0 beta1/sqlitebrowser_200_b1_win.zip/download
extract it and run "SQLite Database Browser 2.0 b1"
Open up telephony.db
Click on "Browse Data"
Next to table, click on the dropdown menu and select "carriers"
in table 2 (production) you want to change only these settings (apn, user, password, mmsproxy, mmsport, mmsc and just check that type is set to mms) - I didn't have type anything in user and password, guess that depends on your carrier (tmh)
Scroll down the list of carriers to find your settings for the above.
To change any value just double click in the relevant box and input your value and remember to click on "Apply Changes"
Once you have change all your settings save, upload your new modified telephony.db to your phone and then reboot phone.
Click to expand...
Click to collapse
Q: My market seems to load up very slow.
A: When starting the market just press search, and enter a program name. dont wait for it to load up. It will speed it up right away.
Q: Nope it is still being slow...
A: Is your gmail syncing at the same time when using the market? That will slow down market.
akhtar1817 said:
Installation Instructions
1) Do a backup
2) Make sure you wipe everything. (also battery and rotating settings)
3) Flash Cronos
4) Reboot.
5) When finished booting for the first time make sure to reboot it one last time to update all caching and settings.
Are u updating the rom from an older Cronos Droid version?
1) Flash Cronos
2) Reboot.
3) When finished booting for the first time make sure to reboot it one last time to update all caching and settings.
Click to expand...
Click to collapse
I follow this instruction but final can't boot, stop in HERO screen after flash, I was tried many time.
Normal for this version how long to fist boot???
Feeyo said:
Q: My market seems to load up very slow.
A: When starting the market just press search, and enter a program name. dont wait for it to load up. It will speed it up right away.
Click to expand...
Click to collapse
does not work for me
at market startup
i press the search button, enter a name...
after 1 minute i get a result
apps install slow, and after it is installed, it still says 'installing' in the market
Q: My 3G seems unstable / slow Internet
A: The automated APN settings are probably not correct. Remove the automated APN's from your system and enter them manually.
where is this apps2sd.zip file ?
Is it possible to remove / hide the clock in the top right corner? I don't need this, while having a clock widget.
Is it possible on Android at all or specific for this rom?
NoClaim said:
Is it possible to remove / hide the clock in the top right corner? I don't need this, while having a clock widget.
Is it possible on Android at all or specific for this rom?
Click to expand...
Click to collapse
what clock widget are you using instead?
wieben said:
what clock widget are you using instead?
Click to expand...
Click to collapse
Any clock widget will display a clock on the home screen....the clock in the top right corner is useless then, while I don't need to read the time twice...
hi can some one tell me how to Enable JIT on my Optimus One.
I need a very simple guid.
Thy.
imapjonny said:
hi can some one tell me how to Enable JIT on my Optimus One.
I need a very simple guid.
Thy.
Click to expand...
Click to collapse
Root your phone
Install custom recovery
Download flashable zip that enables JIT
flash it
kite86 said:
Root your phone
Install custom recovery
Download flashable zip that enables JIT
flash it
Click to expand...
Click to collapse
I'm pretty sure that he wants a easy and detailed guide.
Domenic.
1. Does Z4Root work on this work?
2. What is a good custom recovery to use? does cwm work?
imapjonny said:
hi can some one tell me how to Enable JIT on my Optimus One.
I need a very simple guid.
Thy.
Click to expand...
Click to collapse
Once you've got the custom recovery on it's easy. Copy the jit enabling zip file to the root of your sdcard, reboot into recovery and choose flash zip from the recovery menu.
yes z4root is working!
I need a giud how to install custom recovery to
imapjonny said:
I need a giud how to install custom recovery to
Click to expand...
Click to collapse
http://androidforums.com/getitnowma...ry-optimus-one-p500-thunderg.html#post1896517
To use copy flash_image and recovery-RA-GNM-thunderg-1.1.0.img to the root of your sdcard.
To flash: via adb shell or terminal type this from root # shell
Code:
# mount -o remount,rw -t yaffs2 /dev/block/mtdblock1 /system
# cat /sdcard/flash_image > /system/bin/flash_image
# chmod 755 /system/bin/flash_image
# mv /system/etc/install-recovery.sh /system/etc/install-recovery.sh.bak
# mount -o remount,ro -t yaffs2 /dev/block/mtdblock1 /system
# flash_image recovery /sdcard/recovery-RA-GNM-thunderg-1.1.0.img
# reboot recovery
Key combo to boot custom recovery from powered off is vol_down + home + power and release keys at LG splash.
Click to expand...
Click to collapse
I m realy new in this scene
what is adb shell and where can i get it ?
imapjonny said:
I m realy new in this scene
what is adb shell and where can i get it ?
Click to expand...
Click to collapse
You can download Android SDK - this shell is part of this development tool
imapjonny said:
I m realy new in this scene
what is adb shell and where can i get it ?
Click to expand...
Click to collapse
Or root and get terminal app.
Either way, I tweaked mine for a vm.heapsize of 48mb.
JIT sure is handy but what about GPU accel?
I have flashed with jit zip.
I test the phone before,
with linpack,average result 3.5M
After flash with jit,actual result 7.8M
During the normale use i don't see evident boost performarce,
but for me is a good update.
Bye.
Sorry, but I thought Android 2.2 had the JIT compiler built in? It's turned off on the Optimus T?
This is my wife's phone, and in general it has good performance. But Angry Birds runs a slow on some of the screens. I was wondering if enabling the JIT compiler might help.
BTW, I've rooted the phone already to modify the SMS send limits.
Froyo normaly make active jit,
but on O1 this feature is not active by default.
If you have rooted the phone,install the recovery menu and flash with jit zip.
greno1 said:
But Angry Birds runs a slow on some of the screens. I was wondering if enabling the JIT compiler might help.
Click to expand...
Click to collapse
No that does not help, I have tested that. Removing the ads with adfree android seems to help a little bit, but generally the phones cpu has not enough power for angry birds.
The Angry Birds developers are working in a lower spec version that will run on 600mhz Arm6 processors more smoothly.
Just in case, figured someone would want it at some point.
dl-dropbox-com/u/13427114/signed_thunderc_thungerg_jit_disable.zip
(add http and replace - for dots)
Noejn said:
Just in case, figured someone would want it at some point.
dl-dropbox-com/u/13427114/signed_thunderc_thungerg_jit_disable.zip
(add http and replace - for dots)
Click to expand...
Click to collapse
you can also delete /data/local.prop and reboot too.
Or, flash this one which will not only enable JIT and change the vm.heapsize to 48mb but also enable hardware acceleration. Homescreen should be snappier.
dl"dot"dropbox"dot"com/u/13427114/mone/o1_jit-hwacc_enabler.zip
(add http and replace "dot" for .)
how should i install this? (Searched over the net and couldn't find how to install)
Will this increase my gaming and mobile performance ??
I have lg official 2.3.3 Rom, With franco kernel and also have SetCpu installed.
globeent1980 said:
how should i install this? (Searched over the net and couldn't find how to install)
Will this increase my gaming and mobile performance ??
I have lg official 2.3.3 Rom, With franco kernel and also have SetCpu installed.
Click to expand...
Click to collapse
Its enabled by default
Sent from my LG-P500
This is only for use on the X10 Mini Pro.
Credits go to nobodyAtall & D4rKn3sSyS for the actual CWM files. Other credits in the README.txt file.
Both version currently use CWM v3.x r5
Windows
Requirements:
Windows PC
USB Cable
Phone driver installed
Android Version 2.1 Stock ROM (2.1.1.A.0.6) (May work on Froyo and Gingerbread ROM's but any custom ROM should have a recovery already installed)
Usage:
You need to set your phone in Debugging Mode.
Connect your phone to your computer
Open up install.bat and follow the instructions inside that.
CWM Usage:
When booting your phone and when the 'Sony Ericsson' letters appear, press and release continuously the 'back' button.
Once you are in the CWM recovery, use the volume keys to navigate upwards / downwards, the 'home' or camera button key to select, the 'back' key to go back.
Last Update:
21-03-2012 v5
Updated Superuser apk and su to version 3.0.7
Replaced SuperOneClick with alternative method
Prefixed relative paths with %~dp0 to complete full paths. This is to combat over zealous group policies. Thanks go to satanselbow
Linux
Requires your phone to be ROOTed but there is now a ROOTer for Linux that can ROOT your phone if not already done. Can be found in this forum.
Requirements:
*nix PC/Laptop
USB Cable
Android Version 2.1 Stock ROM (2.1.1.A.0.6) (May work on Froyo and Gingerbread ROM's but any custom ROM should have a recovery already installed)
Usage:
You need to set your phone in Debugging Mode
Connect your phone to your computer
Open up terminal
Go to the directory it is extracted to
Start the installer by typing "sh cwm-x10minipro.sh"
CWM Usage:
When booting your phone and when the 'Sony Ericsson' letters appear, press and release continuously the 'back' button.
Once you are in the CWM recovery, use the volume keys to navigate upwards / downwards, the 'home' or camera button key to select, the 'back' key to go back.
Last Update:
23-Sept-2011 (v4)
Fixed question about USB Debugging
Fixed permissions on ADB
Links:
Original X10 Mini CWM Thread: http://forum.xda-developers.com/showthread.php?t=1105745
Original X10 Mini Pro CWM Thread: http://forum.xda-developers.com/showthread.php?t=1106146
Changes:
The changes for the latest version are included in the relevant sections above. A more detailed list of changes across all versions is in the CHANGES.txt file that is in the archive file.
Download:
Windows: Download
Linux: Download
Please do not re-host or re-release without permission.
Don't forget if you found this helpful please push the "Thanks" button
copy failed read only file system
is this basically a batch file?
because if so i could port it to linux for you
mopgawka - Did you get the correct mtdblock number. The file would set the system dir as r/w to enable you. The mtdblock number is the number directly after the text mtdblock, in the image below it is 0.
Another question was there an error after the "Getting ROOT rights" text? This was the bit that caused me the most issues.
x10man - Yes it is just basically a batch file. If you want to port to linux then go ahead
ClockWorkMod Recovery Installer for X10 Mini Pro by rect2409.
Requirements and credits are listed in the README.txt file.
Please make sure requirements are met before continuing.
...
..
Для продолжения нажмите любую клавишу . . .
Starting ADB Server if not started.
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
Getting ROOT rights.
rootsh: permission denied
Usage: mount [-r] [-w] [-o options] [-t type] device directory
Enter the mtdblock number listed "/dev/block/mtdblock? on /system"
Enter mtdblock number: 0
Mount system as R/W.
mount: Operation not permitted
Do you already have a recovery installed? (Y/N):n
Pushing recovery tar file.
failed to copy 'recovery\recovery.tar' to '/system/bin/recovery.tar': Read-only
file system
Pushing chargemon.
failed to copy 'recovery\chargemon' to '/system/bin/chargemon': Read-only file s
ystem
Setting permissions for recovery tar file.
Unable to chmod /system/bin/recovery.tar: Read-only file system
Setting permissions for chargemon.
Unable to chmod /system/bin/chargemon: Read-only file system
Stopping ADB Server.
* server not running *
..
i always rooted
Ok, Currently working on a new version which hopefully fixes your issues.
Thanks I will dl it and take a look later and post the result here
Sent from my U20i using XDA App
how did you root your phone? I also don't have a script called "rootsh". also you can check if you are rooted with "id". many ppl like me are just rooted after entering the shell
also it's better to use "su" when calling commands that have to be done by root: "su - -c 'mount xyz' "
also don't forget the "*" if you check for keyboard inputs (there are people that may miss the key they wanted to push .D)
good luck.
Finnaly! Thank you! Would love to see cwm being imported in the slades kernel, that way we never have to deal with broken files!
Snoopo said:
how did you root your phone? I also don't have a script called "rootsh". also you can check if you are rooted with "id". many ppl like me are just rooted after entering the shell
also it's better to use "su" when calling commands that have to be done by root: "su - -c 'mount xyz' "
also don't forget the "*" if you check for keyboard inputs (there are people that may miss the key they wanted to push .D)
good luck.
Click to expand...
Click to collapse
Yeah I just noticed that i left rootsh in there. Was just something I was playing with.
One thing I hate is Permission Denied error's with adb... Oh fun.
damn. i just did the port and managed to delete the files. DAMN windows temp file thingys anyway tommorow it will be done
TY man u awesome!!!!! thx u all work fine!!!!
rect2409 said:
mopgawka - Did you get the correct mtdblock number. The file would set the system dir as r/w to enable you. The mtdblock number is the number directly after the text mtdblock, in the image below it is 0.
Another question was there an error after the "Getting ROOT rights" text? This was the bit that caused me the most issues.
x10man - Yes it is just basically a batch file. If you want to port to linux then go ahead
Click to expand...
Click to collapse
In linux we used to set the mount point to a variable and then issuing the r/w command. I don't know how you can do this trick in windows.
Code:
mtd=mount | grep system | awk '{print $1}'
echo "Mounting /system rw"
mount -o remount,rw -t yaffs2 $mtd /system
The question about the mount point isnt in the newer version. It just assumes that the system mtdblock is 0.
If it causes a problem in the future I may change it back to selecting the mtdblock number but from all the times I have tried the mtdblock on the x10 mini pro has always been 0.
In windows the answer is just saved as a variable that you assign to the question.
Sent from my X10 Mini Pro using XDA App
Updated with v3.
Just added new way of gaining ROOT access and another check to make sure phone is ROOTed.
EDIT: Oops forgot I had posted last :/ Sorry
3.2.0.0-r3 is old newest is 3.2.0.0-r5
I tried to fix permissions but it's been doing that for almost an hour now... Is that normal, to take that long? Should I remove the battery?
EDIT: Forget it, after looong time waiting, it's finished
EDIT 2: It erased all my preferences! Is that supposed to happen?
I have never had to fix permissions myself so I don't know the process it uses. You could try in the CWM thread where they should be able to help you. Link is http://forum.xda-developers.com/showthread.php?t=1106146
Sorry
quangnhut123 - I don't have that version of CWM and the CWM thread only has r3. If you have r5 then could you give me the files please and will update it.
rect2409 said:
I have never had to fix permissions myself so I don't know the process it uses. You could try in the CWM thread where they should be able to help you. Link is http://forum.xda-developers.com/showthread.php?t=1106146
Sorry
quangnhut123 - I don't have that version of CWM and the CWM thread only has r3. If you have r5 then could you give me the files please and will update it.
Click to expand...
Click to collapse
r5 is the one with multiboot i believe
x10man said:
r5 is the one with multiboot i believe
Click to expand...
Click to collapse
Ahhh. Okay didn't realise that.
Have uploaded a version that includes r5 for the people that have to have the latest... Also kept v3 up as all that has changed is the CWM version.
[FAQ] >> RBAP for miniCM7 by nAa, nAa's kernel X10mini/X8/x10miniPRO .: 03/12/2012 :.
Read Before Asking Please
FAQ for MiniCM7, nAa kernel, FXP (should be added soon) and any other custom rom maybe
reading may answer to lots of your questions !
for X10mini, X8 & x10miniPRO
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
since people do not pay attention at this FAQ linked in miniCM7 first post,
[*]i decided to create a new thread dedicated to Q&A about miniCM7 and nAa's kernel
this thread is the place of your questions, answers, tips about nAa's kernel and miniCM7 by nAa
so please, as usual, read FAQ, use search option or anything else before asking commonly answered questions
the FAQ will be incremented when needed
the Q&A are in random order
before all the Q&A below : one is most important :
in order to install miniCM7 2.1.X you NOW need :
- to read this upgrade guide
- to read that post
- to unlock your bootloader (see also here)
- to flash nAa's kernel for X10mini, for X8, for x10miniPRO
if not, you will brick your phone. -> read this then, that may help you : !!!!
--> i think it is still too small ...
something else that is useful to read before asking :
Here we (nearly all? XDA members, regardless of being devs or only users [like me], me at least ) don't care about your good/bad English the important is trying to be understood and to understand the content of the threads
only ask things you can't find, or you don't understand, please if you don't understand something in any process tell us exactly where is your problem : it will optimize the answer
sometime rephrasing things can make you understand better, feel free to help us for making the most understandable sentence for anybody
i'm always trying to use a proper English (not so easy for a non native English ^^)
but if there's something misunderstood because of my English your are welcome to correct me
BUT if you don't make the effort to read, I won't make the effort to answer (ok, you can't read everything... but read the minimum )
that's it
Instructions regarding miniCM7-2.1.X installation:
Download the latest all-in-one package from the release link that follows
Backup your /data contents: contacts, apps, sms, etc. or backup via recovery
Move the MiniCM7-xxx.zip to the root folder of your sdcard and rename it to update.zip. Optionally, download the suggested Google Apps for CM7 (check http://cmw.22aaf3.com/gapps/ if you want to experiment with other gapps versions)
Unlock your bootloader, if you haven't already, using the stuff in unlock/ folder. Check http://forum.xda-developers.com/showthread.php?t=1254225 for a nice tutorial
Flash the nAa kernel using Flashtool. To to this:
- Turn off your phone
- Start the Flashtool\X10FlashTool.exe and select Flash. Then select the E10_nAaxxx kernel firmware (this flashes both the kernel.sin and the loader.sin)
- Keep the back button pressed while connecting the usb cable. Flashtool should detect your phone and flash the kernel.
- Once done, disconnect the usb cable and power on the phone.
Once the logo appears, press the back button repeatedly to enter CWM4.x.
- Select 'backup and restore -> Backup'
- Select 'wipe data/factory reset' (SUGGESTED)
- Select 'apply update from sdcard'
- Flash gapps
Reboot (first boot will take ~2 mins)
Once your device has booted, you can navigate to CM Settings -> System -> Update notifications and select 'Register'. This way you can get update notifications on new versions of MiniCM7!
>>>IMPORTANT GUIDE FOR USERS WITH PERFORMANCE PROBLEMS. <<< by ronaldvalles, thx to him
miniCM website is now available
clic on the red text above Chatroom for support is now available
clic on the red text above
register, and then enjoy
tell your device's name, and the rom+kernel you are using________________________________
FAQ :
for miniCM9 refer to THIS THREAD PLEASE
for quick search, use ctrl+f and enter keyword, you should find an answer to your question
1/ I can’t see incoming call number, what can I do ?
Change CM Settings -> Lockscreen -> Style options -> Incoming call style choose sliding tabs
2/ my LED is not blinking properly is there any way to change that?
If you’re using miniCM 2.0.5 you must delete delete /system/lib/hw/lights.x10mini.so
If you’re using miniCM 2.0.6 & 2.0.7, 2.1.0,2.1.1, 2.1.2or2.1.3 you must delete /system/lib/hw/lights.robyn.so with rootexplorer or any other file manager that allows you to explore and modify root files
handcent led settings does not work properly with lights.robyn.so
of course, you need to reboot your phone after that.
then : After the restart, go to CyanogenMod settings/Interface/LED notifications/Advanced make sure everything is unchecked, select Reset and then reboot again.
of course, you need to reboot your phone after that.
also try this : go to CyanogenMod settings/Interface/LED notifications/Advanced then tick and untick "random colors" this may solve everything if not :
MarkMRL said:
By ticking and unticking everything a few times randomly, I probably triggered the random flag to update correctly, thus fixing the blinking color. Now I can select a color and have it blink normally.
Click to expand...
Click to collapse
you can"t delete the file? see q33/
REDELETE AFTER EACH UPDATE if you have the same problem SINCE THE FILE IS REWRITTEN
this Q/A2 is also True for all builds of MiniCM9 and 10
3/I want SE stock keyboard on this ROM !!
Just long press on any txt you’re typing on, “choose input method” then choose default input
4/ I’m already running an older version on miniCM7 (2.0.4 for example) do I have to perform a factory reset/ full wipe ?
There’s no need to factory reset in that case
you may have to perform this to avoid performance issue : here
5/ I’m already running an older version on miniCM6 (1.0.2 for example) do I have to perform a factory reset/ full wipe ?
Yes, absolutely, same as if you were under gingerDX, SE stock rom or any other non miniCM7 based. you will loose ALL your data that are on phone memory (sms/mms, contacts, calendar...) if you're sync to a google account, your contacts and calendar should be preserved
q4/ and q5/ : to upgrade from any version of miniCM below 2.1.X you need an unlocked bootloader, and to flash nAa's kernel !
all is explain in the first lines of this post
6/ how can I activate overclock or undervolt ?
Open CMsettings/performances/CPUsettings/ then tick overclock OR undervolt, undervolt is automatically activated with overclock.
Remember not to tick “set on boot” option if you’re trying frequenies upper than 710 that could make your phone unstable or being damaged.
for miniCM7 2.0.6 you also need to flash the module hotfix to see overclock/undervolt working
no need to install that for 2.0.7, see Q 16/
for nAa07+ and miniCM7-2.1.6+, Open CMsettings/performances/CPUsettings/,
Remember not to tick “set on boot” option if you’re trying frequenies upper than 710 that could make your phone unstable or being damaged.
Since OC is now embedded in kernel, no module to enable (so OC option disappeared!), if you want to OC only, just choose the freq, if you want to undervolt too, tick undervolt option !
7/ i'm actually using Xrecovery can i install miniCM7 directly ?
no, you can't, you first need to install clockworkmod recovery from the link given in the first post (put in on the root of your sd card, then reboot to recovery, "install custom zip", reboot : cwm recovery is now installed, you can flash this ROM )
8/ i can't download some apps from the market
download 'market enabler' and select T-mobile Usa as fake provider, then retry to search and download them. that should work
9/ random problems that are unknown for anyody?
reflash the rom, i.e. reinstall the rom zip trough recovery
&/or
first backup, then do a factory reset, or restart from the beginning, it could solve lots of problem (you will loose ALL your data that are on phone memory (sms/mms, contacts, calendar...) if you're sync to a google account, your contacts and calendar should be preserved)
you may have to perform this to avoid performance issue : here
10/ i own a X10miniPRO (u20i) does this ROM suites to this phone?
NO,No, and No this ROM is ONLY for X10mini (e10i/e10a) not for any other phone [a version is also available for X8, in the X8 section.]
edit : there is a version for minPRO available here so the ROM suites to X10mini, X8 and X10miniPRO in their respective version
11/ my battery is draining so fast ... what should i do ?
first calibrate your battery by fully charging your phone, then reboot into recovery, select Advanced/Wipe Battery Stats and then unplug and reboot
if there's no improvement so far
- see if there's app running always in the background
- look in CyanogenMod settings/Interface/LED notifications/Advanced make sure radom is not ticked
12/ i have installed minicm7 when i power on the phone it stuck on cyanogen 7 logo. what should i do.
does your phone comply to the conditions of the first post ?
if yes and if you can access to CWMrecovery, then reflash the rom and/or factory reset (you will loose ALL your data that are on phone memory (sms/mms, contacts, calendar...) if you're sync to a google account, your contacts and calendar should be preserved)
if not or if you can't access to CWM use Sony Ericsson Update Service to recover your phone as if it was out of the box (you will loose ALL your data that are on phone memory (sms/mms, contacts, calendar...) if you're sync to a google account, your contacts and calendar should be preserved)
13/ in the default input method, when i scroll down/up the "-,?,!,@,_ ..." & emoticons menu until it stops itself, the keyboard remains froozen
rotate your screen and this will be fixed, and don't scroll this violently
14/ app2SD and other features aren't working with 2.0.6, why is that?
for miniCM7 2.0.6 you also need to flash the module hotfix to see all the modules working (oc; uv; app2sd...)
15/
novicebg said:
The radio starts playing on speaker instead of on handsfree.
Click to expand...
Click to collapse
you may first need to choose speaker, and then handfree to route radio correctly (may happen each tile the radio is started...)
16/ i want to install 2.0.7, do I have to install hotfix from 2.0.6?
no you don't : each hotfix is specific of each version
"module hotfix" was for 2.0.6 not 2.0.7
17/ where are market, gmail and other google apps ????
you seem not have read carefully the first post : you need to flash gapps via CWM after flashing the ROM in order to use google services!
18/
mrozilla said:
With CM7 I need a ext partition? I have a standard 2GB card with the X10 MINI and I did not do anything with partitions, is that ok?
Click to expand...
Click to collapse
nAa's first post!!! said:
App2sd / Dalvik2sd compatible with 2.1 app2sd (storing to ext2/3/4 pre-existing partition is detected and mounted as such)
Gingerbread's native App2sd (storing to fat)
Click to expand...
Click to collapse
there is an app2sd storing to FAT feature.
so you don't need any ext partition
but if you have an ext partition on your SD, then it should be used automatically.
19/
hertell said:
Hi folks!
I have tried to find in this thread info on how to enable the sonyericsson version of android market, but i with no luck.
Click to expand...
Click to collapse
hertell said:
I reply to myself after getting help from matmutant.
I was looking for two different things: Getting the Sony Ericsson menu to the market, and enabling the Road Sync app that's free for SonyEricsson X10 mini users
To enable the SonyEricsson market, you need to edit the /system/build.prop file. Please be careful when you edit the file. If you mess up the file, you might get a phone that you can't boot (this can be fixed, cause i messed up a couple fo times I explain this later).
You can either just change the keys, or do like below: comment the old values with a # as the first char on the row, and write the new below.
Code:
#ro.com.google.clientidbase=android-google
ro.com.google.clientidbase=android-sonyericsson
ro.com.google.clientidbase.yt=android-sonyericsson
ro.com.google.clientidbase.am=android-sonyericsson
ro.com.google.clientidbase.vs=android-sonyericsson
ro.com.google.clientidbase.gmm=android-sonyericsson
For enabling the RoadSync app (or i guess any other app that want's to verify that it's running on a real SE-phone), then do these changes:
Code:
#ro.product.model=X10mini
#ro.product.brand=SE
#ro.product.name=robyn
#ro.product.device=robyn
#ro.product.board=robyn
ro.product.model=E10i
ro.product.brand=SEMC
ro.product.name=E10i_1237-0392
ro.product.device=SonyEricssonE10i
ro.product.board=delta
#ro.product.manufacturer=SE
ro.product.manufacturer=Sony Ericsson
As I mentioned earlier, i messed up the /system/build.prop file at one point. To get this fixed, i just rebootet into recoverymode, and mounted /system. After this i could use adb (found in the android-sdk) to copy back an corrected build.prop (./adb push build.prop /system/build.prop)
I had also an other issue with the android-market app. It crashed and got stuck a couple of times, so i fixed this by uninstalling the recent update from manage applications->All->Market.
I hope my changes don't break anything for the CM7, so please if you know that CM7 needs any of these keys i changed in build.prop, then please inform me
Click to expand...
Click to collapse
20/ i can't pull off the notification menu by pressing the bottom of the screen after opening notifications... only for 2.0.7 and previous builds!
it is somewhat hard to close notifications like this (sometime easy sometimes not.) just press back button and all would be fine
regarding 2.1.0+ and custom kernel :
my phone is laggy with 2.1.0 and crashes when screen goes off
it seems that on some phones, lockscreen is related to phone crash:
waiting for a fix,DustArma found a workaround :
DustArma said:
To everyone who has the lockscreen crashing problem, just disable it.
Go to Menu > Settings > CM Settings > Tablet tweaks > Disable lockscreen.
Now it won't freeze, but of course you won't have a lockscreen, that could be fixed by downloading a custom lockscreen from market though
Click to expand...
Click to collapse
DustArma said:
I can confirm that replacement Lockscreens from the market, such as WidgetLocker and Simply Lockscreen will work, so just follow my instructions to disable the lockscreen and then download a replacement one from the market, this will be a good enough workaround until nAa fixes the lockscreen reboot issue some of us are having.
Click to expand...
Click to collapse
---> reported to work. the phone won't freeze anymore, nor need reboots
BETTER WAY : flash miniCM7-2.1.1 that seems to fix the lock screen problem with carrier.
draco_ag said:
21/ I notced weird behaviour of CWM recovery tool.
In some options, e.g wipe cache/factory data or install zip from sdcard i receive otpions like this:
- No
- No
- No
- No
- No
- No
- Yes
- No
- No
Could You fix it please
Click to expand...
Click to collapse
DanielFran said:
This is normal with CWM 4.x, this is to avoid that by mistake you choose YES if it have only 2 options!?!
That way, if you really want to apply YES it will be because you really want....
Click to expand...
Click to collapse
22/ on 2.1.0 & 2.1.1 nAa kernel 02&03, at boot i don't have sony ericsson logo but a blue distorted image instead, is this normal?
bollitodecrema said:
Hi,
I've been loocking in the forum this problem but I can not find it. >>> answered 2000 times, even after the answer being added here.
After unlock the bootloader, when the phone startup show a worng image with blue lines before show the boot animation.
Click to expand...
Click to collapse
yes it is normal, this is a kernel bug, don't worry about that it has been fixed since nAa_kernel 04
when you see that thing it's time to press back button if you want to access recovery
23/ offline charging doesn't work, and my phone boots instead when i plug it to charge, why?
for 2.1.0, 2.1.1, 2.1.2, 2.1.3,2.1.4 & 2.1.5 there is no offline charging due to kernel+cwm (not implemented yet ?), as a result, the phone boots up
fixed with nAa kernel07+miniCM7-2.1.6 !
WestIsland said:
24/ "portable wi-fi hotspot" works fine.
while Charging it keeps connected.
However, when not on charge, the phone turns to sleep and disconnects
Is there a way not to make it keeping connected when idle ?
Click to expand...
Click to collapse
Aerobreaker said:
Settings > Wireless & networks > Wi-Fi settings > Click the left button and choose advanced > Wifi sleep policy > choose never ( i think u chose never when plugged in )
Click to expand...
Click to collapse
waiting for a better answer... this one doesn't change anything since wifi hotspot and wifi are unrelated
for now there is no good answer, this issue should be fixed later
25/ where can i find themes for my mini? (theme chooser themes...)
themes that are fully compatible with our mini are called LDPI so look for LDPI themes !!
here are some themes : pedrocel85 thread
sensified theme : NTsense
sony blue
sony green
CM9 like theme : by ronaldvalles
theme reference : here
flashable theme : black HTC --> WARNING : this destroys stocktheme of CM and takes place instead !!
26/ i'have some problem for sending mms (data enabled) --> with CM7 you just CANT send mms without data enabled
in that case :
DaRk_dOg said:
I think that this is a common issue with CM7 and not just MiniCM7 (I experienced it on my DHD too).
Here is a small workaround for now:
Before sending the mms, disable data traffic, then enable it again and then send your mms.
You have to do it every time, before an mms but it is working for me.
Regards, D_d
Click to expand...
Click to collapse
27/ i need to delete chargemon to boot up to the right recovery but :
arturos1996 said:
i deleted chargemon but cwm 4.x can't mount sdcard!!!! please help!!!!!!
Click to expand...
Click to collapse
--> reboot normally and press back button, do not use the software way of booting to recovery
also try to reboot with the hardware combination : power+back , and then back multipress
each reboot rebuild the chargemon
so each time it fails you need to redelete it
28/ for ext issue, read that :
rogeliodh said:
It is failing to mount sd-ext, script /etc/init.d/05mountsd is failing with:
I/mountsd ( 1160): /dev/block/mmcblk0 not ready, waiting 7 seconds...
I/mountsd ( 1164): /dev/block/mmcblk0 not ready, waiting 6 seconds...
I/mountsd ( 1168): /dev/block/mmcblk0 not ready, waiting 5 seconds...
I/mountsd ( 1172): /dev/block/mmcblk0 not ready, waiting 4 seconds...
I/mountsd ( 1176): /dev/block/mmcblk0 not ready, waiting 3 seconds...
I/mountsd ( 1180): /dev/block/mmcblk0 not ready, waiting 2 seconds...
I/mountsd ( 1184): /dev/block/mmcblk0 not ready, waiting 1 seconds...
E/mountsd ( 1189): SD not found (/dev/block/mmcblk0)
I added the following mknod lines to /etc/init.d/05mountsd:
#!/system/bin/sh
#
# mount ext[234] partition from sd card
mknod /dev/block/mmcblk0 b 179 0
mknod /dev/block/mmcblk0p1 b 179 1
mknod /dev/block/mmcblk0p2 b 179 2
BB="logwrapper busybox";
and it is working now
Click to expand...
Click to collapse
chicco said:
i modified the script and pushed it into the phone with adb: now everything is fixed!!!
this is a small guide:
download android sdk
download the fixed script and unzip it then copy it into the sdcard
launch a command line and To start the SDK Manager, please execute the program "tools/android"
./android
from the graphic menu install the platform tools
after the installal,go in the platform-tool directory and give theese commands
./adb remount
./adb shell
cp /sdcard 05mountsd /etc/init.d/05mountsd
then reboot the phone
now all apps in sd-ext partition are back!
Click to expand...
Click to collapse
here is the file >> direct link
here is the flashable zip (EASY INSTALL)
original fix
go there to thank them :
rogeliodh's post
chicco's post
maxadamo
29/ strange output while unlocking bootloader?
read this (may help you )
30/ after unlocking the BL, my no more recognize the SIM card... What should i do?
DarkestPriest said:
first, if you are not using stock ROM reflash stock ROM&kernel with SEUS then relock, re root etc ...
Click to expand...
Click to collapse
31/ CM native Screenshot doesnt work what can i do?
reboot once or twice
ChavitoArg said:
alternative (not validated for now)
with a root explorer app go to /system/app find CMScreenshot.apk ,
choose Install (replace) ,
system says trough a box: "APP not installed",
then Reboot and voila working again
Click to expand...
Click to collapse
32/ about miniCM7-2.1.2+ :
Kostas1601 said:
Guys I don't see the MIUI battery bar change...how do I apply it???
Click to expand...
Click to collapse
cm settings>interface>status bar tweaks>battery style? option "status bar".
33/ how to edit/delete stuff in /system using rootexplorer?
in the top of rootexplorer there is a button (mount r/w)
touch it, then it will say the /system is mounted as read/write and the button becomes (mount r/o) or something like that
you now can edit the files
34/ if you disabled the bootanimation, the first boot after applying update will seem to be VERY VERY VERY long with a black screen. don't be afraid
for 2.1.6+, when bootanimation is disabled, the kernel bootlogo is displayed instead, after a purple led blinking once
35/ can i apply update 2.1.3 without flashing nAa kernel05 ?
you shouldn't try, 2.1.3 is dependent to kernel05 !
36/ how do i enable USB tether?
settings > wireless and network > network sharing
37/ i've got an issue with SDcard : i can't install the rom since CWMrecovery says that sdcard cannot be mounted !
download sdcard formatter from here and format the sd
then copy/paste update and CWMrecovery should mount sd and install update successfully
(thx to r95)
37b/
Linkinsoldier said:
hi,
my wifi stopped working and i couldn't scan for any wifi!
Click to expand...
Click to collapse
Linkinsoldier said:
i removed my existing network and re-adding them solved the problem!
Click to expand...
Click to collapse
NEXT QUESTIONS ARE POST : #6
________________________
POST #3 : useful links, tweaks & thks
... read all this, again and again,
if this wont be stickied, I will lose hope in mankind
I MADE THIS ONLY FOR X10mini, THIS MAY BE COMPATIBLE WITH X8/X10miniPRO BUT NO TESTS HAVE BEEN PERFORMED YET
1somes usefull links will be added here :
flashtool (use 0.2.9.1)
Flastool last version
SEUS found in MIN thread by dr.norton
optimal config & supercharger (thread by Pedrocel85)
unlock how to
unlock how to 2
what is the use of priority for settings in setcpu?
summary for x10mini/pro
debrick your mini
last chance debrick
miniCM wallpaper by D_d
SD formatter
flashplayer for X10 mini (use the download link for armv6) use it at you OWN risk.
[how to] change X10mini battery
IMPORTANT GUIDE FOR USERS WITH PERFORMANCE PROBLEMS. >>> and here !
Stock kernel for X10 mini ! (not pro)
denoobing, reference and help for x10miniPRO (mimmi) thx to static28
themes that are fully compatible with our mini are called LDPI so look for LDPI themes !!
here are some themes : pedrocel85 thread
sensified theme : NTsense
sony blue
sony green
theme reference : here
...
___________________________________
(nearly)-Safe to remove apps :
yomiguy said:
here is my list:
(these first ones thanks to pedrocel and his optimal config thread)
DSP Manager
Gmail
Google Maps
Latitude
FOTA KILL (gOOGLE OVER THE AIR UPDATES)
Pico TTS (text to speech program/interface - if ypu arent blind u dont need it)
Voice Dial
Voice Search
(these others thanks to bojler in lets free up some memory thread)
androidian - 4MB - useless theme for me, which even isnt ldpi
browser - 320 kb - really bad browser, i use dolphin browser
calculator - i use realcalc
cmstats
cmupdatenotify useful if you want to be notified fr coming updates
cmwallpapers - 2,5MB
cyanbread - 3,6 MB also useless theme
dspmanager - always drains battery in background, and i really havent see any difference in playing music with it
email -1,5 MB - there are better alternatives
file manager - i use rootexplorer
latinime - 13 MB - i dont use this keyboard, its really too hard to use it on our devices, when you delete it, automatically is used standard multitap sony keyboard
livewallpapers - 3,8 MB if you dont use them you can delete this too
livewallpaperspicker you need it if you don't use quickpick ...
orangehaze - 1,7 MB - also, i don't use this theme
protips - that annoying android guy what is providing you tips on first boot after flashing
quicksearchbox 1,0 MB - i also dont use this, on mini pro, when opening keyboard on launcher, that search box launches.
soundrecorder - also, i use different apps for this purpose
genie widget
google books
weather and news (or newspapers, i dont remember the exact name)
an app called car home or something like that...
I think that's all
Click to expand...
Click to collapse
___________________________________
DaRk_dOg said:
Regards, D_d
Click to expand...
Click to collapse
___________________________________
Mrakoris/ said:
There is a demonstration of miniCM7)
Click to expand...
Click to collapse
http://www.youtube.com/watch?v=-5-sxnx62-c
___________________________________
some tests about my config :
Dithering is enabled (wiki) so my performance may be lower than yours
values are reall unstable for each test;
if someone has some time to loose, he can make 10 tests for each settings
theses test have been made with an old version of miniCM7, will be updated later
ondemand
@ max691MHz
7.9MFLOPS
1659 antutu score
@ max600Hz (no UV, no OC)
7.6MFLOPS
1606 antutu score
smartass(v2)
@ max691MHz
8.1MFLOPS
1643 antutu score
@ max614MHz :
7.1MFLOPS
1517 antutu score
@ max600MHz (no OC, no UV)
7.5MFLOPS
1618 antutu score
interactiveX --> this cpu usage policy seems to be the best ratio atm
@ max691 MHz
7.1MFLOPS
1586 antutu score
@ max600MHz (no UV, no OC)
7.5MFLOPS
1550 antutu score
scary : with miniCM7 2.1.3
max CPU clock @691MHz
min CPU clock @122MHz
scary CPU governor
compcache disabled
JIT enabled
dithering enabled
transparency 16bits enabled
purging of assets (bitmap) diabled
home in RAm disabled
SMS/MMS in RAM disabled
VM heap size 32m
SDcard cache size 128kB
no tweaks like supercharged, OOM fixes, compache or anything else enabled
average score : 1782 (using antutu benchmark 2.4.1)
UPDATE:
antutu score : 2000!!@768MHz ondemand
(with no optimization add-on, all animations enabled, dithering, many apps installed and so on : this is not the optimal config for benchmarks...)
some more cool pics :
for more info : follow me on twitter
for battery life i use [email protected], undervolt enabled!
___________________________________
you want to switch quickly between a battery saving mode and performance??
here is a somewhat simple solution >>>> CPU/governor easy and quick switching
it allows you to switch min/max CPUclock, CPU governor and enabling disabling undervolt just by pressing one widget
___________________________________
supercharger optimization that can be usefull :
before updating to newer miniCM,
unsupercharge,
delete supercharger backups and
update to the new miniCM,
then resupercharge if you want
if you don't do that, you may experience some tricky problems if unsupercharging newer miniCM !
if you didn't, ofc don't complain about performance problem
SuperCharger v6 update9-RC1 ONLY for SuperCharger v6 update9 6.2.2 see the middle/end of this post!
first optimization:
1 Download SCRIPT MANAGER FROM MARKET
2 Go to this thread and download SuPERCHARGER SCRIPT 6 update9-RC1
3 Open program, load the script, Tick option run as ROOT.
in program dialog, type "1(fast)" and "enter"
4 answer properly to asked questions by the script !!
5 In main Dialog, type "4" "super UL (aggressive)" and "enter"
6 type 30 (exit) and then "enter" -->at the top you see: running becoming exit code0
7 press "close" (it was "kill" while the script was running)
8 reboot
9 now your phone uses supercharger, you don't need to run it again
another one that seems to be better for our phone (since miniCM7-2.1.3) :
another opti : (i tested and approve this to be somewhat working )
Gustavo RD78 said:
After many tests, I've found the best setting for my phone!
Use only grouping fixes OOM + bulletproof launcher script v6 supercharger, compcache kickasskernelizer standard 18% and tweaks!
The CPU is 600MHz!
I confess that I never had my phone as fast and as stable at the moment!
Back to share more news ...
Click to expand...
Click to collapse
1 Download SCRIPT MANAGER FROM MARKET
2 Go to this thread and download SuPERCHARGER SCRIPT 6 update9
3 Open program, load the script, Tick option run as ROOT.
4 in program dialog, type "1(fast)" and "enter"
5 In main Dialog, type "13" "OOM grouping fixes + bullet proof launcher" and "enter"
6 type 30 (exit) and then "enter" -->at the top you see: running becoming exit code0
7 press "close" (it was "kill" while the script was running)
8 reboot
9 now your phone uses supercharger, you don't need to run it again
then settings > CMsettings > performance > compcache > 18% ; reboot
do NOT use the two at the same time, i recommend the second for better results (at least it is better on my phone)
if you want to undo theses opti :
1 run the script
2 choose 1 (fast)
3 choose 15 (UnSuperCharger)
5 wait
6 type 30 (exit) and then "enter" -->at the top you see: running becoming exit code0
7 press "close" (it was "kill" while the script was running)
8 reboot
9 now your phone uses no more supercharger.
of course, if you have any comment about the tweaks, better tweaks or anything else (e.g comments about the way of introducing the process...), please tell me
____
third opti that yo may want to try :
Mischell53 said:
Good combination with:
Spare Parts program:
Windows Animations FAST
Transition Animations FAST and this script http://forum.xda-developers.com/showthread.php?t=1111145
Compcache 18%
Click to expand...
Click to collapse
___________________________________
things you might want to delete : (but why?)
jorz21 said:
More free space
with rootexplorer /system/usr/zi
delete the languages that you dont need.
system/usr/keyboard-config-languages-delete all languages that you dont need...
/system/fonts delete arabic(1.1mb)fallback(3.47mb)japannese(1.12mb)
/system/media/audio-delete all the sounds that you dont need..
Click to expand...
Click to collapse
___________________________________
Feel free to ask me about adding new answers, or anything that could be useful for users.
this thread is made for this
for my FAQ, i need to say thanks especially to :
Blagus
ChavitoArg
chicco
Dark_dog
Dettofatto
Doixanh
dr.norton
FrenchKoR
Gustavo RD78
Gx3
Linkinsoldier
maxadamo
Maxfron
Mrakoris/
NobodyAtall
Pedrocel85
pollob666
r3drogo
rogeliodh
ronaldvalles
Rooterdam
SpyderX
The_Laser
Yenkazu
yomiguy
...
for their help, their knowledge, or anything else they did that helped me to create this FAQ
and many many others that i can't remember (if i forget some names please notify )
i have done everything fine (unlocked bootloader and installed custom kernel) and made 2nd partition on SD card but when i open LINK2SD i`m getting trouble. sometimes it`s making script but after reboot i need to make script again and again. it can`t mount second partiton. what i have to do to get app2sd working?
Question ???
What is the best that I have to use a custom kernel? Thank you for your attention.
gallardo5 said:
i have done everything fine (unlocked bootloader and installed custom kernel) and made 2nd partition on SD card but when i open LINK2SD i`m getting trouble. sometimes it`s making script but after reboot i need to make script again and again. it can`t mount second partiton. what i have to do to get app2sd working?
Click to expand...
Click to collapse
from which rom did you upgrade ?
I don't really understand why do you use link2sd since this feature is embedded in the rom ...
you should better delete the content of the ext partition and use gb app2sd feature
______________________________________
FAQ second part since there's a max number of letters(...) per posts
38/
novicebg said:
The Sound icon on the Taskbar does not switch on and off the sound - it doesn't change the phone's state to silent, only vibrating, ringing or ringing with vibration. The other 3 icons work well - the BT, Wi-Fi and the GPS switch on and off with no problem, but the Sound and vibration... Why is that?
Click to expand...
Click to collapse
ronaldvalles said:
settings > CyanogenMod Settings > Interface > Notification widget status bar i.e option 2 ("gestion de alimentation" in French) , > widget buttons (i.e option7),
scroll nearly to the end to find sound (ring) modes,
tick the options you need, then accept
now it should work
Click to expand...
Click to collapse
if you have problem with any widget button try a similar solving way
39/ if you have any problem with flashing using flashtool, theses posts may help you :
original explanation by hakanyildiz
rephrased by alex_gm
40/ why do i have an annoying pop up asking for unlock key when i boot up my phone?
ferotakis said:
after little talk with one my friend we figure it out why in some provider is asking this code and in some not( like my case)
The reason is: This ROM is not legal I mean the original one from the Sony who before opening to users in theirs regions firs will be sent to operators , operators check it and then when you use for example Vodafone.de Vodafone.de if aprove the Sony ROM send a notification to users for a update is ON. When users updates their phone with the operator passed ROM they can be ''seen'' by the operator what type of phone with what type ot Android they are use and can send them auto setings like the APN MMS and etc.
If you want see the truelles of this just call your operator and ask them for auto APN . Try it if you have x10 mini with stock rom and with x10 mini with this one
In firs one operator say you : Ok i see in system you are using x10 mini vith android 2.1 i will send you the setings . But with this room she/he ask you what type of phone do you use bicoz I cant see it on system.
This is same wit the automated operator menus too : when you pres 4 (for example ) in voice menu and ask for a auto internet setings the autovoice say sorry we not support you phone yet will try again later.
This is not big deal for now bicoz the most of operators APN is already configuret but if you use operator who is not includet you cant use mobile data bicoz you not have APNs.
That is wy this code is asking for when you put some of providers sim some of them make theirs system in that way ... its more easy for them but for us is just annoing popup window
Click to expand...
Click to collapse
>>> thk him for this please
41/ how can i disable the network lock dialog after pin input? (miniCM7-2.1.5)
to disable the network lock dialog after pin input, add this line at the end of your build.prop (/system/build.prop)
Code:
ro.telephony.ril_skip_locked=true
then reboot
to re-enable change the value to "false", or delete the line
how to : use rootexplorer,
go to the right place,
then long press on the file,
choose "open in text editor" in the scrolling menu
and add the line at the end of the file
42/
TrissyGE said:
What are ETA´s?
Click to expand...
Click to collapse
phoneyericsson said:
ETA: Estimated Time of Arrival i.e. when something is expected to arrive/be finished.
Click to expand...
Click to collapse
43/
BééHach said:
i can't find my wifi network but some other are discovered by the phone, how to fix it?
Click to expand...
Click to collapse
Go to Settings > Wireless & Networks > Wi-Fi Settings and press the menu button.
Choose 'Advanced' and in the 'Regulatory domain' option, change the number of channels from 11 to 14.
44/ you feel wrong with autobrightness ?
maybe this can help you (i did not try, i prefer not to but instead of flashing blindly, open it and see what has changed )
45/ problem with google precache?
nussbaum said:
Hi to denlille and all others,
to get Google Maps Precache working with x10mini / e10i
edit your /system/build.prop and add
Code:
ro.opengles.version=131072
I added that line above ro.com.google.locationfeatures=1
- reboot after editing and maybe
- delete app data of maps
Here is the link of the thread i found it:
http://forum.xda-developers.com/showthread.php?t=1158183
Click to expand...
Click to collapse
46/ if you have a instable connection, you may read the following
ChavitoArg said:
Hi everyone, my 3g conection was really unstable and i delete this lines in build.prop:
ro.ril.hsxpa=2
ro.ril.gprsclass=10
ro.ril.hsupa.category=5
Now my data start inmediatly and the conection is stable again.
Ps: it may not work for all, because my 3g works on other freq bands.
Click to expand...
Click to collapse
ChavitoArg said:
47/ What is exactly WLOD? :?
Click to expand...
Click to collapse
it is the led that turns on in white when a kernel panic happens (unix's BSOD [Blue Screen Of Death that happens on windows when a critical hard/software error happens and needs the system to freeze to prevent a data loss)
White Led Of Death is meant to help to see from where comes the bug (i.e. if it comes from kernel : white led!)
some more precisions about the LED : here !
48/ concerning wifi, if it stops working at all, first try to delete wpa_supplicant.conf in data/misc/wifi or read Qs 24, 37b and 43
49/
Dualtouch:
If you want to enable the fake DT by dx (instead of andrej456's which is the default), you have to insert the following line in the /system/etc/hw_config.sh file:
insmod /system/lib/modules/synaptics_i2c_rmi4_dt.ko
If you want to remove the fake DT altogether, insert the following line in the /system/etc/hw_config.sh file:
insmod /system/lib/modules/synaptics_i2c_rmi4_no_dt.ko
aloy99 said:
50/ Hmm... So the new a2sd is essentially data2ext? Will I have problems upgrading as I'm on ext2, which is not supported?
Sent from my E10i using XDA App
Click to expand...
Click to collapse
nobodyAtall said:
Here's a brief explanation for A2SD/DC2SD/Swap:
A2SD/DC2SD only makes sense if you have /data that is over 200MB i.e. many apps.
Swap is useful if you need to run memory-hungry apps or wanna have more apps loaded in memory.
Any size for swap should be good depending on your needs (e.g. 128MB). To verify a2sd is loaded, run df via adb shell. It should show /data/app and /data/app-private mounted in /sd-ext.
Also /data/dalvik-cache should be mounted to /sd-ext/dalvik-cache if DC2SD is chosen.
To verify swap is used, try the command 'free' via adb shell.
None of the above are for the everyday/novice users. You have to know what you are doing.
Click to expand...
Click to collapse
51/ A2SD, WTF? (bis)
todonormal said:
explanation of http://forum.xda-developers.com/showthread.php?p=22505939#post22505939 for dummies:
A2SD
What is a2sd?
It's other metod to save applications in SD.
How prepare your SD?
In Windows: Use http://www.partitionwizard.com/free-partition-manager.html or other tool partition. Create a ext4 partition in your SD.
In Ubuntu: Use gparted for create ext4 partition
How activate? (thanks to ferotakis)
1. Format SD and partiton it with CWM on phone make yor ext part and swap if yo want swap ig not live it 0
2. Install minicm7
3. Go to CM seting under performance put the a2sd (first show none till reboot)
4. Go to CM then hit apps and tick the "allow app moving to external "
5. Open terminal and type free
6. Go to CM again then performance again then to a2sd and chek there must no say NONE and must be a2sd
7. Install some apps then rootexplorer and browse in root dir on your phone you will saw ext folder open it and look your apps will be there
8. Thanks again if you missed to NAa
9. Learn some Linux
10. Go outside and show your fr and bbf your amazing phone
Click to expand...
Click to collapse
Hey my friend,
Can you see if this thread is worty to enter en the FAQ.:
CM7 Configuration Thread:
http://forum.xda-developers.com/showthread.php?p=17714446#post17714446
best,
pedrocel85
pedrocel85 said:
Hey my friend,
Can you see if this thread is worty to enter en the FAQ.:
CM7 Configuration Thread:
http://forum.xda-developers.com/showthread.php?p=17714446#post17714446
best,
pedrocel85
Click to expand...
Click to collapse
of course i will
i'm currently testing some governors with or without OC/UV i'll post them later
matmutant said:
from which rom did you upgrade ?
I don't really understand why do you use link2sd since this feature is embedded in the rom ...
you should better delete the content of the ext partition and use gb app2sd feature
Click to expand...
Click to collapse
i updated from MiniCM7 2.0.7. and I want to use link2sd because i`m installing a lot of apps on the phone and i need them to still work when i`m mounting SD Card to the PC. i`m trying to make it work from about 3 days but still nothing
gallardo5 said:
i updated from MiniCM7 2.0.7. and I want to use link2sd because i`m installing a lot of apps on the phone and i need them to still work when i`m mounting SD Card to the PC. i`m trying to make it work from about 3 days but still nothing
Click to expand...
Click to collapse
but if you create an ext partition, it should be recognized by GB native app2sd... and you will be able to only mount fat part of your sd .. no?
matmutant said:
but if you create an ext partition, it should be recognized by GB native app2sd... and you will be able to only mount fat part of your sd .. no?
Click to expand...
Click to collapse
i moved GMail with native GB app2sd but when i`m mounting SD Card to PC GMail and another apps are stopping to work
edit: i`m not sure to which partition native GB app2sd is moving apps but i tried to do this with ext2,3,4 and FAT32 and it didn`t work with any of them
new links added
any request, questions&answers, etc... are awaited
matmutant said:
new links added
any request, questions&answers, etc... are awaited
Click to expand...
Click to collapse
maybe make a tutorial how to set the link2sd properly?? I think that will be usefull because some people have the same problem like me
gallardo5 said:
maybe make a tutorial how to set the link2sd properly?? I think that will be usefull because some people have the same problem like me
Click to expand...
Click to collapse
since i don't know the answer atm ... i can't
matmutant said:
since i don't know the answer atm ... i can't
Click to expand...
Click to collapse
awwww ok so I need to wait but it`s worth this. and by the way are you using link2sd on your phone?? if yes what type of partition are you using??
gallardo5 said:
awwww ok so I need to wait but it`s worth this. and by the way are you using link2sd on your phone?? if yes what type of partition are you using??
Click to expand...
Click to collapse
i'm using GBapp2sd storing to fat feature
so no partition, only one main partition on the sd card
matmutant, perfect!
Delete the question.
RoTiV- said:
matmutant, perfect!
Click to expand...
Click to collapse
you can try to posh the thank button if you think my work is worth the click
have a nice day
hey mat, check out this script, already added in my optimal configuration thread:
Supercharger v8 Memory optimize script.
1 Download SCRIPT MANAGER FROM MARKET
2 Go to this thread and download SuPERCHARGER SCRIPT
3 Open program, load the script, Tick option set on boot.
4 in program dialog, type "1(fast)" and "enter"
5 In main Dialog, type "2" agressive one" and "enter"
6 Hit back button, click in run in background.
7DONE
I am not responsible for bricked devices,
This is a port of Ubuntu Touch for the LG V20 T-Mobile h918 variant. Not yet stable.
Before install halium-boot.img backup only your boot partition. You can restore your current system after try Ubuntu touch. Ubuntu touch will be install in data partition not in system partition.
Youtube :
Sources:
Kernel:
https://github.com/walidham/android_kernel_lge_msm8996/tree/halium-7.1
Device:
https://github.com/walidham/android_device_lge_h918/tree/halium-7.1
https://github.com/walidham/android_device_lge_msm8996-common/tree/halium-7.1
Manifest file
https://github.com/walidham/lge_manifest/tree/master
Status
Working:
Audio
Calling
SMS
4G
Wifi
GPS
Vibration
Orientation sensor
Missing:
Video recording/decoding
Bluetooth
Flash light
ADB/MTP
Libertine
camera
fingerprint
There are two methods to install Ubuntu Touch
Method 1 : unofficial installation with TWRP
1- Download zip file UT TWRP
2- push it in internal storage or sdcard
3- backup up your current boot partition (to restor it later if you want return to android rom)
4- install zip file, make sure your data partition is ext4 (option if you want fresh install you can wipe data partition)
5- rebbot
Note : password is "1111"
Method 2 : official installation/ hard for newbie
NOTE: As the LGV20 aren't community devices yet, the install process may be a little "non-noobie-friendly"
Install twrp on your device, format data partotion to ext4
Download the latest precompiled system.img and halium-boot.img from : halium-boot
Download the JBB's halium install script
Download either the regular rootfs or the Edge one
While on TWRP:
Code:
halium-install -p ut the_rootfs_you_choose.tar.gz system.img
While on TWRP:
Code:
adb shell 'mkdir /a; mount /data/rootfs.img /a; echo manual | tee /a/etc/init/rsyslog.override; umount /a; sync'
While on TWRP: install halium-boot.img (on boot partition)
Then reboot
Connect to phone with ssh
Code:
ssh [email protected]
When entering in ssh run those commands:
Code:
$ sudo -i
$ mount -o remount,rw /
$ cat /var/lib/lxc/android/rootfs/ueventd*.rc | grep ^/dev | sed -e 's/^\/dev\///' | awk '{printf "ACTION==\"add\", KERNEL==\"%s\", OWNER=\"%s\", GROUP=\"%s\", MODE=\"%s\"\n",$1,$3,$4,$2}' | sed -e 's/\r//' >/etc/udev/rules.d/70-h918.rules
$ reboot
If you want suport this project you can donate
Edited : 03-09-2022 :
Now H910 is supported,
For LG V20, i finished the port for H910, its beta version need more test and fixe bugs.
Download link : https://www.androidfilehost.com/?fid=14871746926876820212
Installatio:
1- backup your data and boot partition. System partition you can take it, we not use it.
2- Download ubuntu-touch-h910-01-01-2020.zip
3- Install the zip
4- Rebbot
excellent sir
Got Camera work, but without video record, just take photo on 12mb max
i want to try ubuntu. can you make more detail about instal ubuntu.
because in step 1 . always like this
not found.
thank you
Tried
Very little would need to be fixed to get me to use this ROM full time. GREAT WORK!!!!!!
Excited to see this rom/OS take off. Got this loaded on my phone, love the OS, but found a few issue (might be my fault).
Slow but mostly usable.
Can't use keyboard in Settings > Accounts. Configuring NextCloud, can't type anything in at all. Would have been way more usable if i could configure the accounts.
Other places didn't toggle keyboard when selecting a text field.
If anyone else is or is not having those issue, please let me know as I might have done something wrong.
Calls, messaging, tethering all work great
Is there a debug that Ubuntu Touch uses. Doesn't look like it uses JournalCTL. I would like to see the issue in the debug if possible to see if there is a way i can help.
AGAIN, GREAT WORK!!! AMAZING STUFF!!!
nickhaven said:
Very little would need to be fixed to get me to use this ROM full time. GREAT WORK!!!!!!
Excited to see this rom/OS take off. Got this loaded on my phone, love the OS, but found a few issue (might be my fault).
Slow but mostly usable.
Can't use keyboard in Settings > Accounts. Configuring NextCloud, can't type anything in at all. Would have been way more usable if i could configure the accounts.
Other places didn't toggle keyboard when selecting a text field.
If anyone else is or is not having those issue, please let me know as I might have done something wrong.
Calls, messaging, tethering all work great
Is there a debug that Ubuntu Touch uses. Doesn't look like it uses JournalCTL. I would like to see the issue in the debug if possible to see if there is a way i can help.
AGAIN, GREAT WORK!!! AMAZING STUFF!!!
Click to expand...
Click to collapse
Can you tell to me how to Input step 1 in twrp?
In my device every want to input halium-boot always not found
nickhaven said:
Very little would need to be fixed to get me to use this ROM full time. GREAT WORK!!!!!!
Excited to see this rom/OS take off. Got this loaded on my phone, love the OS, but found a few issue (might be my fault).
Slow but mostly usable.
Can't use keyboard in Settings > Accounts. Configuring NextCloud, can't type anything in at all. Would have been way more usable if i could configure the accounts.
Other places didn't toggle keyboard when selecting a text field.
If anyone else is or is not having those issue, please let me know as I might have done something wrong.
Calls, messaging, tethering all work great
Is there a debug that Ubuntu Touch uses. Doesn't look like it uses JournalCTL. I would like to see the issue in the debug if possible to see if there is a way i can help.
AGAIN, GREAT WORK!!! AMAZING STUFF!!!
Click to expand...
Click to collapse
try to fix display scalling
1- when system boot connect to the phone via ssh
ssh [email protected]
Code:
sudo -i
cd /etc/ubuntu-touch-session.d
nano h918.conf
add this lines
Code:
GRID_UNIT_PX=29
QTWEBKIT_DPR=2.5
NATIVE_ORIENTATION=portrait
FORM_FACTOR=handset
save file and reboot
For debug
Code:
cat /var/log/syslog
dmesg
sudo /system/bin/logcat
raf21 said:
Can you tell to me how to Input step 1 in twrp?
In my device every want to input halium-boot always not found
Click to expand...
Click to collapse
in twrp, select install -> clique button install image (at the bottom)
select halium-boot.img (you must copie from pc to your phone)
walidham said:
in twrp, select install -> clique button install image (at the bottom)
select halium-boot.img (you must copie from pc to your phone)
Click to expand...
Click to collapse
To input halium-install, use terminal in twrp ? Or use terminal in pc.
Sorry for my english
raf21 said:
To input halium-install, use terminal in twrp ? Or use terminal in pc.
Sorry for my english
Click to expand...
Click to collapse
Look at halium-install link
halium-install is done on a linux pc/livecd/virtual machine that has the following installed
qemu-user-static
qemu-system-arm
e2fsprogs
simg2img
sudo
binfmt-support
Looks like it asks for the phone to be connected via usb as well.
Phoenix591 said:
Look at halium-install link
halium-install is done on a linux pc/livecd/virtual machine that has the following installed
qemu-user-static
qemu-system-arm
e2fsprogs
simg2img
sudo
binfmt-support
Looks like it asks for the phone to be connected via usb as well.
Click to expand...
Click to collapse
i noob in linux
can you make step for install this .... please
iam very interest in ubuntu touch
raf21 said:
To input halium-install, use terminal in twrp ? Or use terminal in pc.
Sorry for my english
Click to expand...
Click to collapse
1- reboot to recovery
2- connect your phone to pc (system ubuntu must be)
3- copy halium-boot.img to interal storage of phone
4- run halium install script
Code:
ex : ./halium-install -p ut ubuntu-touch-hybris-xenial-edge-armhf-rootfs.tar.gz system.img
5-install halium-boot.img with twrp
walidham said:
1- reboot to recovery
2- connect your phone to pc (system ubuntu must be)
3- copy halium-boot.img to interal storage of phone
4- run halium install script
Code:
ex : ./halium-install -p ut ubuntu-touch-hybris-xenial-edge-armhf-rootfs.tar.gz system.img
5-install halium-boot.img with twrp
Click to expand...
Click to collapse
how to run script
every i take halium script in terminal ubuntu always
/home/alienware/Desktop/ubuntu touch/halium-install-master/halium-install.sh' -p
Unsupported post install release! Exiting now
maybe i will try again if anybody can tell to me complete step by step to install ubuntu touch
thank for porting to ubuntu touch to h918
raf21 said:
how to run script
every i take halium script in terminal ubuntu always
/home/alienware/Desktop/ubuntu touch/halium-install-master/halium-install.sh' -p
Unsupported post install release! Exiting now
maybe i will try again if anybody can tell to me complete step by step to install ubuntu touch
thank for porting to ubuntu touch to h918
Click to expand...
Click to collapse
make dot and slash before commande like this ./halium-install.sh
youtub : https://youtu.be/E2FtIR7SUYU
Any chance that this would come to the other LG V20's such as the L997 (sprint)?
Americancosworth said:
Any chance that this would come to the other LG V20's such as the L997 (sprint)?
Click to expand...
Click to collapse
I have just h918, but i can build UT for others variant and i need tester for it.
walidham said:
I have just h918, but i can build UT for others variant and i need tester for it.
Click to expand...
Click to collapse
Can you help me to build Ubuntu touch for us998 lg v30 sir
raf21 said:
Can you help me to build Ubuntu touch for us998 lg v30 sir
Click to expand...
Click to collapse
for help you can join us at telegram
https://t.me/ubports_porting
unofficial installation with TWRP
1- Download zip file UT TWRP
2- push it in internal storage or sdcard
3- backup up your current boot partition (to restor it later if you want return to android rom)
4- install zip file, make sure your data partition is ext4 (option if you want fresh install you can wipe data partition)
5- rebbot