Related
I tryed flashing a rom without disabling voodoo and know my phone wont even turn on. Any help please!!!!
ireiricky said:
I tryed flashing a rom without disabling voodoo and know my phone wont even turn on. Any help please!!!!
Click to expand...
Click to collapse
If you look couple threads down, you'll see my thread, and I am having the same problem. Slightly different cause, but of the same nature, and the exact same problem. I have not had any real help yet, but I have been scouring the forums here. And I think the only option, if none of the button combinations work, as they don't seem to for me, and you're getting a complete brick, is perhaps the usb jig resistor method... but even that I don't think is 100% because some of the people who created the guides on how to make the jig resistor said it only worked for softbrick, not total brick like our cases. Unless someone can verify otherwise...
Thanks for the reply man i don't know what to do man i spent $400 0n this phone there must be a way but no luck on google either
ireiricky said:
I tryed flashing a rom without disabling voodoo and know my phone wont even turn on. Any help please!!!!
Click to expand...
Click to collapse
Try this. Take your sim card, microsd and battery out. Leave battery out for a few minutes.
Open odin and load with the 512 pit and Jfd tar.
Plug one end of usb cable into computer only
take your vibrant with everything still out of it
hold down both vol buttons (vol up and down) and never let go
do not touch power
while holding down both volume buttons plug in your usb cable into the phone with the other end previously in the computer...do all this while holding down volume buttons and dont let go
now grab your battery with your free hand and while still holding down the vol buttons now plug in your battery
if all goes well your.phone should go into download mode at which pt you can let go of volume buttons.
If this doesnt work you can maybe try the jig if your bootloader is intact
also since you were messing with voodoo you might need to first flash eugenes froyo tbat doesnt brick...im not too sure on this so ask around and look it up.
You need this first of all (Froyo that does not brick)
http://eb-productions.proboards.com/index.cgi?board=samsungsgs&action=display&thread=8
jordanjf86 said:
1. Download Eugenes 'Froyo that does not brick' file.
2. Extract the files.
3. Open Odin, plug in your phone, then put it into download mode.
4. load the PIT file in appropriate area.
5. load the .tar file in the PDA area.
6. DO NOT check 're-partition'.
7. Click start, let it finish. Your phone will load and reboot into stock recovery. It will error out again. DONT panic! This is what's supposed to happen.
8. Now, pull your battery.
9. Download the 'True stock 2.1 firmware for the vibrant'.
10. Extract the files.
11. Once again, open Odin, plug in your phone, put into download mode.
12. Load the PIT file into the appropriate area and the .tar in the PDA area.
13. THIS TIME you want to check the 're-partition' box.
14. Now click start, let it finish, and this time your phone will load up just fine! BAM!
Click to expand...
Click to collapse
Don't forget to thank :]
iv'e tryied that i read somewhere that it's a hard brick
Then try accessing download mode by first, removing the sd card, sim, and battery, second, plugging in the usb cable, third, holding down the two buttons on the side of the phone, and finally, while holding down those two buttons, inserting the battery.
I havee tried that mothod many times no luck just a blank screen
Then commit a fraud and send it back to T-Mobile saying it suddenly stopped working.
Or if you prefer a wild card you can use a JIG
http://forum.xda-developers.com/showthread.php?t=819551
Edit: Never mind it will not work for you. Sorry :/
Edit 2: The phone does not even turn the buttons on??
no nothing turns on at all no power but when i put it to charge it heats up but no battery screen
Yea, take it to T-Mobile and get it replaced. I got mine switched at T-Mobile once, and it would only boot to the custom Nexus animation....the lady still swapped it out. It all depends on the rep, if they won't switch it, go to a different location. Eventually you'll find someone.
i don't think thats possible seeing as im in Canada bought it off ebay
take it to a phone expert. he will flash a bootloader to your phone.
Sent from my SGH-T959 using XDA App
I had a rooted vibrant running pretty nicely with all my apps optimized. ive always tried to install lagfix (voodoo, OCLF, UFL,), but none of them would ever work, they would just brick my phone and i would be stuck at the vibrant screen recovery loop.
no problem, i would go to download mode and flash odin...
few months later thought id give it another shot with the updates and such with voodoo...
again same thing... **** didn't work..
back to eugenes that does not brick and i was going to do the whole process again of getting back to the stock ji6.
in the middle of eugnes, there was a com error, dont know why, nothing was moved. the flashed had stopped in the middle.
took out the battery. and nothing. phone does nothing. plug it in, black screen. 3 button combo. black screen. not even the vibrant logo. and no charging screen.
black screen no matter what.
do i need to do the 'jumpstart' jtag method?
Google search it! It says dl odin and stuff just unbricked mine
Sent from my SGH-T959 using XDA App
stealthj said:
I had a rooted vibrant running pretty nicely with all my apps optimized. ive always tried to install lagfix (voodoo, OCLF, UFL,), but none of them would ever work, they would just brick my phone and i would be stuck at the vibrant screen recovery loop.
no problem, i would go to download mode and flash odin...
few months later thought id give it another shot with the updates and such with voodoo...
again same thing... **** didn't work..
back to eugenes that does not brick and i was going to do the whole process again of getting back to the stock ji6.
in the middle of eugnes, there was a com error, dont know why, nothing was moved. the flashed had stopped in the middle.
took out the battery. and nothing. phone does nothing. plug it in, black screen. 3 button combo. black screen. not even the vibrant logo. and no charging screen.
black screen no matter what.
do i need to do the 'jumpstart' jtag method?
Click to expand...
Click to collapse
you should post in Q & A next time. Anywhoo, can you get your phone into download mode?
I can tell you that I've been there, I can say with all certainty that this phone has recovered from the brink of of death so many times I don't even scare anymore. I just flash. You got to be patient I dug around Google and the forma and found the right combo that put me in download mode.
It was power and vol. down. No sim no sd.
I've learned that every phone responds to a different combo. Your phone isn't dead, just Samsung hibernating.
Sent from my SGH-T959 using XDA App
You seem to know what you are doing when it comes to flashing. All I can suggest is to try the various methods to get into download mode again. Some people have methods that work best for them. For instance, the 3 button combo never works for me. But pulling the battery, putting back in, holding down only the up and down volume keys (NOT POWER) and while holding insert the usb that the other end should already have been plugged into the computer.
but i'd say its safe to assume if you cant get to download mode by any of the methods on this forum, there is no going back.
Sent from my SGH-T959 using XDA App
Do a search for the jig also as a last resort, try checking in the bible I can't remember where that thread is, but it has helped quite a few people..
try two buttons combo up and power or down and power with the usb plug in
This is the absolute surefire way to get your phone into DL mode:
1.) Take out battery, SIM, and Memory card
2.) Connect phone to the computer
3.) Put battery back into phone while holding down up and down vol buttons
If your phone can still get into DL mode this way will do it guaranteed. The jig might also help but as far as I know it really only helps if your phone is hardware locked. If the above steps dont work for you then I'm afraid that the bootloader is gone and you are screwed =/
I saw a jig offered as a for sale item on the Team Whiskey forum. I believe it was around 9 or 10 dollars (maybe less) If you decide to go that route. Good luck!!!!!!!!!
thanks for all the replies everyone.... from what it looks like and to the extent of my knowledge, it looks like the bootloader is gone. my guess is it was flashing the bootloader? while the computer randomely decided to drop the com port?
anyhow, i refuse to let it die and am going to keep trying!
well that was weird. it worked. sim, battery, everything out, i held all 3 buttons, plugged USB and battery and let go of power all at EXACT same time and wallah! download mode. flashed eugenes, flashed UFD, then JI6. rooted, installed busybox, downloaded rom manager. found the backup i made before trying to install lagfix.... vibrant is stuck at 'vibrant' screen now... so flashed again eugenes, UFD, then JI6 again....
working normal again but i want my data from the backup....
advanced restore should i do? NOT restore the boot? only restore the data/system or or other options in clockwork recovery advanded restore? any help would be appreciated. first time trying to actually restore data from a clockwork backup.
Moved of: Samsung Vibrant > Vibrant Android Development
To: Samsung Vibrant > Vibrant Q&A
Please put your questions to: Vibrant Q&A
I have had the phone to pc screen before but plugging in the USB and holding the volume buttons arent working this time. Is there any other trick or special way to get around this?
What shows on your screen? R u completely bricked? Do u get a logo?. If u get the computer logo. Plug it in. Let the logo show up. Hold the 3 buttons. As soon as the screen turns black let go of power... let me know how it goes
Sent from my SGH-T959 using XDA App
Hi, I am having a serious problem
My vibrant was working and i was flashing the firmware T959UVKA7 using odin 1.3
once the update was done and it odin said passed
the phone is not turning on at all, act like there is no battery
tried to plug it to wall charger not even responding, its like dead, no power at all
i even tried to remove the battery for 5 min, add it again and plugged the jig
nothing is happenning, tried every combination of keys, even connect it to computer usb with no battery then plugged the battery, nothing, the phone is completely dead
Please let me know if there is any way i can make it to work again? or i totally bricked it?
Sami
Did you try and get into download mode? Connect usb to computer. Hold both up down buttons then plug in usb
Sent from my SGH-T959 using XDA App
jrod33084 said:
Did you try and get into download mode? Connect usb to computer. Hold both up down buttons then plug in usb
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
Thanks for the reply, well i tried all.. the problem is my phone isnt even turn on... its acts like there is no battery, even if i plug it to the wall charger it doesnt turn on or give me the battery status icon that is charging
its completely black screen, even the button light dont turn on, nothing turns on and the battery is fully charged
any idea? anyone know how i can fix it?? does that means i ruined my phone forever or is it fixable???
http://forum.xda-developers.com/showthread.php?t=848737 this will make it more clear
bartek25 said:
http://forum.xda-developers.com/showthread.php?t=848737 this will make it more clear
Click to expand...
Click to collapse
Yes read that
Sent from my SGH-T959 using XDA App
samiriad said:
Hi, I am having a serious problem
My vibrant was working and i was flashing the firmware T959UVKA7 using odin 1.3
once the update was done and it odin said passed
the phone is not turning on at all, act like there is no battery
tried to plug it to wall charger not even responding, its like dead, no power at all
i even tried to remove the battery for 5 min, add it again and plugged the jig
nothing is happenning, tried every combination of keys, even connect it to computer usb with no battery then plugged the battery, nothing, the phone is completely dead
Please let me know if there is any way i can make it to work again? or i totally bricked it?
Sami
Click to expand...
Click to collapse
Which firmware (kernel only or complete)? Link?
Which OS were you from before odin up the KA7?
I ran into similar problem. I was from Stock Froyo Kies, then odin over the supercurio stock+kernel KA7. It got black screen ...for a good 5-10 min. I was going to pull out battery but I heard some mumble jumble in the background telling me that it's converting (voodoo ext4) so I left it alone. If you pulled out too early during the conversion before it finish doing voodoo...I'm not sure what happened to that unless your odin KA7 does not have odin. Do you see any light, sound, or splash screen at all?
When you flash, did you have "repartition" checked or not?
Anyway, have you try the 2 button download mode? Mine was silent dead black screen too at one point from last few days with few variation difference caused by different tinkering mistakes. I just took off battery, sim, sd and kill odin. Reput them all back and fire up odin. Hold down both the + and - with 2 fingers, then hook in USB from pc to phone. It should put it to download mode and you can reodin whatever...depends what it can do.
same situation here.
i came from T959UVJFD then i flashed T959UVKA7 (.tar.md5 file from samfirmware.com) using odin3 v1.70
odin says it was finished. but it doesnt turn on anymore. i cannot even go to download mode.
PLEASE HELP!
any kind of button combo doest work
try downloading odin3v 1.85 and using this method to put in to download mode
1. pull the battery,
2. put it back in;
3. then, with the phone still off, plug your usb into the computer,
4. turn on odin3,
5. hold the center of the volume buttons,
6. plug the usb to the phone while holding the volume botton
orginally found in this my posting
http://forum.xda-developers.com/showthread.php?t=1471231
I know I'm posting this on multiple threads, but Im desperate! I'm having the exact issue as OP, am hoping a suggestion from someone helps. Right now my hope is hanging on the comments from people here claiming "it is REALLY difficult to brick this phone".
I was "downgrading" from ICS Passion with GB bootloader, down to stock. The "downgrade" to 2.1 worked fine. Then I used Kies to upgrade to Froyo, and after the install it shutdown, and now the phone doesn't respond to any key. Tried a different battery as well, to eliminate a probably battery issue. No good.
Tried different combos to get to recover/download modes: Vol UP + Power, Vol Down + Power, Vol Up+Vol Down+Power, and Insert Cable+ Vol UP+Vol Down - nothing yet. Used ODIN 1.85 with suggestion from canyon789, and that didn't work either.
Any ideas? Please help.
meascom said:
I know I'm posting this on multiple threads, but Im desperate! I'm having the exact issue as OP, am hoping a suggestion from someone helps. Right now my hope is hanging on the comments from people here claiming "it is REALLY difficult to brick this phone".
I was "downgrading" from ICS Passion with GB bootloader, down to stock. The "downgrade" to 2.1 worked fine. Then I used Kies to upgrade to Froyo, and after the install it shutdown, and now the phone doesn't respond to any key. Tried a different battery as well, to eliminate a probably battery issue. No good.
Tried different combos to get to recover/download modes: Vol UP + Power, Vol Down + Power, Vol Up+Vol Down+Power, and Insert Cable+ Vol UP+Vol Down - nothing yet. Used ODIN 1.85 with suggestion from canyon789, and that didn't work either.
Any ideas? Please help.
Click to expand...
Click to collapse
If your willing to wait the approx. week, call up Samsung tell them that you were updating through Kies and then your phone would no longer turn on, you've tried different batteries and tried different cables and still nothing, she/he will try to help you get into recovery mode, just go along with it, she will then help you get everything you need to send it to Samsung's nearest repair center. Sent mine in last thursday, they replaced the PBA (logic board) and are sending it now. Should be here in 2 days :]
meascom said:
I know I'm posting this on multiple threads, but Im desperate! I'm having the exact issue as OP, am hoping a suggestion from someone helps. Right now my hope is hanging on the comments from people here claiming "it is REALLY difficult to brick this phone".
I was "downgrading" from ICS Passion with GB bootloader, down to stock. The "downgrade" to 2.1 worked fine. Then I used Kies to upgrade to Froyo, and after the install it shutdown, and now the phone doesn't respond to any key. Tried a different battery as well, to eliminate a probably battery issue. No good.
Tried different combos to get to recover/download modes: Vol UP + Power, Vol Down + Power, Vol Up+Vol Down+Power, and Insert Cable+ Vol UP+Vol Down - nothing yet. Used ODIN 1.85 with suggestion from canyon789, and that didn't work either.
Any ideas? Please help.
Click to expand...
Click to collapse
Did you try the exact no-boot steps from the Guide linked to above?
I tried everything else, only the exact sequence worked.
Battery out, phone plugged in, Odin running: press center of volume keys,
insert battery.
cashmundy said:
Did you try the exact no-boot steps from the Guide linked to above?
I tried everything else, only the exact sequence worked.
Battery out, phone plugged in, Odin running: press center of volume keys,
insert battery.
Click to expand...
Click to collapse
Yes tried the exact same steps, no luck. Ordered a jig finally and hoping that will get me out of this mess
I hope the jig works for you. So much for "unbrickable". I will be sure never to Odin anything but the JFD file. Good luck.
work perfect for me thanks
meascom said:
Yes tried the exact same steps, no luck. Ordered a jig finally and hoping that will get me out of this mess
Click to expand...
Click to collapse
his is not going to help at all, you damage the bootloader you as happened to me, but in my case it did ODIN, Mini Kies did.
The only thing you can try and see if you have some success is to do two things:
* Easy way: pay for you to get a JTAG on the phone and reinstall the bootloader. (Actually that's what you Damage to flash it)
* Terse: Vibrant Unbrickable do MOD
(but must be done by someone who is skilled in welding and electronics, as this takes a lot of risk, as is jumping two pins that control the processor of the phone)
note that the device is already damaged, you try to repair it, if you do not succeed, At Vibrant Ebay sell broken, win one for 53.66 at auction. and attempting to repair Give you a MOD.
I hope you will help.
If Mini Kies damaged your phone, call Samsung, tell them that you upgraded with Mini Kies and now it won't turn on and they replace it for free.
xXcybersniperXx said:
If Mini Kies damaged your phone, call Samsung, tell them that you upgraded with Mini Kies and now it won't turn on and they replace it for free.
Click to expand...
Click to collapse
This can be another solution, if you carry LUCK and Warranty!!!!!
I was flashing from MIUI 1.9 to MIUI ICS in CWM and all seemed well until upon boot it hung on the MIUI bootup screen. After waiting about 15 minutes I figured I would simply ODIN back to stock and try again as I normally do when I have a problem flashing. In ODIN however I was unable to make it past the boot.inf stage of the flashing. Stupidly I unplugged the usb cable mid flash and tried again, and again same result, it would hang at boot.inf. After trying a couple different stock ODIN files the phone will not turn on at all. Even if I pull the battery and connect the phone to the pc I cannot boot into download mode. When I connect to the wall charger the battery screen does not come on either.
Strangely if I press the power button on the phone with the phone connected to the pc, windows will make the sound of a usb device being connected, however, if I release the power button it makes the sound of a usb device being disconnected. ODIN does not seem to be recognizing my phone anymore since I haven't been able to boot into download mode.
I've bought a usb jib hoping this would solve the problem but it hasn't seemed to work. Maybe I'm doing something wrong.
Please someone help me get my phone up and running again. I've flashed numerous roms before and had trouble but nothing as serious as this.
Try reading up on Droidstyles Guide . Its in General section .
Sent from my SCH-I500 using xda app-developers app
Thanks for that. I went through his guide but unfortunately I think my problem is a little more serious. My phone will not turn on at all. I cannot boot into CWM, download mode or boot normally. The screen just remains black. It doesn't show up as a recognized device in windows but when I connect the usb cable it makes a sound of it being connected.
If any has any ideas on things I could try I would be really grateful. I bought my phone out of contract and can't really afford to buy a new one right now.
iztel said:
Thanks for that. I went through his guide but unfortunately I think my problem is a little more serious. My phone will not turn on at all. I cannot boot into CWM, download mode or boot normally. The screen just remains black. It doesn't show up as a recognized device in windows but when I connect the usb cable it makes a sound of it being connected.
If any has any ideas on things I could try I would be really grateful. I bought my phone out of contract and can't really afford to buy a new one right now.
Click to expand...
Click to collapse
Can you "3 finger" into recovery ?
Sent from my SCH-I500 using xda app-developers app
No, when I try to use the 3 buttons to boot into recovery the screen stays black.
Another strange thing it's doing is when I connect the phone to my Mac with the SD card in the phone the Mac will continuously popup a window that asks whether I want to connect the usb device to the Mac or my virtual machine. It flashes so fast I'm unable to click either option. If I connect the phone without the SD card in this menu never comes up but I'm still unable to boot into download mode.
Hmm....I've never heard this before...have you tried plugging phone charger in ( wall outlet ) and let it charge 8 full hours
Sent from my SCH-I500 using xda app-developers app
You say you bought " out of contract", from a private seller ? No warranty?
Sent from my SCH-I500 using xda app-developers app
I charged it from the wall charger overnight still no luck. Yeah, I bought it a year and a half ago used from ebay. I think it's really strange too. I've had plenty of hiccups flashing roms before but it's never been something ODIN couldn't fix and I'd at least be able to get into download mode.
I think you are going to have to use UnbrickableMod.
Thanks MM. I bit the bullet and bought a used Galaxy S II. I may still try that unbrickable mod so I can give my Fassy to my mom who's overdue for a smartphone. I've never used a soldering iron though and not too certain how successful I'll be.
iztel said:
Thanks MM. I bit the bullet and bought a used Galaxy S II. I may still try that unbrickable mod so I can give my Fassy to my mom who's overdue for a smartphone. I've never used a soldering iron though and not too certain how successful I'll be.
Click to expand...
Click to collapse
Have you tried the wall plug trick?
I had been running a Fascinate rom on a Showcase for almost a year & the same thing happened to me. Initially, the battery had run completely down and after full charge, I had nothing but bootloops. At first I could connect via odin, but could not complete flash.
After messing with it & yanking out the cable as you did, I had same issue, blank screen, pc would beep but that was it, pc/odin would not recognize or show the comm port. I would get unknown device.
Ultimately, I successfully repartitioned & odined a stock Fascinate Froyo EB01 rom by doing several things -- not sure which worked, but perhaps might work for you rather than soldering
First, I fully charged an oem battery using a spare battery charger (not in the fassy)
After charge, I put the batt in the fasc & plugged the fasc in to the wall charger while holding down the volume button & got the download mode to show up.
I left batt in when I unplugged from wall & the download mode stuck.
Odin still didnt recognize on my laptop, so I tried 3 other machines till I Odin finally saw the fascinate, at which point I odined Froyo with .pit & repartitioning as my starting point, then clockworked & rooted etc. I think I left battery in during the flash, then reflashed later in download mode with battery out.
I was also successful using heimdall a few times, when another pc wasn't available & odin wasn't playing nice. Was very odd, as 2 of those laptops ALWAYS worked fine with odin & the fascinated showcase before. Now they still won't recognize, but I can easily odin if I try diff computers --- some windows 7 some xp & some vista.
Magickly said:
Have you tried the wall plug trick?
I had been running a Fascinate rom on a Showcase for almost a year & the same thing happened to me. Initially, the battery had run completely down and after full charge, I had nothing but bootloops. At first I could connect via odin, but could not complete flash.
After messing with it & yanking out the cable as you did, I had same issue, blank screen, pc would beep but that was it, pc/odin would not recognize or show the comm port. I would get unknown device.
Ultimately, I successfully repartitioned & odined a stock Fascinate Froyo EB01 rom by doing several things -- not sure which worked, but perhaps might work for you rather than soldering
First, I fully charged an oem battery using a spare battery charger (not in the fassy)
After charge, I put the batt in the fasc & plugged the fasc in to the wall charger while holding down the volume button & got the download mode to show up.
I left batt in when I unplugged from wall & the download mode stuck.
Odin still didnt recognize on my laptop, so I tried 3 other machines till I Odin finally saw the fascinate, at which point I odined Froyo with .pit & repartitioning as my starting point, then clockworked & rooted etc. I think I left battery in during the flash, then reflashed later in download mode with battery out.
I was also successful using heimdall a few times, when another pc wasn't available & odin wasn't playing nice. Was very odd, as 2 of those laptops ALWAYS worked fine with odin & the fascinated showcase before. Now they still won't recognize, but I can easily odin if I try diff computers --- some windows 7 some xp & some vista.
Click to expand...
Click to collapse
I had the same issue. I think it had to do with the battery being too low. I think that ODIN could have a check in place to allow only to flash if the battery is not clos to low in case things go wrong. I had a second fully charged battery and when i read the above post, i changed the battery across and it set it to download and ODIN eventually detected it. Thanks for the help guys.
I have a similar problem, I was on PA JB rom 2.18, and I decided to flash latest devil kernel [1.5.2? or something like that]
so then it would just boot into devil recovery. and that's all. Tried to flash pa rom over it [to get stock recovery back] but it failed. also it had lots of errors about mounting.
So I did advanced restore, and chose to restore boot from other JB backup. This just made it worse, bootlooping into an android recovery with a "!" triangle, then immediately rebooting, over and over again..
So I put into download mode, and heimdall a boot.img extracted from the JB rom [paranoid android], and it still didn't work right.
So then I heimdall'ed the atlas.2.2.pit, thinking the partition was screwed. Then I was booted into cwm 6.x! So I thought I was out of the woods, and wiped, then flashed PA 2.18 jb rom, and then rebooted.. and then I had no samsung logo bootloop. I could tell cuz it was dark, and I could see the backlight coming on and off. on, off... on... off... endlessly.
I tried download mode, and it didn't work. That's when I got scared.. I tried it again, nothing. just the black [very dim black, because of super amoled technology] screen, coming on and off..
So I finally tried taking the battery out, and then it went into download mode!
But I still cannot figure out why it will not let me flash any rom. I'm gonna have to boot into windows and odin back to EH03.
Good thing I have a 3-4 day old backup.
So, do not use devil kernel unless you want a softbrick.
mvmacd said:
I have a similar problem, I was on PA JB rom 2.18, and I decided to flash latest devil kernel [1.5.2? or something like that]
so then it would just boot into devil recovery. and that's all. Tried to flash pa rom over it [to get stock recovery back] but it failed. also it had lots of errors about mounting.
So I did advanced restore, and chose to restore boot from other JB backup. This just made it worse, bootlooping into an android recovery with a "!" triangle, then immediately rebooting, over and over again..
So I put into download mode, and heimdall a boot.img extracted from the JB rom [paranoid android], and it still didn't work right.
So then I heimdall'ed the atlas.2.2.pit, thinking the partition was screwed. Then I was booted into cwm 6.x! So I thought I was out of the woods, and wiped, then flashed PA 2.18 jb rom, and then rebooted.. and then I had no samsung logo bootloop. I could tell cuz it was dark, and I could see the backlight coming on and off. on, off... on... off... endlessly.
I tried download mode, and it didn't work. That's when I got scared.. I tried it again, nothing. just the black [very dim black, because of super amoled technology] screen, coming on and off..
So I finally tried taking the battery out, and then it went into download mode!
But I still cannot figure out why it will not let me flash any rom. I'm gonna have to boot into windows and odin back to EH03.
Good thing I have a 3-4 day old backup.
So, do not use devil kernel unless you want a softbrick.
Click to expand...
Click to collapse
I think the problem is you used the wrong Devil... the latest is 1.6.1 and the older ones will not work with the new partition layout. Get it from http://rootaxbox.no-ip.org/derteufel/
Here is some FYI for you guys. If you are using a pc with a USB 2.0 or higher then it provides the power to go into download mode for Odin. That's why people say to remove the battery and then plug in the USB cable and hold the volume and power to go into download mode for odin. IF you are using a desktop then it's best to use one of the hardwired usb ports on the back of your pc, if it's a laptop then they are all hardwired to the motherboard. USB 2.0 and up all provide power through the usb port, therefore if you leave the battery in while Odin'ing it may not be a good outcome, this is just a suggestion.
netlagger said:
Here is some FYI for you guys. If you are using a pc with a USB 2.0 or higher then it provides the power to go into download mode for Odin. That's why people say to remove the battery and then plug in the USB cable and hold the volume and power to go into download mode for odin. IF you are using a desktop then it's best to use one of the hardwired usb ports on the back of your pc, if it's a laptop then they are all hardwired to the motherboard. USB 2.0 and up all provide power through the usb port, therefore if you leave the battery in while Odin'ing it may not be a good outcome, this is just a suggestion.
Click to expand...
Click to collapse
You are suggesting we leave the battery out while Odining? what good would that do?
mvmacd said:
You are suggesting we leave the battery out while Odining? what good would that do?
Click to expand...
Click to collapse
I always Odin without battery. Try it. Remove battery, connect to PC with Odin opened, hold volume down button for dl mode, and fash.
Sent from my SCH-I500 using xda premium
mezster said:
I always Odin without battery. Try it. Remove battery, connect to PC with Odin opened, hold volume down button for dl mode, and fash.
Sent from my SCH-I500 using xda premium
Click to expand...
Click to collapse
Yet again, I ask, what good would taking the battery out?
I'd have to set it and the cover down and put them back after Odin..
Sent from my Nexus 7 using xda app-developers app
mvmacd said:
Yet again, I ask, what good would taking the battery out?
I'd have to set it and the cover down and put them back after Odin..
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
It's probably just a precaution so you don't accidentally reboot the phone while flashing or something like that. Every guide I have read says to pull battery before using Odin so I do... and I haven't had any problems. I think it'll probably work fine with the battery in, but why bother taking the risk?
Crawshayi said:
It's probably just a precaution so you don't accidentally reboot the phone while flashing or something like that. Every guide I have read says to pull battery before using Odin so I do... and I haven't had any problems. I think it'll probably work fine with the battery in, but why bother taking the risk?
Click to expand...
Click to collapse
how would the battery cause the phone to reboot?
I have never Odin'd without the battery. And I never had any problems
I had tried to update my phone via Kies and the computer blue screened. Now the phone is stuck on the ODIN Mode screen with a picture of my phone on the left, a yellow triangle in the middle, and a computer on the right. Taking the battery out does nothing, restarting does nothing, restarting while holding down the volume buttons does nothing. No matter what, it always comes back to this screen.
When I plug the device into my windows based PC and open ODIN, ODIN does not see my phone. When I plug it into my linux computer and run lsusb, it does not list my phone in the output, so the computer definitely isn't recognizing that my phone is plugged in. A couple of weeks ago, I had this problem while trying to back up the phone, so I'm not sure if it's related to the botched upgrade or not.
Does anyone have any tips or advice here? I'd really love to be able to use my phone again. I am using the cable that came with the phone. I have the same results with other cables, as well....
I'm happy to provide more information if needed. Just tell me what you need to know.
That screen is a form of download mode. You should be able to flash stock or stock plus root from there.
When I plug the device into my windows based PC and open ODIN, ODIN does not see my phone.
Click to expand...
Click to collapse
If this statement reflects what you actually did, then it suggests the wrong order. You must first open oden on the desktop, and then connect the phone to the computer in download mode.
Try that first.
Next you could try putting the phone into download mode with the battery pulled out. Open Odin on the desktop, then with the battery out, hold down the vol- button while plugging in the usb cable.
Thanks for your response.
So I went ahead and cleared out everything and then reinstalled the USB drivers. Opened ODIN, connected USB to computer, took battery out of phone, put battery back in, held down volume buttons and inserted the cord. The screen immediately loaded up the one I spoke of in my first post. Odin still did not recognize that I had my phone plugged in.
So then I installed Kies and went to the firmware restoration item under the tools menu. Entered my model and serial number and put my phone into recovery mode according to the instructions there, but the "Start Upgrade" button was grayed out and never became clickable.
One thing I did notice while doing this (On yet another new computer) is that when I plug in the phone, I get a "USB Device Not Recognized" error in Windows. I'm not sure if this is a result of it being in download mode or not, but I thought it worth mentioning. I did attempt to blow out my mini USB on the phone for good measure, but had the same result, even with another cord.
On ur Windows pc, did u try different usb ports ? And don't use a usb hub.
Sent from my SAMSUNG-SGH-I747 using xda premium
Yes, multiple ports on multiple PCs.
The port was working fine yesterday when the Kies update failed.
Have u tried using a Jig to get ur phone into download mode ??
(See my signature link below. There r links there on how to make a jig and/or where to buy one)
Sent from my SGH-I777 using xda premium
First of all make sure that your PC isnt running Kies in the background - Use Tsk Manager to kill Kies process
Then Plug In your Phone
Enter Download Mode by holding both volume buttons and powerbutton till the Boot Screen Appears.Let the power button go when you see the boot screen but keep holding the volume buttons.
In no time you'll be in Download mode
Then go to odin and check if your computer recognises it. Odin willl show you (Com:x) X - Any Number
Then you can easily flash stock rom or a custom recovery..
Rushaan™ said:
First of all make sure that your PC isnt running Kies in the background - Use Tsk Manager to kill Kies process
Then Plug In your Phone
Enter Download Mode by holding both volume buttons and powerbutton till the Boot Screen Appears.Let the power button go when you see the boot screen but keep holding the volume buttons.
In no time you'll be in Download mode
Then go to odin and check if your computer recognises it. Odin willl show you (Com:x) X - Any Number
Then you can easily flash stock rom or a custom recovery..
Click to expand...
Click to collapse
I have already made sure Kies is not running (And have tried this on a computer without Kies installed) and according to creepyncrawly in the second post here, the screen that I'm seeing IS download mode.
4-2ndtwin said:
Have u tried using a Jig to get ur phone into download mode ??
(See my signature link below. There r links there on how to make a jig and/or where to buy one)
Sent from my SGH-I777 using xda premium
Click to expand...
Click to collapse
Again, according to creepyncrawly, this screen is a form of download mode. I am IN download mode already.
Special_Kev said:
I had tried to update my phone via Kies and the computer blue screened. Now the phone is stuck on the ODIN Mode screen with a picture of my phone on the left, a yellow triangle in the middle, and a computer on the right. Taking the battery out does nothing, restarting does nothing, restarting while holding down the volume buttons does nothing. No matter what, it always comes back to this screen.
When I plug the device into my windows based PC and open ODIN, ODIN does not see my phone. When I plug it into my linux computer and run lsusb, it does not list my phone in the output, so the computer definitely isn't recognizing that my phone is plugged in. A couple of weeks ago, I had this problem while trying to back up the phone, so I'm not sure if it's related to the botched upgrade or not.
Does anyone have any tips or advice here? I'd really love to be able to use my phone again. I am using the cable that came with the phone. I have the same results with other cables, as well....
I'm happy to provide more information if needed. Just tell me what you need to know.
Click to expand...
Click to collapse
I tried everything you did, and the only way I got Odin to recognize my phone was use a USB jig to get it into the download mode other people are talking about
Sent from my SGH-I777 using xda app-developers app
I'm definitely open to making one, but I'm confused since everything I'm reading says that the screen I described IS download mode, just with a different screen. Are you saying that you had the exact same situation as me and a Jig fixed it?
Special_Kev said:
I'm definitely open to making one, but I'm confused since everything I'm reading says that the screen I described IS download mode, just with a different screen. Are you saying that you had the exact same situation as me and a Jig fixed it?
Click to expand...
Click to collapse
You could order one fairly inexpensive. But order it or make it still takes some time. But as several have mentioned, it may help.
Did you try forcing download mode with the battery out as I suggested in the second post?
Yes, I have tried forcing download mode by taking the battery out, holding down Vol and inserting it again. These are also the instructions that Kies gives, but it didn't work there either.
Special_Kev said:
I'm definitely open to making one, but I'm confused since everything I'm reading says that the screen I described IS download mode, just with a different screen. Are you saying that you had the exact same situation as me and a Jig fixed it?
Click to expand...
Click to collapse
My phones update failed and I got the same phone, triangle, computer. I tried different USBs, different USB ports, different computers, tried Odin, nothing worked. As soon as I found my USB jig that was lying around, and plugged it in before I put in the battery, and the regular download mode which I am used to seeing showed up. ODIN recognized the phone and I flashed back to stock ICS rooted I downloaded from XDA.
Sent from my SGH-I777 using xda app-developers app
chapelfreak said:
My phones update failed and I got the same phone, triangle, computer. I tried different USBs, different USB ports, different computers, tried Odin, nothing worked. As soon as I found my USB jig that was lying around, and plugged it in before I put in the battery, and the regular download mode which I am used to seeing showed up. ODIN recognized the phone and I flashed back to stock ICS rooted I downloaded from XDA.
Sent from my SGH-I777 using xda app-developers app
Click to expand...
Click to collapse
Good enough for me. I'll give that a shot tomorrow.
Thanks for your help.
Special_Kev said:
Yes, I have tried forcing download mode by taking the battery out, holding down Vol and inserting it again. These are also the instructions that Kies gives, but it didn't work there either.
Click to expand...
Click to collapse
That's different that what I suggested. Remove the battery and leave it out. If you have to, sit on it so you won't be tempted to put it back in, lol. While holding vol down button, plug in the usb cable. The usb will supply the power. The phone should boot into download mode.
creepyncrawly said:
That's different that what I suggested. Remove the battery and leave it out. If you have to, sit on it so you won't be tempted to put it back in, lol. While holding vol down button, plug in the usb cable. The usb will supply the power. The phone should boot into download mode.
Click to expand...
Click to collapse
I guess I misread that. I blame it on my stressful week ending with no phone
So I just did that and boom, download mode as I would expect loaded up first time, no issues after I held down both Volume buttons while plugging it in (Holding down just Vol - didn't do anything). Unfortunately, it still did not show up in Odin (Kies background processes were all killed and USB driver IS installed on this computer and Odin WAS open before I plugged the phone in)
So I unplugged, opened Kies, and was going to try a restore through there since I could finally get download mode working properly. Except when I tried it this time, nothing happened. I held down the vol buttons, plugged it in, got a single vibrate, but nothing showed up on the screen. Unplugged, put the battery in, and it turned on and screen worked. Took out the battery and just plugged it in and the screen worked after vibrating 6 short pulses (It pulled up the screen mentioned in my first post). Unplugged, held down vol buttons and plugged it in, same thing. Blank screen.
Now I'm really at a loss. I'm starting to wonder if there is something wrong with my USB port on the phone itself.
Special_Kev said:
Now I'm really at a loss. I'm starting to wonder if there is something wrong with my USB port on the phone itself.
Click to expand...
Click to collapse
hey i think that i have got a solution for your problem because it also happened with me in my galaxy y and then i did this thing = :fingers-crossed: see i firstly opened odin in the desktop and then take out the battery so once the battery is out connect the usb to the phone and go onto download mode without the baterry then u'll notice in odin that ur phone is connected and then add the battery back and u r done hope it works :fingers-crossed:
ODIN doesn't detect my Samsung Galaxy ACE
personalsydic said:
hey i think that i have got a solution for your problem because it also happened with me in my galaxy y and then i did this thing = :fingers-crossed: see i firstly opened odin in the desktop and then take out the battery so once the battery is out connect the usb to the phone and go onto download mode without the baterry then u'll notice in odin that ur phone is connected and then add the battery back and u r done hope it works :fingers-crossed:
Click to expand...
Click to collapse
Hi there,
i have same problem with my Galaxy ACE GT-S5839i: i can't get ODIN to detect my phone. Originally, i tried to flash my phone and made a mistake in the process (installed a ROM before i installed CWM). This caused my phone to stop booting. The only thing remaining working is the download mode. But i can't get ODIN to detect. I tried 2 PCs, different USB ports; i tried to install Kies, or just the drivers... nothing makes ODIN detect my phone... I hear my PCs detects the phone when in download mode (it bips) and my PCs both recognized my phone (Samsung Mobile USB CDC Composite Device). On PC uses windows 7 and the other Windows Vista. I ran ODIN v4.38 on both... Would be grateful for any idea what to do...
SOLVED
canaver said:
Hi there,
i have same problem with my Galaxy ACE GT-S5839i: i can't get ODIN to detect my phone. Originally, i tried to flash my phone and made a mistake in the process (installed a ROM before i installed CWM). This caused my phone to stop booting. The only thing remaining working is the download mode. But i can't get ODIN to detect. I tried 2 PCs, different USB ports; i tried to install Kies, or just the drivers... nothing makes ODIN detect my phone... I hear my PCs detects the phone when in download mode (it bips) and my PCs both recognized my phone (Samsung Mobile USB CDC Composite Device). On PC uses windows 7 and the other Windows Vista. I ran ODIN v4.38 on both... Would be grateful for any idea what to do...
Click to expand...
Click to collapse
Actually, it works with ODIN v3.07! Finally!
---------- Post added at 07:50 PM ---------- Previous post was at 07:45 PM ----------
canaver said:
Actually, it works with ODIN v3.07! Finally!
Click to expand...
Click to collapse
Finally it works with ODIN v3.07!
Special_Kev said:
I had tried to update my phone via Kies and the computer blue screened. Now the phone is stuck on the ODIN Mode screen with a picture of my phone on the left, a yellow triangle in the middle, and a computer on the right. Taking the battery out does nothing, restarting does nothing, restarting while holding down the volume buttons does nothing. No matter what, it always comes back to this screen.
When I plug the device into my windows based PC and open ODIN, ODIN does not see my phone. When I plug it into my linux computer and run lsusb, it does not list my phone in the output, so the computer definitely isn't recognizing that my phone is plugged in. A couple of weeks ago, I had this problem while trying to back up the phone, so I'm not sure if it's related to the botched upgrade or not.
Does anyone have any tips or advice here? I'd really love to be able to use my phone again. I am using the cable that came with the phone. I have the same results with other cables, as well....
I'm happy to provide more information if needed. Just tell me what you need to know.
Click to expand...
Click to collapse
I had the same problem with kies on a sprint s2. EXACT same problem. Cord got jerked out in the middle of Odin flash. THE ONLY screen i could get is the one you described.
Also went through the steps with keis, dl firmware, got to the last part but the start button was greyed out. I had to do this several times and finally the start button lit up. Idk why it didn't work before but it finally did. Have you tried doing it more than once?
I wished i could be more help but that was my experience. Maybe it will work for you.