ive searched for things such as "sleep crash", "sleep bug", "screen wont turn on" etc. but can seem to find anything that tells me anything other than turn off wifi (which i tried to no avail). My issue is that when i press the power button for 1 second to turn off my archos 70 screen it will not turn back on. Same thing happens when i let it fall asleep. If i leave it plugged in and not allow it to turn off screen i have no issues. My apologies if i just don't know what words to search for ... i tried. In on the .4 firmware (latest) with no mods. This has happened through the last 3 firmwares from archos. Any ideas?
Have a you tried a full reinitialization (in settings > repair and formatting) and then reinstalling the latest firmware? If you have just been updating the firmware, the problem may have been deeper.
Thats strange... I have a similar issue with my 101: when i leave my tablet asleep for more than 20min, I can't turn it back on without doing a hard reset. Now it only happens when I simply shut off the screen and leave it alone. If I hold the power button and use deep sleep though, it works just fine. When I can't get it started I notice the little power light is on, but the screen stays black... any suggestions??
I have read somewhere in this forums that re-calibrating your screen from Settings might help, but I still didn't tied - if someone try please post results.
Techngro said:
Have a you tried a full reinitialization (in settings > repair and formatting) and then reinstalling the latest firmware? If you have just been updating the firmware, the problem may have been deeper.
Click to expand...
Click to collapse
I will try this and report back. I have been installing firmware over the issue
Sent from my PC36100 using XDA App
nenadr said:
I have read somewhere in this forums that re-calibrating your screen from Settings might help, but I still didn't tied - if someone try please post results.
Click to expand...
Click to collapse
I am try before formatting and report back
Sent from my PC36100 using XDA App
nenadr said:
I have read somewhere in this forums that re-calibrating your screen from Settings might help, but I still didn't tied - if someone try please post results.
Click to expand...
Click to collapse
this worked!!
mallman said:
this worked!!
Click to expand...
Click to collapse
spoke too soon. did not work. it stopped after a few tries
it works again if i recalibrate but wont hold.
Zoidpilot said:
Thats strange... I have a similar issue with my 101: when i leave my tablet asleep for more than 20min, I can't turn it back on without doing a hard reset. Now it only happens when I simply shut off the screen and leave it alone. If I hold the power button and use deep sleep though, it works just fine. When I can't get it started I notice the little power light is on, but the screen stays black... any suggestions??
Click to expand...
Click to collapse
by the way, the deep sleep option also kills mine.
Search softlocker in market, not a perfect solution but fir me work rigth. Reduce the reboots.
Sent from my A101IT using Tapatalk
ramso said:
Search softlocker in market, not a perfect solution but fir me work rigth. Reduce the reboots.
Sent from my A101IT using Tapatalk
Click to expand...
Click to collapse
just tried it . i hit the icon to disable sleeping. i pressed the screen button and when i went to turn screen back on it would not wake. Did i use the app wrong?
No, you use the app rigth. The app only disable deepsleep.
Sent from my A101IT using Tapatalk
i had the same problem on my 32, albeit not that frequently. Downloading the FW and reflashing it seems to have made the problem go away.
You know what? Strangely enough after I replied to your post I downloaded the latest fw (2.1.4) and the problem seems to have gone away no special flash no repair I just installed and rebooted and so far no prob... I will keep testing this and post results
Edit* Ok so far so good... no problems. I'm actually surprised I'm getting better response from the device despite everyone's warnings about 2.1.4. But that's another topic. I think its just a bad install of your current FW, but I'm just guessing... My device has had the issue since I got it, I just decided to live with it but like I said the latest update fixed it... So it HAS to be the FW
bbop said:
i had the same problem on my 32, albeit not that frequently. Downloading the FW and reflashing it seems to have made the problem go away.
Click to expand...
Click to collapse
err I'm afraid that I spoke too soo. My device keeps getting stuck and won't awake from sleep. This seems to happen most after switching wifi on or off, specifically whilst the device is playing music.
Zoidpilot said:
You know what? Strangely enough after I replied to your post I downloaded the latest fw (2.1.4) and the problem seems to have gone away no special flash no repair I just installed and rebooted and so far no prob... I will keep testing this and post results
Edit* Ok so far so good... no problems. I'm actually surprised I'm getting better response from the device despite everyone's warnings about 2.1.4. But that's another topic. I think its just a bad install of your current FW, but I'm just guessing... My device has had the issue since I got it, I just decided to live with it but like I said the latest update fixed it... So it HAS to be the FW
Click to expand...
Click to collapse
how are you installing the firmware? maybe im doing it wrong. I let the device update to latest 2.1.4 and then i wiped it via the settings and repair menu in android.
Edit**
like this??:
Step 1: Download the android 2.2 firmware for your archos tablet from here,you might a get a false positive notification from your browser as they are unaware of .AOS format, so ignore that and download it.
Step 2:Go to Menu > Settings > Device Storage & USB connection > USB connection mode of your tablet and set the connection mode to Mobile Media Device (MTP) and now connect your Tablet to pc.
Step 3:Now when the tablet is detected you will see a hard drive icon,double tap and open it and copy and paste the firmware (.AOS) file into the hard drive(make sure you dont copy it in any folder inside it like Music,Videos etc).
Unplug the USB connection and the Archos device will automatically locate the update file and will prompt you for the update,just follow the screen options and you are done,if it does not prompt you for an update then you might have accidentally misplaced the file in one of the folders,just locate the .AOS file from the file manager and and open it to start the update.
No no it wasn't that complicated... It was actually the simplest fix for a difficult problem. My device when I got it was running 2.1.2 out the box... Even then It had the screen problem. When I got the chance I installed 2.1.3 OVER THE AIR. Straight from Archos. Still had the issue though, I figured it would have been fixed but was greatly disappointed... Then I sort of just lived with the problem for awhile... I saw that the 2.1.4 update was released but was wary about downloading it because sooo many people are having issues. Just the other day though, the device cut off on me again and I figured to hell with it... So I downloaded the 2.1.4 OTA as well... no website, no manual install, I just let the device run its course on its own. After the update, it rebooted normally and it's been working great since... Sorry to hear not everyone is so fortunate... I really hope this helps somewhat
Related
My SGS2 stopped vibrating. Tried flashing, un-rooting, restoring stock and factory settings. None of these worked.
I am inclined to think that it is a hardware problem.
Has anyone else been dealing with issue? I read some posts on XDA regarding this matter but they were software related as opposed to hardware. Can anyone post instructions on how to fix it or provide any solutions for this issue?
If its hardware, why not flash stock, remove binary flash count with USB jig, and return for warranty?
Sent from my GT-I9100 using xda
premium
UpInTheAir said:
If its hardware, why not flash stock, remove binary flash count with USB jig, and return for warranty?
Sent from my GT-I9100 using xda
premium
Click to expand...
Click to collapse
Cannot get jig in Palestine. Bought the phone from the UK. Sending it back will be problematic. I will look for a repair shop.
Thanks for the quick reply
That's a "bummer" (bad luck). You could make a jig, but as you said that it would be problematic to return. Hope you can sort it easily. Sorry, can't think of anything of use right now.
Sent from my GT-I9100 using xda premium
hey there,
i got the same problem. no more vibrating at all. not with calls or notifications and not as haptic feedback. it started today (was still working in the morning), though i did not drop the phone or anything.
i am still hoping too find that it's a sw-problem. but all potential solutions i find do not help. so i guess i have to contact samsung.
but before i do that i have to get rid of all "hacking".
could you plz tell me what i have to do?
i have now cm9 20120402 nightly.
but i still have a cwm-recovery-backup of the original touchwiz (gingerbread).
-so first i make a backup of my current rom via cwm and of all my apps via titanium and store everything on my pc.
-i flash my touchwiz-backup
-i get one of those: http://www.amazon.de/s/ref=nb_sb_no...ld-keywords=Samsung+Galaxy+S2+USB+Jig&x=0&y=0 , plug it in, wait til its done and remove it again.
after that, samsung will never know i "messed" with the phone??
or do i have to consider/do something else?
tyvm!!
kws
I have the same issue.
When I was on my stock 2.3.5, I found a workaround:
- go into test mode (dial *#0*#)
- find the vibrate button, when you press it, it shouldn't work like you expect
- go back
- plug in your headphones and push the cable a bit to the left
- test vibrate again - this time it should work
- pull the cable out while vibrating, still pushed to the left, vibrations should stay on
I know it sounds crazy but it seems the hardware part that controls the vibrations is near to the jack port - excessive use of headphones, like it was case, must have damaged it somehow.
However, now I'm on CM9, so no test mode for me, I'm achieving the same effect by bashing the back button, so I get semi-constant vibration. I know, It's ridiculous.
Have the same problem here, I think it's software related because the shut down vibration stopped working when I flashed CM9 ICS, I can't remember if it was working anywhere else though. But now I'm back to 2.3.5 and it's not working at all. Did a Factory Reset, Cleaned Cache before and after the flash. Also used the Jig to reset my counter. Any clues?
I am experiencing the same issue.
Yesterday, I downgraded from 4.0.3 back to 2.3.5 as I was having a lot of problems with ICS. Now, my phone works fine again except for the fact that it does not vibrate anymore. (Which it did fine in 4.0.3 and before in 2.3.5)
I tried the trick Lechium06 mentioned in this thread but that did not work for me.
Anyone else having this issue? More important, anyone have a solution???
Greetinx
Johan
dajomas said:
I am experiencing the same issue.
Yesterday, I downgraded from 4.0.3 back to 2.3.5 as I was having a lot of problems with ICS. Now, my phone works fine again except for the fact that it does not vibrate anymore. (Which it did fine in 4.0.3 and before in 2.3.5)
I tried the trick Lechium06 mentioned in this thread but that did not work for me.
Anyone else having this issue? More important, anyone have a solution???
Greetinx
Johan
Click to expand...
Click to collapse
I saw something similar on CM9 thread, they said it could be a "bad flash", not a corrupted rom but the lack of proper cleanup before and after the flash. But I cleaned up everything before and after and I don't like reconfiguring the whole phone again for nothing.
it happend again.
dont recall what i did or if i did something last time at all. but it worked for over a year now. and now, my sgs2 doesnt vibrate at all, i tried all possible settings, tested with z-device and rebooted. nothing.
apprechiate any hint!
thx!!
kws
AW: [Q] Vibrate function doesn't work anymore, hardware issue
since i had that before, i ruled out a hardware issue. it happend when i played with the system settings. but as i sayed, i tried to reverse everything i did. now after i updated to 0206 and wiped cache and dalvik, still no vibration.
is there anything i could have missed?
is there a possibility to reset all settings to default without deleting all my data?
thx,
kws...
...tapatalking
kweso said:
since i had that before, i ruled out a hardware issue. it happend when i played with the system settings. but as i sayed, i tried to reverse everything i did. now after i updated to 0206 and wiped cache and dalvik, still no vibration.
is there anything i could have missed?
is there a possibility to reset all settings to default without deleting all my data?
thx,
kws...
...tapatalking
Click to expand...
Click to collapse
I assume since your posting in xda developers that you are rooted?
If so, just back up data with titanium backup app and factory reset, setup system and then restore USER apps and data only.
Sent from my GT-I9300 using xda premium
kweso said:
it happend again.
dont recall what i did or if i did something last time at all. but it worked for over a year now. and now, my sgs2 doesnt vibrate at all, i tried all possible settings, tested with z-device and rebooted. nothing.
apprechiate any hint!
thx!!
kws
Click to expand...
Click to collapse
Did you install another rom?
My vibration for example didn't work with some cm10.1 nightlies
it started in cm10.1 20130203. then i tried wipe cache and dalvik. nothing. then i updated to 0206 (wiped cache and dalvik again) > still nothing. went to bed. got up. everything ok! its vibration again! i am 100% sure, it did not work, when i left it on my desk last night. this morning, i checked for missed calls and it took a moment until i realized: i got haptik feedback back on patternunlock and keystrokes! checked ringtone-vibration: fine as well!
dont ask me how! would still like to know for myself.
thx,
kws
AW: [Q] Vibrate function doesn't work anymore, hardware issue
call me stupid!
suddenly this evening my phone stopped vibrating again. then i realized: quiet hours! i turned off haptik feedback at night.
could slap myself. at least ill find this thread again, next time i screw it again....
nite,
kws...
...tapatalking
Girls can use it again then. Good news for them!
Sent from the little guy
Hello
sorry for my english.
When I'm not plugin with the usb power connected, I've got a stranger behaviour very disturbing.
When my device goes itself or by on/off push buttons in sleep, automatically it reboot itself.
So, if I let him alone, the battery fall down very quickly, and I have to wait the rebooting before to use it.
I've read something which could help me here, but not enought : "http://forum.xda-developers.com/showthread.php?t=1184852"
. Do you think, it could come from Avast?
. I tried different ROM official and no unficial, sill the same. The thing strange, and after a official instal, the behaviours has desapear until i reboot.
Archos 80 Gen 9
3.2.79 from surdu_petru
In advance thank you.
A first solution : airplane mode
Bonjour,
I've found this solution http://forum.archosfans.com/viewtopic.php?f=74&t=53186
Put your device in airplane mode. Go in sleep (black screen). Push the ON button. Remove airplane mode. It's working! I don't know why?
It's not efficient for me. I have to know why, and how to solve it!
If you restart your device, and the WIFI was activated, you have to do it again.
Let's see what happen in the few day.
It has worked only one time.
In fact, if I let Avast make a scan or i let a music player, every thing is all right.
I do not understand what's happen....
decrase the Brightness
Nop
Thanks you for this answer but it didn't work. I decrease the brightness but same behaviour.
Mine has done the same thing. It's annoying. Just won't wake up, have to reboot. On newest FW too.
Sent from my ADR6425LVW using xda premium
reverendbill said:
Mine has done the same thing. It's annoying. Just won't wake up, have to reboot. On newest FW too.
Sent from my ADR6425LVW using xda premium
Click to expand...
Click to collapse
Your issue is different. You have used Paul's root method and done nothing afterwards, see my thread
Sent from my ARCHOS 80G9 using xda premium
Quinny899 said:
Your issue is different. You have used Paul's root method and done nothing afterwards, see my thread
Sent from my ARCHOS 80G9 using xda premium
Click to expand...
Click to collapse
Mine's bone stock. Haven't done anything to it yet besides the factory firmware update. Was about to start rooting it, but haven't yet. About to hit up your thread to get that going. I DID have it airplane mode today, as I was on an airplane, hit the button, came right up. There's something to that...
Add
Thanks
To add some information -
I have done your procedure : http://forum.xda-developers.com/showthread.php?t=1456875
. Step 1: Gain temp root - OK Every works corectly (I only used the original post from Paul's root)
. Step 2: Enable SDE and Permanently root your tablet I do not did the last step below :
15. Turn off your device again and boot back into recovery
16. Select Developer Menu > Remove android Kernel
17. Accept warnings (MEDIA & APPS WILL BE UNAFFECTED)
18. Reboot. Your device will now boot the rooted edition every time
Click to expand...
Click to collapse
. Other thing, my archos do not seam to be rooted : When I'm trying to use titanium, it explain that it should be not rooted.
I've changed the method to the right one. Check my thread
Sent from my HTC Desire HD using xda premium
No
I tried 3 times. but still the same behaviour.
After a reboot or after that I install a appli, same behaviour. Very supprising.
Do you have any idea?
Cool
Trop bien!
It seams that the v 3.2.80
which have this correction : Hard drive based products: avoid suspend/resume issues happening sometimes
correct effectively those wrong behaviour.
I will confirm you next week that it's "SOLVED"
I'm trying this update tonight!
I like this tablet, except the damn sleep of death, which I JUST had to go through to boot it up to check the firmware version. If that gets fixed, I can permanently replace my Acer A100. It is the most annoying thing about this tablet. I do have a 250gb G80. Hope this does it.
So far so good, wakes right up. Need to let it sit for a bit and let it idle awhile.
Sent from my ARCHOS 80G9 using xda premium
Solved
Yes we can considering that the pb is closed.
See you.
gahia said:
Yes we can considering that the pb is closed.
See you.
Click to expand...
Click to collapse
3 days, working like a champ, thanks ARCHOS! Glad to see they seem to listen..
Sent from my ARCHOS 80G9 using xda premium
Hi all,
This is my first thread... I've looked every forum, every existing thread looking for an explanation / solution, with no luck at all... I hope somebody has experienced this with its prime and found a solution, because I'm thinking in RMA it...
The thing is that my sensors stopped working! No accelerometer, no magnetometer. The screen rotates itself to portrait mode when an app asks for it, but it stays that way when exiting the app. I have to go to Settings -> Display to uncheck and check Autorotation to go back to landscape mode. This is annoying! I installed an app called Elixir 2 and in the sensors page only the microphone is listed as present. Every other sensor is displayed as not present.
I noticed it two weeks ago, but I wanted to look for a solution instead of getting it replaced. I think it came with a .15 and it was updated to .21 in the first connection to Internet. I waited for the .28 to be released just in case it fixed the problem, but it did nothing, still has the problem.
By the way, I tried a cold boot and a factory reset... still nothing.
If I can have any word from anyone I will be pleased!
Thank you!
PS: forgive my english, I'm from Spain
Get the app called elixir2. its free. Kirk show u detailed info on everything, including sensors. itll show real time info on them. allows u to cut them off n on or reset them. it might help.
demandarin said:
Get the app called elixir2. its free. Kirk show u detailed info on everything, including sensors. itll show real time info on them. allows u to cut them off n on or reset them. it might help.
Click to expand...
Click to collapse
Well, that's exactly what I did! I said it before It just shows an X beside every sensor and under them it says something like "not present" (I don't have the Prime here right now). In that sensors page the only one that is shown as working is the microphone.
Any idea?
Thank you anyway!
demandarin said:
Get the app called elixir2. its free. Kirk show u detailed info on everything, including sensors. itll show real time info on them. allows u to cut them off n on or reset them. it might help.
Click to expand...
Click to collapse
Here's a snapshot of the Elixir2 sensors' page.
Hi, I cannot suggest anything new to try.
Today I noticed some of my sensors were not working, tried playing Riptide and found I could not turn. Also tried a level app and found that the orientation was not being detected. My problem was fixed by powering off then turning on again. I did not try elixir2 before the power off, therefore could not say if my prime was in a similar state.
Good luck in getting your prime going again.
Cheers stv
Sent from my Transformer Prime TF201 using XDA
stvlgm said:
Hi, I cannot suggest anything new to try.
Today I noticed some of my sensors were not working, tried playing Riptide and found I could not turn. Also tried a level app and found that the orientation was not being detected. My problem was fixed by powering off then turning on again. I did not try elixir2 before the power off, therefore could not say if my prime was in a similar state.
Good luck in getting your prime going again.
Cheers stv
Sent from my Transformer Prime TF201 using XDA
Click to expand...
Click to collapse
Well, at least someone experienced the same... even with a reset I can't make it work. Is there any "ultra-reset" I can do?
Before .28 I get the same issue.
Sensor can restart after a reboot or a cold start, but after I plug on the dock or after a deep sleep,the sensor stop.
Sometime, after a restart the sensor was not recognized. I use elixir also to check.
Now with .28, the sensor work well.
DesmoRFR said:
Before .28 I get the same issue.
Sensor can restart after a reboot or a cold start, but after I plug on the dock or after a deep sleep,the sensor stop.
Sometime, after a restart the sensor was not recognized. I use elixir also to check.
Now with .28, the sensor work well.
Click to expand...
Click to collapse
Did you update to .28 over wifi or using a microSD?
Thank you!
Update done through Microsd.
I have tweaked buil.prop on .21 and result Fota didn't work.
Think also to make a cold reboot and clear cache of all application (can be done with elixir).
demandarin said:
Get the app called elixir2. its free. Kirk show u detailed info on everything, including sensors. itll show real time info on them. allows u to cut them off n on or reset them. it might help.
Click to expand...
Click to collapse
demandrin - off topic, do you know where I may be able to get the circiut board that has the microsd slot and the touch screen sensor connectors. I accidentally damaged the connectors and now I can only use the tablet with the keyboard dock as a mini laptop. I emailed Asus but they would not sell me the part. I wonder if Gary would be nice enough to sell me the part.
Is HP the only company that sells parts to customers (I love HP for that reason LOL!!)
DesmoRFR said:
Before .28 I get the same issue.
Sensor can restart after a reboot or a cold start, but after I plug on the dock or after a deep sleep,the sensor stop.
Sometime, after a restart the sensor was not recognized. I use elixir also to check.
Now with .28, the sensor work well.
Click to expand...
Click to collapse
An update with my problem: I finally installed the .28 through SD card, having wiped all the data first, and the result is the same: no sensors are present. No autorotation, no compass, no auto-brightness. Elixir shows only the microphone as one of the sensors, everything else is shown as "not available" (as shown on my previous snapshot).
Any help?
Thank you!
sunne2k said:
An update with my problem: I finally installed the .28 through SD card, having wiped all the data first, and the result is the same: no sensors are present. No autorotation, no compass, no auto-brightness. Elixir shows only the microphone as one of the sensors, everything else is shown as "not available" (as shown on my previous snapshot).
Any help?
Thank you!
Click to expand...
Click to collapse
And yesterday, with no reason at all, ALL of my sensors (accels, gyro, magnet field, etc.) started working again. I just powered the tablet on and voilà, everything was perfect! Elixir showed all the sensors up and running!
I think this post can be closed now... I hope it doesn't happen again!
Hi everyone...
Some days ago, i was trying, OmniROM (http://forum.xda-developers.com/showthread.php?t=2544790). I follow all the steps and even get the superSU app going. One night, y saw how my nightly got updated, and in the morning, start to reboot randomly. If I push the power botton sometimes, doesn´t appear the blockscreen but the screen with the reboot option and turn off appear...
I put my cellphone back to stock with root using SuperOneClick from here: http://forum.xda-developers.com/showthread.php?t=1311081. Then, I format my sd card and internal storage...The problem persist...
I would like that someone help me, I'm tryin everything and didn't solve it...
Based on your description, it sounds like a hardware issue -more specifically, a failing power button.
I have read that some users were able to fix the issue by disassembling the phone and spraying out the switch with contact cleaner, and I have read that others had the power switch replaced altogether.
Hopefully others will chime-in with their thoughts.
Leo Dorado said:
Hi everyone...
Some days ago, i was trying, OmniROM (http://forum.xda-developers.com/showthread.php?t=2544790). I follow all the steps and even get the superSU app going. One night, y saw how my nightly got updated, and in the morning, start to reboot randomly. If I push the power botton sometimes, doesn´t appear the blockscreen but the screen with the reboot option and turn off appear...
I put my cellphone back to stock with root using SuperOneClick from here: http://forum.xda-developers.com/showthread.php?t=1311081. Then, I format my sd card and internal storage...The problem persist...
I would like that someone help me, I'm tryin everything and didn't solve it...
Click to expand...
Click to collapse
cyril279 said:
Based on your description, it sounds like a hardware issue -more specifically, a failing power button.
I have read that some users were able to fix the issue by disassembling the phone and spraying out the switch with contact cleaner, and I have read that others had the power switch replaced altogether.
Hopefully others will chime-in with their thoughts.
Click to expand...
Click to collapse
Well, i will try that. It's a shame that such a good cellphone have that problem... I really love it... Thanks for your answer.
Leo Dorado said:
Well, i will try that. It's a shame that such a good cellphone have that problem... I really love it... Thanks for your answer.
Click to expand...
Click to collapse
I had to replace my power button. this is a known issue with the s2.
I recommend this guy's services: http://stores.ebay.com/t989-refurb -- he can do the i777 even though it's not listed. He's a very nice guy and will do a fine job.
here's his video demonstration: http://www.youtube.com/watch?v=F0xMMn1DRWs
Hello everyone i hope someone can help me. I rooted my Kindle Fire HDX using KFHDX Tool Kit and it was successful. Afterwards i installed SUPERSU by way of the program itself and also disabled OTA. Now my problem happened after disabling OTA my silk browser will not work at all even though the WIFI is connected so i did a factory reset now when i power on my unit it keeps prompting me to choose a language even though i have already chosen one it will just keep going back to that screen. I was able to bypass it by tapping quickly on the screen and i was able to go to contacts and from there i am able to go to settings via the drop down menu. The problem is i cannot access home because when i press back it will just show home for a split second and then go back to the language menu even if i tried all the languages it wont let me use the tablet. Also i remember having paused the update before attempting to root. Now i cannot proceed to use my tablet at all. Can someone help me out with my predicament? I would really appreciate it, Thank you.
momayhem03 said:
Hello everyone i hope someone can help me. I rooted my Kindle Fire HDX using KFHDX Tool Kit and it was successful. Afterwards i installed SUPERSU by way of the program itself and also disabled OTA. Now my problem happened after disabling OTA my silk browser will not work at all even though the WIFI is connected so i did a factory reset now when i power on my unit it keeps prompting me to choose a language even though i have already chosen one it will just keep going back to that screen. I was able to bypass it by tapping quickly on the screen and i was able to go to contacts and from there i am able to go to settings via the drop down menu. The problem is i cannot access home because when i press back it will just show home for a split second and then go back to the language menu even if i tried all the languages it wont let me use the tablet. Also i remember having paused the update before attempting to root. Now i cannot proceed to use my tablet at all. Can someone help me out with my predicament? I would really appreciate it, Thank you.
Click to expand...
Click to collapse
Happened to me as well, you need to get supersu installed and it'll stop doing it.
derpadoodle said:
Happened to me as well, you need to get supersu installed and it'll stop doing it.
Click to expand...
Click to collapse
Hi derpadoodle. I was also able to fix it by doing another factory reset and redoing superSU and OTA. Was able to install es file explorer via third party website and the Gapps. Almost thought that its already dead just bought it 3 days ago..
Im having another problem sometimes when i turn on my wifi my unit reboots itself.. It has happened a couple of times already.. any solution to this?
momayhem03 said:
Hello everyone i hope someone can help me. I rooted my Kindle Fire HDX using KFHDX Tool Kit and it was successful. Afterwards i installed SUPERSU by way of the program itself and also disabled OTA. Now my problem happened after disabling OTA my silk browser will not work at all even though the WIFI is connected so i did a factory reset now when i power on my unit it keeps prompting me to choose a language even though i have already chosen one it will just keep going back to that screen. I was able to bypass it by tapping quickly on the screen and i was able to go to contacts and from there i am able to go to settings via the drop down menu. The problem is i cannot access home because when i press back it will just show home for a split second and then go back to the language menu even if i tried all the languages it wont let me use the tablet. Also i remember having paused the update before attempting to root. Now i cannot proceed to use my tablet at all. Can someone help me out with my predicament? I would really appreciate it, Thank you.
Click to expand...
Click to collapse
Go back to root tool. Enable ota updates. Register tablet. Disable ota. It keeps going to language because it can not contact amazon to set up. This exact thing happened to me. That's how I fixed it
conan1600 said:
Go back to root tool. Enable ota updates. Register tablet. Disable ota. It keeps going to language because it can not contact amazon to set up. This exact thing happened to me. That's how I fixed it
Click to expand...
Click to collapse
Thanks. I was able to fix it by resetting to factory settings, registering and then doing everything again. Do you know of any solutions to the wifi problem where when you turn on the wifi the unit reboots?
try this
momayhem03 said:
... Do you know of any solutions to the wifi problem where when you turn on the wifi the unit reboots?
Click to expand...
Click to collapse
posted by Hashcode somewhere in development section
...If you try and start Wifi and the device crashes/reboots, try turning on bluetooth prior to enabling wifi and see if that works...
hope it will work for you :good:
jeryll said:
posted by Hashcode somewhere in development section
...If you try and start Wifi and the device crashes/reboots, try turning on bluetooth prior to enabling wifi and see if that works...
hope it will work for you :good:
Click to expand...
Click to collapse
Thanks bro! I also seem to see that when my unit turns on the bluetooth icon appears beside the wifi indicator but when i go to settings > wireless and i check my bluetooth it is turned off LOL. Needed to turn it on and off for the icon to disappear. Anyways did the updates ever solved this problem? not really a biggie for me but it is nice if i can turn off my wifi.