I bought a used Vibrant on eBay, and it came with a broken piece of glass on the camera. It had a nice little 'Y' shape right in the middle that caused a nasty glare in any pictures with a light source shining on it. So I looked at the site known for selling the front-facing cameras, and sure enough, they have the camera glass as well:
http://www.globaldirectparts.com/Samsung-S-i9000-Camera-Lens-p/smsng6087120.htm
Unfortunately, they've also got a min quantity of 5, and more shipping than is strictly necessary, turning my $3 part into a $30 part. So, long story short, I've got 3 extra camera lenses (I'm keeping an extra one, just in case). Anyone want them? I'm thinking $7 a piece shipped in a normal envelope would work. PM if interested. All sold. Feel free to post here if you do a min buy and need to sell extras
For posterity, here's how to do it (though it's pretty obvious once you try):
1. Open the back according to the instructions in the hardware GPS fix thread (you may want to do the GPS fix at the same time, if you haven't already). I found it easiest to start prying the back off from the bottom of the side with the power button, and then work around the bottom to the other side, and the up.
2. Looking at the inside of the back piece, remove the black sticker from around the camera glass bezel's feet. See picture 2.
3. Pry up the 3 metal feet of the camera glass bezel so that they stand as straight up as you can get them. See picture 3.
4. Flip the back piece over so that you can see the bezel, and pop it off. Underneath where it was, the glass is adhered to the back. Gently but firmly pry it off. See picture 4.
5. Replace the glass, stick the bezel back on, flip it over and bend out the bezel feet again, put the sticker back on, and reassemble the phone.
Easy.
I've gotten one nibble...anyone else?
Sent from my SGH-T959 using XDA App
Pm'd you. Thanks
Subscribed thanks for the info!!
Sent from my SGH-T959 using XDA Premium App
If anyone has 1 extra, I wanna buy one off you!
Camera lens just broke, need a replacement!
So I dropped my SGS and unsurpisingly the camera lens cracked. Thanks for putting up this tutorial on how to replace the lens though, as I've been looking for something like this for a while.
Any chance you still have any extra lenses? If not I may just buy 5 and then see if anyone else needs the others as you've done.
Cheers!
I'm all out now, I even sold the one I was thinking of keeping as extra. I guess it took about two months to sell them, but I did eventually. Someone else needs to bite the bullet now
I may just bite that bullet. Wondering if anyone else here would need some. I see 1-2 peeps so far
Sent from my SGH-T959 using XDA Premium App
I'm in for one. Let me know if you decide to purchase.
I'll buy them today. I'll post back in this thread when they arrive and let interested parties know how to get your hands on one.
OP - How long did delivery take when you ordered?
rfdub said:
I'll buy them today. I'll post back in this thread when they arrive and let interested parties know how to get your hands on one.
OP - How long did delivery take when you ordered?
Click to expand...
Click to collapse
Please put me down for one. Thanks.
I don't remember it taking too long...
Think he bailed...
Hey, I might be in for one as well. I was the guy that bought the last remaining one from OP, but It might be lost in the mail. I was going to wait it out a few more days and then find a new source.
If u find a new source, please post a link. Ive searched for days and couldn't find anything.
I haven't purchased the lens covers yet as I'm having a pretty strong moral objection to the shop wanting to charge $35 dollars to ship 5 tiny pieces of plastic to me.
I hate these bloody "shipping and handling" scammers and don't really want to give them any of my money.
I'm still looking for other options and will post if I find anything.
SIGH* searched all over, can't find anywhere that sells this one piece.
an alternative is to buy the backplate housing which includes the lens piece, but that wouldn't be a cheap solution.
suchavibrantthang said:
SIGH* searched all over, can't find anywhere that sells this one piece.
an alternative is to buy the backplate housing which includes the lens piece, but that wouldn't be a cheap solution.
Click to expand...
Click to collapse
My suggestion would to just be buy the lot and put the ones you dont use on ebay... I'm sure somewhere out there someone also needs this pieces. Yeah your not gonna get your money back right away ... but hey you can jack up the price 5 bucks and make some money off someone hahaha
has anyone took one for the team yet?...
I had a very messed up camera lens. Bought a phone from ebay with an unusably scratched camera lens. Used a nail buffer. it took a lot of elbow grease and I rounded it off a bit, but the camera doesn't seem to be distorted and now work perfectly.
used one like this:
http://www.amazon.com/gp/product/B0..._m=ATVPDKIKX0DER&pf_rd_r=0PAX4CKESB6JYP1QTJEP
first you start with the coarse side. you have to work at it for a while. there will be a shrinking circle in the middle of the lens that buffer can't get to at first. you have to work at it for like 10 min to resurface the entire area. Once you've roughed up the whole lens move on to the next finer side... work all 4 sides for about 5 min each, or so... and you should be good.
wet sanding would probably work better... but this is a pretty damn good fix using something you probably already have laying around the house.
Related
I have been using my T-Mobile TP2 without protection on it for a while and have dropped it a few times. The screen is still perfect and the lower half (keyboard) has relatively no damage other than a few spots of chipped paint.
But the upper half, around the edges, has took quite a bit of damage. Mostly chipped pieces and dents, partially because of me dropping it and also because the bodyguard I was using previously damaged it! It was one of those crappy snap-on ones. Will never get one again, just bought ghost armor.
Anyway my question is what is the best way to repair the chipped pieces and dents or is that piece sold somewhere so I could replace it? I have no experience replacing things on the phone but I'm sure if there's a tutorial anywhere it wouldn't be too hard for me. Besides I"m not trying to disassemble the entire thing just the upper portion without the screen.
Any help appreciated.
Showtime7 said:
I have been using my T-Mobile TP2 without protection on it for a while and have dropped it a few times. The screen is still perfect and the lower half (keyboard) has relatively no damage other than a few spots of chipped paint.
Deleted stuff...
Any help appreciated.
Click to expand...
Click to collapse
Best option...Ebay>buy broken (software wise) TP2>use if for spare parts
hmmm the only cheap one I could find listed was also worn...
was hoping to profit because i will probably be selling my TP2 soon.
go to ebay and search touch pro 2 houseing case there about 80 bucks they come in balck and red and black and blue the are a little hard to swich over to but i did it and it worked out fine just takes about an hour tools and dremal if and only if ure useing the tp2 t7373
I am trying to locate a replacement front HW button (back key is either cracked or scratched and light shows through) - so, during the lcd repair process, is this button easily replaceable without getting too involved with any other components? Any suggestions or advice on what to do/where to locate this piece of plastic would be met with extreme gratitude!
Get a new housing from eBay.
Just be careful to get one that fits your version.
My phone was stolen at work on Friday, so I managed to scramble and find one at a good price on eBay and it arrived this morning.
While I did ask to see photos, and I expected some scuffs, the photos didn't do the device justice at all, as it's much worse than I expected. In all the time I've owned my devices, I've never dropped my phone once, not once! this thing's a disaster.
So I'll need to get a replacement housing. I've been looking at eBay but couldn't see anything except these ridiculous colored housings for teens and 20-somethings. Where do real adults get the housings from?
This is an excellent outer shell protector, gives better heft holding (IMHO), rubberized black, very lightweight. Just snaps on and off.
Auction ended, but locate seller store. My Tilt2 fit perfectly in the Touch Pro Verizon except camera button needed cutting shell (trivial task).
http://cgi.ebay.com/HTC-TOUCH-PRO-2...D-COVER-CASE-/130412358305?pt=PDA_Accessories
PDADoc said:
My phone was stolen at work on Friday, so I managed to scramble and find one at a good price on eBay and it arrived this morning.
While I did ask to see photos, and I expected some scuffs, the photos didn't do the device justice at all, as it's much worse than I expected. In all the time I've owned my devices, I've never dropped my phone once, not once! this thing's a disaster.
Click to expand...
Click to collapse
You could take it up with eBay for SNAD, probably get a refund depending on the exact wording of the add, but if it was really SNAD should do it.
So I'll need to get a replacement housing. I've been looking at eBay but couldn't see anything except these ridiculous colored housings for teens and 20-somethings. Where do real adults get the housings from?
Click to expand...
Click to collapse
Eh? On ebay? You have everything from the original HTC version to various carrier variations, search more/wider. They're 40-80$ though.
kosmarnik said:
You could take it up with eBay for SNAD, probably get a refund depending on the exact wording of the add, but if it was really SNAD should do it.
Eh? On ebay? You have everything from the original HTC version to various carrier variations, search more/wider. They're 40-80$ though.
Click to expand...
Click to collapse
I've been checking but I haven't found anything but these colored replicas and I don't want that. I'm willing to pay more for the original housing if I could find it.
As for the eBay complaint issue, I did think about it, but eBay is such a PITA about any disputes; they always act as though they don't want to get involved at all. In the end, I'll eat this one caveat emptor, at least this time.
PDADoc said:
I've been checking but I haven't found anything but these colored replicas and I don't want that. I'm willing to pay more for the original housing if I could find it.
Click to expand...
Click to collapse
Sorry man, but lern2internet. It's the first 4 hits on ebay. Just enter "htc touch pro 2 housing" and check 'worldwide'.
As for the eBay complaint issue, I did think about it, but eBay is such a PITA about any disputes; they always act as though they don't want to get involved at all. In the end, I'll eat this one caveat emptor, at least this time.
Click to expand...
Click to collapse
eBay dispute process is tedious an long winded, but will lean towards the buyer in almost all cases. You just have to be patient.
PDADoc said:
As for the eBay complaint issue, I did think about it, but eBay is such a PITA about any disputes; they always act as though they don't want to get involved at all. In the end, I'll eat this one caveat emptor, at least this time.
Click to expand...
Click to collapse
Always pay with your credit card through PayPal. Ebay and PayPal suck at disputes; your credit card company is your fall-back and your best protection as well.
You can get OEM housings for $50-60:
http://www.parts4repair.com/products/Housing-for-HTC-T7373.html
Looks like it's kinda tricky to replace the housing (if you're going OEM)....
http://pocketnow.com/hardware-1/htc-touch-pro2-disassembly-assembly-training-videos
PDADoc said:
I've been checking but I haven't found anything but these colored replicas and I don't want that. I'm willing to pay more for the original housing if I could find it.
As for the eBay complaint issue, I did think about it, but eBay is such a PITA about any disputes; they always act as though they don't want to get involved at all. In the end, I'll eat this one caveat emptor, at least this time.
Click to expand...
Click to collapse
On ebay? i suggest amazon.
rete said:
Always pay with your credit card through PayPal. Ebay and PayPal suck at disputes; your credit card company is your fall-back and your best protection as well.
You can get OEM housings for $50-60:
http://www.parts4repair.com/products/Housing-for-HTC-T7373.html
Looks like it's kinda tricky to replace the housing (if you're going OEM)....
http://pocketnow.com/hardware-1/htc-touch-pro2-disassembly-assembly-training-videos
Click to expand...
Click to collapse
Great, thanks for the tip! I'll have to look into this closer, as I think if I go with the Touch Pro 2 OEM housing, there'll be a hole for the front-facing camera.
Maybe I'll just deal with it for now and keep my eyes open for an AT&T Tilt 2 housing somewhere. If it wasn't so beat up, I'd try a warranty exchange through AT&T; I was able to do it when I purchased a used BlackBerry Bold 9700 with no problem.
Can use HTC TP2 housing on T-Mobile TP2?
PDADoc said:
Great, thanks for the tip! I'll have to look into this closer, as I think if I go with the Touch Pro 2 OEM housing, there'll be a hole for the front-facing camera.
Maybe I'll just deal with it for now and keep my eyes open for an AT&T Tilt 2 housing somewhere. If it wasn't so beat up, I'd try a warranty exchange through AT&T; I was able to do it when I purchased a used BlackBerry Bold 9700 with no problem.
Click to expand...
Click to collapse
Hi there!
I've a T-Mobile Touch Pro 2 that is quite beat up too & I want to replace the whole housing.
Problem is where I'm living right now, the T-Mobile housing costs double of the standard Touch Pro 2 housing.
Is it possible to fit the motherboard, flex cable & LCD panel of the T-Mobile onto a HTC Touch Pro 2 casing with the power button?
I would need the touch screen & call/navigation buttons as well.
Please advise me if you know anything about this.
Thanks!
Konker
I'm afraid I don't know myself, but if you keep searching, I'm sure there is someone who's done it and knows for sure.
Take a look at this thread: http://forum.xda-developers.com/showthread.php?p=8580850#post8580850
So i've been an Atrix owner for about 2 weeks now and my worst nightmare happend today. I was buying a drink from a vending machine and the phone slipped out of my pocket and fell SCREEN FIRST onto concrete.
I quickly picked it up and noticed THERE WAS A HUGE CRACK in the screen!
I AM SO SAD RIGHT NOW cause i bought the atrix outright from AT&T
i dont think the LCD panel itself was damaged but the glass on the surface only. The display looks perfectly fine still so i was curious if anyone knows how to switch out the glass part? What tools do i need?
I found this one ebay:
http://cgi.ebay.com/Motorola-MB860-...838?pt=LH_DefaultDomain_0&hash=item588d7db4fe
is this the right part?
or do i have to buy the entire LCD, cause its much more expensive:
http://cgi.ebay.com/AT-T-MOTOROLA-A...507?pt=LH_DefaultDomain_0&hash=item33666a4883
also, does anyone know any reputable sellers that sell LEGIT parts such as the digitizer? I'm not sure if i can trust these random ebay sellers...any suggestions would be appreciated
i attached some pictures to show you what happend - i still can't believe it happend
i'm also really surpirsed the gorilla glass broke so easily. The drop was at MOST 1.5 feet..
Bakedbread said:
So i've been an Atrix owner for about 2 weeks now and my worst nightmare happend today. I was buying a drink from a vending machine and the phone slipped out of my pocket and fell SCREEN FIRST onto concrete.
I quickly picked it up and noticed THERE WAS A HUGE CRACK in the screen!
I AM SO SAD RIGHT NOW cause i bought the atrix outright from AT&T
i dont think the LCD panel itself was damaged but the glass on the surface only. The display looks perfectly fine still so i was curious if anyone knows how to switch out the glass part? What tools do i need?
I found this one ebay:
http://cgi.ebay.com/Motorola-MB860-...838?pt=LH_DefaultDomain_0&hash=item588d7db4fe
is this the right part?
or do i have to buy the entire LCD, cause its much more expensive:
http://cgi.ebay.com/AT-T-MOTOROLA-A...507?pt=LH_DefaultDomain_0&hash=item33666a4883
also, does anyone know any reputable sellers that sell LEGIT parts such as the digitizer? I'm not sure if i can trust these random ebay sellers...any suggestions would be appreciated
i attached some pictures to show you what happend - i still can't believe it happend
i'm also really surpirsed the gorilla glass broke so easily. The drop was at MOST 1.5 feet..
Click to expand...
Click to collapse
Yea, thats not a bad deal. You could use DealExtreme though if you wanted. But this seems like a good deal.
Teardown Video.
http://www.youtube.com/watch?v=TbR56jSplRs
Watched a bit and it looks like a good tutorial.
Also, if you don't have the tools you might want this kit.
http://cgi.ebay.com/Motorola-MB860-...195?pt=LH_DefaultDomain_0&hash=item2310051643
It's about the same price and those are both going to ship from Hong Kong. So expect a wait. I didn't find any sellers in the U.S.
There are some that would ship from the U.S. without tools but the price is more like fifty bones instead of 30 something.
Good Luck
JdgM3NT4L said:
Teardown Video.
http://www.youtube.com/watch?v=TbR56jSplRs
Watched a bit and it looks like a good tutorial.
Also, if you don't have the tools you might want this kit.
http://cgi.ebay.com/Motorola-MB860-...195?pt=LH_DefaultDomain_0&hash=item2310051643
It's about the same price and those are both going to ship from Hong Kong. So expect a wait. I didn't find any sellers in the U.S.
There are some that would ship from the U.S. without tools but the price is more like fifty bones instead of 30 something.
Good Luck
Click to expand...
Click to collapse
You are brave soul for recommending such a bad tools.
Sent from my SAMSUNG-SGH-I897 using Tapatalk
Thanks for the recommendations everyone
Do you suggest a better pack of tools? Why do you say they're bad?
Sent from my MB860 using XDA App
greenstuffs said:
You are brave soul for recommending such a bad tools.
Sent from my SAMSUNG-SGH-I897 using Tapatalk
Click to expand...
Click to collapse
Nah, they are more than capable. I replace digitizers frequently and I rarely have to break out my "good set' of tools. Yeah these are simply cheap lumps of plastic. But they work. And these tools should be safer to use than almost anything that the average person, who doesn't do this sort of thing regularly, might have on hand. I just didn't want him to order a digitizer and attack it with a butterknife. I was trying to be subtle about it tho... We don't want anyone to scuff their bezel now do we?
I am always on the lookout for great deals on tools for this. And I look forward to your recommendation for a tool set.
Atrix 4G Glass
You can find a replacement glass here. globalpartsdirect dot com
G2Smooth;129674
33 said:
You can find a replacement glass here. globalpartsdirect dot com
Click to expand...
Click to collapse
You mean http://www.globaldirectparts.com/SearchResults.asp?Search=atrix
Your phone should be under warranty! Call company first!
Sent from my MB860 using XDA Premium App
gonka95 said:
Your phone should be under warranty! Call company first!
Sent from my MB860 using XDA Premium App
Click to expand...
Click to collapse
Warranty covers a broken screen? Reason I ask is because I would rather have MOTO replace the screen (or the phone entirely) than me replacing the screen and voiding the warranty. I do not have insurance
I broke the glass on my phone 3 weeks after I bought it and didnt have insurance on it. I called motorola and they sent me an rma. I sent it in and they sent it back to me fixed in less than a week. If I remember right it cost $90 for them to fix it.
so it was only the digitizer after all?
+1 for photo of toilet roll by the bed, classy...
Sent from my MB860 using Tapatalk 2
JdgM3NT4L said:
Nah, they are more than capable. I replace digitizers frequently and I rarely have to break out my "good set' of tools. Yeah these are simply cheap lumps of plastic. But they work. And these tools should be safer to use than almost anything that the average person, who doesn't do this sort of thing regularly, might have on hand. I just didn't want him to order a digitizer and attack it with a butterknife. I was trying to be subtle about it tho... We don't want anyone to scuff their bezel now do we?
I am always on the lookout for great deals on tools for this. And I look forward to your recommendation for a tool set.
Click to expand...
Click to collapse
A friend and I splurged on the $60 iFixit tool kit because we made some spare cash on the side repairing classmates' phones. It works well, although I still don't know if I would justify the price. It seems that the major complaint on reviews for replacement electronics parts are the parts that come with them, if at all, so maybe getting a better set is worth it if you replace digitizers frequently. Replacing the Atrix digitizer/screen is a fairly easy task compared to other phones until you get to putting the new screen on, at which point trying to get the cables back into the housing becomes a pain.'
Good luck!
consolation said:
+1 for photo of toilet roll by the bed, classy...
Sent from my MB860 using Tapatalk 2
Click to expand...
Click to collapse
Lol.....betting if you look hard enough there's lotion there somewhere too!
Sent from my MB860 using xda premium
Ugh I'm going to have to do this. My digi. Is farked as well. Now, is there a video to put this back together?. I agree that taking it apart is not the hard part at all.
iFixit will have a tear down guide.
Sent from my MB860 using Tapatalk 2
Surprisingly there is no video to put it together...
Let me tell you from experience that it's damn near impossible to put it back together without tearing the digitizer ribbon straight off the screen while trying to slip it through that tiny hole that you pulled it out of. I've replaced two screens and I still don't think I can get it right.
My screen cracked twice while still under warranty, so I played the clueless n00b after I replaced the glass (cracked screens are not covered under warranty) and claimed the phone wasn't working and I couldn't figure out why.
Strange thing is, I also couldn't find a place online that would do replacement digitizers either. I didn't look for long, but if you don't have an option of a warranty return, I'd pay the $50 or so to let someone else do this for you and get it right...
YMMV...
I recommend taking it apart completely, you can attach the digitizer to the bezel/chassis and then you don't have to deal with trying to slide the cable through that tiny hole, you can just clean the digitizer, clean the lcd, put them together and then put the entire mounting plate back together and it just clips straight in...essentially you make this:
http://www.ebay.com/itm/180835204777?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
completely removes the chance of tearing the cable off the back of the digitizer...which is pretty common, sort of adds the step of getting the mounting plate off the fascia bezel...but its not to hard, be careful when popping up the volume/buttons camera cable area, that cable tears easily.
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
Anyone have a surefire repair for a scratched screen?
Has anyone had success with the watch repair guys that fix the watch faces in the mall?
I'm depressed that my 2 day old Note has a scratch and I'd like to be happy again.
Sent from my SAMSUNG-SGH-I717 using XDA
wow ...never heard of anyone getting a scratch repaired or buffed out...I don't believe you can....its not a tv where the glass could possibly get smooth out or buffed.....under that light film is many electroids that make current for the touch....the ditigizer.....do u have insurance on it?.....and have that film that came on the phone stock?.....say it don't charge or ssomething...put the film back on and send it out.. lol....that's what I try...what's the worst it happen....say it got damaged in shipping....lol....it will get placed on a self till a tech gets a work order to fix it by then..it will be forgotton and you'll have a replacement....these screens have issues anyways I look at it that way......lol blacks are grey....
Im wondering if one of the scratch removing liquids would work.? I think they sell it at hardware stores, its sold as a car windshield scratch remover...
depending how deep and big the scratch is filling it with liquid glass fixer...would he loose touch in that area?...how big is the scratch anyways and how deep you think?
edit...there is a liquid filler and scratch fixer for acrylics we used to at work...it goes on liquid and dries clear...for minor cracks but that depends how bad it is,then we would buff the scratch out..but I don't know if that work on these screens..might cause more harm then good..
I've got the Best Buy Black Tie coverage but as silly as it seems, they will only take it back if the screen is completely cracked. Plus, I just got done modding the heck out of this thing so I'd like to keep it. The scratch is deep enough to feel with your finger nail and can be easily seen in the right angles. It's annoying enough that I stare at it. Ive already tried polishing compound for car paint and seen no improvement. Someone told me there are kiosks at the mall where watch repair people fix watch faces. It sounds like a good idea but after reading a post by a guy who redid his Captivate screen, I'm not so hopeful.
Sent from my SAMSUNG-SGH-I717 using XDA
I read a post on here somewhere where a guy sanded and polished his own screen to remove a lot of scratches. It was a very detailed post. Actually I think the thread was a link to a post in the Vibrant forum or something. I don't remember which subforum it was in though. I'll try to look and find it again.
lactardjosh said:
I read a post on here somewhere where a guy sanded and polished his own screen to remove a lot of scratches. It was a very detailed post. Actually I think the thread was a link to a post in the Vibrant forum or something. I don't remember which subforum it was in though. I'll try to look and find it again.
Click to expand...
Click to collapse
Thanks. I saw that post and thats what I was eluding to. VERY detailed and way too indepth for me to handle.
Sent from my SAMSUNG-SGH-I717 using XDA
Try going back to AT&T store and see if they'll swap it for you since you're still in the first 30 days. I traded my black Note for a white one, just had to pay $35.
A cotton cloth and toothpaste or metal polish will get it out after many hours of rubbing.
Almost any screen protector over top should instantly improve the look and feel.
The Touch Digitizer Screen cover is hard to get now at a good price, but they will most likely drop to $50 before too long.
I've been using my Note since I got it in March of this year. I didn't purchase a case as I had my iPhone 3GS for close to 3 years and never had an issue dropping it or damaging it.
A few weeks ago I took a picture and it didn't look real good. I opened other pictures I had taken previously and they looked much sharper. I looked into settings and everything looked normal. I looked at the camera window and noticed it was scratched and dirty looking. I tried cleaning it but that didn't do anything.
I contacted Samsung and was told this is physical damage and I need to pay to get this fixed.
I'm not one to try and get everything fixed for free but in this case I think it's a poor design of the camera window as it isn't caved in and sticks out and can get scratched by having the phone rest on it's back. I think this is the normal way to place the phone when I'm not using it.
I would like to know if you guys think this is a poor design or if I'm the one who messed it up ? I know I could of bought a case and this would of never happened but I think if a phone needs a case to keep this from happening then Samsung should supply the case or worn you that you need one. My iPhone 3GS with no case never had an issue with the camera window getting scratched.
If you think this should be covered under warranty how should I convince Samsung as they tell me it's not.
Thanks for your time.
Just hard brick it and return it in for warranty. That's how most folks nowadays do it.
Sent from my SAMSUNG-SGH-I747 using xda premium
I can't speak for your phone, but I never use a case on any phone. My phones go through hell, very dusty and harsh environment (custom cabinet maker / installer). I have never had a problem with my camera lense cover. And I'm the guy who walks in the office and does the toss slide on the desk with my phone. But one thing I'm very good about is nothing ever goes in the pocket with my phone. Change, keys, lighter, none of that. But as hard as they try to make sure everything they produce is of the same quality, there are exceptions that slip through the cracks.
I love my note!
21productionz said:
I can't speak for your phone, but I never use a case on any phone. My phones go through hell, very dusty and harsh environment (custom cabinet maker / installer). I have never had a problem with my camera lense cover. And I'm the guy who walks in the office and does the toss slide on the desk with my phone. But one thing I'm very good about is nothing ever goes in the pocket with my phone. Change, keys, lighter, none of that. But as hard as they try to make sure everything they produce is of the same quality, there are exceptions that slip through the cracks.
I love my note!
Click to expand...
Click to collapse
I always put in my pockets with nothing in my pockets. I will admit I do put it on the counter when I'm at a bar and may move it around on the counter but I still think a 600 dollar phone shouldn't have the camera window flush where it can get scratched.
I sent Samsung an email telling them I find this unacceptable and that this should of never happened and it's not because I'm careless. If they expect us to use a case then supply it with the phone or maybe tell us to never put the phone on it's back as the camera window may get scratched. Guess if they still expect me to pay to get the window changed I will have to learn how to hard brick the phone.
I love my Note and changed because I liked the bigger screen and having a better camera than my iPhone 3GS. I've dealt with Samsung for an issue with my TV and it was pretty hard to get things resolved. Now I have an issue with one of there phones and it seems to be an issue again. My 3GS had an issue with the sensor called Apple got an appointment at an Apple store got there 15 minutes later I was out with a new phone. The new phone had the power supply burn up. Same scenario call got to the Apple store 15 minutes later out with a new phone. That being said I prefer Android over iOS but for customer service Samsung is way behind Apple.
Thanks for the replies. Will keep yo posted on the reply from Samsung to my latest email.
That's your bad my camera is fine and I've had it since pre-order. No case either.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
I hate to say this but "IF it had a case, this probabaly would've never happend". The HTC one X camera bulges out and so far there isn't a lot of complaints about the camera lense getting scraped. Claiming that it was poorly designed is just a bad excuse.
-Once you go NOTE, you'd say 4 inches a Joke
[Lady]: "How do you carry that huge phone in your pocket?"
[Note User]: "I'm used to having huge stuff in my pants"
I never touch my lens with anything but a micro-cloth (plus it's in a fairly thick case, so sliding it around isn't an issue), and even then I got a scratch on it straight through the middle the first week I had the phone. But it's not noticeable in pictures. You'd REALLY have to screw up the lens to be able to see anything in a picture, the focal point is so far away from the lens...
EDIT: You may be able to just find a replacement lens and fix it yourself. I did that on a prior phone when the lens cracked from being dropped.
The camera is just that lens with a ribbon cable that connects it to the mainboard. Its not too hard to remove. I have seen replacements for other phones available.
Thanks for the replies. All I know my pictures look grainy now and when I look at the lens/window it's dull looking and I can't get it back clear. If I messed this up I would like to know how I did this as I have done nothing different with my Note compared to my 3GS. Will look into trying to fix this myself as paying 75-100 to get this done by the Samsung service center is expensive. I could understand if I did something stupid to mess it up but as far as I know I didn't.
DS1969 said:
I've been using my Note since I got it in March of this year. I didn't purchase a case as I had my iPhone 3GS for close to 3 years and never had an issue dropping it or damaging it.
A few weeks ago I took a picture and it didn't look real good. I opened other pictures I had taken previously and they looked much sharper. I looked into settings and everything looked normal. I looked at the camera window and noticed it was scratched and dirty looking. I tried cleaning it but that didn't do anything.
I contacted Samsung and was told this is physical damage and I need to pay to get this fixed.
I'm not one to try and get everything fixed for free but in this case I think it's a poor design of the camera window as it isn't caved in and sticks out and can get scratched by having the phone rest on it's back. I think this is the normal way to place the phone when I'm not using it.
I would like to know if you guys think this is a poor design or if I'm the one who messed it up ? I know I could of bought a case and this would of never happened but I think if a phone needs a case to keep this from happening then Samsung should supply the case or worn you that you need one. My iPhone 3GS with no case never had an issue with the camera window getting scratched.
Thanks for your time.
Click to expand...
Click to collapse
Hi, perhaps you should look into getting a replacement lens from ebay.
Here's a link:
http://www.ebay.com/itm/OEM-SAMSUNG...795739?pt=PDA_Accessories&hash=item20c9df1c9b
If you think this should be covered under warranty how should I convince Samsung as they tell me it's not.
DS1969 said:
Thanks for the replies. All I know my pictures look grainy now and when I look at the lens/window it's dull looking and I can't get it back clear. If I messed this up I would like to know how I did this as I have done nothing different with my Note compared to my 3GS. Will look into trying to fix this myself as paying 75-100 to get this done by the Samsung service center is expensive. I could understand if I did something stupid to mess it up but as far as I know I didn't.
Click to expand...
Click to collapse
You obviously did if it's not an issue for anyone else...
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
Otterbox. Period.
Sent from my SAMSUNG-SGH-I717 using xda premium
Yes ....otterbox ....
Mine has been very effective ....g
I don't really like cases but I went with the otterbox commuter and I love it. You might want to look into a case once you fix the camera.
My outside silver bezel was scratched from dropping and it also has the camera window. Not to hard to replace. Just need to undo screws and something to pry it off. Found part on eBay.
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2
If you've been relegated to spending money to fix it or getting a warranty replacement, maybe try to polish it first, it has worked for me in the past with similar issues. I don't know if its a polycarbonate lense, but automotive stuff always helped me. Meguiars plastiX is the stuff I've used with reasonable success, at least with plastic parts. Maybe trying something like that will help clear it up, if the scratching isn't too deep anyway.
I am going to try this tonight.. as i also have a very very beat up camera window and mines been in a case from day 1. but its in my pocket with countless other things. i am going to try and hand polish it and if that fails low speed dremel with a polish wheel and some polish creme lololol worst that happens is i screw it up.. i've got a spare note anyways. I'll try and post some before an after pictures.
EDIT:
after looking at the protective shell its just plastic and not even attached to the camera. you can buy the replacement lens cover here for $5 and its 9 screws to change it out
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=140854323974
That's what I did. Hardest part is popping off the piece. I used something called an orange stick (plastic wedge thing). Its very easy though, hope it works out for you.
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2
ukguy115 said:
That's what I did. Hardest part is popping off the piece. I used something called an orange stick (plastic wedge thing). Its very easy though, hope it works out for you.
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2
Click to expand...
Click to collapse
If u take the phone apart so the back is off 9 screws and a case opener tool. you can bend those tabs straight and the piece falls right out. drop the new one in and bend the tabs down and done.
If you take some paper and roll it up and put it on either side of the camera when you're snapping the back cover on it will make it pop up enough to stick out a bit further than the camera cover but not so far as to stop it from locking all the clips on the cover. When you put it back down after that the camera cover doesn't touch the table.